Sie sind auf Seite 1von 64

HUAWEI TECHNOLOGIES CO., LTD.

All rights reserved


www.huawei.com
Internal
WCDMA BTS3900
Hardware Structure
BTS3900V200R011
WRAN Training Team
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 2
As an important part of UTRAN,
NodeB mainly processes the signals of
physical layer of Uu interface
BTS3900 is a new generation indoor
marco NodeB which is produced by
Huawei Co. Ltd.

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 3
Upon completion of this course, you will be able to:
Master the hardware structure of BTS3900
Master the working principle of different subsystems and
boards of BTS3900
Master the cables connection rules of BTS3900
Know typical configurations of BTS3900
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 4
BTS3900 Product Description
BTS3900 Hardware Description
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 5
Chapter 1 NodeB Overview
Chapter 2 BTS3900 Hardware Structure
Chapter 3 BTS3900 Typical Configuration
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 6
Abbreviations
WMPT WCDMA Main Processing and Transmission Unit
WBBPa WCDMA Baseband Process unit Type A
WRFU WCDMA Radio Filter Unit
UBFA Universal BBU Fan Unit Type A
UEIU Universal Environment Interface unit
UELP Universal E1/T1 Lighting Protection unit
UFLP Universal FE/GE Lighting Protection unit
UPEU Universal Power and Environment Interface Unit
UAEU Universal ATM over E1/T1 Interface and Processing Unit
UIEU Universal IP Packet over E1/T1 Interface and Processing Unit
UTRP Universal Transmission Processing Unit
DCDU-01 Direct Current Distribution Unit-01
CPRI Common Protocol Radio Interface
PSU The power supply unit
PMU The power and environment monitoring unit
APM Advanced Power Module
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 7
NodeB Position in UMTS Network
Iu-BC
RNC
RNC
NodeB
NodeB
NodeB
CS
PS
CBC
UE UTRAN CN
Uu Iu
Iu-CS
Iu-PS
Iu-BC
Iur
Iub
Iub
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 8
NodeB System Architecture
Environment
Monitoring
device
Iub
Uu
UE
RNC
BTS3900 cabinet
O&M terminal
BTS3900 System

power supply
system
GPS antenna & feeder system
Clock synchronization source
Internal Clock
Antenna & feeder
subsystem
Transmission
device
DDF
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 9
Chapter 1 NodeB Overview
Chapter 2 BTS3900 Hardware Structure
Chapter 3 BTS3900 Typical Configuration
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 10
Chapter 2 BTS3900 Hardware Structure
Section 1 BTS3900 Introduction
Section 2 BBU Modules Structure
Section 3 RF Modules Structure
Section 4 Power Modules Structure
Section 5 BTS3900 Cables
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 11
BTS3900 Appearance
Type Parameters
Dimensions 600(W)*900(H)*450(D)
Empty cabinet 70kg
Weight under full
configuration
160Kg
3*1 and 3*2 Weight 120Kg
- 48V : Input range of
voltage
-38.4V DC to -57V DC
+24V: Input range of
voltage
+21.6 V DC to +29 V DC
200 V AC to 240 V AC 200 V AC to 240 V AC 176 V AC to
290 V AC, single-phase
200 V AC/346 V AC to
240 V AC/415V AC
176 V AC/304 V AC to 290 V AC/500
V AC, three-phase
Working Temperature
-20+50
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 12
BTS3900 Single Cabinet Full Configuration Structure
+ 24VDC
Single Cabinet
220V AC
Single Cabinet
- 48VDC
Single Cabinet
1U
9U
2U
1U
1U
19U
2U
2U
1U
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 13
BTS3900 Stacked Cabinets Full Configuration Structure
3U
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 14
BTS3900 Capacity and Characteristics
System capacity specifications:
BTS3900 can support up to: uplink 1536 CEs and downlink 1536 CEs
BTS3900 can support up to: 3*8 cells or 6*4 cells
Characteristics
Transmission Type: E1/T1, FE (electrical port ), FE (optical port ),
Networking mode: star, chain, tree and hybrid
Synchronization clock sources: Iub interface clock, GPS, and internal clock
Handover types: softer handover, soft handover and hard handover
Services: CS services, PS services , mixed services and position services
Enhanced functionsRET , HSDPA , HSUPA phase II
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 15
BTS3900 Logical Structure
PSU
RF Module
DCDU
WRFU
RNC
Antenna
Iub
WRFU
BBU
Power
Module
Baseband Transmission
Control module
+24V/220V -48V
Signal Current
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 16
Chapter 2 BTS3900 Hardware Structure
Section 1 BTS3900 Introduction
Section 2 BBU Modules Structure
Section 3 RF Modules Structure
Section 4 Power Modules Structure
Section 5 BTS3900 Cables
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 17
Logical Structure of the BBU3900 Module
TO WRFU
Clock mode
Signaling
Processing
Operation&
Maintenance
Power mode
E1/T1
FE
Transport
Interface
Transmission
Adaptation
Protocol
Processing








F
P

P
r
o
c
e
s
s
i
n
g

Codling
Decoding Demodulation
Modulation
Interface

Module
Transport Subsystem Baseband Subsystem
Control Subsystem
External Subsystem OMC
CPRI
RNC
Power
Control
information
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 18
BBU3900 Module Introduction
Mandatory boards and modulesWMPT, WBBP, UBFA, and UPEU
The optional boards are the UELP, UFLP, UTRP, and UEIU.
Full configuration
Typical configuration
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 19
BBU3900 Module Introduction
Slot
16
Slot 18
Slot 19
SLOT0
SLOT1
SLOT2
SLOT3
SLOT4
SLOT5
SLOT6
SLOT7
Active and standby slot definition
only for UTRP board
B
F
A
PEU/
EIU
PEU/
EIU
WBBP
WBBP
WBBP
WBBP
UTRP
UTRP
WMPT
WMPT
Slot boards definition
available UFLP
available UELP
available available available available WBBP
available available available available available available UTRP
available available WMPT
Slot 7 Slot 6 Slot 5 Slot 4 Slot 3 Slot 2 Slot 1 Slot 0 Board
available
available
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 20
BBU Module --- WMPT Board
Board number
maximum is 2 for one BBU
mandatory board
working in active and
standby
4E1:DB26
IP transmission on
Electrical Port :RJ45
IP transmission
Optical signals: SFP
GPS antenna: SMA
Commissioning:RJ45
Loading Testing:USB
LEDs
Main Functions
Providing OM functions
Controlling other boards in the system and
providing the reference clock
Providing USB ports for automatic NodeB
upgraded
Providing transmission port for Iub interface
Providing OM channels
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 21
BBU Module --- WMPT Board
LEDs of running status of WMPT:
Label Color Status Description
RUN Green ON The board has power input, yet the board is faulty.
OFF The board has no power input.
1s ON, 1s OFF The board is running as configured.
0.125s ON, 0.125s OFF The software is being loaded to the board, or the
board is not in use.
ALM Red ON The board is reporting hardware alarms.
OFF
The board is running properly.
ACT Green ON The board is in active mode.
OFF The board is in standby mode.
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 22
BBU Module --- WMPT Board
LED Color Status Description
LEDs beside the
FE1 and FE0 optical
port
Green ON The connections are functional.
OFF The connections are faulty.
Yellow Blinking There is ongoing data transmission.
OFF There is no data transmission.
LEDs beside the
ETH port
Green ON The connections are functional.
OFF The connections are faulty.
Yellow Blinking There is ongoing data transmission.
OFF There is no data transmission.
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 23
BBU Module --- WMPT Board
Two DIP Switches :
SW1 for setting the E1/T1 working mode
SW2 for setting the protection ground for the E1.
Settings of SW1
Bit T1 Mode 120-ohm E1
Balanced Mode
75-ohm E1
Unbalanced Mode
1 ON OFF ON
2 ON OFF ON
3 OFF ON ON
4 OFF ON ON
Settings of SW2
Bit 120-ohm E1
Balanced Mode
75-ohm E1
Unbalance
d Mode

Description

1 OFF ON The RRING is for
connected to the
protection ground
2 OFF ON
3 OFF ON
4 OFF ON

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 24
BBU Module --- WBBPa Board
Board number mandatory board, maximum is 6
Main Functions
Providing the CPRI interface for communication between the BBU and the
WRRU or WRFU
Processing uplink and downlink baseband signals and support HSUPA and
HSDPA function
Supporting 1+1 backup of the CPRI interface
According to the board chip processing capability, WBBP module include
seven specifications. Current WBBP is the A version, called WBBPa.

CPRI 0~2 (1.25G-2.5G): SFP LEDs
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 25
BBU Module --- WBBPa Board
LED of running status of board :
Label Color Status Description
RUN Green ON The board has power input, yet the board is faulty.
OFF The board has no power input or is faulty.
1s ON, 1s OFF The board is running properly.
0.125s ON/OFF Software is being loaded to the board.
ACT Green ON The board is running properly.
OFF The board is not in use.
ALM Red OFF The board is running properly.
ON
The board has alarms on hardware and it should be replaced with a new one.

CPRI0
CPRI1
CPRI2

Red
Green
OFF normal
ON
The CPRI links over the optical cable are faulty.
Blinking at 2 Hz
The RRU on the CPRI link is faulty in hardware.
Blinking at 0.5 Hz
The RRU on the CPRI link is faulty in the antenna system connection.
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 26
BBU Module --- WBBP Board
There are 2 kinds of Baseband card, WBBPa and WBBPb.
The WBBPa support HSDPA (2 ms TTI) and support for HSUPA phase I (10 ms TTI).
The WBBPb support HSDPA (2 ms TTI), and support for HSUPA phase II (2 ms TTI).
Board
Type Cell
Uplink R99
/HSUPA CE
Downlink
R99 CE HSDPA Capacity HSUPA
WBBPa 3 cells 128 256 45 HS-PDSCH codes Phase 1
WBBPb1 3 cells 64 64 45 HS-PDSCH codes Phase 1
WBBPb2 3 cells 128 128 45 HS-PDSCH codes Phase 2
WBBPb3 6 cells 256 256 90 HS-PDSCH codes Phase 2
WBBPb4 6 cells 384 384 90 HS-PDSCH codes Phase 2
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 27
Label Color Status Description
STATE Green 0.125s ON,
0.125s OFF
The module is not registered, and no
alarm is reported.
1s ON, 1s OFF The board is running properly.
Red ON The module is reporting alarms.
BBU Module --- UBFA Board
Board number mandatory board, maximum is 1
Main Functions
Controlling the fan speed
Reporting the fan status to the WMPT
Detecting the temperature of the fan board
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 28
Panel of the UPEA
Panel of the UPEB
BBU Module --- UPEU Board
Board number mandatory, maximum is 2, 1+1 backup
Main Functions
Converting -48 V or +24 V DC power input to +12 V DC power that is supported
by boards
Reporting alarms related to input and output under voltage
Providing transmission ports for RS485 signals and 8 dry contact alarm signals
-48V to +12V
+24V to +12V
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 29
LED: The UPEU has one LED, indicating the running status of the board.
Label Color Status Description
RUN Green ON
The board is running properly.
OFF The board has no power input, or
the board is faulty.
Socket and Port: The UPEU has one socket and four ports.
Label Quantity Connector Type Function
PWR 1 3V3 DC power input
EXT-ALM1 1 RJ45 Transmitting dry contact alarm signals
EXT-ALM0 1 RJ45
MON1 1 RJ45 Transmitting RS485 environment
monitoring signals
MON0 1 RJ45
BBU Module --- UPEU Board
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 30
The UTRP provides ports for eight E1s/T1s and implements transport such as IP and
ATM between the BBU3900 and the RNC.
Label Color Status Description
RUN Green ON The board has power input, yet the board is faulty.
OFF The board has no power input or is faulty.
1s ON, 1s OFF
The board is running properly.
0.125s ON, 0.125s OFF Software is being loaded to the board.
2s ON, 2s OFF The board is under test.
ACT Green ON The board is in active mode.
OFF The board is in standby mode.
ALM Red OFF The board is running properly.
ON The board is reporting alarms and is faulty.
BBU Module --- UTRP Board
4 E1:DB26
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 31
BBU Module --- UTRP Board Type
WCDMA UTRP extend transmission board
UTRP board should add sub board to provide the different interface type.
WD22UTRP is the main board name. The UTRP has three sub-boards in current
version
UAEU: Eight ATM over E1s/T1s
UIEU: Eight IP over E1s/T1s
UUAS: One unchannelized ATM over SDH/SONET(STM-1/OC-3) interface
The board in gray table is not be delivered currently.
Board Port
UTRP2 Two universal FE/GE optical port
UTRP3 Ports for eight channels of ATM over E1/T1
UTRP4 Ports for eight channels of IP over E1/T1
UTRP6 Port for one unchannelized STM-1/OC-3
UTRP9 Four universal FE/GE electrical ports
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 32
Label Connector Type
MON0 RJ45
MON1 RJ45
EXT-ALM0 RJ45
EXT-ALM1 RJ45
BBU Module --- UEIU Board
Port : The UEIU has four ports.
Board number: maximum is 1
The UEIU Functions
Connecting to an external monitoring device and transmitting RS485
signals to the WMPT
Connecting to an external alarm device and transmitting dry contact alarm
signals to the WMPT
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 33
BBU Module --- SLPU Board
The auxiliary devices of the
BBU3900. The devices are
the SLPU, UELP, and UFLP
SLPU: The signal lightning
protection unit is an optional
module of the BTS3900
cabinet (-48 V) or the power
distribution cabinet.
The UFLP and the UELP
are optional units that are
installed in the SLPU.
UFLP
UELP
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 34
UELP: The universal E1/T1 lightning protection (UELP) unit is a universal E1/T1
The UELP can be optionally installed in the SLPU or the BBU. Each UELP
supports the surge protection of 4-way E1/T1 signals.
E1 Connection:
BBU Module --- UELP Board
DB25
DB26
Indoor DDF
E1
E1
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 35
DIP Switch: The UELP has one DIP switch, which is used to select whether the
receive terminal is grounded. The DIP switch has four bits.
DIP
Switch
DIP Status Description
1 2 3 4
S1 ON ON ON ON Used for the 75
unbalanced mode
OFF OFF OFF OFF Used for other
modes except the 75
unbalanced mode
BBU Module --- UELP Board
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 36
UFLP: The universal FE lightning protection (UFLP) board is optionally installed in the
SLPU or BBU. Each UFLP supports 2-way FE surge protection.
BBU Module --- UFLP Board
IP Cable Connection.
Transmission Equipment
LAN switch or Router
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 37
Chapter 2 BTS3900 Hardware Structure
Section 1 BTS3900 Introduction
Section 2 BBU Modules Structure
Section 3 RF Modules Structure
Section 4 Power Modules Structure
Section 5 BTS3900 Cables
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 38
RF Module --- WRFU Board
The WRFU consists of the high-speed interface unit, signal processing unit,
power amplifier, and duplex unit
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 39
RF Module --- WRFU Board
Type Label Connector Type Description
Port for
transceiving RF
signals
ANT-RXB DID connector Connecting the antenna
subsystem
ANT-TX/RXA DID connector
CPRI CPRI0 SFP female
connector
Connecting the BBU, or
the upper-level WRFU
during the cascading
CPRI1 SFP female
connector
Connecting the lower-
level WRFU during the
cascading
Interconnection port
for RF receive
signals
RX-INB QMA female
connector
Input port of diversity
signals in the antenna
channel
RX-OUTA QMA female
connector
Output port of diversity
signals in the antenna
channel
Power port PWR 3V3 power
connector
Introducing power
Commissioning port MON RJ45 connector Used for commissioning
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 40
Identifier Status Meaning
RUN On The power input is normal, but the module is faulty.
Off There is no power input, or the module is faulty.
On for 1 second and off for 1 second The module is functional.
On for 0.125 second and off for 0.125
second
The module is loading software or is not started.
ALM On The module is in the alarm status.
Off No alarm is generated.
ACT On The module is functional and is connected to the BBU.
Off The module is not connected to the BBU.
On for 1 second and off for 1 second The module is in the local test status.
VSWR Off (red) No VSWR alarm is generated.
On (red) A VSWR alarm is generated.
CPRI0
CPRI1
On (green) The CPRI link is normal.
On (red) The interface module fails to receive signals.
Red LED on for 1 second and off for
1 second
The CPRI link is out of lock.
RF Module --- WRFU Board
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 41
RF Module --- WRFU Board
RF specifications:
One WRFU supports four carriers
Each carriers maximum output power of WRFU is 80W
The receive sensitivity of single antenna is better than -125.8dBm
The receive sensitivity of two antennas is better than -128.6dBm
The maximum searching ability is 200km
The maximum access search radius is configurable with the step size of 300 m
Configuration Type (No
Transmit Diversity)
Transmit Diversity
Power (W)/Carrier
Typical Power
Consumption (W)
Maximum Power
Consumption (W)
3*1 20 520 630
3*2 20 610 830
3*3 20 810 1070
3*4 20 1020 1330
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 42
Chapter 2 BTS3900 Hardware Structure
Section 1 BTS3900 Introduction
Section 2 BBU Modules Structure
Section 3 RF Modules Structure
Section 4 Power Modules Structure
Section 5 BTS3900 Cables
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 43
Power Distribution Modes of the BTS3900
- 48 V DC Distribution
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 44
Power Distribution Modes of the BTS3900
+24 V DC Distribution
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 45
Power Distribution Modes of the BTS3900
220 V AC Distribution
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 46
- 48V Cabinet Power Module --- DCDU-01 Board
Function
The DCDU-01 supports one -48 V
DC power input and ten -48 V DC
power outputs
The DCDU-01 supplies power to
the BBU, WRFU, FAN, and user
devices inside cabinets
The DCDU-01 has the built-in
surge protector, which supports
the surge protection capability of
the differential mode of 10 kA and
the common mode of 15 kA
- 48V DC
Single Cabinet
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 47
- 48V Cabinet Power Module --- DCDU-01 Board
Name Label Description
Power input
wiring terminal
NEG(-) -48 V NEG input wiring terminal
RTN(+) -48 V RTN input wiring terminal
Power output port SPARE2, SPARE1,
BBU, FAN, and RFU5-
RFU0
RFU0 to RFU5 supplying power to six WRFUs
BBU supplying power to the BBU
FAN supplying power to the FAN
SPARE1 and SPARE2 reserved
Power switch SPARE2, SPARE1,
BBU, FAN, and RFU5-
RFU0
RFU0 to RFU5 controlling the ON/OFF of the current of
six WRFUs
BBU controlling the ON/OFF of the current of the BBU
FAN controlling the ON/OFF of the current of the FAN
SPARE1 and SPARE2 controlling the ON/OF of the
current on the SPARE1 and SPARE2 power output ports
Alarm output port SPD ALM DUDU-01 dry contact alarm output port
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 48
+24V Power Subrack --- PSU (DC/DC) Board
+ 24V DC Single Cabinet
Function
Converting +24 V DC power to -48 V DC power and leading the -48 V DC power
to the DCDU
Monitoring alarms related to module faults ,alarms related to module protection
and power out-of-position alarm
(1) Power running LED
(2) Protection LED
(3) Fault LED
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 49
220V AC Power Subrack --- PSU(AC/DC) Board
(1) Power running LED
(2) Protection LED
(3) Fault LED
220V AC Single Cabinet
Function
The power subrack consists of the PMU, PSU (AC/DC) and the wiring unit of the
power subrack (220 V).
The power subrack (AC/DC) converts the 220 V AC power to the -48 V DC power.
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 50
220V AC Power Subrack --- PSU(AC/DC) Board
LED Color Status Meaning
Power
running
LED
Green On
Normal
Off
There are faults (such as no AC input, or overvoltage and
undervoltage of AC input) on the mains, or the PSU has no output.
Protection
LED
Yellow Off
Normal
On
Temperature pre-alarm or fan pre-alarm
Fault LED Red Off
Normal, or the PSU has no output because of faults (such as no AC
input, or overvoltage and undervoltage of AC input) on the mains.
On
There is no output because of output overvoltage shutdown, fan
fault, overtemperature shutdown, remote shutdown, or internal
problems of the PSU.
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 51
220V AC Power Subrack --- PMU Board
The power and environment monitoring unit (PMU) is the unit for monitoring the
power and the environment. The PMU provides perfect power system management,
power distribution detection, and alarm report functions.
(1) LEDs (2) Power supply
test ports
(3) RS232/RS422 port (4) Battery control
switches
(5) COM port
(1) Backplane port (2) DIP switch
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 52
220V AC Power Subrack --- PMU Board
Identifier Color Status Meaning
RUN Green On for 1 second and
off for 1 second
The module is functional, and the communication with the
main control unit is normal.
On for 0.125 second
and off for 0.125
second
The module runs normally but the communication with the
main control unit fails.
If the PMU does not communicate with the main control unit
for one minute, the communication fails. In this situation, the
RUN LED blinks four times every second.
On/Off The PMU is faulty (not in the power-on self-check state).
ALM Red On The following alarms are reported:
Mains overvoltage or undervoltage alarm
Busbar overvoltage or undervoltage alarm
Power module alarm
Load shutdown alarm
Off No alarm is generated.
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 53
220V AC Power Subrack --- PMU Board
Port Purpose
RS232/RS422 port Communicating with the main control unit
Battery control
switch
The battery control switch has two control ports ON and OFF, which are
used for powering on and off the battery.
Press and hold the port ON for 5s to 10s until the battery is powered on.
Press and hold the port OFF for 5s to 10s until the battery is powered off.
CAUTION:
You need to insert a small round bar into the hole when you operate the
battery control switch. When you hear a crack, the battery is powered on or
off.
To operate the battery control switch on the front panel of the PMU, insert
a small round pole into the hole.
Power supply test
port
Two power supply test holes -48 V and 0 V are available for measuring
power voltages through an ordinary multimeter.
COM port Connecting the external signal transfer board
Backplane port Connecting the backplane
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 54
220V AC Power Subrack --- PMU Board
DIP Switch: The DIP switch is
located on the rear panel of the
PMU. The DIP switch has eight
bits, which are set to OFF before
delivery.
Bit 3 Bit 2 Bit 1 Bit 0 Monitoring Address
0 0 0 0 0000
0 0 0 1 0001
0 0 1 0 0010
0 0 1 1 0011
0 1 0 0 0100
0 1 0 1 0101
0 1 1 0 0110
0 1 1 1 0111
1 0 0 0 1000
1 0 0 1 1001
1 0 1 0 1010
1 0 1 1 1011
1 1 0 0 1100
1 1 0 1 1101
1 1 1 0 1110
1 1 1 1 1111
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 55
FAN Unit
The FAN unit refers to the fan box. The FAN unit provides the functions of ventilation
and heat dissipation for cabinets. One FAN unit has four independent fans.
Type Label Connector Type Description
Power port -48 V 3V3 power connector Introducing the -48 V
DC power
Temperature sensor port SENSOR RJ45 connector Connecting the
external temperature
sensor
Communication port COM OUT RJ45 connector Cascading the lower-
level FAN module
COM IN RJ45 connector Connecting the main
control unit
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 56
Chapter 2 BTS3900 Hardware Structure
Section 1 BTS3900 Introduction
Section 2 BBU Modules Structure
Section 3 RF Modules Structure
Section 4 Power Modules Structure
Section 5 BTS3900 Cables
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 57
BBU3900 Cable Connection
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 58
Cables --- PGND Cable
PGND Cable
OT terminal
Name Color Cross-Sectional Area
PGND cable of the
BTS3900 WCDMA cabinet
Green and yellow The cross-sectional area of a wire is 25
mm
2
.
PGND cable of the DCDU Green and yellow The cross-sectional area of a wire is 6
mm
2
.
PGND cable for the SLPU Green and yellow The cross-sectional area of a wire is 6
mm
2
.
Front door PGND cable Green and yellow The cross-sectional area of a wire is 6
mm
2
.
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 59
Cables --- Power Cable
Power Cable Between the DCDU,BBU,FAN and WRFU
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 60
Cables --- Transmission Cable
E1 Cable
FE Surge Protection Transfer Cable
E1 Surge Protection Transfer Cable

FE Cable
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 61
Cables --- CPRI Cable
This describes the CPRI electrical cable. It helps to implement high speed
communication between the BBU3900 and the WRFU.
Appearance : The CPRI electrical cable is an SFP high speed transmission
cable that has a SFP200 male connector at each end.
One End The Other End
CPRI port on the WBBP CPR10 port on the WRFU
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 62
Chapter 1 NodeB Overview
Chapter 2 BTS3900 Hardware Structure
Chapter 3 BTS3900 Typical Configuration
HUAWEI TECHNOLOGIES CO., LTD. All rights reserved
Page 63
Configuration Types of the BTS3900
The BTS3900 supports omni-directional, 2-sector, 3-sector, and 6-sector
configurations. It also supports smooth capacity expansion from 1x1 to 3x8.
This part illustrates the configuration type of the BTS3900 by taking the WBBPa
supporting three cells and the WRFU supporting the 80W/4 carrier as an example.
www.huawei.com
Thank You

Das könnte Ihnen auch gefallen