Sie sind auf Seite 1von 5

Rules and Regulations for the Construction and Classification of Steel Ships - 2014

Page 3 of 14
___________________________________________________________________________________
Indian Register of Shipping
Secti on 3
Equi pment Specificati on
3.1 Equipment number
3.1.1 The equipment number, EN, on which the
requirements of equipment are based is to be
calculated as follows :-
EN =K.ENc
where,
ENc =
2/3
+2BH +0.1A
=moulded displacement, [t], to the summer
load water line
H =effective height, [m], from the summer load
waterline to the top of the uppermost
deckhouse, to be measured as follows:
H =a + h
i
a = distance [m] from summer load waterline
amidships to the upper deck at side
h
i
=height [m] on the centreline of each tier of
houses having a breadth greater than B/4. For
lowest tier, h
i
is to be measured at centre line
from upper deck, or from a notional deck line
where there is a local discontinuity in the upper
deck.
A = area [m
2
] in profile view of the hull,
superstructures and houses above the summer
load waterline, which is within the Rule length of
the vessel. Houses of breadth less than B/4 are
to be disregarded.
In the calculation of H and A, sheer and trim are
to be ignored.
Parts of windscreens or bulwarks which are
more than 1.5[m] in height are to be regarded as
parts of houses when determining H and A. The
height of the hatch coamings and that of any
deck cargo, such as containers, may be
disregarded.
'K' is a factor depending upon the type of vessel
and service notation as given below:
For fishing vessels,
K =1.00
For other vessels,
K =1.00 for vessels of Unrestricted Service.
K =0.85 for vessels of Coastal Service
K = 0.775 for vessels of Restricted Water
Service.
K =0.50 for vessels of Sheltered Water Service.
3.1.2 For a barge rigidly connected to a push tug
the equipment number is to be calculated for the
combination regarded as one unit.
3.1.3 For tugs, while determining the equipment
number EN, the term '2BH' in Sec.3.1.1 may be
substituted by 2(aB + h
i
b
i
) where b
i
is the
breadth, [m], of the widest superstructure or
deckhouse of each tier having a breadth greater
than B/4.
3.2 Equipment
3.2.1 For fishing vessels the equipment is to be
in accordance with the requirements given in
Table 3.2.1 using EN as calculated in 3.1.
3.2.2 For other vessels the equipment is to be in
accordance with the requirements given in Table
3.2.2 using EN as calculated in 3.1.
3.2.3 The two bower anchors in Table 3.2.1 and
Table 3.2.2 are to be connected to their cables
and positioned onboard ready for use. The total
length of chain is to be divided in approximately
equal parts between the two bower anchors.
3.2.4 For tugs the particulars of towlines are to
be based upon the maximum bollard pull and
the intended duty of the vessel. However, in no
case the breaking strength of the towline is to be
less than twice the maximum bollard pull.
3.2.5 For offshore supply vessels the length and
the diameter of chain cable is to be based on an
equipment letter two steps higher than that
corresponding to the EN of the vessel. Towline
is to be as per 1.1.2
3.2.6 For unmanned barges and pontoons of
length "L" less than 30 [m] no anchor need be
provided.
Where length "L" is greater than or equal to 30
[m] only one anchor of the tabular weight need
be provided. The attached chain cable is to be
of the tabular diameter and 2 L [m] in length.
Chapter 15 Part 3
Page 4 of 14 Anchoring and Mooring Equipment
Indian Register of Shipping
Two mooring lines of tabular breaking strength
are to be provided where the length 'L' is less
than 65 [m], otherwise three mooring lines are to
be provided. The length of each mooring line is
not be less than the greater of 2L [m] or 80 [m].
For unmanned barges and pontoons where the
letter 'L' is not intended to be included in the
character of classification only mooring lines of
adequate length and strength need be provided.
3.2.7 For vessels of length less than 30 [m] the
anchor chains may be replaced by wire ropes of
equal strength. For vessels of length between
30 [m] and 40 [m] one chain cable may be
replaced by wire rope of equal strength provided
normal chain cable is maintained for the second
line. For fishing vessels, wire ropes of trawl
winches complying with the above may be used
as anchor cables.
When wire ropes are substituted for anchor
chains the following should be complied with :-
i) The length of ropes should be at least
1.5 times the corresponding tabular
length of chain.
ii) A short length of chain shall be fitted
between the anchor and the wire rope.
The length of the cable need be the
smaller of 12.5 [m] and the distance
between the anchor in stowed position
and the winch.
Tabl e 3.2.1 : Equi pment f or fishing vessel s
EN
Equi p
ment
l etter
Stockless Bower
Anchors
Stud-Li nk Chai n Cabl es Moori ng Lines (Recommendation)
Number
Mass per
anchor
[kg]
Total
l ength
[m]
Diameter and chain
grade
Steel or natural fibre ropes
CC1
[mm]
CC2
[mm]
Number
Length
[m]
Breaki ng
strength
[kN]
30 & 40 Aof1 2 80 165 11 2 50 29
>40 & 50 Aof2 2 100 192.5 11 2 60 29
>50 & 60 Af1 2 120 192.5 12.5 2 60 34
>60 & 70 Af2 2 140 192.5 12.5 2 80 34
>70 & 80 Bf1 2 160 220 14 12.5 2 100 37
>80 & 90 Bf2 2 180 220 14 12.5 2 100 37
>90 & 100 Cf1 2 210 220 16 14 2 110 39
>100 & 110 Cf2 2 240 220 16 14 2 110 44
>110 & 120 Df1 2 270 247.5 17.5 16 2 110 44
>120 & 130 Df2 2 300 247.5 17.5 16 2 110 49
>130 & 140 Ef1 2 340 275 19 17.5 2 120 49
>140 & 150 Ef2 2 390 275 19 17.5 2 120 49
>150 & 175 Ff 2 480 275 22 19 2 120 54
>175 & 205 Gf 2 570 302.5 24 20.5 2 120 59
>205 & 240 Hf 2 660 302.5 26 22 2 120 64
>240 & 280 If 2 780 330 28 24 3 120 69
>280 & 320 J f 2 900 357.5 30 26 3 140 74
>320 & 360 Kf 2 1020 357.5 32 28 3 140 78
>360 & 400 Lf 2 1140 385 34 30 3 140 88
>400 & 450 Mf 2 1290 385 36 32 3 140 98
Rules and Regulations for the Construction and Classification of Steel Ships - 2014
Page 5 of 14
___________________________________________________________________________________
Indian Register of Shipping
Tabl e 3.2.1 : (Contd.)
EN
Equi p
ment
l etter
Stockless Bower
Anchors
Stud-Li nk Chai n Cabl es Moori ng Lines (Recommendation)
Number
Mass per
anchor
[kg]
Total
l ength
[m]
Diameter and chain
grade
Steel or natural fibre ropes
CC1
[mm]
CC2
[mm]
Number
Length
[m]
Breaki ng
strength
[kN]
>450 & 500 Nf 2 1440 412.5 38 34 3 140 108
>500 & 550 Of 2 1590 412.5 40 34 4 160 123
>550 & 600 Pf 2 1740 440 42 36 4 160 132
>600 & 660 QF 2 1920 440 44 38 4 160 147
>660 & 720 Rf 2 2100 440 46 40 4 160 157
Tabl e 3.2.2 : Equi pment f or vessel s excl udi ng fi shi ng vessel s
EN
Equi
pme
nt
letter
Stockless
bower anchors
Stud-link chai n cables for bower
anchors
Towline
(Recommendati
on)
Mooring l ines
1)
Total
length
[m]
Diameter and grade Steel or natural fibre ropes
Num
ber
Mass
per
anchor
[kg]
CC1
[mm]
CC2
[mm]
CC3
[mm]
Mi n.
length
[m]
Mi n.
breaki ng
strength
[kN]
Num
ber
Length
of each
[m]
Min.
break-
ing
stren-
gth
[kN]
50 & 70 A 2 180 220 14 12.5 180 98 3 80 34
>70 & 90 B 2 240 220 16 14 180 98 3 100 37
>90 & 110 C 2 300 247.5 17.5 16 180 98 3 110 39
>110 & 130 D 2 360 247.5 19 17.5 180 98 3 110 44
>130 & 150 E 2 420 275 20.5 17.5 180 98 3 120 49
>150 & 175 F 2 480 275 22 19 180 98 3 120 54
>175 & 205 G 2 570 302.5 24 20.5 180 112 3 120 59
>205 & 240 H 2 660 302.5 26 22 20.5 180 129 4 120 64
>240 & 280 I 2 780 330 28 24 22 180 150 4 120 69
>280 & 320 J 2 900 357.5 30 26 24 180 174 4 140 74
>320 & 360 K 2 1020 357.5 32 28 24 180 207 4 140 78
>360 & 400 L 2 1140 385 34 30 26 180 224 4 140 88
>400 & 450 M 2 1290 385 36 32 28 180 250 4 140 98
>450 & 500 N 2 1440 412.5 38 34 30 180 277 4 140 108
>500 & 550 O 2 1590 412.5 40 34 30 190 306 4 160 123
>550 & 600 P 2 1740 440 42 36 32 190 338 4 160 132
>600 & 660 Q 2 1920 440 44 38 34 190 371 4 160 147
>660 & 720 R 2 2100 440 46 40 36 190 406 4 160 157
>720 & 780 S 2 2280 467.5 48 42 36 190 441 4 170 172
>780 & 840 T 2 2460 467.5 50 44 38 190 480 4 170 186
>840 & 910 U 2 2640 467.5 52 46 40 190 518 4 170 201
>910 & 980 V 2 2850 495 54 48 42 190 559 4 170 216
>980 & 1060 W 2 3060 495 56 50 44 200 603 4 180 230
>1060 & 1140 X 2 3300 495 58 50 46 200 647 4 180 250
Chapter 15 Part 3
Page 6 of 14 Anchoring and Mooring Equipment
Indian Register of Shipping
Tabl e 3.2.2 (Contd.)
EN
Equi
pme
nt
letter
Stockl ess
bower anchors
Stud-link chai n cables for bower
anchors
Towline
(Recommendati
on)
Mooring l ines
1)
Total
length
[m]
Diameter and grade Steel or natural fibre ropes
Num
ber
Mass
per
anchor
[kg]
CC1
[mm]
CC2
[mm]
CC3
[mm]
Mi n.
length
[m]
Mi n.
breaking
strength
[kN]
Num
ber
Length
of each
[m]
Mi n.
break-
ing
stren-
gth
[kN]
>1140 & 1220 Y 2 3540 522.5 60 52 46 200 691 4 180 270
>1220 & 1300 Z 2 3780 522.5 62 54 48 200 738 4 180 284
>1300 & 1390 A+ 2 4050 522.5 64 56 50 200 786 4 180 309
>1390 & 1480 B+ 2 4320 550 66 58 50 200 836 4 180 324
>1480 & 1570 C+ 2 4590 550 68 60 52 220 888 5 190 324
>1570 & 1670 D+ 2 4890 550 70 62 54 220 941 5 190 333
>1670 & 1790 E+ 2 5250 577.5 73 64 56 220 1024 5 190 353
>1790 & 1930 F+ 2 5610 577.5 76 66 58 220 1109 5 190 378
>1930 & 2080 G+ 2 6000 577.5 78 68 60 220 1168 5 190 402
>2080 & 2230 H+ 2 6450 605 81 70 62 240 1259 5 200 422
>2230 & 2380 I+ 2 6900 605 84 73 64 240 1356 5 200 451
>2380 & 2530 J + 2 7350 605 87 76 66 240 1453 5 200 480
>2530 & 2700 K+ 2 7800 632.5 90 78 68 260 1471 6 200 480
>2700 & 2870 L+ 2 8300 632.5 92 81 70 260 1471 6 200 490
>2870 & 3040 M+ 2 8700 632.5 95 84 73 260 1471 6 200 500
>3040 & 3210 N+ 2 9300 660 97 84 76 280 1471 6 200 520
>3210 & 3400 O+ 2 9900 660 100 87 78 280 1471 6 200 554
>3400 & 3600 P+ 2 10500 660 102 90 78 280 1471 6 200 588
>3600 & 3800 Q+ 2 11100 687.5 105 92 81 300 1471 6 200 618
>3800 & 4000 R+ 2 11700 687.5 107 95 84 300 1471 6 200 647
>4000 & 4200 S+ 2 12300 687.5 111 97 87 300 1471 7 200 647
>4200 & 4400 T+ 2 12900 715 114 100 87 300 1471 7 200 657
>4400 & 4600 U+ 2 13500 715 117 102 90 300 1471 7 200 667
>4600 & 4800 V+ 2 14100 715 120 105 92 300 1471 7 200 677
>4800 & 5000 W+ 2 14700 742.5 122 107 95 300 1471 7 200 686
>5000 & 5200 X+ 2 15400 742.5 124 111 97 300 1471 8 200 686
>5200 & 5500 Y+ 2 16100 742.5 127 111 97 300 1471 8 200 696
>5500 & 5800 Z+ 2 16900 742.5 130 114 100 300 1471 8 200 706
>5800 & 6100 A* 2 17800 742.5 132 117 102 300 1471 8 200 706
>6100 & 6500 B* 2 18800 742.5 137 120 107 300 1471 9 200 716
>6500 & 6900 C* 2 20000 770 124 111 300 1471 9 200 726
>6900 & 7400 D* 2 21500 770 127 114 300 1471 10 200 726
>7400 & 7900 E* 2 23000 770 132 117 300 1471 11 200 726
>7900 & 8400 F* 2 24500 770 137 122 300 1471 11 200 735
>8400 & 8900 G* 2 26000 770 142 127 300 1471 12 200 735
>8900 & 9400 H* 2 27500 770 147 132 300 1471 13 200 735
>9400 & 10000 I* 2 29000 770 152 132 300 1471 14 200 735
>10000 & 10700 J * 2 31000 770 137 15 200 735
>10700 & 11500 K* 2 33000 770 142 16 200 735
>1480 & 1570 C+ 2 4590 550 68 60 52 220 888 5 190 324
Rules and Regulations for the Construction and Classification of Steel Ships - 2014
Page 7 of 14
___________________________________________________________________________________
Indian Register of Shipping
Tabl e 3.2.2 (Contd.)
EN
Equi
pme
nt
letter
Stockless
bower anchors
Stud-link chai n cables for bower
anchors
Towline
(Recommendati
on)
Mooring l ines
1)
Total
length
[m]
Diameter and grade Steel or natural fibre ropes
Num
ber
Mass
per
anchor
[kg]
CC1
[mm]
CC2
[mm]
CC3
[mm]
Mi n.
length
[m]
Mi n.
breaki ng
strength
[kN]
Num
ber
Length
of each
[m]
Min.
break-
ing
stren-
gth
[kN]
>11500 & 12400 L* 2 35500 770 147 17 200 735
>12400 & 13400 M* 2 38500 770 152 18 200 735
>13400 & 14600 N* 2 42000 770 157 19 200 735
>14600 & 16000 O* 2 46000 770 162 21 200 735
1) For individual mooring lines with required breaking force above 490 [kN] according to the table, the required strength may be
reduced by the corresponding increase of the number of mooring lines and vice versa, provided that the total of all mooring lines
on board is not less than the Rule value. However, the number of mooring lines is not to be less than 6, and no line is to have a
breaking force less than 490 [kN].
Secti on 4
Anchors
4.1 General
4.1.1 Anchors are to be of an approved design.
4.1.2 The mass of each bower anchor as
required in Sec.3 is for anchors of equal mass.
The masses of individual anchors may vary by
7 per cent of the tabular masses, provided that
the total mass of the anchors is not less than
would have been required for anchors of equal
mass.
4.1.3 The mass of the head, including pins and
fittings, of an ordinary stockless anchor is not to
be less than 60 per cent of the total mass of the
anchor.
4.1.4 The mass 'ex stock' of stocked bower or
stream anchors is not to be less than 80 per
cent of the tabular mass of ordinary stockless
bower anchors. The mass of the stock is to be
25 per cent of the total mass of the anchor
including the shackle etc. but excluding the
stock.
4.1.5 When anchors of a design approved for
the designation 'High Holding Power' or 'Super
High Holding Power' are used as bower
anchors, the mass of each such anchor may be
75 percent or 50 percent respectively of the
tabular mass of ordinary stockless bower
anchors.
4.1.6 Anchor shackles are to be of a design and
material suitable to the service for which the
anchor is intended.
4.2 High Holding Power (HHP) anchors
4.2.1 Designs of H.H.P. anchors are to be
approved for the designation.
H.H.P. anchors are to be designed for effective
hold of the sea bed irrespective of the angle or
position at which they first settle on the sea bed
after dropping from a normal type of hawse pipe.
In case of doubt a demonstration of these
abilities may be required. The designs are to be
tested on sea bed to show that they have a
holding down power per unit of mass at least
twice that of approved ordinary stockless
anchor.
4.2.2 If approval is sought for a range of anchor
sizes, at least two sizes are to be tested. The
mass of the larger anchor to be tested is not to
be less than one-tenth of that of the largest
anchor of which approval is sought. The smaller
of the two anchors to be tested is to have a
mass not less than one-tenth of that of the
larger.

Das könnte Ihnen auch gefallen