Hardware Operating panel Measurement Sensors for mains and generator frequency 50 or 60 Hz, can be set to any value between 40 and 70 Hz. Sensors for mains and generator voltage, 3-phase, 100-500V, Accuracy class 1. Generator current sensors 3-phase, Accuracy class 1. I Nom 5 A: measuring range 0,1 15 A, can be set in increments of 20 mA. 1 battery voltage monitor 1 synchronisation unit with integrated check synchroniser Digital outputs 3 relay outputs (n.o.), freely parameterisable, 24V 1A Analogue in-/output 4 analogue inputs, can be equipped for: Sensors PT 100 / PT1000, 0-20 mA, 0-10V DC,NiCr-Ni type: K Temperature and pressure sensor from VDO, 2 analogue outputs 0 20 mA or 0 10 V Serial interfaces Parameters can be set via a bre optics or USB interface CAN bus interface to common control, FBED, CAN bus interface to engine management Relay card KRK-12 Equipped with: 14 terminals for alarm contacts, of which 9 relays can be parameterised 1 input for pick-up 1 input for alternator D+ with pre-excitation for AC alternators, 14 general control inputs, 12 relays, contact load: 120 V AC, 0,5 A / 24V DC 1 A enhancable with relay card KRK-27 Technical Data Operating panel KEA Device for panel mounting, with KRK-12 or KRK-27 Dimensions (WxHxD): 260 x 170 x 125 mm, Weight: approx. 2,6 kg, any installation position, Protection type (built-in) IP 44 Relay card KRK-12 Relay card mounted in operating panel, Dimensions (WxHxD): 300 x 45 x 90 mm (with multiple adapter), Weight: approx. 0,3 kg, any installation position, Protection type (built-in) IP 00 Relay card KRK-27 Relay card mounted in operating panel, Dimensions (WxHxD): 300 x 45 x 90 mm, Weight: approx. 0,5 kg, any installation position, Protection type (built-in) IP 00 General Ambient temperature: Storage-20C ... +70C, Operation 0C ... +55C, Supply voltage switchable 9-12-15V or 14-24-35V DC, Standards/regulations: DIN EN 501780, VDS 2100-22. General options GSM Modem with antenna and cable 3 m for remote control Connection to other systems, for example via Probus DP, Modbus or Ethernet Event recorder with protocol and fault printout via an RS 232 interface Additional relay card KRK-27: 27 relays on KRK-27, of which 23 can be parameterised, contact load: max. 250V AC, 1 A CAN bus module (DIO and analogue) (in preparation) General The compact automatic control unit KEA 251 ERSY is used in emer- gency power supply plants with/without overlapping synchronisation. Fault signals, counter readings, analogue values and status signals are visible on a display. 4 LED indicators can be used for the display of addi- tional operation indicators. An additional relay card with 12 or 27 relays is available for this control unit. The output relay function and the parameters can be set with a PC. As the KEA 251 is the same size and is attached in the same manner as its predecessors, it can be exchanged without difculty. The automatic control unit is simple to operate as it is operated by using the keys on the control panel. Alfred Kuhse GmbH Tel.: +49 4171 / 798-0 E-Mail: kuhse@kuhse.de Subject to modifcation An der Kleinbahn 39 Fax: +49 4171 / 798-117 www.kuhse.de Datenblatt_KEA251ERSY_uk01 21423 Winsen, Germany State: 02/2014