0 Bewertungen0% fanden dieses Dokument nützlich (0 Abstimmungen)
31 Ansichten4 Seiten
TopStone Modular Countertop Systems is designed to suit 24" deep base cabinets. When installed, a kit will give a 1" overhang bull-nosed edge fnish with a total depth of 25" the unique design also allows for 3" increments in length and meets the North American cabinet standards.
TopStone Modular Countertop Systems is designed to suit 24" deep base cabinets. When installed, a kit will give a 1" overhang bull-nosed edge fnish with a total depth of 25" the unique design also allows for 3" increments in length and meets the North American cabinet standards.
TopStone Modular Countertop Systems is designed to suit 24" deep base cabinets. When installed, a kit will give a 1" overhang bull-nosed edge fnish with a total depth of 25" the unique design also allows for 3" increments in length and meets the North American cabinet standards.
on the next page and select the correct type and number of kits for your project. If you would like to download our TopStone Planning Guide to assist you with your kitchen layout, please go to www.mydiygenius.com. Installation Instructions Toll Free Phone/Sans frais : 1-866-843-8453 Email/Courriel : info@halsteadintl.com Web/Web : http://www.mydiygenius.com COUNTERTOP SYSTEMS SYSTMES DE COMPTOIR Congratulations on purchasing a TopStone Countertop Systems Modular Kitchen Tiles Set. TopStone Modular Countertop Systems is designed to suit 24 deep base cabinets. When installed, a kit will give a 1 overhang bull-nosed edge fnish with a total depth of 25. The unique design also allows for 3 increments in length and meets the North American cabinet standards. Please read the instructions carefully and familiarize yourself with components in the packing list attached to the end of these instructions or on the outside of each kit prior to installation. Prior to installation, a dry run of the countertop components is recommended to ensure you have the required sets to complete the project. Marking for sink cut-out should be done during the dry run and the sub surface material should be cut out according to the sink recommendations or template. Tools required for installation: Straight edge Carpenter's level Tri-square 1/4 x 3/8 x 1/4 Square-Notch Trowel Drill 1 Spade Bit Diamond or Carbide tip hole saw used for drilling faucet holes in granite. (Follow faucet manufacturer's recommendations for drill bit size) Granite Tile Saw (wet or dry). Might not be required depending on your countertop layout. Jig Saw (used for cutting sink sub-straight material) Note: The following information is a guideline only and TopStone is not responsible for damages caused during installation. 1. Base Preparation: Cabinets on which the countertop will be installed should be frmly fxed in place. Use a tri-square to ensure the cabinet corners are square and level the surface using a carpenter's level to ensure the top surface of the cabinets are all level. If you are using your existing cabinets and you fnd they are not level, you can add shims under the plywood sub-straight to correct the problem. IMPORTANT! When using the TopStone Modular Kitchen Tile Countertop System, DO NOT exceed the 3/4 overall sub-straight decking material thick- ness. The TopStone tiles have 3/4 drop-down on the edge detail build up. 2. Sub-Surface Preparation: Use either 3/4 plywood or 1/2 plywood with 1/4 backer board material. Cut to suit the cabinet size and secure it to the cabinet frame using screws. Plywood should be fush to front / back / sides of the cabinet. You may overhang the board on the sides of your countertop for extended length, but do not exceed more than 6 overhang. Remove all debris and rough sand surface. Wipe or vacuum wood dust from surface. 3. Cut-out for Undermount or Drop-in Sinks: Locate the center placement for your undermount or drop-in sink. Be sure you do not have any cabinet obstruction where you plan to place your sink. Be sure to follow the sink manufacturer's installation instructions for cutting out your countertop. These instructions will be different for an undermount installation vs. a drop-in installation. It is recommended that you perform a dry run with all TopStone tiles prior to installation. NOTE: Your TopStone Sink Kit has been polished on the inside edges of your sink kit tiles. This allows for a finished look when using an undermount sink application/installation. IMPORTANT! Your TopStone Modular Kitchen Tiles are designed to be installed with no spacing between each tile. We do not recommend using tile spacers as this will throw off your kitchen tile layout and might require additional tile cutting. 4. Modular Countertop Installation: NOTE: See Step #5 for backsplash prep before installing countertop tiles. The following two methods can be employed for installation: a. Installation Using Thin-Set: Clean debris, grease etc. from tiles and sub-straight material. Using the 1/4 x 3/8 x1/4 trowel, start applying the thin-set mortar with latex additive on the fnished sub-straight and start setting with front edge tiles of the countertop. Be sure to follow mortar manufacturer's instructions. It is also recommended that you spread only as much mortar as you can comfortably work with in setting tiles. You do not want mortar to set up before you have a chance to lay any countertop tiles. Press the tiles gently on the thin-set with lateral movement for 100% coverage and align the face using a straight edge. Use a carpenter's level to check the level of the surface. In case of L or U shaped countertops, start with laying the inside corner tiles frst and go sideways along the front edge until the edges are covered. Start setting the back tiles in the same way as above. Use a carpenter's level to check the level of the surface and make any adjustments before thin-set hardens. Clean the surface with a moist cloth. Allow for 24 hours cure time. Vertex Services Limited, 2011 MKT Topstone Installation Gide_MKT Installation Gide 11/16/11 3:27 PM Page 1 b. Installation Using Adhesive: Apply a 1/8 thick epoxy with trowel on the fnished sub-straight (follow the instruction on application of epoxy from the manufacturer) and start setting the front edge tiles. Press the tiles gently into the epoxy with lateral movement for 100% coverage and align the face using a straight edge. Use a carpenter's level to check the level of the surface. In case of L or U shaped countertops, start with laying the inside corner tiles frst and go sideways on the front edge until the edges are covered. Start setting the back tiles in the same manner as above (see epoxy manufacturer's instructions for proper curing time). Use a carpenter's level to check the level of the surface and make any adjustments before epoxy hardens. Clean the surface with a moist cloth. Use clear epoxy or blend for color matching of tiles. 5. Installing Back Splash: Before laying any of the feld tiles, be sure to sand the wall surface where backsplash will be positioned on the countertop. Clean the wall to ensure that it is free of dust. Apply an 1/8 layer of thin-set mortar with latex additive or adhesive on the back of the backsplash tile using a trowel and lay it against the wall aligned with its respective tile. Align the grout lines to the countertop tiles and check the level with a straight edge. Use a carpenter's level to check the level of the surface. Start setting the inside corner frst and move outwards. Clean surface with clean moist cloth and allow to cure for 24 hours. 6. Grouting: If you prefer, you can fll all tile seams with a matching fexible grout adhesive. Clean the surface at the joints and grout lines to remove excessive material just as you would when installing tile. Follow grout manufacturer's instructions for proper installation. 7. Undermount or Drop-in Sink Installation: Once your TopStone Countertop has had the approximate 48 hours dry time, you may begin installing your sink. Please follow sink manufacturer installation instructions. CAUTION: Never use plumber's putty or any other oil- based sealant on granite counters. Clear sealant is recommended. We recommend a Phenoseal or DAP sealant as other silicone sealers can stain and blemish the looks of the countertop tiles. 8. Sealing the Countertop: Your TopStone Modular Kitchen Tiles have been pre-sealed at the factory, however it is recommended after completion of installation, that you re-seal your countertop again for added protection against water absorption. Again, allow the installation to dry completely for 48 hours minimum. Apply the sealer on the top surface including the grout lines generously and allow it to absorb for 10 minutes and wipe off the excess from the surface (follow sealer manufacturer recommendations for application). Apply a second coat to protect against bacteria growth. This will also protect the seams against bacteria growth. Sealer should be applied every 1 to 2 years (depending on the usage and wear of the countertop) for preventative maintenance. Follow sealer recommendations. Use water-based sealer that resists water, oil and acid-based contaminants. This will simplify maintenance and does not change the appearance. Wear depends on the area of work, frequency of cleaning and type of maintenance products used. NOTE: TopStone is not responsible for any damages or breakages resulting from the installation carried out by individuals. End Set Qty Description Size Code 1 Rear End Tile 13 x 12 x RET 1 Front End Tile 13 x 13 x FET 1 Rear Tile 12 x 12 x RT 1 Front Tile 12 x 13 x FT 1 Left End Back Splash 12 x 4 x LEBS 1 Right End Back Splash 12 x 4 x REBS 1 Back Splash 12 x 4 x BS Intermediate Set A Qty Description Size Code 2 Front Tile 12" x 13" x FT 2 Rear Tile 12" x 12" x RT 1 Front Filler Tile 6 6 x 13 x FFT6 1 Rear Filler Tile 6 6 x 12 x RFT6 1 Front Filler Tile 3 3 x 13 x FFT3 1 Rear Filler Tile 3 3 x 12 x RFT3 2 Back Splash 12" x 4" x BS 1 Filler Back Splash 6 6 x 4 x FBS6 1 Filler Back Splash 3 3 x 4 x FBS3 Intermediate Set B Qty Description Size Code 2 Front Tile 12 x 13 x FT 2 Rear Tile 12 x 12 x RT 2 Back Splash 12 x 4 x BS Intermediate Set C Qty Description Size Code 4 Front Tile 12 x 13 x FT Inside Corner Set 90 Qty Description Size Code Box 1 Front Left Corner Tile 12" x 13" x " FLCT Box A 1 Front Right Corner Tile 12 x 13 x FRCT Box B 6 Rear Tile 12 x 12 x RT 3 Box A; 3 Box B 1 Left Corner Back Splash 12 x 4 x LCBS Box B 1 Right Corner Back Splash 12 x 4 x RCBS Box B 4 Back Splash 12 x 4 x BS 3 Box A; 1 Box B Inside Corner Set 45 Qty Description Size Code 1 Front Center Corner Tile 17 x 45 x FCCT 5 Rear Tile 12 x 12 x RT 2 Back Splash 12 x 4 x BS Sink Set Qty Description Size Code 1 Sink Corner Rear Left 12" x 12" x " SCRL 1 Sink Corner Rear Right 12" x 12" x " SCRR 1 Sink Corner Front Tile Left 12" x 13" x " SCFTL 1 Sink Corner Front Tile Right 12" x 13" x " SCFTR 2 Sink Kit Front Tile 12" x 3" x " SKFT 2 Sink Kit Rear Tile 12" x 4" x " SKRT 4 Back Splash 12" x 4" x " BS KIT DETAILS Note: Inside Corner Set 90 includes Box A and Box B, sold separately Vertex Services Limited, 2011 MKT Topstone Installation Gide_MKT Installation Gide 11/16/11 3:27 PM Page 2 Flicitations pour votre achat de carreaux modulaires de cuisine pour systmes de comptoirs TopStone. Les systmes de comptoirs modulaires TopStone sont conus pour tre installs sur des bases d'armoire ayant une profondeur de 61cm / 24". Une fois install, le kit aura une bordure arrondie de 2,54cm / 1" en surplomb et une profondeur totale de 63,5cm / 25". Son design unique permet galement des incrments en longueur de 7,62cm / 3", conformes aux normes de menuiserie nord-amricaines. Avant de faire l'installation, veuillez lire attentivement les instructions afn de vous familiariser avec les composantes de la liste d'emballage se trouvant la fn du guide d'instructions ou l'extrieur du carton d'emballage de chaque kit. Avant l'installation, il est recommand de faire un essai des composantes pour vous assurer davoir tous les kits ncessaires pour complter le projet. Le traage du dcoupage pour l'vier devrait tre fait durant l'essai et les matriaux sous la surface devraient tre dcoups selon les recommandations ou le gabarit venant avec l'vier. Outils requis pour l'installation : Une rgle de vrifcation Un niveau bulle Un tiers-point Une truelle dents carres de 0,63cm x 0,95cm x 0,63cm / 1/4" x 3/8" x 1/4" Une perceuse Un foret de 2,54cm / 1" 3 pointes Scie cloche en diamant ou en carbure pour percer les trous des robinets dans le granit (suivez les recommandations du fabricant pour la grandeur du foret) Scie granit ( eau ou sec) (peut ne pas tre ncessaire selon la disposition du comptoir) Scie sauteuse (pour couper les matriaux de la sous-couche de l'vier) Remarque : L'information suivante est titre de conseils seulement et TopStone ne peut tre tenu responsable de dommages survenus durant l'installation. 1. Prparation de la base : Les armoires sur lesquelles seront installs les comptoirs doivent tre fxes solidement en place. Utilisez le tiers-point et le niveau bulle pour confrmer que les coins des armoires soient querres et les surfaces des armoires niveau. Si vous utilisez des armoires dj existantes et que vous trouvez qu'elles ne sont pas niveau, vous pouvez ajouter des cales d'paisseur sous la sous-couche en contreplaqu pour corriger le problme. IMPORTANT ! Lorsque vous utilisez les carreaux modulaires de cuisine pour systmes de comptoirs TopStone, les matriaux de la sous-couche NE DOIVENT PAS excder 2 cm / 3/4" d'paisseur. La bordure des carreaux TopStone a un rebord de 2 cm / 3/4". 2. Prparation de la sous-couche : Vous pouvez utiliser un contreplaqu de 2cm / 3/4" ou un contreplaqu de 1,27cm / 1/2" et un panneau d'appui de 0,63cm / 1/4". Le couper selon la grandeur de l'armoire et l'attacher la charpente de l'armoire avec des vis. Le contreplaqu doit tre exactement de la mme grandeur l'avant, l'arrire et sur les cts de l'armoire. Si vous laissez la planche dpasser sur les cts de votre comptoir pour une plus grande surface, le surplomb ne peut excder 15cm / 6". Enlevez tous les dbris et sablez lgrement la surface. Nettoyez ou aspirez la poussire de bois laisse la surface. 3. Dcoupage pour les viers montage sous plan ou en surface : Dterminez o le centre de l'vier montage sous plan ou en surface doit tre plac. Assurez-vous qu'il n'y a aucune obstruction dans l'armoire en dessous. Veillez bien suivre les instructions du fabricant de l'vier pour le dcoupage du comptoir. Ces instructions diffreront s'il s'agit d'une installation montage sous plan ou dune installation montage en surface. Il est prfrable de faire un essai avec tous les carreaux TopStone avant de passer l'installation. REMARQUE : Les bords intrieurs des carreaux d'vier de votre kit TopStone ont t polis. Cela donne un plus beau fini lorsqu'ils sont utiliss avec vier montage sous plan. IMPORTANT ! Vos carreaux modulaires de cuisine TopStone ont t conus pour tre installs sans espacement entre les carreaux. Nous dconseillons l'utilisation de cales d'espacement, car cela affectera la disposition des carreaux et pourrait exiger des tailles de carreaux additionnelles. 4. Installation de comptoirs modulaires: REMARQUE : Revoir l'tape no 5 pour le dosseret de prparation avant d'installer vos carreaux de comptoir. Les deux mthodes d'installation suivantes peuvent tre utilises : a. Installation avec mortier : Nettoyez les dbris, graisse, etc. sur les carreaux et sur la sous-couche. l'aide dune truelle de 0,63cm x 0,95cm x 0,63cm / 1/4" x 3/8" x 1/4", appliquez une mince couche de mortier au latex sur la sous-couche et commencez installer les carreaux de la bordure avant. Assurez-vous de suivre les instructions du fabricant de mortier. Il est galement recommand d'tendre seulement la quantit de mortier avec laquelle vous tes l'aise de travailler pour installer les carreaux. Vous ne voulez pas que le mortier commence scher avant d'avoir pu installer les carreaux du comptoir. Poussez doucement les carreaux dans la couche de mortier en utilisant un mouvement latral et alignez-les en utilisant une rgle de vrifcation. Utilisez un niveau bulle pour vous assurer que la surface soit bien niveau. Pour les comptoirs en forme de L ou de U, commencez par installer les carreaux du coin intrieur et continuez le long de la partie avant jusqu' ce que la bordure soit entirement couverte. Faites de mme avec les carreaux arrires. l'aide d'un niveau bulle, assurez-vous que la surface soit niveau et, au besoin, faites les ajustements avant que le mortier ne durcisse. Nettoyez la surface avec un linge humide. Laissez scher pendant au moins 24 heures. b. Installation avec un adhsif : l'aide d'une truelle, appliquez une couche de 0,3cm / 1/8" de rsine d'poxy (suivez les instructions d'installation du fabricant) et commencez installer les carreaux de la bordure avant. Poussez doucement les carreaux dans la rsine d'poxy en utilisant un mouvement latral pour une adhrence complte et alignez-les en utilisant une rgle de vrifcation. Utilisez un niveau bulle pour vous assurer que la surface soit bien niveau. Pour les comptoirs en forme de L ou de U, commencez par installer les carreaux du coin intrieur et continuez le long de la partie avant jusqu' ce que la bordure soit entirement couverte. Faites de mme avec les carreaux arrires. Vrifez la dure de schage dans les instructions du fabricant de rsine d'poxy. l'aide d'un niveau bulle, assurez-vous que la surface soit niveau et, au besoin, faites les ajustements avant que la rsine d'poxy ne durcisse. Nettoyez la surface avec un linge humide. Utilisez une rsine transparente ou d'une couleur s'apparentant celle des carreaux. 5. Installation du dosseret : Nettoyez le mur pour enlever toute la poussire laisse en surface. l'aide de la truelle, appliquez une couche de 0,3cm / 1/8" de mortier au latex ou d'adhsif l'arrire du dosseret et collez-le sur le mur en l'alignant avec son carreau respectif. Alignez les joints de coulis avec ceux du comptoir et vrifez l'alignement avec la rgle de vrifcation. Utilisez un niveau bulle pour vous assurer que la surface soit bien niveau. Commencez l'installation par un coin intrieur et continuez vers l'extrieur. Nettoyez la surface avec un linge propre et humide et laissez scher pendant 24 heures. Diffrents kits offerts conviendront votre agencement. Vous trouverez les dtails sur les diffrents kits en la page suivante, ainsi que le nombre de kits ncessaires pour votre projet. Pour tlcharger notre Guide de planifcation TopStone pour vous aider planifer l'agencement de votre cuisine, visitez le www.mydiygenius.com. Vertex Services Limited, 2011 MKT Topstone Installation Gide_MKT Installation Gide 11/16/11 3:27 PM Page 3 6. Installation du coulis : Selon votre prfrence, vous pouvez remplir les joints entre les carreaux avec un coulis adhsif fexible assorti. Nettoyez la surface des joints et des lignes de coulis pour enlever tout excdant de matriaux, comme vous le faites lorsque vous installez des carreaux. Suivez les instructions du fabricant pour une bonne installation. 7. vier montage sous plan ou en surface Installation : Une fois que votre comptoir TopStone a sch pendant au moins 48 heures, vous pouvez commencer l'installation de votre vier. Veuillez suivre le guide d'installation du fabricant. MISE EN GARDE : Il ne faut jamais utiliser de mastic de plombier ou autre agent scellant base d'huile sur un comptoir en granit. L'utilisation d'un scellant transparent est recommande. Nous recommandons d'utiliser Phenoseal ou un scellant DAP, car les autres agents scellant en silicone pourraient tacher ou endommager la surface de votre comptoir. 8. Sceller le comptoir : Mme si vos carreaux modulaires de cuisine Topstone ont t prscells en usine, nous recommandons que vous scelliez nouveau votre comptoir une fois l'installation termine pour mieux l'impermabiliser. Ici aussi, il faut laisser l'installation scher compltement pendant au moins 48 heures. Appliquez gnreusement le scellant sur la surface et les joints de coulis, puis laissez le liquide pntrer pendant 10 minutes avant d'essuyer le surplus laiss en surface (suivez les recommandations d'application du fabricant). Appliquez une deuxime couche pour protger la surface contre la croissance de bactries. Cela permettra galement de protger les joints contre la croissance de bactries. Par mesure de prvention, un scellant doit tre rappliqu tous les 1 2 ans (selon l'usage et l'usure du comptoir). Suivez les recommandations du fabricant. Utilisez un scellant base d'eau qui rsiste l'eau, l'huile et les contaminants base d'acide. Cette opration simplifera l'entretien et n'altrera pas l'apparence. L'usure du comptoir dpend de la surface de travail, de la frquence de nettoyage et des produits utiliss. REMARQUE : TopStone n'est pas responsable des dommages ou des bris subis durant une installation faite par des particuliers. Kit D'extrmit Qt Description Grandeur Code 1 carreau extrmit arrire 30.48 cm x 33.02 cm x 1.27 cm (12 po x 13 po x 1/2 po) RET 1 carreau extrmit avant 33.02 cm x 33.02 cm x 1.27 cm (13 po x 13 po x po) FET 1 carreau arrire 30.48cm x 30.48cm x 1.27cm (12 po x 12 po x po) RT 1 carreau avant 30.48cm x 33.02cm x 1.27cm (12 po x 13 po x po) FT 1 dosseret arrire extrmit gauche 31.75cm x 10.16cm x 1.27cm (12 po x 4 po x po) LEBS 1 dosseret arrire extrmit droite 31.75cm x 10.16cm x 1.27cm (12 po x 4 po x po) REBS 1 dosseret arrire 30.48cm x 10.16cm x 1.27cm (12 po x 4 po x po) BS Kit Intermdiaire A Qt Description Grandeur Code 2 carreau avant 30.48cm x 33.02cm x 1.27cm (12 po x 13 po x po) FT 2 carreau arrire 30.48cm x 30.48cm x 1.27cm (12 po x 12 po x po) RT 1 bordure avant 7.62 cm 7.62cm x 33.02cm x 1.27cm (3 po x 13 po x po) FFT3 1 bordure arrire 7.62 cm 7.62cm x 30.48cm x 1.27cm (3 po x 12 po x po) RFT3 1 bordure avant 15.24 cm 15.24 cm x 33.02cm x 1.27cm (6 po x 13 po x po) FFT6 1 bordure arrire 15.24 cm 15.24cm x 30.48cm x 1.27cm (6 po x 12 po x po) RFT6 2 dosseret arrire 30.48cm x 10.16cm x 1.27cm (12 po x 4 po x po) BS 1 bordure de dosseret arrire 7.62 cm 7.62cm x 10.16cm x 1.27cm (3 po x 4 po x po) FBS3 1 bordure de dosseret arrire 15.24 cm 15.24cm x 10.16cm x 1.27cm (6 po x 4 po x po) FBS6 Kit Intermdiaire B Qt Description Grandeur Code 2 carreau avant 30.48cm x 33.02cm x 1.27cm (12 po x 13 po x po) FT 2 carreau arrire 30.48cm x 30.48cm x 1.27cm (12 po x 12 po x po) RT 2 dosseret arrire 30.48cm x 10.16cm x 1.27cm (12 po x 4 po x po) BS Kit Intermdiaire C Qt Description Grandeur Code 4 carreau avant 30.48cm x 33.02cm x 1.27cm (12 po x 13 po x po) FT Kit De Coin Intrieur 90 Qt Description Grandeur Code Bote 1 carreau coin avant gauche 30.48cm x 33.02cm x 1.27cm (12 po x 13 po x po) FLCT Bote A 1 carreau coin avant droit 30.48cm x 33.02cm x 1.27cm (12 po x 13 po x po) FRCT Bote B 6 carreau arrir 30.48cm x 30.48cm x 1.27cm (12 po x 12 po x po) RT 3 Bote A; 3 Bote B 1 dosseret coin arrire gauche 30.48cm x 10.16cm x 1.27cm (12 po x 4 po x po) LCBS Bote B 1 dosseret coin arrire droit 30.48cm x 10.16cm x 1.27cm (12 po x 4 po x po) RCBS Bote B 4 dosseret arrire 30.48cm x 10.16cm x 1.27cm (12 po x 4 po x po) BS 3 Bote A; 1 Bote B Note : Le kit de coin 90 comprend les botes A et B, vendu sparment Kit De Coin Intrieur 45 Qt Description Grandeur Code 1 carreau de coin central avant 43.18cm x 45 x 1.27cm (17 po x 45 x po) FCCT 5 carreau arrire 30.48cm x 30.48cm x 1.27cm (12 po x 12 po x po) RT 2 dosseret arrire 30.48cm x 10.16cm x 1.27cm (12 po x 4 po x po) BS Kit D'vier Qt Description Grandeur Code 1 coin d'vier arrire gauche 30.48cm x 30.48cm x 1.27cm (12 po x 12 po x po) SCRL 1 coin d'vier arrire droit 30.48cm x 30.48cm x 1.27cm (12 po x 12 po x po) SCRR 1 coin d'vier carreau avant gauche 30.48cm x 33.02cm x 1.27cm (12 po x 13 po x po) SCFTL 1 coin d'vier carreau avant droit 30.48cm x 33.02cm x 1.27cm (12 po x 13 po x po) SCFTR 2 kit d'vier carreau avant 30.48cm x 8.89 cm x 1.27cm (12 po x 3 po x po) SKFT 2 kit d'vier carreau arrire 30.48cm x 12.06cm x 1.27cm (12 po x 4 po x po) SKRT 4 dosseret arrire 30.48cm x 10.16cm x 1.27cm (12 po x 4 po x po) BS LES DTAILS DES KITS Vertex Services Limited, 2011 MKT Topstone Installation Gide_MKT Installation Gide 11/16/11 3:27 PM Page 4