Sie sind auf Seite 1von 16

CODE : 00Z

qSERVICE MANUAL
CONTENTS
Parts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
XEA106USME
ELECTRONIC
CASH REGISTER
MODEL XE-A106

SRV KEY
PRINTER
: Not necessary
: M-31
(U version)
CHAPTER 1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CHAPTER 2. OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CHAPTER 3. MASTER RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CHAPTER 4. HARDWARE DESCRIPTION . . . . . . . . . . . . . . . . . . . . 5
CHAPTER 5. TEST FUNCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CHAPTER 6. SERVICE PRECAUTION . . . . . . . . . . . . . . . . . . . . . . 10
CHAPTER 7. CIRCUIT DIAGRAM AND PWB LAYOUT . . . . . . . . . 11
PARTS GUIDE
XE-A106 LEAD-FREE SOLDER
LEAD-FREE SOLDER
The PWBs of this model employs lead-free solder. The LF marks indicated on the PWBs and the Service Manual mean Lead-Free sol-
der.
The alphabet following the LF mark shows the kind of lead-free solder.
Example:
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a
breakdown or an accident.
Since the melting point of lead-free solder thread is about 40C higher than that of conventional lead solder thread, the use of the exclu-
sive-use soldering iron is recommendable.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220C, which is about 40C higher than that of conventional lead solder, and its solder-
ing capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land
separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB
when completion of soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip
after completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.
CAUTIONS
THERE IS A RISK OF EXPLOSION IF THE BATTERY
IS REPLACED BY AN INCORRECT TYPE.
PROPERLY DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
5mm
Lead-Free
Solder composition
code (Refer to the
table at the right.)
<Solder composition code of lead-free solder>
Solder composition
Sn-Ag-Cu
Sn-Ag-Bi
Sn-Ag-Bi-Cu
Sn-Zn-Bi
Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
Bi-Sn-Ag-P
Bi-Sn-Ag
a
b
z
i
n
s
p
Solder composition code
a
XE-A106 SPECIFICATIONS
1
CHAPTER 1. SPECIFICATIONS
1. APPEARANCE
Front view
2. RATING
3. KEYBOARD
1) KEYBOARD LAYOUT
2) KEY LIST
4. MODE SWITCH
LAYOUT
Rotary SW
5. DISPLAY
1) OPERATOR DISPLAY
(Layout)
Weight Approx 5.0kg
External dimension
(Including the drawer)
330 (W) x 363 (D) x 234 (H) mm
13 (W) x 14.3 (D) x 9.2 (H) inches
Power source 120V ACm 10% 60Hz
Power consumption Stand-by 4W
Operating 12.5W
Working temperature 0~40C (32 to 104F)
Type Normal keyboard
Key position STD/MAX 30
Key pitch 19 (W) x 19 (H) mm
Key layout Fixed type
Display
Drawer
Drawer lock
Printer cover
Mode switch
Keyboard
@/TM
TAX1
SHIFT
/RA
TAX2
SHIFT
/PO
VOID
SHIFT PLU
ESC
%
3
7
2
6
1
5
4
8
CHK CLK#
#/
SBTL
CH
CA/AT/NS
Keytop Description
0-9,00 Numeric keys
CL Clear key
@/TM Multiplication & Time key
2 Paper feed key
Tax 1 Shift/RA Tax 1 shift and Received on account key
Tax2 Shift/PO Tax 2 shift and Paid out key
% Percent keys
ESC Error escape key
VOID Void key
CLK# Clerk code Entry key
PLU PLU code entry key
SHIFT Department shift key
#/SBTL Non-add code & subtotal key
CHK Check key
CH Charge key
CA/AT/NS Cash and Amount tender and No Sales key
Dept1-8 Department key
Display device: LED numeric display
Number of line: 1 line
Number of positions: 8 positions numeric display
Color of display: Yellow Green
Character size: Numeric 14 (H) x 8 (W) mm
REG
X/Flash
Z/PGM
VOID
OFF
PLU code
Repeat
Department code
XE-A106 SPECIFICATIONS
2
2) DISPLAY CONTENTS
Departments/PLU Code:
The department code or PLU code entered appears on the left. For
example, if the key for department 1 is pressed, "1" would ap-pear in
the extreme left position.
Repeat:
Indicates the number of times the same department key is pressed. If
an entry is repeated more than ten times, only the first digit is dis-
played (12 displays as "2").
(E) Error:
This symbol appears, accompanied by a warning beep, when an
error is made. If this occurs during a transaction because of an ex-
cessive digit entry, simply press [CL] and re-enter correctly.
(P) Program:
This symbol remains on the display when the cash register is be-ing
programmed in the Z/PGM mode.
(F) Finalization:
This symbol appears when a transaction is finalized by pressing [CA/
AT/NS], [CH] or [CHK].
(o) Subtotal:
This symbol appears when [#/SBTL] is pressed and the cash register
computes the subtotal, and also when the amount ten-dered is less
than the total sale amount.
(C) Change:
This symbol appears whenever the change due amount is dis-played.
(L) Low battery:
This symbol appears when the power of the installed batteries is
below a certain level or you need to replace the batteries with new
ones. (see the "Maintenance" section for explanation.)
(L) No battery:
This symbol appears when no batteries are installed. (see "Main-ten-
ance" and "Getting Started" sections for explanation.)
In addition, the following appear when appropriate:
The minus sign (-) can appear in positions 2 to 8.
The decimal point appears in positions 1 to 3.
When entry of the secret code is necessary, "---" appears in
posi-tions 1 to 4.
6. PRINTER
1) PRINTER
2) PAPER
3) INKING
4) LOGO STAMP (NONE)
5) CUTTER
Manual cutter
6) PRINTING WHEEL LAYOUT
Model name : M-31
No. of stations : 1
Printing system : Print wheel selective type
Printing capacity : max. 13 characters
Character size : 1.6mm (W) x 2.8mm (H)
Print pitch : Column distance 2.1mm (numeric to
numeric), 2.6mm (numeric to symbol)
Row distance 4.6mm
Print speed : Approximate 1.4 lines/s (6 digits/line)
Paper feed speed : Approximate 4.3 lines/s
Reliability : MCBF 0.3 million lines
Paper roll dimension : 58mm 80
Paper quality : Bond paper (paper thickness: 0.06 to
0.085mm paper weight: 47 to 64g/m
2
)
Ink supply system : Ink roll
From : Roller
Specification : Material - rubber
Ink roll type : 1 million characters
Print color : purple
1
2
3
4
5
6
7
8
9
10
11
12
13
0
1 2 3 4 5 6 7 8 9 10 11 12
#
13
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
#
1
2
3
4
5
6
7
8
9
0
CG
Z
RA
PO
VD
%
@
ST
TX
CA
X
CK
CH
XE-A106 SPECIFICATIONS
3
7. DRAWER
[OUTLINE]
Standard equipment : Yes (1)
Max. number of drawers : 1
The drawer consists of :
(1) Drawer box (outer case) and drawer
(2) Money case
(3) Coin case
(4) Lock (attached to the drawer)
[SPECIFICATION]
1) DRAWER BOX AND DRAWER
2) MONEY CASE
Layout:
3) LOCK (LOCK KEY : LKGIM7331BHZZ)
Location of the lock: Front
Method of locking and unlocking:
To lock, insert the drawer lock key into the lock and turn it 90 degrees
counter clockwise. To unlock, insert the drawer lock key and turn it 90
degrees clockwise.
Key No: 301
8. BATTERY
1) MEMORY BACK UP BATTERY
For memory back up, the dry battery ULM-3 (3 pieces) are needed.
1. Memory holding time:
Approx. 1 year after New dry batteries are installed.
2. Battery exchange method:
When the low battery symbol "L" lights up, replace the batteries (3
AA) replaced by the following method;
1) Power on the ECR.
2) Mode switch turn to "REG" mode.
3) Remove the OLD dry batteries (3 pieces).
4) The nobattery symbol "L" light up.
5) Insert the NEW dry batteries (3 pieces).
6) Confirm the low battery symbol "L" and nobattery symbol "L" is
off.
2) LOW BATTERY
Low battery indication will appear on the left side of display when the
battery voltage is low.
CASE 1: When sitting idle or after completion of transaction.The
machine can indicate the low battery condition (Always)
CASE 2: Low battery indication will not appear during key opera-tions,
but will appear after power up of the cash register.
[Display sample]
" 0.00 " : Battery is OK.
"L 0.00" : Low battery (You have to change the batteries.)
After finalization
"F 12.34": Battery is OK.
"L 12.34": Low battery ("L" indicate instead of "F".)
3) NO BATTERY
If the user forgets to replace the battery and the battery voltage falls
below a certain level, or if a power failure occurs with no batteries
installed, the memory contents cannot be retained. The CPU judges it
as no battery and performs the master reset. In this case, all the set-
tings and registrations are cleared. If, however, the power is con-tinu-
ously supplied to the AC cord, the memory contents are retained.
Low battery : Batteries are installed, but the voltage is low. Memory
back up can be done.
No battery : Batteries are not installed or the voltage is extremely low.
The master reset is executed when a power failure occurs,
when the batteries are not properly changed.
Low battery & No battery indication will appear at the most left position
of display when the battery voltage is low.
CASE 1: When any numeric entry & item entry is not done or just after
finalization.
The machine can indicate the battery condition. (Always)
CASE 2: When numeric entry or item entry is done.
Battery condition is not appeared.
Exceptionally, at the power is restored after power failure, the
low battery & No battery indication will appear on the display
only when the battery voltage is low.
And the indication will disappear after any key entry.
[Display sample]
" 0.00" : Battery is OK.
"L 0.00" : Low battery
"L 0.00" : No battery
After finalization
"F 12.34": Battery is OK.
"L 12.34": Low battery ("L" indicate instead of "F".)
"L 12.34": No battery ("L" indicate instead of "F".)
Size 330 (w) x 363 (d) x 98 (h)
Material Plastic
Bell -
Release lever Standard equipment: situated at the bottom
Drawer open sensor -
Separation from the drawer Disallowed
Separation of the bill compartments from the coin
compartments
Allowed
Bill separator -
Number of compartments 4B/5C
4B/5C
L L
XE-A106 OPTIONS
4
CHAPTER 2. OPTIONS
1. OPTIONS (NONE)
2. SERVICE OPTIONS (NONE)
3. SUPPLIES
4 SPECIAL SERVICE TOOLS (NONE)
CHAPTER 3. MASTER RESET
Master reset:
Clears all the memory and initializes each preset parameter.
The master reset should be performed by using the following procedure.
1. Turn off the power (Power OFF). (See Note 1.)
2. Let the ECR be without the memory back up battery.
3. Turn the mode switch to the others of Power-off position.
4. Turn on the power (Power ON). (See Note 2.)
When the master rest is completed, the buzzer sounds intermittently
three times.
5. Attach the memory back up battery to the ECR.
The master reset can also be accomplished in the following case.
(See Note 3.)
Note 1) Power OFF:
Means disconnecting the AC power supply to the
machine. (Specifically, unplugging the machine.)
Note 2) Power ON:
Means connecting the AC power to the ma-chine. (Specif-
ically, plugging in the machine.)
Note 3) In case a power failure occurs when the machine has no
battery installed, the master reset operation is automati-
cally performed after the power has been restored.
NO NAME PARTS CODE PRICE RANK DESCRIPTION
1 ROLL PAPER DPAPR1025CSZZ AS 5 ROLLS/PACK
2 INK ROLLER NROLR1022CC05 AF
XE-A106 HARDWARE DESCRIPTION
5
CHAPTER 4. HARDWARE DESCRIPTION
1. OUTLINE
2. BLOCK DIAGRAM
3. DISCRIPTION
1) DISPLAY
(Output Timing of STROBE signal)
2) KEYBOARD AND MODE SW
MODE SW, KEY MATRIX is follows.
*Note: Although the XE-A106 has 30 keys, the keyboard circuit is
actually 32 keys (+) the PF key.
3) BUZZER
The BUZZER is driven by the P75/BUZ signal of the CPU.
Frequency : 4.095kHz
CPU : uPD780023A (ROM 24KB, RAM 1024B)
KEY BOARD : 30key including PF key
MODE SW : 5position slide SW
DISPLAY : 7seg.+DP x 8digit LED (YELLOW GREEN) FRONT only
DRAWER : 1ch, no open sensor
BUZZER : 1beep, piezo buzzer
PRINTER : M-31
6V
CPU
uPD780023A
D
Printer
M-31
RAWER
KEY
BOARD
&
MODE SW
8. 8. 8. 8. 8. 8. 8.
FRONT display :8digit
POWER
SUPPLY
AC
5V
ST1- ST4-,ST5
A1 G1,DP1,A2 G2 ~ ,DP2
KST1 KST8
KR1 KR6
8.
BUZZER
MAIN
4.19MHz
For Clock
32.768kHz
Battery
5V
ST4- ST5- (V) ST3- ST2- ST1-







ST1-
ST2-
ST3-
ST4-
1ms
30~100us
Display
strobe
SW1
MODE SW
KST2
KR1
KST3
KST4
KST5
1
2
3
4
5
22
31 7
15 16
24 25
26 1 2
8 9 10
17 18 19
27 28
3 4
11 12
21
30
5 6
13 14
32
6 7 13 25
D13 1SS133 KST1
1 2 8 14
D14 1SS133 KST2
11 12 19 9
D15 1SS133 KST3
17 18 3 23
D16 1SS133 KST4
28 24 20 10
D17 1SS133 KST5
30 26 21 4
D18 1SS133 KST6
32 22 15 5
D19 1SS133 KST7
29 31 27 16
D20 1SS133 KST8
KST1
1
2
3
4
5
6
7
8
9
KCN2
KR2 KR6 KR5 KR4 KR3
KEYBOARD
1
2
3
4
5
Rotary SW
REG
OFF
VOID
X/Flash
/PGM Z
XE-A106 HARDWARE DESCRIPTION
6
4) REWIND MOTOR
When the rewind motor is driven by the signal of the CPU.
5) DRAWER
DRAWER OPEN signal :Output high signal between 50ms
6) DETECTING "LOW VOLTAGE"
Values obtained by AD conversion and averaging
Register value: 138 (L 2.7V) or less 3 No voltage
139 - 154 (L 2.7V - 3.0V) 3 Low voltage
more than 154 3 OK
7) DESTINATION DETECTION PORT
P66 L
5ms 10ms 15ms
PRINTER
MOTOR
REWIND
MOTOR
XE-A106 HARDWARE DESCRIPTION
7
4. CPU PORT TABLE
No. PIN Name Signal Name Description Output/Input Initial state When STBY
1 P50/A8 RWND REWIND MOTOR O L O/L
2 P51/A9 DR To DRAWER O L O/L
3 P52/A10 SA2 DISPLAY SEGMENT O L O/L
4 P53/A11 SB2 DISPLAY SEGMENT O L O/L
5 P54/A12 SC2 DISPLAY SEGMENT O L O/L
6 P55/A13 SD2 DISPLAY SEGMENT O L O/L
7 P56/A14 SE2 DISPLAY SEGMENT O L O/L
8 P57/A15 SF2 DISPLAY SEGMENT O L O/L
9 Vss0 GND
10 Vdd0 VDD
11 P30 ST1- DISPLAY STROBE N-Ch O.D. O H I
12 P31 ST2- DISPLAY STROBE N-Ch O.D. O H I
13 P32 ST3- DISPLAY STROBE N-Ch O.D. O H I
14 P33 ST4- DISPLAY STROBE N-Ch O.D. O H I
15 P34/SI31 ST5 DISPLAY STROBE (H ACTIVE) O L O/L
16 P35/SO31 NU (GND via 56k) I I
17 P36/SCK31- NU (GND via 56k) I I
18 P20/SI30 SA1 DISPLAY SEGMENT O L O/L
19 P21/SO30 SB1 DISPLAY SEGMENT O L O/L
20 P22/SCK30- SC1 DISPLAY SEGMENT O L O/L
21 P23/RXD0 SD1 DISPLAY SEGMENT O L O/L
22 P24/TXD0 SE1 DISPLAY SEGMENT O L O/L
23 P25/ASCK0 SF1 DISPLAY SEGMENT O L O/L
24 Vdd1 VDD
25 Avss GND
26 P17/ANI7 VBAT BATTERY voltage I I
27 P16/ANI6 NU RESERVE FOR KEY RETURN I I
28 P15/ANI5 KR6 KEY RETURN I I
29 P14/ANI4 KR5 KEY RETURN I I
30 P13/ANI3 KR4 KEY RETURN I I
31 P12/ANI2 KR3 KEY RETURN I I
32 P11/ANI1 KR2 KEY RETURN I I
33 P10/ANI0 KR1 KEY RETURN I I
34 Avref VCC
35 Avdd VDD
36 RESET- RESET-
37 XT2 XT2 32.768Khz Xtal
38 XT1 XT1 32.768Khz Xtal
39 IC/VPP GND
40 X2 X2 SYSTEM CLOCK
41 X1 X1 SYSTEM CLOCK
42 Vss1 GND
43 P00/INTP0 /POF POWER OFF I I
44 P01/INTP1 T From PRINTER I I
45 P02/INTP2 t From PRINTER I I
46 P03/INTP3/ADTRG R From PRINTER I I
47 P70/TI00/TO0 SG1 DISPLAY SEGMENT O L O/L
48 P71/TI01 SDP1 DISPLAY SEGMENT O L O/L
49 P72/TI50/TO50 SG2 DISPLAY SEGMENT O L O/L
50 P73/TI51/TO51 SDP2 DISPLAY SEGMENT O L O/L
51 P74/PCL NU O L O/L
52 P75/BUZ BUZ BUZZER O L O/L
53 P64/RD- MTR To PRINTER O L O/L
54 P65/WR- TRG To PRINTER O L O/L
55 P66/WAIT- MSL1 MODEL SELECT1 I I
56 P67/ASTB MSL2 MODEL SELECT2 I I
57 P40/AD0 KST1 KEY STROBE O L O/L
58 P41/AD1 KST2 KEY STROBE O L O/L
59 P42/AD2 KST3 KEY STROBE O L O/L
60 P43/AD3 KST4 KEY STROBE O L O/L
61 P44/AD4 KST5 KEY STROBE O L O/L
62 P45/AD5 KST6 KEY STROBE O L O/L
63 P46/AD6 KST7 KEY STROBE O L O/L
64 P47/AD7 KST8 KEY STROBE O L O/L
XE-A106 TEST FUNCTION
8
CHAPTER 5. TEST FUNCTION
1) To execute the diag test, set the mode switch to Z/PGM. Enter the
desired JOB code, and press the PO (paid out) key.
2) The test message is printed by the printer.
3) Test contents and key operations.
1. MODE SWITCH TEST
1) KEY OPERATION
2) TEST PROCEDURE
Change over the mode switch as follows. If the mode switch data in the
proper sequence is not read with the above operation, an error is
printed.
To cancel this test mode, set the mode switch to any a position other
than Z/PGM to Z/PGM. In this case, the completion print is performed.
During the test , the display indicates hard codes which correspond to
the switch positions.
3) MODE SWITCH OPERATION
Completion print 01
Error print - - - 01
2. KEY TEST
1) KEY OPERATION
2) TEST PROCEDURE
Perform the keyboard check with the sum check data of the key code.
Enter the sum check data of each model in the four digits preceding the
diag number 02, and compare the data with the key position code which
is added until the CA/AT/NS key is pressed.
If the data coincides with the code, the completion print is performed.
If not, the error print is performed.
3. DISPLAY BUZZER TEST
1) KEY OPERATION
2) TEST PROCEDURE
Check the continuous buzzer sound and the display state.
Display state:
8. 7. 6. 5. 4. 3. 2. 1.
The decimal point will shift from the lower digit to the upper, step by step
(500mSEC). To cancel the test mode, press any key, and the buzzer will
stop and the completion print is performed.
Completion print 03
4. DRAWER TEST
1) KEY OPERATION
2) TEST PROCEDURE
The drawer opens with the above key operation. Check that the drawer
is open. Press any key to terminate the test.
Completion print 04
NO. Test contents Key operations
1 Mode switch test 1 3 [PO]
2 Key test 2 3 [PO]
3 Display buzzer test 3 3 [PO]
4 Drawer test 4 3 [PO]
5 Printer test 5 3 [PO]
6 CPU version NO. print 6 3 [PO]
7 Battery level test 7 3 [PO]
8 Time display test 8 3 [PO]
9 Destination display 9 3 [PO]
PO 1
Mode:
Display: (01) (02)
X/FLASH
(03)
Z/PGM
(04)
OFF REG VOID
Completion print 02
Error print - - -02
XXXX Sum data
PO 2
PO 3
PO 4
XE-A106 TEST FUNCTION
9
5. PRINTER TEST
1) KEY OPERATION
2) TEST PROCEDURE
With the above key operation , the print test pattern is repeatedly
printed.
Pressing any key will terminate the test after the completion of one
cycle print. (The receipt is issued at the end.)
6. CPU VERSION NO. PRINT
1) KEY OPERATION
2) DESCRIPTION
The CPU version No. are printed with above key operation.
(Print example)
0102 CPU version NO.
06
This test is terminated when printing is completed.
7. BATTERY VOLTAGE SENSOR TEST
1) KEY OPERATION
2) TEST PROCEDURE
Displays A/D conversion port read value.
0155 or greater : Normal
0154 or smaller : Low battery display
0138 or smaller : No battery display and MSR is done when power on.
To terminate the test, press any key.
Completion print 07
8. TIME DISPLAY TEST
1) KEY OPERATION
2) TEST PROCEDURE
To terminate the test and print the date and time, press any key.
9. DESTINATION DISPLAY
1) KEY OPERATION
2)TEST PROCEDURE
Display the destination code as follows.
Display X (X:0)
To terminate the test, press any key.
Completion print 09
PO 5
PO 6
PO 7
Display 0
PO 8
8
Display
Hour Minute Second
Turn on and off(0.5s)
7 5 4 2 1 3 6
Print
Year Month Date Hour Minute Second
0 8
X X X X X X X X X X X X
PO 9
XE-A106 SERVICE PRECAUTION
10
CHAPTER 6. SERVICE PRECAUTION
1. PRINTER
Since there are no service parts for this model printer, only the printer
unit is supplied. Therefore, the printer component parts are not supplied
and no service document is issued.
For troubleshooting of the printer, refer to the table below:
*Printer life: 300 thousand lines (XE-A106: M-31)
Ink roll life: 1 million characters
Phenomena Check point/possible cause Repair
The printer motor is locked and the buzzer
sounds intermittently.
The printer does not work properly
Check if the printer cable is disconnected. Check and repair the printer cable.
Check if the printer life is reached. Replace the printer.
Check if any foreign material is attached to
the printing type wheel or the gear section.
Remove the foreign material. (After removing
the foreign material, set the mode switch to
"REG" and press "CL" key.)
Defective print (Lack on the upper/ lower or
left/right side)
Check if the printing type is worn down. Replace the printer.
Check if any foreign material is attached to
the printing type wheel.
Remove the foreign material. (After removing
the foreign material, set the mode switch to
"REG" and press "CL" key.)
Thin print Check if the ink roll life is reached. Replace the ink roll.
Check if the ink roll is properly installed. Install the ink roll properly.
Check if the printing type wheel is worn down. Replace the printer.
Uneven pitch of print paper feed Check if the roll paper size is proper. Use roll paper as specified below;
Paper width : 57.5 0.5mm
Outside diameter : 80mm or less
Inside diameter of paper tube: 12mm or less
Paper thickness : 0.06~0.085mm
Check if a load is applied to the roll paper dur-
ing paper feeding. This may result from a for-
eign materials attached to the roll paper.
Remove any foreign material.
XE-A106 CIRCUIT DIAGRAM AND PWB LAYOUT
11
C DBA
C DBA
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1

M
A
I
N

C
I
R
C
U
I
T
O
X
A
3
X
E
A
1
0
2
U
OX
R
2
4
X
A
3
X
E
A
1
0
2
V
7
A
3
X
E
A
1
0
2
V
4
X X
*C
A
U
T
IO
N
*
OO
R
2
2
R
2
1
A
3
X
E
A
1
0
2
A
R
2
3
O
R
E
G
(2
)
X
/F
L
A
S
H
(3
)
V
O
ID
(1
)
Z
/P
G
M
(4
)
V
C
T
W
O
N
L
Y
IC
4
IC
5
9
P
IN
: G
N
D
1
0
P
IN
:
N
. C
B
A
T
T
E
R
Y
C
N
M
Y
L
A
R
M
Y
L
A
R
(F
O
R
:P
R
IN
T
E
R
)
T
1
.0
A
2
5
0
V
J
U
M
P
E
R
M
Y
L
A
R
M
U
L
T
I
M
U
L
T
I
R
O
T
A
R
Y
S
W
IT
C
H
P
C
B
F
L
A
T
C
A
B
L
E
P
R
IN
T
E
R
P
C
B
(F
3
:J
U
M
P
E
R
)
M
O
T
O
R
C
N
(F
O
R
:D
R
A
W
E
R
)
M
U
L
T
I
L
E
A
D
W
IR
E
K
E
Y

S
H
E
E
T
H
O
L
E
O
N
L
Y
A
3
X
E
A
1
0
2
V
6
X
: N
O
T
M
O
U
N
T
O
: 4
7
K
o
h
m
2
4
1
8
1
3
2
7
6
2
3
2
2
3
1
1
6
1
7
1
4
1
0
2
1
2
0
5
1
2
3
2
4
2
5
1
5
2
9
1
9
2
8
19
3
1
1
3
0
7
2
8
2
6
T
R
O
U
T
P
U
T
C
N
UAV
4
V
6
V
7
A
1
E
R
A
1
3
2
A
1
X
E
A
1
2
7
X X
O
O
JJ
OOOOOO
XXXXXX
1
2
3
4
5
T
O
P
V
IE
W
J
U
M
P
E
R
K S T 1
K R 5
S
T
5
/S
T
2
S
F
1
S
D
1
S
B
1
/ST4
ST5
K
S
T
4
/P
O
F
S
F
2
F
E
E
D
K S T 5S C 1
/S
T
3
S
E
2
S
E
1
K
V
5
K
H
4
S G 1
S
B
2
K
V
3
K
S
T
5
K
S
T
3
M T R
T
K V 3
K S T 7
K
V
7
K
V
6
K
S
T
2
K
S
T
[1
:8
]
K
H
[1
:4
]
M
T
R
K R 1
/ST1
K
V
8
K
S
T
7
K
H
2
S G 2
K
S
T
5
R
K S T 2
K S T 6
S F 1
D
R
S
C
1
K
S
T
4
D P 2
K S T 8
t
S D 1
S B 1
S A 1
/S
T
1
S
D
2
D
P
1
/ P O F
S
G
2
K V 2
K
S
T
8
K
H
4
K V 8
/R
E
S
E
T
K R 3
S
F
2
S
C
2
/S
T
[1
:5
]
T
R
G
K
H
1
K V 7
K R 4
R
W
N
D
K
V
4
R W N D
K S T 4
K R 2
K
S
T
6
S
[1
:1
6
]
K V 4
t
D P 1
S
G
1
K
H
3
K
H
1
S
D
2
K
V
2
K
H
3
K V 6
K V 5
S E 1
/S
T
4
S
A
1
S
B
2
S
A
2
K S T 3
R
K R 6
D
P
2
K
V
1
T R G
K
S
T
1
K V 1
F
E
E
D
/ST2
K
H
2
K
S
T
3
K
S
T
2
T
/ST3
S
E
2
S
C
2
S
A
2
S
W
2
7
2
5
C
O
N
3
A
H
O
L
E
O
N
L
Y
+
C
2
6
4
7
u
F
/1
6
V
D
2
0
1
N
4
1
4
8
C
N
2
2
5
2
1
P
0
2
0
0
T
12
Q
6
K
T
A
1
2
7
1
Y
A
T
/
P
S
W
2
8
1
4
C
N
4
2
5
2
1
P
0
2
0
0
T
12
12345678
S
W
2
9
9
L
E
D
5
S
5
6
8
G
W
A
1
2
84
5
1 0
9
3
7
6
R
8
1
k
B
Z
B
U
Z
Z
E
R
P
O
W
E
R
C
O
R
D
IC
2
u
P
D
7
8
0
0
2
3
A
(
Q
F
P
6
4
)
123456789
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1 7
1 8
1 9
2 0
2 1
2 2
2 3
2 4
2 5
2 6
2 7
2 8
2 9
3 0
3 1
3 2
4
8
4
7
4
6
4
5
4
4
4
3
4
2
4
1
4
0
3
9
3
8
3
7
3
6
3
5
3
4
3
3
6 4
6 3
6 2
6 1
6 0
5 9
5 8
5 7
5 6
5 5
5 4
5 3
5 2
5 1
5 0
4 9
P
5
0
/A
8
P
5
1
/A
9
P
5
2
/A
1
0
P
5
3
/A
1
1
P
5
4
/A
1
2
P
5
5
/A
1
3
P
5
6
/A
1
4
P
5
7
/A
1
5
V
S
S
0
V
D
D
0
P
3
0
P
3
1
P
3
2
P
3
3
P
3
4
/S
I3
1
P
3
5
/S
O
3
1
P 3 6 / - S C K 3 1
P 2 0 / S I 3 0
P 2 1 / S O 3 0
P 2 2 / - S C L 3 0
P 2 3 / R X D 0
P 2 4 / T X D 0
P 2 5 / A S C K 0
V D D 1
A V S S
P 1 7 / A N 1 7
P 1 6 / A N 1 6
P 1 5 / A N 1 5
P 1 4 / A N 1 4
P 1 3 / A N 1 3
P 1 2 / A N 1 2
P 1 1 / A N 1 1
P
7
1
/T
I0
1
T
O
0
P
0
3
/IN
T
P
3
/A
D
T
R
G
P
0
2
/IN
T
P
2
IN
P
T
1
IN
P
T
0
V
S
S
1
X
1
X
2
IC
X
T
1
X
T
2
/R
E
S
E
T
A
V
D
D
A
V
R
E
F
P
1
0
/A
N
1
0
P 4 7 / A D 7
P 4 6 / A D 6
P 4 5 / A D 5
P 4 4 / A D 4
P 4 3 / A N 3
P 4 2 / A D 2
P 4 1 / A D 1
P 4 0 / A D 0
P 6 7 / A S T B
P 6 6 / - W A I T
P 6 5 / - W R
P 6 4 / - R D
P 7 5 / B U Z
P 7 4 / P C L
P 7 3 / T I 5 1 / T O 5 1
P 7 2 / T I 5 0 / T O 5 0
R
6
3
F
3T
1
.0
A
L
/2
5
0
V
C
1
2
1
8
P
S
W
3
0
2
3
R
5
6
3
3
0
R
E
G
(5
)
X
/F
L
A
S
H
(4
)
V
O
ID
(1
)
Z
/P
G
M
(3
)
O
F
F
(2
)
P
O
W
E
R
R
O
T
A
R
Y

S
W
(
X
E
-
A
1
0
2
)
tT
R
A
N
S
F
O
R
M
E
R
1
3
2
4
X
2
4
.1
9
M
H
z
1
2
3
P
/H
C
O
N
5
2
0
1
1
-0
8
1
0
12345678
S
W
3
1
1
0
C
1
3
2
2
P
F
1
T
1
.2
5
A
L
/1
2
5
V
R
1
2
5
6
K
S
W
3
2
4
R
1
3
5
6
K
D
3
1
N
4
0
0
2

4
M
T
im
in
g
s
u
b
-s
ig
n
a
l
c
o
m
m
o
n
R
e
s
e
t s
ig
n
a
l
T
im
in
g
s
ig
n
a
l
M
o
to
r
(-)
M
o
to
r(+
)
T
rig
g
e
r(+
)
T
rig
g
e
r(-)
M
-
3
1

O
R

M
-
4
2
V
P
R
IN
T
H
E
A
D
E
R
12345678
S
W
3
3
5
R
1
4
5
6
K
D
4
Q
7
K
T
A
1
2
7
1
Y
A
T
/P
R
2
1
4
7
K
S
W
3
4
1
6
R
4
9
1
1
0
R
1
5
4
7
K
D
2
R
5
8
3
3
0
R
2
2
4
7
K
R
1
6
4
7
K
D
1
D
2
3
R
2
3
4
7
K
R
1
7
4
7
K
R
4
2
1
1
0
R
2
4
4
7
K
R
1
8
4
7
K
R
5
1
1
2
K
R
2
5
4
7
0
R
1
9
4
7
K
C
2
7
0
.1
u
F
R
2
0
4
7
K
S
P
1
S
H
O
R
T
P
IN
Q
9
K
T
A
1
2
7
1
Y
A
T
/
P
IC
5
K
ID
6
5
0
8
3
A
P
(D
IP
)
123456789
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
123456789
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
Q
4
2
S
C
1
8
1
5
G
R
R
2
1
M
+
C
2
3
3
0
0
u
F
/2
5
V
X
1
3
2
.7
6
8
K
H
z
R
3
6
8
K
D
1
3
1
N
4
1
4
8
+
C
3
3
3
0
u
F
/2
5
V
R
2
9
1
K R
4
5
.6
K
+
C
4
1
0
0
u
F
/2
5
V
R
5
5
6
K
R
3
0
1
K
D
5
1
N
4
0
0
2
R
6
1
0
0
K
R
2
8
1
K
a
a
b
c
d
e
e
f
g
g
d
p
d
p
L
E
D
1
D
5
6
8
G
W
A
1
2
3
4
5
6
7
8
9
1 8
1 7
1 6
1 5 1 4
1 31 2
1 1
1 0
D
6
1
N
4
0
0
2
R
3
1
1
0
K
R
7
1
K
R
4
4
1
1
0
D
7
1
N
4
1
4
8
R
3
2
1
0
K
D
8
1
N
4
1
4
8
C
5
0
.1
u
F
R
3
3
1
0
K
D
9
1
N
4
1
4
8
Q
2
2
S
D
2
1
7
0
S
O
T
-
8
9
Q
5
K
T
A
1
2
7
1
Y
A
T
/ P
C
1
5
0
.1
u
F
Q
3
2
S
C
1
8
1
5
G
R
D
1
0
1
N
4
1
4
8
R
3
9
1
1
0
C
1
6
0
.1
u
F
R
7
0
1
0
0
D
1
1
1
N
4
0
0
2
C
1
4
0
.1
u
F
C
1
0
.0
3
3
u
F
L
E
D
4
D
5
6
8
G
W
A
1
2
3
4
5
6
7
8
9
1 8
1 7
1 6
1 5 1 4
1 31 2
1 1
1 0
R
4
6
1
1
0
R
4
8
1
1
0
R
3
7
1
1
0
D
2
2
1
N
4
1
4
8
12345H
B
0
5
0
1
0
1
0
S
W
_
C
O
N
S
W
3
6
Q
8
K
T
A
1
2
7
1
Y
A
T
/P
R
5
9
6
.8
K
R
6
2
4
7
K
S
W
4
1
S
W
5
1
1
+
C
8
1
0
u
F
D
3
0
1
N
4
0
0
2
R
2
6
3
3
0
K
S
W
6
1
7
IC
3
L
B
1
2
6
8
(D
IP
)
8765
1234
N
C
2
O
1
O
2
V
C
C
N
C
1
I1I2G
N
D
S
W
7
2
8
S
W
8
3
0
C
N
1
3
0
6
1
P
0
2
0
2
T
12
12
R
1
2
2
0
S
W
9
3
2
12345
1
2
5
3
-5
P
K
C
N
2
R
3
5
1
1
0
R
5
7
6
.8
K
+
C
9
2
2
u
F
/5
0
V
S
W
1
0
2
9
R
4
0
1
1
0
C
1
0
0
.1
u
F
IC
1
L
M
7
8
0
6 T
O
-
2
2
0
1
2
3
V
IN
G N D
V
O
U
T
S
W
1
1
7
R
3
6
1
1
0
L
E
D
2
D
5
6
8
G
W
A
1
2
3
4
5
6
7
8
9
1 8
1 7
1 6
1 5 1 4
1 31 2
1 1
1 0
S
W
1
2
2
R
4
1
1
1
0
C
1
1
0
.1
u
F
D
1
2
1
N
4
1
4
8
R
6
0
3
3
0
S
W
1
3
1
2
R
3
4
1
1
0
R
4
7
1
1
0
R
5
3
6
.8
K
R
9
4
.7
K
S
W
1
4
1
8
R
5
4
3
3
0
S
W
1
5
2
4
R
2
7
1
M
C
1
7
1
0
0
P
R
1
0
2
.7
K
IC
4
K
ID
6
5
0
8
3
A
P
(D
IP
)
123456789
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
123456789
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
R
1
1
1
K
S
W
1
6
2
6
C
1
8
1
0
0
P
S
W
1
M
O
D
E
S
W
12345
C
O
N
3
H
O
L
E
O
N
L
Y
S
W
1
7
2
2
C
1
9
1
0
0
P
123456789
K
C
N
1
1
2
5
3
-9
P
R
4
5
1
1
0
C
N
3
2
5
4
1
P
0
3
0
0
T
123
S
W
1
8
3
1
C
2
0
1
0
0
P
Z
D
1
H
Z
7
B
3
-T
A
-E
S
W
1
9
1
3
C
2
1
1
0
0
P
R
5
5
6
.8
K
R
3
8
1
1
0
S
W
2
0
8
C
2
2
3
3
0
0
P
12
R
6
1
6
.8
K
D
2
1
1
N
4
0
0
2
S
W
2
1
1
9
C
2
3
3
3
0
0
P
R
4
3
1
1
0
L
E
D
3
D
5
6
8
G
W
A
1
2
3
4
5
6
7
8
9
1 8
1 7
1 6
1 5 1 4
1 31 2
1 1
1 0
D
1
4
1
N
4
1
4
8
R
5
2
3
3
0
C
2
4
3
3
0
0
P
S
W
2
2
3
D
1
5
1
N
4
1
4
8
S
W
2
3
2
0
C
2
5
3
3
0
0
P
C
7
0
.1
u
F
D
1
6
1
N
4
1
4
8
S
W
2
4
2
1
C
2
9
3
3
0
0
P
D
1
7
1
N
4
1
4
8
- +
M
G
1
M
O
T
O
R
F
-7
5
4
R
5
0
4
.7
K
S
W
2
5
1
5
D
1
8
1
N
4
1
4
8
F
2
T
4
0
0
m
A
/2
5
0
V
+
C
3
0
S
W
2
6
2
7
Q
1
2
S
D
2
1
7
0
S
O
T
-
8
9
D
1
9
1
N
4
1
4
8
+
C
6
4
7
u
F
/1
6
V
V
B
A
T
V
D
D
V
D
D
V
C
C
+
6
V
V
O
+
6
V
+
6
V
V
C
C
V
C
C
V
O
V
C
C
V
O
V
C
C
V
O
V
B
A
T
c
b
d
f
a
a
b
c
d
e
e
f
g
g
d
p
d
p
c
b
d
f
a
a
b
c
d
e
e
f
g
g
d
p
d
p
c
b
d
f
a
a
b
c
d
e
e
f
g
g
d
p
d
p
c
b
d
f
a
d
e
f
g
d
p
c
b
J
6
7
m
m
1
/
1
O
X

C
H
A
P
T
E
R

7
.

C
I
R
C
U
I
T

D
I
A
G
R
A
M

A
N
D

P
W
B

L
A
Y
O
U
T
1
.

C
I
R
C
U
I
T
XE-A106 CIRCUIT DIAGRAM AND PWB LAYOUT
12
2. PWB LAYOUT
A side
B side
XE-A106 CIRCUIT DIAGRAM AND PWB LAYOUT
13
3. DISPLAY LAYOUT
A side
B side

SHARP CORPORATION
Business Solutions Group
CS Promotion Center
Yamatokoriyama, Nara 639-1186, Japan
2009 October Printed in J apan
Trademark acknowledgements
COPYRIGHT 2009 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.
Microsoft

Windows

operating system is a trademark or copyright of Microsoft


Corporation in the U. S. A. and other countries.
Windows

95, Windows

98, Windows

Me, Windows NT

4.0, Windows

2000,
Windows

XP, Windows

Vista, Windows

2000 Server, Windows

Server 2003
and Internet Explorer

are trademarks or copyrights of Microsoft Corporation in the


U.S.A. and other countries.
IBM and PC/AT are trademarks of International Business Machines Corporation.
Acrobat

Reader Copyright

1987-2002 Adobe Systems Incorporated. All rights


reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks
of Adobe Systems Incorporated.
All other trademarks and copyrights are the property of their respective owners.

Das könnte Ihnen auch gefallen