Sie sind auf Seite 1von 327

Technical Manual Performance Measurement Entities

HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents



Huawei Technologies Proprietary
i
Table of Contents
Chapter 8 Total Traffic of the Office ............................................................................................ 8-1
8.1 Overview of Measurement Set .......................................................................................... 8-1
8.2 MS-Originated Outgoing Traffic......................................................................................... 8-2
8.2.1 Overview of MS_OFFICE_2G_ORGOUT_TRAF ................................................... 8-2
8.2.2 Count of Call Attempts ............................................................................................ 8-2
8.2.3 Count of Wrongly Dialed Numbers.......................................................................... 8-3
8.2.4 Count of Releases Before Ringing.......................................................................... 8-5
8.2.5 Count of Terminal Application Failures ................................................................... 8-6
8.2.6 Count of Common Resource Application Failures.................................................. 8-7
8.2.7 Count of Last-Choice Route Overflow .................................................................... 8-8
8.2.8 Count of Peer Office Congestions........................................................................... 8-9
8.2.9 Count of Callee Busy ............................................................................................ 8-10
8.2.10 Count of Connected Calls ................................................................................... 8-11
8.2.11 Count of Releases Before the Pickup................................................................. 8-12
8.2.12 Count of Long Time No Reply............................................................................. 8-13
8.2.13 Count of Answered Calls..................................................................................... 8-14
8.2.14 Seizure Traffic ..................................................................................................... 8-15
8.2.15 Connected Traffic................................................................................................ 8-16
8.2.16 Answered Traffic ................................................................................................. 8-17
8.2.17 Call Completion Rate .......................................................................................... 8-18
8.2.18 Answer Rate........................................................................................................ 8-18
8.3 MS-Originated Traffic....................................................................................................... 8-19
8.3.1 Overview of MS_OFFICE_2G_ORG_TRAF......................................................... 8-19
8.3.2 Count of Call Attempts .......................................................................................... 8-19
8.3.3 Count of Mobile Caller Authentication Failures..................................................... 8-20
8.3.4 Count of Mobile Caller Ciphering Mode Setting Failures...................................... 8-20
8.3.5 Count of Mobile Caller Barring.............................................................................. 8-21
8.3.6 Count of Mobile Caller Trunk Resource Overflow................................................. 8-21
8.3.7 Count of Mobile Caller Traffic Channel allocations Failures ................................. 8-22
8.3.8 Count of Wrongly Dialed Numbers........................................................................ 8-23
8.3.9 Count of Releases Before Ringing........................................................................ 8-24
8.3.10 Count of Terminal Application Failures............................................................... 8-24
8.3.11 Count of Common Resource Application Failures.............................................. 8-25
8.3.12 Count of Connected Calls ................................................................................... 8-26
8.3.13 Count of Answered Calls..................................................................................... 8-27
8.3.14 Seizure Traffic ..................................................................................................... 8-28
8.3.15 Connected Traffic................................................................................................ 8-28
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
ii
8.3.16 Answered Traffic ................................................................................................. 8-29
8.3.17 Call Completion Rate .......................................................................................... 8-29
8.3.18 Answer Rate........................................................................................................ 8-30
8.3.19 Count of Callee Power-Off .................................................................................. 8-30
8.4 MS-Terminated Incoming Traffic ..................................................................................... 8-30
8.4.1 Overview of MS_OFFICE_2G_INCTRM_TRAF ................................................... 8-30
8.4.2 Count of Call Attempts .......................................................................................... 8-31
8.4.3 Count of Releases Before Ringing........................................................................ 8-32
8.4.4 Count of Terminal Application Failures ................................................................. 8-33
8.4.5 Count of Common Resource Application Failures................................................ 8-34
8.4.6 Count of Callee Busy ............................................................................................ 8-35
8.4.7 Count of Mobile Callee Trunk Resource Overflow................................................ 8-36
8.4.8 Count of Mobile Callee Traffic Channel allocations Failures ................................ 8-37
8.4.9 Count of MS Unavailable ...................................................................................... 8-38
8.4.10 Count of Connected Calls ................................................................................... 8-39
8.4.11 Count of Releases Before the Pickup................................................................. 8-40
8.4.12 Count of Long Time No Reply............................................................................. 8-41
8.4.13 Count of Mobile Callee Determined Busy........................................................... 8-43
8.4.14 Count of Answered Calls..................................................................................... 8-43
8.4.15 Seizure Traffic ..................................................................................................... 8-44
8.4.16 Connected Traffic................................................................................................ 8-45
8.4.17 Answered Traffic ................................................................................................. 8-46
8.4.18 Call Completion Rate .......................................................................................... 8-47
8.4.19 Answer Rate........................................................................................................ 8-47
8.5 MS-Terminated Traffic ..................................................................................................... 8-48
8.5.1 Overview of MS_OFFICE_2G_TRM_TRAF ......................................................... 8-48
8.5.2 Count of Call Attempts .......................................................................................... 8-48
8.5.3 Count of Terminal Application Failures ................................................................. 8-49
8.5.4 Count of Common Resource Application Failures................................................ 8-50
8.5.5 Count of Callee Busy ............................................................................................ 8-51
8.5.6 Count of Mobile Callee Trunk Resource Overflow................................................ 8-52
8.5.7 Count of Mobile Callee Traffic Channel allocations Failures ................................ 8-53
8.5.8 Count of MS Unavailable ...................................................................................... 8-54
8.5.9 Count of Connected Calls ..................................................................................... 8-55
8.5.10 Count of Releases Before the Pickup................................................................. 8-56
8.5.11 Count of Long Time No Reply............................................................................. 8-57
8.5.12 Count of Mobile Callee Determined Busy........................................................... 8-58
8.5.13 Count of Answered Calls..................................................................................... 8-59
8.5.14 Seizure Traffic ..................................................................................................... 8-60
8.5.15 Connected Traffic................................................................................................ 8-61
8.5.16 Answered Traffic ................................................................................................. 8-62
8.5.17 Call Completion Rate .......................................................................................... 8-63
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
iii
8.5.18 Answer Rate........................................................................................................ 8-63
8.6 3G VP Subscriber Originated Traffic ............................................................................... 8-64
8.6.1 Overview of MS_VP_3G_ORG_TRAF ................................................................. 8-64
8.6.2 Count of VP Call Attempts .................................................................................... 8-64
8.6.3 Count of VP Connected Calls ............................................................................... 8-65
8.6.4 Count of VP Answered Calls................................................................................. 8-66
8.6.5 Count of Failures Due to Bearer Capability .......................................................... 8-67
8.6.6 Seizure Traffic ....................................................................................................... 8-68
8.6.7 VP Connected Traffic............................................................................................ 8-68
8.6.8 VP Answered Traffic ............................................................................................. 8-68
8.6.9 VP Call Completion Rate ...................................................................................... 8-69
8.6.10 VP Answer Rate.................................................................................................. 8-69
8.7 3G VP Subscriber Terminated Traffic.............................................................................. 8-69
8.7.1 Overview of MS_VP_3G_TRM_TRAF.................................................................. 8-69
8.7.2 Count of VP Call Attempts .................................................................................... 8-70
8.7.3 Count of VP Connected Calls ............................................................................... 8-71
8.7.4 Count of VP Answered Calls................................................................................. 8-72
8.7.5 Count of Failures Due to Bearer Capability .......................................................... 8-73
8.7.6 Seizure Traffic ....................................................................................................... 8-74
8.7.7 VP Connected Traffic............................................................................................ 8-74
8.7.8 VP Answered Traffic ............................................................................................. 8-74
8.7.9 VP Call Completion Rate ...................................................................................... 8-75
8.7.10 VP Answer Rate.................................................................................................. 8-75
8.8 UE-Originated Outgoing Traffic ....................................................................................... 8-75
8.8.1 Overview of MS_OFFICE_3G_ORGOUT_TRAF ................................................. 8-75
8.8.2 Count of Call Attempts .......................................................................................... 8-76
8.8.3 Count of Wrongly Dialed Numbers........................................................................ 8-77
8.8.4 Count of Releases Before Ringing........................................................................ 8-79
8.8.5 Count of Terminal Application Failures ................................................................. 8-80
8.8.6 Count of Common Resource Application Failures................................................ 8-81
8.8.7 Count of Outgoing Trunk Overflow........................................................................ 8-82
8.8.8 Count of Peer Office Congestions......................................................................... 8-83
8.8.9 Count of Callee Busy ............................................................................................ 8-84
8.8.10 Count of Connected Calls ................................................................................... 8-85
8.8.11 Count of Releases Before the Pickup................................................................. 8-86
8.8.12 Count of Long Time No Reply............................................................................. 8-87
8.8.13 Count of Answered Calls..................................................................................... 8-88
8.8.14 Seizure Traffic ..................................................................................................... 8-89
8.8.15 Connected Traffic................................................................................................ 8-90
8.8.16 Answered Traffic ................................................................................................. 8-91
8.8.17 Call Completion Rate .......................................................................................... 8-92
8.8.18 Answer Rate........................................................................................................ 8-92
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
iv
8.9 UE-Originated Traffic ....................................................................................................... 8-93
8.9.1 Overview of MS_OFFICE_3G_ORG_TRAF......................................................... 8-93
8.9.2 Count of Call Attempts .......................................................................................... 8-93
8.9.3 Count of Mobile Caller Authentication Failures..................................................... 8-94
8.9.4 Count of Mobile Caller Ciphering Mode Setting Failures...................................... 8-94
8.9.5 Count of Mobile Caller Barring.............................................................................. 8-95
8.9.6 Count of Mobile Caller Trunk Resource Overflow................................................. 8-95
8.9.7 Count of Mobile Caller Traffic Channel allocations Failures ................................. 8-96
8.9.8 Count of Wrongly Dialed Numbers........................................................................ 8-97
8.9.9 Count of Releases Before Ringing........................................................................ 8-98
8.9.10 Count of Terminal Application Failures............................................................... 8-98
8.9.11 Count of Common Resource Application Failures.............................................. 8-99
8.9.12 Count of Connected Calls ................................................................................... 8-99
8.9.13 Count of Answered Calls................................................................................... 8-100
8.9.14 Seizure Traffic ................................................................................................... 8-101
8.9.15 Connected Traffic.............................................................................................. 8-101
8.9.16 Answered Traffic ............................................................................................... 8-102
8.9.17 Call Completion Rate ........................................................................................ 8-102
8.9.18 Answer Rate...................................................................................................... 8-103
8.9.19 Count of Callee Power-Off ................................................................................ 8-103
8.10 UE-Terminated Incoming Traffic.................................................................................. 8-103
8.10.1 Overview of MS_OFFICE_3G_INCTRM_TRAF............................................... 8-103
8.10.2 Count of Call Attempts ...................................................................................... 8-104
8.10.3 Count of Releases Before Ringing.................................................................... 8-105
8.10.4 Count of Terminal Application Failures............................................................. 8-106
8.10.5 Count of Common Resource Application Failures............................................ 8-107
8.10.6 Count of Callee Busy ........................................................................................ 8-108
8.10.7 Count of Mobile Callee Traffic Channel allocations Failures ............................ 8-109
8.10.8 Count of MS Unavailable .................................................................................. 8-110
8.10.9 Count of Connected Calls ................................................................................. 8-111
8.10.10 Count of Releases Before the Pickup............................................................. 8-112
8.10.11 Count of Long Time No Reply......................................................................... 8-113
8.10.12 Count of Mobile Callee Determined Busy....................................................... 8-114
8.10.13 Count of Answered Calls................................................................................. 8-115
8.10.14 Seizure Traffic ................................................................................................. 8-116
8.10.15 Connected Traffic............................................................................................ 8-117
8.10.16 Answered Traffic ............................................................................................. 8-118
8.10.17 Call Completion Rate ...................................................................................... 8-119
8.10.18 Answer Rate.................................................................................................... 8-119
8.11 UE-Terminated Traffic ................................................................................................. 8-120
8.11.1 Overview of MS_OFFICE_3G_TRM_TRAF ..................................................... 8-120
8.11.2 Count of Call Attempts ...................................................................................... 8-120
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
v
8.11.3 Count of Terminal Application Failures............................................................. 8-121
8.11.4 Count of Common Resource Application Failures............................................ 8-122
8.11.5 Count of Callee Busy ........................................................................................ 8-123
8.11.6 Count of Mobile Callee Trunk Resource Overflow............................................ 8-124
8.11.7 Count of Mobile Callee Traffic Channel allocations Failures ............................ 8-125
8.11.8 Count of MS Unavailable .................................................................................. 8-126
8.11.9 Count of Connected Calls ................................................................................. 8-127
8.11.10 Count of Releases Before the Pickup............................................................. 8-128
8.11.11 Count of Long Time No Reply......................................................................... 8-129
8.11.12 Count of Mobile Callee Determined Busy....................................................... 8-130
8.11.13 Count of Answered Calls................................................................................. 8-131
8.11.14 Seizure Traffic ................................................................................................. 8-132
8.11.15 Connected Traffic............................................................................................ 8-133
8.11.16 Answered Traffic ............................................................................................. 8-134
8.11.17 Call Completion Rate ...................................................................................... 8-135
8.11.18 Answer Rate.................................................................................................... 8-135
8.12 Outgoing Traffic ........................................................................................................... 8-136
8.12.1 Overview of MS_OFFICE_OUT_TRAF ............................................................ 8-136
8.12.2 Count of Seizure Attempts ................................................................................ 8-137
8.12.3 Count of Seizure ............................................................................................... 8-137
8.12.4 Count of Connected Calls ................................................................................. 8-138
8.12.5 Count of Answered Calls................................................................................... 8-139
8.12.6 Count of Not Answered Calls............................................................................ 8-140
8.12.7 Count of Releases Before Ringing.................................................................... 8-142
8.12.8 Count of Call Failures Due to Overload ............................................................ 8-142
8.12.9 Count of Call Failures Due to Network Management........................................ 8-144
8.12.10 Count of Outgoing Trunk Overflow ................................................................. 8-146
8.12.11 Count of Callee Busy ...................................................................................... 8-147
8.12.12 Count of Callee Busy in Toll Calls................................................................... 8-148
8.12.13 Count of Callee Busy in Local Calls................................................................ 8-149
8.12.14 Seizure Traffic ................................................................................................. 8-149
8.12.15 Answered Traffic ............................................................................................. 8-150
8.12.16 Count of Blocked Circuits................................................................................ 8-151
8.12.17 Call Completion Rate ...................................................................................... 8-151
8.12.18 Answer Rate.................................................................................................... 8-152
8.12.19 Count of Call Attempts .................................................................................... 8-152
8.12.20 Count of Failed Call Attempts Due to Common Resource Application Failure8-153
8.12.21 Count of Failed Call Attempts Due to Peer Office Congestion ....................... 8-154
8.12.22 Connected Traffic............................................................................................ 8-156
8.12.23 Count of Incomplete Addresses Received...................................................... 8-157
8.13 Connection Type.......................................................................................................... 8-160
8.13.1 Overview of MS_OFFICE_CALLNATURE_TRAF............................................ 8-160
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
vi
8.13.2 Count of Call Attempts ...................................................................................... 8-160
8.13.3 Count of Connected Calls ................................................................................. 8-161
8.13.4 Count of Answered Calls................................................................................... 8-162
8.13.5 Count of Barred Calls Due to Caller Service Restriction .................................. 8-163
8.13.6 Count of Releases Before Ringing.................................................................... 8-163
8.13.7 Count of Outgoing Trunk Overflow ................................................................... 8-164
8.13.8 Count of Callee Busy ........................................................................................ 8-165
8.13.9 Count of Releases Before the Pickup............................................................... 8-166
8.13.10 Count of Long Time No Reply......................................................................... 8-167
8.13.11 Seizure Traffic ................................................................................................. 8-168
8.13.12 Connected Traffic............................................................................................ 8-169
8.13.13 Answered Traffic ............................................................................................. 8-170
8.13.14 Call Completion Rate ...................................................................................... 8-171
8.13.15 Answer Rate.................................................................................................... 8-171
8.13.16 Count of MS Unavailable ................................................................................ 8-172
8.13.17 Count of Failed Call Attempts Due to Inter-Trunk Failure............................... 8-172
8.13.18 Count of Failed Call Attempts Due to Inter-Trunk Failure............................... 8-173
8.13.19 Count of Failed Call Attempts Due to Peer Office Congestion ....................... 8-174
8.13.20 Count of Mobile Callee Determined Busy....................................................... 8-175
8.14 Intra-Office Traffic ........................................................................................................ 8-176
8.14.1 Overview of MS_OFFICE_INT_MTM_TRAF.................................................... 8-176
8.14.2 Count of Call Attempts ...................................................................................... 8-177
8.14.3 Count of Releases Before Ringing.................................................................... 8-178
8.14.4 Count of Terminal Application Failures............................................................. 8-179
8.14.5 Count of Common Resource Application Failures............................................ 8-180
8.14.6 Count of Callee Busy ........................................................................................ 8-181
8.14.7 Count of Mobile Callee Trunk Resource Overflow............................................ 8-182
8.14.8 Count of Mobile Callee Traffic Channel allocations Failures ............................ 8-183
8.14.9 Count of MS Unavailable .................................................................................. 8-184
8.14.10 Count of Connected Calls ............................................................................... 8-185
8.14.11 Count of Releases Before the Pickup............................................................. 8-186
8.14.12 Count of Long Time No Reply......................................................................... 8-187
8.14.13 Count of Mobile Callee Determined Busy....................................................... 8-188
8.14.14 Count of Answered Calls................................................................................. 8-189
8.14.15 Seizure Traffic ................................................................................................. 8-190
8.14.16 Connected Traffic............................................................................................ 8-191
8.14.17 Answered Traffic ............................................................................................. 8-192
8.14.18 Call Completion Rate ...................................................................................... 8-193
8.14.19 Answer Rate.................................................................................................... 8-193
8.15 Call Forwarding Traffic................................................................................................. 8-194
8.15.1 Overview of MS_FORWARD_TRAF................................................................. 8-194
8.15.2 Count of Call Forwarding Attempts ................................................................... 8-194
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
vii
8.15.3 Count of Forwarded Calls ................................................................................. 8-195
8.15.4 Count of Answered Forwarded Calls ................................................................ 8-196
8.15.5 Count of Call Forwarding Seizure Traffic.......................................................... 8-197
8.15.6 Count of Call Forwarding Connected Traffic..................................................... 8-198
8.15.7 Call Forwarding Answered Traffic..................................................................... 8-199
8.16 Forwarded Subscriber Count....................................................................................... 8-200
8.16.1 Overview of MS_FORWARD_USER................................................................ 8-200
8.16.2 Count of Subscribers Forwarded to Destination ............................................... 8-200
8.17 Failure Causes of the Office ........................................................................................ 8-204
8.17.1 Overview of MS_FAULT_REASON_TRAF....................................................... 8-204
8.17.2 Count of Supplementary Service Setting Conflict ............................................. 8-208
8.17.3 Count of Supplementary Service Setting Successes ....................................... 8-208
8.17.4 Count of Supplementary Service Setting Failures ............................................ 8-209
8.17.5 Count of Supplementary Service Deregistration Successes ............................ 8-209
8.17.6 Count of Supplementary Service Deregistration Failures................................. 8-209
8.17.7 Count of Supplementary Service Authentication Successes............................ 8-210
8.17.8 Count of Supplementary Service Authentication Failures ................................ 8-210
8.17.9 Count of Supplementary Service Application Successes................................. 8-210
8.17.10 Count of Supplementary Service Application Failures.................................... 8-211
8.17.11 Count of Successes in Probing Malicious Calls.............................................. 8-211
8.17.12 Count of Failures in Probing Malicious Calls .................................................. 8-211
8.17.13 Count of MSC Congestions............................................................................. 8-212
8.17.14 Count of Long Time No Dialing....................................................................... 8-212
8.17.15 Count of Long Time No Reply......................................................................... 8-212
8.17.16 Count of Temporary Failures .......................................................................... 8-213
8.17.17 Count of Self-Test Successes......................................................................... 8-213
8.17.18 Count of Long Time No Messages ................................................................. 8-214
8.17.19 Count of Long Time No Ringing...................................................................... 8-214
8.17.20 Count of Long Time No Release..................................................................... 8-214
8.17.21 Count of Inband Signals.................................................................................. 8-215
8.17.22 Count of Continuity Check Failures ................................................................ 8-215
8.17.23 Count of Exceeding Max. Call Attempts ......................................................... 8-215
8.17.24 Count of Releases Before Ringing.................................................................. 8-216
8.17.25 Count of Releases Before the Pickup............................................................. 8-216
8.17.26 Count of Call Restrictions................................................................................ 8-216
8.17.27 Count of MSC Failures.................................................................................... 8-217
8.17.28 Count of Toll Calls to Busy Callee .................................................................. 8-217
8.17.29 Count of Local Calls to Busy Callee................................................................ 8-217
8.17.30 Count of Peer Office Congestion .................................................................... 8-218
8.17.31 Count of Call Failures...................................................................................... 8-218
8.17.32 Count of Contentions ...................................................................................... 8-219
8.17.33 Count of Invalid Numbers................................................................................ 8-219
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
viii
8.17.34 Count of Network Management Barring.......................................................... 8-219
8.17.35 Count of CPU Congestions and Overload ...................................................... 8-220
8.17.36 Count of No CR Resources............................................................................. 8-220
8.17.37 Count of No CCB Resources .......................................................................... 8-220
8.17.38 Count of Incoming Office CF Barring.............................................................. 8-221
8.17.39 Count of Dialing Time Out............................................................................... 8-221
8.17.40 Count of Signaling Failures............................................................................. 8-221
8.17.41 Count of Black List Calls Barred ..................................................................... 8-222
8.17.42 Count of Caller Number Identification Failures ............................................... 8-222
8.17.43 Count of No A Interface Resource for A Bearer Service ................................ 8-222
8.17.44 Count of No A Interface Resources ................................................................ 8-223
8.17.45 Count of CUG Service Incompatible............................................................... 8-223
8.17.46 Count of Unknown CUG.................................................................................. 8-223
8.17.47 Count of CUG Unselected............................................................................... 8-224
8.17.48 Count of CUG Outgoing Calls Barred............................................................. 8-224
8.17.49 Count of CUG Incoming Calls Barred............................................................. 8-224
8.17.50 Count of CUG Supplementary Service Failures ............................................. 8-225
8.17.51 Count of CUG Destination Incompatible......................................................... 8-225
8.17.52 Count of Released Calls ................................................................................. 8-225
8.17.53 Count of Switchover Successes...................................................................... 8-226
8.17.54 Count of Switchover Failures .......................................................................... 8-226
8.17.55 Count of Call Restriction Duration Timeout..................................................... 8-226
8.17.56 Count of Termination Resource Application Failures...................................... 8-227
8.17.57 Count of Callee Number Not Exist (Excluding Fixed-Line Numbers) ............. 8-227
8.17.58 Count of Mobile Callee No Reply.................................................................... 8-228
8.17.59 Count of Mobile Callee Incoming Call Restricted............................................ 8-228
8.17.60 Count of Call out Restrictions.......................................................................... 8-228
8.17.61 Count of Callee Unreachable.......................................................................... 8-229
8.17.62 Count of Calling Local Subscriber Without Area Code................................... 8-229
8.17.63 Count of Mobile Callee Busy........................................................................... 8-229
8.17.64 Count of Mobile Callee Power-Off................................................................... 8-230
8.17.65 Count of Required Function Not Applied ........................................................ 8-230
8.17.66 Count of Toll Calls Without 0 ........................................................................ 8-230
8.17.67 Count of CF Conflict ........................................................................................ 8-231
8.17.68 Count of Failures in HLR Obtaining Route Information .................................. 8-231
8.17.69 Count of All Outgoing Calls Barred by Operators ........................................... 8-232
8.17.70 Count of All Outgoing International Calls Barred by Operators ...................... 8-232
8.17.71 Count of All Outgoing International Calls Barred by Subscribers ................... 8-232
8.17.72 Count of BOIC-exHC Barred by Subscribers.................................................. 8-233
8.17.73 Count of BOIC-exHC Barred by Operators..................................................... 8-233
8.17.74 Count of All Incoming Calls Barred by Operators ........................................... 8-233
8.17.75 Count of Operators Barring Entertainment Console....................................... 8-234
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
ix
8.17.76 Count of Operators Barring Announcement Console ..................................... 8-234
8.17.77 Count of Subscriber Roaming Out .................................................................. 8-234
8.17.78 Count of All National Toll Calls Barred by Operators...................................... 8-235
8.17.79 Count of Cause Unknown Failures ................................................................. 8-235
8.17.80 Count of Unallocated Numbers....................................................................... 8-235
8.17.81 Count of No Route to Specified Transit Network ............................................ 8-236
8.17.82 Count of No Route to Destination ................................................................... 8-236
8.17.83 Count of Sending Private Tone....................................................................... 8-237
8.17.84 Count of Wrongly Dialed Numbers of Toll Call Prefix ..................................... 8-237
8.17.85 Count of Unacceptable Paths ......................................................................... 8-237
8.17.86 Count of Calls Connected and Delivered on Established Route .................... 8-238
8.17.87 Count of Calls Barred by Operators................................................................ 8-238
8.17.88 Count of Circuits Reserved for Reusing.......................................................... 8-238
8.17.89 Count of Normally cleared Calls...................................................................... 8-239
8.17.90 Count of Callee Determined Busy................................................................... 8-239
8.17.91 Count of No Reply........................................................................................... 8-239
8.17.92 Count of No Response.................................................................................... 8-240
8.17.93 Count of Callee Absent ................................................................................... 8-240
8.17.94 Count of Calls Rejected .................................................................................. 8-240
8.17.95 Count of Number Changed ............................................................................. 8-241
8.17.96 Count of No Idle Circuits ................................................................................. 8-241
8.17.97 Count of RAB Pre-Empted.............................................................................. 8-241
8.17.98 Count of Callee Failures.................................................................................. 8-242
8.17.99 Count of Invalid Number Formats ................................................................... 8-242
8.17.100 Count of Facilities Rejected .......................................................................... 8-242
8.17.101 Count of Responses to STATUS ENQUIRY................................................. 8-243
8.17.102 Count of Normally cleared Calls.................................................................... 8-243
8.17.103 Count of Unavailable Circuits........................................................................ 8-243
8.17.104 Count of Network Failures............................................................................. 8-244
8.17.105 Count of Contemporary Failures................................................................... 8-244
8.17.106 Count of MSC Failures.................................................................................. 8-245
8.17.107 Count of Accessed Messages Discarded ..................................................... 8-245
8.17.108 Count of Unavailable Routes ........................................................................ 8-245
8.17.109 Count of Unavailable Paths........................................................................... 8-246
8.17.110 Count of Unavailable Resources .................................................................. 8-246
8.17.111 Count of No Suitable Service Quality............................................................ 8-246
8.17.112 Counts of Facility Applied Not Preserved Before.......................................... 8-247
8.17.113 Count of CUG Outgoing Call Restriction....................................................... 8-247
8.17.114 Count of CUG Incoming Call Restriction....................................................... 8-247
8.17.115 Count of Bearer Capability Authorized.......................................................... 8-248
8.17.116 Count of No Available Bearer Capability....................................................... 8-248
8.17.117 Count of No Suitable Service or Optional Project ......................................... 8-248
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
x
8.17.118 Count of Bearer Capability Not Implemented ............................................... 8-249
8.17.119 Count of Path Type Not Implemented........................................................... 8-249
8.17.120 Count of AOC Service Request Failures ...................................................... 8-250
8.17.121 Count of ACM Equaling or Greater Than ACM max..................................... 8-250
8.17.122 Count of Requested Equipment Not Implemented ....................................... 8-250
8.17.123 Count of Restricted Bearer Capability........................................................... 8-251
8.17.124 Count of IWF Resource Unavailable............................................................. 8-251
8.17.125 Count of Service or Optional Project Not Implemented................................ 8-251
8.17.126 Count of Invalid Call Reference Values ........................................................ 8-252
8.17.127 Count of Identified Route Not Exist ............................................................... 8-252
8.17.128 Count of Callee not CUG Subscriber ............................................................ 8-252
8.17.129 Count of Incompatible Terminals .................................................................. 8-253
8.17.130 Count of CUG Not Exist ................................................................................ 8-253
8.17.131 Count of Invalid Transit Network Selection................................................... 8-253
8.17.132 Count of Invalid Messages............................................................................ 8-254
8.17.133 Count of Non-Existent or Not Implemented Message Types........................ 8-254
8.17.134 Count of Non-Existent or Not Implemented Message Units ......................... 8-255
8.17.135 Count of Timeout Recoveries........................................................................ 8-255
8.17.136 Count of Non-Existent or Not Implemented Parameters .............................. 8-255
8.17.137 Count of Messages Carrying Unidentified Parameters................................. 8-256
8.17.138 Count of Protocol errors................................................................................ 8-256
8.17.139 Count of Interworking.................................................................................... 8-256
8.18 Incoming Traffic ........................................................................................................... 8-257
8.18.1 Overview of MS_OFFICE_INC_TRAF.............................................................. 8-257
8.18.2 Count of Seizure ............................................................................................... 8-257
8.18.3 Count of Answered Calls................................................................................... 8-258
8.18.4 Count of Incomplete Numbers .......................................................................... 8-259
8.18.5 Count of Invalid Addresses ............................................................................... 8-261
8.18.6 Count of Failed Calls Due to Internal Failure.................................................... 8-263
8.18.7 Count of Call Failures Due to Overload ............................................................ 8-265
8.18.8 Count of Call Failures Due to Network Management........................................ 8-266
8.18.9 Seizure Traffic ................................................................................................... 8-268
8.18.10 Answered Traffic ............................................................................................. 8-268
8.18.11 Count of Circuits in Maintenance.................................................................... 8-269
8.18.12 Answer Rate.................................................................................................... 8-269
8.18.13 Count of Connected Calls ............................................................................... 8-270
8.18.14 Connected Traffic............................................................................................ 8-271
8.18.15 Call Completion Rate ...................................................................................... 8-271
8.18.16 Count of Callee Power-Off .............................................................................. 8-272
8.19 Source TMG Destination Route Traffic........................................................................ 8-273
8.19.1 Overview of MS_MGWID_ROUTE_TRAF........................................................ 8-273
8.19.2 Count of Seizure Attempts ................................................................................ 8-274
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
xi
8.19.3 Count of Seizure ............................................................................................... 8-275
8.19.4 Count of Ringings Received.............................................................................. 8-276
8.19.5 Count of Answered Calls................................................................................... 8-277
8.19.6 Call Completion Rate ........................................................................................ 8-278
8.19.7 Answer Rate...................................................................................................... 8-278
8.19.8 Seizure Traffic ................................................................................................... 8-279
8.19.9 Connected Traffic.............................................................................................. 8-280
8.19.10 Answered Traffic ............................................................................................. 8-280
8.19.11 Count of Outgoing Trunk Overflow ................................................................. 8-281
8.19.12 Count of Releases Before Ringing.................................................................. 8-282
8.19.13 Count of Releases Before the Pickup............................................................. 8-283
8.19.14 Count of Callee No Reply................................................................................ 8-284
8.19.15 Count of Callee Determined Busy................................................................... 8-285
8.19.16 Count of Callee Busy ...................................................................................... 8-286
8.19.17 Count of Invalid Addresses ............................................................................. 8-287
8.19.18 Count of Paging No Reply............................................................................... 8-288
8.19.19 Count of Subscriber Absence ......................................................................... 8-289
8.19.20 Count of Subscriber Service Restricted.......................................................... 8-290
8.19.21 Count of Special Tones................................................................................... 8-291
8.19.22 Count of Peer Office Congestions .................................................................. 8-292
8.19.23 Count of Interworking Failures ........................................................................ 8-293
8.19.24 Count of Other Failures................................................................................... 8-294
8.19.25 Count of Re-Routing ....................................................................................... 8-294
8.19.26 Count of Re-Routing Failures.......................................................................... 8-296
8.19.27 Count of UMG Failures ................................................................................... 8-297
8.19.28 Count of Circuit All Busy ................................................................................. 8-298
8.20 Transit Traffic............................................................................................................... 8-300
8.20.1 Overview of MS_OFFICE_TRN_TRAF............................................................. 8-300
8.20.2 Count of Outgoing Trunk Seizure Attempts ...................................................... 8-300
8.20.3 Count of Outgoing Trunk Seizure...................................................................... 8-301
8.20.4 Count of Connected Calls ................................................................................. 8-302
8.20.5 Count of Answered Calls................................................................................... 8-303
8.20.6 Count of Releases Before Ringing.................................................................... 8-304
8.20.7 Count of Outgoing Trunk Overflow ................................................................... 8-305
8.20.8 Count of Callee Busy ........................................................................................ 8-306
8.20.9 Seizure Traffic ................................................................................................... 8-307
8.20.10 Connected Traffic............................................................................................ 8-308
8.20.11 Answered Traffic ............................................................................................. 8-309
8.20.12 Call Completion Rate ...................................................................................... 8-310
8.20.13 Answer Rate.................................................................................................... 8-310
8.20.14 Count of Call Attempts .................................................................................... 8-311
8.20.15 Count of Wrongly Dialed Numbers.................................................................. 8-311
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents

Huawei Technologies Proprietary
xii
8.20.16 Count of Failed Call Attempts Due to Common Resource Application Failures8-312
8.20.17 Count of Peer Office Congestions .................................................................. 8-313
8.20.18 Count of Releases Before the Pickup............................................................. 8-314

Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-1
Chapter 8 Total Traffic of the Office
8.1 Overview of Measurement Set
This measurement set specifies the total traffic of the office. According to the
measurement of the total traffic of the office, all information including calling status,
calling service quality, and network quality in all directions can be obtained. This
information facilitates network optimization and upgrade.
The names and meanings are listed in the following table.
Name Description
MS_OFFICE_2G_ORGOUT_TRAF MS-originated outgoing traffic
MS_OFFICE_2G_ORG_TRAF MS-originated traffic
MS_OFFICE_2G_INCTRM_TRAF MS-terminated incoming traffic
MS_OFFICE_2G_TRM_TRAF MS-terminated traffic
MS_VP_3G_ORG_TRAF 3G VP subscriber originated traffic
MS_VP_3G_TRM_TRAF 3G VP subscriber terminated traffic
MS_OFFICE_3G_ORGOUT_TRAF UE-originated outgoing traffic
MS_OFFICE_3G_ORG_TRAF UE-originated traffic
MS_OFFICE_3G_INCTRM_TRAF UE-terminated incoming traffic
MS_OFFICE_3G_TRM_TRAF UE-terminated traffic
MS_OFFICE_OUT_TRAF Outgoing traffic
MS_OFFICE_CALLNATURE_TRAF Connection type
MS_OFFICE_INT_MTM_TRAF Intra-office traffic
MS_FORWARD_TRAF Call forwarding traffic
MS_FORWARD_USER Forwarded subscriber count
MS_FAULT_REASON_TRAF Failure causes of the office
MS_OFFICE_INC_TRAF Incoming traffic
MS_MGWID_ROUTE_TRAF Source TMG destination route traffic
MS_OFFICE_TRN_TRAF Transit traffic

Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-2
8.2 MS-Originated Outgoing Traffic
8.2.1 Overview of MS_OFFICE_2G_ORGOUT_TRAF
The names and meanings are listed in the following table.
Name Description
CA10 Count of call attempts
WDN10 Count of wrongly dialed numbers
ABR10 Count of releases before ringing
TAF10 Count of terminal application failures
CRU10 Count of common resource application failures
TO10 Count of last-choice route overflow
EC10 Count of peer office congestions
CB10 Count of callee busy
ALT10 Count of connected calls
AAR10 Count of releases before the pickup
RNA10 Count of long time no reply
ANS10 Count of answered calls
SU10 Seizure traffic
ALTU10 Connected traffic
ANSU10 Answered traffic
ALTR10 Call completion rate
ANSR10 Answer rate

8.2.2 Count of Call Attempts
I. Entity Name
CA10
II. Description
It is the count of call attempts initiated by the RNS and found to be outgoing ones
through DN analysis.
III. Measurement Point
It is measured when the MSC finds out a call originated by the BSS to be an outgoing
one according to the called number analysis.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-3
See point A in the following figure.
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
DTAP Connect Ack
ANM/ANC
REL

IV. Formula
None
8.2.3 Count of Wrongly Dialed Numbers
I. Entity Name
WDN10
II. Description
It is the count of call connection failures due to wrong numbers dialed by mobile callers.
III. Measurement Point
It is measured when the MSC receives the ADI or UNN message (TUP signaling).
See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-4
MSC Server MSC Server
ACM
DTAP SETUP
IAM
B
REL
RLC
RNC

It is measured when the number dialing time exceeds the time set on the internal
timer of the MSC. See point B in the following figure.
MSC Server MSC Server
ACM
DTAP SETUP
IAM
B
REL
RLC
RNC

It is measured when the MSC receives the REL message from the terminating
office. The cause value in the message is 129 (unallocated number) or 156
(incomplete number). See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-5
MSC Server MSC Server
ACM
DTAP SETUP
IAM
B
REL
RLC
RNC

IV. Formula
None
8.2.4 Count of Releases Before Ringing
I. Entity Name
ABR10
II. Description
It is the count of mobile caller releases before the callees' phones ring (the callee may
be either a non-local PSTN or mobile subscriber).
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from a mobile
caller before the call is connected. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-6
MSC Server MSC Server
RNC/BSC
ACM
DTAP SETUP
IAM
A REL
RLC
DTAP
Disconnect

IV. Formula
None
8.2.5 Count of Terminal Application Failures
I. Entity Name
TAF10
II. Description
It is the count of call failures caused by Prepare Bearer failures on the MGW.
III. Measurement Point
It is measured when the MSC receives the Prepare Bearer Rsp message from the
MGW. The message contains failure information. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-7
MSC Server
MSC Server
BSC
ACM
DTAP SETUP
IAM
A
REL
DTAP Disconnect

IV. Formula
None
8.2.6 Count of Common Resource Application Failures
I. Entity Name
CRU10
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, bill pool, control table, and announcement resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-8
MSC Server
MSC Server
BSC
ACM
DTAP SETUP
IAM
A
REL
DTAP Disconnect

IV. Formula
None
8.2.7 Count of Last-Choice Route Overflow
I. Entity Name
TO10
II. Description
It is the count of failures when the MSC tries to seize the outgoing trunk for outgoing
calls.
III. Measurement Point
It is measured when the MSC fails to select a trunk in an outgoing call. See point A in
the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-9
MSC Server
MSC Server
BSC
DTAP SETUP
IAM
A

IV. Formula
None
8.2.8 Count of Peer Office Congestions
I. Entity Name
EC10
II. Description
After the MSC sends the IAM or IAI to the peer office according to the routing
information in an outgoing call, the peer office or the terminating office returns an
unexpected backward message (excluding callee busy, invalid address) to indicate that
the call cannot be connected. This entity is the count of call connection failures in such
situation.
III. Measurement Point
It is measured in one of the following cases:
After sending the IAM, the MSC releases the call due to no response from the peer
office in a valid period.
The callee line is faulty.
The call connection fails.
The circuit group of the peer office is congested.
The switch of the peer office is congested.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-10
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
A
DTAP Disconnect

IV. Formula
None
8.2.9 Count of Callee Busy
I. Entity Name
CB10
II. Description
It is the count of call connections failed because callees are busy (in local or toll calls) in
the outgoing calls.
III. Measurement Point
It is measured when the MSC receives the STB, SLB (TUP), or REL (ISUP) message
from the terminating office in an outgoing call. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-11
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
A
REL
RLC
DTAP
Disconnect

IV. Formula
None
8.2.10 Count of Connected Calls
I. Entity Name
ALT10
II. Description
It is the count of DTAP Alerting messages sent to the callers in the outgoing calls.
III. Measurement Point
It is measured when the MSC sends the DTAP Alerting message to the mobile caller
after receiving the ACM. See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-12
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.2.11 Count of Releases Before the Pickup
I. Entity Name
AAR10
II. Description
It is the count of active releases by mobile callers before the pickup.
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from a mobile
caller before the callee picks up the phone. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-13
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
A
REL
DTAP
Disconnect
DTAP ALERTING
ANM/ANC

IV. Formula
None
8.2.12 Count of Long Time No Reply
I. Entity Name
RNA10
II. Description
It is the count of outgoing calls that are released because the callees do not answer till
timeout.
III. Measurement Point
It is measured when the MSC releases the call due to no ANM/ANC message
received from the callee in a valid period after the ACM. See point A in the
following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-14
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
A
REL
DTAP ALERTING
RLC
ANM/ANC

It is measured when the MSC releases the call after receiving the ACM and REL
messages from the callee. The cause value in REL message is 146
(CV_NO_RESPOND) or 147 (CV_NO_ACKNOWLEGE). See point A in the
following figure.
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
A
REL
DTAP ALERTING
RLC
ANM/ANC

IV. Formula
None
8.2.13 Count of Answered Calls
I. Entity Name
ANS10
II. Description
It is the count of outgoing calls answered.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-15
III. Measurement Point
It is measured when the MSC receives the DTAP Connect Ack message sent by an
mobile caller. See point C in the following figure. When receiving the ANC or ANN
message, the MSC sends the DTAP Connect message to the mobile caller. And then
the caller sends the DTAP Connect Ack to the MSC.
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.2.14 Seizure Traffic
I. Entity Name
SU10
II. Description
It is the traffic generated during the outgoing call attempts.
III. Measurement Point
It is measured from the moment the IAM or IAI message is sent to the destination MSC
to that the REL message is sent. The final result is indicated in Erlang. Point A in the
following figure is the start point of the measurement and call release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-16
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.2.15 Connected Traffic
I. Entity Name
ALTU10
II. Description
It is the traffic generated when outgoing calls are in the connected status.
III. Measurement Point
It is measured from the moment the ACM is received from the destination MSC to that
the REL message is sent. The final result is indicated in Erlang. Point B in the following
figure is the start point of the measurement and call release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-17
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.2.16 Answered Traffic
I. Entity Name
ANSU10
II. Description
It is the traffic generated when outgoing calls are in the answered status.
III. Measurement Point
It is measured from the moment the Answer signal is received from the destination
MSC to that the REL message is sent. The final result is indicated in Erlang. Point C in
the following figure is the start point of the measurement and call release is the end
point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-18
MSC Server MSC Server
BSC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.2.17 Call Completion Rate
I. Entity Name
ALTR10
II. Description
Answer rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is a calculated value.
IV. Formula
ALTR10 = ALT10/CA10
8.2.18 Answer Rate
I. Entity Name
ANSR10
II. Description
Answer rate = Count of answered calls/Count of call attempts
III. Measurement Point
It is a calculated value.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-19
IV. Formula
ANSR10 = ANS10/CA10
8.3 MS-Originated Traffic
8.3.1 Overview of MS_OFFICE_2G_ORG_TRAF
The names and meanings are listed in the following table.
Name Description
CA3 Count of call attempts
MAF3 Count of mobile caller authentication failures
MSCF3 Count of mobile caller ciphering mode setting failures
MB3 Count of mobile caller barring
MBTO3 Count of mobile caller trunk resource overflow
MASF3 Count of mobile caller traffic channel allocations failures
WDN3 Count of wrongly dialed numbers
ABR3 Count of releases before ringing
SNB3 Count of terminal application failures
CRU3 Count of common resource application failures
ALT3 Count of connected calls
ANS3 Count of answered calls
SU3 Seizure traffic
AU3 Connected traffic
ANU3 Answered traffic
AR3 Call completion rate
ANR3 Answer rate
ID3 Count of callee power-off

8.3.2 Count of Call Attempts
I. Entity Name
CA3
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-20
II. Description
It is the count of call attempts originated by the MSs in the local MSC, regardless of the
terminating MSCs.
III. Measurement Point
It is measured when the MSC receives the layer-3 CM Service Request message.
IV. Formula
None
8.3.3 Count of Mobile Caller Authentication Failures
I. Entity Name
MAF3
II. Description
It is the count of failed calls originated by the MSs in the local MSC due to
authentication failures.
III. Measurement Point
When receiving the AUTHENTICATION_RESPONSE message from the MS, the
MSC checks whether the XRES or SRES (for GSM network) is correct. If not, the
MSC returns a CM Service Reject message and begins the measurement.
It is measured when the MSC does not receive the
AUTHENTICATION_RESPONSE message from the MS in a valid period.
IV. Formula
None
8.3.4 Count of Mobile Caller Ciphering Mode Setting Failures
I. Entity Name
MSCF3
II. Description
It is the count of failed calls originated by MSs due to ciphering mode setting failures.
III. Measurement Point
It is measured when the MSC receives the CIPHER MODE REJECT message from the
BSS after sending the CIPHER MODE COMMAND message to the BSS of the MS.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-21
IV. Formula
None
8.3.5 Count of Mobile Caller Barring
I. Entity Name
MB3
II. Description
It is the count of failed calls due to the bearer capability or originating MS service
restriction, such as Bearer service not provisioned, Teleservice not provisioned, or
BAOC.
III. Measurement Point
It is measured when the call is released due to the restriction subscribed by the caller.
SETUP
O_MS MSC Server
A
RELEASE
VLR
ObtainSubscriberParaOutgoingCall
RELEASE COMPLETE

IV. Formula
None
8.3.6 Count of Mobile Caller Trunk Resource Overflow
I. Entity Name
MBTO3
II. Description
It is the count of failed calls originated by MSs due to all trunks busy on the interface A,
which makes the MSC fail to send the PREPARE BEARER REQ message to the MGW.
III. Measurement Point
It is measured when the MSC fails to allocate terrestrial channels before sending the
BSSMAP ASSIGN REQUEST message to the BSS of the mobile caller.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-22
SETUP
O_BSS MSC Server MGW
A
PREPARE BEARER REQ
PREPARE BEARER RSP
A1

IV. Formula
None
8.3.7 Count of Mobile Caller Traffic Channel allocations Failures
I. Entity Name
MASF3
II. Description
It is the count of failed call attempts caused by unsuccessful voice channel allocations
from the MSC to the BSC for the mobile callers.
III. Measurement Point
It is measured when the MSC receives the ASSIGN FAILURE message from the BSC
of the mobile caller after sending the BSSMAP ASSIGNMENT REQUEST message to
this BSC. The allocation includes advanced allocation and delayed allocation.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-23
BSSMAP ASSIGNMENT REQUEST
O_BSS MSC Server
BSSMAP ASSIGNMENT FAILURE
A

IV. Formula
None
8.3.8 Count of Wrongly Dialed Numbers
I. Entity Name
WDN3
II. Description
It is the count of wrong numbers dialed by local MSs, including the following three
cases.
The MSC fails to analyze the called number because the number is incomplete
and cannot be determined.
After confirming that the called number is MSISDN, the MSC fails to obtain the
routing information from the HLR. The callee location is unknown.
The MSC obtains the outgoing routing from the HLR, however, the terminating
office returns the ADI (invalid address), UNN (unallocated number, TUP), or REL
(unallocated number, incomplete number, ISUP) message.
III. Measurement Point
It is measured in one of the following cases.
The MSC fails to analyze the called number and the destination is unknown.
The MSC receives the Routing Failure message from the MAP.
The calling side is CM, and the call is released due to unavailable called number,
unallocated called number, invalid number format, or long time no dialing.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-24
8.3.9 Count of Releases Before Ringing
I. Entity Name
ABR3
II. Description
It is the count of mobile caller releases before the callees' phones ring.
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect, DTAP RELEASE, or
DTAP_RELEASE_CMP message from a mobile caller before the call is connected.
O_MS MSC Server
A
DISCONNECT / RELEASE
/ RELEASE COMPLETE
SETUP
Before ALERTING

IV. Formula
None
8.3.10 Count of Terminal Application Failures
I. Entity Name
SNB3
II. Description
It is the count of failed calls originated by the local MSs. The calls fail because the MSC
fails to request the MGW for the Termination resources.
III. Measurement Point
It is measured when the MSC fails to request the Reserve circuit from the MGW. See
point A1 in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-25
SETUP
O_BSS MSC Server MGW
A
PREPARE BEARER REQ
PREPARE BEARER RSP
A1

IV. Formula
None
8.3.11 Count of Common Resource Application Failures
I. Entity Name
CRU3
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, bill pool, control table, and announcement resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-26
SETUP
O_MS MSC Server
A
REALEASE COMPLETE

IV. Formula
None
8.3.12 Count of Connected Calls
I. Entity Name
ALT3
II. Description
It is the count of DTAP Alerting messages sent to the MSs.
III. Measurement Point
It is measured when the MSC sends the DTAP Alerting message to the mobile caller
after receiving the ACM from the terminating office in an inter-office call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-27
ALERTING
O_UE MSC Server
A
CONNECT
B
CONNECT ACK
ACM
ANM

It is measured when the MSC sends the DTAP Alerting message to the mobile caller
after receiving the DTAP Alerting message from the mobile callee in an intra-office call.
IV. Formula
None
8.3.13 Count of Answered Calls
I. Entity Name
ANS3
II. Description
It is the count of MS-originated calls answered.
III. Measurement Point
In an outgoing call, when receiving the ANC/ANN (TUP) or ANM (ISUP) message from
the terminating office, the MSC sends the DTAP Connect message to the mobile caller.
After receiving the DTAP Connect ACK message from the mobile caller, the MSC
begins the measurement.
In an incoming call, when receiving the DTAP Connect message from the mobile callee,
the MSC sends the DTAP Connect message to the mobile caller and begins the
measurement.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-28
ALERTING
O_UE MSC Server
A
CONNECT
B
CONNECT ACK
ACM
ANM

IV. Formula
None
8.3.14 Seizure Traffic
I. Entity Name
SU3
II. Description
It is the traffic generated from originating MS starting call attempt to call release.
III. Measurement Point
It measures the interval between relevant messages in a measurement period. It is
measured from the moment the DTAP Setup message is sent to that the CLEAR
COMMAND is sent. The final result is indicated in Erlang.
IV. Formula
None
8.3.15 Connected Traffic
I. Entity Name
AU3
II. Description
It is the traffic generated when incoming calls initiated by the MSs are in the connected
status. The measurement begins from the moment the phone rings to that the call is
released.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-29
III. Measurement Point
It is measured from the moment the DTAP Alerting message is received to that the
CLEAR COMMAND message is received. The final result is indicated in Erlang.
IV. Formula
None
8.3.16 Answered Traffic
I. Entity Name
ANU3
II. Description
It is the traffic generated when VP calls initiated by the local MSs are in the answered
status.
III. Measurement Point
It is measured from the moment the CONNECT ACKNOWLEDGE message is received
to that the CLEAR COMMAND message is received. The final result is indicated in
Erlang.
IV. Formula
None
8.3.17 Call Completion Rate
I. Entity Name
AR3
II. Description
Answer rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is a calculated value.
IV. Formula
AR3 = ALT3/CA3
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-30
8.3.18 Answer Rate
I. Entity Name
ANR3
II. Description
Answer rate = Count of answered calls/Count of call attempts
III. Measurement Point
It is a calculated value.
IV. Formula
ANR3 = ANS3/CA3
8.3.19 Count of Callee Power-Off
I. Entity Name
ID3
II. Description
It is the count of failed call connections (during called number analysis in MSC) due to
callees power-off.
III. Measurement Point
When the MSC analyzes the called number and queries the MSRN of the callee from
the HLR. The HLR returns an indication of callee power-off. The call connection fails
and the measurement begins.
IV. Formula
None
8.4 MS-Terminated Incoming Traffic
8.4.1 Overview of MS_OFFICE_2G_INCTRM_TRAF
The names and meanings are listed in the following table.
Name Description
CA14 Count of call attempts
ABR14 Count of releases before ringing
TAF14 Count of terminal application failures
CRU14 Count of common resource application failures
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-31
Name Description
CB14 Count of callee busy
MBTO14 Count of mobile callee trunk resource overflow
MAF14 Count of mobile callee traffic channel allocations failures
MNR14 Count of MS unavailable
ALT14 Count of connected calls
AAR14 Count of releases before the pickup
RNA14 Count of long time no reply
MDB14 Count of mobile callee determined busy
ANS14 Count of answered calls
SU14 Seizure traffic
ALTU14 Connected traffic
ANSU14 Answered traffic
ALTR14 Call completion rate
ANSR14 Answer rate

8.4.2 Count of Call Attempts
I. Entity Name
CA14
II. Description
It is the count of incoming trunk call attempts in which the callees are found out to be the
local MSs.
III. Measurement Point
It is measured when the MSC confirms the callee is an MS according to the MSRN of
the callee. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-32
MSC Server MSC Server
A
BSC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.4.3 Count of Releases Before Ringing
I. Entity Name
ABR14
II. Description
It is the count of active releases by the callers before calls are connected.
III. Measurement Point
It is measured when the MSC receives the call release message from a mobile caller
before the call is connected. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-33
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
DTAP ALERTING
REL

IV. Formula
None
8.4.4 Count of Terminal Application Failures
I. Entity Name
TAF14
II. Description
It is the count of call failures caused by Prepare Bearer failures on the MGW.
III. Measurement Point
It is measured when the MSC receives the Prepare Bearer Rsp message from the
MGW. The message contains failure information. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-34
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
DTAP ALERTING
REL
DTAP Disconnect

IV. Formula
None
8.4.5 Count of Common Resource Application Failures
I. Entity Name
CRU14
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, bill pool, control table, and announcement resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-35
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
DTAP ALERTING
REL
DTAP Disconnect

IV. Formula
None
8.4.6 Count of Callee Busy
I. Entity Name
CB14
II. Description
It is the count of incoming call connections failed because the mobile callees are busy
(in session).
III. Measurement Point
After getting the MSRN from the HLR, the MSC sends the message send info for
incoming/outgoing call to the VLR. The VLR returns a message to indicate that the
callee is busy, and then the MSC begins the measurement. See point A in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-36
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
When the MSC obtains the
MSRN, and the VLR returns a
message indicating callee busy.

IV. Formula
None
8.4.7 Count of Mobile Callee Trunk Resource Overflow
I. Entity Name
MBTO14
II. Description
It is the count of times when resources are unavailable for the incoming calls.
III. Measurement Point
It is measured when the MSC fails to allocate an A interface circuit for the callee. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-37
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
A interface circuits
allocation failure
DTAP ALERTING
A

IV. Formula
None
8.4.8 Count of Mobile Callee Traffic Channel allocations Failures
I. Entity Name
MAF14
II. Description
It is the count of failed call attempts caused by unsuccessful voice channel allocations
for the mobile callees in the incoming calls.
III. Measurement Point
It is measured when the MSC receives the BSSMAP ASSIGN FAILURE from the BSC.
Or it is measured at the timeout of the assignment timer. See point A in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-38
A
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
DTAP ALERTING
Called traffic channels
allocation failure

IV. Formula
None
8.4.9 Count of MS Unavailable
I. Entity Name
MNR14
II. Description
It is the count of failed incoming call connections due to the paging failures.
III. Measurement Point
It is measured when the MSC does not receive the Paging Response message from
the BSC of the mobile callee after sending the BSSMAP Paging message to the BSC in
an incoming call. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-39
A
MSC Server MSC Server
A
BSC
Mobile subscriber
unreachable
DTAP SETUP
DTAP PAGING
DTAP PAGING_RSP

IV. Formula
None
8.4.10 Count of Connected Calls
I. Entity Name
ALT14
II. Description
It is the count of messages indicating that the calls are connected.
III. Measurement Point
It is measured when the MSC receives the DTAP Alerting message in an incoming call.
See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-40
MSC Server MSC Server
A
BSC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.4.11 Count of Releases Before the Pickup
I. Entity Name
AAR14
II. Description
It is the count of active releases by the fixed-line callers before the mobile callees
pickup the phones in the incoming calls.
III. Measurement Point
After receiving the DTAP Alerting message from the mobile callee, the MSC sends
ringback tone to the caller. Before receiving the Connect message from the mobile
callee, the MSC receives the REL message from the caller. The measurement begins.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-41
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
DTAP ALERTING
REL
DTAP PAGING_RSP
ACM
DTAP CONNECT

IV. Formula
None
8.4.12 Count of Long Time No Reply
I. Entity Name
RNA14
II. Description
It is the count of outgoing calls that are released because the callees do not answer till
timeout.
III. Measurement Point
It is measured when the MSC releases the call due to no DTAP Alerting message
received from the callee in a valid period after the DTAP Alerting message. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-42
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
DTAP ALERTING
DTAP PAGING_RSP
ACM
DTAP CONNECT
DTAP DISCONNECT

It is measured when the MSC releases the call after receiving the DTAP Connect
and DTAP Disconnect messages from the callee. The cause value in DTAP
Disconnect message is 146 (CV_NO_RESPOND) or 147
(CV_NO_ACKNOWLEGE). See point A in the following figure.
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
DTAP ALERTING
DTAP PAGING_RSP
ACM
DTAP CONNECT
DTAP DISCONNECT
ANM/ANC

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-43
8.4.13 Count of Mobile Callee Determined Busy
I. Entity Name
MDB14
II. Description
It is the count of incoming calls directly rejected by the mobile callees after the ringing.
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from the callee
after the ringing. See point A in the following figure.
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
DTAP ALERTING
DTAP PAGING_RSP
ACM
DTAP CONNECT
DTAP DISCONNECT

IV. Formula
None
8.4.14 Count of Answered Calls
I. Entity Name
ANS14
II. Description
It is the count of incoming calls answered by the mobile callees.
III. Measurement Point
It is measured when the MSC sends the ANM to the originating office after receiving the
DTAP Connect message from the mobile callee. See point C in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-44
MSC Server MSC Server
A
BSC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.4.15 Seizure Traffic
I. Entity Name
SU14
II. Description
It is the traffic generated during the incoming call attempts.
III. Measurement Point
It is measured from the moment the IAM or IAI message is received to that the REL
message is received. The final result is indicated in Erlang. (ITU-T Rec. Q.722). Point A
in the following figure is the start point of the measurement and call release is the end
point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-45
MSC Server MSC Server
A
BSC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.4.16 Connected Traffic
I. Entity Name
ALTU14
II. Description
It is the traffic generated when incoming calls are in the connected status.
III. Measurement Point
It is measured from the moment the DTAP Alerting message is received from the callee
to that the REL message is received. The final result is indicated in Erlang (ITU-T Rec.
Q.722). Point B in the following figure is the start point of the measurement and call
release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-46
MSC Server MSC Server
A
BSC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.4.17 Answered Traffic
I. Entity Name
ANSU14
II. Description
It is the traffic generated when incoming calls are in the answered status.
III. Measurement Point
It is measured from the moment the Answer signal message is received from the callee
to that the REL message is received. The final result is indicated in Erlang (ITU-T Rec.
Q.722). Point C in the following figure is the start point of the measurement and call
release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-47
MSC Server MSC Server
A
BSC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.4.18 Call Completion Rate
I. Entity Name
ALTR14
II. Description
Answer rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ALTR14 = ALT14/CA14
8.4.19 Answer Rate
I. Entity Name
ANSR14
II. Description
Answer rate = Count of answered calls/Count of call attempts
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-48
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ANSR14 = ANS14/CA14
8.5 MS-Terminated Traffic
8.5.1 Overview of MS_OFFICE_2G_TRM_TRAF
The names and meanings are listed in the following table.
Name Description
CA19 Count of call attempts
TAF19 Count of terminal application failures
CRU19 Count of common resource application failures
CB19 Count of callee busy
MBTO19 Count of mobile callee trunk resource overflow
MAF19 Count of mobile callee traffic channel allocations failures
MNR19 Count of MS unavailable
ALT19 Count of connected calls
AAR19 Count of releases before the pickup
RNA19 Count of long time no reply
MDB19 Count of mobile callee determined busy
ANS19 Count of answered calls
SU19 Seizure traffic
ALTU19 Connected traffic
ANSU19 Answered traffic
ALTR19 Call completion rate
ANSR19 Answer rate

8.5.2 Count of Call Attempts
I. Entity Name
CA19
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-49
II. Description
It is the count of call attempts in which the callees are local MSs.
III. Measurement Point
It is measured after the VDB checks whether the number carried in the message is a
MSRN and before the Paging message is sent. At the same time, the MSC resets the
indicator. The callee may be in the local MSC or in another one. See point A in the
following figure.
BSC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
Incoming IAM or local SETUP
DTAP PAGING
DTAP PAGING_RSP
A

IV. Formula
None
8.5.3 Count of Terminal Application Failures
I. Entity Name
TAF19
II. Description
It is the count of Termination preparation failures on the MGW in 2G mobile terminated
calls.
III. Measurement Point
It is measured when the MSC fails to apply for the internal common resources in an 2G
mobile terminated call. The callee may be in the local MSC or in another one. See point
A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-50
BSC MSC Server
DTAP ALERTING
A
XXX
REL / DTAP DISCONNECT
DTAP DISCONNECT
Incoming IAM or local SETUP

IV. Formula
None
8.5.4 Count of Common Resource Application Failures
I. Entity Name
CRU19
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, bill pool, and control table resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources. The
callee may be in the local MSC or in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-51
BSC MSC Server
DTAP ALERTING
A
XXX
REL / DTAP DISCONNECT
DTAP DISCONNECT
Incoming IAM or local SETUP

IV. Formula
None
8.5.5 Count of Callee Busy
I. Entity Name
CB19
II. Description
It is the count of call connections failed because 2G callees are busy.
III. Measurement Point
The callee may be in the local MSC or in another one. See point A in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-52
BSC MSC Server
A
XXX
DTAP SETUP
The MSC obtains the MSRN, and
the VLR returns a message
indicating callee busy.
Incoming IAM or local SETUP

IV. Formula
None
8.5.6 Count of Mobile Callee Trunk Resource Overflow
I. Entity Name
MBTO19
II. Description
It is the count of failed local MSs terminated calls due to all trunks busy on the interface
A.
III. Measurement Point
It is measured when the MSC fails to allocate terrestrial channels before sending the
BSSMAP ASSIGN REQUEST message to the BSS of the mobile callee. The callee
may be in the local MSC or in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-53
BSC MSC Server
A
XXX
DTAP SETUP
Trunk resource overflow
DTAP ALERTING
Incoming IAM or local SETUP

IV. Formula
None
8.5.7 Count of Mobile Callee Traffic Channel allocations Failures
I. Entity Name
MAF19
II. Description
It is the count of failed call attempts caused by unsuccessful voice channel allocations
for the mobile callees.
III. Measurement Point
It is measured when the MSC receives the ASSIGN FAILURE message from the BSC
of the mobile callee after sending the BSSMAP ASSIGN REQUEST message to this
BSC. The allocation includes advanced allocation and delayed allocation. Or it is
measured at the timeout of the assignment timer. The callee may be in the local MSC or
in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-54
BSC MSC Server
A
XXX
DTAP SETUP
Called traffic channels
allocation failure
DTAP ALERTING
Incoming IAM or local SETUP

IV. Formula
None
8.5.8 Count of MS Unavailable
I. Entity Name
MNR19
II. Description
It is the count of failed incoming call connections due to the paging failures.
III. Measurement Point
It is measured when the MSC does not receive the Paging Response message after
sending the Paging message to the RNC or BSC of the mobile callee in an incoming
call. The callee may be in the local MSC or in another one. See point A in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-55
BSC MSC Server
A
XXX
DTAP PAGING
DTAP PAGING_RSP
Mobile subscriber
unreachable
Incoming IAM or local SETUP

IV. Formula
None
8.5.9 Count of Connected Calls
I. Entity Name
ALT19
II. Description
It is the count of DTAP Alerting messages received from the callees in the incoming 2G
calls.
III. Measurement Point
It is measured when the MSC receives the DTAP ALERTING message from the mobile
callee. The callee may be in the local MSC or in another one. See point B in the
following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-56
BSC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.5.10 Count of Releases Before the Pickup
I. Entity Name
AAR19
II. Description
It is the count of active releases by the callers before the mobile callees pickup the
phones in the 2G incoming calls.
III. Measurement Point
It is measured when the caller hooks on after the MSC receives the DTAP Altering
message but not the Connect message from the mobile callee. The callee may be in
the local MSC or in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-57
BSC MSC Server
DTAP ALERTING
DTAP SETUP
XXX
ACM / DTAP ALERTING
A
DTAP CONNECT
REL / DTAP DISCONNECT
RLC / DTAP RELEASE
Incoming IAM or local SETUP

IV. Formula
None
8.5.11 Count of Long Time No Reply
I. Entity Name
RNA19
II. Description
It is the count of incoming calls not answered by the 2G mobile callees till timeout.
III. Measurement Point
It is measured when the MSC releases the call due to no DTAP Connect message
received from the callee in a valid period after the DTAP Alerting message. The callee
may be in the local MSC or in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-58
BSC MSC Server
DTAP ALERTING
DTAP SETUP
XXX
ACM / DTAP ALERTING
A
DTAP CONNECT
DTAP DISCONNECT
DTAP RELEASE
Long time no reply
Incoming IAM or local SETUP

IV. Formula
None
8.5.12 Count of Mobile Callee Determined Busy
I. Entity Name
MDB19
II. Description
It is the count of incoming calls directly rejected by the 2G mobile callees after the
ringing.
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from the callee
after the ringing. The callee may be in the local MSC or in another one. See point A in
the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-59
BSC MSC Server
DTAP ALERTING
DTAP SETUP
XXX
ACM / DTAP ALERTING
A
DTAP CONNECT
DTAP DISCONNECT(CV_BUSY/
CV_USR_BUSY)
DTAP RELEASE
Incoming IAM or local SETUP

IV. Formula
None
8.5.13 Count of Answered Calls
I. Entity Name
ANS19
II. Description
It is the count of incoming calls answered by the 2G mobile callees.
III. Measurement Point
It is measured when the MSC receives the DTAP Connect message from the mobile
callee. The callee may be in the local MSC or in another one. See point C in the
following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-60
BSC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.5.14 Seizure Traffic
I. Entity Name
SU19
II. Description
It is the traffic generated during the incoming call attempts in which the callees are MSs.
III. Measurement Point
It measures the interval between relevant messages in a measurement period. In
internal MSC call connection, if the CM in the NSS is in the call originated status
(CM_MM_CONNECTION), the MSC begins the measurement. The measurement
stops when the CM shifts to idle state after the call is released. The final result is
indicated in Erlang (3GPP TS 25.413, GSM 08.08).
The callee may be in the local MSC or in another one. Point A in the following figure is
the start point of the measurement and call release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-61
BSC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.5.15 Connected Traffic
I. Entity Name
ALTU19
II. Description
It is the traffic generated when incoming calls terminated by MSs are in the connected
status. The measurement begins from the moment the phone rings to that the call is
released.
III. Measurement Point
It measures the interval between relevant messages in a measurement period. For
GSM system, the MSC begins the measurement from the moment the MSC receives
the DTAP Alerting message to that the CLEAR COMMAND message is received. The
final result is indicated in Erlang (3GPP TS 24.008, 3GPP TS25.413, GSM08.08).
The callee may be in the local MSC or in another one. Point B in the following figure is
the start point of the measurement and call release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-62
BSC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.5.16 Answered Traffic
I. Entity Name
ANSU19
II. Description
It is the traffic generated when incoming calls terminated by MSs are in the connected
status. The measurement begins from the moment the call is answered to that the call
is released.
III. Measurement Point
It measures the interval between relevant messages in a measurement period. For
GSM system, the MSC begins the measurement from the moment the MSC receives
the CONNECT ACKNOWLEDGE message to that the CLEAR COMMAND message is
received. The final result is indicated in Erlang (3GPP TS 24.008, 3GPP TS25.413,
GSM08.08).
The callee may be in the local MSC or in another one. Point C in the following figure is
the start point of the measurement and call release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-63
BSC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.5.17 Call Completion Rate
I. Entity Name
ALTR19
II. Description
Answer rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ALTR19 = ALT19/CA19
8.5.18 Answer Rate
I. Entity Name
ANSR19
II. Description
Answer rate = Count of answered calls/Count of call attempts
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-64
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ANSR19 = ANS19/CA19
8.6 3G VP Subscriber Originated Traffic
8.6.1 Overview of MS_VP_3G_ORG_TRAF
This section includes the following entities: UE VP calls, call attempts, connected calls,
answered calls, and traffic. The parameter protocols include 3GPP TS26110 and 3GPP
TS 26111.
The names and meanings are listed in the following table.
Name Description
CA196 Count of VP call attempts
ALT196 Count of VP connected calls
ANS196 Count of VP answered calls
BNS196 Count of failures due to bearer capability
SU196 Seizure traffic
AU196 VP connected traffic
ANU196 VP answered traffic
AR196 VP call completion rate
ANR196 VP answer rate

8.6.2 Count of VP Call Attempts
I. Entity Name
CA196
II. Description
It is the count of VP call attempts originated by the local MSs.
III. Measurement Point
It is measured when the MSC finds that the BC in the caller data received is multimedia
BC. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-65
SETUP
O_UE MSC Server
A
SubscriberPara
VLR
ObtainSubscriberParaOutgoingCall
B
CONNECT
C
CONNECT ACK
ALERTING
CALL PROCEEDING

IV. Formula
None
8.6.3 Count of VP Connected Calls
I. Entity Name
ALT196
II. Description
It is the count of connected VP calls originated by the local MSs.
III. Measurement Point
It is measured when the call switches to the CM_CALL_DELIVERED state after the
O_UE receives the ALERTING/ACM message in an outgoing mobile caller VP call. See
point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-66
SETUP
O_UE MSC Server
A
SubscriberPara
VLR
ObtainSubscriberParaOutgoingCall
B
CONNECT
C
CONNECT ACK
ALERTING
CALL PROCEEDING

IV. Formula
None
8.6.4 Count of VP Answered Calls
I. Entity Name
ANS196
II. Description
It is the count of answered VP calls originated by the local MSs.
III. Measurement Point
It is measured when the call switches to the CALL CONNECT IND state after the O_UE
receives the CONNECT/ANM message in an outgoing mobile caller VP call. See point
C in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-67
SETUP
O_UE MSC Server
A
SubscriberPara
VLR
ObtainSubscriberParaOutgoingCall
B
CONNECT
C
CONNECT ACK
ALERTING
CALL PROCEEDING

IV. Formula
None
8.6.5 Count of Failures Due to Bearer Capability
I. Entity Name
BNS196
II. Description
It is the count of failed outgoing mobile caller VP calls due to no bearer services
registered.
III. Measurement Point
It is measured when the MSC receives the REL message from the MAP for a call
started by a local MS with the release reason of no bearer capability.
SETUP
O_UE MSC Server
A
RELEASE
VLR
ObtainSubscriberParaOutgoingCall

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-68
8.6.6 Seizure Traffic
I. Entity Name
SU196
II. Description
It is the traffic generated from the start of outgoing VP call attempts initiated by local
MSs to the releases.
III. Measurement Point
It is measured from when the MSC finds that the BC in the caller data received is
multimedia BC until the call is released. The unit is Erlang.
IV. Formula
None
8.6.7 VP Connected Traffic
I. Entity Name
AU196
II. Description
It is the traffic generated when VP calls initiated by the local MSs are in the connected
status.
III. Measurement Point
The MSC begins the measurement from the moment it receives the DTAP Alerting or
ACM message to that the call is released. The unit is Erlang.
IV. Formula
None
8.6.8 VP Answered Traffic
I. Entity Name
ANU196
II. Description
It is the traffic generated when VP calls initiated by local MSs are in the answered
status.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-69
III. Measurement Point
The MSC begins the measurement from the moment it receives the DTAP Connect or
ANM message to that the call is released. The unit is Erlang.
IV. Formula
None
8.6.9 VP Call Completion Rate
I. Entity Name
AR196
II. Description
VP call completion rate = Count of VP connected calls/Count of VP call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
AR196 = ALT196/CA196.
8.6.10 VP Answer Rate
I. Entity Name
ANR196
II. Description
VP answer rate = Count of VP answered calls/Count of VP call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ANR196 = ANS196/CA196
8.7 3G VP Subscriber Terminated Traffic
8.7.1 Overview of MS_VP_3G_TRM_TRAF
This section includes the following entities: UE VP calls, call attempts, connected calls,
answered calls, and traffic. The parameter protocols include 3GPP TS26110 and 3GPP
TS 26111.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-70
The names and meanings are listed in the following table.
Name Description
CA197 Count of VP call attempts
ALT197 Count of VP connected calls
ANS197 Count of VP answered calls
BNS197 Count of failures due to bearer capability
SU197 Seizure traffic
AU197 VP connected traffic
ANU197 VP answered traffic
AR197 VP call completion rate
ANR197 VP answer rate

8.7.2 Count of VP Call Attempts
I. Entity Name
CA197
II. Description
It is the count of incoming VP call attempts.
III. Measurement Point
It is measured when the MSC finds that the BC in the caller data or the
CALL-CONFIRM message received is multimedia BC. See point A in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-71
SETUP
T_UE MSC Server
A
B
CONNECT
C
CONNECT ACK
ALERTING
CALL CONFIRMED

IV. Formula
None
8.7.3 Count of VP Connected Calls
I. Entity Name
ALT197
II. Description
It is the count of connected incoming VP calls.
III. Measurement Point
It is measured when the MSC receives the ALERTING message from the MS in an
incoming VP call. See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-72
SETUP
T_UE MSC Server
A
B
CONNECT
C
CONNECT ACK
ALERTING
CALL CONFIRMED

IV. Formula
None
8.7.4 Count of VP Answered Calls
I. Entity Name
ANS197
II. Description
It is the count of answered incoming VP calls.
III. Measurement Point
It is measured when the MSC receives the CONNECT message from the MS in an
incoming VP call. See point C in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-73
SETUP
T_UE MSC Server
A
B
CONNECT
C
CONNECT ACK
ALERTING
CALL CONFIRMED

IV. Formula
None
8.7.5 Count of Failures Due to Bearer Capability
I. Entity Name
BNS197
II. Description
It is the count of failed incoming VP calls due to no bearer services registered.
III. Measurement Point
It is measured when the MSC receives the REL message from the MAP or the caller
with the release reason of no bearer capability.
PAGE RESPONSE
T_UE MSC Server
A
RELEASE
VLR/O_UE

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-74
8.7.6 Seizure Traffic
I. Entity Name
SU197
II. Description
It is the traffic generated during the incoming VP call attempts.
III. Measurement Point
It is measured from when the MSC finds that the BC in the caller data or the
CALL-CONFIRM message received is multimedia BC until the call is released. The unit
is Erlang.
IV. Formula
None
8.7.7 VP Connected Traffic
I. Entity Name
AU197
II. Description
It is the traffic generated when incoming VP calls are in the connected status.
III. Measurement Point
The MSC begins the measurement from the moment it receives the DTAP Alerting
message from the MS to that the call is released. The unit is Erlang.
IV. Formula
None
8.7.8 VP Answered Traffic
I. Entity Name
ANU197
II. Description
It is the traffic generated when incoming VP calls are in the answered status.
III. Measurement Point
The MSC begins the measurement from the moment it receives the DTAP Connect
message from the MS to that the call is released. The unit is Erlang.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-75
IV. Formula
None
8.7.9 VP Call Completion Rate
I. Entity Name
AR197
II. Description
VP call completion rate = Count of VP connected calls/Count of VP call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
AR197 = ALT197/CA197.
8.7.10 VP Answer Rate
I. Entity Name
ANR197
II. Description
VP answer rate = Count of VP answered calls/Count of VP call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ANR197 = ANS197/CA197
8.8 UE-Originated Outgoing Traffic
8.8.1 Overview of MS_OFFICE_3G_ORGOUT_TRAF
The names and meanings are listed in the following table.
Name Description
CA11 Count of call attempts
WDN11 Count of wrongly dialed numbers
ABR11 Count of releases before ringing
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-76
Name Description
TAF11 Count of terminal application failures
CRU11 Count of common resource application failures
TO11 Count of outgoing trunk overflow
EC11 Count of peer office congestions
CB11 Count of callee busy
ALT11 Count of connected calls
AAR11 Count of releases before the pickup
RNA11 Count of long time no reply
ANS11 Count of answered calls
SU11 Seizure traffic
ALTU11 Connected traffic
ANSU11 Answered traffic
ALTR11 Call completion rate
ANSR11 Answer rate

8.8.2 Count of Call Attempts
I. Entity Name
CA11
II. Description
It is the count of call attempts initiated by the RNS and found to be outgoing ones
through DN analysis.
III. Measurement Point
After the RNC initiates a call, the MSC analyzes the called number. After confirming the
call is an outgoing one, the MSC begins the measurement. See point A in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-77
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.8.3 Count of Wrongly Dialed Numbers
I. Entity Name
WDN11
II. Description
It is the count of call connection failures due to wrong numbers dialed by mobile callers.
III. Measurement Point
It is measured when the MSC receives the ADI or UNN message (TUP). See point
A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-78
MSC Server MSC Server
ACM
DTAP SETUP
IAM
A
REL
RLC
RNC

It is measured when the number dialing time exceeds the time set on the internal
timer of the MSC. See point A in the following figure.
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
A
REL
RLC

It is measured when the MSC receives the REL message from the terminating
office. The cause value in the message is 129 (unallocated number) or 156
(incomplete number). See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-79
MSC Server MSC Server
ACM
DTAP SETUP
IAM
A
REL
RLC
RNC

IV. Formula
None
8.8.4 Count of Releases Before Ringing
I. Entity Name
ABR11
II. Description
It is the count of mobile caller releases before the callees' phones ring (the callee may
be either a non-local PSTN or mobile subscriber).
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from a mobile
caller before the call is connected. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-80
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
A REL
RLC
DTAP
Disconnect

IV. Formula
None
8.8.5 Count of Terminal Application Failures
I. Entity Name
TAF11
II. Description
It is the count of call failures caused by Prepare Bearer failures on the MGW.
III. Measurement Point
It is measured when the MSC receives the Prepare Bearer Rsp message from the
MGW. The message contains failure information. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-81
MSC Server
MSC Server
RNC
ACM
DTAP SETUP
IAM
A
REL
DTAP Disconnect

IV. Formula
None
8.8.6 Count of Common Resource Application Failures
I. Entity Name
CRU11
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, bill pool, control table, and announcement resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-82
MSC Server
MSC Server
RNC
ACM
DTAP SETUP
IAM
A
REL
DTAP Disconnect

IV. Formula
None
8.8.7 Count of Outgoing Trunk Overflow
I. Entity Name
TO11
II. Description
It is the count of failures when the MSC tries to seize the outgoing trunk for outgoing
calls.
III. Measurement Point
It is measured when the MSC fails to select a trunk in an outgoing call. See point A in
the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-83
MSC Server
MSC Server
RNC
DTAP SETUP
IAM
A
Outgoing trunk
overflow

IV. Formula
None
8.8.8 Count of Peer Office Congestions
I. Entity Name
EC11
II. Description
After the MSC sends the IAM or IAI to the peer office according to the routing
information in an outgoing call, the peer office or the terminating office returns an
unexpected backward message (excluding callee busy, invalid address) to indicate that
the call cannot be connected. This entity is the count of call connection failures in such
situation.
III. Measurement Point
It is measured in one of the following cases.
After sending the IAM, the MSC releases the call due to no response from the peer
office in a valid period.
The callee line is faulty.
The call connection fails.
The circuit group of the peer office is congested.
The peer office is congested.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-84
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
A
DTAP Disconnect

IV. Formula
None
8.8.9 Count of Callee Busy
I. Entity Name
CB11
II. Description
It is the count of call connections failed because callees are busy in the outgoing calls.
III. Measurement Point
It is measured when the MSC receives the STB, SLB (TUP), or REL (ISUP) message
from the terminating office in an outgoing call. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-85
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
A
REL
RLC
DTAP Disconnect

IV. Formula
None
8.8.10 Count of Connected Calls
I. Entity Name
ALT11
II. Description
It is the count of DTAP Alerting messages sent to the callers in the outgoing calls.
III. Measurement Point
It is measured when the MSC sends the DTAP Alerting message to a mobile caller after
receiving the ACM. See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-86
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.8.11 Count of Releases Before the Pickup
I. Entity Name
AAR11
II. Description
It is the count of active releases by mobile callers before the pickup.
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from a mobile
caller before the callee picks up the phone. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-87
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
A
REL
DTAP Disconnect
DTAP ALERTING
ANM/ANC

IV. Formula
None
8.8.12 Count of Long Time No Reply
I. Entity Name
RNA11
II. Description
It is the count of outgoing calls that are released because the callees do not answer till
timeout.
III. Measurement Point
1) It is measured when the MSC releases the call due to no DTAP Connect message
received from the callee in a valid period after the ACM.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-88
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
A
REL
DTAP ALERTING
RLC
ANM/ANC

2) It is measured when the MSC releases the call after receiving the ACM and REL
messages from the callee. The cause value in REL message is 146
(CV_NO_RESPOND) or 147 (CV_NO_ACKNOWLEGE).
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
A
REL
DTAP ALERTING
RLC
ANM/ANC

IV. Formula
None
8.8.13 Count of Answered Calls
I. Entity Name
ANS11
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-89
II. Description
It is the count of outgoing calls answered.
III. Measurement Point
When receiving the ANC or ANN message, the MSC sends the DTAP Connect
message to the mobile caller. After receiving the DTAP Connect ACK message from
the mobile caller, the MSC begins the measurement. See point C in the following figure.
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.8.14 Seizure Traffic
I. Entity Name
SU11
II. Description
It is the traffic generated during the outgoing call attempts.
III. Measurement Point
It is measured from the moment the IAM or IAI message is sent to the destination MSC
to the moment the REL message is sent. The final result is indicated in Erlang (ITU-T
Rec. Q.722). Point A in the following figure is the start point of the measurement and
call release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-90
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.8.15 Connected Traffic
I. Entity Name
ALTU11
II. Description
It is the traffic generated when outgoing calls are in the connected status.
III. Measurement Point
It is measured from the moment the ACM is received from the destination MSC to that
the REL message is sent. The final result is indicated in Erlang (ITU-T Rec. Q.722).
Point B in the following figure is the start point of the measurement and call release is
the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-91
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.8.16 Answered Traffic
I. Entity Name
ANSU11
II. Description
It is the traffic generated when outgoing calls are in answered status.
III. Measurement Point
It is measured from the moment the Answer signal is received from the destination
MSC to that the REL message is sent. The final result is indicated in Erlang (ITU-T Rec.
Q.722). Point C in the following figure is the start point of the measurement and call
release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-92
MSC Server MSC Server
RNC
ACM
DTAP SETUP
IAM
DTAP ALERTING
DTAP CONNECT
A
B
C
REL
REL
DTAP Connect Ack
ANM/ANC

IV. Formula
None
8.8.17 Call Completion Rate
I. Entity Name
ALTR11
II. Description
Answer rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ALTR11 = ALT11/CA11
8.8.18 Answer Rate
I. Entity Name
ANSR11
II. Description
Answer rate = Count of answered calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-93
IV. Formula
ANSR11 = ANS11/CA11
8.9 UE-Originated Traffic
8.9.1 Overview of MS_OFFICE_3G_ORG_TRAF
The names and meanings are listed in the following table.
Name Description
CA4 Count of call attempts
MAF4 Count of mobile caller authentication failures
MSCF4 Count of mobile caller ciphering mode setting failures
MB4 Count of mobile caller barring
MBTO4 Count of mobile caller trunk resource overflow
MASF4 Count of mobile caller traffic channel allocations failures
WDN4 Count of wrongly dialed numbers
ABR4 Count of releases before ringing
SNB4 Count of terminal application failures
CRU4 Count of common resource application failures
ALT4 Count of connected calls
ANS4 Count of answered calls
SU4 Seizure traffic
AU4 Connected traffic
ANU4 Answered traffic
AR4 Call completion rate
ANR4 Answer rate
ID4 Count of callee power-off

8.9.2 Count of Call Attempts
I. Entity Name
CA4
II. Description
It is the count of call attempts originated by UEs, regardless of the terminating MSCs.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-94
III. Measurement Point
It is measured when the MSC confirms that it is a mobile originating call or an
emergency call after receiving a layer-3 CM Service Request message.
IV. Formula
None
8.9.3 Count of Mobile Caller Authentication Failures
I. Entity Name
MAF4
II. Description
It is the count of failed calls originated by the UEs in the local MSC due to
authentication failures.
III. Measurement Point
1) When receiving the AUTHENTICATION_RESPONSE message from the MS, the
MSC checks whether the XRES or SRES (for GSM network) is correct. If not, the
MSC returns a CM Service Reject message, and the measurement begins.
2) It is measured when the MSC does not receive the
AUTHENTICATION_RESPONSE message from the MS in a valid period.
3) It is measured when the MS returns the respond message which carries MAC
failure or synchronization failure.
IV. Formula
None
8.9.4 Count of Mobile Caller Ciphering Mode Setting Failures
I. Entity Name
MSCF4
II. Description
It is the count of failed calls originated by UEs due to ciphering mode setting failures.
III. Measurement Point
It is measured when the MSC receives the SECURITY MODE REJECT message from
the RNC after sending the SECURITY MODE COMMAND message to the RNC.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-95
8.9.5 Count of Mobile Caller Barring
I. Entity Name
MB4
II. Description
It is the count of failed calls due to the bearer capability or originating UE service
restriction, such as Bearer service not provisioned, Teleservice not provisioned, or
BAOC.
III. Measurement Point
It is measured when the call is released due to the restriction of the service subscribed
by the caller.
SETUP
O_UE MSC Server
A
RELEASE
VLR
ObtainSubscriberParaOutgoingCall
RELEASE COMPLETE

IV. Formula
None
8.9.6 Count of Mobile Caller Trunk Resource Overflow
I. Entity Name
MBTO4
II. Description
It is the count of failed calls originated by UEs due to Prepare Bearer failures on the
MGW.
III. Measurement Point
It is measured when the MSC fails to allocate terrestrial channels before sending the
RAB ASSIGN REQUEST message to the RNC of the mobile caller. See point A in the
following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-96
SETUP
O_RNC MSC Server MGW
A
PREPARE BEARER REQ
PREPARE BEARER RSP
A1

IV. Formula
None
8.9.7 Count of Mobile Caller Traffic Channel allocations Failures
I. Entity Name
MASF4
II. Description
It is the count of failed call attempts caused by unsuccessful voice channel allocations
for originating UEs in the incoming calls.
III. Measurement Point
It is measured when the MSC receives the ASSIGN FAILURE message from the RNC
of the mobile caller after sending the RAB ASSIGN REQUEST message to this RNC.
The allocation includes advanced allocation and delayed allocation.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-97
RAB ASSIGNMENT REQUEST
O_RNC MSC Server
RAB ASSIGNMENT RESPONSE
A

IV. Formula
None
8.9.8 Count of Wrongly Dialed Numbers
I. Entity Name
WDN4
II. Description
It is the count of wrong numbers dialed by UEs, including the following three cases.
The MSC fails to analyze the called number because the number is incomplete
and cannot be determined.
After confirming that the called number is MSISDN, the MSC fails to obtain the
routing information from the HLR. The callee location is unknown.
The MSC obtains the outgoing routing from the HLR, however, the terminating
office returns the ADI (invalid address), UNN (unallocated number, TUP), or REL
(unallocated number, incomplete number, ISUP) message.
III. Measurement Point
It is measured in one of the following cases.
The MSC fails to analyze the called number and the destination is unknown.
The MSC receives the Routing Failure message from the MAP.
The MSC receives the ADI, UNN (TUP) or REL (ISUP) message from the
terminating office in an outgoing call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-98
8.9.9 Count of Releases Before Ringing
I. Entity Name
ABR4
II. Description
It is the count of active releases by the local UEs before the callees phones ring.
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect, DTAP RELEASE, or
DTAP RELEASE COMPLETE message from a mobile caller before the call is
connected.
O_UE MSC Server
A
DISCONNECT / RELEASE
/ RELEASE COMPLETE
SETUP
Before ALERTING

IV. Formula
None
8.9.10 Count of Terminal Application Failures
I. Entity Name
SNB4
II. Description
It is the count of failed calls originated by the UEs. The calls fail due to the Prepare
Bearer failures on the MGW.
III. Measurement Point
It is measured when the MSC receives the Prepare Bearer Rsp message from the
MGW. The message contains failure information. See point A1 in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-99
SETUP
O_RNC MSC Server MGW
A
PREPARE BEARER REQ
PREPARE BEARER RSP
A1

IV. Formula
None
8.9.11 Count of Common Resource Application Failures
I. Entity Name
CRU4
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, bill pool, and control table resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources.
IV. Formula
None
8.9.12 Count of Connected Calls
I. Entity Name
ALT4
II. Description
It is the count of DTAP Alerting messages sent to the O_UEs in the outgoing calls.
III. Measurement Point
It is measured when the MSC sends the DTAP Alerting message to the mobile caller
after receiving the ACM from the terminating office in an inter-office call. It is measured
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-100
when the MSC sends the DTAP Alerting message to the mobile caller after receiving
the DTAP Alerting message from the mobile callee in an intra-office call.
ALERTING
O_UE MSC Server
A
CONNECT
B
CONNECT ACK
ACM
ANM

IV. Formula
None
8.9.13 Count of Answered Calls
I. Entity Name
ANS4
II. Description
It is the count of incoming UE-originated calls answered.
III. Measurement Point
In an outgoing call, when receiving the ANC/ANN (TUP) or ANM (ISUP) message from
the terminating office, the MSC sends the DTAP Connect message to the mobile caller
and begins the measurement. See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-101
ALERTING
O_UE MSC Server
A
CONNECT
B
CONNECT ACK
ACM
ANM

IV. Formula
None
8.9.14 Seizure Traffic
I. Entity Name
SU4
II. Description
It is the traffic generated from originating UE starting call attempt to call release.
III. Measurement Point
In internal MSC call connection, if the CM is in the call originated status
(CM_CALL_ORIGINATED), the MSC begins the measurement. The measurement
stops when the CM shifts to idle state after the call is released.
IV. Formula
None
8.9.15 Connected Traffic
I. Entity Name
AU4
II. Description
It is the traffic generated when incoming calls initiated by the UEs are in the connected
status. The measurement begins from the moment the phone rings to that the call is
released.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-102
III. Measurement Point
It is measured from the moment the DTAP Alerting message is received to that the IU
RELEASE COMMAND message is received. The final result is indicated in Erlang.
IV. Formula
None
8.9.16 Answered Traffic
I. Entity Name
ANU4
II. Description
It is the traffic generated when incoming calls initiated by UEs are in the connected
status. The measurement begins from the moment the call is answered to that the call
is released.
III. Measurement Point
It measures the interval between relevant messages in a measurement period. The
MSC begins the measurement from the moment the message CONNECT
ACKNOWLEDGE is received to that the message IU RELEASE COMMAND is sent.
The final result is indicated in Erlang.
IV. Formula
None
8.9.17 Call Completion Rate
I. Entity Name
AR4
II. Description
Call completion rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is a calculated value.
IV. Formula
AR4 = ALT4/CA4
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-103
8.9.18 Answer Rate
I. Entity Name
ANR4
II. Description
Answer rate = Count of answered calls/Count of call attempts
III. Measurement Point
It is a calculated value.
IV. Formula
ANR4 = ANS4/CA4
8.9.19 Count of Callee Power-Off
I. Entity Name
ID4
II. Description
It is the count of failed call connections (during called number analysis in MSC) due to
callees power-off.
III. Measurement Point
When the MSC analyzes the called number and queries the MSRN of the callee from
the HLR. The HLR returns an indication of callee power-off. The call connection fails
and the measurement begins.
IV. Formula
None
8.10 UE-Terminated Incoming Traffic
8.10.1 Overview of MS_OFFICE_3G_INCTRM_TRAF
The names and meanings are listed in the following table.
Name Description
CA15 Count of call attempts
ABR15 Count of releases before ringing
TAF15 Count of terminal application failures
CRU15 Count of common resource application failures
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-104
Name Description
CB15 Count of callee busy
MAF15 Count of mobile callee traffic channel allocations failures
MNR15 Count of MS unavailable
ALT15 Count of connected calls
AAR15 Count of releases before the pickup
RNA15 Count of long time no reply
MDB15 Count of mobile callee determined busy
ANS15 Count of answered calls
SU15 Seizure traffic
ALTU15 Connected traffic
ANSU15 Answered traffic
ALTR15 Call completion rate
ANSR15 Answer rate

8.10.2 Count of Call Attempts
I. Entity Name
CA15
II. Description
It is the count of incoming call attempts in which the callees are found to be local UEs
during called number analysis stage in MSC.
III. Measurement Point
It is measured when the MSC confirms the callee is a UE according to the MSRN of the
callee. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-105
MSC Server MSC Server
A
RNC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.10.3 Count of Releases Before Ringing
I. Entity Name
ABR15
II. Description
It is the count of active releases by the callers before calls are connected.
III. Measurement Point
It is measured when the MSC receives the call release message from a caller before
the call is connected. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-106
MSC Server MSC Server
A
RNC
IAM
DTAP SETUP
DTAP ALERTING
REL

IV. Formula
None
8.10.4 Count of Terminal Application Failures
I. Entity Name
TAF15
II. Description
It is the count of call failures caused by Prepare Bearer failures on the MGW.
III. Measurement Point
It is measured when the MSC receives the Prepare Bearer Rsp message from the
MGW. The message contains failure information. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-107
MSC Server MSC Server
A
RNC
IAM
DTAP SETUP
DTAP ALERTING
REL
DTAP Disconnect

IV. Formula
None
8.10.5 Count of Common Resource Application Failures
I. Entity Name
CRU15
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, bill pool, control table, and announcement resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-108
MSC Server MSC Server
A
RNC
IAM
DTAP SETUP
DTAP ALERTING
REL
DTAP Disconnect

IV. Formula
None
8.10.6 Count of Callee Busy
I. Entity Name
CB15
II. Description
It is the count of incoming calls failed because mobile callees are busy (in session).
III. Measurement Point
After getting the MSRN from the HLR, the MSC sends the message send info for
incoming call to the VLR. The VLR returns a message to indicate that the callee is busy,
and then the MSC begins the measurement. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-109
MSC Server MSC Server
A
RNC
IAM
DTAP SETUP
The MSC obtains the MSRN,
and the VLR returns a message
indicating callee busy.

IV. Formula
None
8.10.7 Count of Mobile Callee Traffic Channel allocations Failures
I. Entity Name
MAF15
II. Description
It is the count of failed call attempts caused by unsuccessful voice channel allocations
for mobile callees in the incoming calls.
III. Measurement Point
It is measured when the MSC receives the RAB ASSIGNMENT RESP (assignment
failure) message from the RNC. Or it is measured at the timeout of the assignment
timer. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-110
A
MSC Server MSC Server
A
RNC
IAM
DTAP SETUP
DTAP
ALERTING
Called traffic channels
allocation failure

IV. Formula
None
8.10.8 Count of MS Unavailable
I. Entity Name
MNR15
II. Description
It is the count of failed incoming call connections due to the paging failures.
III. Measurement Point
It is measured when the MSC does not receive the Paging Response message after
sending the Paging message to the RNC of the mobile callee in an incoming call. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-111
A
MSC Server MSC Server
A
RNC
Mobile subscriber
unreachable
DTAP SETUP
DTAP PAGING
DTAP PAGING_RSP

IV. Formula
None
8.10.9 Count of Connected Calls
I. Entity Name
ALT15
II. Description
It is the count of messages indicating that the calls are connected.
III. Measurement Point
It is measured when the MSC receives the DTAP Alerting message in an incoming call.
See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-112
MSC Server MSC Server
A
RNC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.10.10 Count of Releases Before the Pickup
I. Entity Name
AAR15
II. Description
It is the count of active releases by fixed-line callers before the mobile callees pickup
the phones in the incoming calls.
III. Measurement Point
After receiving the DTAP Alerting message from the mobile callee, the MSC sends the
ringback tone to the fixed-line caller. Before the mobile callee sends the Connect
message, the originating office sends the REL message. The MSC begins the
measurement. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-113
MSC Server MSC Server
A
RNC
IAM
DTAP SETUP
DTAP ALERTING
REL
DTAP PAGING_RSP
ACM
DTAP CONNECT

IV. Formula
None
8.10.11 Count of Long Time No Reply
I. Entity Name
RNA15
II. Description
It is the count of incoming calls not answered by the mobile callees till timeout.
III. Measurement Point
It is measured when the MSC releases the call due to no DTAP Connect message
received from the callee in a valid period after the DTAP Alerting message. See point A
in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-114
MSC Server MSC Server
A
RNC
IAM
DTAP SETUP
DTAP ALERTING
DTAP PAGING_RSP
ACM
DTAP CONNECT
DTAP DISCONNECT

It is measured when the MSC releases the call after receiving the DTAP Connect and
DTAP Disconnect messages from the callee. The cause value in DTAP Disconnect
message is 146 (CV_NO_RESPOND) or 147 (CV_NO_ACKNOWLEGE). See point A
in the following figure.
MSC Server MSC Server
A
BSC
IAM
DTAP SETUP
DTAP ALERTING
DTAP PAGING_RSP
ACM
DTAP CONNECT
DTAP DISCONNECT
ANM/ANC

IV. Formula
None
8.10.12 Count of Mobile Callee Determined Busy
I. Entity Name
MDB15
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-115
II. Description
It is the count of incoming calls directly rejected by the mobile callees after the ringing.
See point A in the following figure.
MSC Server MSC Server
A
RNC
IAM
DTAP SETUP
DTAP ALERTING
DTAP PAGING_RSP
ACM
DTAP CONNECT
DTAP DISCONNECT

III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from the callee
after the ringing. See point A in the following figure. The value of the message is
CV_USER_BUSY or CV_BUSY.
IV. Formula
None
8.10.13 Count of Answered Calls
I. Entity Name
ANS15
II. Description
It is the count of incoming calls answered by the mobile callees.
III. Measurement Point
It is measured when the MSC sends the ANM to the originating office after receiving the
DTAP Connect message from the mobile callee. See point C in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-116
MSC Server MSC Server
A
RNC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.10.14 Seizure Traffic
I. Entity Name
SU15
II. Description
It is the traffic generated during the incoming call attempts.
III. Measurement Point
It is measured from the moment the IAM or IAI message is received to that the REL
message is received. The final result is indicated in Erlang (ITU-T Rec. Q.722).
Point A in the following figure is the start point of the measurement and call release is
the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-117
MSC Server MSC Server
A
BSC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.10.15 Connected Traffic
I. Entity Name
ALTU15
II. Description
It is the traffic generated when incoming calls are in the connected status.
III. Measurement Point
It is measured from the moment the DTAP Alerting message is received from the callee
to that the REL message is received. The final result is indicated in Erlang (ITU-T Rec.
Q.722).
Point B in the following figure is the start point of the measurement and call release is
the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-118
MSC Server MSC Server
A
BSC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.10.16 Answered Traffic
I. Entity Name
ANSU15
II. Description
It is the traffic generated when incoming calls are in answered status.
III. Measurement Point
It is measured from the moment the Answer signal message is received from the callee
to that the REL message is received. The final result is indicated in Erlang (ITU-T Rec.
Q.722).
Point C in the following figure is the start point of the measurement and call release is
the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-119
MSC Server MSC Server
A
BSC
c
IAM
DTAP SETUP
DTAP ALERTING
DTAP CONNECT
B ACM
ANM/ANC

IV. Formula
None
8.10.17 Call Completion Rate
I. Entity Name
ALTR15
II. Description
Call completion rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ALTR15 = ALT15/CA15
8.10.18 Answer Rate
I. Entity Name
ANSR15
II. Description
Answer rate = Count of answered calls/Count of call attempts
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-120
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ANSR15 = ANS15/CA15
8.11 UE-Terminated Traffic
8.11.1 Overview of MS_OFFICE_3G_TRM_TRAF
The names and meanings are listed in the following table.
Name Description
CA20 Count of call attempts
TAF20 Count of terminal application failures
CRU20 Count of common resource application failures
CB20 Count of callee busy
MBTO20 Count of mobile callee trunk resource overflow
MAF20 Count of mobile callee traffic channel allocations failures
MNR20 Count of MS unavailable
ALT20 Count of connected calls
AAR20 Count of releases before the pickup
RNA20 Count of long time no reply
MDB20 Count of mobile callee determined busy
ANS20 Count of answered calls
SU20 Seizure traffic
ALTU20 Connected traffic
ANSU20 Answered traffic
ALTR20 Call completion rate
ANSR20 Answer rate

8.11.2 Count of Call Attempts
I. Entity Name
CA20
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-121
II. Description
It is the count of call attempts in which the callees are found out to be the local UEs.
III. Measurement Point
It is measured when the MSC receives the DTAP PAGING RSP message. At the same
time, the MSC resets the indicator. The callee may be in the local MSC or in another
one. See point A in the following figure.
RNC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.11.3 Count of Terminal Application Failures
I. Entity Name
TAF20
II. Description
It is the count of call failures caused by Prepare Bearer failures on the MGW.
III. Measurement Point
It is measured when the MGW prepares the trunk resource after receiving the
BEARER_INFO message in a 3G terminated call. The callee may be in the local MSC
or in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-122
RNC MSC Server
DTAP ALERTING
A
XXX
REL / DTAP DISCONNECT
DTAP DISCONNECT
Incoming IAM or local SETUP

IV. Formula
None
8.11.4 Count of Common Resource Application Failures
I. Entity Name
CRU20
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, bill pool, and control table resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources. The
callee may be in the local MSC or in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-123
RNC MSC Server
DTAP ALERTING
A
XXX
REL / DTAP DISCONNECT
DTAP DISCONNECT
Incoming IAM or local SETUP

IV. Formula
None
8.11.5 Count of Callee Busy
I. Entity Name
CB20
II. Description
It is the count of call connections failed because callees are busy.
III. Measurement Point
After getting the MSRN from the HLR, the MSC sends the message send info for
incoming/outgoing call setup to the VLR. The VLR returns a message to indicate that
the callee (no CF service) is busy, and then the MSC begins the measurement. The
callee may be in the local MSC or in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-124
RNC MSC Server
A
XXX
DTAP SETUP
The MSC obtains the MSRN,
and the VLR returns a message
indicating callee busy.
Incoming IAM or local SETUP

IV. Formula
None
8.11.6 Count of Mobile Callee Trunk Resource Overflow
I. Entity Name
MBTO20
II. Description
It is the count of times of failed terrestrial channel allocations for terminating UEs.
III. Measurement Point
It is measured when the MSC fails to allocate terrestrial channels before sending the
RAB ASSIGN REQUEST message to the RNC of the mobile callee. The callee may be
in the local MSC or in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-125
RNC MSC Server
A
XXX
DTAP SETUP
A interface circuits
allocation failure
DTAP ALERTING
Incoming IAM or local SETUP

IV. Formula
None
8.11.7 Count of Mobile Callee Traffic Channel allocations Failures
I. Entity Name
MAF20
II. Description
It is the count of failed call attempts caused by unsuccessful voice channel allocations
for the UEs.
III. Measurement Point
It is measured when the MSC receives the ASSIGN FAILURE message from the RNC
of the mobile callee after sending the RAB ASSIGN REQUEST message to this RNC.
The allocation includes advanced allocation and delayed allocation. Or it is measured
at the timeout of the assignment timer. The callee may be in the local MSC or in another
one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-126
RNC MSC Server
A
XXX
DTAP SETUP
Called traffic channels
allocation failure
DTAP ALERTING
Incoming IAM or local SETUP

IV. Formula
None
8.11.8 Count of MS Unavailable
I. Entity Name
MNR20
II. Description
It is the count of failed call connections due to the MSs unavailable.
III. Measurement Point
It is measured when the MSC does not receive the Paging Response message after
sending the Paging message to the RNC or BSC of the mobile callee in a call. The
callee may be in the local MSC or in another one. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-127
RNC MSC Server
A
XXX
DTAP PAGING
DTAP PAGING_RSP
Mobile subscriber
unreachable
Incoming IAM or local SETUP

IV. Formula
None
8.11.9 Count of Connected Calls
I. Entity Name
ALT20
II. Description
It is the count of DTAP Alerting messages received from the 3G callees in the incoming
calls.
III. Measurement Point
It is measured when the MSC receives the DTAP Alerting message. It is measured
when the status of the CM is CM_CALL_RECEIVED. The callee may be in the local
MSC or in another one. See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-128
RNC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.11.10 Count of Releases Before the Pickup
I. Entity Name
AAR20
II. Description
It is the count of active releases by non-local callers before the mobile callees pickup in
3G incoming calls.
III. Measurement Point
It is measured when the caller hooks on after the MSC receives the DTAP Altering
message but not the Connect message from the mobile callee. The callee may be in
the local MSC or in another one. See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-129
RNC MSC Server
DTAP ALERTING
DTAP SETUP
XXX
ACM / DTAP ALERTING
A
DTAP CONNECT
REL / DTAP DISCONNECT
RLC / DTAP RELEASE
Incoming IAM or local SETUP

IV. Formula
None
8.11.11 Count of Long Time No Reply
I. Entity Name
RNA20
II. Description
It is the count of incoming calls not answered by the 3G mobile callees till timeout.
III. Measurement Point
It is measured when the MSC receives the DISCONNECT message from the mobile
caller due to no DTAP Connect message received from the callee in a valid period after
the DTAP Alerting message. Or it is measured when the MSC releases the call due to
connection timeout. The callee may be in the local MSC or in another one. See point A
in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-130
RNC MSC Server
DTAP ALERTING
DTAP SETUP
XXX
ACM / DTAP ALERTING
A
DTAP CONNECT
DTAP DISCONNECT
DTAP RELEASE
Long time no reply
Incoming IAM or local SETUP

IV. Formula
None
8.11.12 Count of Mobile Callee Determined Busy
I. Entity Name
MDB20
II. Description
It is the count of incoming calls directly rejected by mobile callees after the ringing.
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from the callee
after the ringing. The callee may be in the local MSC or in another one. See point A in
the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-131
RNC MSC Server
DTAP ALERTING
DTAP SETUP
XXX
ACM / DTAP ALERTING
A
DTAP CONNECT
DTAP DISCONNECT(CV_BUSY/
CV_USR_BUSY)
DTAP RELEASE
Incoming IAM or local SETUP

IV. Formula
None
8.11.13 Count of Answered Calls
I. Entity Name
ANS20
II. Description
It is the count of incoming calls answered by the 3G mobile callees.
III. Measurement Point
It is measured when the MSC receives the DTAP Connect message from the mobile
callee. The callee may be in the local MSC or in another one. See point C in the
following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-132
RNC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.11.14 Seizure Traffic
I. Entity Name
SU20
II. Description
It is the traffic generated during the incoming call attempts in which the callees are UEs.
III. Measurement Point
It measures the interval between relevant messages in a measurement period. In
internal MSC call connection, if the CM is in the call originated status
(CM_MM_CONNECTION), the MSC begins the measurement. The measurement
stops when the CM shifts to idle state after the call is released. The final result is
indicated in Erlang (3GPP TS 25.413, GSM 08.08). The callee may be in the local MSC
or in another one. Point A in the following figure is the start point of the measurement
and call release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-133
RNC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.11.15 Connected Traffic
I. Entity Name
ALTU20
II. Description
It is the traffic generated when incoming UE calls are in the connected status.
III. Measurement Point
It measures the interval between relevant messages in a measurement period. When
the MSC receives the DTAP Alerting message and the CM is in the status of
CM_CALL_RECIEVED, the MSC begins the measurement. The measurement stops
when the CM shifts to idle state after the call is released. The final result is indicated in
Erlang (3GPP TS 24.008, 3GPP TS25.413, GSM08.08). The callee may be in the local
MSC or in another one. Point B in the following figure is the start point of the
measurement and call release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-134
RNC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.11.16 Answered Traffic
I. Entity Name
ANSU20
II. Description
It is the traffic generated when incoming UE calls are in the answered status.
III. Measurement Point
It measures the interval between relevant messages in a measurement period. When
the MSC receives the DTAP Connect message and the CM is in the status of
CM_CONNECT_REQUEST, the MSC begins the measurement. The measurement
stops when the CM shifts to idle state after the call is released. The final result is
indicated in Erlang (3GPP TS 24.008, 3GPP TS25.413, GSM08.08). The callee may be
in the local MSC or in another one. Point C in the following figure is the start point of the
measurement and call release is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-135
RNC MSC Server
DTAP ALERTING
DTAP SETUP
ACM / DTAP ALERTING
B
DTAP CONNECT
ANM / DTAP CONNECT
C
XXX
DTAP PAGING
DTAP PAGING_RSP
A
Incoming IAM or local SETUP

IV. Formula
None
8.11.17 Call Completion Rate
I. Entity Name
ALTR20
II. Description
Call completion rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ALTR20 = ALT20/CA20
8.11.18 Answer Rate
I. Entity Name
ANSR20
II. Description
Answer rate = Count of answered calls/Count of call attempts
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-136
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ANSR20 = ANS20/CA20
8.12 Outgoing Traffic
8.12.1 Overview of MS_OFFICE_OUT_TRAF
The names and meanings are listed in the following table.
Name Description
BID Count of call attempts
SEIZ Count of seizure
CNT Count of connected calls
ANS Count of answered calls
NANS Count of not answered calls
BRGABN Count of releases before ringing
ALBLCL Count of call failures due to overload
FWCTLCL Count of call failures due to network management
LRUOFL Count of outgoing trunk overflow
CBSY Count of callee busy
CTB Count of callee busy in toll calls
CLB Count of callee busy in local calls
SERL Seizure traffic
RERL Answered traffic
MNTCIR Count of blocked circuits
CNTR Call completion rate
ANSR Answer rate
CATS Count of call attempts
CRFS
Count of failed call attempts due to common resource
application failure
PCFS Count of failed call attempts due to peer office congestion
ATTR Connected traffic
RADI Count of incomplete addresses received

Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-137
8.12.2 Count of Seizure Attempts
I. Entity Name
BID
II. Description
It is the count of outgoing seizure attempts (without considering the caller attributes).
III. Measurement Point
It is measured when the MSC tries to seize a trunk circuit or BICC CIC for a call. It is
measured when the ISUP receives the Setup message. See point A in the following
figure.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
B
ANM
Connect
Connect Ack
ANM
Connect
Connect Ack
C
A

IV. Formula
None
8.12.3 Count of Seizure
I. Entity Name
SEIZ
II. Description
It is the count of successful seizures of the outgoing (bidirectional) trunk circuits or
BICC CIC. For SS7, It is the count of seizure ACK messages. For SS1, it is the count of
Setup messages. For BICC, It is the count of CIC seizure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-138
III. Measurement Point
It is measured when the call successfully seizes the outgoing trunk circuit or BICC CIC.
It is measured when the ISUP receives the Setup message. See point A in the following
figure.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
B
ANM
Connect
Connect Ack
ANM
Connect
Connect Ack
C
A

IV. Formula
None
8.12.4 Count of Connected Calls
I. Entity Name
CNT
II. Description
It is the count of ACMs received from the peer office of the callees (PSTN or GSM
subscribers) in the outgoing calls.
III. Measurement Point
It is measured when the ISUP receives the ACM (ITU-T Rec. Q.722) from the peer
office.
It is measured when the ISUP receives the ACM. See point A in the following table.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-139
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
B
ANM
Connect
Connect Ack
ANM
Connect
Connect Ack
C
A

IV. Formula
None
8.12.5 Count of Answered Calls
I. Entity Name
ANS
II. Description
It is the count of outgoing calls answered.
III. Measurement Point
It is measured after the MSC receives the ANC, ANN, or ANM message.
It is measured when the ISUP receives the ANM.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-140
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
B
ANM
Connect
Connect Ack
ANM
Connect
Connect Ack
C
A

IV. Formula
None
8.12.6 Count of Not Answered Calls
I. Entity Name
NANS
II. Description
It is the count of failed call attempts due to no replies from the callees, releases by the
callers, or other reasons. The preceding reasons are classified into one because the
callees are in other offices where the signaling cannot be distinguished. You can
calculate the calls by the following formula:
Count of not answered calls = Count of connected calls Count of answered calls.
III. Measurement Point
It is measured when the MSC releases the call due to no ANM received from the callee
in a valid period after the ACM.
1) Not answered calls (case 1)
The cause value of the REL message might be one of the following:
CV_NO_ACKNOWLEGE
CV_LONG_TIME_NO_ANSWER
CV_GSM_CLD_USER_NO_ACKNOWLEGE
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-141
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
REL
A
REL
Release
Release

2) Not answered calls (case 2)
The cause value of the REL message might be one of the following:
CV_RECOVERY_OF_TIME_OUT
CV_NO_ACKNOWLEGE
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
A
REL

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-142
8.12.7 Count of Releases Before Ringing
I. Entity Name
BRGABN
II. Description
It is the count of mobile caller releases before the callees' phones ring.
III. Measurement Point
Before receiving the ACM, the MSC sends the CLF or REL message.
See point A in the following figure.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
MSC ISUP(inc)
REL
A
REL
Release
Release

IV. Formula
None
8.12.8 Count of Call Failures Due to Overload
I. Entity Name
ALBLCL
II. Description
It is the count of failed calls due to CPU overload.
III. Measurement Point
It is measured when the call is released due to CPU overload.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-143
1) Call failures due to overload (case 1)
The cause value of the REL message is CV_CPU_OVERLAP.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
MSC ISUP(inc)
A
REL
Release

2) Call failures due to overload (case 2)
The cause value of the REL message is CV_CPU_OVERLAP.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
A
REL
Release

3) Call failures due to overload (case 3)
The cause value of the REL message is CV_CPU_OVERLAP.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-144
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
A
REL
Release
ANM
Connect
Connect
ANM

IV. Formula
None
8.12.9 Count of Call Failures Due to Network Management
I. Entity Name
FWCTLCL
II. Description
It is the count of failed calls due to network management.
III. Measurement Point
It is measured when the call is released due to the network management.
1) Call failure due to network management (case 1)
The cause value of the REL message is CV_NET_MANAGE_BARRING.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-145
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
MSC ISUP(inc)
A
REL
Release

2) Call failure due to network management (case 2)
The cause value of the REL message is CV_NET_MANAGE_BARRING.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
A
REL
Release

3) Call failure due to network management (case 3)
The cause value of the REL message is CV_NET_MANAGE_BARRING.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-146
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
A
REL
Release
ANM
Connect
Connect
ANM

IV. Formula
None
8.12.10 Count of Outgoing Trunk Overflow
I. Entity Name
LRUOFL
II. Description
It is the count of failures of trunk or BICC CIC seizure attempts originated by the MSC in
the outgoing calls.
III. Measurement Point
It is measured when the MSC fails to select an outgoing trunk or BICC CIC in an
outgoing call. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-147
IAM
MSC Server
A
MSC Server
Outgoing trunk
overflow

IV. Formula
None
8.12.11 Count of Callee Busy
I. Entity Name
CBSY
II. Description
It is the count of call connections failed because callees are busy.
III. Measurement Point
It is measured when the MSC receives the REL message from the peer office to
indicate that the callee is busy in an outgoing call. It includes the following cases.
1) Callee busy (case 1)
The cause value of the REL message is CV_BUSY.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-148
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
MSC ISUP(inc)
A
REL

2) Callee busy (case 2)
The cause value of the REL message is CV_BUSY.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
A
REL

IV. Formula
None
8.12.12 Count of Callee Busy in Toll Calls
I. Entity Name
CTB
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-149
II. Description
It is the count of calls failed because the callees are in toll calls..
III. Measurement Point
It is measured when the TUP receives the STB message from the peer office in an
outgoing call.
IV. Formula
None
8.12.13 Count of Callee Busy in Local Calls
I. Entity Name
CLB
II. Description
It is the count of failed calls due to callees in local call sessions.
III. Measurement Point
It is measured when the TUP receives the SLB message from the peer office in an
outgoing call.
IV. Formula
None
8.12.14 Seizure Traffic
I. Entity Name
SERL
II. Description
It is the traffic generated during the outgoing call attempts.
III. Measurement Point
It is measured from the moment the IAM or IAI message is sent to that the REL, CLF or
CBK message is received. The final result is indicated in Erlang (ITU-T Rec. Q.722).
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-150
IAM
MSC Server
MSC Server
REL
A
IAM
MSC Server
MSC Server
REL
A

IV. Formula
None
8.12.15 Answered Traffic
I. Entity Name
RERL
II. Description
It is the traffic generated when outgoing calls are in the answered status.
III. Measurement Point
It is measured from the moment the Answer signal is received from the destination
MSC to that the REL, CLF or CBK message is sent. The final result is indicated in
Erlang (ITU-T Rec. Q.722).
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-151
IAM
MSC Server
MSC Server
REL
A
ANM
REL
B
IAM
MSC Server
MSC Server
REL
A
ANM
REL
B

IV. Formula
None
8.12.16 Count of Blocked Circuits
I. Entity Name
MNTCIR
II. Description
It is the count of circuits that are in maintenance state on the outgoing (bidirectional)
trunk.
III. Measurement Point
It is measured when a circuit is in maintenance state.
IV. Formula
None
8.12.17 Call Completion Rate
I. Entity Name
CNTR
II. Description
Call completion rate = Count of connected calls/Count of call attempts
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-152
III. Measurement Point
It is calculated on the BAM.
IV. Formula
CNTR = CNT/CATS
8.12.18 Answer Rate
I. Entity Name
ANSR
II. Description
Answer rate = Count of answered calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ANSR = ANS/CATS
8.12.19 Count of Call Attempts
I. Entity Name
CATS
II. Description
It is the count of outgoing call attempts.
III. Measurement Point
After the caller initiates a call, the MSC analyzes the called number. After confirming the
call is an outgoing one, the MSC begins the measurement.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-153
IAM
MSC Server
MSC Server
A
IAM
MSC Server
MSC Server
A

IV. Formula
None
8.12.20 Count of Failed Call Attempts Due to Common Resource Application
Failure
I. Entity Name
CRFS
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, DTR, bill pool, and control table resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-154
IAM
MSC Server MSC Server
A
REL
RLC
ACM

IV. Formula
None
8.12.21 Count of Failed Call Attempts Due to Peer Office Congestion
I. Entity Name
PCFS
II. Description
After the MSC sends the IAM or IAI to the peer office according to the routing
information in an outgoing call, the peer office or the terminating office returns an
unexpected backward message (excluding callee busy, invalid address) to indicate that
the call cannot be connected. This entity is the count of call connection failures in such
situation.
III. Measurement Point
It is measured in one of the following cases.
Long time no reply.
Called line faulty.
Call connection failure.
Peer office circuit group congestion.
Dedicated signal tone sending failure.
Peer office congestion. See point A in the following figure.
The cause value of the REL message may be one of the following:
CV_EXCHANGE_FACILITY_SURGE
CV_NO_RESOURCE_AVAILABLE
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-155
CV_NO_ROUTE_TO_TERMINAL
CV_NO_ROUTE_AVAILABLE
CV_NO_ROUTE_OR_CIRCUIT_APPLIED_AVAILABLE
CV_REOUTE_IDENTEFIED_NOT_EXIST
CV_INVALID_TRANSMIT_NETWORK_SELECTION
1) Call failure due to peer office congestion (case 1)
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
MSC ISUP(inc)
A
REL

2) Call failure due to peer office congestion (case 2)
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-156
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
A
REL

IV. Formula
None
8.12.22 Connected Traffic
I. Entity Name
ATTR
II. Description
It is the traffic generated when outgoing calls are in the connected status.
III. Measurement Point
It is measured from the moment the ACM is received from the destination MSC to that
the REL, CLF, or CBK message is sent. The final result is indicated in Erlang (ITU-T
Rec. Q.722). Point A in the following figure is the start point of the measurement and B
or C is the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-157
IAM
MSC Server
MSC Server
REL
B
ACM
C
REL
A
IAM
MSC Server
MSC Server
REL
B
ACM
C
REL
A

IV. Formula
None
8.12.23 Count of Incomplete Addresses Received
I. Entity Name
RADI
II. Description
It is the count of failed calls due to incomplete numbers.
III. Measurement Point
It is measured when the MSC receives the REL message with the cause value address
incomplete (0011100) from the peer office.
1) Call failure due to incomplete number (case 1)
The cause value of the REL message is
CV_INVALID_FORMAT_OR_ADDRESS_NOT_ENOUGH.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-158
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
MSC ISUP(inc)
A
REL

2) Call failure due to incomplete number (case 2)
The cause value of the REL message is
CV_INVALID_FORMAT_OR_ADDRESS_NOT_ENOUGH.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
A
REL

3) Call failure due to incomplete number (case 3)
The value of the Release message is
CV_INVALID_FORMAT_OR_ADDRESS_NOT_ENOUGH.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-159
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
MSC ISUP(inc)
A
REL
Release
Release
REL

4) Call failure due to incomplete number (case 4)
The value of the Release message is
CV_INVALID_FORMAT_OR_ADDRESS_NOT_ENOUGH.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
MSC ISUP(inc)
A
REL
Release
Release
REL

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-160
8.13 Connection Type
8.13.1 Overview of MS_OFFICE_CALLNATURE_TRAF
The names and meanings are listed in the following table.
Name Description
PEGS Count of call attempts
CNT Count of connected calls
ANS Count of answered calls
BAR Count of barred calls due to caller service restriction
BRGABN Count of releases before ringing
LRUOFL Count of outgoing trunk overflow
CBSY Count of callee busy
ARGABN Count of releases before the pickup
LTNANS Count of long time no reply
SERL Seizure traffic
CERL Connected traffic
RERL Answered traffic
CNTR Call completion rate
ANSR Answer rate
CEUR Count of MS unavailable
CFITB Count of failed call attempts due to inter-trunk failure
CFBTB Count of failed call attempts due to inter-trunk failure
CFPOB Count of failed call attempts due to peer office congestion
CDBT Count of mobile callee determined busy

8.13.2 Count of Call Attempts
I. Entity Name
PEGS
II. Description
It is the count of call attempts in which the connection types are defined.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-161
III. Measurement Point
After receiving the IAM or DTAP SETUP message, the MSC analyzes the called
number. After confirming the connection type, the MSC begins the measurement.
The callee may be in the local MSC or in another one. If the callee is in another office,
see point A in the following figure. If the callee is a local MS, see point D in the following
figure.
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
D
DTAP ALERTING
IAM
ANM/ANC/ANN
C
A
B
E
F
DTAP SETUP
XXX
Incoming IAM or local SETUP
Incoming IAM or local SETUP

IV. Formula
None
8.13.3 Count of Connected Calls
I. Entity Name
CNT
II. Description
It is the count of DTAP Alerting messages or ACMs received from the peer office.
III. Measurement Point
It is measured when the MSC receives the ACM or the DTAP Alerting message from
the peer office.
The callee may be in the local MSC or in another one. If the callee is in another office,
see point B in the following figure. If the callee is a local MS, see point E in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-162
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
D
DTAP ALERTING
IAM
ANM/ANC/ANN
C
A
B
E
F
DTAP SETUP
XXX
Incoming IAM or local SETUP
Incoming IAM or local SETUP

IV. Formula
None
8.13.4 Count of Answered Calls
I. Entity Name
ANS
II. Description
It is the count of outgoing calls answered.
III. Measurement Point
For an outgoing call, it is measured when the MSC receives the ANC, ANN, or ANM
message. For an incoming call, it is measured when the MSC receives the DTAP
Connect message from the mobile callee.
The callee may be in the local MSC or in another one. If the callee is in another office,
see point C in the following figure. If the callee is a local MS, see point F in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-163
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
D
DTAP ALERTING
IAM
ANM/ANC/ANN
C
A
B
E
F
DTAP SETUP
XXX
Incoming IAM or local SETUP
Incoming IAM or local SETUP

IV. Formula
None
8.13.5 Count of Barred Calls Due to Caller Service Restriction
I. Entity Name
BAR
II. Description
It is the count of barred calls due to the caller service restrictions, such as Bearer
service not provisioned, Teleservice not provisioned, or BAOC.
III. Measurement Point
It is measured when the MSC receives the abnormal cause value of the release
message.
IV. Formula
None
8.13.6 Count of Releases Before Ringing
I. Entity Name
BRGABN
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-164
II. Description
It is the count of mobile caller releases before the callees' phones ring.
III. Measurement Point
It is measured when the MSC receives the REL or DTAP Disconnect message from a
caller before the call is connected.
The callee may be in the local MSC or in another one. If the callee is in another office,
see point A in the following figure. If the callee is a local MS, see point B in the following
figure.
MSC Server MSC Server
ACM
RNC/BSC
B
DTAP ALERTING
XXX
A
Incoming IAM or local SETUP
Incoming IAM or local SETUP
Incoming REL or local DTAP DISCONNECT
Incoming REL or local DTAP DISCONNECT

IV. Formula
None
8.13.7 Count of Outgoing Trunk Overflow
I. Entity Name
LRUOFL
II. Description
It is the count of failures when the MSC tries to seize the outgoing trunk for outgoing
calls.
III. Measurement Point
It is measured when the MSC fails to select a trunk in an outgoing call. See point A in
the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-165
MSC Server MSC Server
IAM
A
XXX
Outgoing trunk overflow
Incoming IAM or local SETUP

IV. Formula
None
8.13.8 Count of Callee Busy
I. Entity Name
CBSY
II. Description
It is the count of call connections failed because callees are busy.
III. Measurement Point
It is measured when the MSC receives the REL message from the terminating office or
from the mobile callee due to user busy.
The callee may be in the local MSC or in another one. If the callee is in another office,
see point A in the following figure. If the callee is a local MS, see point B in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-166
MSC Server MSC Server
REL
RNC/BSC
DTAP ALERTING
B
IAM
A
XXX
ACM
MT busy
Incoming IAM or local SETUP
Incoming IAM or local SETUP

IV. Formula
None
8.13.9 Count of Releases Before the Pickup
I. Entity Name
ARGABN
II. Description
It is the count of active releases by the incoming trunk before the pickup.
III. Measurement Point
It is measured when the callee receives the REL message from the incoming trunk
(including the RNC and BSC).
The callee may be in the local MSC or in another one. If the callee is in another office,
see point A in the following figure. If the callee is a local MS, see point B in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-167
MSC Server MSC Server
ACM
RNC/BSC
B
DTAP ALERTING
XXX
A
IAM
ANM
DTAP CONNECT
DTAP SETUP
Incoming IAM or local SETUP
Incoming IAM or local SETUP
Incoming REL or local DTAP DISCONNECT
Incoming REL or local DTAP DISCONNECT

IV. Formula
None
8.13.10 Count of Long Time No Reply
I. Entity Name
LTNANS
II. Description
It is the count of calls that are released because the callees do not answer till timeout.
III. Measurement Point
It is measured when the MSC releases the call due to no DTAP Connect message
received from the callee in a valid period.
The callee may be in the local MSC or in another one. For an incoming call, point A in
the following figure is the start point of the measurement. For an outgoing call from the
local MSC, point B in the following figure is the start point of the measurement.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-168
MSC Server MSC Server
ACM
RNC/BSC
B
DTAP ALERTING
XXX
A
ACM / DTAP ALERTING
IAM
ANM
DTAP CONNECT
DTAP SETUP
ACM / DTAP ALERTING
REL
DTAP DISCONNECT
Incoming IAM or local SETUP
Incoming IAM or local SETUP

IV. Formula
None
8.13.11 Seizure Traffic
I. Entity Name
SERL
II. Description
It is the traffic generated during the call attempts.
III. Measurement Point
It is measured from the moment the MSC defines the call attribute to that the REL
message is received. The final result is indicated in Erlang.
The callee may be in the local MSC or in another one. If the callee is in another office,
see point A in the following figure. If the callee is a local MS, see point D in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-169
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
D
DTAP ALERTING
IAM
ANM/ANC/ANN
C
A
B
E
F
DTAP SETUP
XXX
Incoming IAM or local SETUP
Incoming IAM or local SETUP

IV. Formula
None
8.13.12 Connected Traffic
I. Entity Name
CERL
II. Description
It is the traffic generated during the call connections. The measurement begins from the
moment the phone rings to that the call is released.
III. Measurement Point
It is measured from the moment the ACM or DTAP Alerting message is received from
the destination MSC to that the REL message is received. The final result is indicated in
Erlang.
The callee may be in the local MSC or in another one. If the callee is in another office,
see point B in the following figure. If the callee is a local MS, see point E in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-170
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
D
DTAP ALERTING
IAM
ANM/ANC/ANN
C
A
B
E
F
DTAP SETUP
XXX
Incoming IAM or local SETUP
Incoming IAM or local SETUP

IV. Formula
None
8.13.13 Answered Traffic
I. Entity Name
RERL
II. Description
It is the traffic generated when the callees answer the calls. The measurement begins
from the moment the call is answered to that the call is released.
III. Measurement Point
It is measured from the moment the Answer signal or CONNECT ACK message is
received to that the REL message is received. The final result is indicated in Erlang.
The callee may be in the local MSC or in another one. If the callee is in another office,
see point C in the following figure. If the callee is a local MS, see point F in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-171
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
D
DTAP ALERTING
IAM
ANM/ANC/ANN
C
A
B
E
F
DTAP SETUP
XXX
Incoming IAM or local SETUP
Incoming IAM or local SETUP

IV. Formula
None
8.13.14 Call Completion Rate
I. Entity Name
CNTR
II. Description
Call completion rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
CNTR = CNT/PEGS
8.13.15 Answer Rate
I. Entity Name
ANSR
II. Description
Answer rate = Count of answered calls/Count of call attempts
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-172
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ANSR = ANS/PEGS
8.13.16 Count of MS Unavailable
I. Entity Name
CEUR
II. Description
It is the count of failed incoming call connections due to the paging failures.
III. Measurement Point
It is measured when the MSC does not receive the Paging Response message after
sending the Paging message to the RNC or BSC of the mobile callee in an incoming
call. See point A in the following figure.
RNC/BSC MSC Server
DTAP PAGING_RSP
XXX
DTAP PAGING
Mobile subscriber
unreachable
A
Incoming IAM or local SETUP

IV. Formula
None
8.13.17 Count of Failed Call Attempts Due to Inter-Trunk Failure
I. Entity Name
CFITB
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-173
II. Description
It is the count of failed calls due to all outgoing (bidirectional) trunks busy. And the call
connection type is the selected type. That is, the software invokes the database to
select an outgoing (bidirectional) trunk, but it fails. And the call connection type is the
selected type.
III. Measurement Point
It is measured when the MSC software fails to choose an outgoing (bidirectional) trunk
circuit. See point A in the following figure.
MSC Server MSC Server
IAM
A
XXX
Incoming IAM or local SETUP
Outgoing trunk
overflow

IV. Formula
None
8.13.18 Count of Failed Call Attempts Due to Inter-Trunk Failure
I. Entity Name
CFBTB
II. Description
It is the count of failed calls due to terrestrial channels unavailable. In an incoming call,
if the MSC fails to seize the terrestrial channels of the BSS before sending the
ASSIGNMENT REQUEST message to this BSS, the call connection fails.
III. Measurement Point
Before sending the ASSIGNMENT REQUEST message to this BSS in an incoming call,
if the MSC fails to seize the terrestrial channels of the BSS which the MS belongs to,
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-174
the measurement begins. It is measured only when the MS accesses from the interface
A. See point A in the following figure.
BSC MSC Server
DTAP ALERTING
XXX
DTAP SETUP
BSS trunk busy
A
Incoming IAM or local SETUP

IV. Formula
None
8.13.19 Count of Failed Call Attempts Due to Peer Office Congestion
I. Entity Name
CFPOB
II. Description
After the MSC sends the IAM or IAI to the peer office according to the routing
information in an outgoing call, the peer office or the terminating office returns an
unexpected backward message (excluding callee busy, invalid address) to indicate that
the call cannot be connected. This entity is the count of call connection failures in such
situation.
III. Measurement Point
It is measured in one of the following cases.
After sending the IAM, the MSC releases the call due to no response from the peer
office in a valid period.
The callee line is faulty.
The call connection fails.
The circuit group of the peer office is congested.
The sending of the dedicated signal tone fails.
The peer office is congested.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-175
See point A in the following figure.
MSC Server MSC Server
IAM
A
XXX
REL
ACM
Incoming IAM or local SETUP

IV. Formula
None
8.13.20 Count of Mobile Callee Determined Busy
I. Entity Name
CDBT
II. Description
It is the count of calls rejected because callees are busy.
III. Measurement Point
It is measured when the MSC receives the REL or DTAP Disconnect message from the
terminating office or callee. The value of the message is USER BUSY.
The call may be an incoming call or an outgoing one from the local MSC If the callee is
in another office, see point A in the following figure. If the callee is a local MS, see point
B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-176
MSC Server MSC Server
ACM
RNC/BSC
B
DTAP ALERTING
IAM
DTAP PAGING_RSP
A
XXX
DTAP SETUP
REL(CV_ST_BUSY/CV_SL_BUSY/CV_BUSY)
DTAP DISCONNECT(CV_BUSY)
DTAP ALERTING / ACM
ANM/ANC
DTAP CONNECT
DTAP ALERTING / ACM
Incoming IAM or local SETUP
Incoming IAM or local SETUP

IV. Formula
None
8.14 Intra-Office Traffic
8.14.1 Overview of MS_OFFICE_INT_MTM_TRAF
The names and meanings are listed in the following table.
Name Description
CA7 Count of call attempts
ABR7 Count of releases before ringing
TAF7 Count of terminal application failures
CRU7 Count of common resource application failures
CB7 Count of callee busy
MBTO7 Count of mobile callee trunk resource overflow
MAF7 Count of mobile callee traffic channel allocations failures
MNR7 Count of MS unavailable
ALT7 Count of connected calls
AAR7 Count of releases before the pickup
RNA7 Count of long time no reply
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-177
Name Description
MDB7 Count of mobile callee determined busy
ANS7 Count of answered calls
SU7 Seizure traffic
ALTU7 Connected traffic
ANSU7 Answered traffic
ALTR7 Call completion rate
ANSR7 Answer rate

8.14.2 Count of Call Attempts
I. Entity Name
CA7
II. Description
It is the count of call attempts initiated by the RNS and found to be intra-office ones
through DN analysis.
III. Measurement Point
After receiving the DTAP Setup message from the mobile caller, the MSC obtains
routing information from the HLR. After defining the call is an incoming one according to
the mobile station roaming number (MSRN), the MSC begins the measurement. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-178
RNC/BSC MSC Server
DTAP ALERTING
DTAP SETUP
A
RNC/BSC
DTAP SETUP
DTAP ALERTING
B
DTAP CONNECT
DTAP CONNECT
C

IV. Formula
None
8.14.3 Count of Releases Before Ringing
I. Entity Name
ABR7
II. Description
It is the count of active releases by the local mobile callers before calls are connected.
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from a mobile
caller before the call is connected. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-179
RNC/BSC MSC Server
DTAP ALERTING
A
RNC/BSC
DTAP SETUP
DTAP DISCONNECT
DTAP RELEASE

IV. Formula
None
8.14.4 Count of Terminal Application Failures
I. Entity Name
TAF7
II. Description
It is the count of call failures caused by Prepare Bearer failures on the MGW.
III. Measurement Point
It is measured when the MSC receives the Prepare Bearer Rsp message from the
MGW. The message contains failure information. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-180
RNC/BSC MSC Server
DTAP ALERTING
A
RNC/BSC
DTAP SETUP
DTAP DISCONNECT
DTAP DISCONNECT

IV. Formula
None
8.14.5 Count of Common Resource Application Failures
I. Entity Name
CRU7
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, DTR, bill pool, control table, and announcement resources.
III. Measurement Point
It is measured when the MSC fails to apply and use internal common resources. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-181
RNC/BSC MSC Server
DTAP ALERTING
A
RNC/BSC
DTAP SETUP
DTAP DISCONNECT
DTAP DISCONNECT

IV. Formula
None
8.14.6 Count of Callee Busy
I. Entity Name
CB7
II. Description
It is the count of call connections failed because mobile callees are busy in intra-office
calls.
III. Measurement Point
After getting the MSRN from the HLR, the MSC sends the message send info for
incoming/outgoing call setup to the VLR. The VLR returns a message to indicate that
the callee (no CF service) is busy, and then the MSC begins the measurement. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-182
RNC/BSC MSC Server
A
RNC/BSC
DTAP SETUP
DTAP SETUP
The MSC obtains the MSRN, and
the VLR returns a message
indicating callee busy.

IV. Formula
None
8.14.7 Count of Mobile Callee Trunk Resource Overflow
I. Entity Name
MBTO7
II. Description
It is the count of failed incoming calls due to the trunk resources unavailability on the
lu_CS interface.
III. Measurement Point
It is measured when the MSC queries the idle circuits before the allocation. In WCDMA
mode, the RNC establishes the AAL2, so there is no overflow measurement. See point
A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-183
BSC MSC Server
A
RNC/BSC
DTAP SETUP
DTAP SETUP
A interface circuits
allocation failure
DTAP ALERTING

IV. Formula
None
8.14.8 Count of Mobile Callee Traffic Channel allocations Failures
I. Entity Name
MAF7
II. Description
It is the count of failed call attempts caused by unsuccessful voice channel allocations
for the mobile callees in the incoming calls.
III. Measurement Point
It is measured when the MS receives the RAB ASSIGNMENT RESP message from the
RNC of the mobile callee, or receives the BSSMAP ASSIGN FAILURE from the BSC of
the mobile callee. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-184
RNC/BSC MSC Server
A
RNC/BSC
DTAP SETUP
DTAP SETUP
Called traffic channels
allocation failure
DTAP ALERTING

IV. Formula
None
8.14.9 Count of MS Unavailable
I. Entity Name
MNR7
II. Description
It is the count of failed incoming call connections due to paging failures.
III. Measurement Point
It is measured when the MSC does not receive the Paging Response message after
sending the Paging message to the RNC or BSC of the mobile callee in an incoming
call. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-185
RNC/BSC MSC Server
A
RNC/BSC
DTAP SETUP
DTAP PAGING
DTAP PAGING_RSP
Mobile subscriber
unreachable

IV. Formula
None
8.14.10 Count of Connected Calls
I. Entity Name
ALT7
II. Description
It is the count of DTAP Alerting messages sent to mobile callers in the intra-office calls.
III. Measurement Point
It is measured when the MSC sends the DTAP Alerting message to the local mobile
caller after receiving the DTAP Alerting message from the mobile callee. See point B in
the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-186
RNC/BSC MSC Server
DTAP ALERTING
DTAP SETUP
A
RNC/BSC
DTAP SETUP
DTAP ALERTING
B
DTAP CONNECT
DTAP CONNECT
C

IV. Formula
None
8.14.11 Count of Releases Before the Pickup
I. Entity Name
AAR7
II. Description
It is the count of active releases by mobile callers before the mobile callees pickup the
phones.
III. Measurement Point
It is measured when the mobile caller releases the call after receiving the DTAP Alerting
message but before the DTAP Connect message. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-187
RNC/BSC MSC Server
DTAP ALERTING
DTAP SETUP
RNC/BSC
DTAP SETUP
DTAP ALERTING
A
DTAP CONNECT
DTAP DISCONNECT
DTAP RELEASE

IV. Formula
None
8.14.12 Count of Long Time No Reply
I. Entity Name
RNA7
II. Description
It is the count of calls that are released because the callees do not answer till timeout.
III. Measurement Point
It is measured when the MSC releases the call due to no DTAP Connect message
received from the callee in a valid period after the DTAP Alerting message. See point A
in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-188
RNC/BSC MSC Server
DTAP ALERTING
DTAP SETUP
RNC/BSC
DTAP SETUP
DTAP ALERTING
A
DTAP CONNECT
DTAP DISCONNECT
DTAP RELEASE
Long time no reply

IV. Formula
None
8.14.13 Count of Mobile Callee Determined Busy
I. Entity Name
MDB7
II. Description
It is the count of incoming calls directly rejected by the mobile callees after the ringing.
III. Measurement Point
It is measured when the MSC receives the DTAP Disconnect message from the callee
after the ringing. The value of the message is CV_USER_BUSY or CV_BUSY. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-189
RNC/BSC MSC Server
DTAP ALERTING
DTAP SETUP
RNC/BSC
DTAP SETUP
DTAP ALERTING
A
DTAP CONNECT
DTAP DISCONNECT(CV_BUSY/
CV_USR_BUSY)
DTAP RELEASE

IV. Formula
None
8.14.14 Count of Answered Calls
I. Entity Name
ANS7
II. Description
It is the count of mobile incoming calls answered by the mobile callees.
III. Measurement Point
When receiving the DTAP Connect message from the mobile callee, the MSC sends
the DTAP Connect message to the mobile caller. After receiving the DTAP Connect
ACK message from the mobile caller, the MSC begins the measurement. See point C in
the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-190
RNC/BSC MSC Server
DTAP ALERTING
DTAP SETUP
A
RNC/BSC
DTAP SETUP
DTAP ALERTING
B
DTAP CONNECT
DTAP CONNECT
C

IV. Formula
None
8.14.15 Seizure Traffic
I. Entity Name
SU7
II. Description
It is the traffic generated during the intra-office call attempts.
III. Measurement Point
It measures the interval between relevant messages in a measurement period. For
WCDMA system, the MSC begins the measurement from the moment the message
MAP_SEND_ROUTING_INFORMATION is received to that the message IU RELEASE
COMMAND is sent. For GSM system, the MSC begins the measurement from the
moment the message MAP_SEND_ROUTING_INFORMATION is received to that the
message CLEAR COMMAND is sent. The final result is indicated in Erlang.
The release of the call is the measurement point. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-191
RNC/BSC MSC Server
A
RNC/BSC
DTAP SETUP
DTAP DISCONNECT
DTAP DISCONNECT

IV. Formula
None
8.14.16 Connected Traffic
I. Entity Name
ALTU7
II. Description
It is the traffic generated when intra-office calls are in the connected status.
III. Measurement Point
It measures the interval between relevant messages in a measurement period.
For WCDMA system, the MSC begins the measurement from the moment the
message DTAP Alerting is received to that the message IU RELEASE
COMMAND is sent.
For GSM system, the MSC begins the measurement from the moment the
message DTAP Alerting is received to that the message CLEAR COMMAND is
sent. The final result is indicated in Erlang.
The release of the call is the measurement point. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-192
RNC/BSC MSC Server
A
RNC/BSC
DTAP SETUP
DTAP DISCONNECT
DTAP DISCONNECT

IV. Formula
None
8.14.17 Answered Traffic
I. Entity Name
ANSU7
II. Description
It is the traffic generated when intra-office calls are in the answered status.
III. Measurement Point
It measures the interval between relevant messages in a measurement period.
For WCDMA system, the MSC begins the measurement from the moment the
message CONNECT ACKNOWLEDGE is received to that the message IU
RELEASE COMMAND is sent.
For GSM system, the MSC begins the measurement from the moment the
message CONNECT ACKNOWLEDGE is received to that the message CLEAR
COMMAND is sent.
The final result is indicated in Erlang. The release of the call is the measurement point.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-193
RNC/BSC MSC Server
A
RNC/BSC
DTAP SETUP
DTAP DISCONNECT
DTAP DISCONNECT

IV. Formula
None
8.14.18 Call Completion Rate
I. Entity Name
ALTR7
II. Description
Call completion rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is a calculated value.
IV. Formula
ALTR7 = ALT7/CA7
8.14.19 Answer Rate
I. Entity Name
ANSR7
II. Description
Answer rate = Count of answered calls/Count of call attempts
III. Measurement Point
It is a calculated value.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-194
IV. Formula
ANSR7 = ANS7/CA7
8.15 Call Forwarding Traffic
8.15.1 Overview of MS_FORWARD_TRAF
The names and meanings are listed in the following table.
Name Description
FORCAM Count of call forwarding attempts
FORCCN Count of forwarded calls
FORCAN Count of answered forwarded calls
FORST Count of call forwarding seizure traffic
FORCT Count of call forwarding connected traffic
FORAT Call forwarding answered traffic

8.15.2 Count of Call Forwarding Attempts
I. Entity Name
FORCAM
II. Description
It is the count of analyzed numbers in forwarding calls.
III. Measurement Point
It is measured when the MSC finishes analyzing the called number in a forwarding call.
If the callee is in another office, see point A in the following figure. If the callee is a local
MS, see point D in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-195
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
F
DTAP ALERTING
IAM
ANM/ANC
C
SETUP
A
B
D
E

IV. Formula
None
8.15.3 Count of Forwarded Calls
I. Entity Name
FORCCN
II. Description
It is the count of ACM received by the MSC in the forwarding call connections.
III. Measurement Point
It is measured when the MSC receives the ACM from the forwarded party. If the callee
is in another office, see point B in the following figure. If the callee is a local MS, see
point E in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-196
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
F
DTAP ALERTING
IAM
ANM/ANC
C
SETUP
A
B
D
E

IV. Formula
None
8.15.4 Count of Answered Forwarded Calls
I. Entity Name
FORCAN
II. Description
It is the count of answered forwarding calls.
III. Measurement Point
In an outgoing call, it is measured when the MSC receives the ANC or ANN message
from the forwarded party. In an incoming call, if the call is originated from the local MSC,
it is measured when the MSC receives the DTAP Connect message from the forwarded
party.
If the callee is in another office, see point C in the following figure. If the callee is a local
MS, see point F in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-197
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
F
DTAP ALERTING
IAM
ANM/ANC
C
SETUP
A
B
D
E

IV. Formula
None
8.15.5 Count of Call Forwarding Seizure Traffic
I. Entity Name
FORST
II. Description
It is the traffic generated during the forwarding call attempts.
III. Measurement Point
It is measured from the moment the call forwarding begins to that the REL message is
received. The final result is indicated in Erlang (ITU-T Rec. Q.722).
If the callee is in another office, see point A in the following figure. If the callee is a local
MS, see point D in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-198
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
F
DTAP ALERTING
IAM
ANM/ANC
C
SETUP
A
B
D
E

IV. Formula
None
8.15.6 Count of Call Forwarding Connected Traffic
I. Entity Name
FORCT
II. Description
It is the traffic generated when forwarding calls are in the connected status.
III. Measurement Point
It is measured from the moment the ACM or DTAP Alerting message is received to that
the REL message is received. The final result is indicated in Erlang (ITU-T Rec. Q.722).
If the callee is in another office, see point B in the following figure. If the callee is a local
MS, see point E in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-199
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
F
DTAP ALERTING
IAM
ANM/ANC
C
SETUP
A
B
D
E

IV. Formula
None
8.15.7 Call Forwarding Answered Traffic
I. Entity Name
FORAT
II. Description
It is the traffic generated when forwarded calls are in the answered status.
III. Measurement Point
It is measured from the moment the ANM or ANC or DTAP Connect message is
received to that the REL message is received. The final result is indicated in Erlang
(ITU-T Rec. Q.722).
If the callee is in another office, see point C in the following figure. If the callee is a local
MS, see point F in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-200
MSC Server MSC Server
ACM
RNC/BSC
DTAP CONNECT
F
DTAP ALERTING
IAM
ANM/ANC
C
SETUP
A
B
D
E

IV. Formula
None
8.16 Forwarded Subscriber Count
8.16.1 Overview of MS_FORWARD_USER
The name and meaning are listed in the following table.
Name Description
FORUN Count of subscribers forwarded to destination

8.16.2 Count of Subscribers Forwarded to Destination
I. Entity Name
FORUN
II. Description
It is the count of subscribers moved into the local area.
III. Measurement Point
It is measured when the subscriber data is inserted or modified.
1) The location update concerns two measurement points (B and C in the following
figure). The detailed procedures of inter-office location update are as follows.
The HLR sends CANCEL_LOCATION message to the previous VLR (PVLR).
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-201
The PVLR deletes the subscriber who has moved into another location area.
The PVLR checks the office of the forwarded-to number in the service subscription
information and updates the subscriber data.
See point B.
The HLR sends the INSERT_SUBSCRIBER_DATA message to the VLR.
The VLR checks the destination of the forwarded-to number in the service
subscription information and updates the subscriber data.
See point C.
MAP-UPDATE-LOCATION-
AREA
MAP-UPDATE-LOCATION
MAP-VDB-INSERT-SUBSCRIVER-DATA
MAP-VDB-INSERT-SUBSCRIVER-DATA-ACK
MAP-PROVIDE-IMSI
MAP-PROVIDE-IMSI-ACK
MAP-CANCEL-LOCTION
MAP-CANCEL-LOCTION-ACK
MSC VLR PVLR HLR
MAP-UPDATE-LOCATION-ACK
MAP-UPDATE-LOCATION-
AREA-ACK
B
C
D
A

2) The subscriber data operation of the HLR concerns two measurement points (A
and B in the following figure). The detailed procedures are as follows.
For removing the subscriber, the HLR sends the CANCEL_LOCATION message
to the current VLR.
The VLR deletes the subscriber moved into another location area.
The VLR checks the destination of the forwarded number in the service
subscription information of the subscriber data and updates the subscriber data.
See point A.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-202
MAP-CANCEL-LOCTION
MAP-CANCEL-LOCTION-ACK
VLR HLR OMC
Delete subscriber
Subscriber deleted
A

For modifying the supplementary service data of the subscriber, the HLR sends a
MAP-INSERT-SUB-DATA or MAP-DELETE-SUB-DATA message to the current
VLR.
The VLR updates the subscriber data of supplementary services.
The VLR checks the destination of the forwarded number in the service
subscription information of the subscriber data and updates the subscriber data.
See point B in the following figure.
MAP-INSERT-SUB-DATA or
MAP-DELETE-SUB-DATA
MAP-INSERT-SUB-DATA-ACK or
MAP-DELETE-SUB-DATA-ACK
VLR HLR OMC
Modify user data
Subscriber data
modified
B

3) The procedures of functionalizing the supplementary services concerns one
measurement point. See point A in the following figure.
When the MS initiates a supplementary service data operation, the HLR initiates a
flow of inserting subscriber data to the current VLR.
The VLR compares the supplementary service subscription information in local
VLR with that in the message.
If it requires to add or remove the number, the VLR checks the destination of the
forwarded number in the service subscription information of the subscriber data
and updates the subscriber data.
See point A.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-203
MAP-REG / ERASE / ACT /
DEA-SS
MAP-REG / ERASE / ACT /
DEA-SS-ACK
MSC VLR HLR
A
MAP-REG / ERASE / ACT /
DEA-SS
MAP-REG / ERASE / ACT /
DEA-SS-ACK
MAP-INSERT-
SUBSCRIBER-DATA

4) The internal VLR periodical subscriber management concerns one measurement
point. See point B in the following figure.
if there is no message interaction between a subscriber and the VLR during a period
specified in the VLR configuration table, the VLR directly removes the subscriber data
and notifies the HLR. At the same time, the VLR checks the destination of the
forwarded number in the service subscription information of the subscriber data and
updates the subscriber data.
MAP-PURGY-MS
MSC HLR VLR
MAP-PURGY-MS
MAP-PURGY-MS-ACK
MAP-PURGY-MS-ACK
B

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-204
8.17 Failure Causes of the Office
8.17.1 Overview of MS_FAULT_REASON_TRAF
The names and meanings are listed in the following table.
Name Description
NSSETCFT Count of supplementary service setting conflict
NSSETOK Count of supplementary service setting successes
NSSETFL Count of supplementary service setting failures
NSCANOK Count of supplementary service deregistration successes
NSCANFL Count of supplementary service deregistration failures
NSTSTOK Count of supplementary service authentication successes
NSTSTFL Count of supplementary service authentication failures
NSUSOK Count of supplementary service application successes
NSUSFL Count of supplementary service application failures
MCTOK Count of successes in probing malicious calls
MCTFL Count of failures in probing malicious calls
SEC Count of MSC congestions
LTNDG Count of long time no dialing
LTNANS Count of long time no reply
SYSFL Count of temporary failures
RTSTOK Count of self-test successes
LTNINF Count of long time no messages
LTNRG Count of long time no ringing
LTNRLS Count of long time no release
INBSIG Count of inband signals
COCFL Count of continuity check failures
EXREATP Count of exceeding max. call attempts
BRGABN Count of releases before ringing
ARGABN Count of releases before the pickup
BAR Count of call restrictions
SEFL Count of MSC failures
SEFL1 Count of toll calls to busy callee
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-205
Name Description
SEFL2 Count of local calls to busy callee
REPMCG Count of peer office congestion
CLFL Count of call failures
DSEIZ Count of contentions
INVCD Count of invalid numbers
NMNBAR Count of network management barring
CPUOL Count of CPU congestions and overload
NCR Count of no CR resources
NCCB Count of no CCB resources
IFCR Count of incoming office CF barring
DIALTO Count of dialing time out
SIGER Count of signaling failures
BWLBAR Count of black list calls barred
BWLBAR1 Count of caller number identification failures
NACFBS Count of no A interface resource for a bearer service
NAC Count of no A interface resources
ICUGS Count of CUG service incompatible
UCUG Count of unknown CUG
NSCUG Count of CUG unselected
BOCUG Count of CUG outgoing calls barred
BICUG Count of CUG incoming calls barred
CUGSSI Count of CUG supplementary service failures
ICUGD Count of CUG destination incompatible
CL Count of released calls
HOC Count of Switchover successes
HOF Count of Switchover failures
TECLT Count of call restriction duration timeout
TF Count of termination resource application failures
CDNE Count of callee number not exist (excluding fixed-line numbers)
NAFCD Count of mobile callee no reply
CDBAIC Count of mobile callee incoming call restricted
CRBOAC Count of call out restrictions
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-206
Name Description
CDUR Count of callee unreachable
NACP Count of calling local subscriber without area code
CDB Count of mobile callee busy
CDPO Count of mobile callee power-off
SNA Count of required function not applied
DZ Count of toll calls without 0
CFV Count of CF conflict
ESRI Count of failures in HLR obtaining route information
ODBAOC Count of all outgoing calls barred by operators
ODBOIC Count of all outgoing international calls barred by operators
UBOICE Count of all outgoing international calls barred by subscriber
UBOICENH Count of BOIC-exHC barred by subscribers
ODBOICE Count of BOIC-exHC barred by operators
ODBAIC Count of all incoming calls barred by operators
ODBEC Count of operators barring entertainment console
ODBMC Count of operators barring announcement console
SROP Count of subscriber roaming out
ODBT Count of all national toll calls barred by operators
UN Count of cause unknown failures
UALCCD Count of unallocated numbers
NRUTOSI Count of no route to specified transit network
NRUTOTE Count of no route to destination
SPRVTONE Count of sending private tone
ERLNGPFX Count of wrongly dialed numbers of toll call prefix
RUUAPT Count of unacceptable paths
CALLEST Count of calls connected and delivered on established route
ODB Count of calls barred by operators
RFREUSE Count of circuits reserved for reusing
NORCLR Count of normally cleared calls
UDB Count of callee determined busy
NRSP Count of no reply
NACK Count of no response
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-207
Name Description
AS Count of callee absent
REJ Count of calls rejected
CDCHD Count of number changed
NFC Count of no idle circuits
RABPE Count of rab pre-empted
TEER Count of callee failures
INVCDFMT Count of invalid number formats
FACREJ Count of facilities rejected
RSPSE Count of responses to STATUS ENQUIRY
NOR Count of normally cleared calls
NCIR Count of unavailable circuits
NETER Count of network failures
TMPER Count of contemporary failures
EPMCG Count of MSC failures
AIL Count of accessed messages discarded
NRUCIR Count of unavailable routes
PCALLBLK Count of unavailable paths
NRSC Count of unavailable resources
NSSQUA Count of no suitable service quality
FACNPV Counts of facility applied not preserved before
CUGBC Count of CUG outgoing call restriction
CUGUALW Count of CUG incoming call restriction
BCUNP Count of bearer capability authorized
NBC Count of no available bearer capability
NSSOOP Count of no suitable service or optional project
BCNLO Count of bearer capability not implemented
RTNLO Count of path type not implemented
AOCRF Count of AOC service request failures
ACMEG Count of ACM equaling or greater than ACMmax
FACNLO Count of requested equipment not implemented
LTDDIBC Count of restricted bearer capability
IWFRU Count of IWF resource unavailable
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-208
Name Description
SOPNLO Count of service or optional project not implemented
INVCR Count of invalid call reference values
RUNEXT Count of identified route not exist
CLDNOCUG Count of callee not CUG subscriber
TEUCPT Count of incompatible terminals
NECUG Count of CUGs not exist
INVTNL Count of invalid transit network selection
INVMSG Count of invalid messages
MSGNOEXT Count of Non-Existent or Not Implemented message types
IENOEXT Count of Non-Existent or Not Implemented message units
TOUT Count of timeout recoveries
PARANOEXT Count of Non-Existent or Not Implemented parameters
UNRECPARA Count of messages carrying unidentified parameters
PROERR Count of protocol errors
INTWORK Count of interworking

8.17.2 Count of Supplementary Service Setting Conflict
I. Entity Name
NSSETCFT
II. Description
It is the count of setting failures of supplementary services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.3 Count of Supplementary Service Setting Successes
I. Entity Name
NSSETOK
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-209
II. Description
It is the count of successful settings of the supplementary services
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.4 Count of Supplementary Service Setting Failures
I. Entity Name
NSSETFL
II. Description
It is the count of setting failures of supplementary services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.5 Count of Supplementary Service Deregistration Successes
I. Entity Name
NSCANOK
II. Description
It is the count of successful deregistration of supplementary services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.6 Count of Supplementary Service Deregistration Failures
I. Entity Name
NSCANFL
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-210
II. Description
It is the count of deregistration failures of supplementary services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.7 Count of Supplementary Service Authentication Successes
I. Entity Name
NSTSTOK
II. Description
It is the count of successful authentication of supplementary services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.8 Count of Supplementary Service Authentication Failures
I. Entity Name
NSTSTFL
II. Description
It is the count of authentication failures of supplementary services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.9 Count of Supplementary Service Application Successes
I. Entity Name
NSUSOK
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-211
II. Description
It is the count of successful application of supplementary services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.10 Count of Supplementary Service Application Failures
I. Entity Name
NSUSFL
II. Description
It is the count of application failures of supplementary services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.11 Count of Successes in Probing Malicious Calls
I. Entity Name
MCTOK
II. Description
It is the count of successes in probing malicious calls.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.12 Count of Failures in Probing Malicious Calls
I. Entity Name
MCTFL
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-212
II. Description
It is the count of failures in probing malicious calls.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.13 Count of MSC Congestions
I. Entity Name
SEC
II. Description
It is the count of internal MSC congestions.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.14 Count of Long Time No Dialing
I. Entity Name
LTNDG
II. Description
It is the count of long time no dialing after the callers hook off.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.15 Count of Long Time No Reply
I. Entity Name
LTNANS
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-213
II. Description
It is the count of calls that are released because the callees do not answer till timeout.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.16 Count of Temporary Failures
I. Entity Name
SYSFL
II. Description
It is the count of call releases because the system performance declines due to
message losses, internal errors, or message combination failures.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.17 Count of Self-Test Successes
I. Entity Name
RTSTOK
II. Description
It is the count of self-test successes.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-214
8.17.18 Count of Long Time No Messages
I. Entity Name
LTNINF
II. Description
It is the count that the subscribers do not receive the messages in a specified period.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.19 Count of Long Time No Ringing
I. Entity Name
LTNRG
II. Description
It is the count of connection failures due to timeout when the caller does not receive the
message DTAP Alerting after receiving the message PAGING ACK from the callee.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.20 Count of Long Time No Release
I. Entity Name
LTNRLS
II. Description
It is the count of calls disconnected in specified periods after the DISCONNECT
messages are received.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-215
IV. Formula
None
8.17.21 Count of Inband Signals
I. Entity Name
INBSIG
II. Description
It is the count of inband signals.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.22 Count of Continuity Check Failures
I. Entity Name
COCFL
II. Description
It is the count of continuity check failures in the peer office.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.23 Count of Exceeding Max. Call Attempts
I. Entity Name
EXREATP
II. Description
It is the count of call attempts that exceed the maximum number in the call connections
due to the contention.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-216
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.24 Count of Releases Before Ringing
I. Entity Name
BRGABN
II. Description
It is the count of mobile caller releases before the callees' phones ring.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.25 Count of Releases Before the Pickup
I. Entity Name
ARGABN
II. Description
It is the count of active releases by the callers before the pickup.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.26 Count of Call Restrictions
I. Entity Name
BAR
II. Description
It is the count of calls barred due to subscriber service restrictions.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-217
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.27 Count of MSC Failures
I. Entity Name
SEFL
II. Description
It is the count of MSC failures in processing the IN services and iPath.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.28 Count of Toll Calls to Busy Callee
I. Entity Name
SEFL1
II. Description
It is the count of messages indicating the callees are busy in fixed toll calls.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.29 Count of Local Calls to Busy Callee
I. Entity Name
SEFL2
II. Description
It is the count of messages indicating callees busy in local fixed calls.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-218
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.30 Count of Peer Office Congestion
I. Entity Name
REPMCG
II. Description
It is the count of calls failed due to congestions in the peer office.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.31 Count of Call Failures
I. Entity Name
CLFL
II. Description
It is caused by the following reasons:
The peer office is congested and the MSC cannot obtain the addressing message
after receiving the SETUP message.
The peer office DSP is unavailable and the TUP releases the call due to timeout.
The called number is less than that requested when the MSC receives the IAM.
The MSC receives the RLG message abnormally.
The channel is blocked due to TUP circuit busy.
The circuit group is blocked.
The internal timer is timeout when the TUP is in the ringing state.
The MSC fails to receive the GSM message.
The TUP fails to receive the SETUP message.
The CFL message is received.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-219
IV. Formula
None
8.17.32 Count of Contentions
I. Entity Name
DSEIZ
II. Description
It is the count of trunk busy due to contentions.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.33 Count of Invalid Numbers
I. Entity Name
INVCD
II. Description
It is the count of invalid numbers due to called number analysis failures.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.34 Count of Network Management Barring
I. Entity Name
NMNBAR
II. Description
It is the count of calls barred by the NMS.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-220
IV. Formula
None
8.17.35 Count of CPU Congestions and Overload
I. Entity Name
CPUOL
II. Description
It is the count of CPU congestions and overload.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.36 Count of No CR Resources
I. Entity Name
NCR
II. Description
It is the count of insufficient CR resources which are used by the subscriber side (CCB
at network side) when originating or terminating calls.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.37 Count of No CCB Resources
I. Entity Name
NCCB
II. Description
It is the count of insufficient CCB resources which are used by the network side when
originating or terminating calls.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-221
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.38 Count of Incoming Office CF Barring
I. Entity Name
IFCR
II. Description
It is the count of forwarding calls barred by the peer office.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.39 Count of Dialing Time Out
I. Entity Name
DIALTO
II. Description
It is the count of timeout in dialing.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.40 Count of Signaling Failures
I. Entity Name
SIGER
II. Description
It is the count of signaling cooperation failures between SS7 and SS1.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-222
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.41 Count of Black List Calls Barred
I. Entity Name
BWLBAR
II. Description
It is the count of calls barred because the callers or callees are in the black list.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.42 Count of Caller Number Identification Failures
I. Entity Name
BWLBAR1
II. Description
It is the count of failures in identifying the caller numbers.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.43 Count of No A Interface Resource for A Bearer Service
I. Entity Name
NACFBS
II. Description
It is the count of no A interface resources for bearing the services.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-223
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.44 Count of No A Interface Resources
I. Entity Name
NAC
II. Description
It is the count of no A interface circuits.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.45 Count of CUG Service Incompatible
I. Entity Name
ICUGS
II. Description
It is the count of supplementary service failures due to CUG service incompatible.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.46 Count of Unknown CUG
I. Entity Name
UCUG
II. Description
It is the count of supplementary service failures due to CUG unknown.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-224
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.47 Count of CUG Unselected
I. Entity Name
NSCUG
II. Description
It is the count of supplementary service failures due to CUG unselected.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.48 Count of CUG Outgoing Calls Barred
I. Entity Name
BOCUG
II. Description
It is the count of calls barred due to CUG outgoing restrictions.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.49 Count of CUG Incoming Calls Barred
I. Entity Name
BICUG
II. Description
It is the count of calls barred due to CUG incoming restrictions.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-225
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.50 Count of CUG Supplementary Service Failures
I. Entity Name
CUGSSI
II. Description
It is the count of supplementary service failures due to CUG supplementary service
failures.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.51 Count of CUG Destination Incompatible
I. Entity Name
ICUGD
II. Description
It is the count of supplementary service failures due to CUG destination incompatible.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.52 Count of Released Calls
I. Entity Name
CL
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-226
II. Description
It is the count of released calls.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.53 Count of Switchover Successes
I. Entity Name
HOC
II. Description
It is the count of successful switchovers.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.54 Count of Switchover Failures
I. Entity Name
HOF
II. Description
It is the count of switchover failures.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.55 Count of Call Restriction Duration Timeout
I. Entity Name
TECLT
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-227
II. Description
It is the count of calls released because the session durations exceed the threshold.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.56 Count of Termination Resource Application Failures
I. Entity Name
TF
II. Description
It is the count of application failures of the Termination resources.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.57 Count of Callee Number Not Exist (Excluding Fixed-Line Numbers)
I. Entity Name
CDNE
II. Description
It is the count of messages indicating the HLR has no information about the callees
number.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-228
8.17.58 Count of Mobile Callee No Reply
I. Entity Name
NAFCD
II. Description
It is the count of mobile callees no reply after ringing.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.59 Count of Mobile Callee Incoming Call Restricted
I. Entity Name
CDBAIC
II. Description
It is the count of calls failed because the mobile callees have set incoming call
restrictions.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.60 Count of Call out Restrictions
I. Entity Name
CRBOAC
II. Description
It is the count of calls failed because the mobile callers have set outgoing call
restrictions.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-229
IV. Formula
None
8.17.61 Count of Callee Unreachable
I. Entity Name
CDUR
II. Description
It is the count of calls of which the mobile callees are unreachable, power-off, or
abnormal.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.62 Count of Calling Local Subscriber Without Area Code
I. Entity Name
NACP
II. Description
It is the count of callee numbers without area codes when the MSs make local fixed-line
calls.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.63 Count of Mobile Callee Busy
I. Entity Name
CDB
II. Description
It is the count of calls restricted because mobile callees are busy.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-230
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.64 Count of Mobile Callee Power-Off
I. Entity Name
CDPO
II. Description
It is the count of failed call connections (during called number analysis in MSC) due to
callees power-off.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.65 Count of Required Function Not Applied
I. Entity Name
SNA
II. Description
It is the count of required service functions that are not applied.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.66 Count of Toll Calls Without 0
I. Entity Name
DZ
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-231
II. Description
It is the count of unallocated numbers generated when the callers make non-local calls
without adding "0".
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.67 Count of CF Conflict
I. Entity Name
CFV
II. Description
It is the count of calls released due to CF conflicts resulted from the forwarding time
restriction for the same reason.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.68 Count of Failures in HLR Obtaining Route Information
I. Entity Name
ESRI
II. Description
It is the count of routing selection and protocol errors.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-232
8.17.69 Count of All Outgoing Calls Barred by Operators
I. Entity Name
ODBAOC
II. Description
It is the count of outgoing calls barred by operators.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.70 Count of All Outgoing International Calls Barred by Operators
I. Entity Name
ODBOIC
II. Description
It is the count of outgoing international calls barred by operators.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.71 Count of All Outgoing International Calls Barred by Subscribers
I. Entity Name
UBOICE
II. Description
It is the count of outgoing international calls barred by subscribers.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-233
8.17.72 Count of BOIC-exHC Barred by Subscribers
I. Entity Name
UBOICENH
II. Description
It is the count of outgoing international calls barred by subscribers except those
directed to the home PLMN country.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.73 Count of BOIC-exHC Barred by Operators
I. Entity Name
ODBOICE
II. Description
It is the count of outgoing international calls barred by operators except those directed
to the home PLMN country.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.74 Count of All Incoming Calls Barred by Operators
I. Entity Name
ODBAIC
II. Description
It is the count of all incoming calls barred by operators.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-234
IV. Formula
None
8.17.75 Count of Operators Barring Entertainment Console
I. Entity Name
ODBEC
II. Description
It is the count of messages indicating that the operators bar the entertainment
consoles.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.76 Count of Operators Barring Announcement Console
I. Entity Name
ODBMC
II. Description
It is the count of messages indicating that the operators bar the announcement
consoles.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.77 Count of Subscriber Roaming Out
I. Entity Name
SROP
II. Description
It is the count of calls failed because subscribers not in the service area.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-235
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.78 Count of All National Toll Calls Barred by Operators
I. Entity Name
ODBT
II. Description
It is the count of national toll calls barred by operators.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.79 Count of Cause Unknown Failures
I. Entity Name
UN
II. Description
It is the count of failed calls due to unknown causes.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.80 Count of Unallocated Numbers
I. Entity Name
UALCCD
II. Description
It is the count of unallocated numbers due to the following reasons:
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-236
The route selection source code or the route selection code is empty.
The bsn of the circuit in the table is empty.
The called number analysis fails according to the data configuration table.
The MAP fails to return the called number to the calling module.
The calling module fails to obtain the MSISDN or IMSI in the caller data.
The MSC receives the UNN message from the TUP of the callee side.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.81 Count of No Route to Specified Transit Network
I. Entity Name
NRUTOSI
II. Description
It is the count of calls that have no routes to the specified transit network due to the
following causes. The equipment receives an alternative calling request from the
specified but unknown transit network. The equipment cannot recognize this transit
network because the network does not exist or does not provide any service to the
equipment. The network determines whether to support this cause value.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.82 Count of No Route to Destination
I. Entity Name
NRUTOTE
II. Description
It is the count of calls that have no routes to the destinations due to terrestrial circuits
allocation failures and MM_CC_REL_IND from the bottom layer.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-237
IV. Formula
None
8.17.83 Count of Sending Private Tone
I. Entity Name
SPRVTONE
II. Description
It is the count of private tones sent due to peer office congestions.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.84 Count of Wrongly Dialed Numbers of Toll Call Prefix
I. Entity Name
ERLNGPFX
II. Description
It is the count of faulty prefixes of the called numbers.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.85 Count of Unacceptable Paths
I. Entity Name
RUUAPT
II. Description
It is the count of calls rejected due to unacceptable paths.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-238
IV. Formula
None
8.17.86 Count of Calls Connected and Delivered on Established Route
I. Entity Name
CALLEST
II. Description
It is the count of calls connected and delivered on the established paths.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.87 Count of Calls Barred by Operators
I. Entity Name
ODB
II. Description
It is the count of calls barred by operators.
III. Measurement Point
It is the count of calls barred by operators.
IV. Formula
None
8.17.88 Count of Circuits Reserved for Reusing
I. Entity Name
RFREUSE
II. Description
It is the count of circuits reserved for reusing.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-239
IV. Formula
None
8.17.89 Count of Normally cleared Calls
I. Entity Name
NORCLR
II. Description
It is the count of normally cleared calls.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.90 Count of Callee Determined Busy
I. Entity Name
UDB
II. Description
It is the count of calls failed because callees are busy.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.91 Count of No Reply
I. Entity Name
NRSP
II. Description
It is the count of calls not replied for a long time till timeout.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-240
IV. Formula
None
8.17.92 Count of No Response
I. Entity Name
NACK
II. Description
This cause value is used when there is no response from the callee in a specified
period or when the link indication responds that the call is connected.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.93 Count of Callee Absent
I. Entity Name
AS
II. Description
It is the count of calls of which the callees are absent.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.94 Count of Calls Rejected
I. Entity Name
REJ
II. Description
It is the count of rejected calls.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-241
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.95 Count of Number Changed
I. Entity Name
CDCHD
II. Description
It is the count of invalid numbers due to changes of called numbers.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.96 Count of No Idle Circuits
I. Entity Name
NFC
II. Description
It is the count of failed calls due to no idle circuits.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.97 Count of RAB Pre-Empted
I. Entity Name
RABPE
II. Description
It is the count of calls released due to RAB resources seizure conflicts.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-242
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.98 Count of Callee Failures
I. Entity Name
TEER
II. Description
It is the count of calls of which the callees are abnormal.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.99 Count of Invalid Number Formats
I. Entity Name
INVCDFMT
II. Description
It is the count of calls cannot reach the callees due to invalid called numbers format or
incomplete called numbers. This cause value is used in this case.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.100 Count of Facilities Rejected
I. Entity Name
FACREJ
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-243
II. Description
It is the count of facilities rejected.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.101 Count of Responses to STATUS ENQUIRY
I. Entity Name
RSPSE
II. Description
It is the count of responses to the STATUS_ENQUIRY messages.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.102 Count of Normally cleared Calls
I. Entity Name
NOR
II. Description
It is the count of normally cleared calls.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.103 Count of Unavailable Circuits
I. Entity Name
NCIR
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-244
II. Description
It is the count of unavailable circuits. The circuits may be unavailable in:
querying the TUP circuits.
allocating the territorial circuits after the switch.
allocating the territorial circuits.
indication empty of the internal HW networks.
receiving the CGC message.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.104 Count of Network Failures
I. Entity Name
NETER
II. Description
It is the count of CC internal processing failures.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.105 Count of Contemporary Failures
I. Entity Name
TMPER
II. Description
It is the count of internal failures.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-245
8.17.106 Count of MSC Failures
I. Entity Name
EPMCG
II. Description
It is the count of MSC failures. The equipment sends this cause value to indicate the
MSC is in the high traffic stage.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.107 Count of Accessed Messages Discarded
I. Entity Name
AIL
II. Description
It is the count of accessed messages discarded. This cause value indicates the
network cannot deliver the access information to the remote subscribers. That is,
subscriber-subscriber information, lower-layer compatibility, higher-layer compatibility,
or sub-address indicated in the diagnosis.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.108 Count of Unavailable Routes
I. Entity Name
NRUCIR
II. Description
It is the count of failures in querying or allocating trunk resources.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-246
IV. Formula
None
8.17.109 Count of Unavailable Paths
I. Entity Name
PCALLBLK
II. Description
It is the count of unavailable paths.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.110 Count of Unavailable Resources
I. Entity Name
NRSC
II. Description
It is the count of failures in allocating resources including the calling module control
table and paths.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.111 Count of No Suitable Service Quality
I. Entity Name
NSSQUA
II. Description
It is the count of calls with no suitable service qualities. This cause value reports the
service quality defined in the X.213 cannot be provided (for example, throughput and
transfer delay).
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-247
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.112 Counts of Facility Applied Not Preserved Before
I. Entity Name
FACNPV
II. Description
It is the count of services or optional projects not preserved before.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.113 Count of CUG Outgoing Call Restriction
I. Entity Name
CUGBC
II. Description
It is the count of calls barred due to CUG call-out restrictions.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.114 Count of CUG Incoming Call Restriction
I. Entity Name
CUGUALW
II. Description
It is the count of CUG incoming calls barred due to CUG call-in restrictions.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-248
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.115 Count of Bearer Capability Authorized
I. Entity Name
BCUNP
II. Description
It is the count of calls released due to no bearer services registered.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.116 Count of No Available Bearer Capability
I. Entity Name
NBC
II. Description
It is the count of messages indicating the MSC has no bearer resources, including the
trunk and software resources.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.117 Count of No Suitable Service or Optional Project
I. Entity Name
NSSOOP
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-249
II. Description
It is the count of no suitable services or optional projects.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.118 Count of Bearer Capability Not Implemented
I. Entity Name
BCNLO
II. Description
It is the count of calls released due to no implemented bearer services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.119 Count of Path Type Not Implemented
I. Entity Name
RTNLO
II. Description
It is the count of calls with the path type not implemented. In this case, the equipment
sends this cause value.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-250
8.17.120 Count of AOC Service Request Failures
I. Entity Name
AOCRF
II. Description
It is the count of AOC service request failures.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.121 Count of ACM Equaling or Greater Than ACM max
I. Entity Name
ACMEG
II. Description
It is the count of ACMs equaling or greater than the ACM max.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.122 Count of Requested Equipment Not Implemented
I. Entity Name
FACNLO
II. Description
It is the count of requested equipment not implemented.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-251
8.17.123 Count of Restricted Bearer Capability
I. Entity Name
LTDDIBC
II. Description
It is the count of calls released due to restricted bearer capability. The callers have
registered the non-restricted services, but the equipment sending the cause value only
supports the restricted services.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.124 Count of IWF Resource Unavailable
I. Entity Name
IWFRU
II. Description
It is the count of unavailable IWF resources.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.125 Count of Service or Optional Project Not Implemented
I. Entity Name
SOPNLO
II. Description
It is the count of services or optional projects not implemented.
III. Measurement Point
It is measured when the MSC releases the call.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-252
IV. Formula
None
8.17.126 Count of Invalid Call Reference Values
I. Entity Name
INVCR
II. Description
The equipment sends this cause value because it receives the message carrying the
calling reference value that is not used on the current subscriber-network interface.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.127 Count of Identified Route Not Exist
I. Entity Name
RUNEXT
II. Description
It is the count of identified routes that do not exist.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.128 Count of Callee not CUG Subscriber
I. Entity Name
CLDNOCUG
II. Description
It is the count of messages indicating the callees are not CUG subscribers.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-253
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.129 Count of Incompatible Terminals
I. Entity Name
TEUCPT
II. Description
It is the count of incompatible terminals. The caller bearer capability specifies the
non-voice service, but the callee does not support the ISUP interface or other interfaces
that support the data services. The TUP supports non-restricted services if the ACB
(access barred) is not received.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.130 Count of CUG Not Exist
I. Entity Name
NECUG
II. Description
It is the count of supplementary service failures due to the non-existence of CUGs.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.131 Count of Invalid Transit Network Selection
I. Entity Name
INVTNL
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-254
II. Description
The received transit network identifier is not the correct format as defined in the
Appendix C.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.132 Count of Invalid Messages
I. Entity Name
INVMSG
II. Description
It is the count of invalid messages.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.133 Count of Non-Existent or Not Implemented Message Types
I. Entity Name
MSGNOEXT
II. Description
It is the count of message types that do not exist or are not implemented.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-255
8.17.134 Count of Non-Existent or Not Implemented Message Units
I. Entity Name
IENOEXT
II. Description
It is the count of message units that do not exist or are not implemented.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.135 Count of Timeout Recoveries
I. Entity Name
TOUT
II. Description
It is the count of timeout recoveries of timers.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.136 Count of Non-Existent or Not Implemented Parameters
I. Entity Name
PARANOEXT
II. Description
It is the count of parameters that do not exist or are not implemented.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-256
8.17.137 Count of Messages Carrying Unidentified Parameters
I. Entity Name
UNRECPARA
II. Description
It is the count of messages carrying the unidentified parameters.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.138 Count of Protocol errors
I. Entity Name
PROERR
II. Description
It is the count of protocol errors.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
8.17.139 Count of Interworking
I. Entity Name
INTWORK
II. Description
It is the count of interworking.
III. Measurement Point
It is measured when the MSC releases the call.
IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-257
8.18 Incoming Traffic
8.18.1 Overview of MS_OFFICE_INC_TRAF
The names and meanings are listed in the following table.
Name Description
SEIZ Count of seizure
ANS Count of answered calls
PDIMP Count of incomplete numbers
INVADR Count of invalid addresses
SYSFLCL Count of failed calls due to internal failure
ALBLCL Count of call failures due to overload
FWCTLCL Count of call failures due to network management
SERL Seizure traffic
RERL Answered traffic
MNTCIR Count of circuits in maintenance
ANSR Answer rate
ALTN Count of connected calls
ALTT Connected traffic
ALTR Call completion rate
UPOT Count of callee power-off

8.18.2 Count of Seizure
I. Entity Name
SEIZ
II. Description
It is the count of seizure of incoming trunk circuits or BICC CIC.
III. Measurement Point
It is measured when a call seizes an incoming trunk circuit or BICC CIC.
It is measured when the ISUP receives the IAM. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-258
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
CCB ISUP(inc)
B
ANM
Connect
Connect Ack
ANM
Connect
Connect Ack
C
A

IV. Formula
None
8.18.3 Count of Answered Calls
I. Entity Name
ANS
II. Description
It is the count of calls answered, no matter whether the calls are in supplementary
services (CFU, CFB, or CFNR).
III. Measurement Point
It is measured when the Connect message is received.
It is measured when the ISUP receives the Connect message. See point C in the
following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-259
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
CCB ISUP(inc)
B
ANM
Connect
Connect Ack
ANM
Connect
Connect Ack
C
A

IV. Formula
None
8.18.4 Count of Incomplete Numbers
I. Entity Name
PDIMP
II. Description
The incoming (bidirectional) trunk cannot define whether the call is a terminating call or
tandem call due to incomplete number. It includes the following cases:
The trunk does not send number.
The number is discarded during the dialing.
The interval of dialing is timeout.
The incoming trunk releases the call.
III. Measurement Point
It is measured when the incoming trunk stops collecting the numbers due to abnormity.
1) Call failure due to incomplete number (case 1)
The cause value of the REL message may be one of the following.
CV_NORMAL
CV_NORMAL_CALL_CLEAR
CV_RELEASE_BEFORE_ANSWER
CV_RELEASE_BEFORE_RING
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-260
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
REL
CCB ISUP(inc)
A

2) Call failure due to incomplete number (case 2)
The cause value of the Release message may be one of the following.
CV_LONG_TIME_NO_DIALING
CV_PARTIAL_DIAL_TIMEOUT
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
REL
Release
Release
REL

3) Call failure due to incomplete number (case 3)
The cause value of the Release message may be one of the following.
CV_LONG_TIME_NO_DIALING
CV_PARTIAL_DIAL_TIMEOUT
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-261
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
ACM
Alerting
Alerting
ACM
REL
Release
Release
REL

IV. Formula
None
8.18.5 Count of Invalid Addresses
I. Entity Name
INVADR
II. Description
The numbers received by the incoming trunk are not consistent with the existing
destination address or the confirmed address numbers. The call is processed by
intercepting (sending signal tone, announcement, or operator speech). The numbers
include the invalid number and the number by which the callee cannot be found.
III. Measurement Point
It is measured when the complete number is wrong.
1) Invalid address (case 1)
The cause value of the Release message may be one of the following.
CV_NUMBER_CHANGED
CV_DIAL_NO_RESERED
CV_UNALOC_CODE
CV_INVALID_CODE_FORM
CV_INVALID_FORMAT_OR_ADDRESS_NOT_ENOUGH
CV_ERROR_INCLUDE_LONG_DISTANCE
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-262
CV_GSM_CLD_DN_NO_EXIST
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
REL
Release
Release
REL

2) Invalid address (case 2)
The cause value of the Release message may be one of the following.
CV_NUMBER_CHANGED
CV_DIAL_NO_RESERED
CV_UNALOC_CODE
CV_INVALID_CODE_FORM
CV_INVALID_FORMAT_OR_ADDRESS_NOT_ENOUGH
CV_ERROR_INCLUDE_LONG_DISTANCE
CV_GSM_CLD_DN_NO_EXIST
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-263
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
ACM
Alerting
Alerting
ACM
REL
Release
Release
REL

IV. Formula
None
8.18.6 Count of Failed Calls Due to Internal Failure
I. Entity Name
SYSFLCL
II. Description
For the requested destination address, the outgoing circuit is available, but the transit
network cannot implement the connection. In addition, there are no other paths
available. The resources cannot be obtained for intra- or inter-module calls.
III. Measurement Point
It is measured when the MSC applies for the internal resources.
1) Call failures due to internal failures (case 1)
The cause value of the Release message may be one of the following.
CV_TEMPORARY_FAILURE
CV_ERROR_FOR_THE_TIME_BEING
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-264
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
REL
Release
Release
REL

2) Call failures due to internal failures (case 1)
The cause value of the Release message may be one of the following.
CV_TEMPORARY_FAILURE
CV_ERROR_FOR_THE_TIME_BEING
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
ACM
Alerting
Alerting
ACM
REL
Release
Release
REL

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-265
8.18.7 Count of Call Failures Due to Overload
I. Entity Name
ALBLCL
II. Description
It is the count of failed calls due to CPU overload.
III. Measurement Point
It is measured when the call is released due to CPU overload (cause#60).
1) Call failures due to overload (case 1)
The cause value of the REL message is CV_CPU_OVERLAP.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
REL
Release
Release
REL

2) Call failures due to overload (case 2)
The cause value of the REL message is CV_CPU_OVERLAP.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-266
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
ACM
Alerting
Alerting
ACM
REL
Release
Release
REL

IV. Formula
None
8.18.8 Count of Call Failures Due to Network Management
I. Entity Name
FWCTLCL
II. Description
It is the count of failed calls due to network management.
III. Measurement Point
It is measured when the call is released due to the network management.
1) Call failure due to network management (case 1)
The cause value of the REL message is CV_NET_MANAGE_BARRING.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-267
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
REL
Release
Release
REL

2) Call failure due to network management (case 2)
The cause value of the REL message is CV_NET_MANAGE_BARRING.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
ACM
Alerting
Alerting
ACM
REL
Release
Release
REL

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-268
8.18.9 Seizure Traffic
I. Entity Name
SERL
II. Description
It is the traffic generated during the incoming call attempts.
III. Measurement Point
It is measured from the moment the IAM or IAI message is received to that the REL
message is received. The final result is indicated in Erlang (ITU-T Rec. Q.722). Point A
in the following figure is the start point of the measurement and B or C is the end point.
IAM
MSC Server
MSC Server
REL
B
REL
C
A
IAM
MSC Server
MSC Server
REL
B
REL
C
A

IV. Formula
None
8.18.10 Answered Traffic
I. Entity Name
RERL
II. Description
It is the traffic generated when incoming calls are in the answered status.
III. Measurement Point
It is measured from the moment the Answer signal message is received from the callee
to that the REL, CLF or CBK message is received. The final result is indicated in Erlang
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-269
(ITU-T Rec. Q.722). Point A in the following figure is the start point of the measurement
and B or C is the end point.
IAM
MSC Server
MSC Server
REL
B
REL
C
ANM
A
IAM
MSC Server
MSC Server
REL
B
REL
C
ANM
A

IV. Formula
None
8.18.11 Count of Circuits in Maintenance
I. Entity Name
MNTCIR
II. Description
It is the count of circuits that are in maintenance state on the outgoing (bidirectional)
trunk.
III. Measurement Point
It is measured when a circuit is in maintenance status.
IV. Formula
None
8.18.12 Answer Rate
I. Entity Name
ANSR
II. Description
Answer rate = Count of answered calls/Count of call attempts
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-270
III. Measurement Point
It is calculated on the BAM.
IV. Formula
ANSR = ANS/ SEIZ
8.18.13 Count of Connected Calls
I. Entity Name
ALTN
II. Description
It is the count of connected calls on the incoming trunk.
III. Measurement Point
It is measured when the MSC sends the ACM to the originating office.
It is measured when the ISUP receives the Alerting message. See point B in the
following figure.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
ACM
Alerting
IAM
Setup
Setup Ack
Alerting
ACM
CCB ISUP(inc)
B
ANM
Connect
Connect Ack
ANM
Connect
Connect Ack
C
A

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-271
8.18.14 Connected Traffic
I. Entity Name
ALTT
II. Description
It is the traffic generated when outgoing calls are in the connected status.
III. Measurement Point
It is measured from the moment the ACM is received from the destination MSC to that
the REL, CLF, or CBK message is sent. The final result is indicated in Erlang (ITU-T
Rec. Q.722). Point A in the following figure is the start point of the measurement and B
or C is the end point.
IAM
MSC Server
MSC Server
ACM
A
REL
REL
B
C
IAM
MSC Server
MSC Server
ACM
A
REL
REL
B
C

IV. Formula
None
8.18.15 Call Completion Rate
I. Entity Name
ALTR
II. Description
Call completion rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-272
IV. Formula
ALTR = ALTN/SEIZ
8.18.16 Count of Callee Power-Off
I. Entity Name
UPOT
II. Description
It is the count of failed call connections (during called number analysis in MSC) due to
callees power-off.
III. Measurement Point
When the MSC analyzes the called number and queries the MSRN of the callee from
the HLR. The HLR returns an indication of callee power-off. The call connection fails
and the measurement begins.
1) Count of Callee Power-Off (case 2)
The cause value of the REL message is CV_GSM_CLD_USER_NOT_ACTIVE.
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
REL
Release
Release
REL

2) Count of Callee Power-Off (case 2)
The cause value of the REL message is CV_GSM_CLD_USER_NOT_ACTIVE.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-273
ISUP(out) MTP MTP
Setup
Setup Ack
IAM
IAM
Setup
Setup Ack
CCB ISUP(inc)
A
ACM
Alerting
Alerting
ACM
REL
Release
Release
REL

IV. Formula
None
8.19 Source TMG Destination Route Traffic
8.19.1 Overview of MS_MGWID_ROUTE_TRAF
The names and meanings are listed in the following table.
Name Description
TMGRTBID Count of seizure attempts
TMGRTSZ Count of seizure
TMGRTACM Count of ringings received
TMGRTANS Count of answered calls
TMGRTCNTR Call completion rate
TMGRTANSR Answer rate
TMGRTSERL Seizure traffic
TMGRTCERL Connected traffic
TMGRTAERL Answered traffic
TMGRTLCR Count of outgoing trunk overflow
TMGRTABR Count of releases before ringing
TMGRTAAR Count of releases before the pickup
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-274
Name Description
TMGRTRNA Count of callee no reply
TMGRTUDB Count of callee determined busy
TMGRTUB Count of callee busy
TMGRTIVA Count of invalid addresses
TMGRTPNR Count of paging no reply
TMGRTAS Count of subscriber absence
TMGRTSSR Count of subscriber service restricted
TMGRTSPT Count of special tones
TMGRTCG Count of peer office congestions
TMGRTIWK Count of interworking failures
TMGRTOTH Count of other failures
TMGRTRES Count of re-routing
TMGRTRESF Count of re-routing failures
TMGRTUMGEF Count of UMG failures
TMGRTNOFRF Count of circuit all busy

8.19.2 Count of Seizure Attempts
I. Entity Name
TMGRTBID
II. Description
It is the count of seizure attempts on the source TMG destination route.
III. Measurement Point
It is measured when the following situations are met:
The MSC finds out the call is a tandem call according to the called number
analysis.
The source TMG number and the destination area index are not null. See point A
in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-275
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.19.3 Count of Seizure
I. Entity Name
TMGRTSZ
II. Description
It is the count of seizures on the source TMG destination route. It is measured after the
successful routing.
III. Measurement Point
It is measured when the following situations are met:
The MSC finds out the call is a tandem call according to the called number
analysis.
The source TMG number and the destination area index are not null.
The route is successfully selected. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-276
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.19.4 Count of Ringings Received
I. Entity Name
TMGRTACM
II. Description
It is the count of alerting on the source TMG destination route. It is measured when the
ACM is received from the backward office.
III. Measurement Point
It is measured when the following situations are met:
The MSC finds out the call is a tandem call.
The source TMG number and the destination area index are not null.
The ACM is received from the backward office. See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-277
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.19.5 Count of Answered Calls
I. Entity Name
TMGRTANS
II. Description
It is the count of ANMs received from the terminating office on the source TMG
destination route.
III. Measurement Point
It is measured when the MSC receives the ANM from the terminating office in a
forwarding call, under the situation that the source TMG number and the destination
area index are not null. See point C in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-278
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.19.6 Call Completion Rate
I. Entity Name
TMGRTCNTR
II. Description
It is the completion rate of the source TMG destination route. It is calculated on the
BAM with the formula (Count of answered calls + Count of subscriber determined call
failures)/Count of call attempts.
III. Measurement Point
It is calculated on the BAM. The formula is: (Count of answered calls + Count of
releases before ringing + Count of callee no reply + Count of callee determined busy +
Count of callee busy + Count of invalid addresses + Count of callee absent + Count of
subscriber service restrictions + Count of special tones)/Count of seizure attempts.
IV. Formula
TMGRTCNTR = (TMGRTANS + TMGRTABR + TMGRTRNA + TMGRTUDB +
TMGRTUB + TMGRTIVA + TMGRTAS + TMGRTSSR + TMGRTSPT)/TMGRTBID
8.19.7 Answer Rate
I. Entity Name
TMGRTANSR
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-279
II. Description
It is the count of answer rate on the source TMG destination route.
III. Measurement Point
It is calculated on the BAM.
Answer rate = Count of answered calls/Count of call attempts
IV. Formula
TMGRTANSR = TMGRTANS/TMGRTBID
8.19.8 Seizure Traffic
I. Entity Name
TMGRTSERL
II. Description
It is the traffic generated during the call attempts on the source TMG destination route.
III. Measurement Point
It is measured from the start of the call attempt to the end of the attempt. Point A in the
following figure is the start point of the measurement.
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-280
8.19.9 Connected Traffic
I. Entity Name
TMGRTCERL
II. Description
It is the traffic generated when calls on the source TMG destination route are in the
connected status. The measurement begins from the moment the phone rings to that
the call is released.
III. Measurement Point
It is measured from the moment the phone rings to that the call is released. See point B
in the following figure.
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.19.10 Answered Traffic
I. Entity Name
TMGRTAERL
II. Description
It is the traffic generated when calls on the source TMG destination route are in
answered status. The measurement begins from the moment the call is answered to
that the call is released.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-281
III. Measurement Point
It is measured from the moment the call is answered to that the call is released. See
point C in the following figure.
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.19.11 Count of Outgoing Trunk Overflow
I. Entity Name
TMGRTLCR
II. Description
It is the count of outgoing trunk overflow on the source TMG destination route.
III. Measurement Point
It is measured when the MSC sends the REL message before the call is connected due
to the outgoing trunk selection timeout or failure. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-282
MSC Server MSC Server
ANM/ANC
A
MSC Server
IAM
RLC
REL

IV. Formula
None
8.19.12 Count of Releases Before Ringing
I. Entity Name
TMGRTABR
II. Description
It is the count of active releases by the callers before calls are connected on the source
TMG destination route.
III. Measurement Point
It is measured when the MSC receives the call release message from a caller before
the call is connected. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-283
MSC Server MSC Server
ACM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.19.13 Count of Releases Before the Pickup
I. Entity Name
TMGRTAAR
II. Description
It is the count of active releases on the source TMG destination route by the callers
before the pickup.
III. Measurement Point
It is measured when the MSC receives the REL message from a caller before the callee
picks up the phone. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-284
MSC Server MSC Server
ACM
IAM
A
MSC Server
IAM
REL
ACM
ANM/ANC
RLC

IV. Formula
None
8.19.14 Count of Callee No Reply
I. Entity Name
TMGRTRNA
II. Description
It is the count of messages indicating that the calls are not replied on the source TMG
destination route because no backward ANM is received.
III. Measurement Point
It is measured when the MSC does not receive the ANM from the terminating office for
a long time. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-285
MSC Server MSC Server
RLC
IAM
A
MSC Server
IAM
REL
ACM
ANM/ANC
ACM

IV. Formula
None
8.19.15 Count of Callee Determined Busy
I. Entity Name
TMGRTUDB
II. Description
It is the count of incoming calls directly rejected by the mobile callees after the ringing
on the source TMG destination route.
III. Measurement Point
It is measured when the MSC receives the REL message from the callee after the
ringing.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-286
MSC Server MSC Server
ACM
IAM
A
MSC Server
IAM
REL
ACM
ANM/ANC
RLC

IV. Formula
None
8.19.16 Count of Callee Busy
I. Entity Name
TMGRTUB
II. Description
It is the count of call connections failed because callees are busy on the source TMG
destination route.
III. Measurement Point
It is measured when the MSC receives the REL message before the call is connected.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-287
MSC Server MSC Server
ACM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.19.17 Count of Invalid Addresses
I. Entity Name
TMGRTIVA
II. Description
It is the count of invalid addresses on the source TMG destination route. The calls are
released before they are connected due to invalid addresses.
III. Measurement Point
It is measured when the call is released due to the invalid address. See point A in the
following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-288
MSC Server MSC Server
ANM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.19.18 Count of Paging No Reply
I. Entity Name
TMGRTPNR
II. Description
It is the count of paging no reply on the source TMG destination route. The calls are
released before they are connected due to paging no reply.
III. Measurement Point
It is measured when the call is released due to paging no reply. See point A in the
following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-289
MSC Server MSC Server
ANM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.19.19 Count of Subscriber Absence
I. Entity Name
TMGRTAS
II. Description
It is the count of subscribers absent on the source TMG destination route. The calls are
released before they are connected due to subscribers absent.
III. Measurement Point
It is measured when the call is released because the subscriber is absent. See point A
in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-290
MSC Server MSC Server
ANM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.19.20 Count of Subscriber Service Restricted
I. Entity Name
TMGRTSSR
II. Description
It is the count of subscriber service restricted on the source TMG destination route. The
calls are released before they are connected due to service restrictions.
III. Measurement Point
It is measured when the call is released because the subscriber service is restricted.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-291
MSC Server MSC Server
ANM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.19.21 Count of Special Tones
I. Entity Name
TMGRTSPT
II. Description
It is the count of special tones on the source TMG destination route.
III. Measurement Point
It is measured when the ACM is received from the backward office, and the message
carries the cause value CV_SEND_PRIVATE_TONE (132). See point A in the following
figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-292
MSC Server MSC Server
IAM
A
MSC Server
IAM
ACM(CV_SEND_PRIVATE_TONE)

IV. Formula
None
8.19.22 Count of Peer Office Congestions
I. Entity Name
TMGRTCG
II. Description
It is the count of peer office congestions on the source TMG destination route.
III. Measurement Point
It is measured when the MSC receives the REL message due to peer office congestion.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-293
MSC Server MSC Server
ANM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.19.23 Count of Interworking Failures
I. Entity Name
TMGRTIWK
II. Description
It is the count of interworking failures on the source TMG destination route. The calls
are released before they are connected due to interworking failures.
III. Measurement Point
It is measured when the call is released due to interworking failure. See point A in the
following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-294
MSC Server MSC Server
ANM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.19.24 Count of Other Failures
I. Entity Name
TMGRTOTH
II. Description
It is the count of other failures without specified cause values on the source TMG
destination route.
III. Measurement Point
The failures are those not specified in this document.
IV. Formula
None
8.19.25 Count of Re-Routing
I. Entity Name
TMGRTRES
II. Description
It is the count of re-routing after the failure on the TMG destination route.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-295
III. Measurement Point
It is measured when the MSC reselect the route after the source TMG destination route
failure.
If it occurs in the local MSC, see point A in the following figure.
MSC Server MSC Server
IAM
A
MSC Server
IAM

If the route is reselected in the originating office after the routing failure in the backward
office, point A in the following figure is the measurement point.
MSC Server MSC Server
IAM
A
MSC Server
IAM
REL

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-296
8.19.26 Count of Re-Routing Failures
I. Entity Name
TMGRTRESF
II. Description
It is the count of re-routing failures after the source TMG destination routing failure.
III. Measurement Point
It is measured when the MSC releases the call due to the re-routing failure.
If it occurs in the local MSC, point A in the following figure is the measurement point.
MSC Server MSC Server
IAM
A
MSC Server
IAM

If the route is reselected in the originating office after the routing failure in the backward
office, point A in the following figure is the measurement point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-297
MSC Server MSC Server
IAM
A
MSC Server
IAM
REL

IV. Formula
None
8.19.27 Count of UMG Failures
I. Entity Name
TMGRTUMGEF
II. Description
It is the count of source TMG destination route failures because the UMG is faulty.
III. Measurement Point
It is measured when the MSC releases the call due to UMG failure. If it is the local UMG
failure, point A in the following figure is the measurement point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-298
MSC Server MSC Server
A
MSC Server
IAM

If it is the backward office UMG failure, point A in the following figure is the
measurement point.
MSC Server MSC Server
IAM
A
MSC Server
IAM
REL

IV. Formula
None
8.19.28 Count of Circuit All Busy
I. Entity Name
TMGRTNOFRF
II. Description
It is the count of all circuits busy which result in the source TMG destination route
failures.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-299
III. Measurement Point
It is measured when the MSC releases the call due to all circuits busy.
If all local circuits are busy, see point A in the following figure.
MSC Server MSC Server
A
MSC Server
IAM

If all backward office circuits are busy, see point A in the following figure.
MSC Server MSC Server
IAM
A
MSC Server
IAM
REL

IV. Formula
None
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-300
8.20 Transit Traffic
8.20.1 Overview of MS_OFFICE_TRN_TRAF
The names and meanings are listed in the following table.
Name Description
OTKBID Count of outgoing trunk seizure attempts
OTKSEIZ Count of outgoing trunk seizure
CNT Count of connected calls
ANS Count of answered calls
BRGABN Count of releases before ringing
LRUOFL Count of outgoing trunk overflow
CBSY Count of callee busy
SERL Seizure traffic
ALTT Connected traffic
RERL Answered traffic
CNTR Call completion rate
ANSR Answer rate
TRNSEIZ Count of call attempts
DWNT Count of wrongly dialed numbers
CFCR
Count of failed call attempts due to common resource
application failure
POCT Count of peer office congestions
CRAR Count of releases before the pickup

8.20.2 Count of Outgoing Trunk Seizure Attempts
I. Entity Name
OTKBID
II. Description
It is the count of seizure attempts on outgoing trunk circuits in the forwarding calls.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-301
III. Measurement Point
It is measured when the MSC selects the route for the callee after the number analysis.
See point A in the following figure.
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.20.3 Count of Outgoing Trunk Seizure
I. Entity Name
OTKSEIZ
II. Description
It is the count of successful seizures on outgoing trunk circuits in the forwarding calls.
III. Measurement Point
It is measured when the MSC receives the ACM which indicates the call successfully
seizes the trunk circuit.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-302
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.20.4 Count of Connected Calls
I. Entity Name
CNT
II. Description
It is the count of ACMs sent to the originating office in the forwarding calls.
III. Measurement Point
It is measured when the MSC sends the ACM to the originating office after receiving the
ACM from the terminating office. See point B in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-303
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.20.5 Count of Answered Calls
I. Entity Name
ANS
II. Description
It is the count of forwarding calls answered.
III. Measurement Point
It is measured when the MSC receives the ANM. See point C in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-304
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.20.6 Count of Releases Before Ringing
I. Entity Name
BRGABN
II. Description
It is the count of active releases by the callers before the fixed-line callees' phones ring
in the forwarding calls.
III. Measurement Point
It is measured when the MSC receives the REL or CLF message from a caller before
the call is connected. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-305
MSC Server MSC Server
ACM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.20.7 Count of Outgoing Trunk Overflow
I. Entity Name
LRUOFL
II. Description
It is the count of failures of outgoing (bidirectional) trunk seizure attempts originated by
the MSC in the forwarding calls.
III. Measurement Point
It is measured when the MSC fails to select an internal outgoing trunk (bidirectional) in
a forwarding call. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-306
MSC Server
IAM
A
Outgoing trunk
overflow
MSC Server
MSC Server
IAM

IV. Formula
None
8.20.8 Count of Callee Busy
I. Entity Name
CBSY
II. Description
It is the count of call connections failed because callees are busy in the forwarding
calls.
III. Measurement Point
The MSC receives the REL message. If the cause value in the message is
CV_SL_BUSY or CV_ST_BUSY, or CV_BUSY in an outgoing call, the measurement
begins. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-307
MSC Server MSC Server
ACM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.20.9 Seizure Traffic
I. Entity Name
SERL
II. Description
It is the traffic generated during the forwarding call attempts.
III. Measurement Point
It is measured from the moment the IAM or IAI message is sent to the destination MSC
to that the REL message is received. The final result is indicated in Erlang (ITU-T Rec.
Q.722).
Point A in the following figure is the start point of the measurement and call release is
the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-308
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.20.10 Connected Traffic
I. Entity Name
ALTT
II. Description
It is the traffic generated when forwarding calls are connection status.
III. Measurement Point
It is measured from the moment the ACM message is sent to the source MSC to that
the REL message is sent to the destination MSC. The final result is indicated in Erlang
(ITU-T Rec. Q.722).
Point B in the following figure is the start point of the measurement and call release is
the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-309
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.20.11 Answered Traffic
I. Entity Name
RERL
II. Description
It is the traffic generated when forwarded calls are in the answered status.
III. Measurement Point
It is measured from the moment the Answer signal is sent to the source MSC to that the
REL message is sent to the destination MSC. The final result is indicated in Erlang
(ITU-T Rec. Q.722).
Point C in the following figure is the start point of the measurement and call release is
the end point.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-310
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.20.12 Call Completion Rate
I. Entity Name
CNTR
II. Description
Call completion rate = Count of connected calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
IV. Formula
CNTR = CNT/TRNSEIZ
8.20.13 Answer Rate
I. Entity Name
ANSR
II. Description
Answer rate = Count of answered calls/Count of call attempts
III. Measurement Point
It is calculated on the BAM.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-311
IV. Formula
ANSR = ANS/TRNSEIZ
8.20.14 Count of Call Attempts
I. Entity Name
TRNSEIZ
II. Description
It is the count of incoming trunk call attempts in which the calls are found out to be the
tandem ones by analyzing the called numbers.
III. Measurement Point
After receiving the IAI or IAM message from the originating office, the MSC analyzes
the called number. It is measured when the MSC finds that the call is a tandem one.
See point A in the following figure.
MSC Server MSC Server
ACM
IAM
ANM/ANC
C
A
B
MSC Server
ACM
ANM/ANC
IAM

IV. Formula
None
8.20.15 Count of Wrongly Dialed Numbers
I. Entity Name
DWNT
II. Description
It is the count of wrong numbers dialed in the forwarding calls, which result in call
connection failures.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-312
III. Measurement Point
It is measured when the MSC sends the REL (unallocated number or incomplete
address) message to the originating office after receiving the same message from the
terminating office. See point A in the following figure.
MSC Server MSC Server
ACM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.20.16 Count of Failed Call Attempts Due to Common Resource Application
Failures
I. Entity Name
CFCR
II. Description
It is the count of call failures caused by common resources unavailable on the MSC,
including the IWF, bill pool, control table, and announcement resources.
III. Measurement Point
It is measured when the MSC fails to allocate the internal common resources. See
point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-313
MSC Server MSC Server
ACM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.20.17 Count of Peer Office Congestions
I. Entity Name
POCT
II. Description
After the MSC sends the IAM or IAI to the peer office according to the routing
information in an outgoing call, the peer office or the terminating office returns an
unexpected backward message (excluding callee busy, invalid address) to indicate that
the call cannot be connected. This entity is the count of call connection failures in such
situation.
III. Measurement Point
It is measured in one of the following cases.
After sending the IAM, the MSC releases the call due to no response from the peer
office in a valid period.
The MSC fails to select an internal outgoing (bidirectional) trunk in a forwarding
call.
See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-314
MSC Server MSC Server
ACM
IAM
A
MSC Server
IAM
REL
RLC

IV. Formula
None
8.20.18 Count of Releases Before the Pickup
I. Entity Name
CRAR
II. Description
It is the count of active releases by the callers before the pickup in the forwarding calls.
III. Measurement Point
It is measured when the MSC receives the REL message from a mobile caller before
the callee picks up the phone. See point A in the following figure.
Technical Manual Performance Measurement Entities
HUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 8 Total Traffic of the Office

Huawei Technologies Proprietary
8-315
MSC Server MSC Server
ACM
IAM
A
MSC Server
IAM
REL
ACM
ANM/ANC
RLC

IV. Formula
None

Das könnte Ihnen auch gefallen