Beruflich Dokumente
Kultur Dokumente
College name
Address
college
LOGO
..
. ..
..
2014-2015.
Staff-in-charge
..
Internal Examiner
External Examiner
admbe0011@gmail.com
S.
No
Marks Awarded
Date
Initials
Lab Exp
(10)
Obser
(10)
Average
admbe0011@gmail.com
Viva
(10)
Record
(10)
TOTAL
(40)
Ex.no.:
INTRODUCTION TO AUTOCAD
Date:
METRIC
Creates a new drawing based on metric measurement. The drawing is based on
ocadiso.dwt template. Save drawing files for later use.
admbe0011@gmail.com
UNITS
Every object is measured in units. In AutoCAD we can determine the value of
the units before we draw.
LIMITS
The drawing limits are two-dimensional points in the world coordinate that
represent a lower-left limit and an upper right limit. You cannot impose limits on the
Z direction.
POLYLINE
PLINE command allows you to draw line and arc segments, but from start to
end, it is treated as a sing object. With PLINE command, you can draw objects even
with line width.
admbe0011@gmail.com
ARC
The ARC command allows you to create an arc segment. There are different
methods of creating an arc. The different methods of creating an arc are:
1)3 Points
2)Centre, Start, Radius
3)Start, Centre, End
4)Start, Centre, Angle
5)Start, Centre, Length
6)Start, End, Angle
7)Start, End, Direction
8)Start, End, Radius
CIRCLE
The CIRCLE command allows you to create a circle. There are four different
methods for drawing circles. They are:
Centre, Radius/Centre, Diameter
3 Points (3P), 2 Points (2P)
Tangent, Tangent, Radius (ttr)
POLYGON
Polygon command creates a regular polygon. You must specify the number of
sides of the polygon and whether it is Inscribed or Circumscribed polygon. Now,
specify the centre and radius of the polygon circle.
OSNAP
Osnaps allow you to snap onto a specific object location when you are picking
a point. For example, using Osnaps you can accurately pick the end point of a line or
the center of a circle.
ERASE
This command is used for deleting unwanted objects. You must select the
object to be erased.
admbe0011@gmail.com
COPY
The copy command is used for making copies of selected objects. The object
to be copied must be selected and the base point must be specified and the copy can
be dragged and placed at the required position.
MOVE
This command is used for moving selected objects. The object to be moved
must be selected and its base point must be specified then we can drag it to the
required location.
ROTATE
This command is used for rotating selected objects. To rotate an object, first
select it and specify a base point. Now enter an angle value or specify a second point
to rotate the object.
Entering a positive angle value rotates the objects counterclockwise or
clockwise, depending on the Direction Contorl Control setting and Drawing Units
dialog box. The plane of rotation and the direction of the zero angle depend on the
orientation of the user coordinate system.
MIRROR
The MIRROR command is used for creating mirror images of selected objects.
You must first select the object to be mirrored and then specify the axis along which
it is mirrored, to create an mirror image of the selected object.This is a very useful
command for drawing symmetrical objects about a particular axis.
OFFSET
Offset an object to create a new object whose shape parallels the shape of the
original object. Offsetting a circle or an arc creates a larger or smaller circle or arc,
depending on which side you specify for the offset.
admbe0011@gmail.com
POLAR ARRAY
This command creates an array of the selected object around a centre point.
You must specify the centre point of the array, the total number of items and the
angle to fill for creating a polar array.
RECTANGULAR ARRAY
This command creates an array of the selected objects defined by the number
of rows and columns and the offset between them.
EXTEND
The EXTEND command elongates the selected objects to a specified
boundary.
TRIM
The TRIM command trims off an object using cutting edges defined by other
objects. Here the user is required to select object(s) to define cutting edge(s) then
select the object to be trimmed, the selected side of the object is removed based on
the side of selection of the object to be trimmed relative to the cutting edge.
BREAK
The BREAK commands is used to remove only parts of an object. You must
specify the first and second points between which the object must be deleted.
FILLET
FILLET rounds of the edges of two arcs, circles, elliptical arcs, lines,
polylines, rays, splines or xlines with an arc of a specified radius. Rounds along the
edges cannot be created with zero radius.
admbe0011@gmail.com
CHAMFER
CHAMFER command draws a line at the corner between two selected lines. If
the lines do not intersect, it extends the lines. If they intersect, the lines extending
beyond the chamfer line can be trimmed or left as it is, by the trim mode.
LENGTHEN
The LENGTHEN command is used to increase/decrease the length of
AutoCAD objects.
DIVIDE
This command places evenly spaced point objects or blocks along the length or
perimeter of an object. You can select only one entity at a time to be divided. The
entities that can be selected are: line, arc, circle, polyline and spline.
ZOOM ALL
This zoom to display the entire drawing in the current viewport. The display
shows all the entities even if the drawing extends outside the drawing limits.
ZOOM WINDOW
ZOOM WINDOW commands to display an area specified by two diagonally
opposite corner points of a rectangle window.
ZOOM EXTENTS
This zoom to display the drawing extents. If the drawings are small in the
existing limits, then there is an enlarging effect on the screen. If the drawing occupy
the complete area of the limits, then there are many not be much difference between
ZOOM ALL and ZOOM EXTENTS.
DIMLINEAR
This command specifies the linear distance between two selected points.
admbe0011@gmail.com
DIMALIGNED
This command is used for specifying the linear distance (exact dimensional
value) between two points which are inclined at an angle.
DIMANGULAR
This command is used for obtaining the angle two selected points. The three
types are:
1)Arc Selection
2)Circle Selection
3)Line Selection
4)Three Point Selection
DIMRADIUS
This command gives the value of radius of the specified circle, arc or fillet. A
radial dimension consists of a radius dimension line with an arrowhead at the arc or
circle end.
DIMCENTER
This command marks the centre point of the selected arc or circle. The center
mark cannot be updated, so set the required style before executing this command.
LINETYPE
LINETYPE greatly improves the readability of technical drawings. You can
make important features stand out with bold line weights.
LAYER
Layer is an organizing tool. Layers are like one, where you can keep various
types of information. Its always a good idea to keep notes and reference symbols
about each element of the drawing as well as drawing dimensions on a new layer.
admbe0011@gmail.com
DISTANCE
This command lists the distance between the selected points and also lists out
the angle in current plane and 3D angle from the current plane, based on the direction
of picking the two points. It also lists the projected lengths on the three axes called
the delta length.
TEXT
TEXT command creates text objects with specified height and orientation.
Text objects can be created with a variety of character patterns call style. This
command allows you to type a single line or multiple lines of text.
MTEXT
MTEXT creates paragraph that fit within a nonprinting text boundary. The
user specified text boundary determines the width of the paragraph and the
justification of the text within the paragraph. Each multiline text object is a single
object, regardless of the number of lines it contains.
HATCH
Hatches are shaded pattern which generally represent cross-section of a
mechanical component. Using BHATCH command the required area, type of hatch,
hatch angle and scale can be specified.
PROPERTIES
The PROPERTIES command displays the Properties palette. The Properties
palette is the main method for viewing and modifying the properties of AutoCAD
objects.
VPORTS
Viewports are areas that display different views of your model. As you work
on the Model tab, you can split the drawing area into one or more adjacent
rectangular views known as model space viewports. In large or complex drawings,
admbe0011@gmail.com
displaying different views reduces the time needed to zoom or pan in a single view.
Also, errors you might miss in one view may be apparent in the others.
EXTRUDE
Solids can be created by extruding selected objects. Use the EXTRUDE
command to create a solid or surface from a common profile of an object
REVOLVE
REVOLVE command can create a solid or surface by revolving open or
closed objects about an axis. The revolved objects define the profile of the solid or
surface.
PYRAMID
This command can create a solid pyramid. The number of sides for a
pyramid, from 3 to 32, can be defined. The axis endpoint defines the length and
orientation of the pyramid.
CREATE LAYOUTS
A layout stimulates a sheet of paper and provides a predictable plotting setup
for a layout, you can create and position view post objects and you can add a title
block or other objects geometry.
PLOT DRAWINGS
Once you have completed a drawing you can plot the drawing on paper or
create a file for use with another application. In either case, you select the plot
settings.
admbe0011@gmail.com
Ex.no.:
Date:
Aim:
Setting up of drawing environment by setting drawing limits, drawing units, naming
the drawing, naming layers, setting line types for different layers using various type of lines in
engineering drawing, saving the file with dwg extension.
Software Used:
Auto CAD 2012
Commands Used:
Limits, units, layer
THEORY:Setting up drawing limits:i) Menu bar: - Format > Drawing limits
OR
ii)Command:- limits
Set the drawing areas by limits command. First enter the limits command. It will display the
prompt to specify the lower left corner and then the next prompt is specify the upper right
corner .
The following is the prompt sequence of the limits command for setting limits.
Specify lower left corner or [ON/OFF]
: 0, 0
Specify upper right corner
: 10,10
Setting up drawing Units:i) Menu bar: - Format > units
OR
ii)Command:- units
The units command is used to select a format for the unit of distance and angle measurement.
After entering the units command it will display the Drawing Units dialog box which is used to
set the units and angles. Then specify the Precision for the units and angles from the
corresponding precision drop-down list. After selecting all the set-up press OK.
Setting up drawing Layers:i) Menu bar :- Format > layer
OR
ii)Command:- layer
admbe0011@gmail.com
After entering the Layer command it will display the Layer Properties Manager dialog
box. You can create new layers with assign a new line-types, layers name and line colour.
Procedure for create a new layer:Choose the new button in the Layer Properties Manager dialog box. A new layer with name
Layer 1 is created. Now type the name of the new layer.
Procedure for setting the line type:To assign a new line-type to a layer, click in the current line type displayed with a
particular layer in the Layer
Properties Manager dialog box.
After clicking in the line-type. Auto CAD will display the select line-type dialog box. Click
on the Load button and select the new line-type form the Load or Reload dialog box and then
choose the OK button.
Procedure for save a file:The drawing must be saved before exit from the file.
i) menu bar :- File > save or save as
OR
ii) Command:- save or qsave.
After entering the save command it will display a Save Drawing As dialog box. Select the
proper place and type the file name. Select file-types and then click Save button. Note:- All the
drawing files save with dwg extension.
admbe0011@gmail.com
Ex.no.:
Date:
Aim:
Draw Different type s bolts and nuts with internal and external threading in Acme and Square threading
standards. Save the bolts and nut as blocks suitable for insertion.
Procedure:List of commands for drawing bolts and nut.
i)
ii)
iii)
iv)
v)
vi)
Polygon
Circle
Line
Line type (Center line, Hidden line etc.)
Hatch
Block
i) Polygon:A regular polygon is a closed geometric figure with equal sides and equal angles. The number of
sides varies from 3 to 1024.
Command: polygon
Command: Enter number of sides <4>: (Ex: 6)
Specify center of polygon or [Edge]: (Ex: 10, 10)
Enter an option [Inscribed in circle/Circumscribed about circle] <I>: I ( I or C )
Specify radius of circle: (Ex: 50)
ii) Circle:Command: circle
Command: _Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: (Ex: 10, 10)
Specify radius of circle or [Diameter]: (Ex: 50 or d )
iii) Line:Command: line
Command: Specify first point: (Ex: 10, 10) Specify next point or [Undo]: (Ex: 100, 100)
iv) Line type:Command: line type
Format > Line type (It will display a Line type Manager Dialog box) > Load > select the required linetype
from the given linetype list > ok.
v) Hatch:Command: bhatch
The Hatch command allows you to hatch a region enclosed within a boundary (closed area) by selecting a
point inside the boundary or by selection the objects to be hatched.
admbe0011@gmail.com
Draw > Hatch (It will display a Boundary Hatch and Fill dialog box) > specify Hatch type > Hatch pattern >
Angle > Scale > Choose pick point (select any point inside the object) or Select object >Choose Preview or
Ok.
vi) Block:Command: _block
Draw > Block > Make (it will display a Block Definition dialog box)
a)
Specify the Block Name.
b)
Specify the insertion Base Point (This point is used as a reference point to insert the block by choosing
Pick Point)
c)
Select object. d)
OK.
Command: Insert
Insert > Block > Select the Block Name from the drop down list > Ok.
admbe0011@gmail.com
Ex.no.:
Date:
Aim:
To create simple objects like polygon and general multi-line
figures using Auto CAD software.
Software Used:
Auto CAD 2012
Commands Used:
Limits, Zoom, Line, Arc, Circle, co-ordinate systems, Dimlinear
Procedure:
1) Limits are set for A4 standard drawing size. Margins are drawn using lines.
2) Using Line command and appropriate co-ordinate system, the given figures
are drawn and aligned
3) The drawn figures are dimensioned using respective DIM command.
4) Title Block is drawn for the given dimension.
5) Finished work sheet is saved and hard copy is taken.
Result:
The given simple figures like polygon and general multi-line figures are drawn
using Auto CAD software.
admbe0011@gmail.com
2D VIEWS OF PLAN
Ex.no.:
Date:
Aim:
To
draw
the
2D
views
from
the
given
plan
CAD software.
Software Used:
Auto CAD 2012
Commands Used:
Limits, Zoom, Line, Polygon, Arc, Circle, Offset, Copy,
Move, Trim, Layer, DIM.
Procedure:
1) Limits are set for plan dimension size. Margins and title block are
drawn using lines.
2) Using appropriate commands, front, top and Left side view of given solids
are drawn.
3) Layer is defined (for line type, line weight and colour) sepeartely for
visible, hidden, axis and dimension lines and applied.
4) Drawn solids are dimensioned accordingly.
5) Finished work sheet is saved and hard copy is taken.
Result:
The orthographic views of the given solids are drawn using Auto CAD.
admbe0011@gmail.com
"
"
"
"
"
%
)
"
"
"
"
"
"
"
'
'(
"
&
"
"
"
"
"
"
"
"
"
"
"
"
admbe0011@gmail.com
Ex.no.:
Date:
Aim:
To create the plan of given residential building using Auto CAD software.
Software Used:
Auto CAD 2012
Commands Used:
Limits, Zoom, Line, Offset, Copy, Move, Multiline.
Procedure:
1) Limits are set for drawing size. Margins and title block are drawn
using lines.
2) Using Mulitline command, plan of the given residential building is drawn.
3) The plan is dimensioned and the rooms are named accordingly.
4) Finished work sheet is saved and hard copy is taken.
Result:
The plan of the given residential building is drawn using Auto CAD.
admbe0011@gmail.com
REAR
SET BACK
X
WD
KIT
PROJECTION
W
W
ROOM
7 X
W
C OPEN
7X
ROOM
7 X
VER
UP
TOILET
X
D
V
PROJECTION
FOR GALI
WD
VER
UP
TOILET
X
PROJECTION
STORE
PROJECTION
W
W
ROOM
7 X
W
C OPEN
7X
ROOM
7 X
W
7 WD
TARRACE
OPEN
SLOP
DN
DOOR
D
D
W
W
V
G
PARTICULERS
WINDOW
VENTILATOR
GATE
AREA
GF
COVERED
OPEN
COVERED
COVERED
TF
GF
FF
TOTAL COVERED
DRAIN
REFERENCE
PROPOSED WORK
SEPTIC TANK
DN WATER PIPE
ELECTRIC LINE
TELIPHONE LINE
X
7 X
X
X
X
X
ST
PLAN
SITE PLAN
FOUNDATION
KEY PLAN IS NOT SCALE
ALL DAIMENSIONS ARE IN METER
SCALE
]WXZ
W
7 WD
GATE
WD LEFT
SET BACK
RESIDENTIAL HOUSE UP TO
HOUSE OF SRI SHYAM SAVITA
S
W
PL
GL
THICK C C FLOORING
C C BASE
WW WW WW WW
-*..,
E
N
THICK D P C
EW
OVER
FOUNDATION
SPECIFICATION
CC
WITH CEMENT SAND
CM
GAUGE B B IN FOUNDATION
IST CLASS B W
WITH CEMENT SAND
IN FOUNDATION
CM THICK D P C
WITH CEMENT
COURSE SAND STONE GRITE DAMP
PROOF COMPOUND
IST BRICK WORK
WITH CEMENT
SAND
MM THICK PLASTER
WITH CEMENT
SAND
RCC
WITH CEMENT COURSE SAND
CM GAUGE STONE GRITE
PROPOSED BUILDING
PLAN OF
SITUATED
KALYAN NAGAR
BHARTHANA ETAWAH
DRAWN BY
OWNERS SIG
jk
V Z [
cZ W^a [YaZ ]a
WYXaZ a aW
WW W W
W[
_^
[_Z
WW _[Z
_]
W
W
c
[_] W WWW W [_^
[_
[_
_]Z
]
b
b
W
W
c
c ]c
c
admbe0011@gmail.com
c
XW\
SECTION ON A3B
XW] [VWY WX
Y Y
[W^ [W^Y W]Z
Y X
[WY W\X[
Z
[WY XW
Z ]Y
EW
* *
lmd
WW
DRAIN
WW
WW
REAR
R C C SLAB
***
**
G* L*
PL
T
R
-*0-
5 -*+,
5 -*.4
Y
OPEN
7X
DRAIN
FRONT ELEVATION
XW[
WD
RESIDENTIAL PLOT
SITE PLAN
.*,+
2*-,
Y
W X
W[[
XWV
.*,+
-*..,
-*4-* 7,
-* 7,
-*4WW
MKN
Y
2*-,
W
-*..,
X
-*4-* 7,
YZ
XWX
XWV
+*-0
.*-+ [
W]X
XWVZ
VW]
[Wi
\ W [
Z
VW]
VW]
XW\
X
Y
[Wi
XW
]
[Wi
[
[ iWX
[WY
fY [WY
Xgh ]Z
W]Z
iWZ
PROJECTION
WD
-* 7,
Y
.,*+1
WZ
XW
VW] W
[Wi
\ W [
XW\
[YW
-*7,
-*4V
X
+*11
PARAPIT
XWZ
^
XW]
XW\
;9<
NKO
@D?
UP TO
V
[Wi
[
X
[WY
RESIDENTIAL PLOT
XgZh
]
VW]
VW]
VWX
X
9:
M
HID
OF SRI SURESH
Y
^W[
X
678
JKL
SET
]Z
PLOT
Xf
X
Y
[Wi
Z
]W
XW
XWV
Y
C?D >@?
EF BA
]Z
.,*+1
Y
SIDE
G@>
nopn
OF
PLOT
UP TO
[Wi
^W[
^W[
XW
W]Z
4*1,X .*++
SIDE SET BACK
WiZ
PROJECTION
-* 7,
WD
W]Z
[YW
SMT
* RINKY
BACK PQRS X TQUU
WiZ
[Wi
X
RESIDENTIAL HOUSE
VWX
Ex.no.:
Date:
Aim:
To create 3-D Models of given simple solids and obtain 2-D multi
view drawings Auto CAD software.
Software Used:
Auto CAD 2012
Commands Used:
Zoom, Line, Polygon, Arc, Circle, DIM, Extrude, Revolve, Pyramid.
Procedure:
1) Auto CAD 3-D template is opened for creating 3-D models.
2) Prisms are created using Extrude command and pyramids by Pyramid
command.
3) Objects of revolution like cylinder and cone are created using Revolve
command.
4) Finished work sheet is saved and hard copy is taken.
Result:
3-D Models of given simple solids are created using Auto CAD.
admbe0011@gmail.com
admbe0011@gmail.com
Ex.no.:
Date:
Aim:
To create the plan of 3D rendering and setting using Auto
CAD software & 3D modelling softwares
Software Used:
Photoshop Auto CAD & 3D modelling softwares (sketch up, rivet)
Procedure:
is
created
with
Left Side
four
viewports
for
Result:
admbe0011@gmail.com
Front,
Top,
admbe0011@gmail.com
Ex.no.:
Date:
2D-PROJECT
Commands Used:
Procedure:
admbe0011@gmail.com
Ex.no.:
Date:
3D-PROJECT
Aim: To create 3-D PROJECT using Auto CAD & 3D modelling softwares
(sketch up,rivet)
Software Used:
Auto CAD & 3D modelling softwares (sketch up,rivet)
Commands Used:
Procedure:
admbe0011@gmail.com