throughput issue 2014-10-17 Huawei Confidential 1.Problem description We have noticed that during the Auto Ping function from RNC to !" the throughput changed occasionally after disconnecting and connecting again with the S# datacard$ Without changing the radio conditions at all" the CD% throughput could &e either '()&ps or *()&ps +,igure -.$ Figure 1: Occasional ping throughput reduction after VMC re- connections %he pause period &etween the connections was only a few seconds and the ! position remained e/actly the same$ 2.Problem Analsis !very time a ! is connected to the networ0" RNC allocates a Chip 12set to this !$ ,or DC service" the Chip 12set has an optimal value which can ensure the highest performance of the DC user$ %he optimal value for the Chip 12set in Huawei RNC is 3(-'4$ When the Chip 12set assigned to the DC-! is 3(-'4 the ma/imum performance is guaranteed$ %he optimal Chip 12set is directly connected to the ! response performance$ ,rom the collected traces of RNC and Node# CD% during the tests" we have found that sometimes RNC did not allocate the optimal Chip 12set to the user +,igure '.$ Figure 2: Chip o!set is not the optimal 5n these cases the Node# would not receive AC67NAC6 info on time from the ! +,igure *.$ %herefore" the DC user schedule rate was reduced" and the DC user4s throughput was less than its ma/imum capa&ility$ 10/17/2014 Huawei Technologies Co., Ltd. Figure ": #ode$ does not recei%e &C-AC' in time )ore speci8cally" in ,igure * the red mar0ed trace records show that many times the Node# does not receive the DC-AC6 over the HSDPCH in time during the 8rst 'ms frame" and waits for the ne/t 'ms$ %his issue causes the DC ser4s throughput to drop$ ".(olution 5n the current RNC software version +SPC'99." a Chip 12set optimi:ation algorithm is included which can &e activated using the following two )); commands$ SET URRMCDLCFG: INNERSWITCH3=RESERVED_SWITCH_BIT_0-1; MOD UCELLALGOSWITCH: CellId=! R"#d$%&%3='; (()*& +*,- .%&&/e&" %he 8rst command opens the algorithm switch in RNC level" &ut it will not &e e2ective unless the second command is e/ecuted in cell level$ 5n order for this function to &e e2ective" Node# RAN-' SPC''9 patch or later is also needed$ When this algorithm is activated" RNC will guarantee the optimal Chip 12set for the DC-users in order to achieve the highest DC performance$ %his change can &e implemented in live networ0 without any ris0s$ %his function is used only for optimi:ation of DC and )5)1 users4 performance +<see note &elow.$ %here is no other e2ect on plain HSPA users or legacy !s$ After activating the optimi:ation algorithm in the %est RNC" the CD% auto-ping performance was sta&le= Figure ): (table auto-ping performance *MPO+,A#, #O,- The above issue can also occur for MIMO users. However, the reduction in MIMO throughput in this case could be of 1-2Mbps. This optimiing algorithm can enhance the MIMO user!s throughput. The optimiation in MIMO case is about 1-2Mbps. Therefore, Huawei suggests opening this function in MIMO cells as well. Of course, "#$12 %&'22( or later 10/17/2014 Huawei Technologies Co., Ltd. $ode) patch is needed, as alread* mentioned. ).Function &eacti%ation 5n case we want to deactivate the optimi:ation algorithm we need to e/ecute the &elow commands= SET URRMCDLCFG: INNERSWITCH3=RESERVED_SWITCH_BIT_0-0; MOD UCELLALGOSWITCH: CellId=! R"#d$%&%3=0; (()*& +*,- .%&&/e&" 10/17/2014 Huawei Technologies Co., Ltd.