Beruflich Dokumente
Kultur Dokumente
.INNOMAG.
Page 1 of 65
Page 2 of 65
Document Description
Thrust Balancing
Solids Handling
10
11
12
14
Item List
16
Pump Configuration
17
10
18
11
Hydraulic Coverage-50Hz
21
12
Hydraulic Coverage-60Hz
22
13
23
14
27
15
29
16
52
17
54
18
65
Page #
Page 3 of 65
Page 4 of 65
Page 5 of 65
Page 6 of 65
Discharge Pressure
Suction Pressure
Fixed Orifice
Clearance:0.005
Regulates Flow
A4
A2
A3
A1
Variable Orifice
Regulates Pressure
The balancing system is responsive, automatic and stable with any change in the fluid conditions such as flow,
pressure or viscosity.
Operate with less power by eliminating axial thrust loads. Less friction, less power.
Expanded operating range, engineered to perform continuously over the entire flow range.
Increased pump life and reliability with no forward thrust.
Page 7 of 65
The forces acting on each of these areas is the product of the area times the pressure and the sum of the forces on the
front must equal the sum of forces on the back. This can be written as:
P1*A1+P2*A2 = P3*A3+P4*A4
Where P1 is the suction pressure, P2 is discharge, P3 is the balance chamber pressure and P4 is also discharge
pressure.
Now, P2 = P4 and P1=0 then,
P3*A3=P4*(A2-A4)
or
P3=P4*(A2-A4)/A3
In the TB-mag design, A2>A4 so P3 is a positive value and solely a function of the discharge pressure and the areas of
the impeller wear rings.
The second important concept in the TB-mag system is how the pressure, P3 acting on area A3 is kept at exactly the
value required to balance the system. This is accomplished by allowing the impeller to float freely in the axial direction. If
the forces on the back of the impeller are greater than those on the front then the impeller is displaced forward (towards
the suction). This causes the clearance between the valve and the end of the shaft to increase. This allows more fluid to
exit from area A3 and drops pressure P3 until P3 again balances the forces. Displacement of the impeller towards the
back causes the valve-to-shaft clearance to decrease, increasing the P3 until it balances the system. Pressures in areas
A1, A2 and A4 are not affected by the impeller movement. In practice this is a very stable control system that requires
pressure to operate. This system
works effectively from the minimum
1000
thermal flow limit (typically a few
900
gpm) to run-out provided the pump
800
is generating pressure.
700
600
500
400
300
200
100
0
6"
8"
10"
TB-Mag
Other
Sealless
Pumps
Page 8 of 65
Back
Wear
Rings
Front
Wear
Rings
Clean,
Filtered
Liquid
Liquid/Solids:
Microns to
Figure 1 - Solids passing through the pump
Solids Handling Considerations
Maximum
Pump Life
Minimum
Pump Life
Low percentage of solids
Fine, smooth, spherical shaped particles
Softer particles or flakes
Suspended, uniform solids
Low or variable speed operation
Operate at or near BEP
Continuous Duty
Page 9 of 65
No wear on
the casing
lining.
Vanes eroded
away separating
the back and front
shrouds.
No wear on
the inner
magnet
assembly.
Page 10 of 65
Same impeller
looking at the
stainless cover over
the magnets.
Page 11 of 65
OUT
1
3
IN
2
Figure 1 TB-mag Flow Path
Page 12 of 65
Drive Torque
Pump Size
STD.
Drive Torque
(1.5 x 1 x 6)
AA
0,1
(1.5 x 1 x 6) Low Flow
AA
0,1
(3 x 1.5 x 6)
AB
0,1
(3 x 2 x 6)
-0,1
(1.5 x 1 x 8)
AA
0,1
(1.5 x 1 x 8) Low Flow
AA
0,1
(3 x 2 x 6)
-0,1
(3 x 1.5 x 8)
A50
0,1
(3 x 2 x 6)
A10
0,1
(4 x 3 x 6)
-0,1
(3 x 2 x 8)
A60
0,1
(4 x 3 x 8)
A70
0,1
(2 x 1 x 10)
A05
0,1
(2 x 1 x 10) Low Flow
A05
0,1
(3 x 1.5 x 10)
A50
0,1
(3 x 2 x 10)
A60
0,1
(4 x 3 x 10)
A70
0,1,2
(4 x 3 x 10H)
A70
0,1,2
(6 x 4 x 10H)
A80
0,1,2
(6 x 4 x 8)
A80
0,1,2
(2 x 1.5 x 6) Vertical
2015/15
0,1
(2 x 1.5 x 8) Vertical
2015/15
0,1
Max.
6.65"
6.65"
6.65"
6.65"
8.25"
8.25"
7.00"
8.25"
7.00"
7.00"
8.25"
8.25
10.5"
10.5"
10.5"
10.5"
10.5"
10.5"
10.5"
8.25"
6.65"
8.25"
Min.
4.00"
4.00"
4.00"
4.00"
5.50"
5.50"
5.50"
5.50"
5.50"
5.50"
5.50"
5.50"
5.50"
5.50"
5.50"
5.50"
5.50"
8.00"
8.00"
5.50"
4.00"
5.50"
0
1
2
Motor Frame
NEMA C-Face
A B C ta
D ta
E F -
Impeller Diameter
Bearing System
C
Bushing
SiC
SiC+DLC
Shaft, Pump
SiC
SiC+DLC
1
2
3
4
Gasket
S
1
2
3
IEC B5
M
N
P
Q
ta
R
S
T
tc
U
tc
V
uc
W
80
90S/L
100L
112M
132S/M
160M
160M/L
180M/L
200L
225S/M
(A Series Only)
(Max. A-Series)
(Max. B-Series)
G
H
J
K
(A Series Only)
56C
143/5TC
182/4TC
213/5TC
254/6TC (Max. A-Series)
254/6 (4 Pole)
284/6TSC(Max. B-Series)
324/6TSC
364/365TSC
284/6TC
324/6TC & 405TSC
tc
uc
* 665
inches, (example: 665 = 6.65")
* Impeller trim for ANSI models must be specified in inches.
1
2
Standard Torque
High Torque
Ultra High Torque
Product Group
SiC
SiC
SiC
SiC+DLC
SiC
CF PTFE
SiC
SiC+DLC
CF PTFE
SiC
SiC
SiC+DLC
SiC
SiC
SiC
SiC+DLC
TB-mag A
A TB-mag B
B
C
TB-mag C
Long Coupled B/C
LC
L Secondary Seal Unit B/C
SS
S LC-Standard Long Coupled Bearing Frame for
TB-mag Models B1-C9, $$ Adder
SS-Long Coupled Bearing Frame equipped with
Patented Secondary Sealing System for
TB-mag Models B1-C9, $$$ Adder
Option 1
S
0
1
2
3
Option 2
Impeller
Body
Casing
Casting/Lining
0
- CF-ETFE
D.I./ETFE
- CF-ETFE
D.I./ETFE
1
- CF-ETFE
D.I./Unfilled PFA
C
2
C
3
- CF-ETFE
D.I./Unfilled PFA
- CF-ETFE
D.I./ETFE
C
4
- CF-ETFE
D.I./ETFE
C
5
C - Consult Factory for Availability
S - Standard Material/Options
S
Casing
Drain
Containment Shell
Lining/Composite
Yes
No
Yes
No
Yes
No
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
Impeller
Torque
Standard
Standard
Standard
Standard
Ultra
Ultra
Material Guide
CF - Carbon Fiber
D.I. - Ductile Iron
DLC - Diamond Like Carbon Coating
ETFE - Ethylene-tetrafluoroethylene
PFA - Perfluoroalkoxy
SiC - Silicon Carbide (Ceramic)
Page 13 of 65
Pump
Series
TB-mag A
TB-mag B
TB-mag C
1450
4.1
(3.1)
5.8
(4.4)
8.3
(6.2)
12.5
(9.3)
10.4
(7.7)
20.7
(15.5)
(23.3)
31.3
41.0
(31.0)
Page 14 of 65
Pump Size
(50 x 32 x 160mm)
(65 x 50 x 160mm)
(50 x 32 x 200mm)
(65 x 40 x 200mm)
(100 x 65 x 200mm)
Drive Torque
0,1
0,1
0,1
0,1
0,1
Drive Torque
0
1
2
Motor Frame
NEMA C-Face
A B C ta
D ta
E F -
Impeller Diameter
Bearing System
1
Bushing
SiC
Shaft, Pump
SiC
G
H
tc
J
uc
K
IEC B5
M
N
P
Q
ta
R
S
T
tc
U
tc
V
uc
W
1
2
3
4
Gasket
S
1
2
3
SiC
SiC
SiC
Sintered SiC+DLC
SiC
CF PTFE
SiC
Sintered SiC+DLC
CF PTFE
SiC
SiC
Sintered SiC+DLC
SiC
SiC
SiC
Sintered SiC+DLC
Option 1
S
0
1
2
3
Casing
Casting/Lining
- CF-ETFE
D.I./ETFE
0
- CF-ETFE
D.I./ETFE
1
C
2
- CF-ETFE
D.I./Unfilled PFA
- CF-ETFE
D.I./Unfilled PFA
C
3
- CF-ETFE
D.I./ETFE
C
4
C
5
- CF-ETFE
D.I./ETFE
C - Consult Factory for Availability
S - Standard Material/Options
S
Casing
Drain
Containment Shell
Lining/Composite
Yes
No
Yes
No
Yes
No
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
CF-ETFE/Aramid Composite
(A Series Only)
56C
143/5TC
182/4TC
213/5TC
254/6TC (Max. A-Series)
254/6 (4 Pole)
284/6TSC(Max. B-Series)
324/6TSC
364/365TSC
284/6TC
324/6TC & 405TSC
80
90S/L
100L
112M
132S/M
160M
160M/L
180M/L
200L
225S/M
(A Series Only)
(Max. A-Series)
(Max. B-Series)
Product Group
Option 2
Impeller
Body
Standard Torque
High Torque
Ultra High Torque
* 165
mm, (i.e. - 165, 140)
* Impeller trim for ISO models must be specified in mm.
Impeller
Torque
Standard
Standard
Standard
Standard
Ultra
Ultra
TB-mag A
E TB-mag B
F TB-mag C
G LC
L Long Coupled B/C
Secondary Seal Unit B/C
SS
S LC-Standard Long Coupled Bearing Frame for
TB-mag Models B1-C9, $$ Adder
SS-Long Coupled Bearing Frame equipped with
Patented Secondary Sealing System for
TB-mag Models B1-C9, $$$ Adder
(ANSI DIMENSIONAL BEARING FRAME ONLY)
Material Guide
CF - Carbon Fiber
D.I. - Ductile Iron
DLC - Diamond Like Carbon Coating
ETFE - Ethylene-tetrafluoroethylene
PFA - Perfluoroalkoxy
SiC - Silicon Carbide (Ceramic)
Page 15 of 65
Pump
Series
TB-mag A
TB-mag B
TB-mag C
1450
4.1
(3.1)
5.8
(4.4)
8.3
(6.2)
12.5
(9.3)
(7.7)
10.4
20.7
(15.5)
(23.3)
31.3
41.0
(31.0)
Page 16 of 65
235
232
236
300 6 9b
20 231 19 239 27
Item
Qty
1
2
6
7
8a
8b
9a
9b
9c
14
19
20
27
72
73
231
232
235
236
239
300
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
14
8b 2 9c 9a 7 8a 1
73
14
72
Part Name
Material
Casing
Impeller Magnet Assembly
Shaft, Pump
Wear Ring, Front Stationary
Wear Ring, Front Rotating
Wear Ring, Back Rotating
Retaining Ring, Front Stationary
Retaining Ring, Back Stationary
Retaining Ring, Pin (sets)
Valve, Thrust Control
Adapter
Only for Group 2, TB-mag B/C 8.25 centerline
Wear Ring, Back Stationary
Collar, Thrust
Gasket, O-ring
Shell, Containment
Magnet Assembly, Outer
Bushing, Bearing
Bushing, Spacer
Ring, Containment
Hex Cap Screw/Lock Washer
TB-mag A
TB-mag B/C
N. - 90S/L
P. - 100L
Q. - 112M
R. - 132S/M
R1. - 132S/M, High Torque
S. - 160M
T. - 160M/L
U. - 180M/L
V. - 200L
U. - 180M/L, High Torque
V. - 200L, High Torque
W. - 225S/M, High Torque
ADP-1135-SI
ADP-1145-SI
ADP-1135-SI
ADP-1125-SI
ADP-1125-SI
ADP-1100-SI
ADP-1015-SI
ADP-1010-SI
B. - 143/5TC
C. - 182/4TC
D. - 213/5TC
E. - 254/6TC (2 Pole)
F. - 284/6TSC & 254/6TC
G. - 324/6TSC
H. - 364/365TSC, High Torque
J. - 284/6TC
J1. - 284/6TC, High Torque
K. - 324TC, High Torque
ADP-1100-SI
ADP-1100-SI
MAO-1005-SI
MAO-1015-SI
MAO-1025-SI
MAO-1035-SI
MAO-1036-SI
ADP-1005-SI
M. - 80
N. - 90
P. - 100/112
R. - 132
R1. - 132
MAO-2100-SI
MAO-2110-SI
MAO-2120-SI
MA0-1055-SI
MA0-1065-SI
MA0-1066-SI
MA0-1075-SI
MA0-1076-SI
MA0-1085-SI
MA0-1095-SI
MA0-1105-SI
MA0-1115-SI
MA0-1106-SI
MA0-1116-SI
MA0-1125-SI
MA0-1040-SI
MA0-1050-SI
MA0-1060-SI
MA0-1070-SI
MA0-1080-SI
MA0-1090-SI
MA0-1100-SI
MA0-1110-SI
MA0-1111-SI
MA0-1120-SI
MAO-1000-SI
MAO-1010-SI
MAO-1020-SI
MAO-1030-SI
MAO-1031-SI
MAO-1032-SI
ADP-1000-SI
A. - 56C
B. - 143/5 TC
C. - 182/4 TC
D. - 213/5 TC
E. - 213/5 TC, High Torque
F. - 254/6 TC, High Torque
Adapter
(NEMA/IEC Close Coupled
with Riser)
DRIVE END
Mounting Plate
(Close Coupled
NEMA/IEC)
SLC-1030-AA
SLC-1020-AA
SLC-1010-AA
SLC-1000-AA
IMA-1100-AA
IMA-1100-AA
IMA-1100-AA
IMA-1120-AA
IMA-1130-AA
IMA-1155-AA
IMA-1140-AA
IMA-1150-AA
IMA-1030-AA
IMA-1030-AA
IMA-1030-AA
IMA-1030-AA
IMA-1020-AA
IMA-1040-AA
IMA-1040-AA
IMA-1020-AA
IMA-1065-AA
IMA-1050-AA
IMA-1060-AA
IMA-1060-AA
IMA-1030-AA
IMA-1010-AA
IMA-1010-AA
IMA-1010-AA
IMA-1010-AA
IMA-1070-AA
IMA-1070-AA
IMA-1070-AA
IMA-1010-AA
CSG-1100-AA
CSG-1100-LB
CSG-1110-AA
CSG-1120-AA
CSG-1130-AA
CSG-1155-AA
CSG-1140-AA
CSG-1150-AA
CSG-1030-AA
CSG-1030-LB
CSG-1035-AA
CSG-1035-LB
CSG-1020-AA
CSG-1080-AA
CSG-1085-AA
CSG-1090-AA
CSG-1160-AA
CSG-1050-AA
CSG-1060-AA
CSG-1065-AA
CSG-1230-AA
C3
CL
C4
C5
C6
C9
C7
C8
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
W1
A1
AL
E1
EL
A3
E3
A4
V1
(2 x 1 x 10)
(2 x 1 x 10) Low Flow
(3 x 1.5 x 10)
(3 x 2 x 10)
(4 x 3 x 10)
(6 x 4 x 8)
(4 x 3 x 10H)
(6 x 4 x 10H)
(1.5 x 1 x 8)
(1.5 x 1 x 8) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6) 7" (178mm)
(4 x 3 x 6) 7" (178mm)
(3 x 2 x 8)
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1.5 x 8) Vertical
(1.5 x 1 x 6)
(1.5 x 1 x 6) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(2 x 1.5 x 6) Vertical
Casing Assembly
(Includes: Wear Ring, Thrust Collar)
CSG-1010-AA
CSG-1010-LB
CSG-1015-AA
CSG-1015-LB
CSG-1070-AA
CSG-107A-AA
CSG-1075-AA
CSG-1210-AA
WET END
Containment Shell
Complete
Assembly
Impeller
(Includes:Pump
Assembly
Shaft, Wear Ring & (Includes: Wear
Gasket)
Ring & Bushing)
NOTES:
1. - Metric pump/parts
2. - Not all configurations are listed, consult factory for details.
RGC-1020-SI
RGC-1025-SI
RGC-1010-SI
RGC-1015-SI
RGC-1000-SI
RGC-1005-SI
Containment Ring
6" (152mm)
8" (210mm)
10" (267mm)
Motor Frame
(NEMA/IEC)
Page 17 of 65
Page 18 of 65
TB-mag A
TB-mag B
Model (Size)
A1 - (1.5x1x6)
ANSI Designation - AA
AL - (1.5x1x6 LF)
ANSI Designation - AA
A3 - (3x1.5x6)
ANSI Designation - AB
A4 - (3x2x6)
ANSI Designation - -B1 - (1.5x1x8)
ANSI Designation - AA
BL - (1.5x1x8 LF)
ANSI Designation - AA
B3 - (3x2x6 Short)
ANSI Designation - -B4 - (3x1.5x8)
ANSI Designation - A50
B5 - (3x2x6 Tall)
ANSI Designation - A10
B6 - (4x3x6)
ANSI Designation - --
In (mm)
D
2E1
2E2
lb. (kg)
CP
8.70
(221)
5.25
(133)
6.00
(152)
0.00
0
7.25
(184)
11.75
(298)
SF
DF
Weight
1.50
(38)
1.00
(25)
80.00
(36)
3.00
(76)
6.50
(165)
4.00
(102)
1.50
(38)
1.50
(38)
2.00
(51)
1.00
(25)
11.30
(287)
16.75
(425)
8.25
(210)
9.75
(248)
7.25
(184)
12.50
(318)
16.50
(419)
90.00
(41)
125.00
(57)
135.00
(61)
3.00
(76)
2.00
(51)
153.00
(70)
135.00
(61)
8.50
(216)
4.00
(102)
3.00
(76)
185.00
(84)
Page 19 of 65
Model (Size)
TB-mag C
C1 - (3x2x8)
ANSI Designation - A60
C2 - (4x3x8)
ANSI Designation - A70
C3 - (2x1x10)
ANSI Designation - A05
CL - (2x1x10 LF)
ANSI Designation - A05
C4 - (3x1.5x10)
ANSI Designation - A50
C5 - (3x2x10)
ANSI Designation - A60
C6 - (4x3x10)
ANSI Designation - A70
C7 - (4x3x10H)
ANSI Designation - A70
C8 - (6x4x10H)
ANSI Designation - A80
C9 - (6x4x8)
ANSI Designation - A80
In (mm)
D
8.25
(210)
10.00
(254)
2E1
9.75
(248)
2E2
7.25
(184)
12.50
(318)
17.75
(451)
lb. (kg)
Y
CP
SF
DF
Weight
9.50
(241)
3.00
(76)
2.00
(51)
159.00
(72)
19.25
(489)
11.00
(279)
4.00
(102)
3.00
(76)
195.00
(88)
16.75
(425)
8.50
(216)
2.00
(51)
1.00
(25)
174.00
(79)
3.00
(76)
1.50
(38)
2.00
(51)
17.75
(451)
9.50
(241)
19.25
(489)
11.00
(279)
4.00
(102)
3.00
(76)
3.00
(76)
188.00
(85)
189.00
(86)
205.00
(93)
219.00
(99)
23.50
(597)
13.50
(343)
6.00
(152)
4.00
(102)
269.00
(122)
4.00
(102)
11.30
(287)
NOTE: Dimensions are for reference only, use certified drawings for construction.
Page 20 of 65
in (mm)
Model (Size)
Series
2E1
2E2
M2
lb.
7.25
(184)
11.50
(292)
6.299
(160)
CP
E1 - (50x32x160)
TB-mag A
EL - (50x32x160LF)
5.20
(132)
7.48
(190)
E3 - (65x50x160)
4.33
(110)
F1 - (50x32x200)
TB-mag B
FL - (50x32x200LF)
TB-mag C
G2 - (100x65x200)
9.91
(252)
8.35
(212)
F4 - (65x40x200)
7.09
(180)
9.84
(250)
3.15
(80)
2.76
(70)
6.299
(160)
8.39
(213)
3.74
(95)
13.39
(340)
15.94
(405)
7.09
(180)
8.86
(225)
11.16
(284)
3.97
(100)
SF
DF
(kg)
1.97
(50)
1.26
(32)
80
(36)
2.56
(65)
1.97
(50)
86
(39)
1.97
(50)
1.26
(32)
133
(60)
2.56
(65)
1.57
(40)
144
(65)
3.93
(100)
2.56
(65)
168
(76)
Page 21 of 65
100
2900 rpm
150
200
400
120
350
100
A1-1.5x1x6
300
A1-1.5x1x6 LF
C3
C4
B1-1.5x1x8
C6
60
B1
TDH (m)
TDH (ft)
C5
200
B4
150
40
C6-4x3x10
0
100
C5-3x2x10
20
A3/4
C1-3x2x8
C4-3x1.5x10
B3/5
A1
B4-3x1.5x8
C3-2x1x10
C2
A1
LF
B3/5-3x2x6
C2-4x3x8
C1
100
50
A3/4-3x1.5/2x6
80
250
200
300
400
500
600
700
0
900
800
Capacity (m3/hr)
50
100
150
200
250
1450 rpm
300
100
30
C4
90
A1-1.5x1x6
25
80
A1-1.5x1x6 LF
A3/4-3x1.5/2x6
70
C3
B1-1.5x1x8
20
C5
B3/5-3x2x6
B4-3x1.5x8
C6
50
15
C7
C8
40 B1
B4
10
30
TDH (m)
TDH (ft)
60
C1-3x2x8
C2-4x3x8
C3-2x1x10
C4-3x1.5x10
C5-3x2x10
C2
20
C6-4x3x10
A1
10
C7-4x3x10H
C8-6x4x10H
A1 LF A3/4
0
0
B3/5
200
400
600
800
1000
1200
0
1400
C3
Page 22 of 65
Capacity (m /hr)
50
100
150
200
3500 rpm
250
600
180
160
500
A1-1.5x1x6
140
C3
400
A1-1.5x1x6 LF
A3/4-3x1.5/2x6
120
C4
B1-1.5x1x8
100
300
C6
80
B1
TDH (m)
TDH (ft)
C5
B4
B4-3x1.5x8
C1-3x2x8
C2-4x3x8
200
C1
60
C2
B3/5
100 A1
LF
B3/5-3x2x6
C3-2x1x10
C4-3x1.5x10
40
C5-3x2x10
A1
A3/4
C6-4x3x10
20
0
0
200
400
600
800
1000
1200
Capacity (m /hr)
20
40
60
80
1750 rpm
100
140
C4
40
A1-1.5x1x6
120
35
A1-1.5x1x6 LF
A3/4-3x1.5/2x6
100
C3
30
C5
B1-1.5x1x8
C6
C7
20
C8
60
B4-3x1.5x8
C1-3x2x8
C2-4x3x8
B1
B4 C1
15
C3-2x1x10
C4-3x1.5x10
40
10
C2
A1
200
400
C7-4x3x10H
C8-6x4x10H
A1 LF A3/4 B3/5
0
C5-3x2x10
C6-4x3x10
20
TDH (m)
TDH (ft)
B3/5-3x2x6
25
80
0
600
800
1000
1200
1400
1600
Page 23 of 65
Pump End
TB-mag
Wet End
Standard
Casing:
Internals:
Materials
Pure ETFE
CF-ETFE
Model
Size
Motor Frame
Pump End
Wet End
A1
(1.5x1x6)
A,B,C,D,M,N,P,Q,R
$3,900
$2,900
ANSI - AA
D1,E1,R1
$4,250
AL
(1.5x1x6 LF)
A,B,C,D,M,N,P,Q,R
$3,900
ANSI - AA
D1,E1,R1
$4,250
A3
A4
V1
B1
BL
B
B3
(3x1.5x6)
A,B,C,D,M,N,P,Q,R
$4,500
ANSI - AB
D1,E1,R1
$4,850
(3x2x6)
A,B,C,D,M,N,P,Q,R
$4,500
ANS - --
D1,E1,R1
$4,850
(2x1.5x6)
A,B,C,D,M,N,P,Q,R
$4,500
ANSI - 2015/15
D1,E1,R1
$4,850
(1.5x1x8)
B,C,D,E,N,P,Q,R
$5,200
ANSI - AA
$5,650
F,R1
$5,700
$6,150
(1.5x1x8 LF)
B,C,D,E,N,P,Q,R
$5,200
ANSI - AA
$5,650
F,R1
$5,700
$6,150
(3x2x6 Short)
B,C,D,E,N,P,Q,R
$5,200
ANSI - --
$5,650
F,R1
$5,700
$6,150
$3,500
$3,500
$4,200
Page 24 of 65
TB-mag
Standard
Casing:
Internals:
Materials
Pure ETFE
CF-ETFE
Model
Size
Motor Frame
Pump End
Wet End
B4
(3x1.5x8)
B,C,D,E,N,P,Q,R
$5,300
$4,300
ANSI - A50
B5
B
B6
$5,750
F,R1
$5,800
$6,250
(3x2x6 Tall)
B,C,D,E,N,P,Q,R
$5,200
ANSI - A10
$5,650
F,R1
$5,700
$6,150
B,C,D,E,N,P,Q,R
$6,250
$6,700
F,R1
$6,750
(4x3x6)
ANSI - --
W1
ANSI - 2015/15
C1
C2
(2x1.5x8)
C3
CL
$7,200
$5,800
$6,250
F,R1
$6,300
$6750
(3x2x8)
B,C,D,E,N,P,Q,R
$6,000
ANSI - A60
$6,450
F,J,R1
$6,500
G,T,U,V
$6,950
H1,J1,K1,U1,V1,W1
$7,450
(4x3x8)
B,C,D,E,N,P,Q,R
$7,000
ANSI - A70
$7,450
F,J,R1
$7,500
G,T,U,V
$7,950
H1,J1,K1,U1,V1,W1
$8,450
(2x1x10)
B,C,D,E,N,P,Q,R
$8,000
ANSI - A05
$8,450
F,J,R1
$8,500
(2x1x10 LF)
ANSI - A05
T
B,C,D,E,N,P,Q,R
G,T,U,V
$8,950
H1,J1,K1,U1,V1,W1
$9,450
B,C,D,E,N,P,Q,R
$8,000
$8,450
F,J,R1
$8,500
G,T,U,V
$8,950
H1,J1,K1,U1,V1,W1
$9,450
$4,200
$5,250
$4,800
$5,000
$6,000
$7,000
Page 25 of 65
TB-mag
Size
Motor Frame
Pump End
Wet End
C4
(3x1.5x10)
B,C,D,E,N,P,Q,R
$8,500
$7,500
C5
(3x2x10)
ANSI - A60
C6
C7
C9
$8,950
F,J,R1
$9,000
G,T,U,V
$9,450
H1,J1,K1,U1,V1,W1
$9,950
B,C,D,E,N,P,Q,R
$9,000
$9,450
F,J,R1
$9,500
G,T,U,V
$9,950
H1,J1,K1,U1,V1,W1
$10,450
(4x3x10)
B,C,D,E,N,P,Q,R
$9,500
ANSI - A70
$9,950
(4x3x10H)
ANSI - A70
C8
Materials
Pure ETFE
CF-ETFE
Model
ANSI - A50
Standard
Casing:
Internals:
$8,000
$8,500
F,J,R1
$10,000
G,T,U,V
$10,450
H1,J1,K1,U1,V1,W1
$10,950
K2, W2
$11,950
$9,000
B,C,D,E,N,P,Q,R
$9,500
$8,500
$9,950
F,J,R1
$10,000
G,T,U,V
$10,450
H1,J1,K1,U1,V1,W1
$10,950
K2, W2
$11,950
$9,000
$9,500
(6x4x10H)
B,C,D,E,N,P,Q,R
$10,500
ANSI - A80
$10,950
F,J,R1
$11,000
G,T,U,V
$11,450
H1,J1,K1,U1,V1,W1
$11,950
K2, W2
$12,950
$10,000
$10,750
(6x4x8)
B,C,D,E,N,P,Q,R
$11,750
ANSI - A80
$12,200
F,J,R1
$12,250
G,T,U,V
$12,700
H1,J1,K1,U1,V1,W1
$13,200
K2, W2
$14,200
$11,250
Page 26 of 65
Model
TB
Size/Description
B/C Series Adapter and Bearing unit , Outer Magnet Assembly
B/C Series Adapter and Bearing unit, Secondary Seal Package, Outer Magnet Assembly
Part #
BFR-2000-AA
BFR-2050-AA
$/Each
$1,500.00
$7,500.00
Model
TB
Size/Description
A/B/C Series, Premium, low friction DLC coating on SiC Bushings and Pump Shaft
A/B/C Series, Premium, low friction DLC coating on SiC Wear Rings
$/Each
$250.00
$350.00
Page 27 of 65
Wet End
Pump End
TB-mag
Model
E1
Size
Motor Frame
Standard
Casing:
Internals:
Pump End
(50 x 32 x 160mm)
A,B,C,D,M,N,P,Q,R
$3,900
D1,E1,R1
$4,250
A,B,C,D,M,N,P,Q,R
$4,500
D1,E1,R1
$4,850
B,C,D,E,N,P,Q,R
$5,200
$5,650
F,R1
$5,700
$6,150
B,C,D,E,N,P,Q,R
$5,300
$5,750
F,R1
$5,800
$6,250
B,C,D,E,N,P,Q,R
$7,000
$7,450
F,J,R1
$7,500
G,T,U,V
$7,950
H1,J1,K1,U1,V1,W1
$8,450
A
E3
F1
(65 x 50 x 160mm)
(50 x 32 x 200mm)
F4
G2
C
(65 x 40 x 200mm)
(100 x 65 x 200mm)
Material
Pure ETFE
CF-ETFE
Wet End
$2,900
$3,500
$4,200
$4,300
$6,000
Page 28 of 65
Model
TB
Size/Description
B/C Series Adapter and Bearing unit , Outer Magnet Assembly
B/C Series Adapter and Bearing unit, Secondary Seal Package, Outer Magnet Assembly
Part #
BFR-2000-AA
BFR-2050-AA
$/Each
$1,500.00
$7,500.00
Model
TB
Size/Description
A/B/C Series, Premium, low friction DLC coating on SiC Bushings and Pump Shaft
A/B/C Series, Premium, low friction DLC coating on SiC Wear Rings
$/Each
$250.00
$350.00
Page 29 of 65
1
1.
2.
3.
4.
Qty: 1
Part Name:
Casing, Lined
One piece cast ductile iron.
Bonded ETFE or PFA lining, minimum of 1/8 (3mm) thickness.
Self venting, top centerline discharge design.
Two bolt flanged drain with pure PTFE gasket and 316SS blind flange, standard.
Plastic Lining,
No Wear Rings.
Standard
Flanged Drain
Model
A1
AL
E1
EL
A3
E3
A4
Standard
Casing Lining:
ETFE
Optional 1
Casing Lining:
PFA
Part #
$/Each
Part #
$/Each
CSG-1010-SI
CSG-1011-SI
CSG-1012-SI
CSG-1013-SI
CSG-1010-LF
CSG-1011-LF
CSG-1012-LF
CSG-1013-LF
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
CSG-1010-PI
CSG-1011-PI
CSG-1012-PI
CSG-1013-PI
CSG-1010-PF
CSG-1011-PF
CSG-1012-PF
CSG-1013-PF
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
50 x 32mm - ISO PN 16
CSG-1015-SI
$956.00
CSG-1015-PI
$1,912.00
CSG-1017-SI
$956.00
CSG-1017-PI
$1,912.00
CSG-1018-SI
$956.00
CSG-1018-PI
$1,912.00
50 x 32mm - ISO PN 16
CSG-1015-LF
$956.00
CSG-1015-PF
$1,912.00
CSG-1017-LF
$956.00
CSG-1017-PF
$1,912.00
CSG-1018-LF
$956.00
CSG-1018-PF
$1,912.00
CSG-1070-SI
$956.00
CSG-1070-PI
$1,912.00
CSG-1071-SI
CSG-1072-SI
CSG-1073-SI
CSG-1074-SI
CSG-107A-SI
CSG-107B-SI
CSG-107C-SI
CSG-107D-SI
CSG-1075-SI
CSG-1076-SI
CSG-1077-SI
CSG-1078-SI
CSG-1079-SI
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
$956.00
CSG-1071-PI
CSG-1072-PI
CSG-1073-PI
CSG-1074-PI
CSG-107A-PI
CSG-107B-PI
CSG-107C-PI
CSG-107D-PI
CSG-1075-PI
CSG-1076-PI
CSG-1077-PI
CSG-1078-PI
CSG-1079-PI
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
$1,912.00
Size/Description
1.5 x 1 - ANSI class 150
1.5 x 1 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
1.5 x 1 - ANSI class 150
1.5 x 1 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
Page 30 of 65
Model
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
Size/Description
1.5 x 1 - ANSI class 150
1.5 x 1 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
1.5 x 1 - ANSI class 150
1.5 x 1 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
50 x 32mm - ISO PN 16
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
2.0 x 1.5 - ANSI class 150
50 x 32mm - ISO PN 16
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
2.0 x 1.5 - ANSI class 150
3 x 2 - ANSI class 150
3 x 2 - ANSI class 300
80 x 50mm - ISO PN 16
80 x 65mm - JIS 10 kg/cm^2
3 x 1.5 - ANSI class 150
3 x 1.5 - ANSI class 300
65 x 40mm - ISO PN 16
65 x 50mm - ISO PN 16
65 x 50mm - JIS 10 kg/cm^2
65 x 40mm - ISO PN 16
65 x 50mm - JIS 10 kg/cm^2
3 x 1.5 - ANSI class 150
3x2 (A10) - ANSI class 150
3x2 (A10) - ANSI class 300
80 x 50mm - ISO PN 16
80 x 65mm - ISO PN 16
80 x 65mm - JIS 10 kg/cm^2
4x3 - ANSI class 150
4x3 - ANSI class 300
100 x 65mm - ISO PN 16
100 x 80mm - ISO PN 16
100 x 80mm - JIS 10 kg/cm^2
3 x 2 - ANSI class 150
3 x 2 - ANSI class 300
80 x 50mm - ISO PN 16
80 x 65mm - JIS 10 kg/cm^2
4 x 3 - ANSI class 150
4 x 3 - ANSI class 300
100 x 65mm - ISO PN 16
100 x 80mm - JIS 10 kg/cm^2
100 x 65mm - ISO PN 16
100 x 80mm - JIS 10 kg/cm^2
4 x 3 - ANSI class 150
Standard
Casing Lining:
Part #
CSG-1030-SI
CSG-1031-SI
CSG-1032-SI
CSG-1033-SI
CSG-1030-LF
CSG-1031-LF
CSG-1032-LF
CSG-1033-LF
CSG-1035-SI
CSG-1036-SI
CSG-1037-SI
CSG-1038-SI
CSG-1035-LF
CSG-1036-LF
CSG-1037-LF
CSG-1038-LF
CSG-1020-SI
CSG-1021-SI
CSG-1022-SI
CSG-1023-SI
CSG-1080-SI
CSG-1081-SI
CSG-1082-SI
CSG-1083-SI
CSG-1084-SI
CSG-1085-SI
CSG-1087-SI
CSG-1088-SI
CSG-1090-SI
CSG-1091-SI
CSG-1092-SI
CSG-1093-SI
CSG-1094-SI
CSG-1160-SI
CSG-1161-SI
CSG-1162-SI
CSG-1163-SI
CSG-1164-SI
CSG-1050-SI
CSG-1051-SI
CSG-1052-SI
CSG-1053-SI
CSG-1060-SI
CSG-1061-SI
CSG-1062-SI
CSG-1063-SI
CSG-1065-SI
CSG-1067-SI
CSG-1068-SI
ETFE
$/Each
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,850.00
$1,850.00
$1,850.00
$1,850.00
$1,850.00
$1,850.00
$1,850.00
$1,850.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$1,625.00
$2,400.00
$2,400.00
$2,400.00
$2,400.00
$2,400.00
$2,100.00
$2,100.00
$2,100.00
$2,100.00
$2,400.00
$2,400.00
$2,400.00
$2,400.00
$2,400.00
$2,400.00
$2,400.00
Optional 1
Casing Lining:
Part #
CSG-1030-PI
CSG-1031-PI
CSG-1032-PI
CSG-1033-PI
CSG-1030-PI
CSG-1031-PI
CSG-1032-PI
CSG-1033-PI
CSG-1035-PI
CSG-1036-PI
CSG-1037-PI
CSG-1038-PI
CSG-1035-PF
CSG-1036-PF
CSG-1037-PF
CSG-1038-PF
CSG-1020-PI
CSG-1021-PI
CSG-1022-PI
CSG-1023-PI
CSG-1080-PI
CSG-1081-PI
CSG-1082-PI
CSG-1083-PI
CSG-1084-PI
CSG-1085-PI
CSG-1087-PI
CSG-1088-PI
CSG-1090-PI
CSG-1091-PI
CSG-1092-PI
CSG-1093-PI
CSG-1094-PI
CSG-1160-PI
CSG-1161-PI
CSG-1162-PI
CSG-1163-PI
CSG-1164-PI
CSG-1050-PI
CSG-1051-PI
CSG-1052-PI
CSG-1053-PI
CSG-1060-PI
CSG-1061-PI
CSG-1062-PI
CSG-1063-PI
CSG-1065-PI
CSG-1067-PI
CSG-1068-PI
PFA
$/Each
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,700.00
$3,700.00
$3,700.00
$3,700.00
$3,700.00
$3,700.00
$3,700.00
$3,700.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$3,250.00
$4,800.00
$4,800.00
$4,800.00
$4,800.00
$4,800.00
$4,200.00
$4,200.00
$4,200.00
$4,200.00
$4,800.00
$4,800.00
$4,800.00
$4,800.00
$4,800.00
$4,800.00
$4,800.00
Page 31 of 65
Model
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
Size/Description
2x1 - ANSI class 150
2x1 - ANSI class 300
50 x 32mm - ISO PN 16
2x1 - ANSI class 150
2x1 - ANSI class 300
50 x 32mm - ISO PN 16
3x1.5 - ANSI class 150
3x1.5 - ANSI class 300
Standard
Casing Lining:
Part #
CSG-1100-SI
CSG-1101-SI
CSG-1102-SI
CSG-1100-LF
CSG-1101-LF
CSG-1102-LF
CSG-1110-SI
CSG-1111-SI
ETFE
$/Each
$2,100.00
$2,100.00
$2,100.00
$2,100.00
$2,100.00
$2,100.00
$2,100.00
$2,100.00
Optional 1
Casing Lining:
Part #
CSG-1100-PI
CSG-1101-PI
CSG-1102-PI
CSG-1100-PF
CSG-1101-PF
CSG-1102-PF
CSG-1110-PI
CSG-1111-PI
PFA
$/Each
$4,200.00
$4,200.00
$4,200.00
$4,200.00
$4,200.00
$4,200.00
$4,200.00
$4,200.00
65 x 40mm - ISO PN 16
CSG-1112-SI
$2,100.00
CSG-1112-PI
$4,200.00
65 x 50mm - ISO PN 16
CSG-1113-SI
$2,100.00
CSG-1113-PI
$4,200.00
CSG-1114-SI
$2,100.00
CSG-1114-PI
$4,200.00
CSG-1120-SI
$2,690.00
CSG-1120-PI
$5,380.00
CSG-1121-SI
$2,690.00
CSG-1121-PI
$5,380.00
80 x 50mm - ISO PN 16
CSG-1122-SI
$2,690.00
CSG-1122-PI
$5,380.00
80 x 65mm - ISO PN 16
CSG-1123-SI
$2,690.00
CSG-1123-PI
$5,380.00
CSG-1124-SI
$2,690.00
CSG-1124-PI
$5,380.00
CSG-1130-SI
$2,870.00
CSG-1130-PI
$5,740.00
CSG-1131-SI
$2,870.00
CSG-1131-PI
$5,740.00
CSG-1132-SI
$2,870.00
CSG-1132-PI
$5,740.00
CSG-1133-SI
$2,870.00
CSG-1133-PI
$5,740.00
CSG-1134-SI
$2,870.00
CSG-1134-PI
$5,740.00
CSG-1140-SI
$2,950.00
CSG-1140-PI
$5,900.00
CSG-1141-SI
$2,950.00
CSG-1141-PI
$5,900.00
CSG-1142-SI
$2,950.00
CSG-1142-PI
$5,900.00
CSG-1143-SI
$2,950.00
CSG-1143-PI
$5,900.00
CSG-1144-SI
$2,950.00
CSG-1144-PI
$5,900.00
CSG-1150-SI
CSG-1151-SI
CSG-1152-SI
CSG-1153-SI
CSG-1154-SI
CSG-1170-SI
CSG-1171-SI
CSG-1172-SI
CSG-1173-SI
CSG-1174-SI
CSG-1210-SI
CSG-1211-SI
CSG-1212-SI
CSG-1213-SI
CSG-1230-SI
CSG-1231-SI
CSG-1232-SI
CSG-1233-SI
$3,290.00
$3,290.00
$3,290.00
$3,290.00
$3,290.00
$3,400.00
$3,400.00
$3,400.00
$3,400.00
$3,400.00
$2,125.00
$2,125.00
$2,125.00
$2,125.00
$2,225.00
$2,225.00
$2,225.00
$2,225.00
CSG-1150-PI
CSG-1151-PI
CSG-1152-PI
CSG-1153-PI
CSG-1154-PI
CSG-1170-PI
CSG-1171-PI
CSG-1172-PI
CSG-1173-PI
CSG-1174-PI
CSG-1210-PI
CSG-1211-PI
CSG-1212-PI
CSG-1213-PI
CSG-1230-PI
CSG-1231-PI
CSG-1232-PI
CSG-1233-PI
$6,580.00
$6,580.00
$6,580.00
$6,580.00
$6,580.00
$6,800.00
$6,800.00
$6,800.00
$6,800.00
$6,800.00
$3,750.00
$3,750.00
$3,750.00
$3,750.00
$3,850.00
$3,850.00
$3,850.00
$3,850.00
Page 32 of 65
2
1.
2.
3.
4.
Qty: 1
Part Name:
Impeller Magnet
Molded one-piece enclosed impeller made of carbon fiber-reinforced ETFE or PFA.
High strength neodymium iron boron magnet assembly.
Magnet assembly hermetically sealed by Patented Tru-Seal Design.
High efficiency, low NPSHr impeller geometry.
Model
A1
AL
E1
EL
A3
E3
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
Size/Description
(1.5 x 1 x 6)
(1.5 x 1 x 6) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(1.5 x 1 x 8)
(1.5 x 1 x 8) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6)
(4 x 3 x 6)
(3 x 2 x 8)
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1 x 10)
(2 x 1 x 10) Low Flow
(3 x 1.5 x 10)
(3 x 2 x 10)
(4 x 3 x 10)
(4 x 3 x 10) Ultra High Torque
(4 x 3 x 10H)
(4 x 3 x 10H) Ultra High Torque
(6 x 4 x 10H)
(6 x 4 x 10H) Ultra High Torque
(6 x 4 x 8)
(6 x 4 x 8) Ultra High Torque
(2 x 1.5 x 6) Vertical
(2 x 1.5 x 8) Vertical
Standard
Impeller:
Part #
IMA -1010-SI
IMA -1010-SI
IMA -1010-SI
IMA -1010-SI
IMA -1070-SI
IMA -1070-SI
IMA -1070-SI
IMA -1030-SI
IMA -1030-SI
IMA -1030-SI
IMA -1030-SI
IMA -1020-SI
IMA -1040-SI
IMA -1040-SI
IMA -1020-SI
IMA -1160-SI
IMA -1050-SI
IMA -1060-SI
IMA -1060-SI
IMA -1100-SI
IMA -1100-SI
IMA -1100-SI
IMA -1120-SI
IMA -1130-SI
IMA -1132-SI
IMA -1140-SI
IMA -1142-SI
IMA -1150-SI
IMA -1152-SI
IMA -1155-SI
IMA -1157-SI
IMA -1010-SI
IMA -1030-SI
CF/ETFE
$/Each
$902.00
$902.00
$902.00
$902.00
$902.00
$902.00
$902.00
$1,600.00
$1,600.00
$1,600.00
$1,600.00
$1,500.00
$1,600.00
$1,600.00
$1,500.00
$1,900.00
$1,900.00
$2,100.00
$2,100.00
$2,000.00
$2,000.00
$2,000.00
$2,200.00
$2,300.00
$2,950.00
$2,550.00
$3,200.00
$2,700.00
$3,350.00
$2,900.00
$3,550.00
$902.00
$1,600.00
Option 1
Impeller:
Part #
IMA -1010-PI
IMA -1010-PI
IMA -1010-PI
IMA -1010-PI
IMA -1070-PI
IMA -1070-PI
IMA -1070-PI
IMA -1030-PI
IMA -1030-PI
IMA -1030-PI
IMA -1030-PI
IMA -1020-PI
IMA -1040-PI
IMA -1040-PI
IMA -1020-PI
IMA -1160-PI
IMA -1050-PI
IMA -1060-PI
IMA -1060-PI
IMA -1100-PI
IMA -1100-PI
IMA -1100-PI
IMA -1120-PI
IMA -1130-PI
CF/PFA
$/Each
$1,353.00
$1,353.00
$1,353.00
$1,353.00
$1,353.00
$1,353.00
$1,353.00
$2,400.00
$2,400.00
$2,400.00
$2,400.00
$2,250.00
$2,400.00
$2,400.00
$2,250.00
$2,850.00
$2,850.00
$3,150.00
$3,150.00
$3,000.00
$3,000.00
$3,000.00
$3,300.00
$3,450.00
IMA -1140-PI
$3,825.00
IMA -1150-PI
$4,050.00
IMA -1170-PI
$4,050.00
IMA -1010-PI
IMA -1010-PI
$1,353.00
$1,353.00
Page 33 of 65
6
1.
2.
3.
Qty: 1
Part Name:
Shaft, Pump
Replaceable, straight SiC shaft.
Cantilevered design leaves impeller eye open for optimum NPSHr.
Shaft oversized to handle any combinations of radial loads.
Model
TB
Item:
Detail:
7
A.
B.
Size/Description
A-Series - O.D. = 1.00" (Before 9-1-2007)
A-Series - O.D. = 1.00" (Current)
B/C-Series - O.D. = 1.50" (Before 9-1-2007)
B/C-Series - O.D. = 1.50" (Current)
Standard
Material:
Part #
STP-1000-SI
STP-1005-SI
STP-1010-SI
STP-1015-SI
SiC
$/Each
$477.00
$477.00
$595.00
$595.00
Option 1
Material:
Part #
STP-1000-DC
SiC + DLC
$/Each
$627.00
STP-1010-DC
$745.00
Qty: 1
Part Name:
Wear Ring, Front Stationary
Replaceable, Sintered SiC or Carbon Filled PTFE
Positioned in the casing suction.
Model
A1
AL
E1
EL
A3
E3
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
Size/Description
(1.5 x 1 x 6)
(1.5 x 1 x 6) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(1.5 x 1 x 8)
(1.5 x 1 x 8) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6)
(4 x 3 x 6)
OD
3.396
3.396
3.396
3.396
3.765
3.765
3.765
3.396
3.396
3.396
3.396
4.296
4.296
4.296
4.296
5.151
ID
2.645
2.645
2.645
2.645
3.015
3.015
3.015
2.645
2.645
2.645
2.645
3.545
3.545
3.545
3.545
4.201
Standard
Material:
Part #
WRS-1010-SI
WRS-1010-SI
WRS-1010-SI
WRS-1010-SI
WRS-1050-SI
WRS-1050-SI
WRS-1050-SI
WRS-1010-SI
WRS-1010-SI
WRS-1010-SI
WRS-1010-SI
WRS-1020-SI
WRS-1020-SI
WRS-1020-SI
WRS-1020-SI
WRS-1030-SI
C1
(3 x 2 x 8)
4.296
3.545
WRS-1020-SI
SiC
$/Each
$250.00
$250.00
$250.00
$250.00
$272.00
$272.00
$272.00
$250.00
$250.00
$250.00
$250.00
$294.00
$294.00
$294.00
$294.00
$507.00
Option 1
Material::
Part #
WRS-1014-SI
WRS-1014-SI
WRS-1014-SI
WRS-1014-SI
WRS-1054-SI
WRS-1054-SI
WRS-1054-SI
WRS-1014-SI
WRS-1014-SI
WRS-1014-SI
WRS-1014-SI
WRS-1024-SI
WRS-1024-SI
WRS-1024-SI
WRS-1024-SI
WRS-1034-SI
CFR/PTFE
$/Each
$100.00
$100.00
$100.00
$100.00
$108.00
$108.00
$108.00
$100.00
$100.00
$100.00
$100.00
$118.00
$118.00
$118.00
$118.00
$203.00
Option 2
Material::
Part #
WRS-1010-DC
WRS-1010-DC
WRS-1010-DC
WRS-1010-DC
WRS-1050-DC
WRS-1050-DC
WRS-1050-DC
WRS-1010-DC
WRS-1010-DC
WRS-1010-DC
WRS-1010-DC
WRS-1020-DC
WRS-1020-DC
WRS-1020-DC
WRS-1020-DC
WRS-1030-DC
SiC + DLC
$/Each
$400.00
$400.00
$400.00
$400.00
$422.00
$422.00
$422.00
$400.00
$400.00
$400.00
$400.00
$444.00
$444.00
$444.00
$444.00
$657.00
$294.00
WRS-1024-SI
$117.60
WRS-1020-DC
$444.00
Page 34 of 65
Model
C2
G2
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
Item:
Detail:
Size/Description
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1 x 10)
(2 x 1 x 10) Low Flow
(3 x 1.5 x 10)
(3 x 2 x 10)
(4 x 3 x 10)
(4 x 3 x 10H)
(6 x 4 x 10H)
(6 x 4 x 8)
(2 x 1.5 x 6) Vertical
(2 x 1.5 x 8) Vertical
8a
A.
B.
OD
5.151
5.151
3.765
3.765
3.765
4.296
5.151
5.989
7.422
ID
4.201
4.201
3.015
3.015
3.015
3.545
4.201
5.039
6.400
Standard
Material:
Part #
WRS-1030-SI
WRS-1030-SI
WRS-1050-SI
WRS-1050-SI
WRS-1050-SI
WRS-1020-SI
WRS-1030-SI
WRS-1040-SI
WRS-1060-SI
3.396
3.396
2.645
2.645
WRS-1010-SI
WRS-1010-SI
SiC
$/Each
$507.00
$507.00
$272.00
$272.00
$272.00
$294.00
$507.00
$587.00
$870.00
Option 1
Material::
Part #
WRS-1034-SI
WRS-1034-SI
WRS-1054-SI
WRS-1054-SI
WRS-1054-SI
WRS-1024-SI
WRS-1034-SI
WRS-1044-SI
WRS-1064-SI
CFR/PTFE
$/Each
$203.00
$203.00
$108.00
$108.00
$108.00
$118.00
$203.00
$235.00
$348.00
$250.00
$250.00
WRS-1014-SI
WRS-1014-SI
$100.00
$100.00
Option 2
Material::
Part #
WRS-1030-DC
WRS-1030-DC
WRS-1050-DC
WRS-1050-DC
WRS-1050-DC
WRS-1020-DC
WRS-1030-DC
WRS-1040-DC
WRS-1060-DC
SiC + DLC
$/Each
$657.00
$657.00
$422.00
$422.00
$422.00
$444.00
$657.00
$737.00
$1,020.00
WRS-1010-DC
$400.00
Qty: 1
Part Name:
Wear Ring, Front Rotating
Replaceable, Sintered SiC
Located on the impeller front shroud.
Model
A1
AL
E1
EL
A3
E3
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
C3
CL
C4
C5
Size/Description
(1.5 x 1 x 6)
(1.5 x 1 x 6) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(1.5 x 1 x 8)
(1.5 x 1 x 8) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6)
(4 x 3 x 6)
(3 x 2 x 8)
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1 x 10)
(2 x 1 x 10) Low Flow
(3 x 1.5 x 10)
(3 x 2 x 10)
OD
2.640
2.640
2.640
2.640
3.010
3.010
3.010
2.640
2.640
2.640
2.640
3.540
3.540
3.540
3.540
4.196
4.196
4.196
4.196
3.010
3.010
3.010
3.540
ID
2.140
2.140
2.140
2.140
2.510
2.510
2.510
2.140
2.140
2.140
2.140
3.040
3.040
3.040
3.040
3.696
3.696
3.696
3.696
2.510
2.510
2.510
3.040
Standard
Material:
Part #
WRR-1010-SI
WRR-1010-SI
WRR-1010-SI
WRR-1010-SI
WRR-1050-SI
WRR-1050-SI
WRR-1050-SI
WRR-1010-SI
WRR-1010-SI
WRR-1010-SI
WRR-1010-SI
WRR-1020-SI
WRR-1020-SI
WRR-1020-SI
WRR-1020-SI
WRR-1030-SI
WRR-1020-SI
WRR-1030-SI
WRR-1030-SI
WRR-1050-SI
WRR-1050-SI
WRR-1050-SI
WRR-1020-SI
SiC
$/Each
$311.00
$311.00
$311.00
$311.00
$328.00
$328.00
$328.00
$311.00
$311.00
$311.00
$311.00
$342.00
$342.00
$342.00
$342.00
$468.00
$468.00
$468.00
$468.00
$328.00
$328.00
$328.00
$342.00
Option 1
Material::
Part #
WRR-1010-DC
WRR-1010-DC
WRR-1010-DC
WRR-1010-DC
WRR-1050-DC
WRR-1050-DC
WRR-1050-DC
WRR-1010-DC
WRR-1010-DC
WRR-1010-DC
WRR-1010-DC
WRR-1020-DC
WRR-1020-DC
WRR-1020-DC
WRR-1020-DC
WRR-1030-DC
WRR-1020-DC
WRR-1030-DC
WRR-1030-DC
WRR-1050-DC
WRR-1050-DC
WRR-1050-DC
WRR-1020-DC
SiC + DLC
$/Each
$461.00
$461.00
$461.00
$461.00
$478.00
$478.00
$478.00
$461.00
$461.00
$461.00
$461.00
$492.00
$492.00
$492.00
$492.00
$618.00
$618.00
$618.00
$618.00
$478.00
$478.00
$478.00
$492.00
Page 35 of 65
Model
C6
C7
C8
C9
V1
W1
Item:
Detail:
8b
A.
B.
Size/Description
(4 x 3 x 10)
(4 x 3 x 10H)
(6 x 4 x 10H)
(6 x 4 x 8)
(2 x 1.5 x 6) Vertical
(2 x 1.5 x 8) Vertical
OD
4.196
5.034
6.395
5.034
2.640
2.640
ID
3.696
4.440
5.790
4.440
2.140
2.140
Standard
Material:
Part #
WRR-1030-SI
WRR-1040-SI
WRR-1060-SI
WRR-1048-SI
WRR-1010-SI
WRR-1010-SI
Option 1
Material::
Part #
WRR-1030-DC
WRR-1040-DC
WRR-1060-DC
WRR-1048-DC
WRR-1010-DC
SiC + DLC
$/Each
$618.00
$737.00
$1,066.00
$750.00
$461.00
Qty: 1
Part Name:
Wear Ring, Back Rotating
Replaceable, Sintered SiC
Located on the impeller back shroud.
Standard
Model
A1
AL
E1
EL
A3
E3
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
SiC
$/Each
$468.00
$587.00
$916.00
$600.00
$311.00
$311.00
Size/Description
(1.5 x 1 x 6)
(1.5 x 1 x 6) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(1.5 x 1 x 8)
(1.5 x 1 x 8) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6)
(4 x 3 x 6)
(3 x 2 x 8)
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1 x 10)
(2 x 1 x 10) Low Flow
(3 x 1.5 x 10)
(3 x 2 x 10)
(4 x 3 x 10)
(4 x 3 x 10H)
(6 x 4 x 10H)
(6 x 4 x 8)
(2 x 1.5 x 6) Vertical
(2 x 1.5 x 8) Vertical
OD
3.540
3.540
3.540
3.540
3.540
3.540
3.540
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
5.034
7.520
7.520
5.034
3.540
5.034
ID
3.040
3.040
3.040
3.040
3.040
3.040
3.040
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
4.440
6.920
6.920
4.440
3.040
4.440
Option 1
Material:
SiC
Part #
WRR-1020-SI
WRR-1020-SI
WRR-1020-SI
WRR-1020-SI
WRR-1020-SI
WRR-1020-SI
WRR-1020-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1040-SI
WRR-1070-SI
WRR-1070-SI
WRR-1048-SI
WRR-1020-SI
WRR-1040-SI
$/Each
$342.00
$342.00
$342.00
$342.00
$342.00
$342.00
$342.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$972.00
$972.00
$587.00
$342.00
$587.00
Material:
WRR-1049-SI
Option 2
CFPTFE
$372.00
SiC
Material::
$/Each
$342.00
$342.00
$342.00
$342.00
$342.00
$342.00
$342.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$972.00
$972.00
$587.00
$342.00
$587.00
Part #
WRR-1020-DC
WRR-1020-DC
WRR-1020-DC
WRR-1020-DC
WRR-1020-DC
WRR-1020-DC
WRR-1020-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1040-DC
WRR-1070-DC
WRR-1070-DC
WRR-1048-DC
WRR-1020-DC
SiC +
DLC
$/Each
$492.00
$492.00
$492.00
$492.00
$492.00
$492.00
$492.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$1,122.00
$1,122.00
$737.00
$492.00
Page 36 of 65
9a
A.
B.
C.
Qty: 1
Part Name:
Retaining Ring, Front Stationary
Replaceable, Carbon Filled ETFE or PFA
Locks the Front Stationary Wear Ring in the Casing.
Includes proper number of drive keys per pump size.
Model
A1
AL
E1
EL
A3
E3
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
Size/Description
(1.5 x 1 x 6)
(1.5 x 1 x 6) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(1.5 x 1 x 8)
(1.5 x 1 x 8) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6)
(4 x 3 x 6)
(3 x 2 x 8)
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1 x 10)
(2 x 1 x 10) Low Flow
(3 x 1.5 x 10)
(3 x 2 x 10)
(4 x 3 x 10)
(4 x 3 x 10H)
(6 x 4 x 10H)
(6 x 4 x 8)
(2 x 1.5 x 6) Vertical
(2 x 1.5 x 8) Vertical
Standard
Material:
Part #
RGR-1010-AA
RGR-1010-AA
RGR-1010-AA
RGR-1010-AA
RGR-1050-AA
RGR-1050-AA
RGR-1050-AA
RGR-1010-AA
RGR-1010-AA
RGR-1010-AA
RGR-1010-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1030-AA
RGR-1020-AA
RGR-1030-AA
RGR-1030-AA
RGR-1050-AA
RGR-1050-AA
RGR-1050-AA
RGR-1020-AA
RGR-1030-AA
RGR-1040-AA
RGR-1060-AA
RGR-1040-AA
RGR-1010-AA
RGR-1010-AA
CF-ETFE
$/Each
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
Option 1
Material::
Part #
RGR-1010-PA
RGR-1010- PA
RGR-1010- PA
RGR-1010- PA
RGR-1050- PA
RGR-1050- PA
RGR-1050- PA
RGR-1010- PA
RGR-1010- PA
RGR-1010- PA
RGR-1010- PA
RGR-1020- PA
RGR-1020- PA
RGR-1020- PA
RGR-1020- PA
RGR-1030- PA
RGR-1020- PA
RGR-1030- PA
RGR-1030- PA
RGR-1050- PA
RGR-1050- PA
RGR-1050- PA
RGR-1020- PA
RGR-1030- PA
RGR-1040- PA
RGR-1060- PA
RGR-1040- PA
RGR-1010- PA
CF-PFA
$/Each
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
Page 37 of 65
9b
A.
B.
C.
Qty: 1
Part Name:
Retaining Ring, Back Stationary
Replaceable, Carbon Filled ETFE or PFA
Locks the Back Stationary Wear Ring in the Containment Shell
Includes proper number of drive keys per pump size.
Model
A1
AL
E1
EL
A3
E3
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
Size/Description
(1.5 x 1 x 6)
(1.5 x 1 x 6) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(1.5 x 1 x 8)
(1.5 x 1 x 8) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6)
(4 x 3 x 6)
(3 x 2 x 8)
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1 x 10)
(2 x 1 x 10) Low Flow
(3 x 1.5 x 10)
(3 x 2 x 10)
(4 x 3 x 10)
(4 x 3 x 10H)
(6 x 4 x 10H)
(6 x 4 x 8)
(2 x 1.5 x 6) Vertical
(2 x 1.5 x 8) Vertical
Standard
Material:
Part #
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1060-AA
RGR-1060-AA
RGR-1040-AA
RGR-1020-AA
RGR-1020-AA
CF-ETFE
$/Each
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
$15.00
Option 1
Material::
Part #
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1020-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1040-AA
RGR-1060-AA
RGR-1060-AA
RGR-1040-AA
RGR-1020-AA
CF-PFA
$/Each
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
$20.00
Page 38 of 65
9c
A.
B.
Model
TB
Item:
Detail:
9d
A.
B.
TB
Detail:
14
A.
B.
Option 1
Material::
Part #
RGR-1200-PI
CF-PFA
$/Each
$10.00
Option 1
Material::
Part #
RGR-1205-PI
RGR-1206-PI
CF-PFA
$/Each
$10.00
$10.00
Model
Item:
Size/Description
A/B/C
Standard
Material:
CF-ETFE
Part #
$/Each
RGR-1200-SI
$5.00
Size/Description
A/B/C (0.313" Wide)
C-H (0.438" Wide)
Standard
Material:
Part #
RGR-1205-SI
RGR-1206-SI
CF-ETFE
$/Each
$5.00
$5.00
Model
TB
Size/Description
A
B/C
Standard
Material:
Part #
VTC-1000-SI
VTC-1010-SI
SiC
$/Each
$128.00
$151.00
Option 1
Material::
Part #
VTC-1000-DC
VTC-1010-DC
SiC + DLC
$/Each
$278.00
$301.00
Page 39 of 65
19
Detail:
A.
B.
C.
D.
Qty:
Part Name:
Adapter
Adapter
Mounting Plate
Model
TB
Item:
Detail:
20
A.
B.
C.
Size/Description
TB-mag-A, NEMA, 143 254/6 Frame
TB-mag-A, IEC, 80 - 132 Frame
TB-mag-B/C, NEMA, 143 - 286 Frame
TB-mag-B/C, IEC, 90 - 132 Frame
B/C, Mounting Plate, NEMA, 326 - 405 Frame
B/C, Mounting Plate, IEC, 160 - 180 Frame
B/C, Mounting Plate, IEC, 200 Frame
B/C, Mounting Plate, IEC, 225 Frame
Standard
Material:
Part #
ADP-1000-SI
ADP-1005-SI
ADP-1010-SI
ADP-1015-SI
ADP-1100-SI
ADP-1125-SI
ADP-1135-SI
ADP-1145-SI
Ductile Iron
$/Each
$310.00
$310.00
$617.00
$617.00
$450.00
$550.00
$650.00
$700.00
Qty: 1
Part Name:
Foot, Adapter
One-piece ductile iron casting.
Mounts to a B/C Series Adapter for 8.25 centerline models, Group 2 foot print.
Included Hardware for securing to pump adapter.
Model
TB
Size/Description
TB-mag-B/C
Standard
Material:
Part #
FTA-1000-SI
Ductile Iron
$/Each
$174.00
Page 40 of 65
27
A.
B.
Qty: 1
Part Name:
Wear Ring, Back Stationary
Replaceable, Sintered SiC
Positioned in the Containment Shell.
Model
A1
AL
E1
EL
A3
E3
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
Size/Description
(1.5 x 1 x 6)
(1.5 x 1 x 6) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(1.5 x 1 x 8)
(1.5 x 1 x 8) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6)
(4 x 3 x 6)
(3 x 2 x 8)
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1 x 10)
(2 x 1 x 10) Low Flow
(3 x 1.5 x 10)
(3 x 2 x 10)
(4 x 3 x 10)
(4 x 3 x 10H)
(6 x 4 x 10H)
(6 x 4 x 8)
(2 x 1.5 x 6) Vertical
(2 x 1.5 x 8) Vertical
OD
4.296
4.296
4.296
4.296
4.296
4.296
4.296
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
5.989
8.574
8.574
5.989
4.296
4.296
ID
3.545
3.545
3.545
3.545
3.545
3.545
3.545
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
5.039
7.525
7.525
5.039
3.545
3.545
Standard
Material:
Part #
WRS-1020-SI
WRS-1020-SI
WRS-1020-SI
WRS-1020-SI
WRS-1020-SI
WRS-1020-SI
WRS-1020-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1040-SI
WRS-1070-SI
WRS-1070-SI
WRS-1040-SI
WRS-1020-SI
WRS-1020-SI
SiC
$/Each
$294.00
$294.00
$294.00
$294.00
$294.00
$294.00
$294.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$587.00
$920.00
$920.00
$587.00
$294.00
$294.00
Option 1
Material::
Part #
WRS-1020-DC
WRS-1020-DC
WRS-1020-DC
WRS-1020-DC
WRS-1020-DC
WRS-1020-DC
WRS-1020-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1040-DC
WRS-1070-DC
WRS-1070-DC
WRS-1040-DC
WRS-1020-DC
SiC + DLC
$/Each
$444.00
$444.00
$444.00
$444.00
$444.00
$444.00
$444.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$1,070.00
$1,070.00
$737.00
$444.00
Page 41 of 65
72
A.
B.
Qty: 1
Part Name:
Collar, Thrust
Replaceable, Carbon Filled PTFE or Sintered SiC
Positioned in the Casing Suction.
Stepped Ring
Flat Ring
STYLE A
Stepped Ring, from 1998-2006
Model
A1
AL
E1
EL
A3
E3
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
Size/Description
(1.5 x 1 x 6)
(1.5 x 1 x 6) L. F.
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(1.5 x 1 x 8)
(1.5 x 1 x 8) L. F.
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6)
(4 x 3 x 6)
(3 x 2 x 8)
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1 x 10)
(2 x 1 x 10) L. F.
(3 x 1.5 x 10)
(3 x 2 x 10)
(4 x 3 x 10)
(4 x 3 x 10H)
(6 x 4 x 10H)
(6 x 4 x 8)
(2 x 1.5 x 6) Vertical
(2 x 1.5 x 8) Vertical
Style A
Material:
Style:
Part #
CRT-1010-SI
CRT-1010-SI
CRT-1010-SI
CRT-1010-SI
CRT-1050-SI
CRT-1050-SI
CRT-1050-SI
CRT-1010-SI
CRT-1010-SI
CRT-1010-SI
CRT-1010-SI
CRT-1020-SI
CRT-1020-SI
CRT-1020-SI
CRT-1020-SI
Style B Only
CRT-1020-SI
CRT-1030-SI
CRT-1030-SI
CF-PTFE
A
$/Each
$54.00
$54.00
$54.00
$54.00
$62.00
$62.00
$62.00
$54.00
$54.00
$54.00
$54.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
Style B Only.
CRT-1020-SI
$62.00
Style B Only.
CRT-1010-SI
CRT-1010-SI
$54.00
$54.00
STYLE B
Flat Ring, starting 3/1/06
Style B
Material:
Style:
Part #
CRT-1011-SI
CRT-1011-SI
CRT-1011-SI
CRT-1011-SI
CRT-1051-SI
CRT-1051-SI
CRT-1051-SI
CRT-1011-SI
CRT-1011-SI
CRT-1011-SI
CRT-1011-SI
CRT-1021-SI
CRT-1021-SI
CRT-1021-SI
CRT-1021-SI
CRT-1031-SI
CRT-1021-SI
CRT-1031-SI
CRT-1031-SI
CRT-1051-SI
CRT-1051-SI
CRT-1051-SI
CRT-1021-SI
CRT-1031-SI
CRT-1040-SI
CRT-1060-SI
CF-PTFE
B
$/Each
$54.00
$54.00
$54.00
$54.00
$62.00
$62.00
$62.00
$54.00
$54.00
$54.00
$54.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
$62.00
$144.00
$168.00
CRT-1011-SI
CRT-1011-SI
$54.00
$54.00
Option 1
Material:
Style:
Part #
CRT-1012-SI
CRT-1012-SI
CRT-1012-SI
CRT-1012-SI
CRT-1052-SI
CRT-1052-SI
CRT-1052-SI
CRT-1012-SI
CRT-1012-SI
CRT-1012-SI
CRT-1012-SI
CRT-1022-SI
CRT-1022-SI
CRT-1022-SI
CRT-1022-SI
CRT-1032-SI
CRT-1022-SI
CRT-1032-SI
CRT-1032-SI
CRT-1052-SI
CRT-1052-SI
CRT-1052-SI
CRT-1022-SI
CRT-1032-SI
CRT-1042-SI
CRT-1062-SI
CRT-1048-SI
CRT-1012-SI
CRT-1012-SI
SiC
B
$/Each
$250.00
$250.00
$250.00
$250.00
$272.00
$272.00
$272.00
$250.00
$250.00
$250.00
$250.00
$294.00
$294.00
$294.00
$294.00
$507.00
$507.00
$507.00
$507.00
$272.00
$272.00
$272.00
$294.00
$507.00
$570.00
$870.00
$570.00
$250.00
$250.00
Option 2
Material:
Style:
Part #
CRT-1012-DC
CRT-1012-DC
CRT-1012-DC
CRT-1012-DC
CRT-1052-DC
CRT-1052-DC
CRT-1052-DC
CRT-1012-DC
CRT-1012-DC
CRT-1012-DC
CRT-1012-DC
CRT-1022-DC
CRT-1022-DC
CRT-1022-DC
CRT-1022-DC
CRT-1032-DC
CRT-1032-DC
CRT-1032-DC
CRT-1032-DC
CRT-1052-DC
CRT-1052-DC
CRT-1052-DC
CRT-1022-DC
CRT-1032-DC
CRT-1042-DC
CRT-1062-DC
CRT-1048-DC
CRT-1012-DC
SiC + DLC
B
$/Each
$400.00
$400.00
$400.00
$400.00
$422.00
$422.00
$422.00
$400.00
$400.00
$400.00
$400.00
$444.00
$444.00
$444.00
$444.00
$657.00
$657.00
$657.00
$657.00
$422.00
$422.00
$422.00
$444.00
$657.00
$720.00
$1,020.00
$720.00
$400.00
Note:
Verify the pump serial and casing revision number with Innomag to make sure the correct thrust collar is used.
Page 42 of 65
73
A.
B.
C.
D.
Qty: 1
Part Name:
Gasket, O-RIng
Replaceable, FEP/FKM o-ring standard. Provides universal chemical resistance.
Square cross section: 0.210 x 0.210, more sealing surface that traditional O-rings.
Optional Materials are FKM (Fluorocarbon) or EPDM. Others available upon request.
Positioned between the Casing and Containment Shell.
Model
TB
Item:
Detail:
231
A.
B.
C.
D.
E.
F.
G.
Size/Description
A
B/C 8"
C 10"
Standard
Material:
Part #
GTO-1003-SI
GTO-1013-SI
GTO-1023-SI
FEP/FKM
$/Each
$85.00
$100.00
$125.00
Option 1
Material:
Part #
GTO-1004-SI
GTO-1014-SI
GTO-1024-SI
FKM
$/Each
$85.00
$100.00
$125.00
Option 2
Material:
Part #
GTO-1005-SI
GTO-1015-SI
GTO-1025-SI
EPDM
$/Each
$85.00
$100.00
$125.00
Qty: 1
Part Name:
Shell, Containment
One-piece molding of carbon fiber-reinforced Fluoropolymer ETFE or PFA.
Outer pressure housing molded from Aramid/Vinyl ester composite.
Aramid provides optimum combination of pressure and shock resistance.
Reinforced shaft socket to handle any combination of radial loads.
Zero eddy current losses for no heat operation and maximum possible efficiency.
Front face houses stationary SiC wear ring.
Internal ribs limit swirl to promote fast ejection of fine particles from containment shell.
Model
TB
Size/Description
A
B/C 8"
C 10"
C 10" H
Standard
Material:
Part #
SLC-1000-SI
SLC-1010-SI
SLC-1020-SI
SLC-1030-SI
CF-ETFE/Aramid Composite
$/Each
$413.00
$659.00
$895.00
$895.00
Optional 1
Material:
Part #
SLC-1000-PI
SLC-1010-PI
SLC-1020-PI
SLC-1030-PI
CF-PFA/Aramid Composite
$/Each
$619.50
$988.50
$1,342.50
$1,342.50
Page 43 of 65
232
A.
B.
C.
D.
Qty: 1
Part Name:
Magnet Assembly, Outer
Ductile iron shell with high strength neodymium iron boron magnets.
One drive size per motor frame. Minimum possible inventory.
Keyless hub for fast assembly.
Jackscrew holes provided for easy removal from motor shaft.
Model
TB-A
TB-B/C
Standard
Material:
Part #
D.I./NdFeB Magnets
$/Each
NEMA 56C
MAO-1000-SI
$902.00
NEMA 143/5TC
MAO-1010-SI
$902.00
NEMA 182/4TC
MAO-1020-SI
$902.00
NEMA 213/5TC
MAO-1030-SI
$902.00
MAO-1031-SI
$1,252.00
MAO-1032-SI
$1,252.00
IEC 80
MAO-1005-SI
$902.00
IEC 90
MAO-1015-SI
$902.00
IEC 100/112
MAO-1025-SI
$902.00
IEC 132
MAO-1035-SI
$902.00
MAO-1036-SI
$1,252.00
NEMA 143/5TC
NEMA 182/4TC
NEMA 213/5TC
NEMA 254/6TC
NEMA 254/6TC (1750 rpm, 4 Pole)
NEMA 284/6TSC
NEMA 324/6TSC
NEMA 364/5TSC, High Torque
NEMA 284/6TC
NEMA 284/6TC, High Torque
NEMA 324TC, High Torque
NEMA 326TC/405 TSC, Ultra High Torque
Long Couple Drive - Single
Long Couple Drive - Double
Long Couple Drive - High Torque
Long Couple Drive Ultra High Torque
IEC 90S/L
IEC 100L/112
IEC 132S/M
IEC 132S/M, 7.5 kW @ 1450 rpm
IEC 160M, 12.5 kW @ 2900 rpm
IEC 160M/L
IEC 180M/L
IEC 200L
IEC 180M/L, High Torque
IEC 200L, High Torque
IEC 225M, High Torque
MAO-1040-SI
MAO-1050-SI
MAO-1060-SI
MAO-1070-SI
MAO-1080-SI
MAO-1080-SI
MAO-1090-SI
MAO-1100-SI
MAO-1110-SI
MAO-1111-SI
MAO-1120-SI
MAO-1122-SI
MAO-2100-SI
MAO-2110-SI
MAO-2120-SI
MAO-2121-SI
MAO-1055-SI
MAO-1065-SI
MAO-1075-SI
MAO-1076-SI
MAO-1085-SI
MAO-1095-SI
MAO-1105-SI
MAO-1115-SI
MAO-1106-SI
MAO-1116-SI
MAO-1125-SI
$1,300.00
$1,300.00
$1,300.00
$1,300.00
$2,100.00
$2,100.00
$2,100.00
$2,600.00
$2,100.00
$2,600.00
$2,600.00
$3,250.00
$1,300.00
$2,100.00
$2,600.00
$3,250.00
$1,300.00
$1,300.00
$1,300.00
$2,100.00
$1,300.00
$2,100.00
$2,100.00
$2,100.00
$2,600.00
$2,600.00
$2,600.00
MAO-1126-SI
$3,250.00
Size/Description
Page 44 of 65
235
Qty: 2
Part Name:
Bushing, Bearing
A. Tandem bearing system made of pure sintered silicon carbide (SiC)
B. Separately mounted for optimum alignment with shaft.
Model
Size/Description
A 1.000 I.D.
B/C 1.500 I.D.
TB
Item:
236
Detail:
A.
Qty:
Part Name:
Option 1
Material:
Part #
BGB-1005-DC
BGB-1015-DC
SiC+ DLC
$/Each
$388.00
$400.00
Bushing, Spacer
TB
Detail:
SiC
$/Each
$238.00
$250.00
Model
Item:
Standard
Material:
Part #
BGB-1005-SI
BGB-1015-SI
Size/Description
A
B/C
Standard
Material:
Part #
BGB-1050-SI
BGB-1060-SI
PTFE
$/Each
$29.00
$41.00
239
Qty: 1
Part Name:
Ring, Containment
A. One-piece ductile iron casting.
B. Aligns and supports the containment shell.
C. Jackscrew holes provided for easy disassembly
Model
TB
Size/Description
A - ANSI
A - ISO/JIS
B/C - ANSI 8"
B/C - ISO/JIS 8"
Secondary Sealed Unit 8
B/C - ANSI 10"
B/C - ISO/JIS 10"
Secondary Sealed Unit 10
Standard
Material:
Part #
RGC-1000-SI
RGC-1005-SI
RGC-1010-SI
RGC-1015-SI
RGC-2110-SI
RCG-1020-SI
RGC-1025-SI
RGC-2120-SI
Ductile Iron
$/Each
$170.00
$170.00
$312.00
$312.00
$312.00
$365.00
$365.00
$365.00
Page 45 of 65
300
Detail:
A.
Qty:
14
Part Name:
Model
TB-A
TB-B/C
Item:
301
Detail:
A.
Qty:
14
Part Name:
TB-B/C
302
A.
1/2"-13 x 1.25"
HDW-1021-SI
$1.50
M12-1.75x30mm
HDW-1035-SI
$1.50
5/8"-11 x 1.50"
HDW-1042-SI
$2.50
M16-2.0x40mm
HDW-1049-SI
$2.50
Lock Washer
TB-A
Detail:
304 SS
$/Each
Model
Item:
Size/Description
Standard
Material:
Part #
Qty:
Part Name:
Size/Description
1/2"
5/8"
Standard
Material:
Part #
304 SS
$/Each
HDW-1140-SI
$0.50
HDW-1145-SI
$0.50
HDW-1160-SI
$0.95
HDW-1165-SI
$0.95
Plug
Model
TB
Size/Description
A/B/C - 1/2" NPT, Top of Adapter, 18-8 SS
A/B/C - 1/2" NPT, Bottom of Adapter, Red, PP.
Standard
Part #
HDW-1230-SI
HDW-1500-SI
$/Each
$8.00
$2.00
Page 46 of 65
370
Detail:
A.
Qty:
Part Name:
Drain Flange
Model
TB
Item:
371
Detail:
A.
Qty:
Part Name:
372
Detail:
A.
304 SS
$/Each
$45.00
Model
TB
Item:
Size/Description
A/B/C - Flange
Standard
Material:
Part #
SUB-1350-SI
Qty:
Part Name:
Size/Description
A/B/C Drain Gasket
Standard
Material:
Part #
GTO-1040-SI
PTFE
$/Each
$25.00
Model
TB
Size/Description
A/B/C Drain Gasket Backing
Standard
Material:
Part #
GTO-1050-SI
Neoprene
$/Each
$15.00
Page 47 of 65
2
A.
B.
Qty: 1
Part Name:
Impeller Magnet, Complete
Molded one-piece enclosed impeller made of carbon fiber-reinforced ETFE or PFA.
Magnet assembly hermetically sealed by Patented Tru-Seal Design.
8b
Qty: 1
9c
235
Qty: 2 sets
)
8a
Qty: 2
Qty: 1
236
Qty: 1
Qty: 1
14
Qty: 1
Model
A1
AL
E1
EL
A3
E3
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
G2
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
Size/Description
(1.5 x 1 x 6)
(1.5 x 1 x 6) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 1.5 x 6)
(65mm x 40mm)
(3 x 2 x 6)
(1.5 x 1 x 8)
(1.5 x 1 x 8) Low Flow
(50mm x 32mm)
(50mm x 32mm)
(3 x 2 x 6)
(3 x 1.5 x 8)
65mm x 40mm
(3 x 2 x 6)
(4 x 3 x 6)
(3 x 2 x 8)
(4 x 3 x 8)
(100mm x 65mm)
(2 x 1 x 10)
(2 x 1 x 10) Low Flow
(3 x 1.5 x 10)
(3 x 2 x 10)
(4 x 3 x 10)
(4 x 3 x 10) Ultra High Torque
(4 x 3 x 10H)
(4 x 3 x 10H) Ultra High Torque
(6 x 4 x 10H)
(6 x 4 x 10H) Ultra High Torque
(6 x 4 x 8)
(6 x 4 x 8) Ultra High Torque
(2 x 1.5 x 6) Vertical
(2 x 1.5 x 8) Vertical
Standard
Impeller:
Part #
IMA -1010-AA
IMA -1010-AA
IMA -1010-AA
IMA -1010-AA
IMA -1070-AA
IMA -1070-AA
IMA -1070-AA
IMA -1030-AA
IMA -1030-AA
IMA -1030-AA
IMA -1030-AA
IMA -1020-AA
IMA -1040-AA
IMA -1040-AA
IMA -1020-AA
IMA -1065-AA
IMA -1050-AA
IMA -1060-AA
IMA -1060-AA
IMA -1100-AA
IMA -1100-AA
IMA -1100-AA
IMA -1120-AA
IMA -1130-AA
IMA -1132-AA
IMA -1140-AA
IMA -1142-AA
IMA -1150-AA
IMA -1152-AA
IMA -1155-AA
IMA -1157-AA
IMA -1010-AA
IMA -1030-AA
CF/ETFE
$/Each
$1,480.00
$1,480.00
$1,480.00
$1,480.00
$1,525.00
$1,525.00
$1,525.00
$1,790.00
$1,790.00
$1,790.00
$1,790.00
$2,150.00
$2,150.00
$2,150.00
$2,150.00
$2,150.00
$2,550.00
$2,750.00
$2,750.00
$2,250.00
$2,250.00
$2,250.00
$2,650.00
$2,950.00
$3,600.00
$3,050.00
$3,700.00
$3,450.00
$4,100.00
$3,650.00
$4,300.00
$1,480.00
$1,790.00
Option 1
Impeller:
Part #
IMA -1010-PA
IMA -1010-PA
IMA -1010-PA
IMA -1010-PA
IMA -1070-PA
IMA -1070-PA
IMA -1070-PA
IMA -1030-PA
IMA -1030-PA
IMA -1030-PA
IMA -1030-PA
IMA -1020-PA
IMA -1040-PA
IMA -1040-PA
IMA -1020-PA
IMA -1065-PA
IMA -1050-PA
IMA -1060-PA
IMA -1060-PA
IMA -1100-PA
IMA -1100-PA
IMA -1100-PA
IMA -1120-PA
IMA -1130-PA
CF/PFA
$/Each
$2,220.00
$2,220.00
$2,220.00
$2,220.00
$2,287.50
$2,287.50
$2,287.50
$2,685.00
$2,685.00
$2,685.00
$2,685.00
$3,225.00
$3,225.00
$3,225.00
$3,225.00
$3,225.00
$3,825.00
$4,125.00
$4,125.00
$3,375.00
$3,375.00
$3,375.00
$3,975.00
$4,425.00
IMA -1140-PA
$4,575.00
IMA -1150-PA
$5,175.00
IMA -1155-PA
$4,575.00
IMA -1010-PA
$2,220.00
Page 48 of 65
Detail:
231
A.
B.
C.
D.
E.
F.
G.
Qty: 1
Part Name:
Containment Shell, Complete
One-piece molding of carbon fiber-reinforced Fluoropolymer ETFE or PFA.
Outer pressure housing molded from Aramid/Vinyl ester composite.
Aramid provides optimum combination of pressure and shock resistance.
Reinforced shaft socket to handle any combination of radial loads.
Zero eddy current losses for no heat operation and maximum possible efficiency.
Front face houses stationary SiC wear ring.
Internal ribs limit swirl to promote fast ejection of fine particles from containment shell.
73
Qty: 1
)
231
Qty: 1
)
6
Qty: 1
)
27
Qty: 1
)
9b
Qty: 1
)
Model
TB
Size/Description
A
B/C 8"
C 10"
C 10" H
Standard
Material:
Part #
SLC-1000-AA
SLC-1010-AA
SLC-1020-AA
SLC-1030-AA
CF-ETFE/Aramid Composite
$/Each
$936.00
$1,550.00
$1,950.00
$2,550.00
Optional 1
Material:
Part #
SLC-1000-PA
SLC-1010-PA
SLC-1020-PA
SLC-1030-PA
CF-PFA/Aramid Composite
$/Each
$1,404.00
$2,325.00
$2,925.00
$3,825.00
Page 49 of 65
1
A.
B.
C.
D.
Qty: 1
Part Name:
Casing, Lined
One piece cast ductile iron.
Bonded ETFE or PFA lining, minimum of 1/8 (3mm) thickness.
Self venting, top centerline discharge design.
Two bolt flanged drain with pure PTFE gasket and 316SS blind flange, standard.
9a
Qty: 1
)
Qty: 1
)
7
Qty: 1
)
72
Qty: 1
)
300,301
371
Qty: 1
)
Qty: 1
)
370
372
Qty: 1
)
Model
A1
AL
E1
EL
A3
E3
Size/Description
1.5 x 1 - ANSI class 150
1.5 x 1 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
1.5 x 1 - ANSI class 150
1.5 x 1 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
2.0 x 1.5 - ANSI class 150
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
2.0 x 1.5 - ANSI class 150
3 x 1.5 - ANSI class 150
3 x 1.5 - ANSI class 300
65 x 40mm - ISO PN 16
65 x 50mm - ISO PN 16
65 x 50mm - JIS 10 kg/cm^2
65 x 50mm - ISO PN 16
65 x 40mm - ISO PN 16
65 x 50mm - JIS 10 kg/cm^2
3 x 2 - ANSI class 150
Qty: 1
)
Standard Material
D.I./ETFE Lined Casing
Part #
$/Each
CSG-1010-AA
$1,200.00
CSG-1011-AA
$1,200.00
CSG-1012-AA
$1,200.00
CSG-1013-AA
$1,200.00
CSG-1010-LB
$1,200.00
CSG-1011-LB
$1,200.00
CSG-1012-LB
$1,200.00
CSG-1013-LB
$1,200.00
CSG-1015-AA
$1,200.00
CSG-1017-AA
$1,200.00
CSG-1018-AA
$1,200.00
CSG-1015-LB
$1,200.00
CSG-1017-LB
$1,200.00
CSG-1018-LB
$1,200.00
CSG-1070-AA
$1,500.00
CSG-1071-AA
$1,500.00
CSG-1072-AA
$1,500.00
CSG-1073-AA
$1,500.00
CSG-1074-AA
$1,500.00
CSG-107A-AA
$1,500.00
CSG-107B-AA
$1,500.00
CSG-107C-AA
$1,500.00
CSG-107D-AA
$1,500.00
Optional Material 1
D.I./PFA Lined Casing
Part #
$/Each
CSG-1010-PA
$2,400.00
CSG-1011-PA
$2,400.00
CSG-1012-PA
$2,400.00
CSG-1013-PA
$2,400.00
CSG-1010-PB
$2,400.00
CSG-1011-PB
$2,400.00
CSG-1012-PB
$2,400.00
CSG-1013-PB
$2,400.00
CSG-1015-PA
$2,400.00
CSG-1017-PA
$2,400.00
CSG-1018-PA
$2,400.00
CSG-1015-PB
$2,400.00
CSG-1017-PB
$2,400.00
CSG-1018-PB
$2,400.00
CSG-1070-PA
$3,000.00
CSG-1071-PA
$3,000.00
CSG-1072-PA
$3,000.00
CSG-1073-PA
$3,000.00
CSG-1074-PA
$3,000.00
CSG-107A-PA
$3,000.00
CSG-107B-PA
$3,000.00
CSG-107C-PA
$3,000.00
CSG-107D-PA
$3,000.00
Page 50 of 65
Model
A4
B1
BL
F1
FL
B3
B4
F4
B5
B6
C1
C2
Size/Description
3 x 2 - ANSI class 150
3 x 2 - ANSI class 300
80 x 50mm - ISO PN 16
80 x 65mm - ISO PN 16
80 x 65mm - JIS 10 kg/cm^2
1.5 x 1 - ANSI class 150
1.5 x 1 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
1.5 x 1 - ANSI class 150
1.5 x 1 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
2.0 x 1.5 - ANSI class 150
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
2.0 x 1.5 - ANSI class 150
3 x 2 - ANSI class 150
3 x 2 - ANSI class 300
80 x 50mm - ISO PN 16
80 x 65mm - JIS 10 kg/cm^2
3 x 1.5 - ANSI class 150
3 x 1.5 - ANSI class 300
65 x 40mm - ISO PN 16
65 x 50mm - ISO PN 16
65 x 50mm - JIS 10 kg/cm^2
65 x 40mm - ISO PN 16
65 x 50mm - JIS 10 kg/cm^2
3 x 1.5 - ANSI class 150
3x2 (A10) - ANSI class 150
3x2 (A10) - ANSI class 300
80 x 50mm - ISO PN 16
80 x 65mm - ISO PN 16
80 x 65mm - JIS 10 kg/cm^2
4x3 - ANSI class 150
4x3 - ANSI class 300
100 x 65mm - ISO PN 16
100 x 80mm - ISO PN 16
100 x 80mm - JIS 10 kg/cm^2
3 x 2 - ANSI class 150
3 x 2 - ANSI class 300
80 x 50mm - ISO PN 16
80 x 65mm - JIS 10 kg/cm^2
4 x 3 - ANSI class 150
4 x 3 - ANSI class 300
100 x 65mm - ISO PN 16
100 x 80mm - JIS 10 kg/cm^2
100 x 80mm - ISO PN 16
Standard Material
D.I./ETFE Lined Casing
Part #
$/Each
CSG-1075-AA
$1,500.00
CSG-1076-AA
$1,500.00
CSG-1077-AA
$1,500.00
CSG-1078-AA
$1,500.00
CSG-1079-AA
$1,500.00
CSG-1030-AA
$1,900.00
CSG-1031-AA
$1,900.00
CSG-1032-AA
$1,900.00
CSG-1033-AA
$1,900.00
CSG-1030-LB
$1,900.00
CSG-1031-LB
$1,900.00
CSG-1032-LB
$1,900.00
CSG-1033-LB
$1,900.00
CSG-1035-AA
$1,900.00
CSG-1037-AA
$1,900.00
CSG-1038-AA
$1,900.00
CSG-1035-LB
$1,900.00
CSG-1037-LB
$1,900.00
CSG-1038-LB
$1,900.00
CSG-1020-AA
$1,925.00
CSG-1021-AA
$1,925.00
CSG-1022-AA
$1,925.00
CSG-1023-AA
$1,925.00
CSG-1080-AA
$2,150.00
CSG-1081-AA
$2,150.00
CSG-1082-AA
$2,150.00
CSG-1083-AA
$2,150.00
CSG-1084-AA
$2,150.00
CSG-1085-AA
$2,150.00
CSG-1087-AA
$2,150.00
CSG-1088-AA
$2,150.00
CSG-1090-AA
$1,925.00
CSG-1091-AA
$1,925.00
CSG-1092-AA
$1,925.00
CSG-1093-AA
$1,925.00
CSG-1094-AA
$1,925.00
CSG-1160-AA
$2,850.00
CSG-1161-AA
$2,850.00
CSG-1162-AA
$2,850.00
CSG-1163-AA
$2,850.00
CSG-1164-AA
$2,850.00
CSG-1050-AA
$2,400.00
CSG-1051-AA
$2,400.00
CSG-1052-AA
$2,400.00
CSG-1053-AA
$2,400.00
CSG-1060-AA
$2,850.00
CSG-1061-AA
$2,850.00
CSG-1062-AA
$2,850.00
CSG-1063-AA
$2,850.00
CSG-1064-AA
$2,850.00
Optional Material 1
D.I./PFA Lined Casing
Part #
$/Each
CSG-1075-PA
$3,000.00
CSG-1076-PA
$3,000.00
CSG-1077-PA
$3,000.00
CSG-1078-PA
$3,000.00
CSG-1079-PA
$3,000.00
CSG-1030-PA
$3,800.00
CSG-1031-PA
$3,800.00
CSG-1032-PA
$3,800.00
CSG-1033-PA
$3,800.00
CSG-1030-PA
$3,800.00
CSG-1031-PA
$3,800.00
CSG-1032-PA
$3,800.00
CSG-1033-PA
$3,800.00
CSG-1035-PA
$3,800.00
CSG-1037-PA
$3,800.00
CSG-1038-PA
$3,800.00
CSG-1035-PB
$3,800.00
CSG-1037-PB
$3,800.00
CSG-1038-PB
$3,800.00
CSG-1020-PA
$3,850.00
CSG-1021-PA
$3,850.00
CSG-1022-PA
$3,850.00
CSG-1023-PA
$3,850.00
CSG-1080-PA
$4,300.00
CSG-1081-PA
$4,300.00
CSG-1082-PA
$4,300.00
CSG-1083-PA
$4,300.00
CSG-1084-PA
$4,300.00
CSG-1085-PA
$4,300.00
CSG-1087-PA
$4,300.00
CSG-1088-PA
$4,300.00
CSG-1090-PA
$3,850.00
CSG-1091-PA
$3,850.00
CSG-1092-PA
$3,850.00
CSG-1093-PA
$3,850.00
CSG-1094-PA
$3,850.00
CSG-1160-PA
$5,700.00
CSG-1161-PA
$5,700.00
CSG-1162-PA
$5,700.00
CSG-1163-PA
$5,700.00
CSG-1164-PA
$5,700.00
CSG-1050-PA
$4,800.00
CSG-1051-PA
$4,800.00
CSG-1052-PA
$4,800.00
CSG-1053-PA
$4,800.00
CSG-1060-PA
$5,700.00
CSG-1061-PA
$5,700.00
CSG-1062-PA
$5,700.00
CSG-1063-PA
$5,700.00
CSG-1064-PA
$5,700.00
Page 51 of 65
Model
G2
C3
CL
C4
C5
C6
C7
C8
C9
V1
W1
Size/Description
100 x 65mm - ISO PN 16
100 x 80mm - JIS 10 kg/cm^2
4 x 3 - ANSI class 150
2x1 - ANSI class 150
2x1 - ANSI class 300
50 x 32mm - ISO PN 16
2x1 - ANSI class 150
2x1 - ANSI class 300
50 x 32mm - ISO PN 16
3x1.5 - ANSI class 150
3x1.5 - ANSI class 300
65 x 40mm - ISO PN 16
65 x 50mm - ISO PN 16
65 x 50mm - JIS 10 kg/cm^2
3x2 - ANSI class 150
3x2 - ANSI class 300
80 x 50mm - ISO PN 16
80 x 65mm - ISO PN 16
80 x 65mm - JIS 10 kg/cm^2
4x3 - ANSI class 150
4x3 - ANSI class 300
100 x 65mm - ISO PN 16
100 x 80mm - ISO PN 16
100 x 80mm - JIS 10 kg/cm^2
4x3 - ANSI class 150
4x3 - ANSI class 300
100 x 65mm - ISO PN 16
100 x 80mm - ISO PN 16
100 x 80mm - JIS 10 kg/cm^2
6x4 - ANSI class 150
6x4 - ANSI class 300
150 x 100mm - ISO PN 16
150 x 125mm - ISO PN 16
150 x 125mm - JIS 10 kg/cm^2
6x4 - ANSI class 150
6x4 - ANSI class 300
150 x 125mm - ISO PN 16
150 x 125mm - JIS 10 kg/cm^2
2 x 1.5 x 6 - ANSI class 150
2 x 1.5 x 6 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
2 x 1.5 x 8 - ANSI class 150
2 x 1.5 x 8 - ANSI class 300
50 x 32mm - ISO PN 16
50 x 40mm - JIS 10 kg/cm^2
Standard Material
D.I./ETFE Lined Casing
Part #
$/Each
CSG-1065-AA
$2,850.00
CSG-1067-AA
$2,850.00
CSG-1068-AA
$2,850.00
CSG-1100-AA
$2,375.00
CSG-1101-AA
$2,375.00
CSG-1102-AA
$2,375.00
CSG-1100-LB
$2,375.00
CSG-1101-LB
$2,375.00
CSG-1102-LB
$2,375.00
CSG-1110-AA
$2,400.00
CSG-1111-AA
$2,400.00
CSG-1112-AA
$2,400.00
CSG-1113-AA
$2,400.00
CSG-1114-AA
$2,400.00
CSG-1120-AA
$2,990.00
CSG-1121-AA
$2,990.00
CSG-1122-AA
$2,990.00
CSG-1123-AA
$2,990.00
CSG-1124-AA
$2,990.00
CSG-1130-AA
$3,320.00
CSG-1131-AA
$3,320.00
CSG-1132-AA
$3,320.00
CSG-1133-AA
$3,320.00
CSG-1134-AA
$3,320.00
CSG-1140-AA
$3,500.00
CSG-1141-AA
$3,500.00
CSG-1142-AA
$3,500.00
CSG-1143-AA
$3,500.00
CSG-1144-AA
$3,500.00
CSG-1150-AA
$4,140.00
CSG-1151-AA
$4,140.00
CSG-1152-AA
$4,140.00
CSG-1153-AA
$4,140.00
CSG-1154-AA
$4,140.00
CSG-1155-AA
$4,140.00
CSG-1156-AA
$4,140.00
CSG-1157-AA
$4,140.00
CSG-1158-AA
$4,140.00
CSG-1210-AA
$2,400.00
CSG-1211-AA
$2,400.00
CSG-1212-AA
$2,400.00
CSG-1213-AA
$2,400.00
CSG-1230-AA
$2,500.00
CSG-1231-AA
$2,500.00
CSG-1232-AA
$2,500.00
CSG-1233-AA
$2,500.00
Optional Material 1
D.I./PFA Lined Casing
Part #
$/Each
CSG-1065-PA
$5,700.00
CSG-1067-PA
$5,700.00
CSG-1068-PA
$5,700.00
CSG-1100-PA
$4,750.00
CSG-1101-PA
$4,750.00
CSG-1102-PA
$4,750.00
CSG-1100-PB
$4,750.00
CSG-1101-PB
$4,750.00
CSG-1102-PB
$4,750.00
CSG-1110-PA
$4,800.00
CSG-1111-PA
$4,800.00
CSG-1112-PA
$4,800.00
CSG-1113-PA
$4,800.00
CSG-1114-PA
$4,800.00
CSG-1120-PA
$5,980.00
CSG-1121-PA
$5,980.00
CSG-1122-PA
$5,980.00
CSG-1123-PA
$5,980.00
CSG-1124-PA
$5,980.00
CSG-1130-PA
$6,640.00
CSG-1131-PA
$6,640.00
CSG-1132-PA
$6,640.00
CSG-1133-PA
$6,640.00
CSG-1134-PA
$6,640.00
CSG-1140-PA
$7,000.00
CSG-1141-PA
$7,000.00
CSG-1142-PA
$7,000.00
CSG-1143-PA
$7,000.00
CSG-1144-PA
$7,000.00
CSG-1150-PA
$8,280.00
CSG-1151-PA
$8,280.00
CSG-1152-PA
$8,280.00
CSG-1154-PA
CSG-1155-PA
CSG-1156-PA
CSG-1157-PA
CSG-1158-PA
CSG-1210-PA
CSG-1211-PA
CSG-1212-PA
CSG-1213-PA
CSG-1230-PA
CSG-1231-PA
CSG-1232-PA
CSG-1233-PA
$8,280.00
$8,280.00
$8,280.00
$8,280.00
$8,280.00
$4,300.00
$4,300.00
$4,300.00
$4,300.00
$4,400.00
$4,400.00
$4,400.00
$4,400.00
Page 52 of 65
Gasket, O-Ring
Model
TB
Size/Description
A
B/C 8"
C 10"
Standard
Material:
Part #
GTO-1003-SI
GTO-1013-SI
GTO-1023-SI
FEP/FKM
$/Each
$85.00
$100.00
$125.00
Option 1
Material:
Part #
GTO-1004-SI
GTO-1014-SI
GTO-1024-SI
FKM
$/Each
$85.00
$100.00
$125.00
Option 2
Material:
Part #
GTO-1005-SI
GTO-1015-SI
GTO-1025-SI
EPDM
$/Each
$85.00
$100.00
$125.00
Bushing, Bearing
Model
TB
Size/Description
A 1.000 I.D. (2-Required)
B/C 1.500 I.D. (2-Required)
A Bearing Spacer (1-Required)
B/C Bearing Spacer (1-Required)
Standard
Material:
Part #
BGB-1005-SI
BGB-1015-SI
BGB-1050-SI
BGB-1060-SI
SiC
$/Each
$238.00
$250.00
$29.00
$41.00
Option 1
Material:
Part #
BGB-1005-DC
BGB-1015-DC
SiC+ DLC
$/Each
$388.00
$400.00
Gasket, O-Ring
Model
TB
Size/Description
A
B/C 8"
C 10"
Standard
Material:
Part #
GTO-1003-SI
GTO-1013-SI
GTO-1023-SI
FEP/FKM
$/Each
$85.00
$100.00
$125.00
Option 1
Material:
Part #
GTO-1004-SI
GTO-1014-SI
GTO-1024-SI
FKM
$/Each
$85.00
$100.00
$125.00
Option 2
Material:
Part #
GTO-1005-SI
GTO-1015-SI
GTO-1025-SI
EPDM
$/Each
$85.00
$100.00
$125.00
Shaft, Pump
Model
TB
Size/Description
A-Series - O.D. = 1.00" (Before 9-1-2007)
A-Series - O.D. = 1.00" (Current)
B/C-Series - O.D. = 1.50" (Before 9-1-2007)
B/C-Series - O.D. = 1.50" (Current)
Standard
Material:
Part #
STP-1000-SI
STP-1005-SI
STP-1010-SI
STP-1015-SI
SiC
$/Each
$477.00
$477.00
$595.00
$595.00
Option 1
Material:
Part #
STP-1000-DC
SiC + DLC
$/Each
$627.00
STP-1010-DC
$745.00
Page 53 of 65
Model
TB
(Includes 1-Containment Shell, 1-Wear Ring, 1-Pump Shaft, 1-Gasket O-Ring, 1-Retaining Ring)
Standard
Optional 1
Material:
CF-ETFE/Aramid Composite
Material:
CF-PFA/Aramid Composite
Size/Description
Part #
$/Each
Part #
$/Each
A
SLC-1000-AA
$936.00
SLC-1000-PA
$1,404.00
B/C 8"
SLC-1010-AA
$1,550.00
SLC-1010-PA
$2,325.00
C 10"
SLC-1020-AA
$1,950.00
SLC-1020-PA
$2,925.00
C 10" H
SLC-1030-AA
$2,550.00
SLC-1030-PA
$3,825.00
Page 54 of 65
Model
TB
Part Name
Detail:
A.
Model
TB
Part Name
Detail:
Size/Description
A/B/C
Standard Material
PTFE/304 SS
Part #
$/Each
SUB-1350-AA $225.00
Size/Description
1.5 Flange, 2.00 Thick
2 Flange, 1.75 Thick
3 Flange, 1.50 Thick
Standard Material
PTFE/Carbon Steel
Part #
$/Each
SUB-1500-AA $225.00
SUB-1510-AA $225.00
SUB-1507-AA $400.00
Model
TB
Size/Description
1.5 Flange, 5.25 Pump Centerline
3 Flange, 5.25 Pump Centerline
Standard Material
ETFE Lined/Carbon Steel
Part #
$/Each
PCG-1100-AA $2600.00
PCG-1105-AA $2600.00
Page 55 of 65
Base, Steel
A. Solid Steel C-Channel
B. Corrosion Resistant Epoxy + Polyurethane Paint
Model
TB
Part Name
Detail:
Size/Description
12x34x3
15x40x3.5
18x48x4
Standard Material
Carbon Steel
Part #
$/Each
BSE-1000-SI $380.00
BSE-1110-SI $710.00
BSE-1120-SI $930.00
Model
TB
Size/Description
Single row outer drive (MAO-2100-SI) B-Series
Double row outer drive (MAO-2110-SI) C-Series
Double row (High Torque) outer drive (MAO-2120-SI)
Standard Material
Ductile Iron/Polyurethane Paint
Part #
$/Each
BFR-2000-AA
$3,500.00
BFR-2010-AA
$4,300.00
BFR-2020-AA
$4,800.00
Page 56 of 65
Model
TB
Part Name
Detail:
Size/Description
Single row outer drive (MAO-2100-SI) B-Series
Double row outer drive (MAO-2110-SI) C-Series
Double row (High Torque) outer drive (MAO-2120-SI)
Standard Material
Ductile Iron/Polyurethane Paint
Part #
$/Each
BFR-2050-AA
$8,500.00
BFR-2060-AA
$9,300.00
BFR-2070-AA
$9,800.00
Model
TB
Size/Description
Bushing Bearing Service Kit A/B/C Series
Standard Material
Carbon Steel/Aluminum
Part #
$/Each
TLG-2016-AA $120.00
Page 57 of 65
Model
TB
Part Name
Trimming Sleeve
Detail:
A.
Size/Description
Shaft Removal Kit for A Series
Shaft Removal Kit for B/C Series
Standard Material
Carbon Steel/Aluminum
Part #
$/Each
TLG-2017-AA
$40.00
TLG-2018-AA
$50.00
Split PVC tubing protects the magnet assembly while trimming the impeller.
Model
TB
Size/Description
Trimming Sleeve for A Series
Trimming Sleeve for B/C Series
Standard Material
PVC
Part #
$/Each
TLG-2033-AA $20.00
TLG-2023-AA $20.00
Page 58 of 65
Description
Part #
Standard
Part #
Witnessed
Hydrostatic
TST-1040-SI
No-Charge
TST-1050-SI
$150.00
TST-1060-SI
$150.00
TST-1070-SI
$250.00
Vibration Test
Vibration monitoring/measurement
TST-0800-SI
$150.00
TST-0810-SI
$250.00
Performance
TST-0900-SI
No-Charge
TST-0910-SI
$150.00
TST-1000-SI
$250.00
TST-1010-SI
$350.00
TST-1020-SI
$350.00
TST-1030-SI
$700.00
TST-1032-SI
$450.00
TST-1034-SI
$900.00
Endurance
TST-1080-SI
$50.00
TST-1090-SI
$125.00
Certified Drawing
ENG-1000-SI
$50.00
Custom Drawing
ENG-1010-SI
$100.00/Hr
Motor Mounting
LBR-1010-SI
$100.00
Base Mounting
LBR-1020-SI
$100.00
Base Drilling CS
LBR-1030-SI
$50.00
Base Drilling PC
LBR-1040-SI
$100.00
NPSH
Page 59 of 65
50 Hz IEC
RPM
Frame
00118EP3E143TC
1800
143TC
$371.00
00156EP3E143TC
3600
143TC
$375.000
1.5
00158EP3E145TC
1800
145TC
$381.00
00236EP3E145TC
3600
145TC
$448.00
00218EP3E145TC
1800
145TC
$420.00
00336EP3E182TC
3600
182TC
$530.00
7.5
10
15
20
25
30
40
Part Number
List Price
kW
0.75
1.13
1.5
2.25
RPM
Part Number
1500/1800
.7518EP3EAL80
SH 80-4B
$388.00
00118EP3EAL90S
SH 90S-4
$458.00
3000/3600
00136EP3EAL80
SH 90S-2
$422.00
1500/1800
00158EP3EAL90L
SH 90L-4
$525.00
3000/3600
00156EP3EAL90S
SH 90L-2
$491.00
1500/1800
00218EP3EAL100L
SG 100L-4A
$598.00
1800
182TC
$489.00
00536EP3E184TC
3600
284TC
$636.00
00518EP3E184TC
1800
184TC
$578.00
00736EP3E213TC
3600
213TC
$816.00
00718EP3E213TC
1800
213TC
$764.00
01036EP3E215TC
3600
215TC
$959.00
01018EP3E215TC
1800
215TC
$921.00
01536EP3E254TC
3600
254TC
$1,322.00
01518EP3E254TC
1800
254TC
$1,254.00
02036EP3E256TC
3600
256TC
$1,693.00
02018EP3E256TC
1800
256TC
$1,612.00
02536EP3E284TSC
3600
284TSC
$1,962.00
02518EP3E284TC
1800
284TC
$1,881.00
03036EP3E286TSC
3600
286TSC
$2,353.00
03018EP3E286TC
1800
286TC
$2,360.00
04036EP3E324TSC
3600
324TSC
$3,657.00
1500/1800
04018EP3E324TC
1800
324TC
$3,276.00
22.5
3000/3600
326TSC
$3,983.00
30
3000/3600
03036EP3E200L,
4.13
5.63
7.5
11.25
15
18.75
List Price
1500/1800
00318EP3E182TC
Frame
3000/3600
00236EP3EAL90L
SG 100L-2
$718.00
1500/1800
00318EP3EAL100L
SG 100L-4B
$659.00
3000/3600
00336EP3EAL100L
SG 112M-2
$754.00
1500/1800
00418EP3EAL112M
$688.00
3000/3600
00436EP3EAL112M
SG 112M-4
SG 132S2A
1500/1800
00518EP3EAL132S
SG 132S-4
SG 132S2B
$839.00
3000/3600
00536EP3EAL132S
1500/1800
00718EP3EAL132M
3000/3600
00736EP3EAL132S
1500/1800
01118EP3E160M
SG 132M-4
SG 160M2A
$832.00
$1069.00
$968.00
$1,111.00
3000/3600
01136EP3E160M
SG 160M-4
SG 160M2B
$1,539.00
1500/1800
01518EP3E160L
SG 160L-4
$2,003.00
3000/3600
01518EP3E160M
SG 160L-2
$2,148.00
1500/1800
01818EP3E180M
SG 180M-4
$2,370.00
3000/3600
01836EP3E160L
SG 180M-2
$2,706.00
02218EP3E180L
SG 180L-4
$2,944.00
02236EP3E180M
SG 200L-2A
$3,068.00
SG 200L-2B
$4,238.00
$1760.00
05036EP3E326TSC
3600
50
05018EP3E326TC
1800
326TC
$3,564.00
37.5
3000/3600
03736EP3E200L
SG 225M-2
$4,790.00
60
06036EP3E364TSC
3600
364TSC
$5,549.00
45
3000/3600
04536EP3E225S/M
SG 250M-2
$6,802.00
75
07536EP3E365TSC
3600
365TSC
$6,603.00
56.25
3000/3600
05536EP3E250S/M
SG 280S-2
$8,436.00
$8,237.00
100
10036EP3E405TSC
3600
405TSC
Page 60 of 65
Protection - Pre-alarm, alarm and stop before any machine over or under load damage occurs. This increase life
time and reduce spare parts requirements.
All in one - You will readout the motor shaft power in % of rated power, kW or HP. The analogue output
signal can be scaled to desired shaft power range and used as an input to controllers etc. Furthermore, two relay
outputs.
Easy to install - No sensors or sensor cables. This results in less components and easy set and start up. Alarm
functions can be set within three seconds at just one push of a key.
It is applicable for all kinds of pumps, mixers, agitators, blenders, scrapers, conveyers, machine tools,
automatic gates and doors.
In other words EL-FI M20 takes care of your equipment before it is too late.
Part Number
01-2520-20
01-2520-40
01-2520-50
CTM 010 # 01-2471-10
CTM 025 # 01-2471-20
CTM 050 # 01-2471-30
CTM 100 # 01-2471-40
Description
1 or 3P, 100-240V, Display hp or kW, Max/Min Limits. 4-20mA Out
3P, 380-500V, Display hp or kW, Max/Min Limits, 4-20mA Out
3P, 525-600V, Display hp or kW, Max/Min Limits, 4-20mA Out
Current Transformer, 0.1-10 amps FLA
Current Transformer, 10.1-25 amps FLA
Current Transformer, 25.1-50 amps FLA
Current Transformer, 50.1-100 amps FLA
Price/Each
$640.00
$640.00
$640.00
$65.00
$65.00
$65.00
$65.00
Page 61 of 65
#
Req.
Description
Height
Length
Width
Hole
$/Each
BKM-0905-FM
2
0.905
0.438
$38
0.85
0.438
$38
1.142
0.625
$38
0.75
2.5
0.625
$38
1.102
16mm
$38
0.787
16mm
$38
0.608
0.625
$38
1.89
16mm
$38
1.00
2.5
0.625
$38
0.38
0.750
$38
1.163
0.625
$38
1.750
0.625
$38
BKM-0910-FM
BKM-1014-FM
BKM-1015-FM
BKM-1016-FM
BKM-1017-FM
BKM-1018-FM
BKM-1019-FM
BKM-1020-FM
BKM-1021-FM
BKM-1022-FM
BKM-1025-FM
1&2
Page 62 of 65
#
Req.
Description
Height
Length
Width
Hole
$/Each
BKM-1026-FM
2
1.77
2.5
0.625
$46
0.79
2.5
0.625
$46
0.79
0.625
$46
1.102
0.625
$46
0.25
15
0.688
$54
1.05
2.5
0.625
$38
1.84
2.5
0.625
$38
1.25
0.625
$46
2.00
1/2-13
$54
1.951
M12 x 1.75
$54
3.00
3/8-16
$38
3.00
1/2-13
$38
BKM-1027-FM
BKM-1028-FM
BKM-1029-FM
BKM-1030-FM
BKM-1036-FM
BKM-1037-FM
BKM-1041-FM
BKM-1053-FM
BKM-1057-FM
BKM-1065-FM
BKM-1066-FM
Page 63 of 65
#
Req.
Description
Height
Length
Width
Hole
$/Each
BKM-1067-FM
2
2.91
M12 x 1.75
$38
4.75
3/8-16
$54
3.75
1/2-13
$54
3.701
M12 x 1.75
$54
4.701
M10 x 1.5
$54
12
1/2-13
$77
14.5
12
1/2-13
$225
4.75
14.5
12
1/2-13
$295
1.875
16.1
10.4
M12 x 1.75
$225
BKM-1071-FM
BKM-1072-FM
BKM-1073-FM
BKM-1074-FM
BKM-1080-FM
BKM-1100-FM
BKM-1110-FM
BKM-1210-FM
Page 64 of 65
#
Req.
Description
Height
Length
Width
Hole
$/Each
1.875
16.1
10.4
M12 x 1.75
$225
$131
BKM-1215-FM
0.75
2.5
2.5
10.5mm
$38
1.6
2.5
2.5
10.5mm
$38
1.5
12.5
M12 x 1.75
$108
$174
FTA-0900-SI
FTA-0905-FM
FTA-0910-FM
FTA-0916-FM
2
FTA-1000-SI
1
1.75
1.125
.563
$38
1.049
5.375
15mm
$46
1.102
5.375
15mm
$46
1.84
5.375
15mm
$46
FTA-1010-FM
FTA-1015-FM
FTA-1016-FM
FTA-1017-FM
Page 65 of 65
Goulds
3298
ANSIMAG
K-Series
Finnish Th.
UC Series
Iwaki
MDM,MDFL
INNOMAG
TB-mag
YES
NO
NO
NO
NO
YES
NO
NO
NO
NO
YES
NO
NO
NO
NO
YES
NO
NO
NO
NO
YES
NO
NO
NO
NO
YES
NO
NO
NO
NO
YES
NO
YES
YES
NO
YES
NO
NO
NO
NO
YES
NO
NO
NO
NO
YES
YES
YES
YES
NO
YES
NO
NO
NO
NO
Thrust Balanced
9
9
9
9
9
9
Wear Rings
9
9
9
9
The Patented wear ring system prevents impeller from rubbing containment shell in the
event of a primary bearing upset.
Wear rings control leakage rates maintaining higher efficiencies.
Wear Rings restrict solids > 0.005 from entering the containment shell area, keeping all
bearings and critical flow paths clear.
Concentrations to 30%, particulate sizes to
Open Suction
9
A cantilever shaft supported in the containment shell eliminates the need for a shaft
support in the pumps suction. No suction blockage, Lower NPSHr.
Isolated from the suction pressure by a patented thrust balanced system, the radial
bearings operate in a pressurized fluid environment.
Pressure in the bearing area is approximately 1/3 of TDH which virtually eliminates the
possibility of flashing.
Burst pressures at 3000 psi give the TB-mag pump a 10 x safety factor and resistance to
sudden system surges.
All Innomag casings are designed to minimize radial loads and distribute pressure
evenly across the entire flow range.
Lowers stress on bearings and wear rings maximum pump life.
A patented design combines a simple, yet proven, off-the-shelf dry run cartridge seal
with our long couple bearing frame. Together, these products provide your service with
true metallic secondary containment.
Quality Assurance
9
9
9
All parts are manufactured to the highest possible standard of quality and workmanship.
All completed pumps and wet ends must pass a 25 point quality inspection including, a
running performance/endurance and pressure test prior to shipping.
All critical components manufactured in house in our US Factory.