Beruflich Dokumente
Kultur Dokumente
: Third
17304
: 100
Time: 3 Hours
Instructions:
1. All questions are compulsory
2. Illustrate your answers with neat sketches wherever necessary
3. Figures to the right indicate full marks
4. Assume suitable data if necessary
5. Preferably, write the answers in sequential order
Q1. (A) Attempt any SIX of the following
12 Marks
08 Marks
a) A load of 5KN is to be raised with the help of a steel wire. Find the minimum diameter of
the steel wire, if the stress is not to exceed 100MPa.
b) A cantilever beam 2 meter long carries a udl of 1.5 KN/m over a length of 1.6 m from the
free end. Draw shear force and bending moment diagram for the beam.
c) A steel wire of 5mm diameter is bend into a circular shape of 5 m radius. Determine the
minimum bending stress induced in the wire. Take E=200GPa.
mpt any FO
OUR of the following
Q2. Attem
16 Maarks
at
strresses and its obliquityy on a plane at 20 0 withh the majorr principle plane.
p
f) A gas cylindeer of internaal diameter 40mm is 5m
mm thick. If
I the tensilee stress in the material
is not to exceeed 30 MPa.. Find the maximum
m
prressure whicch can be alllowed in thhe cylinder.
Q3. Attem
mpt any FO
OUR of the following
16 Maarks
a) A simply sup
pported beaam of span L is subj
bjected to udl
u of w/u
unit length. Draw S.F.
diagram. and B.M. diagrram.
1 m long has
h supportss at its endss A and B .IIt carries a point
p
load of
o 5KN at 3
b) A beam AB 10
m A and a udl of 1KN
N per meterr
meters from A and a pooint load off 5KN at 7 meters from
beetween the point
p
loads. Draw S.F. Diagram annd B.M. diaagram for thhe beam.
c) A cantilever beam 1.5 meter
m
long is
i carrying point loadss 1000N eacch at a distaance of 0.5
meter, 1.0 meeter, and 1.5 meter fro
om the fixedd end. Draw
w S.F. diagrram and B.M
M. diagram
m
foor the cantileever beam.
d) A simply sup
pported righht side oveerhanging beam
b
suppo
orted at 4 meter
m
and right
r
side 1
meter overhanng. A Loadded by udl 10 KN /m ovver entire sp
pan. Draw S.F.
S diagram
m and B.M.
diagram.
e) A simply suppported beam
m of 5 meteer span subjjected to a clockwise
c
moment
m
of 15
1 KN/m inn
e Draw S
S.F. diagram
m and B.M. diagram.
a ddistance of 2 meter from the left end.
f) Fiind M.I. of a square 1000 mm size about
a
their diagonal.
d
Q4. Attem
mpt any FO
OUR of the following
16 Maarks
Q5. Attem
mpt any FO
OUR of the following
16 Maarks
a) A rectangularr beam 60 mm
m wide annd 150 mm deep is sim
mply supportted over a sppan of 6 m.
ximum bending stress
If the beam is subjecteed to central point load 12 KN,, Find max
induced in thee beam secttion.
b) Caalculate the limit of ecccentricity foor a circularr section havving diametter 50 mm.
c) A rectangulaar strut is 150
1 mm an
nd 120 mm
m thick. It carries a lo
oad of 180 KN at ann
o 10 mm inn a plane bisecting the thickness. Find
F
the maaximum andd minimum
m
ecccentricity of
inttensities of stress in thee section.
d) A hallow circcular colum
mn having external andd internal diiameters of 300 mm annd 250 mm
m
c
a verrtical load of
o 100 KN at
a the outer edge of the column. Caalculate the
respectively carries
m intensities of stress inn the sectionn.
maximum and minimum
f
2 carrries a load P=25 KN. The cross section
s
of thhe clamp att
e) A c-clamp ass shown in fig.no
x--x is rectanggular, havinng width equ
ual to twicee the thickneess. Assumiing that thee c-clamp is
made of steell casing withh allowablee stress of 1000N/ mm2.F
Find its dim
mensions.
f)
Fig no.2.
3
Fig no.3.
16 Marks
a) State the equation of torsion and write the notations used in it.
b) A solid circular shaft of 120 mm diameter is transmitting power of 120 KW at 150 rpm.
Find the intensity of the shear stress induced in the shaft. Take Tmax =1.4 Tavg.
c) Find power transmitted by a shaft having 60 mm diameter rotating at120 rpm.If maximum
permissible shear stress =80 MPa.
d) A steel shaft of solid circular section has to transmit 375 KW at 210 rpm. The maximum
shear stress is not to exceed 50 MPa and the angle of twist must not be more than 10 in the
length of 3m. Take G=80GPa.Determine diameter of the shaft.
e) A shaft of hallow circular cross section has outer diameter 120 mm, inner 90 mm It is
subjected to a torsional moment of 18 KN/m. For this shaft compute shear stress at the
outer surface.
f)