Beruflich Dokumente
Kultur Dokumente
SECTION 90 CAB
Chapter 1 Cab Removal
CONTENT
Section
Description
Page
Torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
90 150
90 150
Suspension Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
604.55.111.00 06 2002
TORQUES
SPECIAL TOOLS
Cab Lifting Tool
604.55.111.00 06 2002
295027
CAB REMOVAL.
Removal. (Op. 90 150)
DANGER
Lift and handle all heavy components using lifting
equipment of appropriate lifting capacity. Ensure that
units or parts are supported by suitable slings or
hooks. Ensure that noone is in the vicinity of the
load to be lifted.
Remove the cab from the tractor as follows.
1. Ensure that the tractor is parked on a level
surface.
2. Chock the front wheels using suitable wheel
stops.
3. Detach the negative cable (1) from the battery
and insulate.
2
4. Open and raise the engine hood.
5. Unscrew the retaining screws and remove the
engine side panel (1). Repeat for the right side of
the engine.
3
6. Connect the engine hood to a hoist using a nylon
cable (2). Disconnect the strut (1) repeat for the
right hand side of the hood.
604.55.111.00 06 2002
5
8. Disconnect the lighting harness connector (1).
6
9. Remove the brake fluid supply line (1), and the
connections to the left and right brake lines (2).
7
10. Remove the bolts (1) which retain the engine
hood to the engine frame. Ensure that the hood
is removed without obstructions and that no
other components are interfering.
604.55.111.00 06 2002
9
12. Loosen the retaining nut and detach throttle
control cable from (1) from the injection pump.
10
13. Loosen fittings (1) and (2) and detach air
conditioning hoses.
11
14. Remove rubber mat from cab floor.
15. Remove cab floor panel retaining bolts and
remove panel from cab.
12
604.55.111.00 06 2002
13
17. Detach hydraulic steering oil supply fitting (1)
and steering oil return fitting (2). Mask off the
hoses to prevent contamination entering the
system.
14
18. Jack up the rear of the tractor and place two
suitable stands (1) under the final drive cases in
order that the two wheels are off the ground. If
necessary, detach the lift rods from the lower
links.
15
19. Sling the wheel using a nylon strap (1), unscrew
the retaining nuts and remove the wheel. Repeat
for the other wheel.
16
604.55.111.00 06 2002
20. Loosen the two bolts on the cab roof and fix tool
no. 295027 (1) using two m12 bolts and spacers.
Connect the tool to a hoist and keep lift chains
tensioned.
17
21. Remove the bolts (1) and (2) from the cab pillar,
and detach the transmission and fuel tank
breather tubes. Remove the washer motor
electrical connectors and remove the washer
tank (3) from its bracket.
18
22. From the rear of the remote/electronic draft
control. valve assembly, remove the Rclip x 2
(1) from each remote valve fitted.
23. Loosen the nut (2) and slide the collar over the
cable to expose the pin (3). Remove this pin (3)
to separate cable and valve. Repeat for all
remote valves fitted to the tractor. (Ensure the
Remote valve lever in the cab is in the neutral
position to aid removal.)
19
24. Remove the cab to chassis earth strap (1).
20
604.55.111.00 06 2002
21
26. Remove the circlip withdraw the pin, remove cab
strap (1), replace pin and circlip. Repeat for the
right hand side of the cab.
22
27. Tractors with Cab Suspension
Remove nut and bolt from Panhard rod
assembly. Remove rod from supports.
23
28. Tractors with Cab Suspension
Remove the rubber washer (1), the retaining
washer (2), and the nut (3) from the
damper/spring assembly. Repeat for the right
hand damper/spring assembly.
24
604.55.111.00 06 2002
25
30. If fitted remove the cotter pin and detach creeper
gear control idler lever (1).
26
31. Loosen the retaining nut (1), remove the rclip
(2), and the cotter pin (3) of the hitch release
cable.
27
32. From the handbrake release mechanism,
remove the split pin (1), the cotter pin (2), and the
retaining ring (3). Remove the cable from its
support.
28
604.55.111.00 06 2002
10
29
34. Disconnect connector (1) from the engine
harness to the cab.
30
35. Undo the cab mounting bolt (1) while holding the
nut (3) under the cab floor. Recover the bolt and
washer (2). Repeat for the right side of the cab.
36. Raise the cab slowly, ensure that all cables and
hydraulic hoses are free of obstruction.
37. Place cab on a secure stand.
31
604.55.111.00 06 2002
11
Cab Installation
WARNING
Always use suitable tools to align the cab
components and the transmission. DO NOT USE
HANDS OR FINGERS.
1. Install the cab to the transmission observing the
following points.
Reassembly follows the disassembly procedure in reverse.
Adjust park brake as described in Section 33.
Remove all air from the service brake lines as
described in Section 33.
If fitted adjust the auto pickup hitch release
cable.
Tighten all bolts to specified torque.
Engine coolant check the level and topup
if required.
Adjust cab suspension.
32
604.55.111.00 06 2002
12
604.55.111.00 06 2002
34