Beruflich Dokumente
Kultur Dokumente
Important Installation and Operation information that should be reviewed during the
equipment selection process. Contact the factory with any questions.
The Squeeze Belt is a unique piece of equipment because of its design allows capacity to be maintained up to 38 degrees of incline. With its unique design there are a few installation and operation
requirements that must be reviewed during project review.
Understanding the theory of the Squeeze Belt. The Squeeze belt uses three independent belts to complete its operation.
Feeder House Belt: The Feeder House belt has two functions (both are very important) for optimal
operation of the complete conveyor.
The first function that the Feeder house belt is to bring the product up to the proper speed matching
the main tube belts. This is completed when the product is introduced to the end of the feeder house
belt and carried on the belt until it is discharged at the end. During this travel the product is brought
up to match the speed of the main tube belts 1000 to 1500 ft. (304.80 m to 457.20 m) per minute.
The second function that the Feeder house completes is to position the product between the upper
(top) and lower (bottom) belts. The optimum operating angle between the feeder house and the main
tube is 140 degrees. This operating angle allows the maximum about of product to be placed between
the upper and lower belts in the main tube. If the operating angle is increased between the feeder
house and main tube then the operational capacity of the conveyor will be reduced.
See layout to the right.
Feeder House view of product in reference to the main tube upper and lower belts.
This picture shows the Feeder House Belt in the largest
operating angle. Note how shallow the product depth would be.
When the belt is in this or less than optimal operating angle
140 degrees then product will hit the upper belt and splatter
outside of the machine.
This picture shows the Feeder House belt in the 140 degree
operating angle. Note the full product depth would be. When
The belt is at the optimal operating angle 140 degrees the
product will be placed underneath the upper belt and so grain
splatter will occur outside of the machine.
In the minimum incline angle the clearance requirements will change by the length of
the conveyor. Below is shown at its maximum height and will get closer to grade with
the a shorter length of conveyor.
It is important to always have a second piece of equipment to supply product to the Feeder House of
the Squeeze Belt when unloading from portable equipment
(straight trucks, hopper bottom trailers, end dump trailers or like equipment).
Below are pieces of equipment we offer to supply product to the Feeder House.
Transfer Belt Hopper: The Transfer Hopper can be
used to supply product to a Squeeze Belt. Please
note the measurements in the chart below. The
capacity of the transfer hopper is up to 6000
bushels per hour (162 TPH). Capacity will be the
highest at lower angles of incline.
If a transfer hopper is used the Squeeze belt will
not have the option of reaching its maximum
capacity.
Hutchinson/Mayrath
Squeeze Belt Conveyor Complete with Power Take Off (PTO) Drive
Catalog No.
20350PFB
20450PFB
20600PFB
20700PFB
20901PF
Tube Diameter
10 (25.4 cm)
10 (25.4 cm)
10 (25.4 cm)
10 (25.4 cm)
10 (25.4 cm)
Length
35 (10.67
45 (13.72
60 (18.29
70 (21.34
90 (27.43
m)
m)
m)
m)
m)
3450
3950
6050
6200
7650
Weight
lbs. (1565
lbs. (1792
lbs. (2744
lbs. (2812
lbs. (3470
kg)
kg)
kg)
kg)
kg)
List Price
$26,950.00
29,445.00
36,515.00
38,334.00
49,215.00
Squeeze Belt Conveyor Complete with Electric Motor Drive (Less Motor)
Catalog No.
20350EFB
20450EFB
20600EFB
20700EFB
20901EF
35 (10.67 m)
45 (13.72 m)
60 (18.29 m)
70 (21.34 m)
90 (27.43 m)
25 HP (18.5 kw)
30 HP (22 kw)
40 HP (30 kw)
50 HP (37 kw)
60 HP (45 kw)
3
4
4
4
5
List Price
Optional Equipment
TIRES - Add 8 to Catalog No., i.e. 20700PFB8. For 35, 45 & 60 Models, Add $355.00 to List Price.
For 70 & 90 Models, Add $550.00 to List Price.
Hydraulic hoist power pack; 110 Volt (AC) Electric (8 gallon capacity)
- Catalog No. PP0207 - List Price $2,355.00.
NOTE: For additional accessories, see conveyor accessory pages in this section
2015
Hutchinson/Mayrath
Model
A
11'-10"
35'
(10.67 m)
B
8'-3"
(3.61 m)
(2.51 m)
(13.72 m)
(3.99 m)
13'-1"
9'-5 1/2"
60'
13'-6 1/2"
9'-10"
45'
(18.29 m)
70'
(21.34 m)
90'
(27.43 m)
(4.13 m)
14'-2"
(4.32 m)
16'-3"
(4.95 m)
(2.88 m)
(3.00 m)
10'-5"
(3.18 m)
C
21'-4"
(6.50 m)
D
5'-3"
(1.60 m)
(2.91 m)
25 HP
(2.49 m)
(18.5 kw)
(6.17 m)
(4.14 m)
(2.87 m)
9'-5"
30 HP
32'-5"
6'-4"
36'-5"
24'-8"
19'-11 1/2"
10'-10"
40 HP
28'-0"
23'-5 1/2"
12'-8"
50 HP
14'-8"
60 HP
37'-10"
(11.53 m)
(11.10 m)
6'-6"
42'-3 1/2"
(1.98 m)
(15.84 m)
(2.04 m)
(7.52 m)
(12.89 m)
(8.53 m)
54'-7"
40'-7 1/2"
(16.64 m)
(12.38 m)
13'-7"
8'-2'
POWER
(7.57 m)
(1.93 m)
20'-3"
9'-6 1/2"
OVERALL
TREAD WIDTH
(1.84 m)
(9.88 m)
24'-10"
(5.45 m)
(7.76 m)
(6.08 m)
(7.15 m)
25'-11"
(7.90 m)
(3.30 m)
(3.86 m)
(4.47 m)
(22 kw)
(30 kw)
(37 kw)
(45 kw)
Description
Drive Kit PTO
Drive Kit PTO (f/Gearbox model)
Electric Drive for 35 (10.67 m) (Jack Shaft Drive)
Electric Drive for 35 (10.67 m) (Pulley Shaft Drive)
Electric Drive for 45-70 (13.72-21.34 m) - (Jack Shaft Drive)
Electric Drive for 45 (13.72) - (Pulley Shaft Drive)
Electric Drive for 90 (27.43 m)
Electric Drive for 90 (27.43 m) - (f/Gearbox model)
Electric Drive f/60 & 70 (18.3 m & 21.34 m) - (Pulley Shaft Drive)
Weight
85 lbs. (39 kg)
85 lbs. (39 kg)
235 lbs. (107 kg)
260 lbs. (118 kg)
245 lbs. (111 kg)
270 lbs. (122 kg)
265 lbs. (120 kg)
265 lbs. (120 kg)
270 lbs. (122 kg)
List Price
$ 765.00
695.00
951.00
1,174.00
1,016.00
1,208.00
1,083.00
1,275.00
1,275.00
NOTE: D2135BE, D2145BE, D2160BE and D2091BE include the motor sheave and bushing. All others do not.
0400008
0400009
2015
Hutchinson/Mayrath
POWER REQUIRED:
OWNERSHIP ADVANTAGES:-
2015
Hutchinson/Mayrath
Transport Position
IMPORTANT: Keep all shields and safety devices in place at all times. Observe all safety signs and warnings shown
on the product and in the operators manual. Hutchinson/Mayrath reserves the right to change design and/or specifications
without notice or obligation.
- What belt conveyor length is best?
03381A1
03382A3
0402225
Belt Speed
in FPM
640 FPM (195.07 m)
640 FPM (195.07 m)
640 FPM (195.07 m)
0402226
Capacity
in BPH
6000 BPH
3300 BPH
1750 BPH
2015
Hutchinson/Mayrath
Tube Diameter
10 (25.4 cm)
10 (25.4 cm)
10 (25.4 cm)
Length
60 (18.29 m)
70 (21.34 m)
85 (25.91 m)
Weight
3116 lbs. (1413 kg)
3522 lbs. (1598 kg)
5050 lbs. (2291 kg)
List Price
17,190.00
18,720.00
22,770.00
Add letter C to part no. for Belt Drive instead of Chain Drive, i.e. 10850B15PC.
Add $2,202.00 to List Price.
Catalog No.
10600B15E
10700B15E
10850B15E
Tube Diameter
10 (25.4 cm)
10 (25.4 cm)
10 (25.4 cm)
Length
60 (18.29 m)
70 (21.34 m)
85 (25.91 m)
Elec. Power
Required
15 HP (11 kw)
15 HP (11 kw)
20 HP (15 kw)
No. of
Belts
3
3
3
Weight
3192 lbs. (1448 kg)
3598 lbs. (1632 kg)
5050 lbs. (2291 kg)
List
Price
$17,065.00
18,595.00
22,700.00
Add letter C to part no. for Belt Drive instead of Chain Drive, i.e. 10850B15EC.
Add $2,202.00 to List Price.
Optional Equipment
TIRES - Add 8 to Catalog No., i.e. 10600B15P8. Add $355.00 to List Price.
Hydraulic Hoist Power Pack; 110 Volt (AC) Electric, (3 gallon capacity)
- Catalog No., PP0208 - List Price $2,155.00.
Weight - Pounds
85 lbs. (39 kg)
150 lbs. (68 kg)
List Price
$588.00
645.00
Rubber Belt Option - For operation below 20F (-5C) - Add R to Catalog No. ( i.e. 10600B15PR or 10600B15PCR.)
Add $15.00 per foot of conveyor to List Price, i.e. for 60 (18.29 m) conveyor, add $900.00.
NOTE: For additional accessories, see conveyor accessory pages in this section.
0400482
2015
Hutchinson/Mayrath
- 10'' (25.4 cm) x 12 gauge (2.66 m) galvanized w/full length wind guards
- 15'' (38.1 cm) Rubber continuous chevron pattern with slider backing. (PVC belt is optional.)
RECEIVING HOPPER:
- Low profile transfer hopper style with collapsible spring
supported canvas
DISCHARGE SPOUT:
- Adjustable black plastic with 12 (30.5 cm) round outlet
DRIVE FOR 36 MODEL:
- Drive located at the head end with snub pulley; electric or hydraulic.
DRIVE FOR 50 MODEL:
- Electric S drive mounted in middle of conveyor.
OPERATING SPEED:
- 770 Feet per minute (235 mpm) for electric w/5.2 P.D. motor sheave
CAPACITY:
- Up to 5000 bph (135 tph); on electric drive model
- Up to 4000 bph (108 tph); on hydraulic drive 36 model
HORSEPOWER REQUIRED: - 10 HP (7.5 kw) - for 36 (10.97 m) model and 15 HP (11 kw) for
50 (15.24 m) model.
PRODUCT ADVANTAGES: - Gentle handling to maintain seed quality.
- Exclusive belt alignment guide to maintain belt tracking.
- Capable of handling commodity products. Ideal for receiving from bin
unloaders.
- Spring loaded belt take-up to keep constant tension on conveyor belt.
Length
Weight
36 (10.97 m) 2,290 lbs. (1039 kg)
36 (10.97 m) 2,225 lbs. (1009 kg)
50 (15.24 m) 2,900 lbs. (1315 kg)
50 (15.24 m) 3,080 lbs. (1397 kg)
List Price
13,905.00
15,460.00
17,275.00
18,400.00
*NOTE: If you wish to have the dual (hydraulic and electric) drive capability for the B10362ERW-ES model, order
the D10362H drive also. See page 7.
On the 50 (15.24 m) model, a cogged belt drive option is available instead of the roller chain drive. To order, add
the letter C to the catalog no., i.e. B10500ECR. Add $2,039.00 to the List Price.
PVC Crescent Top Conveyor Belt Option. Omit the R from the Catalog No., i.e. B10362EW or B10500E.
(PVC belts not recommended for operation below 25F.)
Deduct $380.00 from list price for 36 (10.97 m) models and deduct $525.00 from list price for 50 (15.24 m)
models.
To order Hutchinson belt conveyors, add H, i.e. HB10362ERW or HB10500ER.
Mayrath use existing catalog number, as shown above.
NOTE: Electric motor is not included on electric drive models. Motor sheave, bushing and drive key are furnished.
{Use a 10 HP (7.5 kw) motor on the 36 (10.97 m) model and a 15 HP (11 kw) motor on the 50 (15.24 m) model.}
An optional 3.8 P.D. motor sheave & bushing is available on the 36 LPCC, which decreases the belt speed by
approximately 200 feet per minute (60.96 meters per minute). The sheave Part No. is 3097A1 - List Price $32.90.
The bushing Part No. is 3086A1 - List Price $11.20.
An optional motor sheave is not available on 50 (15.24 m) models.
NOTE: The 36 (10.97 m) hydraulic models do not include the hoses from the control valve to the tractor. A hydraulic
drive 50 (15.24 m) model is not available. The 36 (10.97 m) hydraulic models require 15 gpm (57 lpm) @ 1500 PSI
(10342 kPa).
NOTE: The older 36 (10.97 m) seed belt w/o the center take-up assembly can be updated with a center take-up.
Order Catalog No. 10150CTP if the conveyor has a PVC belt; List Price $1,450.00.
Order Catalog No. 10150CTR if the conveyor has a rubber belt; List Price $1,465.00.
2015
Hutchinson/Mayrath
Drive Kits
Catalog No. Description
D10361E
36 (10.97 m) Electric Drive Kit
D10361H*
36 (10.97 m) Hydraulic Drive Kit
D10362H** 36 Hydraulic Drive Kit
D10500P
50 (15.24 m) PTO Drive Kit
D1060BE
50 Electric Drive Kit
Weight
140 lbs. (64 kg)
215 lbs. (97 kg)
100 lbs. (45 kg)
320 lbs. (146 kg)
150 lbs. (68 kg)
List Price
$ 991.00
$ 2,822.00
$ 2,426.00
$ 2,075.00
$ 645.00
* For units prior to Serial Number 928507, use D10360H instead of D10361H.
**If a customer requests to have both an electric and hydraulic drive installed at the same time on a
B10362ERW-ES unit, then order Catalog No. D10362H.
If a customer wants to convert a B10362ERW-ES and install a hydraulic drive and remove the electric drive,
order Catalog No. D10361H.
The change-over kits are for converting from one drive to the other. Electric drive kits do not include the electric
motor. Motor sheave, bushing and drive key are provided.
Hydraulic drive kits do not include the hoses from the control valve to the tractor. Hydraulic drives require 15 gpm
(57 lpm) @ 1500 PSI (10342 kPa).
Optional Equipment
TIRES - Add 8 to Catalog No., i.e. B10362ERW8-ES or B10500ER8. Add $355.00 to List Price.
NOTE: For additional accessories, see conveyor accessory pages in this section.
0400010B1 0401023A
2015
Hutchinson/Mayrath
HORSEPOWER REQUIRED:
OWNERSHIP ADVANTAGES:
03424A1
2015
Hutchinson/Mayrath
03425A1
List Price
$5,150.00
5,150.00
775.00
1,020.00
815.00
186.00
308.00
1,120.00
465.00
566.00
465.00
465.00
485.00
485.00
1,880.00
2015
Hutchinson/Mayrath
OWNERSHIP ADVANTAGES:
- Flat bottom, troughed edges, 10 gauge (3.43 mm), 20 degree inclined angle.
- 24'' (61.0 cm) PVC cresent pattern with slider bed backing, stainless steel
belt splice and pin material.
- Adjustable angle with 16 x 21 (40.6 cm x 53.3 cm) rectangular outlet.
- 5-1/2 (14.0 cm) clearance. 7 x 10 (2.13 m x 3.05 m) wide area. Ramps and
dumping area a single unit.
- S-Drive on cresent face of belt w/spring loaded take-up, lagged
drive pulley. Conveniently located under the incline section.
- Overall from hitch pin to spout end is 33-5 (10.19 m).
- 3 feet 4 inches (10.2 m)
- Hopper sides 10 (3.05 m) long by 12 (30.5 cm) wide. Cable lift into position.
- Rotating arm design using a hydraulic cylinder.
- Electric motor. Power take-off. Hydraulic motor.
- 600-800 feet (182.88 m-243.84 m) per minute
- Up to 10,000 bushels per hour (270 TPH).
- 10 HP (7.5 kw) electric. Hydraulic drive capacity minimum 20 gal./min
(75 liter/min.) @ 1500 PSI (10342 kPa).
- Standard incline section length is 64 (1.63 m). On stationary models,
5 (1.52 m) of additional length may be requested, which provides
20 (50.8 cm) of additional discharge height.
- Low drive-over clearance; only 5-1/2 (14.0 cm) high.
- Extra wide 24 (61.0 cm) belt.
- Smooth transition from horizontal to incline.
- Optional greater discharge height. (Stationary models only)
- Higher capacity with lower belt speeds.
- PTO drive choice.
- Undercarriage lift choices.
- Receive from side dump wagons, as well as bottom dump and
rear dump vehicles.
- S type drive on return belt for greater drive efficiency and lower
belt tension requirements. Includes snub pulley to give greater
wrap at drive pulley for slip free operation.
- Spring loaded belt take-up for lower operating belt tensions.
- Guide roller assembly to keep belt tracking properly.
- Walk across platform and handrail provided to cross conveyor.
- Adjustable angle discharge spout.
- Removable hitch tube.
- Self cleaning wing type tail pulley.
- Product surface area - 17-1/2 (44.7 cm) wide .
- Hopper shield dump width - 42-1/2 (1.08 m).
10
2015
Hutchinson/Mayrath
Drive
Type
24245E
* 24245EH
24245H
24245HV
24245P
24245N
Electric
Electric
Hydraulic
Hydraulic
PTO
None
Undercarriage
Lift Type
Hydraulic Cylinder
Hydraulic Cylinder
Hydraulic Cylinder
Hydraulic Cylinder
Hydraulic Cylinder
Hydraulic Cylinder
List
Price
Weight
3870
3950
3670
3700
3720
3640
lbs.
lbs.
lbs.
lbs.
lbs.
lbs.
(1755
(1792
(1665
(1678
(1687
(1651
kg)
kg)
kg)
kg
kg)
kg)
$22,480.00
24,690.00
23,505.00
24,260.00
22,435.00
21,710.00
NOTE: On electric drive models (24245E), a hydraulic hand pump is provided for operation of the lift cylinder and a
winch is provided to raise and lower the hopper panels.
*The 24245EH electric drive model has a hydraulic power unit in place of the hand pump and winch.
(Requires 230/460V, 3 PH, 50/60 Hz.)
To order Hutchinson belt conveyors, add H, i.e. H24245E, Mayrath use existing Catalog No., as shown.
NOTE: The optional control valve kit is provided on the 24245HV models.
TIRES - Add 8 to Catalog No., i.e. 24245E8. Add $355.00 to List Price.
NOTE: On electric drives, the motor is not furnished. Motor sheave, bushing and drive key are furnished.
A 10 HP (7.5 kw) 1750 RPM motor is required. (NOTE: For power recommendations on extended length stationary
units, see page 12.)
On hydraulic drives, the hoses to the hydraulic motor are not furnished. (See optional control valve kit on page 12.)
On hydraulic lift undercarriages, the hoses to the cylinder are not provided. (See optional control valve kit on page 12.)
For numbers listed without drive, select the desired drive from the options on the next page.
0400069A
11
2015
Hutchinson/Mayrath
STATIONARY OPTIONS
Catalog
No.
25243L00
25243L05
25243L10
2524A
Description
List
Price
Weight
2400 lbs.
(1089 kg)
2690 lbs.
(1220 kg)
2960 lbs.
(1343 kg)
20 lbs.
(9 kg)
$16,030.00
17,550.00
19,060.00
334.00
For these conveyor catalog numbers, select the desired drive from the table below.
Discharge heights given are from bottom of main frame. (Not from top of pit.)
DRIVE KITS
Catalog
No.
Description
D2420E Electric drive kit (2-Belt)
D2421E Electric drive kit (3-Belt) for units with extended incline section
D2422E Electric drive kit (2-Belt) includes hyd. hand pump for axle lift
(For portable units after Serial No. 919561)
D2420H Hydraulic drive kit
D2420P PTO
Weight
140 lbs. (64 kg)
150 lbs. (68 kg)
175 lbs. (79 kg)
List
Price
$ 770.00
790.00
1,610.00
1,990.00
685.00
Electric drive kit does not include motor, but does include motor sheave. {Use 5.0 (12.7 cm) P.D. 2 or 3-groove sheave.}
For 25243L00 & 25243L05 models, a 10 HP (7.5 kw) 1750 RPM motor is required.
For 25243L10 models, a 15 HP (11 kw) 1750 RPM motor is required. {Use 5.0 (12.7 cm) P.D. 3-groove sheave.}
On hydraulic drive models, an optional control valve kit is available, which provides all hoses, fittings and valves to completely
plumb the conveyors hydraulic system. NOTE: Does not include hoses from hydraulic power source to conveyor. To order
specify catalog no. 2424H. List price is $840.00.
.
NOTE: For additional accessories, see conveyor accessory pages in this section.)
PP0209 Hyd. Power Unit Retrofit Kit - List Price $2,200.00. (For Serial No. 918764 and higher.) (230/460V, 3PH, 50/60 Hz)
0400758
12
2015
Hutchinson/Mayrath
CONVEYOR ACCESSORIES
Dolly Wheel Kits
Catalog
No.
Squeeze
Belts
2015D
2115D
Squeeze
Belts
2115DR
Single
Belts
2014D
Conveyor
Lengths
Weight
35 & 45
(10.67 m & 13.72 m)
60, 70 & 90 (Hand Lever Style)
(18.29 m , 21.34 m & 27.43 m)
60, 70 & 90 (Ratchet Jack Style)
(18.29 m, 21.34 m & 27.43 m)
60, 70 & 85
(18.29 m, 21.34 m & 25.91 m)
90 lbs.
(41 kg)
125 lbs.
(57 kg)
130 lbs.
(60 kg)
80 lbs.
(36 kg)
List
Price
$ 995.00
$1,500.00
$1,905.00
$ 935.00
Single Belt
Dolly Wheels
Squeeze Belt
Dolly Wheels
Discharge Diverter
Catalog
No.
Squeeze
Belts
0400285
0400286
2100DD
Conveyor
Lengths
Weight
35 thru 90
(10.67 m thru 27.43 m)
13
70 lbs.
(32 kg)
List
Price
$ 800.00
2015
Hutchinson/Mayrath
CONVEYOR ACCESSORIES
Arc Axle Kits (Hub Mount Style)
Catalog
No.
Squeeze P3075A
Belts
P3074A
Conveyor
Lengths
List
Price
Weight
35, 45 & 60 (10.67m, 13.72m & 18.29 m) 294 lbs. (134 kg)
70 x & 90 (21.34 m & 27.43 m)
294 lbs. (134 kg)
$2,300.00
$2,375.00
Add: $ 710.00
Hub Mount
Arc Axle Kit
Volts
Phase
A2031B1
230/460
A2031B2
230/460
Weight
Fit on
60, 70 & 85 (18.29m, 21.34m & 25.91m)
Single Belt or
35, 45, 60, 70 & 90 (10.67, 13.72m, 18.29 m,
21.34 m & 27.43)
Squeeze Belt
List
Price
$ 3,001.00
2,539.00
0401864
Catalog
No.
2424S
Weight
190 lbs.
(86 kg)
14
List
Price
$2,333.00
2015
Hutchinson/Mayrath
CONVEYOR ACCESSORIES
Spout Liner Kit for Squeeze Belt Conveyor
Catalog No.
N6402
Description
Weight
List Price
Spout Liner
15 lbs. (7 kg)
$197.00
Description
Weight
1015AS-Set
1024AS-Set
List Price
$260.00
$450.00
Includes the correct components for four belt connections, but no installation tool.
(NOTE: to order the Belt Splice Installation Tool, specify Part No. 1030704. List Price - $409.00
(NOTE: to order the Hand Skiver Tool, specify Part No. 1035075. List Price - $51.90.
Skiver is used to remove crescents or chevron top at area of splice application.
Staple driver for belt splice. Part No. 1036842. List Price $102.00.
Belt
Width
Repair
Section Length
List
Price
15 (38.1 cm)
3 (91.4 cm)
$250.00
1034961-3 Rubber
15 (38.1 cm)
3 (91.4 cm)
$295.00
1029217-3
24 (61.0 cm)
3 (91.4 cm)
$410.00
1029215-3
Belt
Type
PVC
PVC
0400290
Catalog No.
Weight
List Price
Seed Hopper
A1015H
$315.00
Support Stand
A1015HS
$305.00
15
2015
Hutchinson/Mayrath
CONVEYOR ACCESSORIES
SQUARE TO ROUND DISCHARGE SPOUT ADAPTER
For use on 36 & 50 LPCC Conveyors
and on the 60, 70 & 85 Single Belt Conveyors.
This adapter makes it possible to connect an 8 flex spout to the existing discharge.
Catalog
No.
N6412
List
Price
Weight
12.5 lbs. (6 kg)
$ 120.00
0400284
List
Price
Weight
22 lbs. (10 kg)
16
$ 510.00
2015
Hutchinson/Mayrath
BELT:
- 15'' (38.1 cm) PVC crescent pattern with slider bed backing.
NOTE: A rubber belt option is available for low temperature
operation {below 20 (-5 C)}
DRIVE:
HORSEPOWER:
LENGTH:
BELT SPEEDS:
CAPACITIES:
DISCHARGE SPOUT:
FEATURES:
To select the basic horizontal custom belt conveyor, the following must be determined.
1. The length of conveyor required.
2. The incline angle, if any, of the conveyor.
3. The desired capacity in bushels per hours. (Charts are based on dry corn.)
From the horizontal custom belt conveyor catalog number table, select the catalog number for the
desired conveyor length. NOTE: The last three numbers of the catalog number designate the nominal
pulley center length of the conveyor in feet.
From the motor selection chart for the appropriate incline angle (0, 5 & 10 degrees given), find a length
of conveyor longer than the conveyor length required. Use the lowest conveyor belt speed that will give
the desired capacity. For instance, using the zero degree incline table for a 101 foot (30.78 m) long
conveyor that will handle up to 3300 bu/hr (89 tph), select the 131 foot (39.93 m) length. This will
determine the motor horsepower that will provide the capacity and belt speed for the conveyor length
{7-1/2 HP (5.5 kw) at 400 FPM (12.2 mpm) for this example}. From the drive catalog number table,
select the catalog number for the selected motor horsepower and belt speed. The drive list price is
found at the bottom of the horizontal custom belt conveyor catalog number table.
Both a conveyor catalog number and a drive catalog number must be ordered.
NOTE: In cases where the conveyor will always operate at capacities (bu/hr) lower than those listed in
the motor selection chart, it may be possible to go with somewhat longer lengths. In such cases, consult
the factory for recommendations. In no case, will conveyors longer than 131 (40 m) be provided.
17
2015
Hutchinson/Mayrath
0400733
18
2015
Hutchinson/Mayrath
For the optional gated inlet, order Catalog No. UB01001 and specify quantity desired. (Wt. 47 lbs.)
List Price is $210.00 each.
For the optional collapsible canvas inlet hopper, order Catalog No. UB01002. (Wt. 22 lbs.)
List price $375.00.
For Rubber Belt, add R to conveyor catalog number, i.e. UB150016R. Add $15.00/ft. of conveyor,
i.e., add $240.00 for UB150016R. (For operation below 20 F.)
In conveying applications where inadvertant stoppage or slowing down of a conveyor may damage
the conveyor or upstream equipment feeding it, there is a speed monitoring device available.
Consult factory for pricing and information. To prevent damage due to a plugged discharge chute
or spout, there is a plugged chute device available. Consult factory for pricing information.
0400734-2
19
2015
Hutchinson/Mayrath
0400735
20
2015
Hutchinson/Mayrath
040113
21
2015