Beruflich Dokumente
Kultur Dokumente
2) Checking In Car
When entering the car cabin important thing to check is the condition of rubber clutch pedal,
brake and gas. Everything must be installed properly and not thin.
Then, check your car's hand brake as well, especially the lever and penguncinya. Everything
must be in condition and functioning properly.
3) Sitting Position
There are 3 important things that will we get if we are correct sitting position, namely:
a) Communication
Easy to communicate with other riders and monitor the situation outside the car.
b) Leisure
Not easily tired and always alert even if driving long distances.
c) Control
Easy to feel the early symptoms when the car starts to lose balance. So that it can be
anticipated.
To get the proper sitting position follow the procedures in the event:
Seat belt
Always use seat belts as a primary safety protective equipment. Make sure the sound of
CLICK!, When installing it.
The use of proper seat belt, must pass through the shoulder and hip bones. Use the height of
the seat belt to sit right.
Distance Chairs
Adjust the distance of your chair so you easily operate the gas pedal, brake and clutch.
Seat backrest
The position of chair should be comfortable, not too tall but not too gentle.
Distance Body Steering
Distance ideal body with a steering wheel that is about 25cm. How to measure it, put both
your wrists at 12. Then set the back of the chair.
Retaining Position Head
Place the back of the head parallel to the height of the head.
Steering Altitude
Adjust the height of the steering to feel comfortable to drive.
Once seated comfortably, check the following:
Checking Instruments Dashboard
Check all indicators on the dashboard when the key in the ON position. For vehicles
equipped with ABS and SRS airbag, make sure that when turning the car off the indicator.
4) Sports Steering
The position of the hands of the most appropriate basis while driving the left hand at 9
o'clock position and right hand at 3 o'clock position. Position your thumb should be vertical
to the steering wheel and steering wheel does not go into the circle.
Avoid the habit of driving with one hand, palm of the hand and driving with your fingers into
the wheel rim. Besides easy to lose control when driving a car, you are also in danger of
injury or even death.
In the meantime, BA is useful to increase braking power when brake suddenly. This
mechanism works based on the speed of the brake pedal in an emergency. So with a little
stamping but fast, the car can stop quickly.
6) Scanning
When he was driving a car, need to pay attention to all road users or road conditions around,
such as motorcycles, cars, signs, pedestrians or other important objects that can affect
(RPM).
For example, technical data on the manual written book Maximum torque: 200 Nm/3.750
rpm. This means that the highest moment of 200 Nm occurs at the time of rotating machines
as much as 3750 per minute.
In this example, means you should make the shift gear when the rpm shows the range of 3750
numbers.
Figures RPM on tachometer is also important to note not only when the change gear to a
higher position. To streamline fuel consumption, while speeding down the road Keep the
engine speed in the range of the maximum torque. Because, that's when fuel supply is in
accordance with the output of machinery and manpower needed to drive the car.
Extend Vehicle Age
1. Avoid warming the engine are too long, if the average spin machine has run the vehicle.
2. Round cultivated machine do not be too low and not too high.
3. Avoid running the vehicle at high speed, try to run the vehicle with constant speed and do
not mengkocok-whipped on the accelerator when not needed.
4. When driving do not put a foot on the clutch pedal
5. Keep your tire pressure according to vehicle / right.
6. For vehicles using Exhaust Brake, position the main switch to ON if you're driving.
7. Follow the maintenance of the existing maintenance schedule on pedomn book owners and
book service.
1. For the first 1,000 km of vehicle must be run in ways that special or so-called running-in.
2. Read the manual carefully run a vehicle provided by the manufacturer and execute when
running the vehicle.
3. Before running the vehicle, Heat engine first, do not run a vehicle with a sudden, do not
hold acceleration and do not brake suddenly.
4. Do not work on the engine rev too high. We recommend that you labored to spin machine
is always lower than 60% of maximum engine speed.
5. After the vehicle undergoing the first 10,000 km, replace the engine lubricating oil, and
filter
6. After undergoing vehicle 10,000 km, there is the possibility of bolt-bolt became loose. So
bring your vehicle to the garage for inspection and dikokohkan bolts and screws. Also check
the free slit valve.
7. Know your vehicle well before you start your vehicle at high speed because each vehicle
has unique characteristics, especially in terms of security and safety in travel.