Beruflich Dokumente
Kultur Dokumente
The request of Photovoltaic products is very high. The configuration of solar lamps, the solar panels'
installation perspective and the capacity proportion of batteries and the controller's SOC controlling charge
is directly related to the system's efficiency and service life ,so it must make the price according to the
latitude and longitude where the product used and the power consumption that how many hours per day
and how many rainy days can be assured so that to assure the configuration. It is not right that many
factories quote you without asking. We Soundsest would configure and quote you according to the latitude
where your system played and the power consumption that how many hours per day and how many rainy
days can be assured, so that it could meet your system's working requirement, which is the most optimal
and economic.
The conditions which must be provided when the solar street light designed
1. Where the solar street lights use(detailed to the city)how about the solar radiation?
2. The light source optical and the load power.
3. The height of the light pole and the width of the street.
4. How many hours needs the system work?
5. If it is cloudy and rainy day how many days need the system continue to work?
Configuration
Configuration items
Solar Panel
Material
Parameters
Monocrystalline
Silicon Module
Lifespan
Warranty
Remarks
25years
15years
Sharp silicon
10years
5years
Germany
Wind generator
Light source
special
maintenancefree Pbacid batteries
SD-400W or SD800W
LED Lamp (CREE LED)
20years
100,000hrs
2years
5years
Germany
Controller
Lamp pole
Programming digital
controller
Steel with galvanized
15years
25years
1year
*
Surface Treatment
Ambient Temp
Wind Resistibility
Working time
Battery
4)Package
the weight after packaging(kg) 20kg
Net Weight (kg) 16kg
Package Size (cm) 1106020
Have used single chip and special software, realized intelligent control, computer control, dual input,
protecting of anti-joint and anticharge protection, over charge protection , over discharge protection,
overload protection, light control + time control, delay, voltage and current detection status indicators,
temperature compensation. Series PWM charging the main circuit, accurate discharge control, timing
control sperm and industrial-on-chip, one button operation, the controller circuit board import APL three
defenses paint handling, moisture resistant, and a DC output, or 1 HZ output.
7.5*2A
12V;24V/12V AUTO
1.25 rated load current 60 seconds . 1.5 rated loads current five
seconds
8 mA
Less than 0.2V
Less than 0.1V
-25 to +55 ,Military is not the same
14.4V;28.8V
13.6V;27.2V
-2.5 mv/ /2V ,(boost charge ,direct charge, float charge, charge
return voltage
10.8V;21.6V
13.2V;26V
PWM charge mode
SD85
DC24V (AC110240V)
3WX32PCS
96W
13W
30W
60W
85W
8W
15W
25W
35W
1500LM
3000LM
5500LM
8000LM
104-114
4700K-6300K
8M 30LUX
(10M 22LUX)
135-90 Degree
35m x 15m
IP65
670x200x100
mm
760x300x230
mm
11KG
Input Voltage
LED Particles
Approved Power (W)
The actual power
consuption (W)
The energy-saving
mode power
consuption (W)
Power source
efficiency (LM)
Light efficiency
(LM/W)
Color Temp
Vertical angle of
ilumination LUX
LED perspective
Irradiation area
Grade of protection
104-114
4700K-6300K
104-114
4700K-6300K
104-114
4700K-6300K
4M 26LUX
135-90 Degree
18m x 8m
IP65
Lighting Dimensions
300x200x100 mm
Package Size
Weight
760x300x230 mm
8KG
8M 25LUX
135-90 Degree
28m x 10m
IP65
450x200x100
mm
550x300x230
mm
7KG
8M 27LUX
135-90 Degree
28m x 10m
IP65
670x200x100
mm
760x300x230
mm
11KG
Instructions
1Generally speaking, this product should use with the solar charge and discharge controller together.
Please make sure your solar charge controllers output be DC24V. Please contact the solar charge
controllers output link point with the power input (DC24V, in,"+","-") link point as the instructions on the shell
of this product. Please note positive and negative polarity, if contact with the opposite side, it will result in
launching the protection mechanisms and burning the fuses.
2Please follow the instruction on the shell of the product, contact the LED light source with the output link
point .(LED, out ,"+","-"). Please note the negative also.
3Output mode and time settings: This product has two output modes, and a total of 13 hours divided into
10 of the set time. The first time period is 40 minutes and others are 80 minutes for each.
4When the solar charge and discharge controller to detect the weather has been dark, at the beginning of
output, the product begins to count the time. if you expect the output to be the efficiency enhanced mode,
please refer to the first switch on Time down (hi) .The first time is 40 minutes, and if you want a second time
80 minutes also for the high-efficiency enhanced mode, please Timer the second switch down, but if you
want to change the mode into PWM for energy-saving mode, switch for upward (lo). And so on, you are free
to choose for each time of the output mode.
5Linked by the above instructions, switch the power to "on", the system will start operation automatically
6This product only used to control LED lighting pattern, there is no the solar charging and discharging
controller as general, which is the protection mechanisms for the battery on over charge or over discharge.
If not with the use of solar charge controller, connect directly to the battery of this product, the product of
lighting control functions can use also. However, because the batteries can not be protected, the entire
group of solar street lighting system might have been damaged.
Optical properties
Curve like a bat wing, and each section will vary because of the need, not identical, the control of light
reasonable makes the distribution to a rectangular spot. The installation height of 10 m, the spot was 36 * 16
m rectangular, and the out -efficiency in the effective exposure area is more than 70 percent ,the total
transmission rate is more than 90%, on the maximum degree ,reduces the loss of light, makes the LED's
light fully utilized;In the effective exposure to the region is very uniform illumination, evenness of more than
0.5, higher than the highest levels of the national standard of road lighting 0.4;Light-edge clear, effective
radiation outside the region without adverse glare, can not cause light pollution, is the ideal cut-off-type
lamps;Meet the requirements reasonable of path lighting or other special lighting, can be widely applied to
lighting field with special requirements such as road lighting, advertising , is a green, energy-saving,
environmentally friendly lighting products
Optical properties
Light Curves
Lighting horizontal position
Optical properties
Optical properties
Effect light source high 9m road width 25m light 36 m spacing
Attentions
The installation and maintenance of solar street lamps must be qualified by a corresponding companies
and technical staff
Do not use the parts without the manufacturer's recommended , or else the system may cause damage or
danger
All the solar lights devices during the installation process should not scratch, butt;
Do not place inverted the battery in the transport, installation process and humid and the exposure to
sunlight;
Do not short-circuit lines connecting the various (at the negative exposure);
System Connection order: load - the battery - solar panels
System demolition order: battery - solar panels - load
Install solar panels must move to south, you'd better use the compass
All the screws should be tightened, can not be loosened, reliable connectivity ;
Threads, pay attention the wire connections be not clamping in the joint of the light pole Wire connections,
should be firmly connected, and with PVC tape wound.
DO not Smoking or firing at the installation area, for there is a small amount of hydrogen when the
batteries used, it would be an explosion if meets the fire;
Because of a lighting system is a separate work units, a slight difference in time to tune on/off lights is
normal
Please every six months clean the dust on the battery components, but DO not water rinse bottom-up .
Comparison of Spectra
For eyes: at the same illumination, LED street light is 2.5times than sodium lamp.
Spectra-efficiency Function
The retina is the radiation receiver composed by cone cells and rodshaped cells.
Two cells have entirely different nature and functions. The photographic ability of cone cells are poor than
the rod-shaped , but they had different feelings to the shade. When bright lighting (daytime), visual (the
vision) the cone cells play a role only, when the weak lighting (night), visual (dark vision) mainly plays a role
by the rodshaped cells . The human eye spectral response of the different wavelengths of the sensitivity is a
function of wavelength, call it spectrum-efficiency function. Experimental surface, do not observe the dark
field at the same time, spectral-efficiency function is slightly different. International Commission on
Illumination (CIE) determine the spectrum-efficiency function in Figure (a), from the map ( ) can be seen
that the visual () and the dark vision '() between the peaks corresponding to different wavelengths,
() peak in the 555 nm, and '() peak in the 507 nm.
Experimental surface, do not observe the dark field at the same time, spectral-efficiency function is slightly
different. International Commission on Illumination (CIE) determined the spectrum-efficiency function in
Figure ( ), from the map (a) can be seen that the visual () and the dark vision '() between the peaks
corresponding to different wavelengths, () peak in the 555 nm, and '() peak in the 507 nm.
For the same spectral distribution, under the conditions of visual and dark vision brightness, there is an
obvious difference.In Figure ( ), the brightness of LED lights dark vision is 2.35 times than the visual , and
the dark vision of sodium lamp brightness is 0.94 times than vision Usually optical measurement equipment
to the photographic visual conditions, and the lights is for night lighting (dark visual conditions), so it needs
amend the data if use the general illumination subject for test , LED lights that coefficient of 2.35, sodium
lamp correction factor for the 0.94. Therefore, under the same conditions of intensity (measured by
equipments), LED lights is 2.5 times lighter than the high-pressure sodium lamp. Accordingly, to achieve the
same brightness, LED illumination of street lamps only 40 percent of high pressure sodium lamp can be.
INSTALLED WORKS