Beruflich Dokumente
Kultur Dokumente
Abstract:The paper describes a network that has been intended for context sensing,
especially for activity monitoring of a patient. It consists of multiple
sensors such as heart monitoring, temperature, magnetic field sensors
etc., that are attached to the human body. To access the sensor
information and to make flexible sensor configurations feasible, an
appropriate sensor based Body Area Network (BAN) will be presented. A
combination of wireless and wired technologies is best suited for the
specific application, in terms of robustness, energy consumption, privacy
and integrability into everyday outfits or some wearable platforms. After
introducing the network architecture, the paper describes the platform
developed for wearable context monitoring system.
INTRODUCTION
Context sensing or context awareness is said to be one of the most important
properties of future computer systems. Context awareness can be described as
the ability of a system to model and recognize what the user is doing and what
is going on around him and to use this information to automatically adjust its
configuration and functionality.
One aspect that needs to be addressed in order to realize this vision is how
context information can be obtained. It is obvious, that a single physical sensor
alone can not provide enough information to characterize the users situation.
Therefore, the use of multiple heterogeneous sensors, distributed over the
users body. These simple sensors provide relevant information on the users
situation. The challenges arising from this approach are manifold
a) The management of multiple, distributed sensors in a common framework.
b) To interconnect the sensors, an adequate Body Area Network BAN) is
required.
The communication channels within such a network can be either completely
wire-based, wireless or a mixture of both. The network may have static or
dynamic, single-path or multi-path routing algorithms with a flat or a
hierarchical topology. For the network a hierarchically structured topology that
reflects the anatomy of the human body is used. See Fig.(a), providing a logical
separation of sensor data.
hospital phase of patient care: here, wireless sensors could simplify patient
transport while providing a constant stream of vital-sign information to a
mobile computer on which a paramedic or emergency medical technician (EMT)
could capture additional patient information. The integrated vital sign
and patient care data could then be relayed to a hospital ahead of the patient,
so that physicians and nurses could better anticipate the patients needs.
Mass casualty incidents (MCIs) are unexpected situations in which large
numbers of casualties are generated over a short period. In most cases, only
about 10 to 15 percent of survivors are severely injured; however, quickly
identifying and stratifying these patients from among the less severely injured
survivors poses a unique set of challenges. Deployment of small, wireless vitalsign sensors in a sensor network could assist first responders in monitoring
and deciding which patients would benefit most from transport to a dedicated
trauma center and, conversely, which patients could be safely either excluded
or delayed entry into this system. The sensors and sensor network architecture
would allow aggregate patient information to be transmitted to a centralized,
decision support system, so that a global view of any mass casualty situation
could be gained and a greater semblance of order could be established.
fig(b):Network Architechture..
Furthermore, the system should be able to dynamically remove and add
sensors, just as certain pieces of clothing are removed and added during the
day. Both requirements can be very well satisfied using wireless technologies.
They provide an easy solution to dynamically interconnect the sensors into the
wearable system without user interaction. Assuming that a single piece of
clothing has multiple sensors incorporated, providing a wireless link for any of
the sensors is not an optimal solution concerning interference with or
from other wearable systems, required hardware resources and energy
consumption. Furthermore, in general the usage of wireless communication
links brings up concerns about health side-effects and privacy issues since
personal data can be more easily intercepted by others. The use of a hybrid
solution that combines wireless with wired technologies can overcome
these drawbacks.
This network incorporates this hybrid solution and additionally groups the
sensors into logical units reflecting the anatomy of the human body. This
results in a hierarchical topology. For example, motion sensors which are
integrated into a pair of trousers may build a single sub network --- or two
different sub networks as in Fig (a} to provide independent information
about the motion of the two legs --- and thus reflecting the anatomy of the
human body. Sensors in a sub network are connected by a wired bus.
Communication between those sensors is handled by a dedicated sub networkmaster. The wired connection allows for high data rate while being insensitive
to electrical interference. In addition, since there is only one RF link for each
sub network and not for any sensor, hardware resources are cut down and
power consumption is reduced. This wired connection also provides a means to
share a common power source between the sensors in a sub network.
Furthermore, it is much less sensitive concerning privacy issues. Another
advantage of this design is based on the idea that a sub network-master not
only gathers the data from the connected sensors, but also preprocesses it
in order to extract only relevant information. This allows for a reduction in the
amount of data that has to be transmitted to a central master. This is specially
the case if multiple sensors contain redundant information. Conductive textiles
which are part of the clothing itself may be used to interconnect the nodes
rather than normal insulated copper wires. Fig. 1c illustrates a prototype where
the cables of the sub network bus are replaced by conductive textile bands.
Each sub network is connected wirelessly to the central master. Adequate
network protocols ensure that sub networks in different parts of the users
outfit can be dynamically connected to the central master when they are put on
or taken off without the user being directly involved.
IMPLEMENTATION
This section focuses on the wireless part of the network and gives a short
overview of our hardware platform used for wearable context monitoring and
the corresponding wireless protocols.
A. Hardware Nodes
1) Overview: The requirements for the hardware of the central master and its
slaves are: low-power operation, low hardware complexity and minimum
software overhead but at the same time being flexible for different applications
and different combinations of sensors. The modules should be small to allow
realistic context monitoring. Considering the application of the nodes, a
transmission range of approximately one meter is sufficient. Higher
transmission ranges require higher transmission powers thus increasing
power consumption which should be avoided. Fig. a shows the schematics of
such a node. The main task of the slave nodes is to provide a wireless
bidirectional link for interconnecting the different sub networks to the central
master and a wired link to the master-module of the sub network (see Fig.(b)).
Data from the sensor sub network is gathered by the slave nodes, prepared for
transmission (framing, coding) and transmitted to the master upon request.
Furthermore the nodes provide power to the connected sensors. The design
allows the hardware to run both in master and in slave mode.
needed to transmit a one byte packet and thus the transmitter can transmit
11.52 kByte/s of data. Manchester coding or 12 bit coding would further
decrease this number by a factor of 2 or 2 3 respectively.
Clearly, if only a few data bytes are transmitted, the protocol overhead
dominates. The doted line shows the worst case for protocol B where the
master assigns time slots that can hold 127 bytes of data ( d = 127) but only ld
bytes are transmitted. The solid black line shows the best case for protocol B,
in which the master has an a priori knowledge about the size of the data
packets from the slaves and assigns time slots that match this size ( d = ld).
3) Comparison of the two Protocols: Protocol A is to be preferred if we expect
irregular sized data packets, alternating intervals between polling different
slaves and frequently changing slaves that need to be addressed. In context
recognition this is especially useful when only sensor information from a
certain body part (e.g. only arms) needs to be retrieved. Protocol B has the
advantage that the receiver part of the slaves can be powered down once they
are initialized, while in protocol A the slaves need to listen continuously if they
dont want to miss a request from the master. Thus, protocol B helps to reduce
power consumption of the slaves. As a drawback, protocol B can only gain a
high throughput if the size of the data packets is constant and known before
assigning the time slots. The choice of protocol depends mainly on the
requirements given by the application that uses the context information.
CONCLUSION
We have presented a network for interconnecting multiple, distributed bodyworn sensors for context sensing. The use of wired and wireless
communication channels as well as the hierarchical network architecture has
been discussed and motivated by the requirements of our specific application:
integration of the sensors into the users outfit, low power consumption, low
interference with other systems, privacy, and efficient usage of hardware
resources. Apart from the network architecture, an implementation of an
experimental hardware platform has been presented. Future work will focus on
miniaturization of the network nodes and optimization of the protocols.
REFERENCES
1. Foster KE. Radiofrequency Field Surveys in Hospitals. Biomedical
Instrumentation and Technology
2. Barbaro: Biomedical Instrumentation & Tech (2000)
3. Fraunhofer Gesellschaft, Body area network, 2002. [Online]. Available:
http://www.ban.fraunhofer.de
4. H.junker and M stagger WEARNET Ubiquitous Computing
5. A. Tanenbaum, Computer Networks, 4th ed. Prentice Hall PTR, 2003.