Beruflich Dokumente
Kultur Dokumente
Page 1 of 12
Table of Contents
Chapter 5 Data Configuration
5.1 About This Manual
5.2 Introduction
5.3 Displaying the Data Configuration Window
5.4 Configuring the Board Data
5.4.1 Configuring the Clock Board in the Slot 0
5.4.2 Configuring the Clock Board in the Slot 12
5.4.3 Configuring the LCIM Board
5.4.4 Configuring TSOU Board
5.4.5 Configuring the CCOU Board
5.4.6 Configuring TDRV Board
5.5 Configuring the Reference Source
5.5.1 Adding a Reference Source
5.5.2 Configuring Digital Signal Reference Source
5.5.3 Configuring Analog Signal Reference Source
5.5.4 Loading the Reference Source
5.6 Configuring System Parameters
List of Tables
Table 5-1 SRCU or SOCU board parameter
Table 5-2 LCIM board parameter
Table 5-3 TSOU board parameter
Table 5-4 CCOU board parameter
Table 5-5 Digital signal reference source parameter
Table 5-6 Parameter for setting the threshold of the majority vote
Table 5-7 SSM parameter
Table 5-8 Transport parameter
Table 5-9 Analog signal reference source parameter
Table 5-10 System parameter
Describes
5.2 Introduction
5.2 Introduction
There is no BITS configuration data on the maintenance terminal of the SYNLOCK V3. After an NE is selected and the data configuration window is displayed, the
maintenance terminal downloads the configuration data from the BITS. In this way, the data on the maintenance terminal can be consistent with that on the BITS.
You can also query the BITS configuration data through the data configuration window.
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Procedure
Step
1
Action
Double click the Data configuration node on the navigation tree to display the Select NE dialog box.
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Page 2 of 12
Step
Action
Select an NE, and click OK to display the Data configuration-Board Position Diagram dialog box as shown below.
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Procedure
Step
Action
In the Data configuration-Board Position Diagram dialog box, right click the slot 0 in the main frame, and select Add SRCU or
Add SOCU.
Select the configured board, right click and select Load SRCU.
Description
The type of the satellite card. The options are:
l
l
l
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Parameter
Page 3 of 12
Description
The test template for the input channel.
l
test template of
input channel
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Procedure
Step
Action
In the Data configuration-Board Position Diagram dialog box, right click the slot 12 in the main frame, and select Add SRCU
or Add SOCU.
Double click the type field, and select the desired type of the satellite card (here, take GPS as an example) to display a dialog
box as shown below.
It is recommended that to set Visual satellite threshold to 1, and set Satellite mask angle to 5.
10
Select the configured board, right click and select Load SOCU.
11
II. Prerequisite
Before the operation, make sure that:
l
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Page 4 of 12
III. Note
To configure the test template, note that:
In the standard template mode, the threshold point and value cannot be modified.
If the value input does not meet the requirement or is the same as another one, you must modify the value according to the system prompts.
l
l
IV. Procedure
Step
1
2
Action
In the Data configuration-Board Position Diagram dialog box, right click a slot from 110, and select Add LCIM.
In the confirmation dialog box that appears, click OK.
The new board is displayed in the corresponding slot.
Select the LCIM board, right click and select Configure LCIM to display the Configure LCIM dialog box as shown below.
Double click the drop-down list of the MTIE/TDEV test template of channel, and select Wander tolerance or Wander generation
(here, take the Wander tolerance as an example) to display a dialog box as shown below.
Query the threshold point and threshold value of the template, and click OK.
Double click the drop-down list of MTIE/TDEV test template of channel, and select Customize to display the Customize dialog
box as shown below.
l
l
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Page 5 of 12
Step
Action
In the confirmation dialog box that appears, click OK.
The procedure of configuring the FREQ test template is the same as that of configuring the MTIE/TDEV test template. The
difference lies in that there are only Standard template and Customize.
10
11
12
13
14
15
Select the configured board, right click and select Load LCIM.
16
V. Parameter description
Table 5-2 describes the parameters for configuring the LCIM board.
Table 5-2 LCIM board parameter
Parameter
Description
The type of the LCIM board. The options are:
Output mode
l
l
Channel type
Test template of
channel
Test channel
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Procedure
Step
1
2
Action
In the Data configuration-Board Position Diagram dialog box, right click a slot ranging from 110, and select Add TSOU.
In the confirmation dialog box that appears, click OK.
The new board is displayed in the corresponding slot.
Select the TSOU board, right click and select Configure TSOU to display the Configure TSOU dialog box as shown below.
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Page 6 of 12
Step
Action
Click Configure Uniformly to display a dialog box as shown below.
The channels can be configured one by one or uniformly.
10
11
Select the configured board, right click and select Load TSOU.
12
Description
The type of the TSOU board. The options are:
l
Output mode
l
1+1: The active and the standby boards send the signal
at the same time
1:1: Only the active board sends the signal
1:1 is recommended.
The type of the channel 120. The options are E1, 1 MHz,
2048 KHz, 5 MHz and 10 MHz.
Channel type
You can set the type as required. You can also set the
channels of the same output board to the same type for a
convenient management.
Channel blocking
Channel name
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Procedure
Step
1
2
Action
In the Data configuration-Board Position Diagram dialog box, right click a slot ranging from 110, and select Add CCOU.
In the confirmation dialog box that appears, click OK.
The new board is displayed in the corresponding slot.
Select the CCOU board, right click and select Configure CCOU to display the Configure CCOU dialog box as shown below.
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Page 7 of 12
Step
Action
Click Configure Uniformly to display a dialog box as shown below.
The channels can be configured one by one or uniformly.
10
11
Select the configured board, right click and select Load CCOU.
12
Description
The type of the TSOU board. The options are:
l
Output mode
l
1+1: The active and the standby boards send the signal
at the same time
1:1: Only the active board sends the signal
1:1 is recommended.
The type of the channel 120. The options are CC, E1, 1
MHz, 2048 KHz, 5 MHz and 10 MHz.
Channel type
You can set the type as required. You can also set the
channels of the same output board to the same type for a
convenient management.
Channel blocking
Channel name
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Note
To configure the expansion frame, note that:
Up to two expansion frames can be configured on the SYNLOCK V3 BITS.
Only the TDRV, TSOU and CCOU boards can be configured in the expansion frame.
You can directly add the TDRV board to the slot 0 or 12 of the expansion frame and need no configuration.
l
l
l
IV. Procedure
Step
Action
In the pane that appears, right click the slot 0 or 12, and select Add TDRV.
In the confirmation dialog box that appears, click OK.
II. Prerequisite
Before the operation, make sure that:
l
l
III. Procedure
Step
Action
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Step
Page 8 of 12
Action
Select Configuration > Reference Source from the main menu to display a dialog box as shown below.
& Note:
l
Right click the blank area, and select Add Reference Source to display a dialog box as shown below.
Select the desired reference source, as shown in the following figure, and click Ok. If you select the PPS or SSR reference
source, the system prompts that no reference source type should be configured.
& Note:
l
l
l
l
CSSR1 stands for the SSR reference source of the clock board in slot 0.
CSSR2 stands for the SSR reference source of the clock board in slot 12.
CSCLK1CSCLK4 and C1PPS stand for the input reference sources of the clock board.
CLCIM1-1CLCIM1-8 and CLCIM2-1CLCIM2-8 stand for the input reference sources of the LCIM board.
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Procedure
Step
1
Action
Select Configuration > Reference Source from the main menu.
In the reference source list, select the digital signal reference source, right click, and select Configure Reference Source to
display the Reference Source dialog box as shown below.
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Page 9 of 12
Step
Action
If Take part in the majority voting is set to Y, click Majority Voting to display a dialog box as shown below.
10
11
12
13
14
15
Description
The name of the reference source. You can set the
name as required.
Specifies whether set the reference to the active
one. The options are Y and N.
B e ca u se t h e d e vi ce g e n e r a ll y wo r k s i n t h e
intelligent mode, select N.
The level of the reference source. The value range
is 123.
This parameter is set according to the engineering
design and must be unique.
Specifies whether to set the reference source to be
involved in the majority voting. The options are Y
and N.
Y is recommended.
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Page 10 of 12
Parameter
Description
Table 5-6 lists the parameter for setting the threshold of the majority vote.
Table 5-6 Parameter for setting the threshold of the majority vote
Parameter
Description
The threshold of the frequency deviation for the majority
vote of the reference source.
S e le ct o r I n p u t t h e
Threshold
Table 5-7 describes the parameters for configuring the Synchronization Status Message (SSM).
Table 5-7 SSM parameter
Parameter
SSM Information
Description
Specifies whether the signal has the SSM. The options
are Y and N.
Set the parameter as required.
Description
The threshold of the Frame Alignment Signal (FAS). It is
recommended to set this parameter to 65535.
FAS threshold
FAS is involved in the
control
OOF threshold
BPV threshold
CRC threshold
AIS threshold
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Procedure
Step
1
Action
Select Configuration > Reference Source from the main menu.
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Page 11 of 12
Step
Action
In the reference source list, select the analog signal reference source, right click, and select Configure Reference Source to
display the Reference Source dialog box as shown below.
Description
The name of the reference source. You can set the
name as required.
Signal name
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Procedure
Step
1
Action
Select Configuration > Reference Source from the main menu.
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014
Page 12 of 12
Step
Action
In the reference source list, right click a record, and select Load Reference Source, or right click the blank area, and select
Load All Reference Sources.
II. Prerequisite
Before the operation, make sure that:
The maintenance terminal software is installed.
You have logged in to the system and BITS as a maintainer or an administrator.
l
l
III. Procedure
Step
Action
Select Configuration > System Parameter from the main menu to display a dialog box as shown below.
Click Exit.
Description
Specifies the work mode of the system. The options are
MAN and INT, indicating the manual mode and intelligent
mode respectively. It is INT by default.
Specifies whether to set the majority voting result to be
involved in the control. The options are Y and N.
Y is recommended.
Specifies whether to set the SSM to be involved in
selecting source. The options are Y and N.
Y is recommended.
Specifies the position of the SSMB in the E1 signal. The
value range is 48, indicating SA4SA8. It is SA4 by
default.
Set this parameter according to the opposite device
requirement.
S p e c if ie s t h e R e f e r e n c e I n d ic a t o r ( R EF ) f o r t h e
performance test. The signal can be the system input
signal, local vibrating signal of the clock board or the
output signal of the active clock board.
The output signal of the active clock board is select by
default. That is, CSCLKOUT.
Frame format of
output E1
Analog transparent
transmission signal
selection
Select E1
Transparent
Transmission Signal
http://127.0.0.1:52199/hedex/pages/31180917/03%20(2009-08-14)/31180917/03%20(... 22/09/2014