Beruflich Dokumente
Kultur Dokumente
instructions and the procedure, and precautions in the Repair Manual applicable for the model year.
(IG)
* Malfunction symptoms of the SRS are difficult to confirm, so the DTCs become the most important source of
information when troubleshooting. When troubleshooting the SRS, always inspect the DTCs before disconnecting
the battery.
* When the negative (-) terminal cable is disconnected from the battery, the memory of the clock and audio system
will be cleared. So before starting work, make a record of the contents in the audio memory system. When work is
finished, reset the audio systems as they were before and adjust the clock. Some vehicles have power tilt
steering, power telescopic steering, power seat and power outside rear view mirror which are all equipped with
memory function. However, it is not possible to make a record of these memory contents. So when the work is
finished, it will be necessary to explain it to your customer, and ask the customer to adjust the features and
reset the memory. To avoid erasing the memory in each system, never use a back-up power supply from outside the
vehicle.
(IG)
7. 5A
MET
7. 5A
IGN
1 2D
8 2B
A5
Airbag Sensor
(Front LH)
21
A6
Airbag Sensor
(Front RH)
D1
DLC3
B-O
* Work must be started more than 90 seconds after the ignition SW is turned to the "LOCK" position and the
negative (-) terminal cable is disconnected from the battery.
(The SRS is equipped with a back-up power source so that if work is started within 90 seconds from disconnecting
the negative (-) terminal cable of the battery, the SRS may deploy. )
C8
Combination
Meter
A/B
11
SIL
7
-SL
TC
13
+SL
-SR
+SR
2
IF1
IF1
IF1
B-W
BR-W
21 2Q
W-R
22 2Q
* Never use SRS parts from another vehicle. When replacing parts, replace with new parts.
BR
B-O
P-B
* Even in cases of a minor collision where the SRS does not deploy, the following parts should be inspected;
R-Y
B-Y
SRS
* Before repair, remove the airbag sensor if shocks are likely to be applied to the sensor during repair.
IF1
28 A
30 A
27 A
29 A
+SL
-SR
+SR
IJ1
PP5 C
1 2B
1 A
2 A
1 A
2 A (LHD)
1 B
2 B
1 B
2 B (RHD)
2 2B
Pretensioner
32 A (*4)
18 2D
9 2D
W-B
F/PS
W-B
32 G (*5)
E10(G), E13(A)
Engine ECU
A15
Airbag Squib
(Steering Wheel Pad)
W-B
ID
IE
(*3)
(*3)
Y-B
(*3)
IL1
2
Spiral
Cable
PP+
4 C
(*1)
PD1 B
(*3)
IL1
PD+
2 B
W-B
W-B
(*1)
W-B
21 2O
P3 A
Y-B
P+
4 A
(*2)
E2
26 A
(*2)
3 2B
E1
25 A
Y-R
Y
5 2O
GSW2
22 A
(*2)
Y-B
D6 A
B-Y
12 B
D+
5 A
B-Y
10 A
J22(A), J23(B)
Junction Connector
LA
14 A
Y-G
-SL
(*2)
IG2
Y-B
21 A
TC
B-W
15 A
* If the vehicle is equipped with a mobile communication system, refer to the precaution in the IN section of the
Repair Manual.
16 A
SIL
* After work on the SRS is completed, check the SRS warning light.
BR-W
B-Y
* Information labels are attached to the periphery of the SRS components. Follow the instructions of the notice.
4 2B
W-R
* Use a volt/ohmmeter with high impedance (10 k/V minimum) for troubleshooting electrical circuits of the system.
7 2B
BR
20
P-B
22
* If the following parts have been dropped, or have cracks, dents and other defects in their case, bracket,
and connector replace with new one.
* For the purpose of reuse, never disassemble and repair the following parts.
A23
Airbag Squib
(Front Passenger's
Airbag Assembly)
F21(A)
Front Seat
Outer Belt
(LH)
F22(B)
Front Seat
Outer Belt
(RH)
Pretensioner
F22(A)
Front Seat
Outer Belt
(RH)
F21(B)
Front Seat
Outer Belt
(LH)