Beruflich Dokumente
Kultur Dokumente
STUD
Thickness of 0.84, 1.2, 1.6 &
2mm in required cut size with service slots,
as per design & requirement
EDGE ANGLE
92.2
92.2
92.2
101.6
101.6
101.6
152.4
152.4
152.4
203.2
203.2
203.2
41.4
50.8
63.5
41.4
50.8
63.5
41.4
50.8
63.5
41.4
50.8
63.5
Shape
TRACK
Thickness of 0.84, 1.2, 1.6 &
2mm in required cut size with services slots,
as per design
& requirement
96.8
106.2
157
ANGLE
207.8
258.6
309.4
63.5
63.5
63.5
63.5
63.5
63.5
1.6
1.6.1
PART
2.1
2.1.1
2.2
2.2.1
2.2.2
2.2.2.1
with a view to assess the complaint satisfaction and suitable preventive measures taken.
Certification
On the basis of assessment given in Part 3 of this Certificate & subject to
the conditions of certification, use & limitations set out in this Certificate
and if selected, installed & maintained as set out in Part 1 & 2 of this
Certificate, the sections covered by this Certificate are fit for use set out in
the Scope of Assessment.
CERTIFICATE HOLDERS TECHNICAL SPECIFICATION
General
The PAC holder shall manufacture these sections in accordance with the
requirements specified in the relevant Standards. In addition it shall follow
the Company standards specifying requirements of various materials used
in the manufacture of these sections (see Part 5)
Specifications for the System
Specification
The manufacturer shall only use the raw materials supplied with the
relevant documents as laid down in the prescribed Quality Assurance
Plan. The raw materials shall be subject to agreed controls and tests by
the manufacturer before acceptance.
Technical Specifications
Raw materials
1. Stud & track profiles shall be manufactured from pre-galvanized high tensile steel conforming to IS 277:1992,
350 having Yield stress of min.350 MPa & Tensile stress of min. 380 MPa
and coating of min. Z 275 or equivalent as per the Performance
requirement, Dimensions and Permissible tolerances shall to ASTM C:95507. See Fig 2 and table 3
(i) Track shall be formed in a U-shaped configuration, having a depth
Dimension
Item
Length
Web width
Structural Stud
(mm)
+ 2.38
-2.38
+ 0.79
- 0.79
Flare overbend
Hole
centre width
Hole
centre length
Crown
Camber
Bow
Twist
+1.59
-1.59
+1.59
-1.59
+6.35
-6.35
+1.59
-1.59
0.79
12.7 max
0.79
12.7 max
0.79
12.7 max
Structural Track
(mm)
+ 12.7
-
6.35
+0.79
-3.18
+0
-2.38
NA
NA
+1.59
-1.59
0.79
12.7 max
0.79
12.7 max
0.79
12.7 max
Screw
Size
Minimum Shank
Diameter
Minimum Head
Diameter
0.738
No. 8
1.449
0.855
No. 10
1.728
Pullout Capacity
1.10mm
0.84mm
1.10mm
1098
738
423
1183
796.5
490
out Capacity
0.84mm
324
378
S. No. Name
1
2
3
4
5
&
address
of
the customer
200 (approx.)
550 (approx.)
550 (approx.)
S.No
Acceptance Norms
ASTM C1513
Erection
IS 277:1992
Erection
A-1.2
Screws
A-1.3
Anchor
Bolts
A-1.4
A-1.6
Roof Sheets
/Cladding
Corrugated
Sheets
Weld mesh
A-1.7
Insulation
Erection
A-1.8
Cement
Fiber Board
Gypsum
Board
Floor Tiles
Erection
Erection
Erection
Dimensions
Visual
Visual
Visual
Dimensions
Visual
ASTM C955:07
A-1.5
A-1.9
A1.10
A-2 Process
A-2.1
Roll
Framing
A-2.2
Packing
A-2.3
Dispatch
A-2.4
Assembly
HILTI /BTC
Frequency of testing
Level (i)
MTC 100%
Level (ii)
Dimension - 100%
MTC 100%
Dimension - 100%
Visual 100%
MTC 100%
Visual - 100%
Dimension - 100%
Visual 100%
MTC 100%
Visual - 100%
Dimension - 100%
MTC 100%
Dimension - 100%
MTC 100%
Dimension - 100%
MTC 100%
Dimension - 100%
MTC 100%
Dimension - 100%
MTC 100%
Dimension - 100%
MTC 100%
Dimension - 100%
Dimension 100%
Visual - 100%
Visual - 100%
Visual - 100%
Dimension 100%
Visual - 100%
Dimension - 100%
Visual - 100%
Visual - 100%
Visual - 100%
Dimension - 100%
Visual - 100%
180