Beruflich Dokumente
Kultur Dokumente
5
Cdigo de mquina: D104/D106
Manual de Servicio
Diciembre, 2010
Sea prudente cuando tenga que levantar o mover la mquina. Si la mquina pesa mucho, pueden
ser necesarios dos o ms tcnicos del cliente para mover la mquina sin causar lesiones (distensiones
musculares, lesiones de columna, etc.) o daos a la mquina si se cae o se vuelca.
El personal que circule o trabaje cerca de la mquina deber llevar en todo momento la indumentaria
y calzado apropiados. No lleve nunca ropa holgada, accesorios (corbatas, jersis amplios, pulseras,
etc.) ni calzado informal (zapatillas, sandalias, etc.) cuando levante o mueva la mquina.
Antes de trasladar el producto, desenchufe siempre el cable de alimentacin de la fuente de
alimentacin. Antes de trasladar el producto, disponga el cable de alimentacin de forma que no
caiga debajo del producto.
Alimentacin
Herramientas especiales
Durante el mantenimiento
General
Dispositivos de seguridad
No retire nunca ningn dispositivo de seguridad a menos que deba sustituirlo. Sustituya siempre los
dispositivos de seguridad de forma inmediata.
No lleve a cabo ningn procedimiento que afecte negativamente al funcionamiento de los
dispositivos de seguridad. La modificacin o retirada de un dispositivo de seguridad (fusible,
interruptor, etc.) podra provocar un incendio y lesiones. Tras la retirada y sustitucin de un dispositivo
de seguridad, pruebe siempre el funcionamiento de la mquina para asegurarse de que est
funcionando de forma normal y segura.
A la hora de realizar cambios de piezas, utilice nicamente los fusibles o disyuntores adecuados
para la mquina. El uso de dispositivos de sustitucin no diseados para la mquina podra provocar
un incendio y lesiones.
Limpiadores orgnicos
Durante el mantenimiento preventivo, no utilice nunca limpiadores orgnicos (alcohol, etc.) distintos
de los que se describen en el manual de servicio.
Antes de usar cualquier limpiador orgnico, asegrese de que la habitacin est bien ventilada.
Utilice los disolventes orgnicos en cantidades pequeas para evitar aspirar sus vapores, que podran
provocarle nuseas.
Apague el dispositivo, desenchfelo y djelo enfriar antes de realizar el mantenimiento preventivo.
Para evitar un incendio o explosin, nunca utilice un producto de limpieza orgnico cerca de ningn
componente que genere calor.
Lvese bien las manos despus de limpiar piezas con un producto orgnico para evitar la
contaminacin de alimentos, bebidas, etc., lo cual podra provocar enfermedades.
Limpie el suelo por completo despus de derramar accidentalmente aceite de silicona u otro material
para evitar superficies deslizantes que podran provocar accidentes con lesiones en las manos o
piernas. Utilice un limpiador de aceite de silicona "My Ace" (o trapos secos) para absorber el
producto derramado. Para ms detalles, consulte el boletn tcnico Eliminacin de aceite de
silicona (A024-50).
Pilas de litio
Sustituya siempre una batera de litio en un circuito impreso (PCB) por otra del mismo tipo indicada
para el uso en ese circuito. Si se sustituye una batera de litio por otra de un tipo distinto al indicado
para el uso en el circuito, podra producirse una explosin o daos en el PCB.
No deseche nunca las pilas usadas mezclndolas con el resto de la basura. Squelas del lugar de
trabajo y deschelas de acuerdo con la legislacin y la normativa locales pertinentes.
Filtros de ozono
Sustituya siempre los filtros de ozono en cuanto acabe su vida til (segn se describe en el manual
de servicio).
Se puede acumular una cantidad excesiva de ozono alrededor de las mquinas que utilizan filtros
de ozono si no se sustituyen en el momento indicado. Un exceso de ozono puede provocar que el
personal que trabaja alrededor de la mquina no se sienta bien.
objeto, como la pata de una mesa. Un cable de alimentacin enrollado puede hacer que se acumule
un calor excesivo y provocar un incendio.
Asegrese de que el espacio en torno a la fuente de alimentacin est libre de obstculos para poder
desenchufar el cable de alimentacin con rapidez en caso de emergencia.
Asegrese de que el cable de alimentacin est conectado a tierra en la fuente de alimentacin con
el cable de masa del enchufe.
Enchufe el cable de alimentacin directamente a la fuente de alimentacin. No utilice nunca un cable
de extensin.
Al desconectar el enchufe de la fuente de alimentacin, tire siempre del enchufe, nunca del cable.
Deseche siempre los elementos usados (revelador, tner, cartuchos de tner, tambores OPC, etc.)
de acuerdo con la legislacin y la normativa locales pertinentes.
Para proteger el medio ambiente, no tire nunca este producto ni cualquier tipo de consumible a la
basura domstica. Lleve estos elementos a uno de nuestros distribuidores o a un centro de recogida
autorizado.
Devuelva los tambores de selenio usados al centro de servicio tcnico para tratarlos de acuerdo con
la poltica de la empresa para el reciclaje y la eliminacin de residuos.
Asegrese de que todos los usuarios tengan acceso a un manual de instrucciones del aparato.
Confirme que los usuarios han ledo y comprendido todas las instrucciones de seguridad descritas
en las instrucciones de uso.
Mustreles cmo apagar la alimentacin y desconectar el enchufe (tirando del enchufe, no del cable)
si se produce uno de los casos siguientes: 1) se derrama algo en el producto; 2) es necesario realizar
tareas de mantenimiento o reparacin del producto; 3) la tapa del producto est daada.
Prevenga a los usuarios acerca de la extraccin de los elementos de sujeccin del papel de la
mquina. Debe evitarse que caigan en la mquina clips de papel, grapas o cualquier otro objeto
metlico.
Trabaje con cuidado cuando elimine atascos de papel o sustituya botellas o cartuchos de tner para
no derramar el tner en la ropa o en las manos.
Si inhala el tner, haga grgaras inmediatamente con grandes cantidades de agua fra y vaya a
una zona bien ventilada. Si hay indicios de irritacin u otros problemas, acuda a un mdico.
Si se mancha la piel con tner, lvese inmediatamente con jabn y agua fra corriente.
Si le entra tner en los ojos, enjuguelos con agua fra corriente o colirio. Si hay signos de irritacin
u otros problemas, consulte a un mdico.
Si ingiere tner, beba grandes cantidades de agua fra para diluir el tner ingerido. Si hay signos
de cualquier problema, consulte a un mdico.
Si derrama el tner en la ropa, lave inmediatamente el rea afectada con jabn y agua fra. No
utilice nunca agua caliente. El agua caliente puede provocar que el tner se fije en los tejidos de
manera permanente.
Almacene siempre los consumibles de tner y revelador, como paquetes, cartuchos y botellas de
tner y revelador (incluido el tner utilizado y los cartuchos y botellas vacos) fuera del alcance de
los nios.
Almacene siempre los consumibles de tner nuevos o los cartuchos o botellas vacos en un lugar
fresco y seco que no est expuesto a la luz solar directa.
Eliminacin de tner
No intente nunca quemar tner, tner usado o recipientes de tner vacos (botellas o cartuchos). Si
quema el tner, ste podra explotar y esparcirse, provocando quemaduras graves.
Envuelva siempre el tner usado y los cartuchos y botellas de tner vacos en bolsas de plstico para
evitar derramar el tner. Respete la legislacin y la normativa locales pertinentes.
Lleve el tner y los cartuchos de tner usados a uno de nuestros distribuidores o a un centro de
recogida autorizado. Deseche siempre los cartuchos y botellas de tner usados de acuerdo con la
legislacin y la normativa locales pertinentes.
Seguridad lser
El organismo norteamericano Center for Devices and Radiological Health (CDRH: Centro de Dispositivos
y Salud Radiolgica) prohbe la reparacin de unidades pticas lser fuera de las instalaciones del
fabricante. La unidad de carcasa ptica slo se puede reparar en la fbrica o en un centro que disponga
del equipo exigido. El subsistema del lser puede ser sustituido sobre el terreno por un ingeniero cualificado
para la asistencia al cliente. El chasis del lser no se puede reparar en las instalaciones finales. Por lo
8
tanto, los ingenieros de asistencia al cliente tienen instrucciones de remitir todos los chasis y subsistemas
lser a la fbrica o al almacn cuando sea necesario sustituir el subsistema ptico.
El uso de controles, el ajuste o la ejecucin de procedimientos distintos a los especificados en este
manual pueden dar lugar a una peligrosa exposicin a la radiacin.
Alimentacin a lo largo
LEF
Alimentacin a lo ancho
Marcas comerciales
Microsoft, Windows y MS-DOS son marcas comerciales registradas de Microsoft Corporation en los
Estados Unidos y/o en otros pases.
PostScript es una marca comercial registrada de Adobe Systems, Incorporated.
PCL es una marca comercial registrada de Hewlett-Packard Company.
Ethernet es una marca comercial registrada de Xerox Corporation.
PowerPC es una marca comercial registrada de International Business Machines Corporation.
Otros nombres de productos se utilizan en este documento nicamente con fines identificativos y pueden
ser marcas comerciales de sus compaas respectivas. No nos hacemos responsables de los derechos
relacionados con dichas marcas.
10
CONTENIDO
Advertencias importantes sobre seguridad......................................................................................................1
Responsabilidades del tcnico......................................................................................................................1
Antes de la instalacin, mantenimiento........................................................................................................1
Durante el mantenimiento..............................................................................................................................3
Despus de la instalacin, mantenimiento...................................................................................................5
Instrucciones especiales de seguridad para el tner..................................................................................6
Instrucciones de seguridad para este equipo..............................................................................................7
Seguridad lser..............................................................................................................................................8
Smbolos, abreviaturas y marcas comerciales..............................................................................................10
Marcas comerciales....................................................................................................................................10
2. Instalacin
Requisitos de instalacin..................................................................................................................................33
Entorno..........................................................................................................................................................33
Nivel de la mquina....................................................................................................................................34
Requisitos de espacio del aparato.............................................................................................................34
Requisitos de alimentacin..........................................................................................................................35
Combinaciones de unidades opcionales.......................................................................................................36
Opciones del aparato.................................................................................................................................36
Opciones del controlador...........................................................................................................................37
Instalacin de copiadora................................................................................................................................38
Tomas de corriente de los perifricos........................................................................................................38
Diagrama de flujo de la instalacin...........................................................................................................38
Comprobacin de accesorios....................................................................................................................39
Procedimiento de instalacin......................................................................................................................41
11
12
3. Mantenimiento preventivo
Tablas de mantenimiento..............................................................................................................................155
Ajustes de las piezas de PM.........................................................................................................................156
Antes de retirar las viejas piezas de PM.................................................................................................156
13
4. Sustitucin y ajuste
Previamente....................................................................................................................................................159
Herramientas especiales...............................................................................................................................160
Ajuste de la imagen.......................................................................................................................................161
Escaneo......................................................................................................................................................161
ARDF...........................................................................................................................................................163
Registration (Registro)...............................................................................................................................164
Ajuste de borrado de margen..................................................................................................................165
Registro de color.......................................................................................................................................166
Correccin de gamma de la impresora..................................................................................................167
Tapas exteriores.............................................................................................................................................172
Botella de recogida de tner PCDU........................................................................................................172
Puerta delantera........................................................................................................................................172
Tapa de la unidad de limpieza de la ITB................................................................................................173
Tapa izquierda..........................................................................................................................................174
Tapa trasera...............................................................................................................................................175
Tapa inferior posterior..............................................................................................................................175
Filtro de polvo............................................................................................................................................176
Tapa trasera derecha...............................................................................................................................176
Panel de mandos.......................................................................................................................................177
Ajuste de posicin del panel tctil...........................................................................................................177
Tapa derecha interna................................................................................................................................178
Tapa interior...............................................................................................................................................179
Tapa derecha delantera...........................................................................................................................179
Tapa superior derecha ............................................................................................................................180
Marco izquierdo y tapa trasera del marco izquierdo...........................................................................181
Tapa de salida del papel.........................................................................................................................181
Bandeja del inversor.................................................................................................................................182
Bandeja interna.........................................................................................................................................182
Tapa trasera interna..................................................................................................................................182
14
15
16
Cojinete de friccin...................................................................................................................................272
Cambio de tamao de papel...................................................................................................................273
Sensor de fin de papel..............................................................................................................................274
Sensor de registro.....................................................................................................................................275
Sensor de transporte vertical ...................................................................................................................277
Salida de papel.............................................................................................................................................281
Ventilador con solenoide de compuerta de unin.................................................................................281
Unidad de salida del papel.....................................................................................................................281
Sensor de salida de fusin.......................................................................................................................283
Sensor de salida del papel.......................................................................................................................284
Sensor de inversin...................................................................................................................................285
Motor de inversin....................................................................................................................................286
Ventilador delantero de fusin.................................................................................................................287
Unidad dplex...............................................................................................................................................289
Unidad dplex...........................................................................................................................................289
Sensor de entrada dplex........................................................................................................................290
Sensor salida dplex.................................................................................................................................292
Motor de entrada a la unidad dplex.....................................................................................................293
Motor de salida dplex............................................................................................................................294
Motor bypass.............................................................................................................................................294
Unidad de bandeja bypass......................................................................................................................295
Sensor de longitud de papel bypass ......................................................................................................296
Sensor de tamao de papel bypass........................................................................................................297
Sensor de fin de papel bypass.................................................................................................................299
Rodillo de alimentacin bypass...............................................................................................................299
Sensor de posicin inicial de bandeja bypass.......................................................................................300
Componentes elctricos................................................................................................................................301
Circuitos.....................................................................................................................................................301
Tapa de la caja del controlador .............................................................................................................302
Caja del controlador.................................................................................................................................303
BCU............................................................................................................................................................303
HDD............................................................................................................................................................305
Circuito IPU................................................................................................................................................306
17
18
19
Aspectos generales...................................................................................................................................591
Procedimiento............................................................................................................................................591
6. Localizacin de averas
Tablas de SC..................................................................................................................................................597
Condiciones de llamada al servicio tcnico...........................................................................................597
SC1xx: Escaneado....................................................................................................................................600
SC 2xx: Exposicin...................................................................................................................................605
SC3xx: Procesamiento de imagen 1....................................................................................................610
SC4xx: Procesamiento de imagen - 2.....................................................................................................615
SC5xx: Alimentacin de papel y fusin..................................................................................................620
SC6xx: Comunicacin del dispositivo.....................................................................................................634
SC7xx: Perifricos.....................................................................................................................................643
SC8xx: Sistema global.............................................................................................................................650
SC9xx: Varios............................................................................................................................................668
Condiciones de error de control de proceso..............................................................................................673
Resultados de la inicializacin del revelador.........................................................................................673
Resultados de la autocomprobacin de control de proceso................................................................674
Resultado del ajuste de posicin de lnea...............................................................................................677
Gua de solucin de problemas...................................................................................................................679
Calidad de la imagen...............................................................................................................................679
Ajuste de posicin de lnea......................................................................................................................681
Problemas de imagen a intervalos regulares..........................................................................................687
Error de ampliacin de subescaneo........................................................................................................688
Ajuste de imagen trapezoide...................................................................................................................692
Chirrido fuerte procedente de la PCDU..................................................................................................695
Ruido fuerte procedente de la bandeja de papel..................................................................................697
Imagen granulada....................................................................................................................................697
Error de suministro de tner......................................................................................................................707
Solucin de problemas de atascos de papel.........................................................................................708
No hay atascos de papel alimentado desde la PFU.............................................................................722
Configuracin para el modo de papel especial 4, 5 y 6.....................................................................723
Deteccin de atascos....................................................................................................................................734
Presentacin de atascos de papel...........................................................................................................734
20
7. Ahorro de energa
Ahorro de energa.........................................................................................................................................749
Modos ahorro de energa........................................................................................................................749
Eficacia de ahorro de energa.................................................................................................................750
Ahorro de papel............................................................................................................................................753
Eficacia de la funcin dplex/combinar................................................................................................753
NDICE..........................................................................................................................................................757
21
22
23
Configuracin de la mquina
1
Mquina D104/D106
Cdigo de
la mquina
Llama
da
Equipo principal
D104/
D106
[1]
G329
[2]
ARDF
D366
[3]
Bandeja lateral
D427
[4]
tem
24
Notas
[3] es estndar.
-
Configuracin de la mquina
Cdigo de
la mquina
Llama
da
Bandeja de 1
separador
D426
[12]
Bandeja de
desplazamiento
D428
[11]
Finisher interno
D429
[10]
tem
Unidad de
perforacin: 2/3
agujeros
D390-17
Unidad de
perforacin: 2
agujeros
D390-27
Unidad de
perforacin: 4
agujeros
D390-31
Unidad de
alimentacin de
papel de dos
bandejas
D331
Notas
1
Una de las 4 siguientes opciones: slo [10], slo [11], slo
[12], o [11]+[12]
Requiere [10].
[9]
Requiere [10].
Requiere [10].
[6]
Uno de [6], [7] y [8];
El PFU de una bandeja [6] requiere [8].
Unidad de
alimentacin de
papel de una
bandeja
D425
[7]
D448
[8]
Alimentador de
sobres
D559
[5]
tem
Cdigo de la
mquina
Nota
D556
D547
D555
25
G578
Auricular
B433
26
D377-21
Memoria SAF:
Se necesita la opcin de fax.
Slo para el modelo NA: requiere la opcin
fax.
-
B679
D377-01, 02
D377-19
B826
D377-04
Unidad de interface de
contador opcional Tipo A
B870
A674
D556-4, -5, -6
D556-12, -13,
-14
D546
D430-05, 06, 07
Descripcin general
Descripcin general
Disposicin de componentes mecnicos
27
3. 1 carro
4. Sensor de longitud del original
5. Lente
6. SBU
7. Rodillo del inversor
8. Rodillo de salida del papel
9. Compuerta de unin
10. Unidad dplex
11. Unidad de fusin
12. Unidad del PTR (rodillo de transferencia del
papel)
13. Rodillo de registro
14. Rodillo de transporte vertical 1
15. Rodillo de alimentacin bypass
28
Descripcin general
Con opciones
29
Sin opciones
1. Trayecto DF
2. Trayecto de inversin
3. Recorrido dplex
7. Trayecto de salida
30
Descripcin general
7. Embrague de revelado: K
8. Motor de tambor/revelado: K
31
D038/D041
Tarjeta de seguridad
UDF
Opcional
Tarjeta VM
UDF
Opcional
Disponible
No disponible
Funcion de apagado de
seguridad
32
2. Instalacin
Requisitos de instalacin
Entorno
2. Instalacin
Nivel de la mquina
De delante atrs: no se debe sobrepasar 5 mm (0,2")
De derecha a izquierda: no se debe sobrepasar 5 mm (0,2")
Este aparato, que utiliza fuentes de alimentacin de alta tensin, puede generar gas ozono. Una
densidad elevada de ozono es perjudicial para la salud. Por esta razn, el aparato debe instalarse
en una habitacin bien ventilada.
A: Ms de 100 mm (3,9")
B: Ms de 100 mm (3,9")
C: Ms de 315 mm (12,4")
D: Ms de 400 mm (15,7")
Ponga el aparato cerca de la fuente de alimentacin, dejando alrededor los espacios indicados.
34
Requisitos de instalacin
Requisitos de alimentacin
1. Tensin de entrada:
120 V a 127 V, 60 Hz: Ms de 12 A
220 V a 240 V, 50 Hz/60 Hz: Ms de 10 A
2. Fluctuacin permisible de la tensin: 10 %
3. No apoye nada sobre el cable de alimentacin.
35
2. Instalacin
N.
Opciones
Notas
Alimentador de sobres
ARDF (Estndar)
Bandeja de desplazamiento
Bandeja lateral
10
Finisher interno
11
12
Unidad de fax
13
14
15
16
17
18
36
Opciones
IEEE 802.11a/g
IEEE 1284
Bluetooth
Gigabit Ethernet
PostScript 3
PictBridge
Unidad de explorador
Notas
37
2. Instalacin
Instalacin de copiadora
Tomas de corriente de los perifricos
PRECAUCIN
Tensin nominal de los perifricos.
Asegrese de enchufar los cables en las tomas correctas.
[1] ARDF: Conector de asignacin de salida de tensin para accesorio mx. 24V CC
[2] Finisher: Conector de asignacin de salida de tensin para accesorio mx. 24V CC
38
Instalacin de copiadora
*1: Debe instalar primero la bandeja de desplazamiento si quiere instalarla con una bandeja de 1
separador al mismo tiempo.
Comprobacin de accesorios
Compruebe la cantidad de accesorios y el estado en que se hallan.
N.
Descripcin
Canti
dad
Destino
-17, -27
1.
Marcador
2.
3.
-27
39
2. Instalacin
N.
40
Descripcin
Canti
dad
4.
Certificacin
5.
6.
7.
8.
9.
Destino
--17, -19, -21,
-27, -28, -29
-17, -29, -21,
-19
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Suplemento PostScript3
22.
23.
24.
Tapa transparente
25.
-27
Instalacin de copiadora
N.
Descripcin
26.
27.
28.
29.
Canti
dad
Destino
Procedimiento de instalacin
Retire las cintas adhesivas de las unidades de revelado antes de encender el interruptor principal. Si
no quita las cintas, las unidades de revelado pueden sufrir daos graves.
Coloque primero la mquina en la unidad de bandeja de papel si va a instalar una unidad de bandeja
de papel opcional a la vez. A continuacin, instale la mquina y las dems opciones.
Conserve las sujeciones de embalaje despus de instalar el aparato. Puede necesitarlas en el futuro
si transporta el aparato a otro lugar.
Agarre la mquina por los mangos [A] y las asas [B] cuando la levante o la mueva.
41
2. Instalacin
No agarre la mquina por el marco inferior derecho [C] cuando la levante o la mueva. Si lo hace,
podra doblarse el marco inferior derecho [C] de la mquina.
42
Instalacin de copiadora
2. Abra la tapa izquierda del DF [A], y luego retire todas las cintas adhesivas y el retenedor del ADF
si ste se ha instalado.
3. Abra la unidad del ADF y luego retire todas las cintas adhesivas y el envoltorio plstico.
Conserve la tarjeta SD para Java VM y la hoja de etiquetas para el nmero de bandeja y el
tamao de papel. Estos elementos se utilizarn en el paso posterior.
4. Saque la bandeja 1 y 2 [A], y luego retire todas las cintas adhesivas y dispositivos de retencin en
la bandeja 1 y 2.
43
2. Instalacin
44
Instalacin de copiadora
45
2. Instalacin
13. Fije la tapa del mango [A] en el lado delantero de la unidad dplex.
1. Abra la puerta delantera [A] y luego retire la botella de recogida de tner PCDU [B].
46
Instalacin de copiadora
4. Retire todas las cintas adhesivas [A] de las unidades de tolva de tner.
La tapa de la tolva de tner [B] puede retirarse con cinta adhesiva [C].
Asegrese de que se hayan retirado todas las tapas de tolva de tner, cuando se retiren todas
las cintas adhesivas.
47
2. Instalacin
48
Instalacin de copiadora
49
2. Instalacin
13. Presione la botella de tner y luego gire cada una hacia la derecha (en el sentido de las agujas del
reloj).
x 1).
15. Introduzca la tarjeta SD (Java VM) suministrada con los accesorios en la ranura SD 2 [B].
16. Vuelva a conectar la tapa de la ranura de la tarjeta SD (
x 1).
Bandejas de papel
1. Extraiga cada bandeja de papel [A]. A continuacin, ajuste las guas laterales y la gua de tope para
que se ajusten al tamao de papel.
50
Instalacin de copiadora
Para mover las guas laterales, primero extraiga completamente la bandeja. A continuacin,
presione el bloqueo verde situado en la parte posterior dentro de la bandeja.
1. Si no est colocado, instale el emblema correcto [A] y su tapa [B] en la puerta delantera [C] de la
mquina.
Si desea cambiar el emblema que ya est instalado, retire el panel con un objeto (no afilado)
como se muestra [D] e instale el emblema correcto.
2. Pegue en las bandejas de papel [E] las etiquetas adhesivas con el tamao y el nmero de bandeja
correctos.
Las etiquetas adhesivas de tamao y nmero de bandeja de papel tambin sirven para la unidad
de alimentacin de papel y la bandeja de gran capacidad opcionales. Conserve estas etiquetas
para utilizarlas en estas unidades opcionales.
Inicialice el revelador.
1. Asegrese de que el cristal de exposicin o el ARDF est cerrado y que la alimentacin principal
est desactivada.
2. Enchufe la mquina.
51
2. Instalacin
5. Realice el proceso de calibracin de color automtico (ACC) con cada modo (modo de copia,
impresora a 600 x 600 dpi, impresora a 1.800 x 600 dpi e impresora a 1.200 x 1.200 dpi) de la
siguiente manera:
1) Imprima el patrn de prueba del ACC (Herram. usuario > Mantenimiento > ACC > Inicio).
2) Coloque la impresin en el cristal de exposicin.
3) Coloque 10 hojas de papel blanco en la parte superior del grfico de prueba.
4) Cierre el ARDF o la tapa del cristal de exposicin.
5) Pulse Iniciar escaneo (Start Scanning) en la pantalla LCD. La mquina inicia el ACC.
6. Compruebe que la imagen de muestra se ha copiado normalmente.
7. Abra la tapa delantera.
8. Retire la hoja de gua de instrucciones [A] y asegrese de que el informe SMC [B] est almacenado
como se muestra anteriormente. Luego vuelva a colocar la hoja de gua de instrucciones.
52
Funcin
Predeterminado
Instalacin de copiadora
SP5-045-001
"0": Revelados
Funcin
Especifica si el recuento es doble para el papel
A3/11" x 17". Pngase en contacto con su
supervisor cuando tenga que cambiar este ajuste.
Predeterminado
SP5-812-001 a
004
Funcin
Predeterminado
Prepare y compruebe los siguientes puntos de comprobacin antes de visitar al cliente. Si desea ms
informacin, pregunte a la persona clave de @Remote.
Puntos de comprobacin antes de realizar ajustes en @Remote
1. El ajuste de SP5816-201 en la unidad principal debe ser "0".
2. Imprima el SMC con el SP5990-002 y, a continuacin, compruebe si se debe programar
correctamente un ID2 de dispositivo (SP5811-003).
Se deben dejar 6 espacios entre el prefijo de 3 dgitos y el siguiente nmero de 8 dgitos (p. ej.
xxx______xxxxxxxx).
ID2 (SP5811-003) y el nmero de serie (SP5811-001) deben ser el mismo (p. ej. ID2:
A01______23456789 = N. serie A0123456789)
3. Los siguientes ajustes se deben programar correctamente.
Direccin IP del servidor proxy (SP5816-063)
Nmero de puerto del servidor proxy (SP5816-064)
ID del servidor proxy (SP5816-065)
53
2. Instalacin
2. Introduzca el nmero de solicitud que ha obtenido del interface de usuario de @Remote Center y
pulse la tecla [Aceptar] con SP5816-202.
3. Confirme el nmero de solicitud y pulse la tecla [EJECUTAR] con SP5816-203.
4. Compruebe el resultado de la confirmacin con SP5816-204.
Valor
Significado
Satisfactorio
Error de comunicacin
Otro error
5. Compruebe que la pantalla solo muestra la Informacin de ubicacin con SP5816-205, cuando se
ha introducido en la Center GUI.
6. Pulse la tecla [EJECUTAR] para ejecutar el registro con SP5816-206.
7. Compruebe el resultado del registro con SP5816-207.
Valor
54
Significado
Satisfactorio
Ya registrado
Instalacin de copiadora
Valor
Significado
Otro error
55
2. Instalacin
Causa
Cdigo
Significado
-12002
Error de
funcionamiento,
configuracin
incorrecta
Ejecute el registro.
56
Compruebe el estado de la
unidad principal. Si est en uso,
intntelo ms tarde.
Instalacin de copiadora
Causa
Cdigo
Significado
Error provocado
como respuesta de
la GW URL
-2390
-2391
Compruebe el estado de
registro de la unidad principal
-2396
57
2. Instalacin
1. Realice SP 4806-001 para mover el carro del escner desde la posicin inicial. Esto evita que le
entre polvo a la mquina durante el transporte.
2. Asegrese de que no queda papel en las bandejas de papel. A continuacin, fije las placas inferiores
con una hoja de papel y cinta.
3. Siga uno de los procedimientos siguientes:
Ponga cinta de embalaje a las tapas y a las puertas.
Envuelva el aparato con plstico retrctil.
Despus del traslado, ejecute el "Registro automtico de color" como sigue. Esto optimiza el
registro de color.
Realice el procedimiento "Ajuste de posicin de lnea forzado Modo c" (SP2-111-3).
A continuacin realice el procedimiento "Ajuste de posicin de lnea forzado Modo
a" (SP2-111-1).
Para comprobar si SP 2-111-1 fue correcto, mire la pantalla durante el proceso. Al final aparece
un mensaje. Tambin puede comprobar el resultado con el SP 2-194-10 a -12.
Asegrese de que las guas laterales de las bandejas estn colocadas correctamente para evitar
errores de registro de color.
58
Descripcin
Cantidad
Tornillo: M4 x 10
Abrazadera de fijacin
Procedimiento de instalacin
2. Instalacin
60
7. Retire la 1 y 2 bandeja de papel [A] y asegure la unidad de bandeja de papel con dos tornillos
(M4 x 10) [B].
8. Vuelva a instalar todas las bandejas de papel.
9. Aplique las pegatinas de nmero de bandeja de papel y de tamao de papel adecuadas al mango
de cada bandeja.
La hoja de la pegatina de nmero de bandeja de papel y de tamao adecuado est en la caja
de accesorios de la mquina principal.
10. Gire el ajustador [A] hasta que la mquina no pueda empujarse por el suelo.
11. Cargue papel en las bandejas de papel y seleccione el tamao de papel adecuado.
12. Encienda el interruptor principal.
13. Ajuste el registro de cada bandeja (
Ajuste de imagen).
61
2. Instalacin
62
Descripcin
Cantidad
Soporte de fijacin
Procedimiento de instalacin
63
2. Instalacin
La unidad de alimentacin de papel de una bandeja debe estar instalada en la mesa con ruedas
(D448). Prepare la mesa con ruedas primero antes de instalar esta unidad.
64
6. Retire la tapa del conector trasero [A] de la mquina principal (tornillo de remache x 1).
7. Conecte el mazo de cables [B] a la mquina principal.
8. Vuelva a instalar la tapa del conector trasero (tornillo de remache x 1).
9. Retire las bandejas 1 y 2 de la mquina.
10. Apriete los tornillos (M4 x 10) [C].
11. Vuelva a instalar todas las bandejas.
12. Coloque los soportes de fijacin [D] (M4 x 10;
x 1 cada uno).
Ajuste de imagen).
Use SP1002-004
16. Compruebe el funcionamiento de la unidad de alimentacin de papel y la calidad de las copias.
65
2. Instalacin
N.
Descripcin
Pasador
Tornillo escalonado
Procedimiento de instalacin
1. Coloque la mesa con ruedas sobre una superficie plana.
Cantidad
Utilice los orificios de tornillos [A] y [C] si la unidad principal est instalada directamente en la
mesa con ruedas.
Utilice los orificios de tornillos [B] y [C] si la unidad de alimentacin de papel de una bandeja
(D425) est instalada en la mesa con ruedas.
3. Agarre el mango [A] y las asas [B] de la mquina, si la copiadora va a instalarse sobre la mesa con
ruedas.
Cuando levante y mueva la mquina, sujtela por el mango y las asas.
4. Levante la unidad de alimentacin de papel de una bandeja [C] y, a continuacin, instlela sobre
la mesa con ruedas [D].
5. Extraiga la bandeja 2 de la unidad principal o la bandeja de la unidad de alimentacin de una
bandeja.
67
2. Instalacin
2
6. Fije la mquina o la unidad de alimentacin de papel de una bandeja a la mesa con ruedas (tornillo
escalonado x 2)
7. Reinstale la bandeja en la unidad principal o la unidad de alimentacin de papel de una bandeja.
8. Ajuste los cinco ajustadores de nivel de la mesa con ruedas.
68
ARDF (D366)
ARDF (D366)
Comprobacin de componentes
Compruebe, con la lista siguiente, la cantidad y el estado de los componentes.
N.
Descripcin
Cantidad
ARDF
Cartucho de sellado
Perno
Procedimiento de instalacin
69
2. Instalacin
3. Monte el ARDF [A] alineando los orificios para tornillos [B] de la placa de soporte del ARDF por
encima de los pernos.
4. Deslice el ARDF hacia la parte delantera de la mquina.
5. Fije el ARDF con los dos tornillos de rosca manual [C].
70
ARDF (D366)
7. Retire el envoltorio de la hoja del cristal de exposicin [A] y colquela sobre el cristal de exposicin.
8. Alinee la esquina trasera izquierda (de la hoja del cristal de exposicin) con la esquina [B] del cristal
de exposicin.
9. Cierre el ARDF.
10. Abra el ARDF y compruebe que la hoja del cristal de exposicin est correctamente fijada.
71
2. Instalacin
11. Aplique la pegatina [A] en la tapa superior como se indica. Seleccione el idioma que desee.
12. Enchufe la mquina y encienda el interruptor principal; a continuacin, compruebe el funcionamiento
del ARDF.
13. Realice una copia a tamao real. Compruebe que los registros (de lado a lado y de borde anterior)
y la inclinacin de la imagen son correctos. Si no lo son, ajuste los registros y la inclinacin de la
imagen (consulte "Ajuste de imagen").
72
2. Coloque el soporte [B] de la tapa del cristal de exposicin sobre las cabezas de los tornillos salientes
y desplace la tapa [C] del cristal de exposicin hacia la izquierda.
73
2. Instalacin
74
Descripcin
Cantidad
Bandeja lateral
Tornillo: M3x8
Tope de bandeja
Procedimiento de instalacin
x 2).
4. Cierre la unidad de salida de papel de la bandeja lateral [A] y luego conecte el mazo de cables [B]
a la mquina.
5. Instale la unidad de salida de papel de la bandeja lateral (
75
2. Instalacin
x 1: M3x8).
8. Coloque la etiqueta adhesiva Empujar puerta (Push door) [A] en el extremo delantero superior de
la tapa de la unidad dplex.
76
9. Cierre la unidad dplex y coloque la etiqueta adhesiva Empujar (Push) [A] en la tapa de la unidad
dplex.
10. Encienda el interruptor principal de la mquina.
11. Compruebe el funcionamiento de la bandeja lateral.
77
2. Instalacin
Descripcin
Cantidad
Bandeja
Tornillo (M3 x 8)
Procedimiento de instalacin
x 1).
x 1).
79
2. Instalacin
x 1).
x 1: M3x6 azul,
x 1).
80
81
2. Instalacin
Descripcin
Unidad de bandeja de desplazamiento
Cantidad
1
Procedimiento de instalacin
82
x 2).
83
2. Instalacin
x 2).
84
Comprobacin de componentes
Compruebe, con la lista siguiente, la cantidad y el estado de los componentes.
N.
Descripcin
Cantidad
Finisher interno
Unidad de inversin
Tornillo: M3x10
Tornillo: M3x6
12
Ral gua
Tapa izquierda
85
2. Instalacin
Procedimiento de instalacin
86
x 2).
x 1).
8. Retire lo siguiente:
Bandeja interior [A] (
x 2)
x 2)
x 1)
x 1)
x 1)
87
2. Instalacin
x 6).
Si se va a instalar la unidad de perforacin (D390) con este finisher (D429) al mismo tiempo, omita
el siguiente procedimiento, y consulte el procedimiento de instalacin de la "Unidad de perforacin
(D390)".
88
2. Inserte dos pasadores de unin [A] en los dos orificios del soporte trasero interno.
3. Conecte por completo el lado delantero [B] de la unidad del inversor a la unidad de salida de papel
de la unidad principal despus de insertar los dos pasadores de unin ( x 1: M3x6).
Inserte los dos pasadores de unin antes de conectar el lado delantero de la unidad del inversor
a la unidad de salida de papel de la unidad principal. En caso contrario, pueden producirse
atascos de papel entre la unidad de salida de papel y la unidad del inversor.
89
2. Instalacin
x 2: M3x6).
x 3: M3x10).
90
x 1: M3x6).
91
2. Instalacin
92
Descripcin
Cantidad
Unidad de perforacin
Abrazadera
Tapa de perforacin
Procedimiento de instalacin
Si el finisher interno no se ha instalado an, omita la seccin "Retirada del finisher interno" y pase a la
seccin "Preparacin de la unidad de perforacin antes de la instalacin del finisher interno". Realice
tambin la "Preparacin antes de la instalacin del finisher interno" en la seccin "Finisher interno (D429)".
Si ya se ha instalado el finisher interno, debe retirarlo en primer lugar. Empiece con la seccin "Retirada
del finisher interno".
x 1).
3. Desconecte el cable [A] del enchufe de la mquina y saque el finisher interno [B].
93
2. Instalacin
2
4. Retire el finisher interno [A] (
94
x 1: M3x6).
x 3: M3x10).
x 2: M3x6).
x 1: M3x6).
95
2. Instalacin
x 4).
3. Retire el soporte de los pasadores de posicionamiento [A] del soporte derecho del inversor (
96
x 1: M3x6).
x 2).
5. Deslice la gua pequea del inversor [A] hacia el lado delantero (direccin de la flecha) y retrela
( x 1).
6. Retire todas las cintas adhesivas de la unidad de perforacin.
Si no se retiran todas las cintas adhesivas, se puede producir un SC763.
7. Fije la unidad del inversor [A] a la unidad de perforacin [B], y luego asegure la unidad del inversor
con la unidad de perforacin ( x 4 retirados en el paso 1).
8. Fije el conector del cajn [A] de la unidad de perforacin al soporte trasero de la unidad del inversor
( x 2 retirados en el paso 3).
9. Fije la abrazadera [B] al soporte trasero de la unidad del inversor.
97
2. Instalacin
2. Inserte los dos pasadores de unin [A] (esta imagen no muestra los dos pasadores de unin) en los
dos orificios del soporte trasero interno.
3. Conecte por completo el lado delantero [B] de la unidad del inversor a la unidad de salida de papel
de la unidad principal despus de insertar los dos pasadores de unin ( x 1: M3x6).
Inserte los dos pasadores de unin antes de conectar el lado delantero de la unidad del inversor
a la unidad de salida de papel de la unidad principal. En caso contrario, pueden producirse
atascos de papel entre la unidad de salida de papel y la unidad del inversor.
98
2
4. Retire el tope [A] del ral gua y luego conecte con los orificios de los tornillos [B] (estos orificios de
tornillos deben utilizarse cuando el finisher interno est instalado con la unidad de perforacin).
x 2).
x 3: M3x6).
99
2. Instalacin
1. Retire la tapa trasera izquierda [A] y la tapa trasera [B] del finisher interno (
100
x 2).
x 2 cada uno).
x 1).
x 2).
x 2); este soporte es para el finisher interno cuando se utiliza con la unidad
101
2. Instalacin
4. Retire la tapa inferior de la bandeja de salida [A]; esta tapa es para el finisher interno sin la unidad
de perforacin ( x 3).
5. Fije la tapa inferior de la bandeja de salida [A]; esta tapa es para el finisher interno cuando se utiliza
con la unidad de perforacin ( x 3).
102
Nota
Las dos proyecciones [A] en la tapa inferior de la bandeja de salida (esta placa ya est conectada
a la tapa inferior de la bandeja de salida) deben insertarse a lo largo de los rales gua [B] dentro
de la unidad de bandeja de salida.
Pulse la placa deslizante [A] para comprobar si la tapa inferior de la bandeja de salida est
instalada correctamente. La imagen lateral izquierda muestra el resultado correcto y la imagen
lateral derecha muestra el resultado incorrecto.
103
2. Instalacin
x 2).
104
Descripcin
Cantidad
Alimentador de sobres
Procedimiento de instalacin
Esta bandeja slo se puede instalar en la bandeja 1 de la copiadora. No instale esta bandeja en
otra bandeja que no sea la bandeja 1. De lo contrario se podra producir un atasco o algn otro
problema con el papel.
1. Retire todas las cintas adhesivas y la etiqueta roja del alimentador de sobres.
105
2. Instalacin
106
Descripcin
Cantidad
Bandeja superior
Bandeja inferior
Soporte de bandeja
Tornillo: M3 x 8
Tornillo: M3 x 14*1
Tornillo: M3 x 25
Tornillo de rosca: M3 x 10
Abrazadera
107
2. Instalacin
Procedimiento de instalacin
[C] x 2: M3x10,
[D]
Para este modelo, utilice los orificios de tornillos marcados como "3" en el soporte de la mesa.
x 2: M3x8).
x 1: M3x8).
5. Utilice las abrazaderas si es necesario para pinzar el cable del dispositivo de lectura/escritura de
tarjetas.
108
El lector de tarjetas inteligentes debe colocarse en esta tabla del lector de tarjetas. De lo contrario,
se podra interrumpir la antena o el transmisor de la mquina principal.
109
2. Instalacin
Descripcin
Cantidad
Placa de masa
Cable USB
Tornillo: M3 x 6 azul
Tornillo: M3 x 8
Etiqueta
Abrazadera
Procedimiento de instalacin
1. Conecte el cable USB [B] a la ranura USB [A] en la unidad de la ranura USB2.0/SD.
2. Conecte la placa de masa [C] al soporte de la ranura USB2.0/SD (
110
x 1: M3x6 azul).
x 8).
x2).
x 2).
111
2. Instalacin
2
7. Realice cuatro orificios en la tapa izquierda del escner con un destornillador como se ha indicado
anteriormente [A].
Alise los cuatro orificios de la cubierta izquierda del escner como se indic anteriormente [B].
8. Inserte el cable USB [A] a travs de los huecos de la cubierta izquierda del escner.
9. Fije la ranura USB2.0/SD [B] con la cubierta izquierda del escner como se indic anteriormente
( x 4: M3x8).
Utilice los orificios de los tornillos [C] como se indic anteriormente.
112
x 2).
11. Conecte el cable USB [B] a USB-A (la ranura USB ms cercana al lado delantero de la mquina)
como se mostr anteriormente.
Asegrese de que el cable USB est insertado en USB-A (parte frontal).
113
2. Instalacin
x 1).
Pg.137).
25. Pegue la etiqueta adhesiva [A] a la ranura USB2.0/SD como se ha indicado anteriormente.
114
115
2. Instalacin
Procedimiento de instalacin
1. Tapa posterior (
Pg.175)
Pg.175)
Pg.302)
5. Fije el contador mecnico [A] al soporte [B] y conecte el mazo de cables a cada contador mecnico
como se mostr anteriormente.
Uno [C] de los dos mazos de cables no se utiliza en este modelo.
116
x 2).
7. Conecte el mazo de cables del contador mecnico [C] al contador mecnico [D] y a la BCU (CN218)
[E], y dirija el mazo de cables como se mostr anteriormente ( x 5)
8. Monte de nuevo la mquina.
9. Enchufe la mquina y encienda el interruptor de alimentacin.
10. Active el modo SP.
11. Ajuste SP5987-001 en "1: ON" (1: Encendido).
12. Salga del modo SP, y apague y vuelva a encender la mquina.
117
2. Instalacin
Auricular (B433)
Procedimiento de instalacin
1. Sujete las tuercas de la placa del contador llave [A] en el interior del soporte del contador de llave
[B] e introduzca el casquillo del contador llave [C].
2. Fije el casquillo del contador llave al soporte (
3. Instale la tapa del contador llave [D] (
4. Cubierta posterior (
118
Pg.175)
x 2).
x 2).
6. Retire la cinta adhesiva de dos caras del soporte del contador llave y fije el contador llave a la tapa
izquierda del escner.
119
2. Instalacin
1. Tapa posterior (
Pg.175)
Pg.175)
Pg.302)
120
x 4).
7. Conecte y encamine el cable del contador llave [A] al conector del circuito de interfaz del contador
llave como se mostr anteriormente (tornillo de toma de tierra x 1,
x 6).
8. Conecte y encamine el mazo de cables [B] al conector en el circuito de interfaz del contador llave
y al conector CN216 [C] en la BCU ( x 5)
9. Tire del cable del contador llave a travs del hueco y conctelo al conector [A] de la unidad del
contador llave.
10. Monte de nuevo la mquina.
121
2. Instalacin
Calentador anticondensacin
Procedimiento de instalacin
Pg.175)
122
x 2)
Calentador anticondensacin
123
2. Instalacin
9. Mueva transversalmente el carro del escner por completo hasta el lado derecho girando el motor
del escner [A] en la parte trasera de la mquina.
10. Pase el conector del calentador [B] a travs del hueco [C].
124
Calentador anticondensacin
11. Mueva el carro del escner hasta el lado izquierdo como se mostr anteriormente, girando el motor
del escner en la parte trasera de la mquina.
12. Instale el calentador en la unidad de escner (
x 1).
13. Asegure la tapa del cable [A] y el lado izquierdo del calentador (
x 1).
125
2. Instalacin
Calentador de bandejas
Procedimiento de instalacin
Equipo principal
x 1).
126
x 1).
Calentador de bandejas
1. Retire la tapa del conector trasero [A] (tornillo de remache x 1) de la unidad principal.
2. Desconecte el mazo de cables [B].
x 5).
127
2. Instalacin
x 1)
8. Conecte el mazo de cables [A] del calentador al mazo de cables del rel [B].
128
Calentador de bandejas
9. Inserte el mazo de cables del calentador [A] en el tubo [B] y presione el tubo contra el marco trasero
de la unidad de alimentacin de papel como se mostr anteriormente.
Asegrese de que el tubo est en contacto con el marco trasero [C].
x 5).
Asegrese de que el conector [A] est colocado de forma segura como se muestra
anteriormente.
Asegrese de que el borde del tubo [B] est colocado como se muestra anteriormente.
11. Vuelva a colocar la tapa trasera de la unidad de alimentacin de papel (
fijacin ( x 1 cada uno)
x 2) y los soportes de
129
2. Instalacin
12. Retire la tapa del conector [A] del mazo de cables del calentador de bandejas.
13. Conecte el mazo de cables del rel [B] al mazo de cables del calentador de bandejas [C] de la
unidad principal.
No conecte el mazo de cables del rel [B] al mazo de cables del calentador de bandejas de
la unidad principal antes de instalar el soporte de fijacin [D]. De lo contrario, el soporte de
fijacin podra pinzar el mazo de cables del rel.
14. Sujete el mazo de cables [A] con una abrazadera como se muestra anteriormente (
15. Vuelva a instalar la tapa inferior trasera de la unidad principal (
16. Vuelva a instalar todos los casetes de bandeja.
130
x 5).
x 1).
Calentador de bandejas
1. Retire la tapa del conector trasero [A] (tornillo de remache x 1) de la unidad principal.
2. Desconecte el mazo de cables [B].
x 5).
131
2. Instalacin
x 1).
8. Conecte el mazo de cables del calentador [A] al mazo de cables del rel [B].
132
Calentador de bandejas
2
9. Retire la gua del mazo de cables [A] (
indica anteriormente.
10. Inserte el mazo de cables del calentador [A] en el tubo [B] y presione el tubo contra el marco trasero
de la unidad de alimentacin de papel como se mostr anteriormente.
Asegrese de que el tubo est en contacto con el marco trasero [C].
133
2. Instalacin
x 6).
Asegrese de que el borde del tubo [A] est colocado como se muestra anteriormente.
No se utiliza la abrazadera [B].
x 2) y los soportes de
14. Retire la tapa del conector [A] del mazo de cables del calentador de bandejas.
15. Conecte el mazo de cables del rel [B] al mazo de cables del calentador de bandejas [C] de la
unidad principal.
No conecte el mazo de cables del rel [B] al mazo de cables del calentador de bandejas de
la unidad principal antes de instalar el soporte de fijacin [D]. De lo contrario, el soporte de
fijacin podra pinzar el mazo de cables del rel.
134
Calentador de bandejas
16. Sujete el mazo de cables [A] con una abrazadera como se muestra anteriormente (
17. Vuelva a instalar la tapa inferior trasera de la unidad principal (
x 1).
x 5).
135
2. Instalacin
Esta mquina cuenta con ranuras para tarjetas de interfaz destinadas a conexiones de interfaz y
aplicaciones de tarjeta SD opcionales.
Despus de instalar una opcin, compruebe que el aparato la reconoce (consulte Comprobacin de
todas las conexiones al final de esta seccin).
136
Ranuras USB
Ranura USB del lado izquierdo [C]: se utiliza para conectar una cmara digital (slo funciona si est
instalado PictBridge).
Ranura USB del lado derecho [D]: se utiliza al instalar la ranura de tarjeta USB2.0/SD opcional
La aplicacin PostScript3 y sus fuentes no pueden trasladarse a otra tarjeta SD. Sin embargo, otras
aplicaciones s se pueden trasladar a la tarjeta SD PostScript3.
Aspectos generales
El programa de servicio "Mover aplicacin tarjeta SD" (SP5-873) le permite copiar programas de
aplicacin desde una tarjeta SD a otra.
La ranura 1 es slo para almacenar programas de aplicacin. Pero existen cuatro aplicaciones posibles
(PostScript 3, Security Card (DataOverwriteSecurity y Unidad de cifrado del disco duro), PictBridge, IPDS).
No puede ejecutar programas de aplicacin desde la ranura 2. Sin embargo, puede trasladar programas
de aplicaciones desde la ranura 2 a la ranura 1 con el siguiente procedimiento.
Asegrese de que la tarjeta SD de destino cuenta con espacio suficiente.
1. Entre en el SP5873 "Mover aplicacin tarjeta SD".
2. Despus mueva la aplicacin desde la tarjeta SD de la ranura 2 a la tarjeta SD de la ranura 1.
Repita los pasos 1-2 si desea transferir otro programa de aplicacin.
3. Salga del modo SP.
Tenga cuidado al utilizar el procedimiento Mover aplicacin ("Move Appli") de la tarjeta SD:
Los datos necesarios para la autenticacin se transfieren con el programa de aplicacin de una
tarjeta SD a otra. La autenticacin fallar si intenta utilizar la tarjeta SD despus de copiar el programa
de aplicacin de una tarjeta a otra.
No utilice la tarjeta SD si se ha utilizado anteriormente para otros fines. Si se hace, no se garantiza
un funcionamiento correcto.
No retire la tarjeta SD de su sitio despus de copiar el programa de aplicacin de una tarjeta a otra.
Debe hacerlo por los motivos siguientes:
137
2. Instalacin
1) La tarjeta SD puede ser la nica prueba de que el usuario dispone de licencia para usar el
programa de aplicacin.
2) Puede necesitar comprobar la tarjeta SD y los datos que contiene para resolver un problema en
el futuro.
Mover ejecutables
El men "Move Exec" (SP5-873-001) permite copiar programas de aplicacin de la tarjeta SD original
a otra tarjeta SD.
No active el switch de proteccin contra escritura de la tarjeta SD del sistema o de la tarjeta SD de
la aplicacin en la mquina. Si el switch de proteccin contra escritura est en ON, se producir un
error de descarga (por ejemplo, Cdigo de error 44) durante la actualizacin del firmware o la
fusin de aplicaciones.
1. Apague el interruptor principal.
2. Asegrese de que hay una tarjeta SD en la ranura 1. El programa de aplicacin se copia en esta
tarjeta SD.
3. Introduzca la tarjeta SD (que contiene el programa de aplicacin) en la ranura para tarjetas SD 2.
El programa de aplicacin se copiar desde esta tarjeta SD.
4. Encienda el interruptor principal.
138
Deshacer ejecutables
"Deshacer ejecutables" (SP5-873-002) le permite volver a copiar los programas de aplicacin desde
una tarjeta SD a la tarjeta SD original. Puede usar este programa, por ejemplo, cuando haya copiado
programas por error usando Mover ejecutables (SP5-873-001).
No active el switch de proteccin contra escritura de la tarjeta SD del sistema o de la tarjeta SD de
la aplicacin en la mquina. Si el switch de proteccin contra escritura est en ON, se producir un
error de descarga (por ejemplo, Cdigo de error 44) durante la actualizacin del firmware o la
fusin de aplicaciones.
1. Apague el interruptor principal.
2. Introduzca la tarjeta SD original en la ranura 2 para tarjetas SD. El programa de aplicacin volver
a copiarse en esta tarjeta.
3. Introduzca la tarjeta SD (que contiene el programa de aplicacin) en la ranura 1 para tarjetas SD.
El programa de aplicacin se copiar desde esta tarjeta SD.
4. Encienda el interruptor principal.
5. Inicie el modo SP.
6. Seleccione SP5-873-002 "Undo Exec." (Deshacer ejec.)
7. Siga las instrucciones de los mensajes que aparecen en el panel de mandos.
8. Apague el interruptor principal.
9. Retire la tarjeta SD de la Ranura 2.
En este paso se supone que el aparato utiliza los programas de aplicacin contenidos en la
tarjeta SD.
10. Encienda el interruptor principal.
11. Compruebe que los programas de aplicacin se ejecutan normalmente.
12. Compruebe que la mquina reconoce la opcin (consulte "Comprobar todas las conexiones" al final
de esta seccin).
139
2. Instalacin
PostScript 3
La aplicacin PostScript3 y sus fuentes no pueden trasladarse a otra tarjeta SD. Sin embargo, otras
aplicaciones s se pueden trasladar a la tarjeta SD PostScript3.
x 1).
3. Gire la cara de la etiqueta para tarjetas SD de la tarjeta de seguridad [A] hacia la parte delantera
de la mquina. Despus, empjela [A] lentamente en la ranura SD 2 [B] hasta que oiga un clic.
4. Gire la cara de la etiqueta para tarjetas SD del PostScript3 [B] hacia la parte delantera de la mquina.
Despus, empjela lentamente en la ranura 1 [B] hasta que oiga un clic.
5. Enchufe y encienda el interruptor de alimentacin principal, luego ejecute "Move Exec" (Mover ejec.)
con SP5-873-001.
140
Para obtener detalles, consulte "SD Card Appli Move" (Mover aplicacin tarjeta SD).
6. Apague la mquina despus de completar "Move Exec" (Mover ejec.).
7. Retire la tarjeta de seguridad de la ranura SD 2 y gurdela en su sitio para el almacenamiento de
tarjetas SD ( Pg.137 "Mover aplicaciones de tarjeta SD").
8. Reinstale la tarjeta VM en la ranura SD 2
9. Coloque la tapa de la ranura SD (
x 1).
10. Pegue la etiqueta adhesiva "Adobe PostScript 3" [A] en la puerta delantera.
11. Compruebe que la mquina reconoce la opcin (consulte "Comprobar todas las conexiones" al final
de esta seccin).
141
2. Instalacin
x 2).
2. Instale el convertidor de formatos de archivo [B] en la ranura I/F y fjelo con los tornillos.
3. Enchufe la mquina y encienda el interruptor de alimentacin.
4. Compruebe o defina los siguientes cdigos SP con los valores que se indican a continuacin.
N. de SP
Ttulo
Ajuste
SP5-836-001
"1"
SP5-836-002
"0"
5. Compruebe el funcionamiento.
6. Compruebe que la mquina reconoce la opcin (consulte "Comprobar todas las conexiones" al final
de esta seccin).
IEEE1284
142
x 2).
143
2. Instalacin
x 2).
4. Despegue los adhesivos de doble cara de las fijaciones de Velcro [A] y pguelas en las reas frontal
izquierda y posterior izquierda de la mquina.
5. Fije "ANT1" (con ncleo de ferrita negro) [B] en la parte delantera izquierda de la mquina.
6. Fije "ANT2" (con ncleo de ferrita blanco) [C] en la parte trasera derecha de la mquina.
144
x 7).
Compruebe que los cables no quedan flojos. Deben quedar pegados a las tapas.
145
2. Instalacin
4. Pulse "Wireless LAN" (LAN inalmbrica). Slo aparecen las opciones de LAN inalmbrica.
5. Modo de comunicacin. Seleccione "802.11 Ad hoc", "Ad hoc" o "Infrastructure" (Infraestructura).
6. SSID Setting (Ajuste de SSID). Introduzca el ajuste de SSID (el ajuste distingue entre maysculas y
minsculas).
7. Channel (Canal). Este ajuste es necesario si se selecciona el modo Ad Hoc.
146
SSID
Clave WEP
Nombre
Funcin
5840-006
Canales MAX
5840-007
Canales MIN
5840-011
Seleccin de clave
WEP
Modo UP
Nombre
Funcin
SSID
Clave WEP
Modo WEP
Bluetooth
147
2. Instalacin
x 2).
PictBridge
148
Debe instalar la opcin PictBridge en la ranura de tarjeta SD 1. Sin embargo, la opcin Postscript3,
tarjeta de seguridad y unidad IPDS tambin estn instaladas en la ranura de la tarjeta SD 1. Debe
realizar el procedimiento SD Card Appli move (Mover aplicacin tarjeta SD) primero si tiene la
opcin PpostScript3, tarjeta de seguridad o unidad IPDS instalada y quiere instalar la unidad
PictBridge.
x 1).
3. Gire la cara de la etiqueta de la tarjeta SD [A] de la PictBridge hacia la parte delantera de la mquina.
Despus, empjela lentamente en la ranura 2 para tarjetas SD hasta que oiga un clic.
4. Enchufe y encienda el interruptor de alimentacin principal, luego ejecute "Move Exec" (Mover ejec.)
con SP5-873-001.
Para obtener detalles, consulte "SD Card Appli Move" (Mover aplicacin tarjeta SD).
5. Apague la mquina despus de completar "Move Exec" (Mover ejec.).
149
2. Instalacin
x 1).
9. Compruebe que la mquina reconoce la opcin (consulte "Comprobar todas las conexiones" al final
de esta seccin).
150
x 1).
3. Gire la cara de la etiqueta de la tarjeta SD de la unidad de navegador [A] hacia la parte delantera
de la mquina. Despus, introdzcala lentamente en la ranura SD 2 [A] hasta que oiga un clic.
4. Enchufe la mquina y encienda el interruptor de alimentacin.
5. Pulse la tecla "User Tools" (Herramientas de usuario).
Si la mquina tiene registrado un ajuste de administrador, los pasos 5 y 6 son obligatorios. En
caso contrario, contine en el paso 7.
6. Pulse la tecla "Login/ Logout" (Inicio/Fin de sesin).
7. Inicie sesin con el nombre de usuario y contrasea del administrador.
8. Pulse "Ajustes de funciones ampliadas" dos veces en la pantalla LCD.
9. Pulse "Install" (Instalar) en la LCD.
10. Pulse SD Card (Tarjeta SD).
11. Pulse en la lnea Browser (Navegador).
12. En "Instalar en" ("Install to"), pulse "HDD de la mquina" ("Machine HDD") y despus en
"Siguiente" ("Next").
13. Cuando vea "Listo para instalar", compruebe la informacin de la pantalla para confirmar su
seleccin anterior.
14. Pulse "OK". Aparecer el mensaje "Installing the extended feature... Please wait." (Instalando la
funcin ampliada... Espere) y, a continuacin, el mensaje "Completed" (Terminado).
15. Pulse "Exit" (Salir) para volver a la pantalla de ajustes.
16. Pulse "Change Allocation" (Cambiar asignacin).
17. Pulse en la lnea Browser (Navegador).
18. Pulse la tecla que desee utilizar para la unidad del navegador. De forma predeterminada, esta
funcin est asignada a la tecla "Otras funciones" (ltima tecla de las teclas de funcin).
19. Pulse "OK".
20. Pulse "Salir" ("Exit") dos veces para volver a la pantalla de copia.
151
2. Instalacin
x 1).
26. Conserve esta tarjeta SD en su lugar ( Pg.137 "Mover aplicaciones de tarjeta SD") despus de
haber instalado el programa de aplicacin en el HDD desde la tarjeta. Esto se debe a que la tarjeta
SD puede ser la nica prueba de que el usuario posee una licencia para utilizar el programa de
aplicacin. Puede que en el futuro necesite consultar la tarjeta SD y los datos que contiene para
resolver algn problema.
Gigabit Ethernet
152
x 8)
x 1).
x 2).
4. Inserte el circuito Gigabit Ethernet [A] en el conector [B] del circuito del controlador.
x 2).
x 2) y la tapa trasera (
x 8).
153
2. Instalacin
2
7. Fije el ncleo de ferrita [A] al cable LAN [B] como se muestra anteriormente, y conecte el cable LAN
a la mquina.
8. Compruebe que la mquina reconoce esta opcin (consulte Comprobacin de todas las
conexiones al final de esta seccin).
154
3. Mantenimiento preventivo
Tablas de mantenimiento
Consulte "Apndices" para obtener la informacin siguiente:
Elementos de mantenimiento preventivo
Otras piezas de consumibles
155
3. Mantenimiento preventivo
SP
Negro: 3902-001
Unidad de revelado
Cian: 3902-002
Magenta: 3902-003
Amarillo: 3902-004
Negro: 3902-009
Cian: 3902-010
Magenta: 3902-011
Amarillo: 3902-012
Unidad de ITB
3902-013
Unidad de fusin
3902-014
3902-016
3902-017
Unidad PTR
3902-018
3902-019*1
3902-020*1
*1: Slo si la botella de recogida de tner se sustituye antes de que la mquina detecte que est casi
llena.
156
Para las siguientes unidades, hay un nuevo mecanismo de deteccin de unidad. No es necesario para
reiniciar los contadores PM.
Unidad de revelado
Botella de recogida de tner de PCU/ITB (si est llena o casi llena)
3. Asegrese de que los contadores de mantenimiento preventivo para las unidades sustituidas estn
a "0" con SP7-803. Si no se ha reiniciado el contador de mantenimiento preventivo para una unidad,
entonces reincielo con SP 7-804.
4. Asegrese de que el contador de intercabio aumenta con SP7-853.
5. Asegrese de que los contadores para las unidades anteriores (SP7-906) en la lista de datos de
registro SMC (del paso 2 anterior) son iguales a los contadores (SP7-803) para estas unidades en
la lista de registro SMC anterior (la lista que se gener en la seccin "Antes de retirar las piezas
antiguas").
6. Asegrese de que la fecha de sustitucin de la unidad se ha actualizado con SP7-950.
3. Mantenimiento preventivo
Comprobacin de la operacin
158
4. Sustitucin y ajuste
Previamente
Opciones de instalacin, haga lo siguiente:
Si hay una unidad de fax en la mquina, imprima todos los mensajes almacenados en la memoria,
las listas de los elementos programados por el usuario y la lista de los parmetros del sistema.
Si hay trabajos de impresin en el aparato, imprima todos los trabajos de la memoria intermedia de
la impresora.
Apague el interruptor principal y desconecte el cable de alimentacin, la lnea de telfono y el cable
de red.
Toque siempre una superficie con conexin a tierra para descargar la electricidad esttica de las
manos antes de manipular tarjetas SD, placas de circuito impreso o placas de memoria.
159
4. Sustitucin y ajuste
Herramientas especiales
Nmero de pieza
160
Descripcin
Cantidad
B6455010
Tarjeta SD
G021 9350
C4019503
Ampliacin de 20X
A257 9300
A092 9503
B6795100
A184 9501
5203 9502
Ajuste de la imagen
Ajuste de la imagen
Escaneo
Compruebe el ajuste de registro/lado a lado de impresin y el ajuste de margen en blanco antes de
realizar los siguientes ajustes del escner.
Utilice el grfico de prueba S-2-1 para realizar los ajustes siguientes.
A: Ampliacin de subescaneo
1. Coloque el grfico de pruebas sobre el cristal de exposicin. A continuacin, haga una copia desde
una de las estaciones de alimentacin.
2. Verifique el porcentaje de ampliacin. Ajstelo con SP4-008 si es necesario.
Estndar: 1,0%
161
4. Sustitucin y ajuste
4
A: registro de cabecera
1. Coloque el grfico de pruebas sobre el cristal de exposicin. A continuacin, haga una copia desde
una de las estaciones de alimentacin.
2. Compruebe el borde inicial y el registro de lado a lado. Ajuste con los siguientes modos de SP si
fuera necesario.
Estndar: 0 2 mm para el registro del borde delantero, 0 2 mm para el registro de lado a lado.
Modo SP
162
SP4-010-001
SP4-011-001
Ajuste de la imagen
ARDF
ARDF de lado a lado, registro de borde delantero y borde posterior
4
A: Registro de borde delantero, B: Registro de lado a lado
Utilice papel A3/DLT para realizar el grfico de prueba temporal como se muestra anteriormente.
1. Coloque el grfico de pruebas temporal sobre el ARDF. A continuacin, haga una copia desde una
de las estaciones de alimentacin.
2. Compruebe el registro. Compruebe el borde inicial y el registro de lado a lado. Ajuste con los
siguientes modos de SP si fuera necesario.
Estndar: 4,2 3,0 mm para el registro del borde delantero, 2 3,0 mm para el registro de lado a
lado. Utilice los modos de SP siguientes para realizar los ajustes si es necesario.
Cdigo SP
Qu hace
Intervalo de ajuste
SP6-006-001
3,0 mm
SP6-006-002
3,0 mm
SP6-006-003
5,0 mm
SP6-006-005
5,0 mm
SP6-006-006
5,0 mm
SP6-006-007
5,0 mm
163
4. Sustitucin y ajuste
Registration (Registro)
rea de imagen
Borde anterior
Ajusta el registro de borde delantero para cada tipo de papel y para cada velocidad de lnea de proceso.
Lado a lado
Ajusta el registro de lado a lado para cada estacin de alimentacin de papel. Utilice el modo de SP
(SP1-002) para ajustar el registro de lado a lado para la unidad de papel opcional, la LCT y la unidad
dplex.
164
Ajuste de la imagen
Estndar de ajuste
Borde delantero (direccin de escaneo secundario): 4,2 1,5 mm
De lado a lado (direccin de escaneo principal): 2,25 1,75 mm
Procedimiento de ajuste
1. Entre en SP2-109-003.
2. Imprima la trama de prueba (14: rea de recorte) con SP2-109-003.
El registro puede variar ligeramente, como se indica en la pgina anterior. Imprima algunas
pginas del "rea de recorte" para los pasos 3 y 4. Luego calcule el promedio de los valores
de registro de borde delantero y de lado a lado y ajuste cada uno de los modos SP.
3. Haga el ajuste de registro de borde delantero.
1) Compruebe el registro de borde delantero y ajstelo con SP1-001.
2) Seleccione las condiciones de ajuste (tipo de papel y velocidad de lnea de proceso).
3) Introduzca el valor. A continuacin, pulse la tecla
4. Sustitucin y ajuste
4
1. Entre en SP2-109-003.
2. Imprima la trama de prueba (14: trama de recorte de 1 punto) con SP2-109-003.
3. Compruebe el margen de borrado A y B. Ajstelos con SP2-103-001 a -010 si es necesario.
Borde delantero: 1,5 hasta 5,0 mm,
De lado a lado: 0,5 a 4,0 mm,
Borde posterior: 0,5 a 0,6 mm
Registro de color
Ajuste de posicin de lnea
El ajuste automtico de posicin de lnea suele hacerse para una condicin especificada, a fin de obtener
los mejores resultados en las impresiones en color.
Si el registro de color se desplaza, haga lo siguiente:
Ejecute "Auto Color Registration" (Registro automtico de color) de la manera siguiente para realizar
el ajuste forzado de la posicin de lnea.
1. Ejecute primero el SP2-111-3.
2. A continuacin, ejecute el SP2-111-1.
Para comprobar si el SP 2-111-1 se ha ejecutado correctamente, observe la pantalla durante el
proceso. Al final aparece un mensaje. Adems, puede comprobar el resultado con SP 2-194-007
(0: completado con xito, 1: fallido).
166
Ajuste de la imagen
El ACC generalmente es suficiente para ajustar el balance de color para obtener la mxima calidad
de impresin. Basta con realizar la correccin de gamma de la impresora para afinar los ajustes
para cubrir las necesidades del usuario.
Utilice los modos de SP si desea modificar la curva de gamma creada con el ACC. Puede ajustar los datos
de gamma para lo siguiente:
Resalte
Media
reas de sombra
IDmx.
El intervalo ajustable abarca de 0 a 30 (31 pasos).
Modo Copia
- Modo de foto Elemento para ajustar
IDmx.
1
(K, C, M e Y)
Estndar de ajuste
Ajuste el valor de desplazamiento
de forma que la densidad del nivel
10 coincida con la del nivel 10 del
grfico C-4.
167
4. Sustitucin y ajuste
Estndar de ajuste
(K, C, M e Y)
(K, C, M e Y)
(K, C, M e Y)
DI mx.: (K, C, M e Y)
Estndar de ajuste
Ajuste el valor de desplazamiento
de forma que la densidad del nivel
10 coincida con la del nivel 10 del
grfico C-4.
168
Ajuste de la imagen
Estndar de ajuste
(K, C, M e Y)
(K, C, M e Y)
(K, C, M e Y)
DI mx.: (K)
Estndar de ajuste
Ajuste el valor de
desplazamiento de forma que la
densidad del nivel 10 coincida
con la del nivel 10 del grfico
C-4.
Ajuste el valor de
desplazamiento para que la
densidad del nivel 6 coincida
con la del nivel 6 del grfico C-4.
169
4. Sustitucin y ajuste
Estndar de ajuste
Ajuste el valor de
desplazamiento para que la
densidad del nivel 8 coincida
con la del nivel 8 del grfico C-4.
Ajuste el valor de
desplazamiento para que un
fondo sucio no sea visible en la
copia y la densidad del nivel 3
sea ligeramente inferior a la del
nivel 3 en el grfico C-4.
Las partes de texto de este patrn de prueba no pueden imprimirse con claridad despus de ajustar
la "sombra" como se indica anteriormente. En este momento, compruebe si el patrn de 5 lneas/
mm de cada esquina se imprime con claridad. Si no es as, vuelva a ajustar el valor de desplazamiento
de "sombra" hasta que se imprima con claridad.
Modo Impresora
Hay seis modos ajustables (seleccione estos modos con SP1-102-001 de la impresora):
Modo de foto de 1200 x 1200
Modo de texto de 1200 x 1200
Modo de foto de 2400 x 600
Modo de texto de 2400 x 600
Modo de foto de 1800 x 600
Modo de texto 1800 x 600
Modo de foto 600 x 600
Modo de texto 600 x 600
K
170
Ajuste de la imagen
Resalte
SP1-104-1
SP1-104-21
SP1-104-41
SP1-104-61
Sombreado
SP1-104-2
SP1-104-22
SP1-104-42
SP1-104-62
Media
SP1-104-3
SP1-104-23
SP1-104-43
SP1-104-63
DI mx.
SP1-104-4
SP1-104-24
SP1-104-44
SP1-104-64
6. Elija SP1-103-1 para imprimir una hoja de prueba de control de tonos si desea examinar la calidad
de imagen para estos ajustes.
7. Ajuste la densidad del color con SP1-104. Compare la hoja de prueba de control de tonos con el
grfico de prueba C4.
Ajuste la densidad en este orden: "ID Max", "Shadow", "Middle", "Highlight" (DI mx,
sombreado, media, resalte).
8. Utilice SP1-105-001 para conservar los parmetros ajustados.
171
4. Sustitucin y ajuste
Tapas exteriores
Botella de recogida de tner PCDU
Si cambia esta botella de recogida de tner despus de que la mquina detecte que est llena o casi
llena, la mquina restablecer automticamente el contador de PM de la botella de recogida de tner
de la PCDU.
Pero, si cambia una botella que no est llena o casi llena, deber restablecer el contador PM de esta
unidad. Para ello, ajuste SP 3902 019 en 1 antes de empezar a trabajar en la mquina.
Puerta delantera
1. Abra la puerta delantera.
172
Tapas exteriores
Pg.172)
x 2, pin x 2)
x 2).
173
4. Sustitucin y ajuste
2. Libere la pestaa [A], y luego retire la tapa de la unidad de limpieza de la ITB [B].
Tapa izquierda
174
x 10)
Tapas exteriores
Tapa trasera
4
1. Tapa trasera [A] (
x 8)
x 5)
175
4. Sustitucin y ajuste
Filtro de polvo
4
1. Tapa del filtro de polvo [A] (ganchos)
2. Filtro de polvo [B]
Pg.175)
176
x 5)
Tapas exteriores
Panel de mandos
4
1. Retire los seis tornillos del panel de mandos [A].
2. Deslice el panel de mandos hasta el lado delantero.
177
4. Sustitucin y ajuste
No utilice los elementos [2] a [9] del men de autodiagnstico. Slo se utilizan en el momento del diseo.
1. Pulse
, pulse "1", "1", "9", "3" y despus pulse
(Self-Diagnostics).
2. En la pantalla tctil, pulse Touch Screen Adjust" (Ajuste de pantalla tctil) (o bien pulse "1").
3. Utilice un objeto con punta (no afilada) para presionar la marca superior izquierda
6. Pulse [#] Exit (Salir) en la pantalla para cerrar el men de autodiagnstico. Guarde los ajustes de
calibracin.
178
Pg.172)
Tapas exteriores
2. Presione la palanca de bloqueo de ITB [A] y sbala en direccin de las agujas del reloj como se
muestra anteriormente.
3. Tapa derecha interna [B] (
x 2)
Tapa interior
1. Botella de recogida de tner de la PCDU (
2. Tapa derecha interior (
Pg.172)
Pg.178)
x 4)
Pg.172)
Pg.178)
179
4. Sustitucin y ajuste
4. Retire la tapa derecha delantera [A] con el panel de mandos [B] levantado (
180
x 2).
x 1).
Tapas exteriores
4
1. Tapa del marco izquierdo [A] (
x 1)
x 2)
x 1)
181
4. Sustitucin y ajuste
4
1. Bandeja del inversor [A] (ganchos)
Bandeja interna
x 2)
182
Pg.182)
Tapas exteriores
x 1)
183
4. Sustitucin y ajuste
Pg.175)
x 4)
184
x 2)
Coloque el marcador blanco [B] en la esquina trasera izquierda cuando vuelva a instalar el
cristal de exposicin del ARDF.
x 3)
185
4. Sustitucin y ajuste
Pg.184)
x 6)
Los tres tornillos [B] no se tienen que retirar por completo. Afljelos simplemente para retirar la
tapa de la SBU
186
x1,
x 1 cada uno))
Lmpara de exposicin
1. Tapa posterior (
2. Panel de mandos (
Pg.175)
Pg.177)
3. Cristal de exposicin (
Pg.184)
x 1)
187
4. Sustitucin y ajuste
188
x 1)
9. Polea [C]
10. Libere la abrazadera del cable [A] (un gancho bajo la abrazadera del cable) en el extremo trasero
de la lmpara de exposicin.
11. Presione el retn [B] y deslice la lmpara de exposicin [C] hacia el lado delantero.
189
4. Sustitucin y ajuste
Reensamblaje
Tense el cable para que no quede suelto. Deslice la abrazadera de ajuste [A] para ajustar la tensin del
cable.
[B]: Correcto
[C]: No correcto
Pg.175)
190
x 2, muelle x 1,
x 1, correa dentada x 1)
Asegrese de que la placa de tierra [B] est conectada al instalar el motor del escner en el
soporte del motor del escner.
Realice el ajuste de la imagen del escner despus de sustituir el motor del escner (
Pg.161 "Ajuste de la imagen").
Pg.184)
x 1,
x1,
x 1 cada uno)
191
4. Sustitucin y ajuste
x 2)
Durante el rearmado
Ajuste los siguientes modos SP despus de sustituir la unidad del circuito del sensor:
SP4008 (Ajuste de ampliacin de escaneado secundario): Consulte "Ajuste de imagen:
escaneado" (Pg.161 "Ajuste de la imagen").
SP4010 (Ajuste de registro de LE): Consulte "Ajuste de imagen: escaneado" (Pg.161 "Ajuste de
la imagen").
SP4011 (Ajuste de registro de lado a lado): Consulte "Ajuste de imagen: escaneado" (Pg.161
"Ajuste de la imagen").
SP4688 (DF: Density Adjustment): Este cdigo se utiliza para ajustar el nivel de densidad si el ID
de las copias realizadas en el DF y el modo cristal de exposicin son diferentes.
192
Pg.175)
x 2,
x 2)
Pg.175)
3. Mueva el primer carro del escner [A] a la derecha girando el motor del escner [B] en el sentido
de las agujas del reloj.
193
4. Sustitucin y ajuste
x 1, ganchos).
x 1)
Pg.175)
2. Panel de mandos (
Pg.177)
3. Cristal de exposicin (
194
Pg.184)
x 1)
x 2)
x 3)
x 5)
195
4. Sustitucin y ajuste
x 2).
x 8,
x todos,
Pg.190)
196
x todos)
x 1)
x 1)
197
4. Sustitucin y ajuste
x 1,
x 1).
198
6. Enganche el extremo derecho en el soporte del cable delantero del escner [A]. El extremo debe ir
por el carril trasero de la polea derecha [B] y el carril trasero de la polea mvil [C].
No fije el soporte del cable del escner con el tornillo todava.
199
4. Sustitucin y ajuste
8. Inserte un pasador de posicionamiento del escner [A] a travs del segundo orificio del carro [B] y
los orificios izquierdos [C] del ral delantero. Inserte otro pasador de posicionamiento del escner
[D] a travs del primer orificio del carro [E] y los orificios derechos del carril delantero [F].
9. Inserte dos pasadores de posicionamiento del escner ms por los orificios del carril trasero.
10. Fije la polea de accionamiento en el eje [G].
11. Fije el soporte del cable del escner en el carril delantero [H].
12. Instale la abrazadera del cable del escner [I].
13. Saque los pasadores de posicionamiento.
Compruebe que los carros primero y segundo se mueven suavemente despus de haber quitado
los pasadores de posicionamiento. En caso contrario, vuelva a realizar los pasos 8 a 13.
Pg.175)
2. Panel de mandos (
Pg.177)
3. Cristal de exposicin (
Pg.184)
8. Siga los pasos 10 al 14 en la Pg.194 "Cable delantero del escner". Puede extraer el cable del
escner posterior de la misma manera que para sustituir el escner delantero.
200
4
1. Coloque la bola central [A] en el centro del soporte bifurcado.
2. Pase el extremo izquierdo (con la bola) [B] a travs de la muesca de la polea de impulsin. Pase el
extremo derecho (con la anilla) a travs del orificio de la polea de accionamiento.
3. Enrolle cinco veces el extremo izquierdo [B] en sentido antihorario (desde la parte delantera de la
mquina). Enrolle tres veces el extremo derecho en sentido antihorario.
Las dos marcas verdes [C] quedan juntas al hacer esto. Fije el cable a la polea con cinta
adhesiva. De esta forma podr manejar fcilmente el conjunto en el momento de la instalacin.
4. Instale la polea de accionamiento en el eje.
No fije la polea al eje con el tornillo en este momento.
5. Instale el cable.
El bobinado del cable en las tres poleas de la parte trasera del escner debe ser igual que el
bobinado en las tres poleas de la parte delantera. Debe ser como una imagen especular.
Ejemplo: En la parte delantera de la mquina, el lateral de la polea de accionamiento con los tres
enrollados debe quedar orientado hacia la parte delantera de la mquina. En la parte trasera de la
mquina, debe quedar orientado hacia atrs.
6. Realice los pasos 7 al 13 de "Reinstalacin del cable delantero del escner" (Pg.194 "Cable
delantero del escner").
201
4. Sustitucin y ajuste
202
Cuando retire el cable trasero del escner, es necesario retirar la polea de temporizacin [A]
antes de mover el eje ( x 1).
ptica lser
ptica lser
Apague el interruptor principal y desenchufe la mquina antes de iniciar cualquiera de los
procedimientos de esta seccin. Los rayos lser pueden causar lesiones graves en los ojos.
Unidad lser
Antes de montar una nueva unidad lser, retire el soporte del motor poligonal y la etiqueta de la
nueva unidad.
203
4. Sustitucin y ajuste
4
1. Tapa del motor del espejo poligonal [A] de la unidad de lser (
x 4)
2. Pieza de fijacin del soporte del motor poligonal [B] con una etiqueta roja (
204
x 3)
ptica lser
x 4).
5. Ejecute SP2-220-003 para borrar el ajuste del motor de posicionamiento del espejo n. 2 para el
amarillo.
6. Salga del modo SP.
7. Apague el interruptor principal y desconecte el cable de corriente de la copiadora.
4. Sustitucin y ajuste
x 10)
206
x 2)
ptica lser
x 2,
x 2,
x 2,
x 1)
x 2,
x 1,
x 1)
x 3)
207
4. Sustitucin y ajuste
4. Introduzca los ajustes de SP en la hoja provista con una nueva unidad LD.
SP2-101-001 a -004: Registro de color: Escaneo principal para cada color
SP2-101-013 a -016: Registro de color: Escaneo secundario para cada color
SP2-102-001, -003, -004, -006, -007, -009, -010, -012: Ampliacin principal para cada
color y velocidad de lnea
SP2-104-001 a -004: Ajuste de potencia inicial del diodo lser para cada color
Los valores impresos [A] son distintos para cada unidad lser.
5. Imprima la trama de prueba (14: trama de recorte de 1 punto en el SP2-109-003).
6. Compruebe que los mrgenes de recorte izquierdo y derecho no sobrepasen 4 1 mm.En caso
contrario, cambie el valor estndar para el ajuste de ampliacin del escner principal.
7. Seleccione "0" con SP2-109-003 despus de imprimir la trama de recorte de 1 punto.
8. Haga el ajuste de posicin de lnea.
Ejecute primero SP2-111-003.
A continuacin, ejecute el SP2-111-001.
Para comprobar si el SP 2-111-001 se ha ejecutado correctamente, observe la pantalla durante
el proceso. Al final aparece un mensaje. Tambin puede comprobar el resultado con el SP
2-194-010 a -012.
9. Salga del modo SP.
208
Pg.203)
ptica lser
x 4,
x 4)
x 1)
x 1)
209
4. Sustitucin y ajuste
Creacin de imgenes
PCDU (Unidad fotoconductora y de revelado)
No toque el tambor del fotoconductor. No permita que ningn objeto metlico toque el manguito
de revelado.
1. Abra la puerta delantera.
2. Botella de recogida de tner de la PCDU (
Pg.172)
210
x 2 cada uno)
Creacin de imgenes
4
Retire la tapa [A] de la boquilla de tner y extraiga la cinta [B] de la nueva unidad de revelado antes de
instalar una nueva PCDU en la mquina.
211
4. Sustitucin y ajuste
Pg.210)
212
x 2)
x 2)
Creacin de imgenes
x 1)
Al retirar la unidad de revelado de la unidad del tambor, limpie la cinta mylar [A] con una
aspiradora.
4. Sustitucin y ajuste
Cuando se instala una nueva unidad de revelado en la mquina, la mquina reiniciar automticamente
los contadores de mantenimiento preventivo de la unidad de revelado y la unidad del tambor, incluso si
la unidad del tambor no se cambi. Para evitar el reinicio de ambos contadores despus de instalar slo
una nueva unidad de revelado, asegrese de realizar el paso 2 del procedimiento anterior antes de la
instalacin.
Pg.172)
Pg.179)
Pg.210)
Retire la PCDU del color correspondiente. Por ejemplo, si retira la unidad de tolva de tner: K,
retire la PCDU negra.
x 2,
x 1 para K y M; 2 para C ,
x 1 cada una)
Creacin de imgenes
Pg.172)
Pg.179)
Pg.210)
x 2,
x 2)
x 2,
x 1 cada una)
215
4. Sustitucin y ajuste
216
Creacin de imgenes
Pg.172)
Pg.179)
4. Bandeja interior (
Pg.182)
x 3).
NOTA
217
4. Sustitucin y ajuste
Cuando retire la unidad de engranaje de suministro de tner para amarillo, uno de los tornillos de
dicha unidad resulta difcil de ver.
1) Retire la tapa izquierda (
Pg.174).
4
2) Compruebe la posicin del tornillo [A] como se muestra anteriormente.
218
Creacin de imgenes
x 1,
x 1,
x 2)
NOTA
Aplique Grasa de silicona G501 al engranaje del motor. A continuacin se muestra la cantidad
adecuada de grasa.
4
El destornillador plano de la foto es de tamao pequeo.
Pg.172)
Pg.210)
4. Ventilador: delantero (
219
4. Sustitucin y ajuste
7. Engranajes [A] (
x 1)
220
x 2)
x 2,
x 3)
Creacin de imgenes
NOTA
Aplique Grasa de silicona G501 al engranaje del motor. A continuacin se muestra la cantidad
adecuada de grasa.
x 1,
x 1, ganchos)
221
4. Sustitucin y ajuste
Placa RFID
1. Todas las unidades de tolva de tner (
2. Bandeja interior (
Pg.214)
Pg.182)
222
x 1)
Creacin de imgenes
x 3,
x 1)
x 1)
223
4. Sustitucin y ajuste
Transferencia de imgenes
Unidad de limpieza de la ITB
Si cambia la unidad de limpieza o la botella de recogida de tner despus de que la mquina detecte
que est llena o casi llena, la mquina restablecer automticamente el contador de mantenimiento
preventivo de la botella.
Sin embargo, si cambia una botella que no est llena o casi llena, deber restablecer el contador PM de
esta unidad. Para hacerlo, ajuste los SP 3902-017 y -020 a 1 antes de apagar el interruptor.
x 2)
x 2).
Transferencia de imgenes
Pg.174)
x 1,
x 1,
x 1)
Pg.224)
Pg.172)
Pg.289)
225
4. Sustitucin y ajuste
x 1).
x 1)
8. Sujete las asas [A] y tire hacia fuera por completo de la unidad de la ITB [B] (
x 2,
x 1).
9. Retire el motor de la unidad de la ITB despus de tirar hacia fuera de la unidad de la ITB de la
mquina. ( "Procedimiento siguiente")
Si, tras haberla retirado de la mquina, tarda mucho tiempo en volver a instalar la unidad ITB, cierre
la unidad de transferencia de papel para evitar que las unidades de tambor queden expuestas a la
luz.
226
Pg.225)
Pg.224)
Transferencia de imgenes
x 3,
x 1)
Pg.224)
Pg.225)
Pg.226)
x 2 cada uno)
227
4. Sustitucin y ajuste
5. Pieza de fijacin del soporte delantero [A] (como se ve desde la parte delantera) (
6. Pieza de fijacin del soporte trasero [A] (como se ve desde la parte trasera) (
7. Asa [A] (
228
x 2: M3x10)
x 1: M3x10)
x 1: M3x10)
Transferencia de imgenes
x 1)
x 2)
229
4. Sustitucin y ajuste
12. Fije el asa [A], que se retir en el paso 7, al saliente [B] en el lado posterior izquierdo (
El asa se utilizar como una base en pasos posteriores.
230
x 1).
Transferencia de imgenes
Hay un cerco [A] en cada borde de la banda de transferencia. Los extremos de todos los rodillos
([B] por ejemplo) de la unidad de banda de transferencia deben estar entre los dos cercos.
Hay dos cercos (anchura [C]: unos 5 mm) en los bordes frontal y trasero dentro de la unidad
de banda de transferencia de imagen.
Esta banda debe instalarse correctamente. Cuando vuelva a instalar la unidad de banda de
transferencia de imagen, hgalo con la marca blanca [A] en la banda en la parte trasera de la
unidad.
Pg.182)
Pg.182)
231
4. Sustitucin y ajuste
x 2)
5. Desconecte dos mazos de cables [A], y luego retire la unidad del motor de contacto de la ITB (
1)
6. Engranajes [A] (
232
x 1)
Transferencia de imgenes
x 2)
NOTA
Aplique Grasa de silicona G501 al engranaje del motor. A continuacin se muestra la cantidad
adecuada de grasa.
4
El destornillador plano de la foto es de tamao pequeo.
233
4. Sustitucin y ajuste
Si no se puede abrir la unidad de transferencia de papel, aguante la unidad PTR con la mano
como se muestra anteriormente y libere con mucho cuidado la palanca de tensin delantera
234
[A] de la unidad PTR. En este caso, la palanca de apertura de la unidad PTR [B] no funciona a
la hora de abrir la unidad PTR.
La tensin del resorte de la palanca de tensin es muy fuerte. Tenga mucho cuidado al liberar
la palanca de tensin. En caso contrario, podra lesionarse la mano o los dedos.
Pg.289)
235
4. Sustitucin y ajuste
4
2. Libere el brazo [A] (
x 1).
Placa de sensores de DI
1. Unidad dplex (
Pg.289)
236
x 2)
x 6, ,
x 1,
x 1)
Si el espaciador negro [B] est fijado en la placa del sensor como se muestra anteriormente,
retire todos los espaciadores negros. Estos espaciadores negros deben utilizarse cuando se
instale una nueva placa de sensor de DI.
Pg.210)
Pg.225)
4. Sustitucin y ajuste
3. Introduzca todos los coeficientes de correccin [A] para el sensor de DI con los modos SP consultando
la hoja de cdigos de barras facilitada con la nueva unidad/placa de sensores de DI.
Por ejemplo, introduzca " 0,98 " con SP3-362-013.
4. Salga del modo SP.
238
Pg.178)
Pg.179)
x 1).
x 3,
4
x todos)
7. Resorte [A]
No olvide reinstalar el resorte [A] cuando proceda al reensamblaje. De lo contrario, se
producir SC400.
8. Soporte del motor de contacto del PTR [B] (
x 3)
239
4. Sustitucin y ajuste
9. Engranaje [A] (
x 1, cojinete x 1)
x 2,
x 3)
NOTA
Aplique Grasa de silicona G501 al engranaje del motor. A continuacin se muestra la cantidad
adecuada de grasa.
240
x 2,
x 1)
Pg.176)
x 1,
x 1,
x 1)
241
4. Sustitucin y ajuste
Unidad de accionamiento
6. Motor de tambor/revelado: K
7. Motor de alimentacin del papel: T1
8. Motor de alimentacin del papel: T2
9. Motor de registro
Motor bypass
Unidad de engranajes
1. Tapa posterior (
242
Pg.175)
Unidad de accionamiento
Pg.175)
4
4. Retire todos los conectores y abrazaderas (flechas azules) en el HVPS: placa CB [A].
5. Tire de todas las PCDU hacia el lado delantero. (
x todos,
Pg.210)
x 8)
Es necesario el destornillador corto (190 mm o menos de longitud total) para quitar el tornillo
[B].
243
4. Sustitucin y ajuste
Motor de registro
1. Tapa posterior (
Pg.175)
Pg.175)
x 2,
x 1)
Es necesario el destornillador corto (190 mm o menos de longitud total) para retirar el tornillo
[B]
La siguiente imagen muestra cmo retirar el tornillo [C] de la unidad de engranajes. La caja del
controlador debe estar cerrada en este momento.
244
Unidad de accionamiento
4
Motor de alimentacin de papel: T1
1. Tapa posterior (
Pg.175)
Pg.175)
x 1,
x 2)
La siguiente imagen muestra cmo retirar el tornillo [B] del motor de alimentacin de papel T1.
245
4. Sustitucin y ajuste
4
Motor de alimentacin de papel: T2
1. Tapa inferior posterior (
Pg.175)
x 1,
x 2)
Pg.175)
Pg.175)
246
Unidad de accionamiento
x 3,
x 1)
Pg.175)
Pg.175)
x 3,
x 1)
Motor de tambor/revelado: K
1. Tapa posterior (
Pg.175)
Pg.175)
247
4. Sustitucin y ajuste
x 3,
x 1)
Embrague de revelado: K
1. Tapa posterior (
Pg.175)
Pg.175)
Pg.175)
Pg.175)
x 2,
x 1,
x 1)
Unidad de accionamiento
4
4. Afloje el anclaje [A] (
x 1, gancho [B] x 1)
El gancho [B] est instalado como se muestra anteriormente. No tire del anclaje con fuerza o
el gancho podra romperse.
x 3,
x 1)
La siguiente imagen muestra cmo retirar el tornillo [B] del motor de fusin/salida de papel.
249
4. Sustitucin y ajuste
250
Fusin
Fusin
Unidad de fusin
Apague el interruptor principal y espere a que se enfre la unidad de fusin antes de iniciar cualquiera
de los procedimientos de esta seccin. La unidad de fusin puede provocar quemaduras graves.
1. Abra la unidad dplex.
251
4. Sustitucin y ajuste
Si la unidad de fusin est adherida a la unidad PTR y no puede retirarse de la mquina, mantenga su
mano sujetando la unidad PTR como se muestra anteriormente y libere con mucho cuidado la palanca de
tensin delantera [A] de la unidad PTR. En este caso, la palanca de apertura de la unidad PTR [B] no
funciona a la hora de abrir la unidad PTR.
La tensin del resorte de la palanca de tensin es muy fuerte. Tenga mucho cuidado al liberar la
palanca de tensin. En caso contrario, podra lesionarse la mano o los dedos.
Asegrese de que ambas palancas de bloqueo [B] estn bloqueadas antes de cerrar la unidad dplex.
De lo contrario, ambas palancas [B] pueden romperse.
Pg.251)
x 2)
Requisitos de limpieza
La placa gua de entrada requiere mantenimiento de limpieza cada intervalo de 60 K. Limpie la placa
gua de entrada con un pao humedecido con alcohol en los siguientes puntos.
252
Fusin
Placa separadora
1. Unidad de fusin (
Pg.251)
253
4. Sustitucin y ajuste
x 4)
4. Retire los anillos de retencin [A] de la parte delantera y trasera, y luego los resortes [B] de la parte
delantera y trasera.
254
Fusin
Requisitos de limpieza
La placa separadora requiere mantenimiento de limpieza cada intervalo de 60 K. Limpie la placa
separadora con un pao humedecido con alcohol en los siguientes puntos.
Pg.251)
255
4. Sustitucin y ajuste
3. Limpie la placa gua de salida [A] con un pao humedecido con alcohol.
Pg.251)
256
Pg.253)
Fusin
x 2)
5. Aplique "Barrierta S552R" a los ejes de los engranajes [A] de la unidad de fusin. Anteriormente se
muestra la cantidad adecuada de grasa. El destornillador plano [B] de la foto es de tamao pequeo.
Pg.251)
257
4. Sustitucin y ajuste
x 2).
x 2)
x 2).
x 2)
Pg.251)
258
Pg.257)
Fusin
x 3)
x 2)
x 4)
Algunos cables todava estn conectados a la unidad de fusin en este momento. No someta
a ninguna tensin los cables conectados durante este procedimiento.
259
4. Sustitucin y ajuste
7. Deslice los rebordes delantero y trasero [A] hacia los lados exteriores para desconectarlos de los
soportes del rodillo de calentamiento delantero y trasero.
8. Sujete ambos rebordes en el lado delantero y trasero de la unidad del rodillo de calentamiento [A],
y luego tire de la unidad del rodillo de calentamiento [A].
260
Fusin
4
Asegrese de que el reborde con la marca F [A] se coloca hacia el lado delantero de la unidad de
fusin cuando reinstale la unidad del rodillo de calentamiento.
Rodillo de presin
Procedimiento de limpieza
El rodillo de presin requiere mantenimiento de limpieza (si est sucio) a intervalos de 60 K.
1. Unidad de fusin (
Pg.251)
261
4. Sustitucin y ajuste
Limpie ambos extremos [C] del rodillo de presin as como el rea central.
Procedimiento de sustitucin
1. Unidad del rodillo de calentamiento (
Pg.258)
x 2)
262
Fusin
Aplique "Barrierta S552R" al borde delantero [A] y al borde trasero [B] del rodillo de presin como
se muestra anteriormente.
263
4. Sustitucin y ajuste
x 2)
Pg.258)
x 2 cada uno)
Fusin
x 1,
x 1)
x 1)
Requisitos de limpieza
El termistor del rodillo de calentamiento requiere mantenimiento de limpieza a intervalos de 60 K. Limpie
el termistor del rodillo de calentamiento con un pao seco.
Pg.251)
265
4. Sustitucin y ajuste
x 1,
x 1)
x 1)
Pg.251)
266
Fusin
x 1,
x 1)
x 1)
Requisitos de limpieza
Los termistores del rodillo de presin (centro y extremo) requieren mantenimiento de limpieza cada
intervalo de 60 K. Limpie los termistores del rodillo de presin (centro y extremo) con un pao seco.
Termopila
1. Unidad de fusin (
Pg.251)
267
4. Sustitucin y ajuste
3. Termopila [A] (
x 2,
x 1)
x 1)
Realice este procedimiento de limpieza despus de que la unidad de fusin se haya enfriado
completamente. De lo contrario, podra quemarse de gravedad.
1. Unidad de fusin (
268
Pg.251)
Fusin
Pg.251)
x 4)
269
4. Sustitucin y ajuste
x 2)
270
x 2)
4
1. Saque la pieza de la bandeja de papel 1 o 2 [A].
2. Retire dos tornillos de ambas guas de la bandeja.
3. Saque la bandeja de papel 1 o 2 [A].
Rodillo de alimentacin
Bandeja 1 y Bandeja 2
1. Bandeja de papel 1 o 2 (
Pg.271)
x 1).
271
4. Sustitucin y ajuste
Cojinete de friccin
1. Bandeja de papel 1 o 2 (
Pg.271)
2. Rodillo de alimentacin (
Pg.271)
x 1).
272
Asegrese de que el mylar [A] no quede debajo del cojinete de friccin cuando lo reinstale.
No toque el cojinete de friccin con las manos desnudas cuando lo reemplace. Si lo hace, limpie el cojinete
de friccin con un pao hmedo o alcohol.
Pg.271)
273
4. Sustitucin y ajuste
x 1)
Pg.271)
274
Pg.271)
x 1)
x 1)
Sensor de registro
1. Unidad dplex (
Pg.289)
Pg.235).
x 2)
275
4. Sustitucin y ajuste
x 2)
276
x 2, ganchos,
x 1,
x 1)
x 4)
Limpie el rodillo de registro y el rodillo inactivo de registro [A] con un pao hmedo cada 60 K (recuento
total).
No utilice nunca alcohol para limpiar el rodillo de registro.
Pg.289)
277
4. Sustitucin y ajuste
x 2)
278
x 4,
x 2,
x 1)
x 1,
x 1)
x 1, ganchos)
Pg.289)
279
4. Sustitucin y ajuste
x 2)
x 1)
280
x 1)
Salida de papel
Salida de papel
Ventilador con solenoide de compuerta de unin
1. Tapa superior derecha (
2. Tapa trasera derecha (
Pg.180)
Pg.176)
x 1,
x 1)
)Pg.251)
Pg.179)
Pg.181)
Pg.182)
281
4. Sustitucin y ajuste
282
x 1)
x 1)
Salida de papel
4
8. Unidad de salida de papel [A]
Pg.281)
x 1,
x 1,
x 1)
283
4. Sustitucin y ajuste
x 1)
Pg.281)
284
x 1)
Salida de papel
4
Coloque la unidad de salida de papel de forma que [A] mire hacia arriba. De lo contrario, el detector
del sensor de salida del papel interrumpe la instalacin del sensor de salida de papel.
Inserte el gancho [B] primero.
Sensor de inversin
1. Unidad de salida de papel (
Pg.281)
285
4. Sustitucin y ajuste
Motor de inversin
1. Unidad de salida de papel (
286
Pg.281)
x1,
x 1)
Salida de papel
x 2,
x 1)
Pg.179)
x 2,
x 1,
x 1)
287
4. Sustitucin y ajuste
288
Asegrese de que el mazo de cables est correctamente instalado [A] a ras de la gua en el marco del
ventilador sin holgura [B]. De lo contrario, algunos de los cables podran pinzarse, daarse o cortarse
entre el marco del ventilador y el marco de la mquina principal. Puede emitirse SC533 si el mazo de
cables se rompe.
Unidad dplex
Unidad dplex
Unidad dplex
289
4. Sustitucin y ajuste
x 1 cada uno).
290
Pg.289)
Unidad dplex
x 2)
Levante la placa gua dplex [A] primero cuando vuelva a instalar la unidad de gua de entrada
dplex.
291
4. Sustitucin y ajuste
x 4)
4
5. Sensor de entrada dplex [A] (gancho)
Pg.289)
x 1)
x 1, tornillo de tierra x 1,
x 1,
x 1)
Unidad dplex
Pg.289)
x 3,
x1,
x 1)
293
4. Sustitucin y ajuste
x 2)
Pg.289)
x 3,
x 2,
x 2)
x 1)
Motor bypass
1. Unidad dplex (
Pg.289)
294
Unidad dplex
x 3,
x 2,
x 1)
x 2)
Pg.289)
295
4. Sustitucin y ajuste
x 2, gancho [B]).
Utilice un destornillador de cabeza plana o una herramienta similar para empujar el gancho
[B] hacia abajo.
296
Unidad dplex
x 2)
x 1)
Pg.295)
4. Sustitucin y ajuste
x 1)
298
Presentacin
Presentacin
A3 SEF
00001001
A5 SEF
00001110
Unidad dplex
B4 SEF
00001011
B6 SEF
00001100
A4 SEF
00000011
A6 SEF
00001101
B5 SEF
00000111
00001101
Pg.295)
x 1, gancho)
Pg.295)
4. Sustitucin y ajuste
4. Gire el accionador [A] en sentido contrario a las agujas del reloj como se muestra anteriormente.
5. Sensor de posicin inicial de bandeja bypass [B] (gancho).
300
Componentes elctricos
Componentes elctricos
Circuitos
Caja del controlador cerrada
[A]
BCU
[B]
[C]
IPU
[D]
DRB
[E]
[F]
PSU
301
4. Sustitucin y ajuste
4
[A]
[B]
Placa HVPS: CB
Pg.175)
x 3)
3. Afloje los cinco tornillos sealados por las marcas de flecha en la foto anterior.
4. Retire los tres tornillos [B] en la parte inferior de la caja del controlador.
5. Deslice la tapa de la caja del controlador [C] hacia arriba y retrela.
302
Componentes elctricos
Pg.175)
Pg.175)
Pg.302)
4. Retire los tres tornillos y desconecte el cable del escner [A] (tornillo de tierra x 1)
BCU
1. Tapa posterior (
Pg.175)
Pg.302)
303
4. Sustitucin y ajuste
4
3. BCU [A] (
x 7,
x todos)
Mantenga alejadas las NVRAM de cualquier objeto que pueda producir electricidad esttica. La
electricidad esttica puede daar los datos de la NVRAM.
304
Componentes elctricos
HDD
Si es posible, copie los datos de la libreta de direcciones en una tarjeta SD desde el HDD con
SP5846-051 antes de reemplazar el HDD.
1. Tapa posterior (
Pg.175)
Pg.302)
x 5,
x 2).
x 2,
x 4,
x 4)
6. HDD
4. Sustitucin y ajuste
2. Ejecute SP5853-001 para copiar los datos de sello prestablecido desde el firmware hasta el disco
duro.
3. Ejecute SP5846-052 para volver a copiar la libreta de direcciones en el disco duro desde la tarjeta
SD en la que ya se han copiado los datos de la libreta de direcciones.
4. Ejecute SP5-878-001 para instalar la aplicacin DataOverwriteSecurity.
5. Ejecute SP5878-002 para instalar la aplicacin de Cifrado del disco duro.
6. Apague el equipo.
No saque nunca una unidad de disco duro del lugar de trabajo sin el consentimiento del cliente.
Si el cliente est preocupado por la seguridad de la informacin contenida en el disco duro, ste
debe quedar en poder del cliente para que lo deseche o lo guarde en lugar seguro.
El disco duro puede contener informacin patentada o clasificada (Confidencial, Secreta).
Concretamente, el disco duro contiene documentos y datos del servidor de documentos almacenados
en archivos temporales creados automticamente durante la ordenacin de los trabajos de copia y
la recuperacin de atascos. Estos datos se almacenan en el disco duro en un formato especial, de
forma que no se puedan leer normalmente, pero pueden ser recuperados por mtodos ilegales.
Circuito IPU
1. Tapa posterior (
Pg.175)
306
Pg.302)
Pg.305 "HDD")
Componentes elctricos
x 6,
x todos)
Pg.175)
x 2,
x 2,
x 1,
x 1,
x 1)
x 1)
307
4. Sustitucin y ajuste
Pg.175)
308
x 2,
x 1,
x 1)
Componentes elctricos
DRB
1. Tapa posterior (
Pg.175)
3. DRB [A] (
x 6,
Pg.175)
x todos)
309
4. Sustitucin y ajuste
SDVDB
1. Tapa posterior (
Pg.175)
Pg.175)
4
3. SDVDB [A] (
x 3,
x 5)
PSU
1. Tapa posterior (
310
Pg.175)
Pg.175)
x 4,
x todos,
x todos)
Componentes elctricos
x 2)
x 9,
x Todos,
x Todos)
Pg.175)
x todos)
x 5,
Placa HVPS: CB
1. Tapa posterior (
Pg.175)
4. Sustitucin y ajuste
4
3. HVPS: placa CB [A] (
x 6, todos los
Pg.175)
312
Componentes elctricos
x 6)
4
5. Conjunto de la placa del controlador [A] (
x 7,
x 2)
6. Retire las tarjetas SD [A], rales de interfaz [B], NVRAM [C] y RAM-DIMM [D].
7. Placa del controlador [E]
313
4. Sustitucin y ajuste
Mantenga alejadas las NVRAM de cualquier objeto que pueda producir electricidad esttica. La
electricidad esttica puede daar los datos de la NVRAM.
Asegrese de que la NVRAM est correctamente instalada en la placa del controlador.
314
Componentes elctricos
Pg.305 "HDD").
x 1).
315
4. Sustitucin y ajuste
Borrado de la NVRAM
Cuando se reemplace la placa del controlador y un cliente haya perdido la clave de cifrado, es necesario
borrar la NVRAM para recuperar la unidad de cifrado del disco duro.
1. Prepare una tarjeta SD que se haya inicializado.
2. Cree la carpeta "restore_key" en la tarjeta SD.
SP5-990-001) si es posible.
316
SP5-824-001) si es posible.
Componentes elctricos
SP5-990-001) si es posible.
Pg.175)
x 2).
317
4. Sustitucin y ajuste
Desconectar los cables del disco duro es muy importante. De lo contrario, el disco duro se
formatea automticamente y todos los datos que contiene se pierden debido a la limitacin de
seguridad.
7. Instale una nueva NVRAM en el controlador. Monte de nuevo la mquina.
8. Quite la tapa de la ranura SD (
x 1).
318
Pg.137
Tablas SP
Los cdigos SP de uso ms frecuente se encuentran en las "Tablas SP principales -1 a 9-" de "Captulos
principales".
Consulte "Apndices" para obtener la siguiente informacin:
Tipos de modos SP
SP del sistema: modos SP relacionados con las funciones del motor
SP de la impresora: modos SP relacionados con las funciones de la impresora
SP del escner: modos SP relacionados con las funciones del escner
SP del fax: modos SP relacionados con las funciones del fax
Seleccione uno de los modos de Programa de servicio (Sistema, Impresora, Escner o Fax) en la pantalla
tctil como se indica en el diagrama siguiente despus de acceder al modo SP. Esta seccin explica las
funciones de los modos SP de Sistema/Impresora/Escner. Consulte el manual de servicio de fax para
los modos SP de Fax.
319
320
Si conoce el nmero de SP, escriba el cdigo de SP directamente con las teclas numricas.
Despus, pulse . (El nmero de modo SP requerido se resaltar al pulsar . De lo contrario,
pulse el nmero de modo SP necesario.)
Pulse dos veces para salir del modo SP y volver a la ventana de copia para reanudar el
funcionamiento normal.
Pulse cualquier nmero de Clase 1 para abrir una lista de los modos SP de Clase 2.
Pulse este botn para mostrar el grupo anterior o siguiente.
Pulse para desplazarse a la pantalla anterior o siguiente en segmentos del tamao de la pantalla
(pginas).
Pulse este botn para mostrar la lnea anterior o siguiente (lnea a lnea).
Pulse este botn para desplazar la opcin resaltada de la izquierda hasta la seleccinanterior
o siguiente de la lista.
4. Pulse Modo SP (resaltado) para volver a la pantalla del modo SP y repita el proceso desde el paso
1.
321
322
El tcnico del cliente puede realizar operaciones de servicio y encender y apagar la mquina.
No es necesario volver a pedir al administrador que inicie sesin cada vez que se encienda la
mquina.
1. Acceda al modo SP y configure SP5169 en "1" si debe utilizar los interruptores bit de la impresora.
2. Una vez terminadas las operaciones de servicio de la mquina:
Cambie SP5169 de "1" a "0".
Apague y encienda la mquina. Informe al administrador de que ha terminado de realizar
operaciones de servicio en la mquina.
El administrador activar de nuevo Service Mode Lock (Bloqueo del modo de servicio).
Notas
Presentacin en la pantalla del panel de mandos
El nmero mximo de caracteres que puede mostrar la pantalla del panel de mandos est limitado a 30
caracteres. Por este motivo, es necesario abreviar algunos de los modos mostrados en la pantalla. He
aqu las abreviaturas utilizadas para los modos SP cuando la descripcin completa tiene ms de 30
caracteres.
Gramaje del papel
Papel fino: 52-59 g/m2 (14-16 lb. Bond)
Papel normal 1: 60-74 g/m2 (16-20 lb. Bond)
Papel normal 2: 75-81 g/m2 (20 lb. Bond)
Grueso medio: 82-105 g/m2 (20-28 lb. Bond)
Papel grueso 1: 106-169 g/m2 (28 lb. Bond-90 lb. Index)
Papel grueso 2: 170-210 g/m2 (65 lb. Cover-54 lb. Bond)
Papel grueso 3: 211-256 g/m2 (65 lb. Cover-54 lb. Bond)
Tipo de papel
N: Papel normal
GM: Papel de grueso medio
G: Papel grueso
323
Modo de impresin
Velocidad de proceso
S: Simple
D: Dplex
Otros
En las tablas de modos SP se utilizan los smbolos siguientes.
FA: Ajuste de fbrica
(Los datos pueden ajustarse desde los ajustes predeterminados en la fbrica. Consulte las hojas de
configuracin de fbrica incluidas. Las encontrar debajo de la etiqueta de eliminacin de papel
atascado.)
DFU: para uso de diseo/fbrica exclusivamente
No toque estos modos SP en las instalaciones del cliente.
Un signo de almohadilla (#) a la derecha de la columna del nmero de modo significa que es necesario
apagar y encender el interruptor principal para que el cambio de configuracin tenga efecto.
Un asterisco (*) a la derecha de la columna del nmero de modo significa que este modo se almacena
en la NVRAM. Si realiza un borrado de la RAM, el modo SP se reiniciar al valor predeterminado. ENG
y CTL indican qu NVRAM contiene los datos.
ENG: NVRAM de la placa BCU
CTL: NVRAM de la placa del controlador
La configuracin de cada modo SP se explica en la columna de la derecha de la tabla de SP, de la manera
siguiente.
[Intervalo ajustable / Configuracin predeterminada / Incrementos] Alfanumrico
Si se ha escrito Alfanumrico a la derecha del corchete, como se muestra arriba, la configuracin
del modo SP aparece en la pantalla con caracteres alfanumricos en lugar de slo con nmeros.
No obstante, las configuraciones entre corchetes de la tabla de modo SP se muestran slo mediante
nmeros.
SSP : Indica una configuracin de modo de Programa de servicio especial.
324
Tablas SP principales-1
Tablas SP principales-1
SP1-XXX (Alimentacin)
[Registro del borde anterior] Ajuste del registro del borde anterior
(Ubicacin de la bandeja, Tipo de papel, Modo de color), Tipo de papel -> Normal,
Grueso 1, Grueso 2 o Grueso 3
1001
Ajusta el registro del borde anterior cambiando la sincronizacin del funcionamiento del
motor de registro para cada modo.
Aumentar un valor: se mueve una imagen al borde de salida del papel.
Disminuir un valor: se mueve una imagen al borde anterior del papel.
001 Bandeja:Normal:600 dpi
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
325
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
006 Dplex
*ENG
326
Tablas SP principales-1
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[De -5 a 5 / 2 / 1 mm/incremento]
[De -5 a 5 / 0 / 1 mm/incremento]
[De -5 a 5 / 2 / 1 mm/incremento]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[De -5 a 5 / 0 / 1 mm/incremento]
327
1007
001
*ENG
1101
Especifica los ajustes del permiso de recarga para la temperatura fra en el modo de color.
Destino: NA; Norteamrica, TWN; Taiwn, EU; Europa, AA; Asia Pacfico
001
*ENG
[De 0 a 75 / 50 / 1 grado/incremento]
Temp. objetivo
002 recarga:Centro
*ENG
*ENG
*ENG
*ENG
*ENG
006 Especifica la correccin de temperatura del rodillo de presin cuando la unidad de fusin
se determina como estado fro.
328
Tablas SP principales-1
Tiempo de rotacin:Fro
*ENG
009
*ENG
*ENG
*ENG
010 Especifica la correccin de temperatura del rodillo de presin cuando la unidad de fusin
se determina como estado medio
Tiempo:Media
*ENG
013
*ENG
*ENG
*ENG
014 Especifica la correccin de temperatura del rodillo de presin cuando la unidad de fusin
se determina como estado caliente.
Tiempo:Calor
*ENG
329
Temp.:Delta:Fra:BN:Centro
016
*ENG
017
*ENG
*ENG
018 Especifica la correccin de temperatura del rodillo de presin en el modo blanco y negro
cuando la unidad de fusin se determina como estado fro.
Tiempo de rotacin:B/N:Fro
*ENG
020
021
022
023
330
Temp.:Delta:Media:B/
N:Centro
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-1
024
025
026
027
Temp.:Delta:Caliente:B/
N:Centro
*ENG
*ENG
*ENG
*ENG
*ENG
[0 o 1 / 0 /-]
101
TemTemp.:Delta:Fra:BN2:C
entro
*ENG
102
Temp.:Delta:Fra:BN2:Extrem
o
*ENG
103
Temp.:Delta:Fra: B/N
2:Presin
*ENG
104
*ENG
105
Temp.:Delta:Media: B/N
2:Centro
*ENG
106
Temp.:Delta:Media: B/N
2:Extremo
*ENG
107
Temp.:Delta:Media: B/N
2:Presin
*ENG
331
108
*ENG
109
Temp.:Delta:Caliente: B/N
2:Centro
*ENG
110
Temp.:Delta:Caliente: B/N
2:Extremo
*ENG
111
Temp.:Delta:Caliente: B/N
2:Presin
*ENG
112
*ENG
332
*ENG
*ENG
*ENG
*ENG
[De 0 a 50 / 15 / 1 grado/incremento]
*ENG
*ENG
007
Temp.:Delta
inferior:Centro:Especial1
*ENG
008
Temp.:Delta
inferior:Extremo:Especial1
*ENG
009
Temp.:Delta
superior:Centro:Especial1
*ENG
[De 0 a 50 / 15 / 1 grado/incremento]
010
Temp.:Delta
superior:Extremo:Especial1
*ENG
[De 0 a 50 / 15 / 1 grado/incremento]
Tablas SP principales-1
011
Temp.:Delta
inferior:Presin:Especial1
*ENG
*ENG
013
Temp.:Delta
inferior:Centro:Especial2
*ENG
014
Temp.:Delta
inferior:Extremo:Especial2
*ENG
015
Temp.:Delta
superior:Centro:Especial2
*ENG
[De 0 a 50 / 20 / 1 grado/incremento]
016
Temp.:Delta
superior:Extremo:Especial2
*ENG
[De 0 a 50 / 20 / 1 grado/incremento]
017
Temp.:Delta
inferior:Presin:Especial2
*ENG
*ENG
019
Tiempo de permiso de
alimentacin
*ENG
020
Temp.:Delta
inferior:Centro:Especial3
*ENG
021
Temp.:Delta
inferior:Extremo:Especial3
*ENG
022
Temp.:Delta
superior:Centro:Especial3
*ENG
[De 0 a 50 / 10 / 1 grado/incremento]
023
Temp.:Delta
superior:Extremo:Especial3
*ENG
[De 0 a 50 / 10 / 1 grado/incremento]
024
Temp.:Delta
inferior:Presin:Especial3
*ENG
*ENG
333
*ENG
*ENG
002 Especifica la temperatura objetivo del rodillo de presin para la condicin de lista en
impresin a todo color.
Normal1:BN:Centro
003
*ENG
Especifica la temperatura objetivo del rodillo de calor para la condicin de lista en impresin
en BN.
Normal1:BN:Presin
*ENG
004 Especifica la temperatura objetivo del rodillo de presin para la condicin preparada en
impresin en BN.
Normal2:FC:Centro
005
*ENG
*ENG
006 Especifica la temperatura objetivo del rodillo de presin para la condicin de lista en
impresin a todo color.
Normal2:BN:Centro
007
334
*ENG
Especifica la temperatura objetivo del rodillo de calor para la condicin de lista en impresin
en BN.
Tablas SP principales-1
Normal2:BN:Presin
*ENG
008 Especifica la temperatura objetivo del rodillo de presin para la condicin preparada en
impresin en BN.
009 Fino:FC:Centro
*ENG
010 Fino:FC:Presin
*ENG
011 Fino:BN:Centro
*ENG
012 Fino:BN:Presin
*ENG
*ENG
*ENG
*ENG
*ENG
017 Grueso:FC:Centro
*ENG
018 Grueso1:FC:Presin
*ENG
019 Grueso1:BN:Centro
*ENG
020 Grueso1:BN:Presin
*ENG
021 Grueso2:FC:Centro
*ENG
022 Grueso2:FC:Presin
*ENG
023 Grueso2:BN:Centro
*ENG
024 Grueso2:BN:Presin
*ENG
025 Grueso3:FC:Centro
*ENG
026 Grueso3:FC:Presin
*ENG
027 Grueso3:BN:Centro
*ENG
028 Grueso3:BN:Presin
*ENG
029 Especial1:FC:Centro
*ENG
030 Especial1:FC:Presin
*ENG
031 Especial1:BN:Centro
*ENG
335
336
032 Especial1:BN:Presin
*ENG
033 Especial2:FC:Centro
*ENG
034 Especial2:FC:Presin
*ENG
035 Especial2:BN:Centro
*ENG
036 Especial2:BN:Presin
*ENG
037 Especial3:FC:Centro
*ENG
038 Especial3:FC:Presin
*ENG
039 Especial3:BN:Centro
*ENG
040 Especial3:BN:Presin
*ENG
041 Sobre:Centro
*ENG
042 Sobre:Presin
*ENG
101
Normal1:FC:Centro:Baja
velocidad
*ENG
102
Normal1:FC:Presin:Baja
velocidad
*ENG
103
Normal1:BN:Centro:Baja
velocidad
*ENG
104
Normal1:BN:Presin:Baja
velocidad
*ENG
105
Normal2:FC:Centro:Baja
velocidad
*ENG
106
Normal2:FC:Presin:Baja
velocidad
*ENG
107
Normal2:BN:Centro:Baja
velocidad
*ENG
108
Normal2:BN:Presin:Baja
velocidad
*ENG
109
Fino:FC:Centro:Baja
velocidad
*ENG
Tablas SP principales-1
110
Fino:FC:Presin:Baja
velocidad
*ENG
111
Fino:BN:Centro:Baja
velocidad
*ENG
112
Fino:BN:Presin:Baja
velocidad
*ENG
113
Grueso M:FC:Centro:Baja
velocidad
*ENG
114
Grueso M:FC:Presin:Baja
velocidad
*ENG
115
Grueso M:B/N:Centro:Baja
velocidad
*ENG
116
Grueso M:B/N:Presin:Baja
velocidad
*ENG
117
Especial1:FC:Centro:Baja
velocidad
*ENG
118
Especial1:FC:Presin:Baja
velocidad
*ENG
119
Especial1:BN:Centro:Baja
velocidad
*ENG
120
Especial1:BN:Presin:Baja
velocidad
*ENG
121
Especial2:FC:Centro:Baja
velocidad
*ENG
122
Especial2:FC:Presin:Baja
velocidad
*ENG
123
Especial2:BN:Centro:Baja
velocidad
*ENG
124
Especial2:BN:Presin:Baja
velocidad
*ENG
125
Especial3:FC:Centro:Baja
velocidad
*ENG
337
126
Especial3:FC:Presin:Baja
velocidad
*ENG
127
Especial3:B/N:Centro:Baja
velocidad
*ENG
128
Especial3:B/N:Presin:Baja
velocidad
*ENG
131 OHP:Centro
*ENG
132 OHP:Presin
*ENG
338
134
Sobre:Presin:Baja
velocidad
*ENG
135 Normal1:Brillo:Centro
*ENG
136 Normal1:Brillo:Presin
*ENG
137 Normal2:Brillo:Centro
*ENG
138 Normal2:Brillo:Presin
*ENG
*ENG
*ENG
141 Especial4:FC:Centro
*ENG
142 Especial4:FC:Presin
*ENG
143 Especial4:B/N:Centro
*ENG
144 Especial4:B/N:Presin
*ENG
145 Especial5:FC:Centro
*ENG
146 Especial5:FC:Presin
*ENG
147 Especial5:B/N:Centro
*ENG
148 Especial5:B/N:Presin
*ENG
149 Especial6:FC:Centro
*ENG
150 Especial6:FC:Presin
*ENG
Tablas SP principales-1
151 Especial6:B/N:Centro
*ENG
152 Especial6:B/N:Presin
*ENG
153 Sobre:Centro:Grueso1
*ENG
154 Sobre:Presin:Grueso1
*ENG
155 Sobre:Centro:Grueso2
*ENG
156 Sobre:Presin:Grueso2
*ENG
157 Sobre:Centro:Grueso3
*ENG
158 Sobre:Presin:Grueso3
*ENG
1106
001 Centro
002 Final
El rodillo de calentamiento tiene dos lmparas. Una calienta el centro del rodillo y la otra,
ambos extremos.
003 Centro de presin
001
002
*ENG
*ENG
339
Precalentamiento2: Centro
*ENG
003 Especifica la temperatura del rodillo de calentamiento para el modo de ahorro de energa
2.
004
005
006
007
008
1108
001
002
1111
Precalentamiento2:Presin
*ENG
*ENG
*ENG
*ENG
*ENG
Especifica la temperatura del rodillo de presin para la condicin de lista para imprimir.
Temp. objetivo tras recarga/trabajo
Centro
*ENG
*ENG
*ENG
*ENG
340
Tablas SP principales-1
*ENG
[De 0 a 15 / 5 / 1 grado/incremento]
*ENG
[De 0 a 15 / 0 / 1 grado/incremento]
*ENG
007
*ENG
*ENG
001 Especifica el nivel de temperatura substractiva 1 del control de temperatura de fusin para
imgenes de trabajos variables.
Temp.:Normal:Centro:Nivel2 *ENG
004
[Entor. correcto:Fusin]
Correccin baja temp .
*ENG
[De 0 a 15 / 5 / 1 grado/incremento]
*ENG
[De 0 a 15 / 5 / 1 grado/incremento]
341
*ENG
*ENG
001
Correccin de ondulacin
Ejecutar patrn
*ENG
[De 0 a 2 / 0 / 1 /incremento]
0: Off, 1: On
*ENG
*ENG
*ENG
*ENG
342
*ENG
Tablas SP principales-1
CPM:Humedad media
*ENG
008 Especifica el ratio de CPM del control de alisado con respecto a la operacin normal en
humedad media.
CPM:Humedad-H
*ENG
009 Especifica el ratio de CPM del control de alisado con respecto a la operacin normal en
humedad alta.
1115
001
1132
*ENG
*ENG
[De 0 a 2 / 0 / 1 /incremento]
0: Servicio fijo, 1: Control energtico
001 Nmero SC
Causa SC
*ENG
*ENG
[De 0 a 9 / - / 1/incremento]
*ENG
343
5
107
*ENG
106
105
*ENG
*ENG
*ENG
*ENG
151
*ENG
344
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-1
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
1142
001
*ENG
[0 o 1 / 0 /-]
0: ACTIVADO, 1: DESACTIVADO
*ENG
*ENG
*ENG
005
*ENG
010
Tiempo:Divisin de
almacenamiento de calor1
*ENG
Tiempo:Divisin de
almacenamiento de calor2
*ENG
346
*ENG
*ENG
003 Bk OpcDevMot:120
*ENG
004 Bk OpcDevMot:60:Grueso
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[De -4 a 4 / 0 / 0,01%/incremento]
*ENG
[De -4 a 4 / 0 / 0,01%/incremento]
Tablas SP principales-1
011 Alimentacin1:CW60:Grueso
*ENG
012 Alimentacin1:CW120
*ENG
013 Alimentacin1:CCW60:Grueso
*ENG
014 Alimentacin1:CCW120
*ENG
015 Alimentacin12:CW60:Grueso
*ENG
016 Alimentacin12:CW120
*ENG
017 Alimentacin12:CCW60:Grueso
*ENG
018 Alimentacin12:CCW120
*ENG
019 Bypass:60:Grueso
*ENG
020 Bypass:120
*ENG
021 Inversor:CW60:Grueso
*ENG
022 Inversor:CW120
*ENG
023 Inversor:CCW60:Grueso
*ENG
024 Inversor:CCW120
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[De -2 a 2 / 0 / 0,05%/incremento]
*ENG
[0 a 1/1/1]
031 Disminucin:120:Color
*ENG
032 Disminucin:60:Color
*ENG
*ENG
5
[De -2 a 2 / 0 / 0,05%/incremento]
[-7 a 7 / 0 / 1 paso]
[De -4 a 4 / 0,3 / 0,05%/incremento]
347
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[De -4 a 4 / 0 / 0,01%/incremento]
[De -2 a 2 / 0 / 0,05%/incremento]
1803
348
Estos SP pueden ajustar el error de ampliacin de escaneo secundario. Sin embargo, lea
primero la "Gua de deteccin de errores" (Captulos principales) para ejecutar estos SP.
NUNCA EJECUTE estos SP antes de leer el "Error de ampliacin de escaneado secundario".
De lo contrario, se producen errores de registro de color en las salidas y no se pueden
recuperar mediante un ajuste de la posicin de la lnea.
*ENG
*ENG
003 Grueso:entrada
*ENG
*ENG
*ENG
006 Grueso:resultado
*ENG
[De -1 a 1 / 0 / 0,1%/incremento]
[De 0 a 0 / 2 / 1/incremento]
0: Correcto, 1: Error
Tablas SP principales-2
Tablas SP principales-2
SP2-XXX (Tambor)
2013
[Ambient. correcto:PCU]
Muestra el estado ambiental, que se mide
en humedad absoluta.
[De 1 a 5 / - / 1/incremento]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
349
2101
Estos valores son los parmetros para el ajuste automtico de posicin de lnea y se ajustan
en fbrica. Sin embargo, debe introducir un valor para SP2101-001 despus de
reemplazar la unidad de carcasa de las pticas lser. Para obtener detalles, consulte la
seccin "Sustitucin y ajuste". El valor debera suministrarse con la nueva unidad de carcasa
de las pticas lser.
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[Ajuste de ampliacin]
2102
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
2103
350
Estos valores son los parmetros para el ajuste automtico de posicin de lnea y se ajustan
en fbrica. Estos SP slo se deben introducir al instalar una nueva unidad lser.
Tablas SP principales-2
*ENG
*ENG
003 izquierdo
*ENG
004 derecho
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
012
*ENG
013
*ENG
*ENG
*ENG
Ajusta la potencia LD inicial. Estos SP slo se deben introducir al instalar una nueva unidad
lser.
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 S
*ENG
[Trama de prueba]
2109
351
Seleccin de patrn
[De 0 a 23 / 0 / 1/incremento]
0 Ninguno
1: Lnea vertical (1 punto)
3: Horizontal (1 punto)
4: Horizontal (2 puntos)
006 Densidad: Bk
0: Densidad ms clara
2111
002 Ejecutar:Modo b
352
Tablas SP principales-2
2112
001 Ejecutar
[Ajuste de desplazamiento]
2117
Estos SP deben utilizarse cuando se instala una nueva unidad de alojamiento de la ptica
lser, consulte la seccin "Sustitucin y ajuste".
001 Pulso: C
*ENG
002 Pulso: M
*ENG
003 Pulso: Y
*ENG
2118
[Ajuste de desplazamiento]
*ENG
002 Ejecutar:M
*ENG
003 Ejecutar:Y
*ENG
2119
001 C
*ENG
002 M
*ENG
003 S
*ENG
353
Muestra los mximos valores del resultado de la comprobacin del sensor de ID.
Delantero, Central, Posterior: sensores de ID del ajuste de posicin de lnea automtico y
el control de proceso
001 PWM
*ENG
*ENG
*ENG
*ENG
Muestra los mximos valores del resultado de la comprobacin del sensor de ID.
Delantero, Central, Posterior: sensores de ID del ajuste de posicin de lnea automtico y
el control de proceso
001 Promedio
*ENG
*ENG
*ENG
*ENG
Muestra los mximos valores del resultado de la comprobacin del sensor de ID.
Delantero, Central, Posterior: sensores de ID del ajuste de posicin de lnea automtico y
el control de proceso
354
Tablas SP principales-2
001 Mximo
*ENG
*ENG
*ENG
*ENG
Muestra los mnimos valores del resultado de la comprobacin del sensor de ID.
Delantero, Central, Posterior: sensores de ID del ajuste de posicin de lnea automtico y
el control de proceso
001 Mnimo
*ENG
*ENG
*ENG
*ENG
Muestra los 2 valores mximos del resultado de la comprobacin del sensor de ID.
Delantero, Central, Posterior: sensores de ID del ajuste de posicin de lnea automtico y
el control de proceso
001 Mximo 2:
*ENG
*ENG
*ENG
*ENG
355
Muestra los 2 valores mnimos del resultado de la comprobacin del sensor de ID.
Delantero, Central, Posterior: sensores de ID del ajuste de posicin de lnea automtico y
el control de proceso
001 Mnimo 2
*ENG
*ENG
*ENG
*ENG
2193
[Condicin de MUSIC]
Ajuste de posicin de lnea: Configuracin de condicin
Pgina:Fin trabajo:FC
*ENG
003 Ajusta el umbral para el ajuste de posicin de lnea para el modo de impresin de color
despus de finalizar un trabajo.
004
2194
356
*ENG
Ajusta el umbral del ajuste de posicin de lnea para el modo de impresin en BN y color
durante un trabajo.
[Resultado de ejecucin de MUSIC] Ajuste de posicin de lnea: Resultado de ejecucin
001 Ao
*ENG
[De 0 a 99 / 0 / 1 ao/incremento]
002 Mes
*ENG
[De 1 a 12 / 1 / 1 mes/incremento]
003 Fecha
*ENG
[De 1 a 31 / 1 / 1 da/incremento]
004 Hora
*ENG
[De 0 a 23 / 0 / 1 hora/incremento]
005 Minuto
*ENG
[De 0 a 59 / 0 / 1 minuto/incremento]
006 Temperatura
*ENG
*ENG
[0 o 1 / 0 / 1 /incremento]
0: Realizado correctamente, 1: Error
Tablas SP principales-2
*ENG
*ENG
*ENG
[De 0 a 9 / 0 / 1/incremento]
*ENG
0: No realizado
1: Realizado correctamente
2: No se pueden detectar las tramas
*ENG
Estos SP se deben ejecutar si se instala una nueva unidad de carcasa ptica lser. Para
obtener detalles, consulte "Unidad lser" en la seccin "Sustitucin y ajuste".
001 C: Motor de inclinacin
*ENG
*ENG
*ENG
2241
[Humedad/Temperatura ambiente:Pantalla]
Muestra la temperatura y la humedad ambiental.
001 Temperatura
2326
001
*ENG
Ajusta el voltaje positivo del rodillo de transferencia de papel para limpiar el rodillo de
transferencia de papel.
357
002
003
004
Negativo:antes y despus
de TRABAJO
*ENG
Ajusta el voltaje negativo del rodillo de transferencia de papel para limpiar el rodillo de
transferencia de papel.
Positivo:despus de
ATASCO
*ENG
Ajusta el lmite de corriente negativa del rodillo de transferencia de papel para limpiar el
rodillo de transferencia de papel.
Negativo:despus de
ATASCO
*ENG
001
003
Transferencia de imgenes:Velocidad
normal
*ENG
[De 0 a 60 / 25 / 1 A]
*ENG
[De 0 a 60 / 13 / 1 A]
2357
001
358
*ENG
[De 0 a 60 / 23 / 1 A]
Tablas SP principales-2
002
003
004
009
010
011
012
*ENG
[De 0 a 60 / 22 / 1 A]
*ENG
[De 0 a 60 / 25 / 1 A]
Ajusta la corriente para la banda de transferencia de imagen para Cian en el modo a todo
color para papel normal.
Transferencia de imgenes: Veloc.
normal:Y
*ENG
[De 0 a 60 / 29 / 1 A]
*ENG
[De 0 a 60 / 13 / 1 A]
*ENG
[De 0 a 60 / 12 / 1 A]
*ENG
[De 0 a 60 / 13 / 1 A]
Ajusta la corriente para la banda de transferencia de imagen para Cian en el modo a todo
color para papel grueso 1.
Transferencia de imgenes: Velocidad
baja:Y
*ENG
[De 0 a 60 / 14 / 1 A]
359
Ajusta la corriente para el rodillo de transferencia de papel para el papel normal en el modo
de blanco y negro.
Normal: 120 mm/s, Baja: 60 mm/s
*ENG
[De 0 a 200 / 20 / 1 A /
incremento]
*ENG
[De 0 a 200 / 23 / 1 A /
incremento]
*ENG
*ENG
[De 0 a 200 / 12 / 1 A /
incremento]
Ajusta la corriente para el rodillo de transferencia de papel para el papel normal en el modo
de a todo color.
Normal: 120 mm/s, Baja: 60 mm/s
*ENG
[De 0 a 200 / 25 / 1 A /
incremento]
*ENG
[De 0 a 200 / 28 / 1 A /
incremento]
*ENG
[De 0 a 200 / 13 / 1 A /
incremento]
*ENG
[De 0 a 200 / 14 / 1 A /
incremento]
[T normal:Corregir tamao:B/N]
2411
360
Tablas SP principales-2
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
361
*ENG
*ENG
*ENG
5
015 Transferencia de papel: Baja: 1: S4
362
*ENG
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-2
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
363
*ENG
*ENG
*ENG
5
012 Transferencia de papel: Baja: 2: S3
016
364
*ENG
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-2
*ENG
*ENG
*ENG
*ENG
Ajusta la corriente para el rodillo de transferencia de papel para el papel fino en el modo
en blanco y negro.
Normal: 120 mm/s, Baja: 60 mm/s
*ENG
[De 0 a 200 / 20 / 1 A /
incremento]
*ENG
[De 0 a 250 / 12 / 1 A /
incremento]
Ajusta la corriente para el rodillo de transferencia de papel para el papel fino en el modo
a todo color.
Normal: 120 mm/s, Baja: 60 mm/s
*ENG
[De 0 a 200 / 25 / 1 A /
incremento]
365
2482
*ENG
[De 0 a 200 / 13 / 1 A /
incremento]
*ENG
001 Ajusta la corriente de transferencia del rodillo de transferencia de papel para la 1 cara del
papel brillante en modo blanco y negro.
2483
*ENG
001 Ajusta la corriente de transferencia del rodillo de transferencia de papel para la 1 cara del
papel brillante en modo a todo color.
[Grueso 1: Polarizacin: BN]
2502
*ENG
*ENG
No se utiliza
366
*ENG
[De 0 a 200 / 15 / 1 A /
incremento]
*ENG
No se utiliza
Tablas SP principales-2
[T grueso:Corregir tamao:B/N]
2511
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
No se utiliza
[De 100 a 4000 / 150 / 5%/
incremento]
250 mm > Tamao S3 > 194 mm
(Anchura del papel)
No se utiliza
[De 100 a 4000 / 275 / 5%/
incremento]
194 mm > Tamao S4> 150 mm
(Anchura del papel)
No se utiliza
[De 100 a 4000 / 400 / 5%/
incremento]
150 mm > Tamao S5 (Anchura del
papel)
No se utiliza
367
368
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-2
*ENG
*ENG
No se utiliza
*ENG
*ENG
No se utiliza
001
Ajusta la corriente para el rodillo de transferencia de papel para OHP en el modo en blanco
y negro.
Transferencia del
papel
*ENG
001
2630
Ajusta la corriente para el rodillo de transferencia de papel para OHP en el modo a todo
color.
Transferencia del
papel
*ENG
002
*ENG
003
*ENG
369
*ENG
*ENG
No se utiliza
*ENG
*ENG
No se utiliza
*ENG
*ENG
*ENG
[De 0 a 200 / 11 / 1 - A/
incremento]
*ENG
[De 0 a 200 / 13 / 1 - A/
incremento]
[De 0 a 200 / 20 / 1 - A/
incremento]
370
*ENG
[De 0 a 200 / 25 / 1 - A/
incremento]
Tablas SP principales-2
*ENG
[De 0 a 200 / 28 / 1 - A/
incremento]
*ENG
[De 0 a 200 / 11 / 1 - A/
incremento]
*ENG
[De 0 a 200 / 14 / 1 - A/
incremento]
*ENG
*ENG
*ENG
[De 0 a 200 / 11 / 1 A /
incremento]
*ENG
[De 0 a 200 / 13 / 1 A /
incremento]
[De 0 a 200 / 20 / 1 A /
incremento]
*ENG
[De 0 a 200 / 25 / 1 A /
incremento]
*ENG
[De 0 a 200 / 28 / 1 A /
incremento]
*ENG
[De 0 a 200 / 11 / 1 A /
incremento]
*ENG
[De 0 a 200 / 14 / 1 A /
incremento]
371
[SP1,2,3-T:Corregir tamao:B/N]
2761
*ENG
*ENG
*ENG
*ENG
001
005
009
372
*ENG
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-2
010
013
014
017
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
373
018
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
001
005
006
374
*ENG
*ENG
Tablas SP principales-2
009
010
013
014
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
375
017
5
018
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
376
*ENG
[De 0 a 200 / 15 / 1 A /
incremento]
Tablas SP principales-2
*ENG
[De 0 a 200 / 15 / 1 A /
incremento]
[SP4,5,6-T:Corregir tamao:B/N]
2791
*ENG
*ENG
*ENG
*ENG
*ENG
377
*ENG
*ENG
*ENG
*ENG
*ENG
378
*ENG
*ENG
[De 0 a 200 / 20 / 1 A /
incremento]
Tablas SP principales-2
*ENG
[De 0 a 200 / 11 / 1 A /
incremento]
*ENG
[De 0 a 200 / 13 / 1 A /
incremento]
*ENG
[De 0 a 200 / 25 / 1 A /
incremento]
*ENG
[De 0 a 200 / 28 / 1 A /
incremento]
*ENG
[De 0 a 200 / 11 / 1 A /
incremento]
*ENG
[De 0 a 200 / 14 / 1 A /
incremento]
*ENG
[De 0 a 200 / 15 / 1 A /
incremento]
*ENG
[De 0 a 200 / 15 / 1 A /
incremento]
379
*ENG
*ENG
*ENG
[De 0 a 200 / 11 / 1 A /
incremento]
*ENG
[De 0 a 200 / 13 / 1 A /
incremento]
[De 0 a 200 / 20 / 1 A /
incremento]
*ENG
[De 0 a 200 / 25 / 1 A /
incremento]
*ENG
[De 0 a 200 / 28 / 1 A /
incremento]
*ENG
[De 0 a 200 / 11 / 1 A /
incremento]
*ENG
[De 0 a 200 / 14 / 1 A /
incremento]
380
*ENG
[De 0 a 200 / 15 / 1 A /
incremento]
Tablas SP principales-2
2940
[De 0 a 200 / 15 / 1 A /
incremento]
002
*ENG
*ENG
*ENG
[Efecto secundario]:
Se aaden "580 ms" al tiempo de primera copia/impresin al utilizar el modo de velocidad
baja.
381
Tablas SP principales-3
SP3-XXX (Proceso)
3011
Se muestran todos los colores. Los resultados se muestran en el orden "Y C M K"
Por ejemplo, 11 (Y) 99 (C) 11 (M) 11 (K): La comprobacin automtica para el cian ha
fallado pero para los dems es correcta.
Consulte "Tablas de condicin de error" en la seccin de errores de control de proceso para
obtener ms detalles.
382
Tablas SP principales-3
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3013
003 Ejecucin: Bk
004 Ejecucin: C
005 Ejecucin: M
006 Ejecucin: Y
3014
383
*ENG
1: xito
De 2 a 9: Fallo
003 Ejecucin: Bk
004 Ejecucin: C
005 Ejecucin: M
006 Ejecucin: Y
3016
*ENG
*ENG
*ENG
*ENG
3020
001005
[De 0 a 30 / 4 / 1 s/incremento]
*ENG
Tablas SP principales-3
*ENG
*ENG
[De 0 a 99 / 20 / 1 vez/incremento]
*ENG
*ENG
[De 0 a 99 / 10 / 1 vez/incremento]
*ENG
*ENG
*ENG
*ENG
*ENG
[De 0 a 99 / 0 / 1 vez/incremento]
*ENG
*ENG
*ENG
Especifica el tiempo de agitacin del revelador para cada color en la inicializacin del
revelador.
*ENG
*ENG
*ENG
*ENG
005008
*ENG
[0 o 1 / 0 / 1 /en incrementos de 1]
*ENG
*ENG
*ENG
385
*ENG
3022
*ENG
[0 o 1 / 0 / 1 /en incrementos de 1]
*ENG
*ENG
*ENG
3041
001
Control de polarizacin
*ENG
Control de potencia LD
*ENG
[0 o 1 / 0 / 1/incremento] Alfanumrico
*ENG
0: Permitir
1: Prohibir
386
Tablas SP principales-3
[De 0 a 2 / 2 / 1/incremento]
Control de proceso de
004 ACC previo
*ENG
0: No ejecutado
1: Control de proceso
2: Control de TC
*ENG
0: FIJO
1: INICIALIZADO
2: CALCULADO
3044
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
1: PID (Vtref_Fixed)
2: PID (Vtref_Control)
004 S
*ENG
3: MBD (Vtref_Fixed)
4: MBD (Vtref_Control)
3045
001 ON/OFF
*ENG
[0 o 1 / 0 / 1 /en incrementos de 1]
0: Detectar, 1: No Detectar
[0 o 1 / 0 / 1 /en incrementos de 1]
002 Deteccin NE
*ENG
3101
387
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
009-012
Muestra la cantidad restante de tner de cada color. Se calculan mediante los tiempos de
funcionamiento de las bombas de suministro de tner.
*ENG
*ENG
*ENG
*ENG
Ajusta los umbrales de tner casi agotado para cada color. El mensaje de tner casi
agotado aparece en la pantalla LCD cuando la cantidad de tner restante alcanza este
013-016
umbral. Cuando uno de estos SP (SP3-101-009 a 012 o -032 a -035) alcanza este
umbral, se detecta el tner casi agotado.
013 Umbral de casi agotado: Bk
*ENG
*ENG
*ENG
*ENG
Umbral de Vt Delta
*ENG
388
Tablas SP principales-3
022-025
Muestra el valor de Vt delta total (Vt-Vtref) para cada color. Estos se calculan mediante el
recuento de pxeles.
*ENG
*ENG
*ENG
*ENG
*ENG
028-031
[0 a 255 / 10 / 1 V/incremento]
Muestra la cantidad de tner consumida calculada con el recuento de pxeles para cada
color.
*ENG
*ENG
*ENG
*ENG
5
[De 0 a 3000 / 0 / 0,001 g/incremento]
032-035 Muestra la cantidad de tner restante para cada color, utilizando el recuento de pxeles.
032 Pxel: Restante : Bk
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
389
045
NE BF de umbral de suma de
Vt delta
*ENG
046
Tiempo de desconexin de
mohno: Bk
*ENG
047
Tiempo de desconexin de
mohno: C
*ENG
Tiempo de desconexin de
048
mohno: M
*ENG
Tiempo de desconexin de
mohno: Y
*ENG
049
050-053 Ajusta el umbral del tner restante para la deteccin del tner casi agotado. DFU
3131
*ENG
*ENG
*ENG
*ENG
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 S
*ENG
3201
390
[De 0 a 99 / 0 / 1 vez/incremento]
Tablas SP principales-3
001 Actual: Bk
*ENG
002 Actual: C
*ENG
003 Actual: M
*ENG
004 Actual: Y
*ENG
3221
[Vtcnt: Presentacin/Configuracin]
Muestra o ajusta el valor actual de Vtcnt para cada color.
001 Actual: Bk
*ENG
002 Actual: C
*ENG
003 Actual: M
*ENG
004 Actual: Y
*ENG
005008
*ENG
006 Inicial: C
*ENG
007 Inicial: M
*ENG
008 Inicial: Y
*ENG
002 Actual: C
*ENG
003 Actual: M
*ENG
004 Actual: Y
*ENG
008
[Vtcnt: Presentacin/Configuracin]
001 Actual: Bk
005-
Muestra o ajusta el valor de Vtcnt para cada color en la inicializacin del revelador.
005 Inicial: Bk
3222
Muestra o ajusta el valor de Vtref para cada color en la inicializacin del revelador.
391
005 Inicial: Bk
*ENG
006 Inicial: C
*ENG
007 Inicial: M
*ENG
008 Inicial: Y
*ENG
009012
Muestra o ajusta la correccin de Vtref por cobertura de pxel para cada color.
*ENG
*ENG
*ENG
*ENG
3223
001 Inferior: Bk
*ENG
002 Inferior: C
*ENG
003 Inferior: M
*ENG
004 Inferior: Y
*ENG
005 Superior: Bk
*ENG
006 Superior: C
*ENG
007 Superior: M
*ENG
008 Superior: Y
*ENG
009 TC inicial
*ENG
010 Superior: TC
*ENG
392
Tablas SP principales-3
011 Inferior: TC
*ENG
*ENG
*ENG
*ENG
*ENG
016 TC superior:K
*ENG
017 TC superior: C
*ENG
018 TC superior: M
*ENG
019 TC superior: Y
*ENG
3224
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
393
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3236
[De 0 a 20 / 3 / 0,1%/incremento]
Ajusta el umbral de la cobertura alta.
[De 0 a 100 / 60 / 1%/incremento]
[De 0 a 5 / 0,5 / 0,1 wt%/incremento]
001 ltimo: Bk
*ENG
002 ltimo: C
*ENG
003 ltimo: M
*ENG
004 ltimo: Y
*ENG
3237
394
Tablas SP principales-3
3238
*ENG
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 S
*ENG
3241
001 Coeficiente: Bk
*ENG
002 Coeficiente: C
*ENG
003 Coeficiente: M
*ENG
004 Coeficiente: Y
*ENG
005 Correccin: Bk
*ENG
006 Correccin: C
*ENG
007 Correccin: M
*ENG
*ENG
008 Correccin: Y
3251
[Cobertura]
Estos (-001 hasta -016) son coeficientes para el SP3-222-009 al -012.
001 ltimo: Bk pxel
*ENG
*ENG
*ENG
*ENG
395
*ENG
006 S Media: C
*ENG
007 S Media: M
*ENG
008 S Media: Y
*ENG
009 M media: Bk
*ENG
010 M Media: C
*ENG
011 M media: M
*ENG
012 M Media: Y
*ENG
*ENG
014 L Media: C
*ENG
015 L Media: M
*ENG
016 L Media: Y
*ENG
*ENG
018
*ENG
019
*ENG
Tablas SP principales-3
020
*ENG
021
*ENG
022
*ENG
*ENG
*ENG
*ENG
*ENG
028
3311
*ENG
*ENG
*ENG
*ENG
*ENG
005-007 Muestra la tensin de correccin del sensor ID (difusin) para los ajustes de Vsg.
005 Voffset dif: C
*ENG
*ENG
*ENG
008-010 Muestra el voltaje de correccin del sensor ID para los ajustes de Vsg.
397
3321
*ENG
*ENG
*ENG
3322
398
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3323
001 Ifsg: Bk
*ENG
002 Ifsg: C
*ENG
003 Ifsg: M
*ENG
004 Ifsg: Y
*ENG
Tablas SP principales-3
*ENG
*ENG
*ENG
3324
*ENG
*ENG
*ENG
*ENG
001 Ms reciente
*ENG
002 Reciente 1
*ENG
003 Reciente 2
*ENG
004 Reciente 3
*ENG
005 Reciente 4
*ENG
006 Reciente 5
*ENG
007 Reciente 6
*ENG
008 Reciente 7
*ENG
009 Reciente 8
*ENG
010 Reciente 9
*ENG
3363
399
*ENG
Tiempo de retraso de la
002
deteccin
*ENG
*ENG
*ENG
3411
001 ltimo: Bk
*ENG
002 ltimo: C
*ENG
003 ltimo: M
*ENG
004 ltimo: Y
*ENG
3421
400
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-3
*ENG
*ENG
*ENG
*ENG
3501
*ENG
*ENG
*ENG
*ENG
3510
*ENG
*ENG
003 Encendido: BN
*ENG
*ENG
005 MUSIC: BN
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3511
401
001
*ENG
002
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
006
*ENG
*ENG
Correccin de tiempo de
021
inactividad: Activada/Desactivada
*ENG
*ENG
*ENG
[De 0 a 1 / 1 / 0,01/incremento]
*ENG
*ENG
[De 0 a 1 / 1 / 0,01/incremento]
019
402
[0 o 1 / 1 / 1 /en incrementos de 1]
0: Sin correcin (Desactivada),
1: Correccin (Activada)
026
*ENG
027
*ENG
[De 0 a 1 / 1 / 0,01/incremento]
Tablas SP principales-3
028
*ENG
029
*ENG
[De 0 a 1 / 1 / 0,01/incremento]
030
*ENG
[De 0 a 99 / 2 / 1/incremento]
031
*ENG
*ENG
*ENG
001 Ao
*ENG
[De 0 a 99 / 0 / 1/incremento]
002 Mes
*ENG
[De 1 a 12 / 1 / 1/incremento]
003 Fecha
*ENG
[De 1 a 31 / 1 / 1/incremento]
004 Hora
*ENG
[De 0 a 23 / 0 / 1/incremento]
005 Minuto
*ENG
[De 0 a 59 / 0 / 1/incremento]
001 Temperatura
*ENG
*ENG
403
*ENG
*ENG
*ENG
*ENG
*ENG
[Modo Actualizacin]
3516
404
Mientras se realizan impresiones con cobertura baja, el revelador se agita con menos
consumo de tner y la atraccin de transporte de tner tiende a aumentar. Esto puede causar
una baja densidad de imagen o una transferencia deficiente (puntos blancos). Para prevenir
esto, se debe consumir el tner coagulado o sobrecargado mediante el modo de
actualizacin.
*ENG
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-3
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
025
*ENG
026
Coeficiente de Vb de finalizacin de
trabajo
*ENG
*ENG
405
028
*ENG
*ENG
*ENG
*ENG
406
Ajusta el umbral de temperatura para prevenir que se dae la hoja de limpieza en la unidad
de limpieza de la banda de transferencia. Si la temperatura supera este valor, el tner se
aplica a la banda de transferencia a los intervalos definidos durante el trabajo para evitar
que la hoja se voltee.
*ENG
*ENG
*ENG
*ENG
[0 o 1 / 0 / 1 /en incrementos de 1]
*ENG
0: OFF. 1: ON
*ENG
*ENG
*ENG
008 MUSIC
*ENG
*ENG
*ENG
*ENG
[De 0 a 2 / 0 / 1/incremento]
0: OFF. 1: ON (una vez), 2: ON (dos veces)
[De 0 a 2 / 0 / 1/incremento]
0: OFF. 1: ON (una vez), 2: ON (dos veces)
[0 o 1 / 0 / 1 /en incrementos de 1]
0: OFF. 1: ON
Tablas SP principales-3
[0 o 1 / 0 / 1 /en incrementos de 1]
*ENG
3519
*ENG
[0 o 1 / 1 / 1 /incremento]
002 MUSIC
*ENG
*ENG
003 Ajuste de TC
3520
*ENG
*ENG
*ENG
[0 o 3 / 0 / 1 revolucin/incremento]
*ENG
005 a Ajusta la temperatura de umbral para introducir la rotacin inactiva de la ITB despus del
011 control del proceso.
005 Umbral rango temp.:T2
*ENG
[20 o 30 / 30 / 1 grado/incremento]
*ENG
[0 o 15 / 15 / 1 grado/incremento]
*ENG
[0 o 50 / 30 / 1 grado/incremento]
*ENG
[0 o 50 / 15 / 1 grado/incremento]
407
*ENG
[0 a 99 / 10 / en incrementos de 1C]
*ENG
[De 0 a 99 / 50 / 1% HR/incremento]
*ENG
[De 0 a 99 / 6 / 1 g/m3/incremento]
002
[Temporizador rpido]
100 Configuracin de hora
*ENG
001
*ENG
*ENG
[0 a 99 / 10 / en incrementos de 1C]
*ENG
[De 0 a 99 / 50 / 1% HR/incremento]
004
Cambio de humedad
absoluta
*ENG
[De 0 a 99 / 6 / 1 g/m3/incremento]
005
Nmero mximo de
ejecuciones
*ENG
3611
408
[De 0 a 99 / 10 / 1 vez/incremento]
Tablas SP principales-3
*ENG
002 C (Actual)
*ENG
003 M (Actual)
*ENG
004 Y (Actual)
*ENG
*ENG
*ENG
*ENG
*ENG
009
Bk (Configuracin objetivo
estndar)
*ENG
010
C (Configuracin objetivo
estndar)
*ENG
011
M (Configuracin objetivo
estndar)
*ENG
012
Y (Configuracin objetivo
estndar)
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
409
018
K (Humedad absoluta
mxima)
*ENG
019
C (Humedad absoluta
mxima)
*ENG
M (Humedad absoluta
020
mxima)
*ENG
021
3612
Y (Humedad absoluta
mxima)
[De 1 a 99 / 15 / 1 g/m3/incremento]
*ENG
[Presentacin de Vk]
Muestra Vk para cada color.
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 S
*ENG
[Gamma de revelado:Presentacin]
3621
410
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-3
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
411
412
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3711
001 Vcnt
*ENG
002 Vt
*ENG
003 Sensibilidad: HL
*ENG
004 Sensibilidad: HM
*ENG
005 Sensibilidad: ML
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
011 Ajuste: Vt
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-3
3712
*ENG
[De 0 a 9 / 9 / 1/incremento]
[Control de HST: C]
Muestra los ajustes de fbrica para la PCU de Magenta.
001 Vcnt
*ENG
002 Vt
*ENG
003 Sensibilidad: HL
*ENG
004 Sensibilidad: HM
*ENG
005 Sensibilidad: ML
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
011 Ajuste: Vt
*ENG
*ENG
*ENG
*ENG
*ENG
[De 0 a 9 / 9 / 1/incremento]
3713
[Control de HST: M]
Muestra los ajustes de fbrica para la PCU de cian.
001 Vcnt
*ENG
002 Vt
*ENG
003 Sensibilidad: HL
*ENG
004 Sensibilidad: HM
*ENG
413
005 Sensibilidad: ML
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
011 Ajuste: Vt
*ENG
*ENG
*ENG
*ENG
*ENG
[De 0 a 9 / 9 / 1/incremento]
3714
414
[Control de HST:Y]
Muestra los ajustes de fbrica de la PCU de amarillo.
001 Vcnt
*ENG
002 Vt
*ENG
003 Sensibilidad: HL
*ENG
004 Sensibilidad: HM
*ENG
005 Sensibilidad: ML
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
Tablas SP principales-3
011 Ajuste: Vt
*ENG
*ENG
*ENG
*ENG
*ENG
[De 0 a 9 / 9 / 1/incremento]
3800
*CTL
[De 0 a 4 / 0 / 1/incremento]
*CTL
003
*CTL
004
*CTL
No se utiliza
[De 0 a 50 / - / 1/incremento]
No se utiliza
[De 0 a 2000 / 0 / 1 hoja/incremento]
No se utiliza
[De 0 a 200000 / - / 1 cm2/incremento]
No se utiliza
005
*CTL
008
DFU
*ENG
Ajusta la cantidad de tner entre casi lleno y lleno. (0,1 indica 10%.)
415
*ENG
[0 o 1 / 1 /-]
0: Activar llamada a @Remote
1: Desactivar llamada a @Remote
011
NOTA:
Si se ha sustituido la botella de recogida de tner de la PCDU antes de que la mquina
detectase que el tner usado est casi lleno cuando este ajuste est configurado en "0", la
mquina no puede detectar que la botella de recogida de tner est casi llena. En este caso,
configure SP3-902-017 en "1".
Umbral da:Casi lleno
*ENG
[De 1 a 30 / 10 / 1 da/incremento]
012 Configura el umbral de das para la presentacin de casi lleno. El aviso de botella de
recogida de tner casi llena de la PCDU se muestra despus de que el sensor de recogida
de tner llena haya detectado el actuador en la botella de recogida de tner de la PCDU.
*ENG
[0 a 999999999/1/1]
014 Fecha de deteccin de lleno
3810
*ENG
*CTL
[De 0 a 4 / 0 / 1/incremento]
416
*CTL
003
*CTL
004
*CTL
No se utiliza
[De 0 a 50 / - / 1/incremento]
No se utiliza
[De 0 a 2000 / 0 / 1 hoja/incremento]
No se utiliza
[De 0 a 200000 / - / 1 cm2/incremento]
Tablas SP principales-3
No se utiliza
005
*CTL
008
DFU
*ENG
Ajusta la cantidad de tner entre casi lleno y lleno. (0,1 indica 10%.)
Activa o desactiva la llamada a @Remote.
Ajuste de la alarma
*ENG
[0 o 1 / 1 /-]
0: Activar llamada a @Remote
1: Desactivar llamada a @Remote
011
NOTA:
Si se ha sustituido la botella de recogida de tner antes de que la mquina detectase que
el tner usado est casi lleno cuando este ajuste est configurado en "0", la mquina no
puede detectar que la botella de recogida de tner est casi llena. En este caso, configure
SP3-902-017 en "1".
Umbral da:Casi lleno
*ENG
[De 1 a 30 / 10 / 1 da/incremento]
012 Configura el umbral de das para la presentacin de casi lleno. El aviso de botella de
recogida de tner casi llena de la IT se muestra despus de que el sensor de recogida de
tner llena haya detectado el accionador en la botella de recogida de tner de la ITB.
*ENG
3901
001
*ENG
*ENG
[0 o 1 / 1 /-]
0: Desactivado, 1: Activado
417
Activa o desactiva el indicador de deteccin de la unidad nueva para cada unidad de PM.
El uso de estos contadores se explica en la seccin de mantenimiento preventivo y en las
partes correspondientes de la seccin 3 (Sustitucin y ajuste).
*ENG
*ENG
[0 o 1 / 0 /-]
*ENG
0: Desactivado, 1: Activado
*ENG
005 Revelador: Bk
*ENG
006 Revelador: C
*ENG
007 Revelador: M
*ENG
008 Revelador: Y
*ENG
009 PCU: Bk
*ENG
010 PCU: C
*ENG
[0 o 1 / 0 /-]
011 PCU: M
*ENG
0: Desactivado, 1: Activado
012 PCU: Y
*ENG
*ENG
*ENG
0: Desactivado, 1: Activado
*ENG
*ENG
*ENG
418
[0 o 1 / 0 /-]
0: Desactivado, 1: Activado
[0 o 1 / 0 /-]
*ENG
*ENG
*ENG
019
No se utiliza
[0 o 1 / 0 /-]
0: Desactivado, 1: Activado
Tablas de SP principales-4
Tablas de SP principales-4
SP4-XXX (Escner)
4008
001
*ENG
*ENG
001
*ENG
Establece el margen en blanco en cada lado para borrar la sombra en el original provocada
por la separacin entre el original y la escala.
*ENG
*ENG
Ejecuta el giro libre del escner con la lmpara de exposicin encendida o apagada en el
siguiente modo.
Modo a todo color / Tamao 1:1 / A3 o DLT
4014
*ENG
[0 o 1 / 0 /-]
0: Desactivado, 1: Activado
[Escaneo]
Ejecuta el giro libre del escner con cada modo.
001
002
Deshabilitar deteccin de
posicin inicial
4020
001
[Comprobacin de polvo]
Deteccin: ACTIVADO/
DESACTIVADO
*ENG
*ENG
[De 0 a 8 / 4 / 1/incremento]
0: nivel de deteccin ms bajo
8: nivel de deteccin ms alto
Selecciona el nivel de correccin de lnea de
escaneo secundaria cuando se utiliza el ARDF.
[De 0 a 4 / 0 / 1/incremento]
*ENG
0: Desactivado
1: Ms dbil
2: Dbil
3: Fuerte
4: Ms fuerte
420
Tablas de SP principales-4
001
Visualiza un cdigo que representa el tamao del original detectado por los sensores de
original. (Consulte la "Tabla de comprobacin de entrada".)
Comprobacin de
funcionamiento de APS
Especifica el resultado de la deteccin cuando las salidas de los sensores de originales estn
todos DESACTIVADOS.
[De 0 a 0 / 2 / 1/incremento]
*ENG
0: Sin original
1: A5-Longitudinalmente (16K SEF si 4305 est
configurado en 3)
[De 0 a 3 / 0 / 1/incremento]
4305
8K/16K Detection
(Deteccin de 8K/16K)
*ENG
001 Este programa habilita la mquina para reconocer automticamente el tamao 8K/16K.
4308
4309
*ENG
[0 o 1 / 0 / 1 /incremento]
0: ACTIVADO, 1: DESACTIVADO
*ENG
*ENG
*ENG
003
Lmpara encendida:Tiempo de
retardo
421
*ENG
4417
422
[De 0 a 24 / 0 / 1/incremento]
13: Trama de cuadrcula CMYK
14: Parche de color CMYK
15: Trama de grises (1)
16: Trama de grises (2)
17: Trama de grises (3)
18: Trama de sombreado
19: Trama de lneas finas
20: Trama escaneada + cuadrcula
21: Escala escaneada + grises
22: Trama escaneada + parche de color
23: Trama escaneada + inclinada C
24: Trama escaneada + inclinada D
Tablas de SP principales-4
001 Copia
002 Escner
*ENG
[0 a 3 / 3 / 1 /incremento]
003 Fax
4440
[Ajuste de saturacin]
Ajusta el nivel de saturacin de copia.
[0 a 5 / 3 / 1 /en incrementos de 1]
0: Alto
1: El ms bajo
001 -
*ENG
2: Ms bajo
3: Predeterminado
4: Ms alto
5: El ms alto
4450
ACTIVAR/DESACTIVAR
001 reduccin de negro
[0 o 1 / 1 / - ] 0: OFF, 1: ON
ACTIVAR/DESACTIVAR SH
4460
Especifica el nivel de borrado del fondo en el modo ADS. Puede ajustar su nivel para cada
mtodo de escaneado (cristal de exposicin, ADF).
*ENG
*ENG
4501
423
*ENG
002 Copia:C:texto
*ENG
003 Copia:M:texto
*ENG
004 Copia:Y:texto
*ENG
[De 0 a 10 / 5 / 1/incremento]
*ENG
006 Copia:C:foto
*ENG
*ENG
008 Copia:Y:foto
*ENG
4505
Ajusta la correccin offset para las zonas claras del patrn ACC.
*ENG
002 Mster:C
*ENG
003 Mster:M
*ENG
004 Mster: Y
*ENG
005 Secundario:K
*ENG
006 Secundario: C
*ENG
007 Secundario: M
*ENG
008 Secundario: Y
*ENG
4506
424
[Correccin ACC:Brillo]
Reservado
*ENG
002 Mster:C
*ENG
003 Mster:M
*ENG
004 Mster: Y
*ENG
Tablas de SP principales-4
005 Secundario:K
*ENG
006 Secundario: C
*ENG
007 Secundario: M
*ENG
008 Secundario: Y
*ENG
4550
[Apl. escner:Texto/Grfico]
4551
4552
4553
[Apl. escner:Texto/Foto]
4554
4565
4570
4571
4572
-005
Reservado
*ENG
[De 0 a 15 / 8 / 1/incremento]
0: MTF desconectado
*ENG
[De 0 a 7 / 4 / 1/incremento]
-006 Utilcelo para eliminar los "saltos" en caso de que aparezcan. Ajuste un valor superior para
una imagen ms suave.
Brightness:1-255 (Brillo: 1-255)
-007
*ENG
Configure un valor ms alto para obtener un resultado ms oscuro; un valor ms bajo para
un resultado ms claro.
425
Contraste: 1-255
-008
*ENG
Configure un valor ms alto para obtener ms contraste; un valor ms bajo para menos
contraste.
Borrar punto irregular :0 (x1) 1-7 (Fuerte)
*ENG
[De 0 a 7 / 0 / 1/
incremento]
-009 Ajusta el nivel de borrado de puntos irregulares. Ajuste un nivel superior para un efecto ms
fuerte e inferior para un efecto ms dbil.
0: No activado
4580
4582
4583
-005
*ENG
[De 0 a 15 / 8 / 1/incremento]
0: MTF desconectado
*ENG
[De 0 a 7 / 4 / 1/incremento]
-006 Utilcelo para eliminar los "saltos" en caso de que aparezcan. Ajuste un valor superior para
una imagen ms suave.
Brightness:1-255 (Brillo: 1-255)
-007
426
Configure un valor ms alto para obtener un resultado ms oscuro; un valor ms bajo para
un resultado ms claro.
Contraste: 1-255
-008
*ENG
*ENG
Configure un valor ms alto para obtener ms contraste; un valor ms bajo para menos
contraste.
Tablas de SP principales-4
*ENG
[De 0 a 7 / 0 / 1/incremento]
Selecciona el nivel de contraste para el modo de texto B/N Ajusta el nivel de borrado de
-009 puntos irregulares. Ajuste un nivel superior para un efecto ms fuerte e inferior para un efecto
ms dbil.
0: No activado
Borrar textura:0 (Fijo), 1-2
*ENG
[De 0 a 2 / 0 / 1 /incremento]
Ajusta el nivel de borrado de las texturas. Ajuste un nivel superior para un efecto ms fuerte
-010 e inferior para un efecto ms dbil. Este SP (sufijo "-010") slo existe en SP4580, 4582 y
4583.
0: No activado
4581
4584
4585
*ENG
[De 0 a 15 / 8 / 1/
incremento]
0: MTF desconectado
-005
*ENG
[De 0 a 7 / 4 / 1/incremento]
-006 Utilcelo para eliminar los "saltos" en caso de que aparezcan. Ajuste un valor superior para
una imagen ms suave.
-007
Brightness:1-255 (Brillo:
1-255)
*ENG
Configure un valor ms alto para obtener un resultado ms oscuro; un valor ms bajo para
un resultado ms claro.
Contraste: 1-255
*ENG
-008 Configure un valor ms alto para obtener ms contraste; un valor ms bajo para menos
contraste.
427
*ENG
[De 0 a 7 / 0 / 1/
incremento]
-009 Selecciona el nivel de contraste para el modo de texto B/N Ajusta el nivel de borrado de
puntos irregulares. Ajuste un nivel superior para un efecto ms fuerte e inferior para un efecto
ms dbil.
0: No activado
4647
001 Encendido
001 4802
*ENG
002
4804
Lamp ON (Lmpara
encendida)
428
001 4806
[Movimiento de carro]
Tablas de SP principales-4
4807
Este SP genera la lectura de los datos finales al final de una ejecucin de ACC.
Se devuelve un cero en caso de que se produzca un error en la lectura de datos.
[De 0 a 255 / 0 / 1 /incremento]
001 R DATA1
*ENG
002 G DATA1
*ENG
003 B DATA1
*ENG
004 R DATA2
*ENG
005 G DATA2
*ENG
006 B DATA2
*ENG
4904
429
001
Prueba2
Realiza una comprobacin del trayecto de la imagen en la placa BCU y muestra el resultado.
4918
009 -
4993
[Correccin de brillo]
Selecciona el nivel de correccin de brillo.
*ENG
[De 0 a 9 / 4 / 1/incremento]
0: sensibilidad ms dbil
9: sensibilidad ms fuerte
430
Tablas de SP principales-4
*ENG
[De 0 a 9 / 4 / 1/incremento]
0: correccin de inclinacin ms dbil,
9: correccin de inclinacin ms fuerte
4994
*ENG
0: Prioridad de texto
1: Normal
2: Prioridad de fotografa
001 -
*ENG
0: El ms claro
6: El ms oscuro
431
Tablas SP principales-5
SP5-XXX (Modo)
5024
*CTL
0: mm (Europa/Asia)
1: pulgadas (EE.UU.)
[Contador de contabilidad]
5045
*CTL
0: Revelados
1: Impresiones
5047
[Presentacin de papel]
Activa o desactiva la presentacin de papel impreso en el LCD.
5051
*CTL
[0 o 1 / 0 /-]
0: Desactivado, 1: Activado
5051 1 -
*CTL
0: ON
1: OFF
5055
432
Tablas SP principales-5
001 -
5056
*CTL
[0 o 1 / 0 /-]
0: No mostrar, 1: Mostrar
[0 o 1 / 0 /-]
0: No mostrar, 1: Mostrar
001 PCU: Bk
*CTL
002 PCU: M
*CTL
003 PCU: C
*CTL
004 PCU: Y
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
012
0: OFF 1: ON
001 -
5062
[0 o 1 / 0 /-]
001 -
5061
*CTL
[0 o 1 / 0 /-]
0: No mostrar, 1: Mostrar
*CTL
433
5066
001 -
*CTL
[0 o 1 / 0 /-]
0: No mostrar, 1: Mostrar
001 PCU: Bk
*CTL
002 PCU: M
*CTL
003 PCU: C
*CTL
004 PCU: Y
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
012
5104
434
*CTL
Tablas SP principales-5
[De 0 a 2 / 0 / 1/incremento]
PCU: Bk
*CTL
001
0: No
1: S
2: S, excepto bypass
Especifica si el contador se duplica para papel A3/DLT. "Yes" (S) contabiliza salvo desde
la bandeja bypass. Cuando se selecciona "Yes" (S), el papel A3 y DLT se cuenta dos veces,
es decir, A4 x2 y LT x2 respectivamente.
5113
001
*CTL
*CTL
0: Ninguno
1: Dispositivo de ampliacin 1
2: Dispositivo de ampliacin 2
3: Dispositivo de ampliacin 3
5114
001
5118
*CTL
[Desactivar copiado]
*CTL
5120
001
*CTL
5121
001
[Temporizacin de contador
ascendente]
*CTL
5126
*ENG
5127
[Modo APS]
*CTL
*CTL
5162
*CTL
436
[0 o 1 / 0 /-]
0: Impresin automtica
1: Sin impresin automtica
Tablas SP principales-5
Si va a cambiar los bit switches de impresora, debe iniciar sesin en el modo de servicio
con este SP antes de entrar en el modo SP de impresora.
[0 o 1 / 0 /-]
001 -
*CTL
0: Desactivado
1: Activado
5181
[Ajuste de tamao]
Ajusta el tamao de papel para cada bandeja.
001 Bandeja 1: 1
*ENG
002 Bandeja 1: 2
*ENG
003 Bandeja 1: 3
*ENG
004 Bandeja 1: 4
*ENG
005 Bandeja 2: 1
*ENG
006 Bandeja 2: 2
*ENG
007 Bandeja 2: 3
*ENG
008 Bandeja 2: 4
*ENG
009 Bandeja 3: 1
*ENG
010 Bandeja 3: 2
*ENG
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A3, 1: DLT
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B4, 1: LG
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B5 LEF, 1: Exe LEF
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A4 LEF, 1: LT LEF
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A3, 1: DLT
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B4, 1: LG
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B5 LEF, 1: Exe LEF
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A4 LEF, 1: LT LEF
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A3, 1: DLT
437
011 Bandeja 3: 3
*ENG
012 Bandeja 3: 4
*ENG
013 Bandeja 4: 1
*ENG
014 Bandeja 4: 2
*ENG
015 Bandeja 4: 3
*ENG
016 Bandeja 4: 4
*ENG
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B4, 1: LG
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B5 LEF, 1: Exe LEF
[De 0 a 2 / 0 (EU/ASIA), 1 (NA) / - ]
0: A4LEF, 1: LTLEF
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A3, 1: DLT
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B4, 1: LG
[0 o 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B5 LEF, 1: Exe LEF
[Operacin desconectar RK 4]
5186
001 -
*ENG
0: Desactivar
1: Activar
5188
001 5196
*CTL
001 5212
438
[Numeracin de pgina]
No se utiliza
*CTL
Tablas SP principales-5
[Establecer hora]
Ajusta la configuracin de hora del reloj de tiempo real para la zona horaria local.
Ejemplos: Para Japn (+9 GMT), introduzca 540 (9 horas x 60 min.)
DOM: +540 (Tokio)
5302
EU :+ 60 (Pars)
CH :+480 (Pekn)
TW :+480 (Taipei)
AS :+480 (Hong Kong)
002 Diferencia horaria
5307
*CTL#
[Horario verano]
[De 0 a 1 / NA, EU, ASIA / 1 /incremento]
Ajuste
001
0: Desactivado
1: Activado
NA y EUR: 1, ASIA: 0
439
5404
5411
[Certificacin LDAP]
004 Certificacin fcil
440
*CTL
*CTL
Tablas SP principales-5
Contrasea nula no
permitida
*CTL
[1 a 1/0/0]
0: No se permite contrasea nula.
1: Contrasea nula permitida.
5413
[Ajuste de bloqueo]
001
Bloqueo activado/
desactivado
*CTL
*CTL
[1 a 10/5/1]
Determina si el sistema espera el tiempo
indicado para la introduccin de un ID de
usuario y contrasea correcto despus de que
se haya producido un bloqueo de cuenta.
003
Cancelacin activada/
desactivada
*CTL
[0 a 1/0/1]
0: Off (ningn tiempo de espera, el bloqueo no
se cancela)
1: On (el sistema espera, cancela el bloqueo si
se introduce el ID de usuario y la contrasea
correcta.
*CTL
005
5414
Hora de borrado de
contador
*CTL
No se utilizan.
[Mitigacin de acceso]
441
001
Mitigacin activada/
desactivada
Activa/desactiva la ocultacin de ID y
contraseas idnticas que se utilizan
continuamente.
*CTL
[0 a 1/0/1]
0: Desactivado
1: Activado
*CTL
5415
[Ataque de contrasea]
*CTL
*CTL
5416
[Informacin de acceso]
001
*CTL
002
Nmero mx. de
contraseas de acceso
*CTL
*CTL
442
Tablas SP principales-5
5417
[Ataque de acceso]
001
Nmero permisible de
accesos
*CTL
002
003
Espera de caida de
productividad
*CTL
*CTL
*CTL
[Autenticacin de usuario]
5420
001 Copia
*CTL
443
Configuracin de seguridad
de color
*CTL
Activa o desactiva la limitacin de la copia en color para cada modo de copia cuando la
autenticacin de usuario est configurada en "ON".
0: Activar (Valor predeterminado), 1: Desactivar
002 Bit 0: Modo BN
Bit 1: Modo monocolor
Bit 2: Modo bicolor
Bit 3: Modo a todo color
Bit 4: Modo de color automtico
Bit 5 a 7: Reservados
5
011 Document Server
*CTL
021 Fax
*CTL
031 Escner
*CTL
041 Impresora
*CTL
444
Tablas SP principales-5
051 SDK1
061 SDK2
[0 o 1 / 0 / 1] 0: Activado. 1: OFF
*CTL
071 SDK3
5481
*CTL
*CTL
[0 a 1/1/1]
1: Activado, 0: Desactivado
5490
*CTL
*CTL
[Alarma PM]
[De 0 a 9999 / 0 / 1/incremento]
001 Nivel de alarma PM
*CTL
0: Alarma desactivada
De 1 a 9999: La alarma se dispara cuando
Valor (1 a 9999) x 1000 > contador de PM
445
[0 o 1 / 1 /-]
002
5504
Alarma de recuento de
originales
*CTL
[Alarma de atasco]
*CTL
Configura la alarma de forma que suene para el nivel de atasco especificado (no se
incluyen los errores de alimentacin de papel).
[0 a 3 / 3 / 1 /incremento]
001 0: Cero (desactivado)
1: Bajo (2500 atascos)
5505
5507
*CTL
*CTL
Alarma de suministro de
papel
0: Desactivado, 1: Activado
002
Alarma de suministro de
grapas
0: Off, 1: On
446
Tablas SP principales-5
002*
003*
[Llamada CC]
Atasco persiste
*CTL
0: Deshabilitar, 1: Habilitar
0: Deshabilitar, 1: Habilitar
0: Deshabilitar, 1: Habilitar
[De 3 a 30 / 10 / 1 minuto/incremento]
011* Establece el tiempo que debe durar un atasco antes de que pase a ser un "atasco de papel
no atendido".
447
[De 2 a 10 / 5 / 1/incremento]
012* Configura cuntos atascos de papel continuos tienen que producirse para que se inicie
una llamada.
Puerta abierta:duracin
[De 3 a 30 / 10 / 1/incremento]
013* Configura el periodo de tiempo en el que la puerta permanece abierta antes de que la
mquina inicie una llamada.
[Ajuste de Alarma/SC]
Cuando se usa @Remote, estos cdigos SP se pueden configurar de forma que emitan
una llamada al SC cuando se produzca un error SC. Si este SP est desactivado, no se
emite la llamada al SC cuando se produce un error SC.
5515
001 Llamada SC
002
[0 o 1 / 1 /-]
0: Desactivado
1: Activado
[0 o 1 / 1 /-]
0: Desactivado
1: Activado
448
Tablas SP principales-5
005 Sobreescribe los valores actuales sobre los ajustes de fbrica de los puntos de control
gamma base.
006
5611
001
*ENG
002
B-M
*ENG
003
G-C
*ENG
004
G-Y
*ENG
005
R-M
*ENG
006
R-Y
*ENG
449
[0 o 1 / 1 /-]
001
*CTL
450
[Borrado de memoria]
001 Borrar todo
003 SCS
005 MCS
Tablas SP principales-5
Bandeja prioritaria
Proteccin de mens
Ajuste del sistema excepto por el ajuste del
Economizador de energa.
Configuracin de I/F (Buffer de E/S e Inactividad de
E/S)
Men PCL
011 NCS
012 R-FAX
017 CCS
451
019 LCS
021 ECS
5803
[Comprobacin de
entrada]
5804
[Comprobacin de salida]
5806
002 NO 0
003 RET.
004 EXE.ALL
005 EXE.K
006 EXE.M
007 EXE.C
008 EXE.Y
[Reinicio de SC]
Reinicia una condicin de llamada de servicio de tipo A.
5810
Gire el interruptor principal hasta la posicin de apagado y encendido despus de
reiniciar el cdigo SC.
001 Reiniciar fusor SC
5811
452
Tablas SP principales-5
002 Presentacin
*ENG
004 5812
*CTL
Establece el nmero de telfono para un representante del servicio tcnico. Este nmero
001 se imprime en la lista de contador, que se imprime con el men "Counter" (Contador) del
usuario.
Puede tener 20 caracteres como mximo (es posible escribir tanto nmeros como
caracteres alfanumricos).
Fax
*CTL
Establece el nmero de fax o telfono para un representante del servicio tcnico. Este
002 nmero se imprime en la lista "Counter" (Contador).
Puede tener 20 caracteres como mximo (es posible escribir tanto nmeros como
caracteres alfanumricos).
Consumibles
*CTL
*CTL
004 Utilcelo para introducir el nmero de telfono de su agencia de ventas. Escriba el nmero
y pulse #.
5816
[Servicio remoto]
*CTL
Configuracin de interfaz
Selecciona la configuracin de servicio remoto.
001
[0 a 2 / 2 / 1 /en incrementos de 1]
0: Servicio remoto desactivado
1: Servicio remoto CSS activado
2: Servicio @Remote activado
453
[0 o 1 / 0 / 1 /incremento]
0: Inicio del servicio
1: Fin del servicio
NOTA: Este SP slo se activa cuando SP 5816-001 est configurado en "2".
Indicador de funcin
Desactivar SSL
Utiliza o no utiliza la certificacin de RCG por SSL cuando se llama al RCG.
007 [De 0 a 0 / 2 / 1/incremento]
0: Utiliza la certificacin de RCG
1: No utiliza la certificacin de RCG
Fin de tiempo de espera de conexin de RCG
008 Especifica el intervalo de tiempo de espera de conexin cuando se llama al RCG.
[1 a 90 / 10 / en incrementos de 1 segundo]
Fin de tiempo de espera de escritura de RCG
009 Especifica el tiempo de espera de escritura cuando se llama al RCG.
[De 1 a 100 / 60 / 1 segundo /incremento]
Tiempo de espera de lectura de RCG
010 Especifica el tiempo de espera de lectura cuando se llama al RCG.
[De 1 a 100 / 60 / 1 segundo /incremento]
Activacin del puerto 80
011
454
Tablas SP principales-5
456
Tablas SP principales-5
067
11
12
13
14
15
16
17
18
457
CERT: Error
Muestra un cdigo numrico que describe el motivo de la peticin para actualizar la
certificacin.
0
Se ha emitido una notificacin de error SSL. Emitido una vez que la certificacin ha
vencido.
068
El ID de la peticin de la certificacin.
458
Tablas SP principales-5
150
151
152
153
154
Seleccin de pas
No se utiliza
Juicio automtico de tipo de lnea
No se utiliza
Resultado del juicio de tipo de lnea
No se utiliza
Seleccin de marcacin/presin
No se utiliza
Nmero saliente/lnea exterior
No se utiliza
459
156
157
161
162
163
164
Lmite de retransmisin
No se utiliza
Prioridad de transmisin de
187 fax
No se utiliza
200 Polling manual
460
No se utiliza
Tablas SP principales-5
Registro: Estado
Muestra un nmero que indica el estado del dispositivo del servicio @Remote.
0: Ni el dispositivo @Remote ni el RCG Gate incrustado estn configurados.
1: Se est configurando el RCG Gate incrustado. Se ha completado el registro Only Box.
201 En este estado, el dispositivo @Remote no se puede comunicar con este dispositivo.
2: El RCG Gate incrustado est configurado. En este estado, el dispositivo @Remote no
se puede comunicar con este dispositivo.
3: El dispositivo @Remote se est configurando. En este estado, no se puede configurar el
RCG Gate incrustado.
4: El mdulo @Remote no se ha iniciado.
202 Nmero carta
461
Registrar resultado
Muestra un nmero que indica el resultado del registro.
0: Correcto
2: Ejecucin del registro
3: Error del proxy (proxy activado)
207 4: Error del proxy (proxy desactivado)
5: Error del proxy (nombre o contrasea de usuario ilegales)
6: Error de comunicacin
7: Error de actualizacin de la certificacin
8: Otro error
Cdigo
Significado
-11001
Error de funcionamiento,
configuracin incorrecta
462
-11003
Error inesperado
-12002
-12003
-12004
Tablas SP principales-5
-12005
-12006
-12007
-12008
-2385
-2387
-2389
-2390
-2391
-2392
Error de parmetro
-2393
-2394
Dispositivo no gestionado
-2395
-2396
-2397
-2398
463
*CTL
Carga los datos de modo UP y SP (salvo en el caso de los contadores y del nmero de
serie) desde la NVRAM a una tarjeta SD. Para obtener detalles, consulte el manual de
servicio de campo.
001 -
Descarga los datos de modo UP y SP desde una tarjeta SD a la NVRAM. Para obtener
detalles, consulte el manual de servicio de campo.
001 -
5828
[Configuracin de red]
Compatibilidad 1284
050
(Centro)
*CTL
0: Desactivado, 1: Activado
Este SP slo se activa cuando SP5-828-50 est
configurado en "1".
Activa/desactiva la funcin de colas de trabajos.
[0 o 1 / 0 / 1 /incremento]
0: Desactivado, 1: Activado
464
Tablas SP principales-5
066
bit1: FTP
bit2: IPP
bit3: SMB
bit4: BMLinkS
bit5: DIPRINT
bit6: sftp
bit7: (Reservado)
TELNET (0: Desactivado 1:
090
Activado)
[0 o 1 / 1 / ]
0: Desactivar, 1: Activar
ste es el enlace de direccin local IPv6 referido en la
Ethernet o LAN inalmbrica (802.11b) en el formato:
145
465
147
149
151
153
155
5
156 Direccin manual de IPv6
161
Configuracin automtica
IPv6 sin estado
466
Tablas SP principales-5
237
238
5832
467
005
001
002
[Ajustes de captura]
*CTL
0: Desactivar, 1: Activar
Con esta funcin desactivada, los ajustes relacionados con la funcin de captura no se
pueden inicializar, mostrar ni seleccionar.
Ajuste del panel
0: Mostrado, 1: No mostrado
468
Tablas SP principales-5
073 Reduccin para copias de otros en B/N 0: 1a-1, 1: 1/2, 2: 1/3, 3: 1/4
074 Reduccin para impresiones a color
076
2: TIFF/MH, 3: TIFF/MR
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
Este SP no se utiliza en este modelo.
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
[5 a 95 / 50 / 1 /incremento]
091 Establece el formato JPEG predeterminado para los documentos enviados al servidor de
gestin documental va la MLB con JPEG seleccionado como formato.
Slo est habilitado si la MLB (Media Link Board) opcional est instalada.
469
101
Direccin IP de servidor
primario
102
Esquema de servidor
primario
103
Nmero de puerto de
servidor primario
104
111
Direccin IP de servidor
secundario
112
Esquema de servidor
secundario
113
114
120
Interruptor de tasa de
resolucin predeterminada
[De 0 a 3 / 2 / 1/incremento]
121 Selecciona la resolucin para el modo de copia en color. Esto lo ajusta bsicamente el
sistema remoto.
0: 600dpi/ 1: 300dpi/ 2: 150dpi/ 3: 75dpi
Resolucin: Copia (Mono)
[De 0 a 5 / 3 / 1/incremento]
122 Selecciona la resolucin para el modo de copia en B/N. Esto lo ajusta bsicamente el
sistema remoto.
0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi
Resolucin: Impresin
(Color)
123 Selecciona la resolucin para el modo de impresin en color. Esto lo ajusta bsicamente
el sistema remoto.
0: 600dpi/ 1: 300dpi/ 2: 150dpi/ 3: 75dpi
470
Tablas SP principales-5
Resolucin: Impresin
(Mono)
124 Selecciona la resolucin para el modo de impresin en B/N. Esto lo ajusta bsicamente
el sistema remoto.
0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi
5840
[IEEE 802.11]
[De 1 a 11 o 13 / 11 o 13 / 1 /incremento]
Canales MAX
*CTL
Europa/Asia: 1 a 13
NA/ Asia: 1 a 11
No cambie la configuracin.
[De 1 a 11 o 13 / 1 / 1 /incremento]
Canales MIN
*CTL
Europa: 1 a 13
NA/ Asia: 1 a 11
471
[De 0 x 00 a 0 x FF / 0 x FF a Auto / -]
0 x FF a Auto [Predeterminado]
0 x 11 55M Fijo
0 x 10 - 48M Fijo
0 x 0F - 36M Fijo
0 x 0E 18M Fijo
0 x 0D - 12M Fijo
008 Velocidad de transmisin
*CTL
0 x 0B - 9M Fijo
0 x 0A - 6M Fijo
0 x 07 - 11M Fijo
0 x 05 - 5,5M Fijo
0 x 08 - 1M Fijo
0 x 13 - 0 x FE (reservado)
0 x 12 - 72M (reservado)
0 x 09 - 22M (reservado)
Selecciona la clave WEP.
[De 00 a 11 / 00 / 1 binario]
011 Seleccin de clave WEP
*CTL
00: Clave #1
01: Clave #2 (reservada)
10: Clave #3 (reservada)
11: Clave #4 (reservada)
Ajusta el umbral de fragmento para la tarjeta
IEEE802.11.
*CTL
[256 a 2346/2346/1]
Este SP slo se visualiza cuando la tarjeta
IEEE802.11 est instalada.
Determina si la funcin CTS self est habilitada
o deshabilitada.
*CTL
[0 o 1 / 1 / 1] 0: Desactivado 1: Activado
Este SP slo se visualiza cuando la tarjeta
IEEE802.11 est instalada.
472
Tablas SP principales-5
*CTL
*CTL
[1 a 3/3/1]
1: Info, 2: advertencia, 3: error
Este SP slo se visualiza cuando la tarjeta
IEEE802.11 est instalada.
5841
002
003
004
*CTL
007 OrgStamp
[USB]
001
Velocidad de transferencia
*CTL
473
*CTL
5845
*CTL
001 Establece el nmero de puerto FTP utilizado al digitalizar archivos hacia el servidor Scan
Router.
Direccin IP (Primaria)
002 Utilice este SP para establecer la direccin del servidor Scan Router. La direccin IP en la
pestaa de transferencia se puede consultar por el ajuste de sistema inicial.
Tiempo de presentacin del error de
[De 0 a 999 / 300 / 1 segundo /incremento]
entrega
006 Utilice este ajuste para determinar la cantidad de tiempo que debe mostrarse el mensaje
emergente cuando se produce un error de prueba durante la transferencia de documento
con la aplicacin NetFile y un dispositivo externo.
Direccin IP (Secundaria)
[De 0 a 4 / 0 / 1 /incremento]
Permite cambiar el modelo del servidor de entrega registrado por el dispositivo de E/S.
0: Desconocido
009 1: SG1 proporcionado
2: Paquete SG1
3: SG2 proporcionado
4: Paquete SG2
474
Tablas SP principales-5
Bit7 = Limitacin del uso 1 libreta direcciones (Limitacin para cada usuario autorizado)
Bit6 = 1 enlace autorizacin RDH
Bit5 a 0: No utilizado
Control envo rpido
022
5846
[Configuracin UCS]
*CTL
Muestra la ID
001 Muestra la nica ID del dispositivo en uso por el directorio del servidor de entrega. El
valor slo se muestra y no se puede cambiar. Este ID se crea desde la NIC MAC o IEEE
1394 EUI. La ID se muestra como un binario de 6-byte u 8-byte.
475
Borra la ID
006
476
Tablas SP principales-5
Procedimiento
1. Apague la mquina.
2. Instale un disco duro nuevo.
3. Encienda la mquina.
4. La libreta de direcciones y sus datos iniciales se crean automticamente en el disco
duro.
1: Ranura SD 1
2: Ranura SD 2
4: ROM Flash USB
20: Disco duro
30: Nada
047
048
049
477
050
051
052
Opcin de bsqueda
Este SP utiliza bit switches para configurar las opciones de bsquedas parciales de la
libreta local de direcciones UCS.
Bit: Significado
060 0: Comprueba los caracteres que distinguen entre maysculas y minsculas
1: Slo Japn
2: Slo Japn
3: Slo Japn
4 a 7: No se utilizan
478
Tablas SP principales-5
[De 0 a 32 / 0 / 1 /incremento]
Este SP no suele requerir ajuste.
Este SP se activa nicamente despus de que el administrador del sistema haya
configurado una poltica de contrasea de grupo para controlar el acceso a la libreta
de direcciones.
*CTL
[0 a 5 / 2 / 1 /en incrementos de 1]
SP5847-21 establece la calidad de imagen JPEG de los archivos de imagen gestionados
por NetFile.
"Net files" (archivos de red) son trabajos para imprimir desde el Document Server usando
un PC y el software DeskTopBinder.
001 Velocidad para copia a color
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
479
*CTL
5848
5848 100 establece el tamao mximo permitido para imgenes descargadas. El valor
predeterminado es de 1 gigabyte.
007
009
480
Tablas SP principales-5
5849
[Fecha de instalacin]
5849 1 Presentacin
[0 o 1 / 1 /-]
0: OFF (no se imprime)
1: ON (se imprime)
5853
Utilice este SP para descargar los datos de sello fijos almacenados en el firmware de la
ROM y cpielos en el disco duro. Este SP se puede ejecutar todas las veces que sea
necesario. Este SP se debe ejecutar despus de sustituir o formatear el disco duro.
Este SP se puede ejecutar nicamente con el disco rudo instalado.
[Remote ROM Update] ([Actualizacin de ROM remota])
5856
*CTL
0: Desactivar
1: Activar
481
5857
*CTL
0: DESACTIVADO, 1: ACTIVADO
482
Tablas SP principales-5
*CTL
0: Desactivado, 1: Activado
003 Cualquier Error SC
004 Atasco
5859
*CTL
483
001 Key 1
002 Key 2
003 Key 3
004 Key 4
005 Key 5
006 Key 6
007 Key 7
008 Key 8
009 Key 9
010 Key 10
5860
020
[SMTP/POP3/IMAP4]
*CTL
[De 1 a 168 / 72 / ]
Configura cunto tiempo deber esperarse para guardar un correo que se interrumpe en
el momento de recibirse. El correo recibido se descartar si la parte que queda por recibir
no se recibe durante el tiempo especificado.
021
[De 0 a 1 / 0 / ]
484
[0 o 1 / 0 / ]
Tablas SP principales-5
S/MIME: Configuracin de
encabezado MIME
[0 a 2/0/1]
0: Microsoft Outlook Express estndar
*CTL
*CTL
5870
001 Escritura
*CTL
485
Inicializar
*CTL
Deshacer
002
ejecutables
5875
001
Configuracin de
reinicio
*CTL
*CTL
[0 o 1 / 0 /-]
0: Reinicio manual, 1: Reinicio automtico
5878
486
[Configuracin de opciones]
Tablas SP principales-5
5881
001 -
5884
*ENG
*ENG
002 Bandeja 1
*ENG
003 Bandeja 2
*ENG
004 Bandeja 3
*ENG
005 Bandeja 4
*ENG
5885
5
[0 o 1 / 1 /-]
0: Papel normal 1
1: Papel normal 2
020
487
*CTL
*CTL
Establecer firma
*CTL
100
*CTL
*CTL
No se utiliza
*CTL
No se utiliza
5887
488
Tablas SP principales-5
001 -
*CTL
001 -
*CTL
5894
[De 0 a 2 / 0 / 1/incremento]
[Prioridad Copia/Impresora]
-
[0 o 1 / 0 /-]
001 Selecciona la prioridad del tipo de memoria. La memoria mayor se utiliza para el modo
seleccionado (copia o impresora).
0: Prioridad copia, 1: Prioridad impresora
5907
Establece el nombre de marca y el nombre de produccin para Windows Plug & Play. Esta
informacin se almacena en la NVRAM. Si la NVRAM es defectuosa, ser necesario volver
001 a registrar estos nombres.
Despus de seleccionar, pulse la tecla "Original Type" (Tipo de original) y la tecla "#" al
mismo tiempo. Cuando se ha completado el ajuste, sonar un bip cinco veces.
5913
*CTL
[3 a 30 / 3 / en incrementos de 1
segundo]
002 Establece la cantidad de tiempo que debe pasar la mquina en modo de espera (y no se
han utilizado las teclas del panel de mandos) antes de que otra aplicacin pueda obtener
el control de la pantalla.
5967
*CTL
0: Activado, 1: Desactivado
Activa y desactiva el Document Server. Esta es una medida de seguridad que evita que se
dejen los datos de imagen en el rea temporal del disco duro. Despus de cambiar este
001
ajuste, debe apagar y volver a encender el interruptor principal para habilitar el nuevo
ajuste.
5974
[Servidor Cherry]
Especifica qu versin de ScanRouter, "Lite" o "Full", est instalada.
*CTL
[0 o 1 / 0 / ]
0: Lite, 1: Full
[Configuracin de dispositivo]
5985
490
Tablas SP principales-5
[De 0 a 2 / 0 / 1 /incremento]
0: Desactivar, 1: Activar, 2: Limitacin funcin
Cuando est configurada la "Function limitation" (Limitacin
de funcin), la "On board NIC" (NIC incorporada) slo est
limitada para la autenticacin de NRS o LDAP/NT.
001 NIC incorporada
No habr otras aplicaciones de red disponibles
aparte de @Remote o la autenticacin LDAP/NT
cuando este SP est ajustado en "2". Aunque puede
cambiar los ajustes iniciales de dichas aplicaciones de
red, estos ajustes no funcionarn.
002 USB incorporada
5987
0: Desactivar, 1: Activar
5990
[0 o 1 / 0 / 1 /en incrementos de 1]
491
006 No predeterminada
021
Programa de usuario de la
copiadora
022 SP de escner
023
001
5997
[0 o 1 / 1 /-]
0: Off, 1: On
492
Tablas SP principales-6
Tablas SP principales-6
SP6-XXX (Perifricos)
6006
[Ajuste de ADF]
Ajusta el registro de lado a lado y del borde anterior de los originales con el ARDF.
*ENG
Ajusta la cantidad de ondulacin del papel para corregir la desviacin del original por
delante y por detrs.
005 Curva: dplex: 1
006 Curva: dplex: 2
*ENG
*ENG
Muestra las seales recibidas desde los sensores y los conmutadores del ARDF. Slo el bit
0 se usa para comprobacin de entrada de ADF ( "Tabla de comprobacin de entrada"
en esta seccin").
[Comprobacin de SALIDA ADF]
6008
6009
493
6010
001 -
6016
*ENG
0: Configuracin 1
1: Configuracin 2
5
001 -
NA
EU/
Asia
6017
Ajuste 1
Ajuste 2
DLT SEF
LG SEF
Foolscap SEF
LT SEF
LT LEF
US EXE LEF
DLT SEF
8K 267 x 390 mm
LT SEF
LT LEF
001 -
*CTL
001 494
ENG
Tablas SP principales-6
6102
6103
001 -
6104
ENG
ENG
ENG
Muestra las seales recibidas desde los sensores y los conmutadores del finisher. (
de comprobacin de entrada" en esta seccin")
"Tabla
Muestra las seales recibidas desde los sensores y los conmutadores del finisher. (
de comprobacin de salida" en esta seccin")
"Tabla
495
Tablas SP principales-7
SP7-XXX (Registro de datos)
7401
001 -
*CTL
[Historial de SC]
7403
001 Ms reciente
002 Reciente 1
003 Reciente 2
004 Reciente 3
005 Reciente 4
006 Reciente 5
*CTL
007 Reciente 6
008 Reciente 7
009 Reciente 8
010 Reciente 9
7502
001 -
496
*CTL
Tablas SP principales-7
7503
001 -
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
497
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
241
498
*CTL
*CTL
*CTL
*CTL
245
7505
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
Tablas SP principales-7
001 Al encender
003 Correccin de desviacin: Activada
004 Registro: Activado
005 Salida de papel: Activado
*CTL
7506
006 A5 LEF
014 B5 LEF
038 LT LEF
044 HLT LEF
132 A3 SEF
133 A4 SEF
134 A5 SEF
*CTL
141 B4 SEF
142 B5 SEF
160 DLT SEF
164 LG SEF
166 LT SEF
172 HLT SEF
255 Otros
499
7507
001 Ms reciente
002 Reciente 1
003 Reciente 2
004 Reciente 3
005 Reciente 4
006 Reciente 5
*CTL
007 Reciente 6
008 Reciente 7
009 Reciente 8
010 Reciente 9
7508
7624
500
*CTL
Tablas SP principales-7
001 PCU: Bk
*CTL
002 PCU: M
*CTL
003 PCU: C
*CTL
004 PCU: Y
*CTL
*CTL
*CTL
*CTL
[0 o 1 / 1 /-]
*CTL
Banda de transferencia de
009
imagen
010
*CTL
*CTL
*CTL
*CTL
7803
*CTL
013
7801
Unidad de limpieza de la
ITB
1: S (Mantenimiento PM)
*CTL
501
De -001 a
-021 Cuando una unidad se cambia, la mquina detecta automticamente la instalacin de
una nueva mquina. A continuacin, el valor del contador PM en curso se desplaza
automticamente al Contador PM - anteriormente (SP7-906-1 a 21) y se reinicia en "0".
Con SP7-906-1 to 21 se puede comprobar el nmero total de hojas impresas con la ltima
unidad.
001 Papel
002 Pgina: PCU: Bk
502
Tablas SP principales-7
503
504
Tablas SP principales-7
De -091 a
-108 El contador Pgina% est basado en impresiones, no en revoluciones. Si el nmero de
copias impresas alcanza el lmite, la mquina entra la condicin final para esa unidad. Si
se alcanza primero la vida til del contador de revoluciones, la mquina tambin entra
en la condicin final, aunque el contador Pgina% an sea inferior al 100%.
*ENG
[De 0 a 255 / - / 1 %/
incremento]
505
*ENG
[De 0 a 255 / - / 1 %/
incremento]
5
7804
506
Tablas SP principales-7
7807
001 7826
*CTL
*CTL
*CTL
7827
*CTL
507
7832
001 7835
[Contador ACC]
--
7836
*CTL
001 -
*CTL
7852
7853
508
*CTL
*CTL
[Contador de cambio]
Muestra el nmero de cambio de las piezas de repuesto.
Tablas SP principales-7
001 PCU: Bk
*CTL
002 PCU: C
*CTL
003 PCU: M
*CTL
004 PCU: Y
*CTL
*CTL
*CTL
*CTL
*CTL
009 Revelador: Bk
*CTL
010 Revelador: C
*CTL
011 Revelador: M
*CTL
012 Revelador: Y
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
019
*CTL
020
*CTL
509
[Intervalo de cobertura]
Ajusta el umbral de cobertura del color.
Tasa de cobertura = Cobertura por pgina / cobertura completa A4 (puntos) x 100
Existen tres contadores de cobertura: Color 1, Color 2, y Color 3
[A] 5% (valor predeterminado) es ajustable mediante SP7855-001.
[B] 20% (valor predeterminado) es ajustable mediante SP7855-002.
7855
El valor de ajuste [B] se debe ajustar de manera que sea mayor que [A].
Los nmeros totales de copias impresas (impresin B/N ms impresin en color) para cada
rango de cobertura se muestra con los siguientes SP.
Contador Color1: SP8601-021
7906
*CTL
[1 a 200/5/1]
*CTL
[1 a 200/20/1]
*ENG
De -001 a Muestra el nmero de hojas impresas con las unidades de mantenimiento anteriores.
-020 [De 0 a 9999999 / 0 / 1 pgina/incremento]
001 Pgina: PCU: Bk
002 Pgina: PCU: C
003 Pgina: PCU: M
004 Pgina: PCU: Y
005 Pgina: Unidad de revelado: Bk
006 Pgina: Unidad de revelado: C
007 Pgina: Unidad de revelado: M
008 Pgina: Unidad de revelado: Y
009 Pgina: Revelador: Bk
510
Tablas SP principales-7
511
512
Tablas SP principales-7
513
7931
514
*ENG
*EGN
*EGN
*EGN
005 ID de producto
*EGN
*EGN
*EGN
*EGN
*EGN
010 Fecha
*EGN
011 N de serie
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
Tablas SP principales-7
7932
[Botella de tner M]
Muestra informacin de la botella de tner para M.
001 ID de serie de la mquina
*ENG
*EGN
*EGN
*EGN
005 ID de producto
*EGN
*EGN
*EGN
*EGN
*EGN
010 Fecha
*EGN
011 N de serie
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
7933
[Botella de tner C]
Muestra informacin de la botella de tner para C.
515
7934
516
*ENG
*EGN
*EGN
*EGN
005 ID de producto
*EGN
*EGN
*EGN
*EGN
*EGN
010 Fecha
*EGN
011 N de serie
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
[Botella de tner Y]
Muestra informacin de la botella de tner para Y.
Tablas SP principales-7
7935
*ENG
*EGN
*EGN
*EGN
005 ID de producto
*EGN
*EGN
*EGN
*EGN
*EGN
010 Fecha
*EGN
011 N de serie
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
517
001 N de serie
002 Fecha del anexo
003 Anexo: Contador total
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
518
Tablas SP principales-7
005 N de serie
006 Fecha del anexo
007 Anexo: Contador total
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
519
009 N de serie
010 Fecha del anexo
011 Anexo: Contador total
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
520
Tablas SP principales-7
013 N de serie
014 Fecha del anexo
015 Anexo: Contador total
*ENG
*ENG
7950
*ENG
*EGN
*EGN
*EGN
*EGN
*EGN
013 PCU: Bk
*EGN
014 PCU: C
*EGN
015 PCU: M
*EGN
016 PCU: Y
*EGN
521
*EGN
*EGN
*EGN
*EGN
021 Revelador: Bk
*EGN
022 Revelador: C
*EGN
023 Revelador: M
*EGN
024 Revelador: Y
*EGN
*ENG
522
Tablas SP principales-7
523
7952
*EGN
Rotacin: Unidad de
limpieza de ITB
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
002
007
008
Cantidad:Botella de
recogida de tner de ITB
Cantidad:Botella de
recogida de tner de PCU
524
Pgina: Almohadilla de
fusin
*EGN
*EGN
*EGN
*EGN
Tablas SP principales-7
*EGN
*EGN
*EGN
*EGN
025
*EGN
026
*EGN
027
*EGN
028
*EGN
029
*EGN
030
*EGN
031
*EGN
*EGN
*EGN
034
*EGN
035
*EGN
036
*EGN
037
*EGN
525
*EGN
[De 0 a 999999999 / 0 / 1 mm/incremento]
042
Rotacin: Unidad de
revelado: Bk
*EGN
043
Rotacin: Unidad de
revelado: C
*EGN
Rotacin: Unidad de
044
revelado: M
*EGN
Rotacin: Unidad de
revelado: Y
*EGN
045
*EGN
*EGN
*EGN
Pgina: Unidad de
revelado: Bk
055
Pgina: Unidad de
revelado: C
Pgina: Unidad de
056
revelado: M
057
526
Pgina: Unidad de
revelado: Y
Tablas SP principales-7
*EGN
7953
063
Umbral de da:Botella de
recogida de tner de ITB
064
Umbral de da:Botella de
recogida de tner de PCU
*EGN
*CTL
527
7954
528
*CTL
Tablas SP principales-8
Tablas SP principales-8
Tablas de comprobacin de entrada y salida
Tabla de comprobacin de entrada
Cuando se introduce el modo de comprobacin de entrada, 8 dgitos muestran el resultado de una seccin.
Cada dgito corresponde a un dispositivo diferente tal como se ilustra en la tabla.
N. Bit
Resultado
01
01
01
01
01
01
01
01
Copiadora
5803
Descripcin
Lectura
0
Normal
Bloqueo
Normal
Bloqueo
Normal
Bloqueo
Normal
Bloqueo
Normal
Bloqueo
Normal
Bloqueo
Normal
Bloqueo
Bias Ventilador
delantero:BLOQUEO
Normal
Bloqueo
Normal
Bloqueo
Ventilador de salida de
fusin:BLOQUEO
Normal
Bloqueo
Normal
Bloqueo
5803 5
5803 8
5803 10
Motor fusin/salida
papel:BLOQUEO
529
5803 12
Normal
Bloqueo
Nueva
No es nueva
No detectado
Detectada
Papel detectado
No se detecta el papel
Actuador no
detectado
Actuador detectado
Actuador no
detectado
Actuador detectado
Compuerta del
inversor abierta
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Posicin inicial
No posicin inicial
5803 23 HVPS:CB
5803 24 HVPS:T
530
5803 25
Puerta cerrada
Puerta abierta
5803 26
Tapa cerrada
Tapa abierta
No instalado
Instalado
No instalado
Instalado
Instalado
No instalado
Instalado
No instalado
Agotado
No agotado
Agotado
No agotado
Tablas SP principales-8
Agotado
No agotado
Agotado
No agotado
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Posicin inicial
(Contacto)
No posicin inicial
5803 38
5803 39
Instalado
No instalado
5803 40
Instalado
No instalado
5803 41
Llena
No est llena
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
(sin contacto)
5803 44
SW de deteccin de tamao de
bandeja1
5803 45
SW de deteccin de tamao de
bandeja2
5803 46
SW de deteccin de tamao de
bypass
5803 47
Detectada
No detectada
Posicin inicial
No posicin inicial
5803 49
No agotado
Agotado
5803 50
No agotado
Agotado
No agotado
Agotado
531
Instalado
No instalado
Instalado
No instalado
Puerta cerrada
Puerta abierta
Puerta cerrada
Puerta abierta
5803 56 DIP SW
No instalado
Instalado
Bloqueo
Normal
Papel detectado
No se detecta el
papel
Instalado
No instalado
Papel detectado
No se detecta el
papel
Papel detectado
No se detecta el
papel
Instalado
No instalado
5803 58
5803 70
Bandeja de desplazamiento:Sensor
de medio giro
No posicin inicial
Posicin inicial
5803 76
No instalado
Instalado
Lmite superior
Abierta
Cerrada
No instalado
Instalado
No agotado
Agotado
532
Tablas SP principales-8
5803 83
2T PFU:Sensores de tamao
superiores
2T PFU:Sensores de tamao
5803 84
inferiores
5803 85
Lmite superior
5803 86
Lmite superior
5803 87
5803 88
Abierta
Cerrada
No agotado
Agotado
No agotado
Agotado
Papel detectado
No se detecta el
papel
No posicin inicial
Posicin inicial
Abierta
Cerrada
Comprobacin de LD desactivado:
Fbrica
Bit
Norteamrica
Europa/Asia
A3 SEF*1
(A3 SEF)
533
B4 SEF*2
(B4 SEF)
A4 SEF
A4 SEF
B5 SEF
B5 SEF
A4 LEF*3
(A4 LEF)
B5 LEF*4
(B5 LEF)
A5 LEF
A5 LEF
*1: La mquina detecta si es 11" x 17" SEF o A3 SEF, en funcin del ajuste de SP 5-181-002 (Bandeja
1) o SP 5-181-006 (Bandeja 2).
*2: La mquina detecta si es 8,5" x 14" SEF o B4 SEF, en funcin del ajuste de SP 5-181-003 (Bandeja
1) o SP 5-181-007 (Bandeja 2).
*3: La mquina detecta si es 11" x 81/2" LEF o A4 LEF, en funcin del ajuste de SP 5-181-001 (Bandeja
1) o SP 5-181-005 (Bandeja 2).
*4: La mquina detecta si es B5 LEF o 10,5" x 7,25" LEF, en funcin del ajuste de SP 5-181-004
(Bandeja 1) o SP 5-181-008 (Bandeja 2).
Tabla 2: Tamao de papel (Mesa bypass):
0: ACTIVADO, 1: DESACTIVADO
Sensor de tamao de papel bypass
534
bit3
Bit2
Bit1
Bit0
Sensor de
longitud
HLT SEF
B6 SEF
HLT SEF
A5 SEF
HLT SEF
A5 SEF
LT/LG SEF*1
A4 SEF
LT/LG SEF*1
A5 LEF
DLT SEF
A3 SEF
NA
UE/ASIA
Tablas SP principales-8
Bit2
Bit1
Bit0
Sensor de
longitud
NA
UE/ASIA
LT LEF
A4 LEF
Sensor de anchura
Visualizacin
SP4-301
Versin mtrica
Versin en
pulgadas
W1
W2
W3
L1
L2
A3
11" x 17"
00000011
B4
10" x 14"
00000011
F4
8,5" x 13", 8,25" x 13",
o 8" x 13"
8,5" x 14"
00000011
A4 LEF
8,5" x 11"
00000000
B5 LEF
00000000
A4 SEF
11" x 8,5"
00000010
B5 SEF
00000010
A5 LEF/ SEF
5,5" x 8,5",
8,5" x 5,5"
00000000
SP 5126 controla el
tamao que se detecta
Bit
Europa/Asia
535
A3 SEF*1
(A3 SEF)
B4 SEF*2
(B4 SEF)
A4 SEF
A4 SEF
B5 SEF
B5 SEF
A4 LEF*3
(A4 LEF)
B5 LEF*4
(B5 LEF)
A5 LEF
A5 LEF
A5 SEF
A5 SEF
*1: La mquina detecta si es 11" x 17" SEF o A3 SEF, en funcin del ajuste de SP 5-181-010 (Bandeja
3) o SP 5-181-014 (Bandeja 4).
*2: La mquina detecta si es 8,5" x 14" SEF o B4 SEF, en funcin del ajuste de SP 5-181-011 (Bandeja
3) o SP 5-181-015 (Bandeja 4).
*3: La mquina detecta si es 11" x 81/2" LEF o A4 LEF, en funcin del ajuste de SP 5-181-009 (Bandeja
3) o SP 5-181-013 (Bandeja 4).
*4: La mquina detecta si es B5 LEF o 10,5" x 7,25" LEF, en funcin del ajuste de SP 5-181-012 (Bandeja
3) o SP 5-181-016 (Bandeja 4).
ARDF (D366)
6007
536
Descripcin
Lectura
0
6007 1
No se detecta el papel
Papel detectado
6007 2
No se detecta el papel
Papel detectado
6007 3
No se detecta el papel
Papel detectado
Tablas SP principales-8
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
Posicin inicial
No posicin inicial
Descripcin
Lectura
0
6120 1
No posicin inicial
Posicin inicial
6120 2
No posicin inicial
Posicin inicial
6120 3
No posicin inicial
Posicin inicial
No se detecta el papel
Papel detectado
Subido
Bajado
No se detecta el papel
Papel detectado
Bajado
Subido
No se detecta el papel
Papel detectado
537
Posicin inicial
No posicin inicial
Posicin inicial
No posicin inicial
Normal
Bloqueo
Cerrada
Abierta
6120 9
6120 10
6120 13
Unidad de perforacin:Deteccin de
rea2
Unidad de perforacin:Deteccin de
6120 14
rea1
Posicin inicial
No posicin inicial
Posicin inicial
No posicin inicial
No posicin inicial
Posicin inicial
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
No se detecta el papel
Papel detectado
Llena
No est llena
Superior
No superior
No se detecta el papel
Papel detectado
Inferior
No inferior
No posicin inicial
Posicin inicial
No posterior
Posicin trasera
Sin grapa
Grapa detectada
Sin grapa
Grapa detectada
538
Tablas SP principales-8
No instalado
Instalado
2/3
4 (EU)
4 (Escan.)
6120-013
Unidad de perforacin:Deteccin
de rea2
6120-014
Unidad de perforacin:Deteccin
de rea2
Presentacin
Descripcin
5804 1
5804 2
5804 3
5804 4
5804 5
5804 6
5804 7
5804 8
539
540
5804 9
5804 10
5804 11
5804 12
5804 13
5804 14
5804 15
5804 16
Tablas SP principales-8
5804 53 Motor de fusin/Salida de papel:120 mm/s 5804 54 Motor de fusin/salida de papel:60 mm/s
541
5804 69
5804 70
542
Tablas SP principales-8
543
544
5804 130
5804 131
5804 132
5804 133
5804 134
Tablas SP principales-8
Descripcin
Descripcin
ARDF (D366)
6008
Presentacin
Descripcin
Motor de alimentacin-rotacin hacia delante
545
546
Solenoide de marcador
Tablas SP principales-9
Tablas SP principales-9
Modo de servicio de impresora
SP1-XXX (Modo de servicio)
1001
Bit Switch
bit 0
DFU
bit 1
DFU
bit 2
DFU
0:
Desactivar
1: Activar
bit 3
Activado: El ajuste de tiempo de espera de E/S de MFP no tendr efecto. Los tiempos
de espera de E/S no se producirn nunca.
bit 4
0:
Desactivar
1: Activar
DFU
bit 6
DFU
0:
Desactivar
1: Activar
bit 7
Activado: la mquina imprime todos los trabajos de RPCS y PCL con un margen en los
bordes del rea de impresin.
1001
Bit Switch
547
bit 0
DFU
bit 1
DFU
bit 2
Desplazar
clasificacin
Clasificacin
normal
0: Activar
1: Desactivar
1001
548
bit 4
DFU
bit 5
DFU
bit 6
DFU
bit 7
DFU
Bit Switch
Tablas SP principales-9
bit 0
DFU
bit 1
DFU
bit 2
0:
Desactivar
1: Activar
Activado: Utiliza el mismo margen izquierdo que los modelos anteriores de HP como
HP4000/HP8000.
Es decir, el margen izquierdo definido en el trabajo (normalmente "<ESC>*r0A") se
cambiar por "<ESC>*r1A"
1001
bit 3
DFU
bit 4
DFU
bit 5
DFU
bit 6
DFU
bit 7
DFU
Bit Switch
DFU
bit 1
DFU
bit 2
DFU
bit 3
0:
Desactivar
1: Activar
Si est activado, las pginas simplex de los trabajos IPDS se imprimirn en el lado
frontal debido a la impresin en el dorso de la pgina. Esto puede reducir la velocidad
de impresin.
bit 4
DFU
bit 5
DFU
bit 6
DFU
bit 7
DFU
549
1001
Bit Switch
Desactivar
Activar
bit 1
0:
Desactivar
(Una sola
copia)
1: Activar
(Varias copias)
DFU
bit 3
[PS] Criterios de PS
Patrn3
Patrn1
Desactivar
(100)
Activar (1000)
Desactivar
Activar
550
Tablas SP principales-9
bit 6
0:
Desactivar
1: Activar
1001
0:
Desactivar
1: Activar
Bit Switch
Si est activado, las pginas simples (slo en trabajos mixtos de simple/dplex PS/
PCL5) y la ltima pgina de un trabajo dplex con un nmero impar de pginas (PS,
PCL5, PCL6), pasan siempre por la unidad dplex. No tener que conmutar entre rutas
de papel incrementa ligeramente la velocidad de impresin.
bit 1 a
DFU
7
1001
1: Activar
(Dplex)
Bit Switch
0:
Desactivar
Bit Switch
551
bit 0
DFU
bit 1
DFU
bit 2
DFU
bit 3
Desactivar
Activar
Activar: Los trabajos B/N entregados sin un cdigo de usuario se imprimirn incluso
si la autenticacin de cdigo de usuario est activada.
Los trabajos en color no se imprimirn sin un cdigo de usuario vlido.
1001
bit 4
DFU
bit 5
DFU
bit 6
DFU
bit 7
DFU
"Desactivad
o
"Activado
Bit Switch
(Inmediata
mente)"
(10 segundos)"
552
DFU
Tablas SP principales-9
bit 2
Desactivad
o
(No
cancelado)
Activado
(Cancelado)
Si este bit se conmuta, todos los trabajos se cancelarn despus de que se produzca
un atasco.
Nota: Si este Bit Switch est activado, la impresin bajo las siguientes condiciones
puede provocar problemas:
- Entrega de trabajo a travs de USB o puerto paralelo
- Impresin de cola de impresin (WIM >Configuracin > Ajustes de dispositivo >
Sistema)
bit 3
0:
Desactivar
1: Activar
[Borrar ajuste]
Inicializar sistema de impresora
Inicializa la configuracin del men Sistema del modo del usuario.
[Imprimir resumen]
553
Imprimir resumen
1004 1 Imprime la hoja de resumen de servicio (resumen de todos los valores de configuracin del
controlador).
1005
1005 1
1006
[Mostrar versin]
Disp. Versin
Muestra la versin del firmware del controlador.
[Muestra/Impresin
bloqueada]
*CTL
0: Enlazado, 1: Activado
Activa y desactiva el Document Server. Cuando selecciona "0," el document server se activa
1006 1 o desactiva de acuerdo con Copy Service Mode SP5-967. Cuando selecciona "1," el
document server se activa sin importar Copy Service Mode SP5-967.
[Recuperacin de datos]
1101
Recuerda un conjunto de ajustes gamma. Esto puede ser a) los ajustes de fbrica, b) el ajuste
anterior, o c) el ajuste en curso.
1101 1 Fbrica
1101 2 Anterior
1101 3 Actual
*CTL
1101 4 ACC
1102
1102 1
[Ajuste de resolucin]
Selecciona el modo de impresin (resolucin) para el ajuste gamma de la impresora.
Fotografa 2400x600, Fotografa 1800x600, Fotografa 600 x 600, Texto 2400x600,
1800x600, Texto, Texto 600x600
[Pgina de prueba]
1103
Imprime la pgina de prueba para comprobar el equilibrio de color antes y despus del
ajuste gamma.
554
Tablas SP principales-9
*CTL
[De 0 a 30 / 15 / 1/incremento]
*CTL
[De 0 a 30 / 15 / 1/incremento]
Almacena el rango de impresin ajustada con el elemento de men "Ajus. gamma" como
el ajuste en curso. Antes de que la mquina almacene el "ajuste en curso", desplaza los
datos actualmente almacenados como el "ajuste en curso" a la ubicacin de
almacenamiento de memoria del "ajuste anterior".
555
1106
[Lmite de tner]
Ajusta la cantidad de tner mxima para el revelado de la imagen.
*CTL
Modo SP de escner
SP1-xxx (Sistema y otros)
1001
1001 5 -
1004
*CTL
[Tipo de compresin]
Selecciona el tipo de compresin del procesamiento binario de imgenes.
*CTL
[1 a 3 / 1 / 1 /en incrementos de 1]
1: MH, 2: MR, 3: MMR
[Margen de borrado]
1005
1005 1 Intervalo de 0 a 5 mm
1009
[Escaneo remoto
desactivado]
*CTL
*CTL
[De 0 a 5 / 0 / 1 mm/incremento]
[0 o 1 / 0 /-]
0: Activar, 1: Desactivar
1010
*CTL
556
[0 o 1 / 0 /-]
0: Presentacin, 1: Sin presentacin
Tablas SP principales-9
1011
*CTL
[0 o 1 / 0 /-]
1012
1012 1
1013
*CTL
[0 o 1 / 1 /-]
0: No, 1: S
*CTL
[0 o 1 / 0 /-]
0: Desactivado, 1: Activado
[De 5 a 95 / 20 / 1/incremento]
[De 5 a 95 / 40 / 1/incremento]
*CTL
[De 5 a 95 / 65 / 1/incremento]
[De 5 a 95 / 80 / 1/incremento]
[De 5 a 95 / 95 / 1/incremento]
Seleccciona el ratio de compresin para clearlight PDF para los dos ajustes que se pueden
seleccionar en el panel de operaciones.
557
558
[De 5 a 95 / 25 / 1/
incremento]
[De 5 a 95 / 20 / 1/
incremento]
Tipo de firmware
Tipo de firmware
Funcin
Motor
Aplicacin de
sistema/copia
Sistema operativo
Aplicacin de
Impresora
Aplicacin de funciones
Aplicacin Escner
Aplicacin de funciones
Aplicacin de fax
Aplicacin de funciones
NIB
Interface de red
Panel de mandos
Panel de mandos
Lcdc.
FCU de fax
Control de fax
FCU
GWFCU-4(ww)-1-1
Fax remoto
Control de fax
Firmware de idioma
Language (Idioma)
Motor
Idioma 1
Se pueden seleccionar 2
idiomas de entre 16.
Panel de mandos
WebDocBox
Aplicacin de servidor de
documentos
WebSys
Idioma 2
559
PS/PDF
Idioma de descripcin de la
Tarjeta SD de PS3
pgina (PostScript3)
PS3/ PDF
PictBridge
Control de PictBridge
Tarjeta SD PictBridge
PctBrgd
ARDF
Control ARDF
ARDF
ADF
Finisher (D429)
Control de finisher
Finisher (D429)
Finisher
Java VM
Aplicacin SDK
Tarjeta SD Java VM
SDK
Data Overwrite
Security
Aplicacin de seguridad
Tarjeta SD de
seguridad
Opcin de formato
de disco duro
Antes de empezar
Una tarjeta SD es un dispositivo de precisin. Observe siempre las siguientes precauciones cuando
manipule tarjetas SD:
Apague siempre el aparato antes de insertar una tarjeta SD. No inserte nunca la tarjeta SD en la
ranura con el aparato encendido.
No saque la tarjeta SD de la ranura de servicio despus de encender el aparato.
Nunca apague el aparato mientras se descarga el firmware de la tarjeta SD.
Conserve las tarjetas SD en un lugar seguro, donde no queden expuestas a temperatura o humedad
elevadas, ni a luz solar directa.
Manipule siempre las tarjetas SD con cuidado. No las doble ni arae. No exponga las tarjetas SD
a golpes ni vibraciones.
Asegrese de que la proteccin contra escritura de la tarjeta SD est desbloqueada al descargar
una aplicacin en ella. Si no, la descarga fallar y se producir un error de descarga (p. ej., Cdigo
de error 44) durante la actualizacin del firmware.
Tenga siempre en cuenta los siguientes puntos cuando utilice el programa de actualizacin de firmware:
"Cargar" significa enviar datos desde la mquina a la tarjeta SD. "Descargar" significa enviar datos
desde la tarjeta SD a la mquina.
Para seleccionar un elemento en la LCD, toque el botn correspondiente en la pantalla tctil de la
LCD o pulse la tecla numrica correspondiente en el teclado de 10 teclas del panel de mandos. Por
ejemplo, si aparece "Exit (0)" [Salir (0)], significa que puede pulsar el botn Exit en la pantalla o
pulsar el botn en el panel de mandos de la copiadora.
Antes de iniciar el procedimiento de actualizacin del firmware, asegrese de que el aparato est
desconectado de la red, a fin de evitar que llegue un trabajo de impresin mientras el firmware se
est actualizando.
560
Procedimiento de actualizacin
1. Apague el interruptor principal.
2. Quite la tapa de la ranura (
x 1).
Significado
Indica el nmero del mdulo y el nombre de la versin instalada en ese
momento. La primera lnea corresponde al nmero de mdulo y la segunda
al nombre de versin.
561
NEW:
No se pueden actualizar a la vez el firmware del controlador, del procesador y del panel de
mandos. Se recomienda actualizar los mdulos de firmware uno a uno.
9. Pulse "UpDate (#)" (o
Mensajes de error
Si se produce un error durante la descarga, se muestra un mensaje de error en la primera lnea.
El cdigo de error consta de la letra "E" y de un nmero. En el ejemplo anterior se muestra el error "E24".
Consulte los detalles en la tabla de mensajes de error. ( "Gestin de un error de actualizacin de
firmware")
562
Si la actualizacin de la ROM se interrumpe por causa de una prdida accidental de suministro elctrico
cuando el firmware se est actualizando, no se podr garantizar el correcto funcionamiento de la mquina
cuando sta se encienda de nuevo. Si la actualizacin de la ROM no se realiza correctamente por
cualquier motivo, y para garantizar el correcto funcionamiento de la mquina, el error de actualizacin
de ROM continuar mostrndose hasta que la ROM se actualice correctamente.
En este caso, inserte la tarjeta de nuevo y encienda la mquina para continuar con la descarga automtica
del firmware desde la tarjeta sin la pantalla de mens.
x 1).
563
11. El panel de operaciones se apaga y la tecla de encendido principal parpadea en rojo en intervalos
de 0,5 segundos cuando los datos se estn descargando. La misma tecla empieza a parpadear en
verde en intervalos de 1 segundo cuando la actualizacin finaliza.
12. Pulse el botn "Salir" (Exit).
13. Apague el interruptor de alimentacin de la copiadora y extraiga la tarjeta SD de la ranura SD 2.
14. Instale la tarjeta Java VM en la ranura SD 2.
15. Coloque la tapa de la ranura SD (
x 1).
Si se produce un error durante una descarga, aparecer un mensaje de error en la primera lnea. Los
cdigos de error tienen la letra E y un nmero (por ejemplo, "E20").
564
Significado
Solucin
20
No se puede correlacionar la
direccin lgica
21
No se puede acceder a la
memoria
22
23
Se ha producido un error al
iniciarse el programa de
actualizacin de la ROM
24
30
31
32
33
34
35
36
40
42
43
44
565
49
50
Fallo en la comprobacin de la
confirmacin electrnica
566
10. Copie la carpeta del proveedor de App2Me en la ruta especificada de la tarjeta VM. La ruta es:
"unidad_de_tarjeta_SD\ sdk\dsdk\dist\337051920"
11. Ponga la cara que tiene la etiqueta de la tarjeta SD hacia la parte trasera de la mquina y, a
continuacin, introdzcala lentamente en la ranura SD 2 (inferior) hasta que oiga un chasquido.
12. Coloque la tapa de la ranura SD (
x 1).
5
1. Retire la tapa de la ranura SD [A] para tarjetas SD (
x 1).
3. Gire la cara de la etiqueta de la tarjeta SD de la unidad de navegador de la ltima versin [A] hacia
la parte delantera de la mquina. Despus, empjela lentamente en la ranura 2 para tarjetas SD
hasta que oiga un clic.
4. Enchufe la mquina y encienda el interruptor de alimentacin.
5. Pulse la tecla "User Tools" (Herramientas de usuario).
Si la mquina tiene registrado un ajuste de administrador, los pasos 5 y 6 son obligatorios. En
caso contrario, contine en el paso 7.
568
x 1).
569
x 1).
3. Inserte la tarjeta SD que contiene los datos del idioma en la ranura 2 para tarjetas SD.
4. Encienda el interruptor principal de la copiadora. La pantalla inicial se abre despus de 45 segundos.
5. Pulse "Datos de idioma (2)" (Language Data) en la pantalla (o pulse
).
Qu hace
LANG. 1(1)
LANG. 1(2)
Salir (0)
7. Pulse "LANG 1(1)" para seleccionar el primer idioma. Pulse "LANG (2)" para seleccionar el segundo
idioma.
570
(7)" o "
571
Otra pantalla con una barra de progreso no muestra cuando el idioma se est descargando.
Durante la descarga del idioma ocurre lo siguiente:
El panel de operaciones se apaga.
El LED de la tecla de encendido parpadea rpidamente.
11. Despus de que haya aparecido el mensaje de instalacin finalizada en el LCD, apague el interruptor
principal de la copiadora. A continuacin, extraiga la tarjeta SD de la ranura.
12. Encienda el interruptor principal de la copiadora para volver a iniciar la operacin normal.
572
primero.
3. Cuando el mensaje le pida que confirme si desea restablecer los ajustes de sistema, pulse S.
4. Pulse Salir cuando el mensaje le indique que los ajustes ya se han restablecido.
573
primero.
3. Cuando el mensaje le pida que confirme si desea restablecer los ajustes de copiadora o Document
Server, pulse S.
4. Pulse Salir cuando el mensaje le indique que los ajustes ya se han restablecido.
574
575
576
577
5. No retire la tarjeta SD de su sitio [A] dentro de la tapa interna despus de copiar el programa de
aplicacin de una tarjeta a otra. Debe hacerlo por los motivos siguientes:
1) La tarjeta SD puede ser la nica prueba de que el usuario dispone de licencia para usar el
programa de aplicacin.
2) Puede necesitar comprobar la tarjeta SD y los datos que contiene para resolver un problema
en el futuro.
Mover ejecutables
El men Mover ejecutables (SP5-873-001) le permite copiar programas de aplicacin desde la tarjeta
SD original a otra tarjeta SD.
No ponga en ON el interruptor de proteccin contra escritura de la tarjeta SD de la aplicacin en
la mquina. Si el switch de proteccin contra escritura est en ON, se producir un error de descarga
(por ejemplo, Cdigo de error 44) durante la actualizacin del firmware o la fusin de aplicaciones.
1. Apague el interruptor principal.
2. Compruebe que hay una tarjeta SD en la ranura 1 para tarjetas SD. El programa de aplicacin se
copia en esta tarjeta SD.
3. Introduzca la tarjeta SD (que contiene el programa de aplicacin) en la ranura 2 para tarjetas SD.
El programa de aplicacin se copia desde esta tarjeta SD.
4. Encienda el interruptor principal.
5. Inicie el modo SP.
6. Seleccione SP5-873-001 Mover ejecutables.
7. Siga las instrucciones de los mensajes que aparecen en el panel de mandos.
8. Apague el interruptor principal.
578
Deshacer ejecutables
El men Deshacer ejecutables (SP5-873-002) le permite volver a copiar los programas de aplicacin
desde una tarjeta SD a la tarjeta SD original. Puede usar este programa, por ejemplo, cuando haya
copiado programas por error usando Mover ejecutables (SP5-873-001).
No ponga en ON el interruptor de proteccin contra escritura de la tarjeta SD de la aplicacin en
la mquina. Si el switch de proteccin contra escritura est en ON, se producir un error de descarga
(por ejemplo, Cdigo de error 44) durante la actualizacin del firmware o la fusin de aplicaciones.
1. Apague el interruptor principal.
2. Introduzca la tarjeta SD original en la ranura 2 para tarjetas SD. El programa de aplicacin volver
a copiarse en esta tarjeta.
3. Introduzca la tarjeta SD (que contiene el programa de aplicacin) en la ranura 1 para tarjetas SD.
El programa de aplicacin se copiar desde esta tarjeta SD.
4. Encienda el interruptor principal.
5. Inicie el modo SP.
6. Seleccione SP5-873-002 Deshacer ejecucin.
7. Siga las instrucciones de los mensajes que aparecen en el panel de mandos.
8. Apague el interruptor principal.
9. Retire la tarjeta SD de la Ranura 2.
En este paso se supone que el aparato utiliza los programas de aplicacin contenidos en la
tarjeta SD.
10. Encienda el interruptor principal.
11. Compruebe que los programas de aplicacin se ejecutan normalmente.
579
580
5. Ejecute SP 5824-001 (Carga de los datos de la NVRAM) y, a continuacin, pulse la tecla "Ejecutar".
6. Los siguientes archivos se copian en una carpeta de la NVRAM en la tarjeta SD una vez acabado
el procedimiento de carga. El archivo se guarda en la ruta de acceso y con el nombre de archivo
siguiente:
NVRAM\<nmero de serie>.NV
En el ejemplo siguiente, el nmero de serie es "K5000017114":
NVRAM\K5000017114.NV
7. A fin de evitar errores durante la descarga, compruebe que ha marcado la tarjeta SD que contiene
los datos cargados con el nmero del aparato desde el que se han cargado dichos datos.
Puede cargar los datos de la NVRAM desde ms de una mquina en la misma tarjeta SD.
581
582
Seleccionar ttulos
Carpeta
Autenticacin local
Autenticacin de carpeta
ACL de cuenta
ACL inicial nuevo documento
Autenticacin LDAP
Descarga
1. Prepare una tarjeta SD formateada.
2. Asegrese de que la proteccin contra escritura de la tarjeta SD est desactivada.
3. Apague el interruptor de alimentacin principal de la mquina.
4. Retire la tapa de la ranura de la tarjeta SD en la parte trasera izquierda de la mquina (
x 1).
Carga
1. Apague el interruptor de alimentacin principal de la mquina.
2. Retire la tapa de la ranura de la tarjeta SD en la parte trasera izquierda de la mquina (
x 1).
584
585
El ajuste predeterminado es "0" (Desactivado). Es necesario activar esta funcin para poder
guardar la informacin de depuracin.
4. Seleccione el destino en el que desee guardar la informacin de depuracin. Bajo "5857 Guardar
registro de depuracin, pulse "2 Destino", introduzca "2" con la tecla del panel de mandos para
seleccionar el disco duro como destino. Despus, pulse .
Seleccione "3 Tarjeta SD" para guardar la informacin de depuracin directamente en la tarjeta
SD si est insertada en la ranura de servicio.
5. Ahora pulse "5858" y especifique los eventos que desee guardar en el registro de depuracin.
SP5858 (Guardar depuracin cuando) incluye los siguientes elementos para su seleccin.
1
Cualquier Error SC
Atasco
586
Para obtener detalles sobre los nmeros de cdigos SC, consulte las tablas de SC en la seccin
4, "Deteccin de errores".
6. Seleccione uno o ms mdulos de memoria para leer y registrar informacin de depuracin. Pulse
"5859".
En 5859, pulse la tecla correspondiente al mdulo que desee registrar.
Introduzca el nmero de 4 dgitos apropiado. Despus, pulse
Consulte las dos tablas siguientes en las que encontrar los nmeros de 4 dgitos que debe
introducir para cada tecla.
El ejemplo siguiente muestra la "Key 1" con "2222".
587
Las siguientes teclas se pueden ajustar con los nmeros correspondientes. (Las iniciales en parntesis
indican los nombres de los mdulos).
Entradas de 4 dgitos para las teclas 1 a 10
N de tecla
Copia
Impresora
2222 (SCS)
14000 (SRM)
256 (IMH)
1000 (ECS)
1025 (MCS)
Escner
Web
4848 (COPIA)
4400 (GPS)
5375 (escaneo)
5682 (NFA)
2224 (BCU)
4500 (PDL)
5682 (NFA)
6600 (WebDB)
4600 (GPS-PM)
3000 (UCS)
3300 (PTS)
2000 (NCS)
2000 (NCS)
6666 (WebSys)
10
2224 (BCU)
4126 (DCS)
2000 (NCS)
588
Acrnimo
Significado
Acrnimo
ECS
GPS
Servicio de impresin GW
Lenguaje de diseo de
impresora
PDL
Significado
GSP-PM
PTS
Servidor de impresin
IMH
Controlador de memoria de
imagen
SCS
MCS
SRM
NCS
WebDB
1. Ahora, el aparato est configurado para registrar la informacin de depuracin de forma automtica
en el disco duro (el destino seleccionado con SP5857-002) para los eventos que haya seleccionado
con SP5858 y para los mdulos de memoria que haya seleccionado con SP5859.
Tenga en cuenta los siguientes puntos importantes cuando haga este ajuste:
Observe que las entradas numricas de las teclas 1 a 5 son iguales para los mdulos de memoria
de Copia, Impresora, Escner y Web.
Los valores iniciales son todos cero.
Esta configuracin se mantiene hasta que se cambia. Asegrese de comprobar todos los valores,
especialmente los de las teclas 6 a 10. Para desactivar la configuracin de una tecla, introduzca un
cero para esa tecla.
Puede seleccionar las teclas que desee de la 1 a la 10 (o todas ellas) introduciendo los nmeros de
4 dgitos correspondientes de la tabla.
No se puede mezclar la configuracin de los grupos (COPIA, IMPRESORA, etc.) para 006 a 010.
Por ejemplo, si desea crear un registro de depuracin de una IMPRESORA, debe seleccionar la
configuracin de las 9 selecciones disponibles para la columna "IMPRESORA" nicamente.
Hay un rea del disco reservada para almacenar el registro de depuracin. El tamao de este rea
se limita a 4 MB.
590
Procedimiento
1. Apague el interruptor de alimentacin principal.
2. Inserte la tarjeta SD en la ranura 2. A continuacin, encienda la alimentacin.
3. Entre en el modo SP.
4. Seleccione "SP de impresora".
5. Seleccione SP-1001 "Bit Switch.
591
6. Seleccione Configuracin de Bit Switch 1 y utilice el teclado numrico para encender el bit 4 y, a
continuacin, pulse el botn # para registrar el cambio. El resultado debe parecerse a:
00010000. La opcin Guardar tarjeta aparecer en el men "Lista de impresiones de prueba".
592
10. Card Save (Add) y Card Save (New) deben visualizarse en la pantalla. Seleccione Card Save (Add)
[Guardar tarjeta (Aadir)] o Card Save (New) [Guardar tarjeta (Nueva)].
14. Enve un trabajo a la impresora. La luz de comunicacin debe empezar a parpadear tal y como se
muestra a continuacin.
593
16. Pulse "Offline" (fuera de lnea) y, a continuacin, el botn "Borrar/Parar" para salir del modo
Guardar tarjeta.
17. Restablezca la configuracin de bit switch a la predeterminada 00000000. Pulse el botn # del
teclado numrico para registrar los cambios.
18. Retire la tarjeta SD una vez que se apague el interruptor de alimentacin principal.
Mensajes de error
Mensajes de error de Guardar tarjeta:
Error de inic.: no se pudo inicializar un proceso de almacenamiento (por ejemplo, deteccin de
tarjeta, cambio a modo de kernel).
No se encontr la tarjeta: no se pudo detectar la tarjeta en la ranura.
Sin memoria: memoria de trabajo insuficiente para procesar el trabajo.
Error de escritura: error al escribir en la tarjeta.
594
595
596
6. Localizacin de averas
Tablas de SC
Condiciones de llamada al servicio tcnico
Resumen
La seccin Tabla de SC muestras los cdigos de SC para los errores del controlador y otros errores. Los
ltimos (los errores que no son del controlador) se clasifican en cuatro tipos. El tipo viene determinado por
sus procedimientos para restablecerlos. La tabla muestra la clasificacin de los cdigos de SC.
Clave
Errores del
controlador
Otros errores
Definicin
Procedimiento de restauracin
Se produjo un error en el
controlador.
El funcionamiento de la mquina
est desactivado. Puede reiniciar la
mquina apagando y encendiendo
el interruptor principal o el
interruptor de funcionamiento. Si el
error se produce otra vez, se
visualiza el mismo cdigo de SC.
CTL
6. Localizacin de averas
Los datos del registro de impresin (SP5-990-004) en el modo SP pueden comprobar los ltimos 10
cdigos SC detectados y los contadores totales cuando se detecte el cdigo de SC.
Si el problema afecta a las placas de circuitos elctricos, en primer lugar, desconecte y vuelva a
conectar los conectores antes de cambiar las placas de circuito impreso.
Si el problema est relacionado con un bloqueo del motor, en primer lugar, compruebe la carga
mecnica antes de cambiar motores o sensores.
1XX
2XX
3XX
598
Seccin
Escaneo
Exposicin al lser
Revelado de imagen 1
Cdigo de
SC
Seccin detallada
100 -
Escner
190 -
200 -
Motor poligonal
220 -
Control de sincronizacin
230 -
240 -
Control de LD
280 -
300 -
Carga
330 -
350 -
Revelado
380 -
Tablas de SC
Clase 1
4XX
5XX
5XX
6XX
7XX
Seccin
Revelado de imagen 2
Comunicacin
Perifricos
Cdigo de
SC
Seccin detallada
400 -
Transferencia de imgenes
420 -
430 -
Limpieza
440 -
460 -
Unidad
480 -
Otros
500 -
515 -
Dplex
520 -
530 -
540 -
Fusin
560 -
Otros
570 -
600 -
Contadores elctricos
620 -
Contadores mecnicos
630 -
Control de cuenta
640 -
CSS
650 -
Red
670 -
680 -
700 -
720 -
740 -
Finisher de folletos
599
6. Localizacin de averas
Clase 1
Seccin
8XX
Controlador
9XX
Otros
Cdigo de
SC
Seccin detallada
800 -
820 -
Error de diagnstico
860 -
Disco duro
880 -
900 -
Contador
920 -
Memoria
990 -
Otros
SC1xx: Escaneado
N.
Tipo
101
600
Tablas de SC
N.
Tipo
120
N.
Tipo
121
601
6. Localizacin de averas
N.
Tipo
141
N.
Tipo
602
Tablas de SC
N.
Tipo
144
N.
161
Tipo
D
-002
603
6. Localizacin de averas
N.
Tipo
165
N.
Tipo
604
Tablas de SC
SC 2xx: Exposicin
N.
Tipo
202
N.
Tipo
203
605
6. Localizacin de averas
N.
Tipo
204
N.
Tipo
220
222
LDB defectuosa
BCU defectuosa
1. Compruebe los conectores.
2. Sustituya la unidad lser.
3. Cambie la placa IPU.
4. Sustituya la BCU.
606
Tablas de SC
N.
Tipo
230
ASIC defectuoso
Conexin deficiente entre la IPU y la BCU.
BCU defectuosa
1. Compruebe la conexin entre la placa del controlador y la BCU.
2. Sustituya la BCU.
3. Sustituya la placa del controlador.
N.
Tipo
231
N.
Tipo
232
607
6. Localizacin de averas
N.
Tipo
233
N.
Tipo
234
N.
Tipo
235
N.
Tipo
236
608
Tablas de SC
N.
Tipo
237
N.
Tipo
240
Error de LD: K
241
Error de LD: Y
La BCU detecta un error de LDB varias veces de forma consecutiva cuando se
enciende la unidad LDB y tras la inicializacin del LDB.
LD gastado
609
6. Localizacin de averas
N.
Tipo
285
610
Tipo
312
313
314
315
Tablas de SC
N.
Tipo
N.
Tipo
325
N.
Tipo
360
361
362
363
611
6. Localizacin de averas
N.
Tipo
4. Sustituya la PCDU.
N.
Tipo
364
365
366
367
Sensor TD defectuoso
1. Compruebe el conector del sensor TD negro, magenta, cian o amarillo y el
mazo de cables entre el sensor TD y la unidad de revelado en busca de daos.
2. Compruebe el conector del cajn de la PCDU.
3. Cambie la unidad de revelado.
4. Sustituya la PCDU.
612
Tablas de SC
N.
Tipo
372
373
374
375
Sensor TD defectuoso
Mazo de cables entre el sensor TD y el cajn desconectado, defectuoso
Densidad de revelador diferente respecto a la densidad de revelador inicial
1. Retire la junta trmica de cada PCDU.
2. Cambie la unidad de revelado.
3. Sustituya la PCDU.
N.
Tipo
380
381
LoL
613
6. Localizacin de averas
N.
Tipo
396
Tipo
397
614
Tablas de SC
Tipo
400
615
6. Localizacin de averas
N.
Tipo
441
616
Tablas de SC
N.
Tipo
442
Funcionamiento:
1. Compruebe la conexin del mazo de cables del sensor de contacto de la ITB.
2. Sustituya el sensor de contacto de la ITB.
617
6. Localizacin de averas
N.
Tipo
443
Tipo
452
618
Tablas de SC
N.
Tipo
491
N.
Tipo
Se detecta una seal de error durante 0,2 segundos cuando se carga la separacin,
banda de transferencia de imagen o el rodillo de transferencia de papel.
Fuga de alta tensin
Mazo de cables roto
Unidad de banda de transferencia de imagen o unidad de transferencia de
papel defectuosa
492
619
6. Localizacin de averas
N.
Tipo
495
620
Tipo
503
504
Tablas de SC
N.
Tipo
Tipo
506
621
6. Localizacin de averas
N.
Tipo
508
622
Tipo
530
531
Tablas de SC
N.
Tipo
N.
Tipo
623
6. Localizacin de averas
N.
Tipo
533
DRB defectuoso
BCU defectuosa
1. Compruebe o sustituya el mazo de cables.
2. Sustituya el ventilador delantero de fusin.
3. Cambie el DRB.
4. Sustituya la BCU.
N.
Tipo
534
DRB defectuoso
BCU defectuosa
1. Compruebe o sustituya el mazo de cables.
2. Sustituya el ventilador posterior de fusin.
3. Cambie el DRB.
4. Sustituya la BCU.
624
Tablas de SC
N.
Tipo
535
N.
Tipo
625
6. Localizacin de averas
N.
Tipo
540
N.
Tipo
N.
Tipo
542
626
Tablas de SC
N.
Tipo
N.
Tipo
543
PSU defectuosa
BCU defectuosa
1. Cambie la PSU
2. Sustituya la BCU.
627
6. Localizacin de averas
N.
Tipo
544
PSU defectuosa
BCU defectuosa
Sistema de control de fusin defectuoso
1. Cambie la PSU
2. Sustituya la BCU.
N.
Tipo
6
545
628
Tablas de SC
N.
Tipo
547
3. Sustitucin de la PSU
N.
Tipo
551
629
6. Localizacin de averas
N.
Tipo
552
Tipo
553
PSU defectuosa
BCU defectuosa
1. Cambie la PSU
2. Sustituya la BCU.
630
Tablas de SC
N.
Tipo
554
BCU defectuosa
Sistema de control de fusin defectuoso
1. Cambie la PSU
2. Sustituya la BCU.
N.
Tipo
555
N.
Tipo
557
631
6. Localizacin de averas
N.
Tipo
559
N.
Tipo
N.
Tipo
563
PSU defectuosa
BCU defectuosa
1. Cambie la PSU
2. Sustituya la BCU.
632
Tablas de SC
N.
Tipo
564
BCU defectuosa
Sistema de control de fusin defectuoso
1. Cambie la PSU
2. Sustituya la BCU.
N.
Tipo
571
N.
Tipo
573
PSU defectuosa
BCU defectuosa
1. Cambie la PSU
2. Sustituya la BCU.
633
6. Localizacin de averas
N.
Tipo
574
BCU defectuosa
Sistema de control de fusin defectuoso
1. Cambie la PSU
2. Sustituya la BCU.
Tipo
610
611
634
Tablas de SC
N.
Tipo
620
IPU defectuosa
Ruido externo
1. Compruebe la conexin de cables del ARDF.
2. Elimine el ruido externo.
3. Sustituya el ARDF.
4. Cambie la IPU.
N.
Tipo
621
Problemas de la BCU
Problemas de la PSU en la mquina
Problemas de la placa principal en los perifricos
Placa principal de perifricos defectuosa.
Perifricos desconectados.
1. Compruebe si los cables de los perifricos estn conectados correctamente.
2. Sustituya la PSU si no se suministra alimentacin a los perifricos.
3. Sustituya la placa principal de perifricos.
4. Sustituya la BCU.
635
6. Localizacin de averas
N.
Tipo
632
CTL
B
N.
Tipo
633
CTL
B
N.
Tipo
634
CTL
B
N.
Tipo
635
CTL
B
636
Tablas de SC
N.
636
Tipo
CTL
01
02
N.
Tipo
641
CTL
D
637
6. Localizacin de averas
N.
Tipo
CTL
650
-001
-005
638
Tablas de SC
N.
Tipo
651
CTL
C
N.
Tipo
669
Tipo
670
CTL
D
N.
Tipo
639
6. Localizacin de averas
CTL
D
N.
Tipo
6
672
CTL
D
N.
681
640
Tipo
D
Tablas de SC
N.
Tipo
001-005
061-164
Ruido
1. Cambie el cartucho de tner.
2. Apague y encienda la mquina.
3. Sustituya la placa del controlador RFID-R/W.
N.
Tipo
682
641
6. Localizacin de averas
N.
Tipo
683
N.
Tipo
BCU defectuosa
Controlador defectuoso
1. Compruebe si el controlador est firmemente conectado a la BCU.
2. Actualice el firmware de la IPU.
3. Sustituya el disco duro.
4. Actualice el firmware de la BCU.
5. Sustituya la BCU.
6. Sustituya la placa del controlador.
642
Tablas de SC
N.
Tipo
690
Conexin suelta
BCU defectuosa
Placa del controlador LD defectuoso
1. Apague y encienda el interruptor principal.
2. Compruebe la conexin de cable.
3. Sustituya la unidad lser.
4. Sustituya la placa BCU.
SC7xx: Perifricos
N.
Tipo
730
643
6. Localizacin de averas
N.
Tipo
740
N.
Tipo
742
644
Tablas de SC
N.
Tipo
750
N.
Tipo
645
6. Localizacin de averas
N.
Tipo
763
N.
Tipo
Conector defectuoso
Sensor de deteccin del borde del papel defectuoso.
Conversor de AD o DA defectuoso.
1. Sustituya la unidad del deslizador de perforacin.
2. Sustituya la unidad de perforacin.
N.
646
Tipo
788
Finisher: Error del sensor de tamao del papel sin bandeja lateral
789
Tablas de SC
N.
Tipo
N.
Tipo
790
Finisher: Error del motor del emparejador delantero sin bandeja lateral
793
Finisher: Error del motor del emparejador delantero con bandeja lateral
La mquina no detecta una seal correcta procedente del sensor de posicin inicial
del tope del emparejador delantero en el encendido. El primer fallo de deteccin
emite un error de atasco, y el segundo fallo emite este cdigo SC.
Tipo
791
Finisher: Error del motor del emparejador trasero sin bandeja lateral
794
Finisher: Error del motor del emparejador trasero con bandeja lateral
647
6. Localizacin de averas
N.
Tipo
N.
Tipo
792
Error del motor de contacto del rodillo de captacin sin bandeja lateral
795
Error del motor de contacto del rodillo de captacin con bandeja lateral
La mquina no detecta una seal correcta procedente del sensor de posicin inicial
del rodillo de captacin en el encendido. El primer fallo de deteccin emite un error
de atasco, y el segundo fallo emite este cdigo SC.
Motor de contacto del rodillo de captacin defectuoso
Conexin suelta
Sobrecarga del motor
Sensor de posicin inicial del rodillo de captacin defectuoso
1. Sustituya el motor de contacto de captacin.
2. Sustituya el sensor de posicin inicial del rodillo de admisin
648
Tablas de SC
N.
Tipo
796
N.
Tipo
797
Tipo
798
649
6. Localizacin de averas
N.
Tipo
799
Tipo
816
CTL
D
N.
Tipo
817
CTL
D
N.
Tipo
819
650
CTL
C
Tablas de SC
N.
Tipo
[0x5032]
[0x696e]
inic cancelada
[0x766d]
vm_pageout: VM llena
[554C]
Error USB
N.
820
Tipo
CTL
D
[0001] a [06FF]
[0801] a [4005]
651
6. Localizacin de averas
N.
Tipo
[0702]
RAM-DIMM defectuoso
[0709]
Controlador defectuoso
[070A]
N.
821
Tipo
CTL
D
[0B00]
[0B06]
ASIC defectuoso
Interfaces de North Bridge y PCI defectuosos
Sustituya la placa del controlador.
652
Tablas de SC
N.
Tipo
[0D05]
RAM-DIMM defectuoso
Controlador defectuoso
1. Instale de nuevo el firmware del sistema del controlador.
2. Sustituya el RAM-DIMM.
3. Sustituya la placa del controlador.
Error del dispositivo de puente de vdeo (ASIC) 1
La CPU no detecta el dispositivo de puente de vdeo.
[50A1]
[50A2]
Tipo
CTL
822
[3003]
[3004]
Error de comando.
653
6. Localizacin de averas
N.
Tipo
N.
823
Tipo
CTL
B
[6101]
[6104]
654
[6105]
Sustituya el controlador.
Tablas de SC
N.
Tipo
824
CTL
D
Conexin suelta
NVRAM estndar defectuosa
Controlador defectuoso
1. Compruebe que la NVRAM estndar est firmemente instalada en el zcalo.
2. Sustituya la NVRAM.
3. Sustituya la placa del controlador.
N.
826
Tipo
CTL
D
[1501]
[15FF]
N.
827
Tipo
CTL
D
655
6. Localizacin de averas
N.
Tipo
[0201]
[0202]
N.
828
Tipo
CTL
D
[0101]
N.
829
656
Tipo
CTL
B
Tablas de SC
N.
Tipo
[0401]
N.
833
Tipo
CTL
C
[0F30]
[0F31]
Sustituya la BCU.
No se ha podido detectar ASIC (Mandolin) para el control de sistema.
Despus de la configuracin de PCI, no se ha podido comprobar el ID de
dispositivo del ASIC.
[0F41]
Sustituya la BCU.
No pudo inicializar o leer la conexin bus.
[50B1]
[50B2]
N.
838
Tipo
CTL
D
657
6. Localizacin de averas
N.
Tipo
[2701]
Tipo
CTL
C
[9101]
[9110]
N.
Tipo
851
CTL
B
IEEE1394 defectuoso
Controlador defectuoso
1. Apague y encienda el interruptor principal.
2. Sustituya la placa de interface IEEE1394.
3. Sustituya el controlador.
658
Tablas de SC
N.
Tipo
853
CTL
B
N.
Tipo
854
CTL
B
N.
Tipo
855
CTL
856
Conexin suelta
Tarjeta de red LAN inalmbrica/Bluetooth defectuosa
1. Compruebe la conexin.
2. Sustituya la tarjeta de red LAN inalmbrica/Bluetooth.
N.
Tipo
857
CTL
B
6. Localizacin de averas
N.
Tipo
[1]
858
CTL
[30]
[30]
660
Tablas de SC
N.
Tipo
859
CTL
N.
Tipo
860
CTL
B
661
6. Localizacin de averas
N.
Tipo
861
CTL
D
Cables defectuosos
Disco duro defectuoso
Controlador defectuoso
1. Compruebe la conexin entre la HDD y el controlador
2. Compruebe y sustituya los cables.
3. Sustituya el disco duro.
4. Sustituya el controlador.
N.
Tipo
862
CTL
D
N.
Tipo
863
CTL
Controlador defectuoso
1. Sustituya el disco duro.
2. Sustituya el controlador.
662
Tablas de SC
N.
Tipo
864
CTL
D
N.
Tipo
865
CTL
D
N.
Tipo
866
CTL
B
N.
Tipo
867
CTL
D
663
6. Localizacin de averas
N.
Tipo
868
CTL
D
N.
Tipo
870
CTL
B
664
Tablas de SC
N.
Tipo
872
CTL
B
N.
Tipo
873
CTL
B
N.
Tipo
874
CTL
D
665
6. Localizacin de averas
N.
Tipo
875
CTL
D
Se detecta un error al dar formato lgico a todo el disco duro o la NVRAM a travs
de la unidad DataOverwriteSecurity.
El formato lgico del disco duro falla.
Apague y encienda el interruptor principal e intente de nuevo la operacin.
N.
Tipo
876
CTL
D
-001
-002
-003
-004
666
Tablas de SC
N.
Tipo
-005
-099
N.
Tipo
877
CTL
D
N.
Tipo
878
CTL
D
667
6. Localizacin de averas
N.
Tipo
880
CTL
D
SC9xx: Varios
N.
Tipo
900
CTL
D
NVRAM defectuosa
Controlador defectuoso
1. Compruebe la conexin entre la NVRAM y el controlador.
2. Sustituya la NVRAM.
3. Sustituya el controlador.
N.
Tipo
920
CTL
D
Software defectuoso
Recurso de hardware inesperado (por ejemplo, escasez de memoria)
1. Software defectuoso; apague y encienda o cambie el firmware del
controlador si no se resuelve el problema.
2. Memoria insuficiente
668
Tablas de SC
N.
Tipo
921
CTL
D
N.
Tipo
990
CTL
D
Controlador defectuoso
Error de software
Tipo
991
CTL
C
669
6. Localizacin de averas
N.
Tipo
992
CTL
D
N.
995
Tipo
D
-001
-002
-003
Controlador defectuoso
Cambie la placa del controlador con el tipo correcto.
-004
670
Tablas de SC
N.
Tipo
997
CTL
B
N.
Tipo
998
CTL
D
Problema de software
1. Compruebe la configuracin de SP5875-001. Si est configurado en "1
(OFF)", cmbielo a "0 (OFF)".
2. Compruebe si el DIMM RAM y el DIMM ROM estn conectados
correctamente.
3. Instale de nuevo el firmware del sistema del controlador.
4. Sustituya el controlador.
Nota 1
Si un problema se repite siempre en una condicin especfica (por ejemplo, configuracin del driver de
impresora, archivo de imagen), es posible que la causa del problema sea un error de software. En este
671
6. Localizacin de averas
caso, deber enviar al especialista de producto los datos y la informacin siguientes. Debe tener en cuenta
que puede tardar algn tiempo en obtener una respuesta indicndole cmo resolver el problema, porque
en algunos casos es necesario que los datos sean analizados por el personal de diseo en Japn.
Sntoma / causas posibles / medidas adoptadas
Hoja de resumen (Modo SP Printer SP, SP1-004 [Print Summary])
SMC - Todos (SP5-990-001)
SMC - Registro (SP5-990-004)
Configuraciones del driver de impresora utilizadas cuando ocurri el problema
Todos los datos que se muestran en la pantalla (cdigo SC, cdigo de error y direccin de programa
donde se registr el problema).
Archivo de imagen que causa el problema, si es posible
672
Resultado
Finalizado con
xito
Descripcin
Inicializacin del
revelador finalizada con
xito.
Causas posibles/Accin
Se abri una tapa o se apag el interruptor
principal durante la inicializacin.
Terminacin
forzada
La inicializacin del
revelador termin a la
fuerza.
Error Vt
Vt es inferior a 0,7V
cuando Vcnt es 4,3V.
Error Vcnt 1
Error Vcnt 2
Vt es inferior a 0,7 V
cuando Vcnt es 4,3 V y
Vcnt es superior a 4,7 V
cuando Vcnt tiene el valor
objetivo de Vt 0,2 V.
1. Sensor de TD defectuoso
1. Sensor de TD defectuoso
2. Los ajustes de objetivo de Vt no son
correctos.
3. Error de densidad del tner
1. Sensor de TD defectuoso
673
6. Localizacin de averas
N.
Resultado
Error Vcnt 3
Descripcin
Causas posibles/Accin
1. Sensor de TD defectuoso
La mquina inicia la inicializacin del revelador despus de que ajuste 1 en SP3-902-005, 006,
007, o 008. La inicializacin del revelador vuelve a empezar automticamente cuando abre y cierra
la puerta delantera o apaga y enciende el interruptor principal o si se produce un error que no sea
el Error 8.
El nmero que se visualiza muestra los resultados de cada autocomprobacin de control de proceso.
00000000 = YYMMCCKK
SP3-012-001 a -010 (Resultado de la autocomprobacin del control del proceso)
N.
Resultado
Descripcin
Causas posibles/Accin
11
Finalizado con
xito
Autocomprobacin del
control del proceso
finalizada con xito.
41
Error Vt
Se detecta error de Vt
mximo o mnimo.
674
N.
Resultado
Descripcin
Causas posibles/Accin
La imagen slida no tiene densidad
suficiente:
1. Reintente el control de proceso.
2. Sustituya los sensores de la ID.
53
Error de
deteccin del
coeficiente del
sensor ID (K5)
54
55
Error mximo/
mnimo del
coeficiente del
sensor ID (K5)
Error gamma:
Mximo
Cuando el K5 sea ms
que el valor de
SP3-362-003 o menos
que el valor de
SP3-362-004, se
visualiza el error 54.
56
Error gamma:
Mnimo
57
Error Vk:
Mximo
300 < Vk
Hardware defectuoso.
Igual que 53
675
6. Localizacin de averas
N.
58
Resultado
Descripcin
Causas posibles/Accin
59
99
Error de datos de
No se pueden muestrear
muestreo
suficientes datos durante
durante la
la correccin gamma.
correccin gama
Error inesperado
676
N.
Resultado
Descripcin
Causas posibles/Accin
Correcto
El ajuste Vsg se
realiz
correctamente.
N.
Resultado
Descripcin
Causas posibles/Accin
Sensores ID sucios (tner, polvo o materias extraas)
Cinta de transferencia de imagen sucia
Cinta de transferencia de imagen rayada
Sensores ID defectuosos
Conexin defectuosa
Vsg no se puede
Error del ajuste
ajustar dentro de
del sensor ID
4,0 0,5V.
BCU defectuosa
1. Limpie los sensores ID.
2. Compruebe la unidad de limpieza de la ITB. Limpie
o cambie la banda de transferencia de imagen.
3. Sustituya la banda de transferencia de imagen.
4. Sustituya los sensores de la ID.
5. Compruebe la conexin.
6. Sustituya la placa BCU.
Sensores ID defectuosos
La salida del sensor
ID es superior al
Error de salida
"Umbral
del sensor ID
Voffset" (SP3-324004)
Conexin defectuosa
BCU defectuosa
1. Sustituya los sensores de la ID.
2. Compruebe la conexin.
3. Sustituya la placa BCU.
Otros casos
Vuelva a intentar SP3-321-010.
Resultado
Descripcin
Nota
No se hace
Completado
correctamente
677
6. Localizacin de averas
N.
Resultado
Descripcin
No se pueden
detectar las tramas
Menos lneas en la
trama que en el
objetivo
Ver Nota
Hay ms lneas en
la trama que en el
objetivo
No se utiliza
5-9
Nota
Para obtener ms detalles, consulte la "Gua de solucin de problemas - Ajuste de posicin de lnea".
678
679
6. Localizacin de averas
680
Prueba
1. Ejecute SP2-111-003 (Modo c: ajuste aproximado).
2. Utilice SP2-194-007 para comprobar si el resultado del ajuste de posicin de lnea es correcto (0:
Finalizado con xito, 1: No finalizado). Si el resultado es "1", consulte Lista de contramedidas para
los errores de registro de color.
3. Ejecute SP2-111-001 (Modo a: ajuste fino dos veces).
4. Utilice SP2-194-007 para comprobar si el resultado del ajuste de posicin de lnea es correcto (0:
Finalizado con xito, 1: No finalizado). Si el resultado es "1", consulte Lista de contramedidas para
los errores de registro de color.
681
6. Localizacin de averas
Posible causa/Contramedida
Unidad de procesamiento de imagen defectuosa
Trama de prueba con baja densidad
Controlador defectuoso
1. Cambie la fuente de alimentacin de alta tensin.
2. Ejecute el control de proceso forzado (SP3-011-001) o
suministre algo de tner (SP3-015-xxx).
3. Sustituya la BCU.
Sensores ID defectuosos
BCU defectuosa
1. Sustituya el sensor ID.
2. Sustituya la BCU.
Posible causa/Contramedida
Unidad lser defectuosa
BCU defectuosa
1. Sustituya la unidad lser.
2. Sustituya la BCU.
Banda de transferencia de imagen defectuosa
682
Posible causa/Contramedida
Sensor ID defectuoso en el centro
La inclinacin de M, C, Y es superior a
0,75 mm respecto al registro de
escaneo principal de K
BCU defectuosa
1. Reinstale o cambie la BCU.
2. Sustituya la unidad lser.
3. Sustituya la BCU.
Posible causa/Contramedida
Ejecute SP2-111-001 o -002.
683
6. Localizacin de averas
Posible causa/Contramedida
Baja densidad
Sensor ID defectuoso
BCU defectuosa
1. Sustituya el sensor ID.
2. Sustituya la BCU.
Posible causa/Contramedida
Densidad de trama baja
Ejecute el control de proceso forzado (SP3-011-001) o
suministre algo de tner (SP3-015-xxx).
Componente no defectuoso
Unidad de alojamiento de la ptica lser defectuosa
BCU defectuosa
1. Ejecute SP2-111-003 otra vez.
2. Sustituya la unidad lser.
3. Sustituya la BCU.
684
Posible causa/Contramedida
Componente no defectuoso
Banda de transferencia de imagen defectuosa
Unidades de accionamiento defectuosas
BCU defectuosa
1. Ejecute SP2-111-003 otra vez.
2. Sustituya la banda de transferencia de imagen.
3. Sustituya el motor del tambor.
4. Sustituya la BCU.
3. Sustituya la BCU.
La inclinacin de M, C, Y es superior a
0,75 mm respecto al registro de
escaneo principal de K. al final de la
lnea de escaneo?
PCDU defectuosa
Unidad lser defectuosa
BCU defectuosa
1. Reinstale o cambie la PCDU.
2. Sustituya la unidad lser.
3. Sustituya la BCU.
Otros
685
6. Localizacin de averas
Posible causa/Contramedida
Posible causa/Contramedida
Densidad de trama baja
Ejecute el control de proceso forzado (SP3-011-001) o
suministre algo de tner (SP3-015-xxx).
686
Posible causa/Contramedida
Banda de transferencia de imagen defectuosa
Unidades de accionamiento defectuosas
Sensor ID defectuoso
BCU defectuosa
Valor SP incorrecto
1. Sustituya la banda de transferencia de imagen.
2. Sustituya el sensor ID.
3. Sustituya el motor del tambor.
4. Sustituya la BCU.
5. Ajuste el valor con SP2-182-022 en -039.
La inclinacin de M, C, Y es diferente.
PCDU defectuosa
Unidad de alojamiento de la ptica lser defectuosa
BCU defectuosa
1. Reinstale o cambie la PCDU.
PCDU defectuosa
Unidad de accionamiento defectuosa
Error de ajuste fase tambor
1. Ejecute SP1-902-001 (Ajuste de fase tambor); consulte
Cambio y ajuste Unidad de accionamiento Unidad
de engranajes, para obtener detalles.
2. Reinstale o cambie la PCDU.
3. Compruebe o sustituya la unidad de accionamiento.
687
6. Localizacin de averas
Rodillo de revelado: 32 mm
PTR (Rodillo de transferencia del papel): 75,0 mm
Tambor: 94,2 mm
Banda de fusin: 157,1 mm
688
Si uno de los ajustes de SP1-803-004 a 006 es "1" (error), vuelva al paso 1 e introduzca un
valor que sea ms cercano a "0" en comparacin con el valor introducido previamente.
Por ejemplo, si se introduce "+0,9" en los ajustes de SP1-803-001 a 003 y se produce un error,
introduzca "+0,8" o menos con SP1-803-001 a 003.
Por ejemplo, si se introduce "-0,9" en los ajustes de SP1-803-001 a 003 y se produce un error,
introduzca "-0,8" o ms con SP1-803-001 a 003.
Si se sigue produciendo un error, consulte "Ajuste de la velocidad del motor".
4. Ejecute el ajuste de la posicin de lnea (grueso) con SP2-111-003.
5. Ejecute el ajuste de la posicin de lnea (fino) con SP2-111-001.
6. Realice copias de muestra y compruebe si las impresiones son satisfactorias.
Mx.
Mn.
Ttulo
SP1-801-002
-4
SP1-801-003
-4
SP1-801-007
-6
SP1-801-009
-4
SP1-801-012
-2
SP1-801-014
-2
689
6. Localizacin de averas
N. de SP
Mx.
Mn.
Ttulo
SP1-801-016
-2
SP1-801-018
-2
SP1-801-020
-2
SP1-801-022
-2
Inversor:CW120 (0 predeterminado)
SP1-801-024
-2
Inversor:CCW120 (0 predeterminado)
SP1-801-026
-2
SP1-801-028
-2
690
Mx.
Mn.
Ttulo
SP1-801-025
-2
Entrada dplex:60
SP1-801-027
-2
Salida dplex:60
SP1-801-033
-4
SP1-801-034
-2
Alimentacin1:CW60:1200 dpi
SP1-801-035
-2
Alimentacin1:CCW60:1200 dpi
SP1-801-036
-2
Alimentacin2:CW60:1200 dpi
SP1-801-037
-2
Alimentacin2:CCW60:1200 dpi
SP1-801-038
-2
Bypass:60:1200 dpi
SP1-801-039
-2
Inversor:CW60:1200 dpi
SP1-801-040
-2
Inversor:CCW60:1200 dpi
N. de SP
Mx.
Mn.
Ttulo
SP1-801-041
-6
SP1-801-042
-4
BkOpcDevMot:60:1200 dpi
SP1-801-043
-4
Mx.
Mn.
Ttulo
SP1-801-001
-4
Mot regist:60:Grueso
SP1-801-004
-4
Bk OpcDevMot:60:Grueso
SP1-801-008
-6
Mot fusin:60:Grueso
SP1-801-010
-4
Mot transferencia:60:Grueso
SP1-801-011
-2
Alimentacin1:CW60:Grueso
SP1-801-013
-2
Alimentacin1:CCW60:Grueso
SP1-801-015
-2
Alimentacin2:CW60:Grueso
SP1-801-017
-2
Alimentacin2:CCW60:Grueso
SP1-801-019
-2
Bypass:60:Grueso
SP1-801-021
-2
Inversor:CW60:Grueso
SP1-801-023
-2
Inversor:CCW60:Grueso
691
6. Localizacin de averas
Pg.251)
Pg.179)
Pg.179)
Pg.172)
Pg.178)
x 3,
x 1,
x 2).
693
6. Localizacin de averas
5. Si las lneas horizontales se inclinan hacia abajo y hacia la izquierda [A], mueva la gua de fusin
delantera hacia arriba. Para hacerlo, gire la palanca del ajustador [B] de la gua delantera de fusin
en el sentido de las agujas del reloj [C].
6. Si las lneas horizontales se mueven hacia abajo y hacia la derecha [A], mueva la gua delantera
de fusin hacia abajo. Para hacerlo, gire la palanca del ajustador [B] de la gua de fusin delantera
en sentido contrario a las agujas del reloj [C].
Un incremento de la palanca del ajustador mueva la gua de fusin delantera 1 mm.
7. Vuelva a apretar los cuatro tornillos de la gua de fusin delantera.
8. Imprima el patrn de prueba y compruebe la calidad de imagen.
9. Si el sntoma persiste, repita los pasos anteriores.
694
Procedimiento de sustitucin
x 2).
695
6. Localizacin de averas
2. Deslice la tapa superior [A] de la unidad del tambor como se muestra y retrela.
6
3. Levante con cuidado la placa metlica [A] y retire el resorte [B] en el lado delantero y el lado trasero.
Tenga cuidado de no doblar la placa metlica.
696
Imagen granulada
Si se informa de imgenes granuladas desde el campo, utilice el siguiente diagrama de flujo para tomar
medidas en respuesta a las ocho condiciones.
697
6. Localizacin de averas
698
Procedimiento a adoptar
1. Si las imgenes granuladas solamente aparecen en reas de imagen en negro con el modo
Impresora a pleno color, seleccione "CMY+K" con el driver de la impresora PCL. Para obtener
detalles, consulte "Accin 1" que se describe a continuacin.
2. Cambie la polarizacin de transferencia de papel. Para obtener detalles, consulte "Accin 2A"
que se describe a continuacin.
3. Aumente la cantidad de tner por rea (M/A). Para ms detalles, consulte la "Accin 3" que se
describe a continuacin.
4. Pida al cliente que cambie el papel de un papel muy resistente a otro ms suave.
Causa 2: Imagen granulada en papel hmedo
La resistencia de la superficie del papel como papel hmedo es baja, y el campo elctrico para la
transferencia de papel es dbil.
Procedimiento a adoptar
1. Pida al cliente que conserve el papel en estado seco.
2. Encienda el calentador de la bandeja si ya se ha instalado o pida al cliente que instale el calentador
de bandeja opcional.
3. Si las imgenes granuladas solamente aparecen en reas de imagen en negro con el modo
Impresora a pleno color, seleccione "CMY+K" con el driver de la impresora PCL. Para obtener
detalles, consulte "Accin 1" que se describe a continuacin.
4. Cambie la polarizacin de transferencia de papel. Para obtener detalles, consulte "Accin 2A"
que se describe a continuacin.
5. Aumente la cantidad de tner por rea (M/A). Para ms detalles, consulte la "Accin 3" que se
describe a continuacin.
Causa 3: Imagen granulada en la 2 cara del papel
Puede estar causado por la diferencia de valor de resistencia de la 1 y la 2 cara del papel. La
resistencia de la 2 cara del papel cambia despus de que el papel ha pasado por la unidad de fusin.
Como resultado, la resistencia de la 2 cara del papel, que ha pasado por la unidad de fusin, est
fuera del intervalo de la resistencia estndar de papel.
699
6. Localizacin de averas
Procedimiento a adoptar
1. Si las imgenes granuladas solamente aparecen en reas de imagen en negro con el modo
Impresora a pleno color, seleccione "CMY+K" con el driver de la impresora PCL. Para obtener
detalles, consulte "Accin 1" que se describe a continuacin.
2. Cambie la polarizacin de transferencia de papel. Para obtener detalles, consulte "Accin 2B"
que se describe a continuacin.
3. Aumente la cantidad de tner por rea (M/A). Para ms detalles, consulte la "Accin 3" que se
describe a continuacin.
4. Pida al cliente que cambie el papel de un papel de superficie rugosa a uno ms suave.
Causa 4: Imagen granulada en papel de tamao pequeo
La corriente de transferencia tiende a debilitarse en el rea sin papel del rodillo de transferencia de
papel. Como resultado, la corriente de transferencia insuficiente provoca una imagen granulada al
utilizar un papel de tamao pequeo a temperatura elevada y en condiciones de humedad elevada.
Procedimiento a adoptar
1. Si las imgenes granuladas solamente aparecen en reas de imagen en negro con el modo
Impresora a pleno color, seleccione "CMY+K" con el driver de la impresora PCL. Para obtener
detalles, consulte "Accin 1" que se describe a continuacin.
2. Utilice el papel A4 LEF. Si el papel A4 LEF no soluciona la imagen granulada, compruebe las otras
causas (Causa 1, 2 y 3)
3. Cambie el coeficiente de correccin del tamao del papel. Para obtener detalles, consulte "Accin
4" que se describe a continuacin.
4. Aumente la cantidad de tner por rea (M/A). Para ms detalles, consulte la "Accin 3" que se
describe a continuacin.
5. Pida al cliente que cambie el papel de un papel muy resistente a otro ms suave.
Causa 5: Imagen en negro desenfocada
La diferencia de resistencia entre el rodillo de transferencia de imagen y la banda de transferencia de
imagen provoca la imagen en negro desenfocada cuando se imprime una imagen de cobertura alta.
Este sntoma suele producirse especialmente justo despus de la instalacin inicial de la mquina.
700
Procedimiento a adoptar
1. Deje que pasen varias horas si este sntoma aparece justo despus de la instalacin inicial de la
mquina.
2. Si las imgenes granuladas solamente aparecen en reas de imagen en negro con el modo
Impresora a pleno color, seleccione "CMY+K" con el driver de la impresora PCL. Para obtener
detalles, consulte "Accin 1" que se describe a continuacin.
3. Disminuya el gamma de revelado objetivo. Para obtener ms detalles, consulte "Accin 5" que se
describe a continuacin.
4. Disminuya la corriente del rodillo de transferencia de imagen para negro y la corriente del rodillo
de transferencia de papel. Para ms detalles, consulte "Accin 6" que se describe a continuacin.
Causa 6: Imagen granulada en papel pequeo de alta resistencia
La corriente de transferencia tiende a debilitarse en el rea sin papel del rodillo de transferencia de
papel. Como resultado, la corriente de transferencia insuficiente provoca una imagen granulada
cuando utiliza papel de alta resistencia como el papel fotogrfico y el OHP.
Procedimiento a adoptar
701
6. Localizacin de averas
Procedimiento a adoptar
Seleccione "CMY+K" con el driver de la impresora PCL. Para obtener detalles, consulte "Accin
1" que se describe a continuacin.
Lista de acciones
Accin 1
Con este ajuste para PCL, todas las imgenes en BN se imprimen mediante negro puro, incluido el texto.
Procedimiento a adoptar
Seleccione "CMY+K" con el driver de la impresora PCL. (Calidad de impresin -> Color: Manual ->
Reproduccin en gris -> CMY+K)
Accin 2A
Si cambia la corriente de PTR para cada tipo de papel puede solucionar la imagen granulada de la 1
cara del papel.
Procedimiento a adoptar
1. Aumente la corriente de PTR para la 1 cara del papel en incrementos de 2 A hasta +6 A desde
el valor predeterminado.
Modo B/N / Velocidad normal: SP2-403-001
Modo B/N / Velocidad baja: SP2-403-003
Modo a todo color / Velocidad normal: SP2-407-001
Modo a todo color / Velocidad baja: SP2-407-003
2. Si las imgenes granuladas empeoran, disminuya la corriente de PTR en incrementos de 2 A hasta
-6 A desde el valor predeterminado.
3. Si las imgenes granuladas solamente se producen cuando utiliza un tipo especfico de papel, ajuste
la configuracin de tipo de papel a una de las siguientes configuraciones de papel especial.
- Si la configuracin de tipo de papel actual es una de las siguientes, cmbiela a papel especial 1.
Papel normal 1, papel normal 2, grueso medio, papel fino, papel satinado: brillo
Seleccione papel especial 1, luego ajuste las configuraciones de los siguientes modos SP:
Modo B/N / Velocidad normal SP2-753-001
Modo B/N / Velocidad baja: SP2-753-003
Modo a todo color / Velocidad normal: SP2-757-001
Modo a todo color / Velocidad baja: SP2-757-003
702
- Si la configuracin de tipo de papel actual es una de las siguientes, cmbiela a papel especial 4.
Papel grueso 2, papel grueso 2, papel grueso 3
Seleccione papel especial 4, luego ajuste las configuraciones de los siguientes modos SP:
Modo B/N: SP2-783-001
Modo a todo color: SP2-787-001
Accin 2B
Cambiar la corriente de PTR para cada tipo de papel puede solucionar la imagen granulada de la 2
cara del papel.
Procedimiento a adoptar
1. Aumente la corriente de PTR para la 2 cara del papel en incrementos de 2 A hasta +6 A desde
el valor predeterminado.
Modo B/N / Velocidad normal: SP2-403-002
Modo B/N / Velocidad baja: SP2-403-004
Modo a todo color / Velocidad normal: SP2-407-002
703
6. Localizacin de averas
Bsicamente, existen diferentes valores de configuracin para la 1 cara y la 2 cara del papel
grueso cuando se utiliza el modo de impresin bypass. Cuando se utiliza papel grueso en el modo
de impresin bypass, ajuste la corriente de PTR de papel especial 4 para la 2 cara del papel grueso.
Utilice siempre la configuracin ajustada de papel especial 4 cuando se alimente la 2 cara del
papel grueso desde la bandeja bypass.
Accin 3
Aumente la cantidad de tner por rea (M/A). Sin embargo, demasiado tner puede provocar una
rfaga de tner.
Procedimiento a adoptar
1. Ajuste los siguientes modos SP a los valores resaltados en negrita.
Ajuste la configuracin de SP3-501-001 a 0,500 mg/cm2 para M/A mximo: Bk.
Ajuste la configuracin de SP3-501-002 a 0,495 mg/cm2 para M/A mximo: C.
704
705
6. Localizacin de averas
Modo B/N / Velocidad normal o baja para papel fino: SP2-453-001 y -003
Modo B/N / Velocidad baja para papel satinado: SP2-482-001
Modo B/N / Velocidad baja para grueso 1: SP2-502-001
Modo B/N / Velocidad baja para grueso 2: SP 2-553-001
Modo B/N / Velocidad baja para OHP: SP 2-603-001
Modo B/N / Velocidad baja para grueso 3: SP 2-651-001
Modo B/N / Velocidad normal o baja para papel grueso medio: SP2-703-001 a -004
Modo B/N / Velocidad normal o baja para papel especial 1: SP2-753-001 a -004
Modelo B/N / Velocidad normal o baja para papel especial 2: SP2-803-001 a -004
Modo B/N / Velocidad normal o baja para papel especial 3: SP2-852-001 a -004
Modo B/N / Velocidad baja para papel especial 4: SP2-783-001
Modo B/N / Velocidad baja para papel especial 5: SP2-833-001
Modo B/N / Velocidad baja para papel especial 6: SP2-883-001
706
3. Compruebe si la marca roja est pintada fuera del cable negro del motor de suministro de tner. La
imagen izquierda [A] muestra un motor correcto y la imagen derecha [B] muestra un motor
defectuoso.
Sustituya el motor de suministro de tner con un nuevo motor si la marca roja est pintada fuera
del cable rojo del motor de suministro de tner.
707
6. Localizacin de averas
4. Compruebe si el engranaje [A] del motor de suministro de tner est conectado al eje del motor.
Sustituya el motor de suministro de tner con un nuevo motor si el engranaje del motor de
suministro de tner no est conectado al eje del motor.
x 2 cada una).
708
4. Sustituya el embrague unidireccional [A] con Referencia D1051164 si el eje del rodillo de
alimentacin no rota.
709
6. Localizacin de averas
2. Sujete los laterales de la gua final [A] y luego muvala hasta la posicin que se muestra
anteriormente.
711
6. Localizacin de averas
x 2 cada una).
712
4. Sustituya el embrague unidireccional [A] con Referencia D1051164 si el eje del rodillo de
alimentacin no rota.
713
6. Localizacin de averas
2. Sujete los laterales de la gua final [A] y luego muvala hasta la posicin que se muestra
anteriormente.
715
6. Localizacin de averas
716
4. Presione suavemente la superficie del rodillo de transporte vertical [A] de la bandeja 1 con un papel
pequeo, como se muestra anteriormente.
6. Localizacin de averas
4. Presione suavemente la superficie del rodillo de transporte vertical [A] de la bandeja 2 con un papel
pequeo, como se muestra anteriormente.
718
6. Si se sigue produciendo el Atasco 11, sustituya los soportes [A] [B] de las tapas de transporte vertical
(Parte delantera: Referencia D0392943, Parte trasera: Referencia D0392944).
6
2. Presione el soporte del sensor de transporte vertical en el rea alrededor de la protuberancia [A]
como se muestra anteriormente.
3. Si existe un hueco entre esta rea del soporte y el marco que hay debajo de la misma, sustituya el
soporte con Referencia D0392929.
4. Si se sigue produciendo el Atasco 11, sustituya los soportes [A] [B] de las tapas de transporte vertical
(Parte delantera: Referencia D0392943, Parte trasera: Referencia D0392944).
719
6. Localizacin de averas
4. Presione suavemente la superficie del rodillo de transporte vertical [A] de la bandeja 1 con un papel
pequeo, como se muestra anteriormente.
720
7. Presione suavemente la superficie del rodillo de transporte vertical [A] de la bandeja 2 con un papel
pequeo, como se muestra anteriormente.
721
6. Localizacin de averas
2. Sustituya los soportes de las tapas de transporte vertical (Parte delantera: Referencia D0392943,
Parte trasera: Referencia D0392944).
722
2. Sustituya los soportes de tensin de presin (Referencia D3312773) como se muestra anteriormente
con resortes especiales (Referencia D3312774) ( "Motores de elevacin" del manual de servicio
de la PFU).
Efecto secundario:
Estos "resortes especiales" aumentarn la presin de alimentacin de papel. Por tanto, si un cliente utiliza
tipos de papel fino despus de la instalacin de "resortes especiales", pueden producirse alimentaciones
mltiples.
Temperatura de fusin
600 dpi
1200 dpi
Papel especial 2
160C
135C
Papel especial 3
150C
125C
Papel especial 4
723
6. Localizacin de averas
Papel especial 5
Papel especial 6
145C
El papel especial 1-3 est diseado para tipos de papel normal y grueso medio.
El papel especial 4-6 est diseado para tipos de papel equivalentes al papel grueso 1 o ms
gruesos.
El papel especial 2-3 y 5-6 est diseado para solucionar tipos especficos de problemas de imagen,
y el papel especial 1 y 4 est diseado para usarse como un modo personalizado, si los modos 2-6
no resultan eficaces.
Papel especial 1:
Utilice este modo si se produce el problema solamente con un tipo especfico de papel normal o papel
grueso medio, y necesita cambiar (personalizar) la corriente de transferencia de papel o las
configuraciones de temperatura de fusin. Las configuraciones predeterminadas de este modo son
exactamente iguales que las del grueso medio.
Papel especial 2:
Utilice este modo si se produce una fusin deficiente solamente con un tipo especfico de papel normal o
papel grueso medio.
Papel especial 3:
Utilice este modo si las imgenes con ampollas se producen solamente con un tipo especfico de papel
normal o de papel grueso medio.
Papel especial 4:
Utilice este modo si el problema se produce solamente con un tipo especfico de papel grueso, y necesita
cambiar (personalizar) la corriente de transferencia de papel o las configuraciones de temperatura de
fusin. Las configuraciones predetermiandas de este modo son exactamente iguales que las del papel
grueso 1.
Papel especial 5:
Utilice este modo si la fusin deficiente se produce solamente con un tipo especfico de papel grueso.
Papel especial 6:
Utilice este modo si las imgenes con ampollas se producen solamente con un tipo especfico de papel
grueso.
1. En Herramientas del usuario (User Tools), elija el "Tipo de papel" (Paper Type) y el "Grosor de
papel" (Paper Thickness) para la bandeja deseada del siguiente modo:
Equivalente a
Tipo de papel
Papel especial 1
Papel especial 1
Papel especial 2
Papel especial 2
Papel especial 3
Papel especial 3
Papel especial 4
Papel especial 1
Papel grueso 1, 2 o 3
Papel especial 5
Papel especial 2
Papel grueso 1, 2 o 3
Papel especial 6
Papel especial 3
Papel grueso 1, 2 o 3
Papel especial 1 a 3
Bandeja de papel
Tipo de papel
Bandeja 1 a 4
Papel especial 1 a 3
Cualquier
configuracin
Cualquier
configuracin
Papel especial 1 a 3
Papel especial 4 a 6
Papel grueso 1, 2 o 3
Bandeja de fuente de
papel
Tipo de papel
Papel normal o
Grueso medio
Bandeja 1 a 2
Papel especial 4 a 6
Bandeja 3 a 4
Bandeja bypass
725
6. Localizacin de averas
Bandeja 1 a 4
Papel especial 1 a 3
Papel especial 4 a 6
Bandeja deseada
Papel especial 1 a 3
Bandeja 1 a 2
Bandeja deseada
Ninguno
Bandeja 3 a 4
Bandeja bypass
Bandeja bypass
Ninguno
Papel especial 1 a 3
Tipo de papel
Papel especial 1
Papel especial 1
Papel especial 2
Papel especial 2
Papel especial 3
Papel especial 3
2. Dentro del driver de la impresora, elija la "Bandeja de fuente de papel" (Paper Source Tray) y el
"Tipo de papel" (Paper Type) para la misma bandeja y tipo de papel que seleccion en el paso 1
anterior.
Bandeja bypass
Prioridad de "Driver/Comando" (predeterminado)
Dentro del driver de la impresora, elija la "Bandeja de fuente de papel" (Paper Source Tray) para
la bandeja bypass, y el "Tipo de papel" (Paper Type) para el papel especial 1, 2 o 3.
La mquina ignorar la configuracin de "Tipo de papel" (Paper Type) en Herramientas del
usuario (User Tools)
Prioridad "Configuracin de la mquina"
1. En Herramientas del usuario (User Tools), elija el "Tipo de papel" (Paper Type) y el "Grosor de
papel" (Paper Thickness) para la bandeja bypass.
726
Equivalente a
Tipo de papel
Papel especial 1
Papel especial 1
Papel especial 2
Papel especial 2
Papel especial 3
Papel especial 3
2. Dentro del driver de la impresora, elija la "Bandeja de fuente de papel" (Paper Source Tray) para
la bandeja bypass, y el "Tipo de papel" (Paper Type) para el mismo tipo de papel que seleccion
en el paso 1 anterior.
Papel especial 4 a 6
1. En Herramientas del usuario (User Tools), elija el "Tipo de papel" (Paper Type) y el "Grosor de
papel" (Paper Thickness) para la bandeja deseada.
Equivalente a
Tipo de papel
Papel especial 4
Papel especial 1
Papel grueso 1, 2 o 3
Papel especial 5
Papel especial 2
Papel grueso 1, 2 o 3
Papel especial 6
Papel especial 3
Papel grueso 1, 2 o 3
2. Dentro del driver de la impresora, elija la "Bandeja de fuente de papel" (Paper Source Tray) para
la bandeja deseada (del paso 1 anterior), y seleccione para Tipo de papel (Paper Type)
"Ninguno" (None).
Modo
Resolucin
Cara de
(Velocidad del
impresin
proceso)
727
6. Localizacin de averas
Anverso
2-403-001
2-411-005(S2),009(S3),013(S4),
017(S5)
Reverso
2-403-002
2-411-006(S2),010(S3),014(S4),
018(S5)
Anverso
2-403-003
2-411-007(S2),011(S3),015(S4),
019(S5)
Reverso
2-403-004
2-411-008(S2),012(S3),016(S4),
020(S5)
Anverso
2-407-001
2-412-005(S2),009(S3),013(S4),
017(S5)
Reverso
2-407-002
2-412-006(S2),010(S3),014(S4),
018(S5)
Anverso
2-407-003
2-412-007(S2),011(S3),015(S4),
019(S5)
Reverso
2-407-004
2-412-008(S2),012(S3),016(S4),
020(S5)
Cara de
impresin
Corriente
estndar RTR
( A)
600 dpi
(120 mm/s)
Anverso
2-703-001
Reverso
2-703-002
1200 dpi
(60 mm/s)
Anverso
2-703-003
Reverso
2-703-004
600 dpi
(120 mm/s)
Anverso
2-707-001
Reverso
2-707-002
1200 dpi
(60 mm/s)
Anverso
2-707-003
Reverso
2-707-004
600 dpi
(120 mm/s)
B/N
1200 dpi
(60 mm/s)
600 dpi
(120 mm/s)
Color
1200 dpi
(60 mm/s)
Grueso medio
Modo
Resolucin
(Velocidad del
proceso)
B/N
Color
Papel fino
728
Modo
B/N
Color
Resolucin
(Velocidad del
proceso)
Cara de
impresin
600 dpi
(120 mm/s)
Solament
e anverso
2-453-001
1200 dpi
(60 mm/s)
Solament
e anverso
2-453-003
600 dpi
(120 mm/s)
Solament
e anverso
2-457-001
1200 dpi
(60 mm/s)
Solament
e anverso
2-457-003
Modo
Resolucin
(Velocidad del
proceso)
Cara de
impresin
Corriente estndar
RTR
( A)
B/N
60 mm/s
solamente
Solament
e anverso
2-482-001
Color
60 mm/s
solamente
Solament
e anverso
2-483-001
Papel grueso 1
Modo
Resolucin
(Velocidad del
proceso)
Cara de
impresin
Corriente estndar
RTR
( A)
B/N
60 mm/s
solamente
Solament
e anverso
2-502-001
Color
60 mm/s
solamente
Solament
e anverso
2-507-001
Cara de
impresin
Corriente estndar
RTR
( A)
Papel grueso 2
Modo
Resolucin
(Velocidad del
proceso)
729
6. Localizacin de averas
B/N
60 mm/s
solamente
Solament
e anverso
2-553-001
Color
60 mm/s
solamente
Solament
e anverso
2-558-001
Papel grueso 3
Modo
Resolucin
(Velocidad del
proceso)
Cara de
impresi
n
Corriente estndar
RTR
( A)
B/N
60 mm/s
solamente
Solamen
te
anverso
2-651-001
60 mm/s
solamente
Solamen
te
anverso
2-652-001
Color
Transparencias
Modo
Resolucin
(Velocidad del
proceso)
Cara de
impresin
Corriente estndar
RTR
( A)
B/N
60 mm/s
solamente
Solament
e anverso
2-603-001
Color
60 mm/s
solamente
Solament
e anverso
2-608-001
Cara de
impresin
Papel especial 1
Modo
730
Resolucin
(Velocidad del
proceso)
Anverso
2-753-001
Reverso
2-753-002
Anverso
2-753-003
Reverso
2-753-004
Anverso
2-757-001
Reverso
2-757-002
Anverso
2-757-003
Reverso
2-757-004
Cara de
impresin
Corriente estndar
RTR
( A)
600 dpi
(120 mm/s)
Anverso
2-803-001
Reverso
2-803-002
1200 dpi
(60 mm/s)
Anverso
2-803-003
Reverso
2-803-004
600 dpi
(120 mm/s)
Anverso
2-807-001
Reverso
2-807-002
1200 dpi
(60 mm/s)
Anverso
2-807-003
Reverso
2-807-004
600 dpi
(120 mm/s)
B/N
1200 dpi
(60 mm/s)
600 dpi
(120 mm/s)
Color
1200 dpi
(60 mm/s)
Papel especial 2
Modo
Resolucin
(Velocidad del
proceso)
B/N
Color
Papel especial 3
731
6. Localizacin de averas
Modo
B/N
Color
Resolucin
(Velocidad del
proceso)
Cara de
impresin
600 dpi
(120 mm/s)
Anverso
2-852-001
1200 dpi
(60 mm/s)
Anverso
2-852-003
600 dpi
(120 mm/s)
Anverso
2-857-001
1200 dpi
(60 mm/s)
Anverso
2-857-003
Papel especial 4
Modo
Resolucin
(Velocidad del
proceso)
Cara de
impresin
B/N
60 mm/s
solamente
Solament
e anverso
2-783-001
Color
60 mm/s
solamente
Solament
e anverso
2-787-001
Papel especial 5
Modo
Resolucin
(Velocidad del
proceso)
Cara de
impresin
Corriente estndar
RTR
( A)
B/N
60 mm/s
solamente
Solament
e anverso
2-833-001
Color
60 mm/s
solamente
Solament
e anverso
2-837-001
Cara de
impresin
Corriente estndar
RTR
( A)
Papel especial 6
Modo
732
Resolucin
(Velocidad del
proceso)
B/N
60 mm/s
solamente
Solament
e anverso
2-883-001
Color
60 mm/s
solamente
Solament
e anverso
2-887-001
733
6. Localizacin de averas
Deteccin de atascos
Presentacin de atascos de papel
SP7-507 muestra el historial de atascos de papel.
734
Cdigo de tamao
05
A4 LEF
141
B4 SEF
06
A5 LEF
142
B5 SEF
14
B5 LEF
160
DLT SEF
38
LT LEF
164
LG SEF
44
HLT LEF
166
LT SEF
132
A3 SEF
172
HLT SEF
133
A4 SEF
255
Otros
134
A5 SEF
Deteccin de atascos
Presentacin
Descripcin
7504 1
Al encender
Nota
7504 3
Bandeja 1: Activada
A2
7504 4
Bandeja 2: Activada
A1
7504 5
Bandeja 3: Activada
7504 6
Bandeja 4: Activada
7504 8
Bypass: Activado
A2
7504 9
Dplex: Activado
7504 11
Transporte vertical 1:
Activado
A1
7504 12
Transporte vertical 2:
Activado
7504 17
Registro: Activado
7504 18
Entrada de fusin:
Activado
7504 19
7504 20
7504 21
Pantalla
LCD
A2
B
735
6. Localizacin de averas
736
Cdigo de
atasco SP
Presentacin
Descripcin
7504 24
7504 25
7504 27
7504 28
Sensor de salida de 1
separador
7504 29
Salida de papel de
bandeja R: Activado
7504 51
Sensor de transporte
vertical1
A1, A2
7504 52
Sensor de transporte
vertical2
7504 53
Sensor de transporte
vertical3
7504 57
Sensor de registro
7504 58
Sensor de entrada de
fusin
7504 59
7504 60
Sensor de salida
7504 64
Sensor de inversin
7504 65
7504 67
7504 68
Salida de 1 separador:
Activada
7504 69
7504 230
Pantalla
LCD
W
R1, R2
Deteccin de atascos
Cdigo de
atasco SP
Presentacin
Descripcin
7504 231
FIN:Error de comando
7504 240
7504 241
R1, R2
7504 242
R1, R2
7504 243
Motor de grapadora
R1, R2
7504 244
R1, R2
7504 245
R1, R2
7504 246
Motor de accionamiento
de la unidad de la
grapadora
R1, R2
7504 247
Motor de la bandeja de
salida
R1, R2
7504 248
Solenoide de elevacin
de la banda
R1, R2
R1, R2
7504 249
Pantalla
LCD
R1, R2
C, R1, R2
737
6. Localizacin de averas
Cdigo de
atasco SP
Presentacin
Descripcin
Pantalla
LCD
7504 250
Motor de perforacin
R1, R2
7504 251
R1, R2
7504 252
FIN:Error de posicin de
la grapadora
R1, R2
7504 253
R1, R2
La visualizacin de la ubicacin del atasco depende del lugar en que se detect un atasco de papel
al encender.
738
Cdigo de
atasco SP
Presentacin
Descripcin
Pantalla
LCD
7505 1
Al encender
7505 3
Correccin de
desviacin: Activada
7505 4
Registro: Activado
7505 5
7505 53
Correccin de
desviacin: Desactivada
7505 54
Registro: Desactivado
7505 55
Salida de papel:
desactivada
Deteccin de atascos
739
6. Localizacin de averas
SW4
Interruptor de apertura
de unidad dplex
Activ
o
CN
CN232/2
Condicin
Sntoma
Abierta
Se muestra "Open
Cover" (Tapa abierta).
Cortocirc
uito
Abierta/
Sensor ID: Frontal
CN214/8, 9
Cortocirc
uito
SC400
Abierta/
S5
CN214/6, 7
CN214/2, 3
Cortocirc
uito
SC400
Abierta/
S19
740
S6
Sensor de registro
S35
Cortocirc
uito
SC400
Abierta/
H
CN232/4
CN214/11
Cortocirc
uito
SC452
Abierta
Atasco A2 (Atasco17)
Cortocirc
uito
Atasco B (Atasco57)
Abierta/
H
CN220/2
Cortocirc
uito
SC380/SC396
Nombre de sensor/
N.
S36
Activ
o
CN
S22
S23
S24
Sensor de tner
agotado: M
Sensor de tner
agotado: C
CN220/17
CN234/14,
17, 20, 23
Cortocirc
uito
S12
S10
S8
S9
Sensor 1, 2
S11
Sensor de transporte
vertical 2
SC381/SC397
Abierta
No se detecta el fin de
tner.
Cortocirc
uito
Sensor de tner
agotado: K
Sensor de rotacin de la
ITB
Sntoma
Abierta/
H
Sensor de tner
agotado: Y
S21
Condicin
Abierta/
H/L
CN219/20
CN219/10
Cortocirc
uito
SC443
Abierta
Atasco A1 (Atasco11)
Cortocirc
uito
Abierta
No se detecta Papel
agotado cuando ya no
queda papel en la bandeja
de papel.
Cortocirc
uito
Abierta
Atasco Y (Atasco12)
Cortocirc
uito
Atasco Y (Atasco52)
CN214/17,
19
CN219/15
741
6. Localizacin de averas
Nombre de sensor/
N.
Activ
o
CN
Condicin
Sntoma
Abierta/
SW6
S13
742
S15
Conmutador de tamao
del papel de la bandeja
1
Sensor de tamao de
papel bypass
S14
Sensor de longitud de
papel bypass
S16
Sensor de posicin
inicial de bypass
S7
Sensor de entrada de
fusin
S17
Sensor de entrada
dplex
CN211/11,
12, 13, 15
Cortocirc
uito
Cortocirc
uito
CN221/9,
10, 12, 13
La bandeja 1 se detecta
cuando la bandeja 1 no
est instalada.
Abierta/
Cortocirc
uito
Abierta
No se detecta papel en la
bandeja bypass aunque se
haya colocado papel.
Cortocirc
uito
Se detecta papel en la
bandeja bypass aunque no
se haya colocado papel.
CN221/18
Abierta
L
CN221/15
Cortocirc
uito
Abierta/
H
CN221/21
CN214/14
CN221/24
Cortocirc
uito
SC508
Abierta
Atasco B (Atasco18)
Cortocirc
uito
Atasco C (Atasco58)
Abierta
Atasco Z (Atasco27)
Cortocirc
uito
Atasco Z (Atasco67)
Nombre de sensor/
N.
S18
Activ
o
CN
CN221/27
S34
Sensor TD - K
CN212/B9,
B11
S32
Sensor TD - M
CN212/A9,
A11
CN212/B3,
B5
CN212/A3,
A5
S33
Sensor TD - C
S31
Sensor TD - Y
S26
Sensor de salida de
fusin
S30
Sensor de botella de
recogida de tner de la
PCDU llena
CN227/18
Condicin
Sntoma
Abierta
Atasco Z (Atasco25)
Cortocirc
uito
Atasco Z (Atasco65)
Abierta/
Cortocirc
uito
SC372
Abierta/
Cortocirc
uito
SC373
Abierta/
Cortocirc
uito
SC374
Abierta/
Cortocirc
uito
SC375
Abierta
Atasco C (Atasco19)
Cortocirc
uito
Atasco C (Atasco59)
Abierta
Cortocirc
uito
CN211/9
743
6. Localizacin de averas
Nombre de sensor/
N.
SW5
S29
Switch de instalacin de
la botella de recogida de
tner de la PCDU
Sensor de botella de
recogida de tner de la
ITB llena
Activ
o
CN
Condicin
Sntoma
Abierta
La botella de recogida de
tner no se detecta cuando
est instalada la botella de
tner residual.
Cortocirc
uito
La botella de recogida de
tner se detecta cuando no
est instalada la botella de
tner residual.
Abierta
Cortocirc
uito
CN211/7
CN211/4
Abierta/
SW7
S37
Conmutador de tamao
del papel de la bandeja
2
Temperatura/
Sensor de humedad
CN211/16,
17, 18, 20
Cortocirc
uito
Cortocirc
uito
CN222/15,
17
Abierta/
Cortocirc
uito
La bandeja 2 se detecta
cuando la bandeja 2 no
est instalada.
La imagen impresa tiene
algunos problemas tales
como imagen poco
precisa, fondo sucio,
imagen dbil o fusin
insuficiente.
Abierta/
S28
744
Termopila
CN237/14
Cortocirc
uito
SC541
Nombre de sensor/
N.
TH1
TH2
Termistor de rodillo de
presin 1 (Centro)
TH3
Termistor de rodillo de
presin 2 (Extremos)
S27
S1
Sensor 1 de longitud de
originales
S2
Sensor 2 de longitud de
originales
S3
Sensor de posicin
inicial del escner
S4
S20
Sensor de contacto de la
ITB
Activ
o
CN
Condicin
Sntoma
Abierta/
A
CN233/4
Cortocirc
uito
SC551
Abierta/
A
CN233/11
Cortocirc
uito
SC561
Abierta/
A
CN233/9
CN227/21
Cortocirc
uito
SC571
Abierta
Atasco C (Atasco20)
Cortocirc
uito
Atasco C (Atasco60)
Abierta/
A
CN206/2
Cortocirc
uito
Abierta/
CN206/5
CN205/2
Cortocirc
uito
CN205/5
No se detecta el tamao de
papel original.
No se detecta el tamao de
papel original.
Abierta
SC120
Cortocirc
uito
SC121
Abierta/
Cortocirc
uito
Abierta/
L
CN234/5
Cortocirc
uito
SC442
745
6. Localizacin de averas
Nombre de sensor/
N.
S25
Sensor de inversin
SW2
Interruptor de apertura
de la puerta inferior
derecha
Activ
o
CN
CN227/15
CN219/13
Condicin
Sntoma
Abierta
Cortocirc
uito
Atasco C (Atasco64)
Abierta
Se muestra "Open
Cover" (Tapa abierta).
Cortocirc
uito
Unidad de alimentacin
Fusible
Clasificacin
120 V
220 V - 240 V
FU101
15A/125V
8A/250 V
FU102
10A/125V
5A/250V
FU103
2A/250V
2A/250V
FU5
5A/250V
5A/250V
FU6
5A/250V
5A/250V
No se suministran 5 VS al controlador.
FU7
10A/125V
10 A/250 V
No se suministran 24 VS a la BCU.
FU8
10A/125V
10 A/250 V
No se suministran 24 VS a la BCU.
FU9
10A/125V
10 A/250 V
Para disfrutar de una proteccin continua en contra de incendios, cambie los fusibles por unos del
mismo tipo y rgimen nominal.
746
Puede comprobar la placa de la IPU con el men del modo SP, SP4-904-1.
Si no se detecta un error, la prueba finaliza. Luego se muestra el cdigo de finalizacin en la pantalla del
panel de mandos. Si se detecta un error, se interrumpe la prueba. Luego se muestra un cdigo de error.
La siguiente tabla enumera los cdigos de finalizacin y de error.
747
6. Localizacin de averas
Condensacin
2. Destruccin de los elementos del circuito
El exceso de corriente o un elemento defectuoso rompe el circuito.
3. Suministro de energa anmalo
No se suministra el voltaje necesario a los dispositivos.
4. Exceso de calor/exceso de fro
El entorno es inadecuado para la placa (la unidad del escner).
5. Electricidad esttica
Se produce electricidad esttica de alto voltaje durante la prueba.
6. Otros
El escner y la IPU estn conectados incorrectamente.
Cuando haya completado una comprobacin, apague y encienda el interruptor principal antes de realizar
otra comprobacin. Cuando haya completado todas las comprobaciones necesarias, apague y encienda
el interruptor principal.
748
7. Ahorro de energa
Ahorro de energa
Modos ahorro de energa
Los clientes deben utilizar los modos de ahorro de energa correctamente para ahorrar energa y proteger
el medio ambiente.
El rea sombreada en este diagrama representa la cantidad de energa que se ahorra cuando los
temporizadores se ajustan a sus valores predeterminados. Si se cambian los temporizadores, la energa
ahorrada ser diferente. Por ejemplo, si todos los temporizadores se ajustan a 240 min., el rea gris
desaparecer y no se ahorrar nada de energa antes de que transcurran los 240 min.
Ajustes de temporizador
El usuario puede ajustar estos temporizadores con User Tools (Herramientas de usuario)[System Settings
> Timer Settings (> Ajustes del sistema > Ajustes de temporizador)].
Temporizador de desconexin automtica (1 240 min): Desconectado/En espera
Ajuste predeterminado: 1 min.
749
7. Ahorro de energa
Recomendacin
Se recomienda mantener los ajustes predeterminados.
Si el cliente quiere cambiar estos ajustes, explquele que sus gastos de energa podran aumentar,
con el consiguiente efecto sobre el medio ambiente debido al uso de esa energa extra.
Si fuera necesario cambiar los ajustes, trate de asegurarse de que el temporizador de desconexin
automtica no tiene un valor excesivo. Primero pruebe con un valor ms pequeo (30 min. por
ejemplo) y, si el cliente no est satisfecho, pase a otro mayor (60 min.).
Si se ajustan todos los temporizadores a su valor mximo, la mquina no empezar a ahorrar energa
hasta que hayan trascurrido 240 minutos despus del ltimo trabajo. Esto significa que despus de
que el cliente haya terminado de usar la mquina ese da, se consumir la energa que podra haberse
ahorrado.
Si cambia los ajustes, la energa consumida puede medirse con SP8941, como se explica a
continuacin.
750
Ahorro de energa
Al comienzo del periodo de medicin, lea los valores de SP8941 001 a 005.
Al final del periodo de medicin, vuelva a leer los valores de SP8941 001 a 005.
Calcule la cantidad de tiempo pasado en cada modo (reste la primera medicin de la ltima).
Multiplique el resultado por el consumo elctrico especificado para cada modo.
Convierta el resultado a kWh (kilovatios hora)
A continuacin se ofrece un ejemplo de clculo:
Mquina
Fecha
Modo de
funciona
miento
Modo
listo (en
espera)
Modo de
ahorro de
energa
(Panel
desactiva
do)
Modo de
bajo
consumo
Off/
Modo en
espera
Consumo
elctrico (W):
Datos: a
SP8941:
Estado de
la
mquina
Diferencias
Tiempo de
de tiempo
Tiempo de
finalizacin: (Datos:b inicio: (min.)
(min.)
Datos: c)
Datos: b
Datos: c
(min.) Datos:
d
Consumo
de energa
(Datos:a x
Datos:d)
(Wmin.)
21089.0
321294.6
Datos: e
1081.8
001:
Tiempo
de
funciona
miento
214.0
002:
Tiempo en 306163.0
espera
308046.0
1883.0
402962.0
214.0
003:
Tiempo
de ahorro 71386.0
de
energa
75111.0
3725.0
797150.0
153.0
004:
Tiempo
de bajo
consumo
154084.0
156340.0
2256.0
345168.0
7.0
005:
Tiempo
modo
apagado
508776.0
520377.0
11601.0
81207.0
21386.0
297.0
19762.0
751
7. Ahorro de energa
752
329.37
1947781.6
0
32.46
Ahorro de papel
Ahorro de papel
Eficacia de la funcin dplex/combinar
Las funciones dplex/combinar reducen la cantidad de papel utilizado. Esto hace que se utilice menos
energa en general para la produccin del papel, lo que mejora el medio ambiente.
1. Dplex:
2. Modo Combinar:
753
7. Ahorro de energa
3. Dplex + Combinar
Al utilizar ambas funciones a la vez, puede reducirse tres cuartas partes el volumen de papel.
Para comprobar el consumo de papel, consulte el contador de totales y el contador dplex.
El contador de totales cuenta todas las pginas impresas.
Por cada pgina dplex, el contador de totales suma 2.
Para un trabajo dplex de un original de tres pginas, el contador de totales suma 3.
El contador dplex cuenta las pginas que tienen imgenes en ambos lados.
Recomendacin
Explique estas funciones a los clientes para que puedan reducir el uso de papel.
Modelo DI-C1.5
Contador de totales: SP 8581-001
Contador dplex: SP 8411-001
Modo de una cara con Combinar: SP 8421-004
Modo dplex con Combinar: SP 8421-005
La siguiente tabla muestra el ahorro de papel y cmo los contadores se incrementan con algunos ejemplos
de trabajos de una sola cara y dplex.
Modo dplex:
754
Ahorro de papel
Contador dplex
Originales
Hoja simple
utilizada
Hojas dplex
utilizadas
Papel
ahorrado
Contador total
SP8501-001
Dplex (SP8411
001)
10
10
10
20
20
10
10
20
10
Si se utiliza el modo combinado, los contadores de totales y dplex funcionan de la misma forma que se
ha explicado anteriormente. La siguiente tabla muestra el ahorro de papel y cmo los contadores se
incrementan con algunos ejemplos de trabajos dplex/combinados.
Modo 2 en 1:
Originales
Hoja simple
utilizada
Hojas dplex
utilizadas
Papel
ahorrado
Contador total
Contador dplex
SP8501-001
SP8421-004
10
10
20
20
10
10
10
10
Dplex + Modo 2 en 1:
Originales
Hoja simple
utilizada
Hojas dplex
utilizadas
Papel
ahorrado
Contador total
Contador dplex
SP8501-001
SP8421-005
1
755
7. Ahorro de energa
756
Originales
Hoja simple
utilizada
Hojas dplex
utilizadas
Papel
ahorrado
Contador total
Contador dplex
SP8501-001
SP8421-005
10
10
11
11
12
12
Model DI-C1.5
Machine Code: D104/D106
Appendices
17 December, 2010
TABLE OF CONTENTS
1. Appendix: Specifications
General Specifications.......................................................................................................................................3
Copier.............................................................................................................................................................3
Printer...............................................................................................................................................................7
Scanner...........................................................................................................................................................8
Supported Paper Sizes.......................................................................................................................................9
Paper Feed......................................................................................................................................................9
Paper Exit......................................................................................................................................................12
Platen/ARDF Original Size Detection........................................................................................................16
Software Accessories.......................................................................................................................................18
Printer and LAN Fax Drivers........................................................................................................................18
Scanner Driver.............................................................................................................................................18
Utility Software.............................................................................................................................................19
Optional Equipment.........................................................................................................................................20
ARDF (D541)...............................................................................................................................................20
Paper Feed Unit (D425)..............................................................................................................................20
Paper Feed Unit (D331)..............................................................................................................................21
Internal Finisher (D429) and Punch Unit (D390)......................................................................................22
Shift Tray (D428).........................................................................................................................................23
1-bin Tray Unit (D426)...............................................................................................................................23
Side Tray (D427).........................................................................................................................................24
Envelope Feeder EF3010 (D559).............................................................................................................24
System SP4xxx...............................................................................................................................................207
SP4-XXX (Scanner)....................................................................................................................................207
System SP5xxx...............................................................................................................................................230
SP5-XXX (Mode).......................................................................................................................................230
System SP6xxx...............................................................................................................................................295
SP6-XXX (Peripherals)...............................................................................................................................295
System SP7-xxx..............................................................................................................................................298
SP7-XXX (Data Log)..................................................................................................................................298
System SP8-xxx..............................................................................................................................................333
SP8-xxx: Data Log2..................................................................................................................................333
Input and Output Check Tables....................................................................................................................377
Input Check Table.....................................................................................................................................377
Output Check Table..................................................................................................................................386
Test Pattern Printing........................................................................................................................................393
Printer Service Mode.....................................................................................................................................395
SP1-XXX (Service Mode)..........................................................................................................................395
Scanner SP Mode..........................................................................................................................................404
SP1-xxx (System and Others)...................................................................................................................404
SP2-XXX (Scanning-image quality)..........................................................................................................405
INDEX...........................................................................................................................................................407
1. Appendix: Specifications
General Specifications
Copier
Configuration:
Print Process:
Resolution:
Gradation:
Desktop
Laser beam scanning & Dry electrostatic transfer system
4 drums tandem method
Scan: 600 dpi
Print: 600 dpi/ 1200 dpi
Scan: 8 bits/pixel each for RGB/ 600 dpi 1 bit/pixel
Print: 600dpi / 4 bits/pixel
Original type:
A3/11" x 17"
1. Appendix: Specifications
Warm-up time:
General Specifications
Tray 1/ Tray 2
By-pass
Optional Tray
Minimum
A5 (LEF)/
8.5" x 11"
90 x 148 mm
A5 (LEF)/
8.5" x 11"
Maximum
A3/11" x 17"
305 x 600 mm
A3/11" x 17"
Continuous copy:
Up to 999 sheets
1. Appendix: Specifications
Zoom:
Memory:
Power Source:
NA
Europe
25%
25%
50%
50%
65%
65%
73%
71%
78%
75%
85%
82%
93%
93%
100%
100%
121%
115%
129%
122%
155%
141%
200%
200%
400%
400%
Standard: 1.5 GB
120 V - 127 V, 60 Hz: 12A or more (for North America)
220 V - 240 V, 50/60 Hz: 8A or more (for Europe/ASIA)
-
Power Consumption:
Maximum
Sleep Mode
120V
220 - 240V
1600 W or less
1680 W or less
2.0 W or less
2.0 W or less
(*1) The complete system consists of mainframe, ARDF, finisher, and LCT.
The above measurements were made in accordance with Ricoh standard methodology.
Dimensions (W x D x H):
Copier: 587 x 676 x 725 mm (23.1" x 26.7" x 28.5")
Copier + PFU + Right tray + Internal finisher: 1009 x 676 x 1117 mm (39.7" x 26.7" x 44.0")
General Specifications
Weight:
Printer
PCL 5c/6 (standard)
Printer Languages:
Resolution and
Gradation:
Printing speed:
Resident Fonts:
13 International fonts
Adobe PostScript 3 (Optional):
136 fonts (24 Type 2 fonts, 112 Type 14 fonts)
USB2.0: Standard
Ethernet (100 Base-TX/10 Base-T): Standard
Host Interfaces:
1. Appendix: Specifications
Network Protocols:
HDD
160 GB (standard)
Scanner
Standard Scanner
Resolution:
Available scanning
Resolution Range:
Grayscales:
Scanning Throughput
(ARDF mode):
Interface:
Compression Method:
1 bit or 8 bits/pixel
Scan to E-mail / Folder:
BW: 44 ipm (A4LEF / BW Text (Print) / 200dpi /Compression: On (MH))
FC: 44 ipm (A4LEF / FC Text / Photo / 200dpi / Compression: Standard)
Ethernet (100 Base-TX/10 Base-T/1000 Base-T for TCP/IP),
Wireless LAN, USB2.0/SD Slot
B&W: TIFF (MH, MR, MMR)
Gray Scale, Full Color: JPEG
Paper Feed
North America
BT: By-pass Tray, T1/2: Tray 1/2 (standard), T3/4: Tray 3/4 (option), DU: Duplex Unit
Paper
Size
(W x L)
BT
T1/2
T3/4
DU
A3 W
12" x 18"
A3 SEF
297 x 420mm
S1
S1
A4 SEF
210 x 297mm
A4 LEF
297 x 210mm
S3
S3
A5 SEF
148 x 210mm
A5 LEF
210 x 148mm
A6 SEF
105 x 148mm
B4 SEF
257 x 364mm
S2
S2
B5 SEF
182 x 257mm
B5 LEF
257 x 182mm
S4
S4
B6 SEF
128 x 182mm
Ledger
11" x 17"
A1
A1
Letter SEF
8.5" x 11"
Letter LEF
11" x 8.5"
A3
A3
Legal SEF
8.5" x 14"
A2
A2
Government Legal
SEF
8.25" x 14"
5.5" x 8.5"
1. Appendix: Specifications
Size
Paper
(W x L)
BT
T1/2
T3/4
DU
Executive SEF
7.25" x 10.5"
Executive LEF
10.5" x 7.25"
A4
A4
8" x 13"
8.5" x 13"
8.25" x 13"
11" x 15"
10" x 14"
8" x 10"
8K
267 x 390mm
16K SEF
195 x 267mm
16K LEF
267 x 195mm
F SEF
Foolscap SEF
Folio SEF
Custom
Com10 Env.
4.125" x 9.5"
Monarch Env.
3.875" x 7.5"
C6 Env.
114 x 162mm
C5 Env.
162 x 229mm
DL Env.
110 x 220mm
Remarks:
A
10
Paper size which has same superscript number can be changeable with SP setting. (eg.
Ledger: A1 <=> A3 SEF: S1)
Not supported
Europe/ Asia
BT: By-pass Tray, T1/2: Tray 1/2 (standard), T3/4: Tray 3/4 (option), DU: Duplex Unit
Paper
Size
(W x L)
BT
T1/2
T3/4
DU
A3 W
12" x 18"
A3 SEF
297 x 420mm
A1
S1
A4 SEF
210 x 297mm
A4 LEF
297 x 210mm
A3
A3
A5 SEF
148 x 210mm
A5 LEF
210 x 148mm
A6 SEF
105 x 148mm
B4 SEF
257 x 364mm
A2
A2
B5 SEF
182 x 257mm
B5 LEF
257 x 182mm
A4
A4
B6 SEF
128 x 182mm
Ledger
11" x 17"
S1
S1
Letter SEF
8.5" x 11"
Letter LEF
11" x 8.5"
S3
S3
Legal SEF
8.5" x 14"
S2
S2
Government Legal
SEF
8.25" x 14"
5.5" x 8.5"
Executive SEF
7.25" x 10.5"
Executive LEF
10.5" x 7.25"
S4
S4
8" x 13"
8.5" x 13"
F SEF
Foolscap SEF
11
1. Appendix: Specifications
Size
Paper
BT
T1/2
T3/4
DU
8.25" x 13"
11" x 15"
10" x 14"
8" x 10"
8K
267 x 390mm
16K SEF
195 x 267mm
16K LEF
267 x 195mm
(W x L)
1
Folio SEF
Custom
Com10 Env.
4.125" x 9.5"
Monarch Env.
3.875" x 7.5"
C6 Env.
114 x 162mm
C5 Env.
162 x 229mm
DL Env.
110 x 220mm
Remarks:
A
Paper size which has same superscript number can be changeable with SP setting. (eg.
Ledger: S1 <=> A3 SEF: A1)
Not supported
Paper Exit
Mainframe and optional trays
Main: Mainframe/ 1-bin: 1-bin tray/ Shift: Shift Tray/ Side: Side Tray
12
Paper
Size (W x L)
Main
1-bin
Shift
Side
A3 W
12" x 18"
A3 SEF
297 x 420 mm
A4 SEF
210 x 297 mm
A4 LEF
297 x 210 mm
A5 SEF
148 x 210 mm
A5 LEF
210 x 148 mm
A6 SEF
105 x 148 mm
B4 SEF
257 x 364 mm
B5 SEF
182 x 257 mm
B5 LEF
257 x 182 mm
B6 SEF
128 x 182 mm
Ledger
11" x 17"
Letter SEF
8.5" x 11"
Letter LEF
11" x 8.5"
Legal SEF
8.5" x 14"
8.25" x 14"
5.5" x 8.5"
Executive SEF
7.25" x 10.5"
Executive LEF
10.5" x 7.25"
F SEF
8" x 13"
Foolscap SEF
8.5" x 13"
Government
Legal SEF
13
1. Appendix: Specifications
Paper
Size (W x L)
Main
1-bin
Shift
Side
8.25" x 13"
11" x 15"
10" x 14"
8" x 10"
8K
267 x 390 mm
16K SEF
195 x 267 mm
16K LEF
267 x 195 mm
Folio SEF
Custom
Com10 Env.
4.125" x 9.5"
Monarch Env.
3.875" x 7.5"
C6 Env.
114 x 162 mm
C5 Env.
162 x 229 mm
DL Env.
110 x 220 mm
Remarks:
Y
Supported
Not supported
Internal Finisher
Str: Straight Feed Out/ Inv: Inverter Path/ Srt; Sort/ Stp: Staple/ 2/3P: 2/3 Holes Punch/ 4P: 4 Holes
Punch/ S4P: Scandinavia 4 Holes Punch/ RT: Right Tray
Paper
14
Size (W x L)
Internal finisher
Str
Inv
Srt
Stp
2/3P
4P
S4P
A3 W
12" x 18"
A3 SEF
297 x 420 mm
10
30
A4 SEF
210 x 297 mm
20
50
Y*
Paper
Size (W x L)
Internal finisher
Str
Inv
Srt
Stp
2/3P
4P
S4P
A4 LEF
297 x 210 mm
20
50
A5 SEF
148 x 210 mm
A5 LEF
210 x 148 mm
A6 SEF
105 x 148 mm
B4 SEF
257 x 364 mm
10
30
B5 SEF
182 x 257 mm
20
50
B5 LEF
257 x 182 mm
20
50
B6 SEF
128 x 182 mm
Ledger
11" x 17"
10
30
Letter SEF
8.5" x 11"
20
50
Y*
Letter LEF
11" x 8.5"
20
50
Legal SEF
8.5" x 14"
10
30
Y*
8.25" x 14"
10
30
5.5" x 8.5"
Executive SEF
7.25" x 10.5"
20
50
Executive LEF
10.5" x 7.25"
20
50
F SEF
8" x 13"
Foolscap SEF
8.5" x 13"
10
30
Y*
8.25" x 13"
10
30
11" x 15"
10
30
10" x 14"
8" x 10"
267 x 390 mm
10
30
Government
Legal SEF
Folio SEF
8K
15
1. Appendix: Specifications
Paper
Size (W x L)
Internal finisher
Str
Inv
Srt
Stp
2/3P
4P
S4P
16K SEF
195 x 267 mm
16K LEF
267 x 195 mm
20
50
Custom
Com10 Env.
4.125" x 9.5"
Monarch Env.
3.875" x 7.5"
C6 Env.
114 x 162 mm
C5 Env.
162 x 229 mm
DL Env.
110 x 220 mm
Remarks:
Y
30
Output up to 30 sheets
50
Output up to 50 sheets
Not supported
16
Size
Platen
ARDF
Platen
ARDF
Inches
Inches
Metric
Metric
A3 (297 x 420) L
Y*3
B4 (257 x 364) L
Y*3
A4 (210 x 297) L
Y*1
Y*3
A4 (297 x 210) S
Y*3
Y*3
B5 (182 x 257) L
Y*3
B5 (257 x 182) S
Y*3
A5 (148 x 210) L
-*1
A5 (210 x 148) S
B6 (128 x 182) L
B6 (182 x 128) S
Y*2
Y*2
11" x 15"
Y*2
10" x 14"
Y*2
Y*2
Y*4
Y*4
8.25" x 13"
Y*4
Y*4
8" x 13"(F)
Y*4
Y*4
Y*3
Y*2
Y*3
Y*2
Y*3
Y*2
Y*3
Y*2
Y*2
-*1
8K (267 x 390)
Y*3
Y*2
Y*3
Y*2
Y*3
Y*2
Y*2
8" x 10"
*1: Use SP4-303 to detect original sizes as A5 lengthwise/HLT when the message Can-t detect original
size shows.
*2: The machine can detect the paper size depending on the setting of SP6-016-1.
*3: The machine can detect the paper size depending on the setting of SP4-305-1.
*4: The machine can detect the paper size depending on the setting of SP5-126-1.
17
1. Appendix: Specifications
Software Accessories
1
The printer drivers and utility software are provided as following two CD-ROMs
1: Printer Drivers and Utilities CD-ROM
2: Scanner Drivers and Utilities CD-ROM.
An auto-run installer lets you to select the components you want to install.
Printer Language
MacOS8.6 to 9.x,
MacOSX10.1
or later
PCL5c
/ PCL6
Yes
No
PS3
Yes
Yes
RPCS
No
No
The PCL5c/6 and PS3 drivers are provided on the printer drivers CD-ROM
The PS3 drivers are all genuine Adobe PS drivers, except for Windows 2000/XP/2003/Vista/7.
Windows 2000 uses Microsoft PS. A PPD file for each operating system is provided with the driver.
The PPD installer for Macintosh supports Mac OS X 10.1 or later versions.
The LAN Fax driver lets you fax documents directly form your PC. Address Book Editor and Cover
Sheet Editor are to be installed as well. (These require the optional fax unit.)
Scanner Driver
Printer Language
Network TWAIN
Yes
No
or later
18
Software Accessories
Utility Software
Software
Description
Font Manager
(2000/XP/Server 2003/7)
(Mac)
19
1. Appendix: Specifications
Optional Equipment
1
ARDF (D541)
Simplex
Paper Size/Weight:
Duplex
Size
Weight
Size
Weight
Table Capacity:
Separation:
Original Transport:
Roller transport
Fax
32 to 200 %
Color
32.6 to 200 %
48.9 to 200 %
Power Source:
Power Consumption:
50 W or less
Dimensions (W x D x H):
Weight:
10 kg (22 lb.)
20
Capacity:
500 sheets
Paper Weight:
Optional Equipment
Paper Size:
Power Source:
Power Consumption:
15 W
Dimensions (W x D x H):
Weight:
Paper Weight:
60 - 105 g/m2, 16 - 28 lb
Tray Capacity:
Power Source:
120 Vac (120 V version) from the copier/printer when the optional
tray heater is installed
220 240 Vac (230 V version) from the copier/printer when the
optional tray heater is installed
Power Consumption:
35 W (Copying/printing)
Weight:
25 kg (55 lb)
Size (W x D x H):
21
1. Appendix: Specifications
Paper Weight:
Tray Capacity:
Staple capacity:
Staple position:
Staple replenishment:
22
Optional Equipment
Power consumption:
50 W + 12 W (Punch Unit)
Finisher:
Dimensions (W x D x H):
13 kg (28.6 lb.)
Paper Size:
Non-standard sizes
Width: 90 to 305 mm
Length: 148 to 600 mm
Paper Weight:
Power Consumption:
Dimension (W x D x H):
Weight:
Standard Size:
A3 /DLT to A5/ HLT SEF
Paper Weight:
Tray Capacity:
Power Source:
Power Consumption:
Less than 1 W
23
1. Appendix: Specifications
Weight:
Size (W x D x H):
Standard Size:
A3 /DLT to A5/ HLT SEF
Paper Weight:
Tray Capacity:
Power Source:
Power Consumption:
Less than 40 W
Weight:
1.5 kg
Size (W x D x H):
Paper Weight:
Tray Capacity:
24
Power Source:
Power Consumption:
Weight:
Size (W x D x H):
Mainframe
Item
60K
120K
240K
EM
Remarks
Scanner
Reflector
Optics cloth
1st/2nd/3rd Mirrors
Optics cloth
Dry cloth
Exposure Glass
Dry cloth
Dry cloth
APS Sensor
Dry cloth
PCDU
Drum Unit-K, C, M, Y
25
Item
60K
120K
240K
EM
Remarks
ID Sensors
Alcohol
Fusing
Alcohol
Pressure Roller
C*
Dry cloth
Dry cloth
Alcohol
Alcohol
Stripper Plate
Alcohol
Thermopile
Dry cloth
*: Clean it if dirty.
S552R
R
Dry cloth
Others
Dust Filter
The cleaning unit prevents the pressure roller from getting dirty due to paper dust.
Item
60K
120K
240K
EM
Remarks
Paper Feed
Feed Roller: Tray 1/2
Damp cloth
Dry cloth
Registration Roller
Registration Sensor
26
C*1
C
C
Damp cloth
Never use alcohol.
Dry cloth
Maintenance Tables
Item
60K
120K
240K
EM
Remarks
Damp cloth
Dry cloth
Damp cloth
Dry cloth
By-pass HP Sensor
Dry cloth
Vacuum
Damp cloth
Dry cloth
Damp cloth
Inverter Roller
Damp cloth
Damp cloth
Inverter Sensor
Dry cloth
Dry cloth
Duplex
Paper Exit
*1: The registration roller requires a cleaning maintenance every 60 K (total count).
Mainframe
Item
240K
EM
Remarks
PCDU
27
Development Unit-K, C, M, Y
PTR unit
Fusing
Fusing Unit
ARDF (D366)
Item
80K
EM
Remarks
Pick-up Roller
Number of originals
Feed Belt
Number of originals
Separation Roller
Number of originals
Sensors
Blower brush
White Plate
Drive Gear
Grease G501
Transport Roller
Exit Roller
Inverter Roller
Idle Rollers
60K
Feed Roller
Bottom Plate Pad
28
120K
EM
Remarks
Dry cloth
Dry cloth
Maintenance Tables
Friction Pad
Dry cloth
Dry cloth
60K
120K
EM
Remarks
Dry cloth
Friction Pad
Dry cloth
Dry cloth
Relay Rollers
Dry cloth
Dry cloth
Relay Clutch
Replace if necessary
Replace if necessary
150K
EM
Exit Rollers
Idle Rollers
Tray
Remarks
Damp or Dry cloth
Damp or Dry cloth
Damp cloth
Blower brush
Paper Sensor
Blower brush
Bearing
S552R
Exit Sensor
EM
Remarks
29
Tray
30
Damp cloth
Adjusts the leading edge registration by changing the registration motor operation timing
for each mode.
Increasing a value: an image is moved to the trailing edge of paper.
Decreasing a value: an image is moved to the leading edge of paper.
001 Tray:Plain:600dpi
*ENG
002 Tray:Thick1:600dpi
*ENG
003 Tray:M-Thick:600dpi
*ENG
004 By-pass:Plain:600dpi
*ENG
005 By-pass:Thick1:600dpi
*ENG
006 By-pass:Thick2:600dpi
*ENG
007 By-pass:Thick3:600dpi
*ENG
*ENG
009 Duplex:Plain:600dpi
*ENG
010 Duplex:M-Thick:600dpi
*ENG
31
011 Tray:Thick1:1200dpi
*ENG
012 Tray:M-Thick:1200dpi
*ENG
013 By-pass:Plain:1200dpi
*ENG
014 By-pass:Plain:1200dpi
*ENG
015 By-pass:Thick1:1200dpi
*ENG
016 By-pass:Thick2:1200dpi
*ENG
017 By-pass:Thick3:1200dpi
*ENG
018 By-pass:M-Thick:1200dpi
*ENG
019 Duplex:Plain:1200dpi
*ENG
020 Duplex:M-Thick:1200dpi
*ENG
[Side-to-Side Registration]
1002
Adjusts the side-to-side registration by changing the laser main scan start position for each
mode and tray.
Increasing a value: an image is moved to the rear edge of paper.
Decreasing a value: an image is moved to the front edge of paper.
001 By-pass
*ENG
*ENG
*ENG
*ENG
*ENG
006 Duplex
*ENG
32
System SP1-xxx
001 Tray1:Plain:600dpi
*ENG
002 Tray1:Thick1:600dpi
*ENG
003 Tray1:M-Thick:600dpi
*ENG
004 Tray234:Plain:600dpi
*ENG
005 Tray234:Thick1:600dpi
*ENG
006 Tray234:M-Thick:600dpi
*ENG
007 By-pass:Plain:600dpi
*ENG
008 By-pass:Thick1:600dpi
*ENG
009 By-pass:Thick2:600dpi
*ENG
010 By-pass:Thick3:600dpi
*ENG
011 By-pass:M-Thick:600dpi
*ENG
012 Duplex:Plain:600dpi
*ENG
013 Duplex:M-Thick:600dpi
*ENG
014 Tray1:Plain:1200dpi
*ENG
015 Tray1:Thick1:1200dpi
*ENG
016 Tray1:M-Thick:1200dpi
*ENG
017 Tray234:Plain:1200dpi
*ENG
018 Tray234:Thick1:1200dpi
*ENG
019 Tray234:M-Thick:1200dpi
*ENG
020 By-pass:Plain:1200dpi
*ENG
021 By-pass:Thick1:1200dpi
*ENG
022 By-pass:Thick2:1200dpi
*ENG
023 By-pass:Thick3:1200dpi
*ENG
024 By-pass:M-Thick:1200dpi
*ENG
025 Duplex:Plain:1200dpi
*ENG
026 Duplex:M-Thick:1200dpi
*ENG
[5 to 5 / 2 / 1 mm/step]
3
[5 to 5 / 0 / 1 mm/step]
[5 to 5 / 2 / 1 mm/step]
[5 to 5 / 0 / 1 mm/step]
33
1007
001
*ENG
Enables or disables the automatic paper size detection function of the by-pass tray.
This SP determines what paper size the machine detects if the detected size is less than 8.5".
0: LT SEF (default), 1: LG
[Reload Permit Setting] DFU
3
1101
Specifies the settings of the reload permit for cold temperature in color mode. However, these
SPs are desgined for the factory use only. Do not change the adjusted setting.
Destination: NA; North America, TWN; Taiwan, EU; Europe, AA; Asia Pasific
001
002
003
*ENG
[0 to 75 / 50 / 1 deg/step]
*ENG
*ENG
[0 to 200 / 75 / 1 deg/step]
*ENG
[0 to 100 / 20 / 1 deg/step]
004 Specifies the temperature correction of the heating roller (center) when the fusing unit is
determined as cold state.
Temp.:Delta:Cold:End
*ENG
005 Specifies the temperature correction of the heating roller (end) when the fusing unit is
determined as cold state.
Temp.:Delta:Cold: Press
*ENG
[0 to 100 / 0 / 1 deg/step]
006 Specifies the temperature correction of the pressure roller when the fusing unit is determined
as cold state.
Rotation Time:Cold
*ENG
[0 to 200 / 2 / 1 sec/step]
007 Specifies the threshold time for the fusing reload when the fusing unit is determined as cold
state.
34
System SP1-xxx
Temp.:Delta:Warm: Center
*ENG
008 Specifies the temperature correction of the heating roller (center) when the fusing unit is
determined as warm state.
Temp.:Delta:Warm:End
*ENG
009 Specifies the temperature correction of the heating roller (end) when the fusing unit is
determined as warm state.
Temp.:Delta:Warm:Press
*ENG
[0 to 200 / 55 / 1 deg/step]
010 Specifies the temperature correction of the pressure roller when the fusing unit is determined
as warm state.
Time:Warm
*ENG
[0 to 200 / 2 / 1 sec/step]
011 Specifies the threshold time for the fusing reload when the fusing unit is determined as warm
state.
Temp.:Delta:Hot: Center
*ENG
012 Specifies the temperature correction of the heating roller (center) when the fusing unit is
determined as hot state.
Temp.:Delta:Hot:End
*ENG
[0 to 100 / 45 / 1 deg/step]
013 Specifies the temperature correction of the heating roller (end) when the fusing unit is
determined as hot state.
Temp.:Delta:Hot:Press
*ENG
[0 to 200 / 55 / 1 deg/step]
014 Specifies the temperature correction of the pressure roller when the fusing unit is determined
as hot state.
Time:Hot
*ENG
[0 to 200 / 2 / 1 sec/step]
015 Specifies the threshold time for the fusing unit heating when the fusing unit is determined as
hot state.
Temp.:Delta:Cold:BW:Center
*ENG
016 Specifies the temperature correction of the heating roller (center) in the black and white mode
when the fusing unit is determined as cold state.
Temp.:Delta:Cold:BW:End
*ENG
017 Specifies the temperature correction of the heating roller (end) in the black and white mode
when the fusing unit is determined as cold state.
35
Temp.Delta:Cold:BW:Press
*ENG
[0 to 200 / 0 / 1 deg/step]
018 Specifies the temperature correction of the pressure roller in the black and white mode when
the fusing unit is determined as cold state.
Rotation Time:BW:Cold
*ENG
[0 to 200 / 2 / 1 sec/step]
019 Specifies the threshold time for the fusing unit heating in black and white mode when the
fusing unit is determined as cold state.
3
020
Temp.:Delta:Warm:BW:Cent
er
*ENG
[0 to 100 / 10 / 1 deg/step]
Specifies the temperature correction of the heating roller (center) in the black and white mode
when the fusing unit is determined as warm state.
Temp.:Delta:Warm:BW:End
*ENG
[0 to 100 / 45 / 1 deg/step]
021 Specifies the temperature correction of the heating roller (end) in the black and white mode
when the fusing unit is determined as warm state.
Temp.Delta:Warm:BW:Press
*ENG
[0 to 200 / 55 / 1 deg/step]
022 Specifies the temperature correction of the pressure roller in the black and white mode when
the fusing unit is determined as warm state.
Rotation Time:BW:Warm
*ENG
[0 to 200 / 2 / 1 sec/step]
023 Specifies the threshold time for the fusing unit heating in black and white mode when the
fusing unit is determined as warm state.
Temp.:Delta:Hot:BW:Center
*ENG
[0 to 100 / 10 / 1 deg/step]
024 Specifies the temperature correction of the heating roller (center) in the black and white mode
when the fusing unit is determined as hot state.
Temp.:Delta:Hot:BW: End
*ENG
[0 to 100 / 45 / 1 deg/step]
025 Specifies the temperature correction of the heating roller (end) in the black and white mode
when the fusing unit is determined as hot state.
Temp.:Delta:Hot:BW: Press
*ENG
[0 to 200 / 55 / 1 deg/step]
026 Specifies the temperature correction of the pressure roller in the black and white mode when
the fusing unit is determined as hot state.
36
System SP1-xxx
Rotation Time:BW:Hot
*ENG
[0 to 200 / 2 / 1 sec/step]
027 Specifies the threshold time for the fusing unit heating in black and white mode when the
fusing unit is determined as hot state.
030 Flicker Control
*ENG
[0 or 1 / 0 / -]
*ENG
*ENG
*ENG
[0 to 200 / 0 / 1 deg/step]
*ENG
[0 to 200 / 2 / 1 sec/step]
105
Temp.:Delta:Warm:
BW2:Center
*ENG
[0 to 100 / 10 / 1 deg/step]
106
Temp.:Delta:Warm:
BW2:End
*ENG
[0 to 100 / 45 / 1 deg/step]
107
Temp.:Delta:Warm:
BW2:Press
*ENG
[0 to 200 / 55 / 1 deg/step]
*ENG
[0 to 200 / 2 / 1 sec/step]
*ENG
[0 to 100 / 10 / 1 deg/step]
*ENG
[0 to 100 / 45 / 1 deg/step]
*ENG
[0 to 200 / 55 / 1 deg/step]
*ENG
[0 to 200 / 2 / 1 sec/step]
101
109
Temp.:Delta:Cold:
BW2:Center
Temp.:Delta:Hot:
BW2:Center
-001 DFU
to -005 These SPs are desgined for the factory use only. Do not change the adjusted setting.
001 Temp.:Lower Delta:Center
*ENG
*ENG
37
*ENG
*ENG
*ENG
[0 to 200 / 60 / 1 deg/step]
*ENG
[0 to 200 / 0 / 1 sec/step]
-007 DFU
to -011 These SPs are desgined for the factory use only. Do not change the adjusted setting.
Temp.:Lower
Delta:Center:Sp.1
*ENG
*ENG
*ENG
[0 to 50 / 15 / 1 deg/step]
*ENG
[0 to 50 / 15 / 1 deg/step]
*ENG
[0 to 200 / 60 / 1 deg/step]
*ENG
[0 to 200 / 3 / 1 sec/step]
007
Temp.:Upper
Delta:Center:Sp.1
Rotation Time:Sp.1
012 Usage Limitation:
Temp.:Lower
Delta:Center:Sp.2
*ENG
[0 to 100 / 30 / 1 deg/step]
*ENG
[0 to 100 / 30 / 1 deg/step]
*ENG
[0 to 50 / 20 / 1 deg/step]
*ENG
[0 to 50 / 20 / 1 deg/step]
*ENG
[0 to 200 / 60 / 1 deg/step]
*ENG
[0 to 200 / 0 / 1 sec/step]
Temp.:Upper
Delta:Center:Sp.2
-019 DFU
to -024 These SPs are desgined for the factory use only. Do not change the adjusted setting.
38
System SP1-xxx
*ENG
[0 to 200 / 60 / 1 sec/step]
*ENG
[0 to 100 / 25 / 1 deg/step]
*ENG
[0 to 100 / 25 / 1 deg/step]
*ENG
[0 to 50 / 10 / 1 deg/step]
*ENG
[0 to 50 / 10 / 1 deg/step]
*ENG
[0 to 200 / 30 / 1 deg/step]
*ENG
[0 to 200 / 3 / 1 sec/step]
020
Temp.:Lower
Delta:Center:Sp.3
Temp.:Upper
Delta:Center:Sp.3
Rotation Time:Sp3
*ENG
001 Specifies the heating roller target temperature for the ready condition in full color printing.
Usage Limitation:
+5C against the default value for each destination is the upper limit for this setting.
Plain1:FC:Press (DFU)
002
*ENG
[0 to 200 / 95 / 1 deg/step]
Specifies the pressure roller target temperature for the ready condition in full color printing.
DFU:
This SP is desgined for the factory use only. Do not change the adjusted setting.
39
Plain1:BW:Center
*ENG
003 Specifies the heating roller target temperature for the ready condition in BW printing.
Usage Limitation:
+5C against the default value for each destination is the upper limit for this setting.
Plain1:BW:Press (DFU)
004
*ENG
[0 to 200 / 95 / 1 deg/step]
Specifies the pressure roller target temperature for the ready condition in BW printing.
DFU:
This SP is desgined for the factory use only. Do not change the adjusted setting.
Plain2:FC:Center
*ENG
005 Specifies the heating roller target temperature for the ready condition in full color printing.
Usage Limitation:
+5C against the default value for each destination is the upper limit for this setting.
Plain2:FC:Press (DFU)
006
*ENG
[0 to 200 / 95 / 1 deg/step]
Specifies the pressure roller target temperature for the ready condition in full coloe printing.
DFU:
This SP is desgined for the factory use only. Do not change the adjusted setting.
Plain2:BW:Center
*ENG
007 Specifies the heating roller target temperature for the ready condition in BW printing.
Usage Limitation:
+5C against the default value for each destination is the upper limit for this setting.
Plain2:BW:Press (DFU)
008
*ENG
[0 to 200 / 95 / 1 deg/step]
Specifies the pressure roller target temperature for the ready condition in BW printing.
DFU:
This SP is desgined for the factory use only. Do not change the adjusted setting.
Thin:FC:Center
*ENG
System SP1-xxx
*ENG
*ENG
*ENG
*ENG
+10C against the default value is the upper limit for this setting.
014 M-thick:FC:Press (DFU)
M-thick:BW:Center
*ENG
*ENG
*ENG
Thick1:FC:Center
*ENG
*ENG
*ENG
*ENG
Thick2:FC:Center
*ENG
*ENG
41
Thick2:BW:Center
*ENG
*ENG
Thick3:FC:Center
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
Special2:FC:Center
*ENG
*ENG
*ENG
42
System SP1-xxx
*ENG
Special3:FC:Center
*ENG
*ENG
*ENG
+5C against the default value is the upper limit for this setting.
040 Special3:BW:Press (DFU)
Envelop:Center
*ENG
*ENG
*ENG
*ENG
103
Plain1:FC:Press:Low Speed
(DFU)
*ENG
Plain1:BW:Center:Low
Speed
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
104
Plain1:BW:Press:Low Speed
(DFU)
*ENG
Plain2:FC:Center:Low Speed
*ENG
Plain2:FC:Press:Low Speed
(DFU)
*ENG
43
Plain2:BW:Center:Low
Speed
107
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
108
Plain2:BW:Press:Low Speed
(DFU)
*ENG
Thin:FC:Center:Low Speed
*ENG
Thin:FC:Press:Low Speed
(DFU)
*ENG
Thin:BW:Center:Low Speed
*ENG
113
Thin:BW:Press:Low Speed
(DFU)
*ENG
M-Thick:FC:Center:Low
Speed
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
114
115
M-Thick:FC:Press:Low Speed
(DFU)
*ENG
M-Thick:BW:Center:Low
Speed
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
116
44
M-Thick:BW:Press:Low
Speed (DFU)
*ENG
System SP1-xxx
Special1:FC:Center:Low
Speed
117
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
118
119
Special1:FC:Press:Low
Speed (DFU)
*ENG
Special1:BW:Center:Low
Speed
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
120
121
Special1:BW:Press:Low
Speed (DFU)
*ENG
Special2:FC:Center:Low
Speed
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
122
123
Special2:FC:Press:Low
Speed (DFU)
*ENG
Special2:BW:Center:Low
Speed
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
124
125
Special2:BW:Press:Low
Speed (DFU)
*ENG
Special3:FC:Center:Low
Speed
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
126
Special3:FC:Press:Low
Speed (DFU)
*ENG
45
Special3:BW:Center:Low
Speed
127
*ENG
Usage Limitation:
+5C against the default value is the upper limit for this setting.
128
Special3:BW:Press:Low
Speed (DFU)
*ENG
OHP:Center
*ENG
*ENG
*ENG
Envelop:Press:Low Speed
(DFU)
*ENG
Plain1:Grossy:Center
*ENG
*ENG
*ENG
*ENG
*ENG
46
*ENG
System SP1-xxx
Special4:FC:Center
*ENG
*ENG
*ENG
*ENG
Special5:FC:Center
*ENG
*ENG
*ENG
*ENG
Special6:FC:Center
*ENG
*ENG
*ENG
*ENG
*ENG
47
*ENG
*ENG
Envelop:Center:Thick3
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
1106
*ENG
001 Center
002 End
The heating roller has two lamps. One heats the center of the heating roller and the other
heats both ends of the heating roller.
48
System SP1-xxx
*ENG
Specifies the temperature of the heating roller for the ready or energy save 1 mode.
-002 DFU
to -006 These SPs are desgined for the factory use only. Do not change the adjusted setting.
002
003
004
005
006
007
Stanby/Preheat1: Press
[0 to 200 / 0 / 1 deg/step]
Specifies the temperature of the pressure roller for the ready or energy save 1 mode.
Preheat2: Center
*ENG
Specifies the temperature of the heating roller for the energy save 2 mode.
Preheat2:Press
*ENG
[0 to 200 / 0 / 1 deg/step]
Specifies the temperature of the pressure roller for the energy save 2 mode.
Low Power:Center
*ENG
[0 to 200 / 0 / 1 deg/step]
Specifies the temperature of the heating roller for the low power mode.
Low Power:Press
*ENG
[0 to 200 / 0 / 1 deg/step]
Specifies the temperature of the pressure roller for the low power mode.
Print Ready:Center
*ENG
Specifies the temperature of the heating roller for the print ready condition.
Print Ready:Press (DFU)
008
*ENG
*ENG
[0 to 200 / 10 / 1 deg/step]
Specifies the temperature of the pressure roller for the print ready condition.
DFU
This SP is desgined for the factory use only. Do not change the adjusted setting.
49
1108
001
002
*ENG
*ENG
[0 to 200 / 5 / 1 deg/step]
1111
*ENG
[0 to 100 / 17 / 1 deg/step]
001 Specifies the threshold temperature for low temperature. If the fusing temperature is 17C
or less, the machine executes the fusing mode for low temperature.
Temp.: Threshold: High
*ENG
[0 to 100 / 30 / 1 deg/step]
002 Sepcifies the threshold temperature for high temperature. If the fusing temperature is 30C
or more, the machine executes the fusing mode for high temperature.
Low Temp. Correction
*ENG
[0 to 15 / 5 / 1 deg/step]
003 Specifies the additional temperature for the target temperature. If the fusing temperature is
in low temperature condition, this temperature is added to the taraget temperature.
High Temp. Correction
*ENG
[0 to 15 / 0 / 1 deg/step]
004 Specifies the additional temperature for the target temperature. If the fusing temperature is
in high temperature condition, this temperature is added to the taraget temperature.
Job Low Temp. Correction
*ENG
005 Specifies the additional temperature for the target temperature when the environmental
condition is determined as low temperature.
006 Job High Temp. Correction
*ENG
Specifies the additional temperature for the target temperature when the environmental
condition is determined as high temperature.
007 Job Low Temp. Correction:Sp. *ENG
50
System SP1-xxx
008
1112
*ENG
001
*ENG
[-10 to 10 / 0 / 1 /step]
Specifies the subtractive temperature level 1 of the fusing temperature control for variable
job images.
DFU
This SP is desgined for the factory use only. Do not change the adjusted setting.
Temp.:Normal:Center:Level2
002
*ENG
Specifies the subtractive temperature level 2 of the fusing temperature control for variable
job images.
Usage Limitation:
Use 0C or less for this setting.
004
*ENG
[0 to 15 / 5 / 1 deg/step]
*ENG
[0 to 15 / 5 / 1 deg/step]
*ENG
005 Specifies the temperature correction of the paper feeding taraget in the low temperature
condition.
Offset Temp:High
*ENG
[0 to 15 / 5 / 0.1 deg/step]
006 Specifies the temperature correction of the paper feeding taraget in the high temperature
condition.
51
1113
001
[Curl Correction]
Execute Pattern
*ENG
[0 to 2 / 0 / 1 /step]
0: OFF, 1: ON
-002 to
-006, DFU
-008, These SPs are desgined for the factory use only. Do not change the adjusted setting.
-009
Humidity:Threshold:M002 humid
*ENG
[0 to 100 / 65 / 1 %/step]
Humidity:Threshold:H-humid
*ENG
[0 to 100 / 80 / 1 %/step]
Permit Temp.:Delta:Press:M*ENG
004 humid
Specifies the threshold temperature for the curl control in middle humidity.
Permit Temp.:Delta:Press: H*ENG
005 humid
Specifies the threshold temperature for the curl control in high humidity.
[Stand-by Mode Setting]
006 P-Roll Thresh AF Job
*ENG
Specifies the temperature of the pressure roller for the stand-by mode.
CPM:M-humid
*ENG
[0 to 100 / 80 / 1 %/step]
008 Specifies the CPM ratio of the decurl control against to the normal operation in middle
humidity.
009
52
CPM:H-humid
*ENG
[0 to 100 / 65 / 1 %/step]
Specifies the CPM ratio of the decurl control against to the normal operation in high humidity.
System SP1-xxx
1114
001
*ENG
[0 to 200 / 80 / 1 deg/step]
Specifies the threshold temperature of the pressure roller for the heat storage status.
Temp.:Threshold:
002 Atmosphere
*ENG
[0 to 200 / 80 / 1 deg/step]
Specifies the threshold temperature inside the machine for the heat storage feedback control.
1115
001
1116
*ENG
Specifies the different temperature between end and center of the heating roller.
[Press Temp. FB Control]
Execution mode
*ENG
[0 to 2 / 1 / 1 /step]
0: OFF, 1: ON: BW, 2: ON: BW/FC
DFU
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
*ENG
[0 to 500 / 5 / 1 sec/step]
[0 to 20,000 / 0 / 1 msec/step]
Delay:Standard Speed:BW:
*ENG
1
[0 to 20,000 / 0 / 1 msec/step]
022
*ENG
[0 to 20,000 / 0 / 1 msec/step]
*ENG
[0 to 20,000 / 0 / 1 msec/step]
[0 to 20,000 / 0 / 1 msec/step]
53
032
Delay:Standard Speed:BW:
*ENG
2
*ENG
[0 to 20,000 / 0 / 1 msec/step]
*ENG
[0 to 20,000 / 0 / 1 msec/step]
*ENG
[0 to 200 / 0 / 1 deg/step]
[-30 to 0 / -2 / 1 deg/step]
[0 to 30 / 0 / 1 deg/step]
051
Paper Thickness
Coefficient:Plain1
*ENG
[0 to 100 / 20 / 1 /step]
052
Paper Thickness
Coefficient:Plain2
*ENG
[0 to 100 / 20 / 1 /step]
*ENG
[0 to 100 / 0 / 1 /step]
54
[0 to 20,000 / 0 / 1 msec/step]
054
*ENG
[0 to 100 / 0 / 1 /step]
055
Paper Thickness
Coeff.:Thick1
*ENG
[0 to 100 / 0 / 1 /step]
056
Paper Thickness
Coeff.:Thick2
*ENG
[0 to 100 / 0 / 1 /step]
057
Paper Thickness
Coeff.:Thick3
*ENG
[0 to 100 / 0 / 1 /step]
058
Paper Thickness
Coeff.:Special1
*ENG
[0 to 100 / 0 / 1 /step]
059
Paper Thickness
Coeff.:Special2
*ENG
[0 to 100 / 0 / 1 /step]
060
Paper Thicknes
Coeff.:Special3
*ENG
[0 to 100 / 0 / 1 /step]
061
Paper Thickness
Coeff.:Envelop
*ENG
[0 to 100 / 0 / 1 /step]
071
Paper Thickness
Coeff.:Plain1:Low Speed
*ENG
[0 to 100 / 0 / 1 /step]
System SP1-xxx
072
Paper Thickness
Coeff.:Plain2:Low Speed
*ENG
[0 to 100 / 0 / 1 /step]
073
Paper Thickness
Coeff.:Thin:Low Speed
*ENG
[0 to 100 / 0 / 1 /step]
074
*ENG
[0 to 100 / 0 / 1 /step]
075
Paper Thickness
Coeff.:Special1:Low Speed
*ENG
[0 to 100 / 0 / 1 /step]
076
Paper Thickness
Coeff.:Special2:Low Speed
*ENG
[0 to 100 / 0 / 1 /step]
077
Paper Thickness
Coeff.:Special3:Low Speed
*ENG
[0 to 100 / 0 / 1 /step]
078
Paper Thickness
Coeff.:Plain1:Glossy
*ENG
[0 to 100 / 0 / 1 /step]
079
Paper Thickness
Coeff.:Plain2:Glossy
*ENG
[0 to 100 / 0 / 1 /step]
080
*ENG
[0 to 100 / 0 / 1 /step]
*ENG
[0 to 100 / 0 / 1 /step]
Paper Thickness
Coeff.:Envelop:Low Speed
*ENG
[0 to 100 / 0 / 1 /step]
101
Paper Thickness
Coeff.:Special4
*ENG
102
Paper Thickness
Coeff.:Special5
*ENG
103
Paper Thicknes
Coeff.:Special6
*ENG
104
Paper Thickness
Coeff.:Envelop:Thick1
*ENG
[0 to 100 / 0 / 1 /step]
105
Paper Thickness
Coeff.:Envelop:Thick2
*ENG
[0 to 100 / 0 / 1 /step]
55
106
Paper Thickness
Coeff.:Envelop:Thick3
*ENG
[0 to 100 / 0 / 1 /step]
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
*ENG
[0 to 1000 / 1 / 1 sec./step]
*ENG
[0 to 1000 / 29 / 1 sec./step]
003 Temp:Plain:Center1
*ENG
004 Temp:Plain:Press.1
*ENG
005 Temp:Plain:Center2
*ENG
006 Temp:Plain:Press.2
*ENG
007 Temp:M-Thick:Center1
*ENG
[-35 to 35 / 10 / 1C/step]
008 Temp:M-Thick:Press.1
*ENG
[-35 to 35 / 10 / 1C/step]
009 Temp:M-Thick:Center2
*ENG
[-35 to 35 / 10 / 1C/step]
010 Temp:M-Thick:Press.2
*ENG
[-35 to 35 / 10 / 1C/step]
011 Temp:Other:Center1
*ENG
[-35 to 35 / 10 / 1C/step]
012 Temp:Other:Press.1
*ENG
[-35 to 35 / 10 / 1C/step]
013 Temp:Other.Center2
*ENG
[-35 to 35 / 10 / 1C/step]
014 Temp:Other:Press.2
*ENG
[-35 to 35 / 10 / 1C/step]
*ENG
016 Temp:Plain:BW:End1
*ENG
017 Temp:Plain:Center2
*ENG
018 Temp:Plain:BW:End2
*ENG
*ENG
[-35 to 35 / 20 / 1C/step]
*ENG
[-35 to 35 / 20 / 1C/step]
019
Temp:Other:Center1:LowSpee
d
020 Temp:Other:End1:LowSpeed
56
System SP1-xxx
021
Temp:Other.Center2:LowSpee
d
*ENG
[-35 to 35 / 20 / 1C/step]
022 Temp:Other:End2:LowSpeed
*ENG
[-35 to 35 / 20 / 1C/step]
023 Temp:Envelop:Center1
*ENG
[-35 to 35 / 15 / 1C/step]
024 Temp:Envelop:End1
*ENG
[-35 to 35 / 15 / 1C/step]
025 Temp:Envelop:Center2
*ENG
026 Temp:Envelop:End2
*ENG
[-35 to 35 / 15 / 1C/step]
1121
[Switch:Rotation Start/Stop]
*ENG
DFU
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
*ENG
[0 to 100 / 10 / 1 sec./step]
*ENG
[0 to 100 / 10 / 1 sec./step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 100 / 10 / 1 sec./step]
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
*ENG
[0 to 240 / 60 / 1 min./step]
57
*ENG
DFU
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
*ENG
Specifies the CPM down threshold temperature for the low temperature condition. If the fusing
temperature decreases -20C (adjustable) below the target temperature, the machine enters
the CPM down mode.
002 Low:Up Temp.
*ENG
Specifies the CPM up threshold temperature for the low temperature condition. If the fusing
temperature increases -15C (adjustable) below the target temperature, the machine enters
the CPM up mode.
003 Low :1st CPM
*ENG
Specifies the 1st CPM down ration against the normal CPM in the low temperature condition.
004 Low :2nd CPM
*ENG
Specifies the 2nd CPM down ration against the normal CPM in the low temperature condition.
005 Low :3rd CPM
*ENG
Specifies the 3rd CPM down ration against the normal CPM in the low temperature condition.
006 High :1st CPM
*ENG
Specifies the 1st CPM down ration against the normal CPM in the high temperature condition.
007 High:2nd CPM
*ENG
Specifies the 3rd CPM down ration against the normal CPM in the high temperature condition.
008 High:3rd CPM
*ENG
Specifies the 1st CPM down ration against the normal CPM in the high temperature condition.
009
58
*ENG
System SP1-xxx
Specifies the heating roller temperature for 1st CPM down of A3 paper size.
010
*ENG
Specifies the heating roller temperature for 2nd CPM down of A3 paper size.
011
*ENG
Specifies the heating roller temperature for 3rd CPM down of A3 paper size.
012
*ENG
Specifies the heating roller temperature for 1st CPM down of A4 paper size.
013
*ENG
Specifies the heating roller temperature for 2nd CPM down of A4 paper size.
014
*ENG
Specifies the heating roller temperature for 3rd CPM down of A4 paper size.
015
*ENG
Specifies the pressure roller temperature for 1st CPM down of B5 paper size.
016
*ENG
Specifies the pressure roller temperature for 2nd CPM down of B5 paper size.
017
*ENG
Specifies the pressure roller temperature for 3rd CPM down of B5 paper size.
018
*ENG
Specifies the pressure roller temperature for 1st CPM down of A5 paper size.
019
*ENG
59
Specifies the pressure roller temperature for 2nd CPM down of A5 paper size.
020
*ENG
Specifies the pressure roller temperature for 3rd CPM down of A5 paper size.
021
*ENG
Specifies the pressure roller temperature for 1st CPM down of A6 paper size.
022
*ENG
Specifies the pressure roller temperature for 2nd CPM down of A6 paper size.
023
*ENG
Specifies the pressure roller temperature for 3rd CPM down of A6 paper size.
024
*ENG
[1 to 250 / 10 / 1 sec/step]
025
*ENG
026
*ENG
027
*ENG
028
*ENG
029
*ENG
030
*ENG
1131
60
Judging Interval
System SP1-xxx
[0 to 2 / 0 / 1 /step]
001 Feed Permit Condition
*ENG
2: Paper feed permission is done when changing the paper size from smaller one to larger
one and changing the copy/print mode from duplex mode to simplex mode.
[Maximum Duty Switch]
1132
DFU
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
*ENG
[0 or 1 / 1 / 1 /step]
0: FIXED, 1: CONTROL
[PowerControl]
Power Offset
[Voltage Detection]
Temp.:Threshold Value
*ENG
[-4 to 4 / 0 / 1 /step]
*ENG
[0 to 350 / 0 / 1 V/step]
*ENG
[0 to 200 / 80 / 1C/step]
001
DFU
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
Heater OFF Time: Normal
Speed: FC
*ENG
61
002
*ENG
005
*ENG
006
*ENG
007
DFU
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
001 SC Number
SC Cause
*ENG
*ENG
[0 to 9 / - / 1/step]
104
105
106
107
108
62
*ENG
Displays the calculated temperature at the center of the heating roller when an SC was issued.
Htg Roller:End Diff1
*ENG
Displays the calculated temperature at the end of the heating roller when an SC was issued.
Htg Roller:End Det1
*ENG
Displays the detected temperature at the end of the heating roller when an SC was issued.
Htg Roller:End Corr1
*ENG
Displays the ambient temperature at the end of the heating roller when an SC was issued.
Press Roller Temp Value1
*ENG
*ENG
Displays the temperature at the end of the pressure roller when an SC was issued.
System SP1-xxx
151
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
201
*ENG
3
[-20 to 260 / - / 1 deg/step]
SPs from -201 to -207 show fusing SC information before previous fusing SC.
*ENG
*ENG
*ENG
*ENG
*ENG
DFU
This SP is desgined for the factory use only. Do not change the adjusted setting.
001
SC Display
*ENG
[0 or 1 / 0 / -]
0: ON, 1: OFF
DFU
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
63
Execute
001 Executes the nip band measurement between heating roller and pressure roller.
If the nip band width is not 8 mm, and fusing is not good, replace the pressure roller or install
a new fusing unit.
002
003
004
Pre-Idling Time
*ENG
* ENG
[0 to 100 / 20 / 1 sec/step]
* ENG
Specifies the feeding time from the tray to the fusing unit at the fusing nip band check.
[Low Temp. Start Up]
1153
001
002
003
005
010
64
DFU
The following SPs below are desgined for the factory use only. Do not change the adjusted
setting.
Temp.:Threshold Value1
* ENG
Sepcifies the threshold temperature 1 for the warming up in the low temperature condition.
Temp.:Threshold Value2
* ENG
Sepcifies the threshold temperature 2 for the warming up in the low temperature condition.
Temp.:Target
* ENG
Sepcifies the target temperature for the warming up in the low temperature condition.
Temp.: Rotation Threshold
Value1
* ENG
Sepcifies the threshold temperature 1 for the warming up rotation in the low temperature
condition.
Time:Heat Storage Devision1 * ENG
[0 to 250 / 60 / 1 sec./step]
Sepcifies the execution time 1 for the warming up in the low temperature condition.
System SP1-xxx
011
1801
[0 to 250 / 30 / 1 sec../step]
Sepcifies the execution time 2 for the warming up in the low temperature condition.
[Motor Speed Adjust]
*ENG
*ENG
003 Bk OpcDevMot:120
*ENG
004 Bk OpcDevMot:60:Thick
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[4 to 4 / 0 / 0.01 %/step]
010 TransferMot:60:Thick
*ENG
[4 to 4 / 0 / 0.01 %/step]
011 Feed1:CW60:Thick
*ENG
012 Feed1:CW120
*ENG
013 Feed1:CCW60:Thick
*ENG
014 Feed1:CCW120
*ENG
015 Feed12:CW60:Thick
*ENG
016 Feed12:CW120
*ENG
017 Feed12:CCW60:Thick
*ENG
018 Feed12:CCW120
*ENG
019 By-pass:60:Thick
*ENG
020 By-pass:120
*ENG
[15 to 15 / 0 / 1 %/step]
65
66
021 Inverter:CW60:Thick
*ENG
022 Inverter:CW120
*ENG
023 Inverter:CCW60:Thick
*ENG
024 Inverter:CCW120
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[2 to 2 / 0 / 0.05 %/step]
*ENG
[0 to 1 / 1 /1]
031 Offset:120:Color
*ENG
032 Offset:60:Color
*ENG
*ENG
034 Feed1:CW60:1200dpi
*ENG
035 Feed1:CCW60:1200dpi
*ENG
036 Feed2:CW60:1200dpi
*ENG
037 Feed2:CCW60:1200dpi
*ENG
038 By-pass:60:1200dpi
*ENG
039 Inverter:CW60:1200dpi
*ENG
040 Inverter:CCW60:1200dpi
*ENG
041 FusingMot:60:1200dpi
*ENG
042 BkOpcDevMot:60:1200dpi
*ENG
043 TransferMot:60:1200dpi
*ENG
[4 to 4 / 0 / 0.01 %/step]
[2 to 2 / 0 / 0.05 %/step]
[-7 to 7 / 0 /1step]
[4 to 4 / 0.3 / 0.05 %/step]
[2 to 2 / 0 / 0.05 %/step]
System SP1-xxx
1803
These SPs can adjust the sub-scan magnification error. However, first read the "Sub-scan
Magnification Error" in the "Troubleshooting Guide" (Main Chapters) to execute these SPs.
NEVER EXECUTE these SPs before reading the "Sub-scan Magnification Error". Otherwise,
color registration errors occur on outputs and this cannot be recovered by the line position
adjustment.
001 Plain:600dpi:input
*ENG
002 Plain:1200dpi:input
*ENG
003 Thick:input
*ENG
004 Plain:600dpi:result
*ENG
005 Plain:1200dpi:result
*ENG
006 Thick:result
*ENG
1902
[0 to 1 / 0 / 1 /step]
0: Success, 1: Failure
001 Execute
[0 or 1 / 0 / 1]
002 Result
*ENG
0: Successfully done
2: Sampling failure
3: Insufficient detection number
[0 or 1 / 1 / 1]
*ENG
1907
*ENG
[10 to 10 / 0 / 1 mm/step]
67
*ENG
*ENG
1950
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
1951
[10 to 10 / 0 / 1 mm/step]
[0 to 600 / 0 / 1sec/step]
*ENG
*ENG
004
*ENG
*ENG
*ENG
*ENG
1952
[0 to 900 / 0 / 1 sec/step]
001 -
68
*ENG
*ENG
[0 to 60 / 0 / 1 min./step]
System SP1-xxx
1953
001
*ENG
[0 or 1 / 0 / 1 /step]
0: Off, 1: On
Time: Threshold
*ENG
[0 to 60 / 60 / 1 min./step]
*ENG
[0 to 999999999 / 0 / 1 mm/step]
*ENG
Time
*ENG
[0 to 7200 / 0 / 1 sec./step:
005
*ENG
*ENG
*ENG
*ENG
[0 to 7200 / 1 / 1 sec./step]
*ENG
*ENG
*ENG
*ENG
009
1954
69
*ENG
*ENG
*ENG
70
*ENG
*ENG
*ENG
*ENG
*ENG
004
System SP2xxx
System SP2xxx
SP2-XXX (Drum)
[Charge DC V:Fixed] DFU
2005
Charge bias (DC component) is automatically adjusted during process control; therefore,
adjusting these settings does not effect while process control mode (SP3-041-1 Default: ON)
is activated. When deactivating process control mode with SP3-041-1, the values in these
SP modes are used for printing.
001 Plain: Bk
*ENG
002 Plain: C
*ENG
003 Plain: M
*ENG
004 Plain: Y
*ENG
*ENG
*ENG
*ENG
*ENG
71
001 Plain: Bk
*ENG
002 Plain: C
*ENG
003 Plain: M
*ENG
004 Plain: Y
*ENG
*ENG
*ENG
*ENG
*ENG
(Color)
Displays/sets the AC current target of the charge roller for LL environment (Low temperature
and Low humidity).
*ENG
*ENG
*ENG
*ENG
72
*ENG
*ENG
*ENG
*ENG
System SP2xxx
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
2012
73
*ENG
0: Process control
1: Manual control (AC voltages are decided
with SP2006.)
2013
[Envir. Correct:PCU]
*ENG
*ENG
[0 to 5 / 0 / 1 /step]
0: The environmental condition is determined
automatically.
1: LL, 2: ML, 3: MM, 4: MH, 5: HH
*ENG
*ENG
*ENG
*ENG
74
System SP2xxx
*ENG
*ENG
*ENG
*ENG
[1 to 5 / / 1 /step]
1: LL, 2: ML, 3: MM, 4: MH, 5: HH
011 Previous Temp.: Display
*ENG
*ENG
*ENG
2014
*ENG
*ENG
*ENG
[0 to 500 / 10 / 1 page/step]
*ENG
[0 to 99 / 25 / 1 deg/step]
*ENG
[0 to 99 / 50 / 1 %RH/step]
*ENG
[0 to 99 / 12 / 1 g/m3/step]
*ENG
[0 to 99 / 10 / 1 deg/step]
*ENG
[0 to 99 / 50 / 1 %RH/step]
*ENG
[0 to 99 / 6 / 1 g/m3/step]
*ENG
[0 to 20 / 1 / 0.1 deg/step]
75
*ENG
[0 to 50 / 5 / 1 %RH/step]
*ENG
[0 to 20 / 1 / 0.1 g/m3/step]
*ENG
*ENG
[0 to 2 / 1 / 0.01 kV/mA/step]
2015
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 Y
*ENG
2016
[0 to 9 / 0 / 1 /step]
*ENG
[0 to 50 / 15 / 1 deg/step]
001 Specifies the threshold temperature for the low temperature mode of the drum lubrication
during the multiple printing job.
Execution Interval: Setting:1
*ENG
[0 to 999 / 0 / 1 page/step]
002 Specifies the reference number of the outputs for the high coverage image job in the low
speed mode.
Execution Interval: Setting:2
*ENG
[0 to 999 / 0 / 1 page/step]
003 Specifies the reference number of the outputs for the high coverage image printing job in the
low temperature condition.
004
*ENG
[0 to 999 / 0 / 1 page/step]
Specifies the reference number of the outputs for the low coverage image job.
High Coverage Threshold:1
*ENG
[0 to 100 / 10 / 0.01%/step]
005 Specifies the threshold for the high coverage image to the drum lubrication mode handled
by the setting 1 (SP2-016-002).
76
System SP2xxx
*ENG
[0 to 100 / 20 / 0.01%/step]
006 Specifies the threshold for the high coverage image to the drum lubrication mode handled
by the setting 2 (SP2-016-003).
High Coverage Threshold:3
*ENG
007 Specifies the threshold for the low coverage image to the drum lubrication mode handled
by the setting 3 (SP2-016-004).
008
009
010
011
012
013
014
Application Time:1
*ENG
[0 to 99 / 0 / 1 sec./step]
Specifies the execution time for the drum lubrication mode of the setting 1 (SP2-016-002).
Application Time:2
*ENG
[0 to 99 / 0 / 1 sec./step]
Specifies the execution time for the drum lubrication mode of the setting 2 (SP2-016-003).
Application Time:3
*ENG
[0 to 99 / 0 / 1 sec./step]
Specifies the execution time for the drum lubrication mode of the setting 3 (SP2-016-004).
Average Coverage:1:K
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
77
*ENG
*ENG
Mode Counter:K
*ENG
[0 to 999 / - / 1 page/step]
023
024
Displays the black print counter after the previous drum lubrication.
Mode Counter:CMY
*ENG
Displays the color print counter after the previous drum lubrication.
[Color Regist Adjust]
2101
These values are the parameters for the automatic line position adjustment and are adjusted
at the factory. However, you must input a value for SP2101-001 after replacing the laser
optics housing unit. For details, see "Laser Optics Housing Unit" in the "Replacement and
Adjustment" section. The value should be provided with the new laser optics housing unit.
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[Magnification Adjust]
2102
78
These values are the parameters for the automatic line position adjustment and are adjusted
at the factory. These SPs must be input only when a new laser unit is installed.
System SP2xxx
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
2103
*ENG
*ENG
003 Left
*ENG
004 Right
*ENG
*ENG
[0 to 4 / 1 / 0.1 mm/step]
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 4 / 1 / 0.1 mm/step]
*ENG
*ENG
*ENG
*ENG
79
2104
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 Y
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
2106
001 Warming-Up
*ENG
[0 to 60 / 10 / 1 sec/step]
*ENG
[0 to 60 / 0 / 1 sec/step]
2107
80
*ENG
[Image Parameter]
DFU
System SP2xxx
*ENG
*ENG
2109
[0 or 1 / 1 / 1 /step]
[Test Pattern]
Generates the test pattern using "COPY Window" tab in the LCD.
Pattern Selection
[0 to 23 / 0 / 1/step]
0 None
1: Vertical Line (1dot)
3: Horizontal (1dot)
4: Horizontal (2dot)
[1 to 4 / 1 / 1/step]
1: All colors, 2: Magenta, 3: Yellow, 4: Cyan
006 Density: Bk
007 Density: C
[0 to 15 / 15 / 1 /step]
008 Density: M
0: Lightest density
009 Density: Y
2111
81
003 Execute:Mode c
2112
001 Execute
[Skew Adjustment]
2117
001 Pulse: C
*ENG
002 Pulse: M
*ENG
003 Pulse: Y
*ENG
2118
82
[Skew Adjustment]
001 Execute: C
*ENG
002 Execute: M
*ENG
003 Execute: Y
*ENG
2119
[75 to 75 / 0 / 1 pulse/step]
System SP2xxx
001 C
*ENG
002 M
*ENG
003 Y
*ENG
[75 to 75 / 0 / 1 pulse/step]
[P-Sensor Test]
2140
001 PWM
*ENG
[TM-Sensor Test]
005 PWM: Front
*ENG
*ENG
*ENG
[0 to 1024 / 0 / 1/step]
[P-Sensor Test]
2141
001 Average
*ENG
[TM-Sensor Test]
005 Average: Front
*ENG
*ENG
*ENG
[0 to 5.5 / 0 / 0.01V/step]
[P-Sensor Test]
2142
83
001 Maximum
*ENG
[TM-Sensor Test]
005 Maximum: Front
*ENG
*ENG
*ENG
[0 to 5.5 / 0 / 0.01V/step]
[P-Sensor Test]
2143
001 Minimum
*ENG
[TM-Sensor Test]
005 Minimum: Front
*ENG
*ENG
*ENG
[0 to 5.5 / 0 / 0.01V/step]
[P-Sensor Test]
2144
001 Maximum 2:
*ENG
[TM-Sensor Test]
84
*ENG
*ENG
*ENG
[0 to 5.5 / 0 / 0.01V/step]
System SP2xxx
[P-Sensor Test]
2145
001 Minimum 2
*ENG
[TM-Sensor Test]
005 Minimum 2: Front
*ENG
*ENG
*ENG
[0 to 5.5 / 0 / 0.01V/step]
2150
Adjusts the magnification for each area. The main scan (297 mm) is divided into 8 areas.
Area 1 is at the front side of the machine (left side of the image) and area 8 is at the rear
side of the machine (right side of the image).
Decreasing a value makes the image shift to the left side on the print.
Increasing a value makes the image shift to the right side on the print.
1 pulse = 1/16 dot
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
079 C: Area0
*ENG
85
86
080 C: Area1
*ENG
081 C: Area2
*ENG
082 C: Area3
*ENG
083 C: Area4
*ENG
084 C: Area5
*ENG
085 C: Area6
*ENG
086 C: Area7
*ENG
087 C: Area8
*ENG
131 M: Area0
*ENG
132 M: Area1
*ENG
133 M: Area2
*ENG
134 M: Area3
*ENG
135 M: Area4
*ENG
136 M: Area5
*ENG
137 M: Area6
*ENG
138 M: Area7
*ENG
139 M: Area8
*ENG
183 Y: Area0
*ENG
184 Y: Area1
*ENG
185 Y: Area2
*ENG
186 Y: Area3
*ENG
187 Y: Area4
*ENG
188 Y: Area5
*ENG
189 Y: Area6
*ENG
190 Y: Area7
*ENG
191 Y: Area8
*ENG
System SP2xxx
The main scan is divided into 16 areas. However, the image areas are limited from area 1
to area 14.
For BK and Magenta, area 1 is at the rear side of the machine (left side of the image) and
area 14 is at the front side of the machine (right side of the image).
For Cyan and Yellow, area 1 is at the front side of the machine (right side of the image) and
area 14 is at the rear side of the machine (left side of the image).
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
87
88
033 C: Area 0
*ENG
034 C: Area 1
*ENG
035 C: Area 2
*ENG
036 C: Area 3
*ENG
037 C: Area 4
*ENG
038 C: Area 5
*ENG
039 C: Area 6
*ENG
040 C: Area 7
*ENG
041 C: Area 8
*ENG
042 C: Area 9
*ENG
043 C: Area 10
*ENG
044 C: Area 11
*ENG
045 C: Area 12
*ENG
046 C: Area 13
*ENG
047 C: Area 14
*ENG
048 C: Area 15
*ENG
065 M: Area 0
*ENG
System SP2xxx
066 M: Area 1
*ENG
067 M: Area 2
*ENG
068 M: Area 3
*ENG
069 M: Area 4
*ENG
070 M: Area 5
*ENG
071 M: Area 6
*ENG
072 M: Area 7
*ENG
073 M: Area 8
*ENG
074 M: Area 9
*ENG
075 M: Area 10
*ENG
076 M: Area 11
*ENG
077 M: Area 12
*ENG
078 M: Area 13
*ENG
079 M: Area 14
*ENG
080 M: Area 15
*ENG
097 Y: Area 0
*ENG
3
[50 to 150 / 100 / 1 %/step]
89
098 Y: Area 1
*ENG
099 Y: Area 2
*ENG
100 Y: Area 3
*ENG
101 Y: Area 4
*ENG
102 Y: Area 5
*ENG
103 Y: Area 6
*ENG
104 Y: Area 7
*ENG
105 Y: Area 8
*ENG
106 Y: Area 9
*ENG
107 Y: Area 10
*ENG
108 Y: Area 11
*ENG
109 Y: Area 12
*ENG
110 Y: Area 13
*ENG
111 Y: Area 14
*ENG
112 Y: Area 15
*ENG
2160
90
001 600dpi:Bk
*ENG
002 600dpi:C
*ENG
003 600dpi:M
*ENG
004 600dpi:Y
*ENG
005 1200dpi:Bk
*ENG
006 1200dpi:C
*ENG
007 1200dpi:M
*ENG
008 1200dpi:Y
*ENG
[10 to 15 / 15 / 1 /step]
System SP2xxx
009 600dpi:Indet.:Bk
*ENG
010 1200dpi:Indet.:Bk
*ENG
600dpi:Multivalued:Bk
011
(2bit)
*ENG
2180
[10 to 15 / 15 / 1 /step]
2181
*ENG
*ENG
91
92
003 Skew: C
*ENG
004 Bent: C
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[15 to 15 / 0 / 1 pulse/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[1 to 1 / 0 / 0.001 line/step]
*ENG
*ENG
[1 to 1 / 0 / 0.001 line/step]
021 Skew: M
*ENG
022 Bent: M
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
System SP2xxx
*ENG
*ENG
[15 to 15 / 0 / 1 pulse/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[1 to 1 / 0 / 0.001 line/step]
*ENG
*ENG
[1 to 1 / 0 / 0.001 line/step]
039 Skew: Y
*ENG
040 Bent: Y
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[15 to 15 / 0 / 1 pulse/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[1 to 1 / 0 / 0.001 line/step]
93
*ENG
*ENG
[1 to 1 / 0 / 0.001 line/step]
*ENG
[1 to 1 / 0 / 0.001 line/step]
*ENG
[7 to 7 / 0 / 1 /step]
*ENG
[1 to 1 / 0 / 0.001 line/step]
*ENG
[7 to 7 / 0 / 1 /step]
001 C Magnification
*ENG
002 M Magnification
*ENG
003 Y Magnification
*ENG
94
*ENG
*ENG
[-15 to 15 / 0 / 1 pulse/step]
*ENG
*ENG
[-15 to 15 / 0 / 1 pulse/step]
*ENG
*ENG
[-15 to 15 / 0 / 1 pulse/step]
*ENG
*ENG
[-15 to 15 / 0 / 1 pulse/step]
*ENG
*ENG
[-15 to 15 / 0 / 1 pulse/step]
System SP2xxx
*ENG
*ENG
[-15 to 15 / 0 / 1 pulse/step]
*ENG
*ENG
[1 to 1 / 0 / 0.001 /line]
*ENG
*ENG
[1 to 1 / 0 / 0.001 /line]
*ENG
*ENG
[1 to 1 / 0 / 0.001 /line]
*ENG
*ENG
[1 to 1 / 0 / 0.001 /line]
*ENG
*ENG
[1 to 1 / 0 / 0.001 /line]
*ENG
*ENG
[1 to 1 / 0 / 0.001 /line]
040 C:Skew
*ENG
041 M:Skew
*ENG
042 Y:Skew
*ENG
2190
[-50 to 50 / 0 / 1 m]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 or 1 / 1 / 1 boolean/step]
[0 or 1 / 1 / 1 boolean /step]
0: Disable correction
1: Enable correction
95
*ENG
*ENG
*ENG
[0 or 1 / 1 / 1 boolean /step]
[0 or 1 / 0 / 1 boolean /step]
*ENG
*ENG
0: Adjusted with Bk
1: Adjusted in minimum shift among four
colors
[0 to 3500 / 200 / 1 m/step]
96
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
System SP2xxx
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 3 / 3 / 1/step]
97
001 ch 0: 1st
*ENG
002 ch 0: 2nd
*ENG
003 ch 0: 3rd
*ENG
004 ch 0: 4th
*ENG
005 ch 1: 1st
*ENG
006 ch 1: 2nd
*ENG
007 ch 1: 3rd
*ENG
008 ch 1: 4th
*ENG
009 ch 2: 1st
*ENG
010 ch 2: 2nd
*ENG
011 ch 2: 3rd
*ENG
012 ch 2: 4th
*ENG
2193
001
*ENG
[0 or 1 / 1 / 1 ] 0: OFF, 1: ON
*ENG
002 Adjusts the threshold of the line position adjustment for BW and color printing mode after
job end.
003
*ENG
Adjusts the threshold of the line position adjustment for color printing mode after job end.
Page: Interrupt: BW+FC
*ENG
004 Adjusts the threshold of the line position adjustment for BW and color printing mode during
job.
005
98
Page: Interrupt: FC
*ENG
Adjusts the threshold of the line position adjustment for color printing mode during jobs.
System SP2xxx
Page: Standby: BW + FC
*ENG
Adjusts the threshold of the line position adjustment for BW printing mode in stand-by mode.
006 The line position adjustment is done when the number of outputs in BW printing mode reaches
the value specified with this SP and the condition of SP2-193-008 or SP2-193-009 is
satisfied.
Page: Standby: FC
*ENG
Adjusts the threshold of the line position adjustment for BW printing mode in stand-by mode.
007 The line position adjustment is done when the number of outputs in color printing mode
reaches the value specified with this SP and the condition of SP2-193-008 or SP2-193-009
is satisfied.
Temp Change
*ENG
[0 to 100 / 5 / 1deg/step]
008 Adjust the temperature change threshold for the line position adjustment (Mode b: adjustment
once). The timing for line position adjustment depends on the combinations of several
conditions. Section Descriptions" section.
Elapse Time
*ENG
009 Adjust the time threshold for the line position adjustment (Mode b: adjustment once). The
timing for line position adjustment depends on the combinations of several conditions.
Temp Change 2
*ENG
[0 to 100 / 10 / 1deg/step]
011 Adjust the temperature change threshold for the line position adjustment (Mode a: adjustment
twice). The timing for line position adjustment depends on the combinations of several
conditions.
016 Page: Power ON:BW+FC
2194
*ENG
001 Year
*ENG
[0 to 99 / 0 / 1 year/step]
002 Month
*ENG
[1 to 12 / 1 / 1 month/step]
003 Date
*ENG
[1 to 31 / 1 / 1 day/step]
004 Hour
*ENG
[0 to 23 / 0 / 1 hour/step]
005 Minute
*ENG
[0 to 59 / 0 / 1 minute/step]
006 Temperature
*ENG
[0 to 100 / 0 / 1 deg/step]
99
[0 or 1 / 0 / 1 /step]
*ENG
*ENG
[0 to 999999 / 0 / 1 times/step]
*ENG
[0 to 999999 / 0 / 1 times/step]
*ENG
[0 to 9 / 0 / 1 /step]
*ENG
0: Not done
1: Completed successfully
2: Cannot detect patterns
*ENG
2197
*ENG
[10 to 40 / 20 / 10 ms/step]
*ENG
*ENG
*ENG
2198
Resets the value of the skew adjustment motor for each color.
These SPs must be executed when a new laser optics housing unit is installed. For details,
see "Laser Unit" in the "Replacement and Adjustment" section.
100
*ENG
*ENG
*ENG
System SP2xxx
Adjusts the fixed LD power for each line speed and color.
These SPs are activated only when SP3-041-002 is set to "0".
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
Development bias is automatically adjusted during process control; therefore, adjusting these
settings has no effect while Process Control (SP3-041-001 Default: ON) is activated.
After deactivating Process Control with SP3-041-001, the values in these SP modes are used
for printing.
Normal: 120 mm/sec, Low: 60 mm/sec
101
001 Plain: Bk
*ENG
002 Plain: M
*ENG
003 Plain: C
*ENG
004 Plain: Y
*ENG
009 Thick 2: Bk
*ENG
010 Thick 2: M
*ENG
011 Thick 2: C
*ENG
012 Thick 2: Y
*ENG
2241
[Ambient Temp/Hum:Display]
Displays the environment temperature and humidity.
001 Temperature
[5 to 45 / - / 0.1deg/step]
2302
*ENG
[0 to 6 / 0 / 1 /step]
102
*ENG
System SP2xxx
004
005
006
*ENG
*ENG
*ENG
*ENG
[5 to 30 / 5 / 1 deg/step]
007 Adjusts the threshold temperature for SLL. If detected temperature is less than a value specified
by this SP, SLL condition is determined regardless of humidity.
2308
001 Threshold 1
*ENG
002 Threshold 2
*ENG
003 Threshold 3
*ENG
004 Threshold 4
*ENG
2311
103
*ENG
*ENG
2316
001
2326
001
*ENG
[0 to 60 / 5 / 1 A /step]
Adjusts the bias of the image transfer roller at power-on or a closed cover.
[Transfer Roller CL: Bias] DFU
Transfer Roller Cleaning: Bias Adjustment
Positive:befor and after JOB
*ENG
Adjusts the positive voltage of the paper transfer roller for cleaning the paper transfer roller.
*ENG
Adjusts the negative current of the paper transfer roller for cleaning the paper transfer roller.
Positive:after JAM
*ENG
003 Adjusts the negative current limit of the paper transfer roller for cleaning the paper transfer
roller.
004 Negative:after JAM
*ENG
001
104
*ENG
[0 to 60 / 25 / 1 A]
Adjusts the current for the image transfer belt in B/W mode for plain paper.
System SP2xxx
003
*ENG
[0 to 60 / 13 / 1 A]
Adjusts the current for the image transfer belt in B/W mode for thick 1 paper.
[Common: FC: Bias] DFU
2357
001
002
003
004
009
010
011
012
2360
*ENG
[0 to 60 / 23 / 1 A]
Adjusts the current for the image transfer belt for Black in full color mode for plain paper.
Image Transfer:: Normal Spd:C
*ENG
[0 to 60 / 22 / 1 A]
Adjusts the current for the image transfer belt for Magenta in full color mode for plain paper.
Image Transfer: Normal Spd:M
*ENG
[0 to 60 / 25 / 1 A]
Adjusts the current for the image transfer belt for Cyan in full color mode for plain paper.
Image Transfer: Normal Spd:Y
*ENG
[0 to 60 / 29 / 1 A]
Adjusts the current for the image transfer belt for Yellow in full color mode for plain paper.
Image Transfer: Low Speed:Bk
*ENG
[0 to 60 / 13 / 1 A]
Adjusts the current for the image transfer belt for Black in full color mode for thick 1 paper.
Image Transfer: Low Speed:C
*ENG
[0 to 60 / 12 / 1 A]
Adjusts the current for the image transfer belt for Magenta in full color mode for thick 1 paper.
Image Transfer: Low Speed:M
*ENG
[0 to 60 / 13 / 1 A]
Adjusts the current for the image transfer belt for Cyan in full color mode for thick 1 paper.
Image Transfer: Low Speed:Y
*ENG
[0 to 60 / 14 / 1 A]
Adjusts the current for the image transfer belt for Yellow in full color mode for thick 1 paper.
[Common: BW Env. Correction Table] DFU
*ENG
[1 to 50 / 42 / 1 /step]
*ENG
[1 to 50 / 38 / 1 /step]
105
*ENG
[1 to 50 / 25 / 1 /step]
*ENG
[1 to 50 / 46 / 1 /step]
*ENG
[1 to 50 / 43 / 1 /step]
*ENG
[1 to 50 / 45 / 1 /step]
*ENG
[1 to 50 / 26 / 1 /step]
*ENG
*ENG
*ENG
[1 to 50 / 38 / 1 /step]
[1 to 50 / 45 / 1 /step]
Adjusts the current for the paper transfer roller for plain paper in black-and-white mode.
Normal: 120 mm/sec, Low: 60mm/sec
*ENG
[0 to 200 / 20 / 1 A /step]
*ENG
[0 to 200 / 23 / 1 A /step]
*ENG
*ENG
[0 to 200 / 12 / 1 A /step]
Adjusts the current for the paper transfer roller for plain paper in full color mode.
Normal: 120 mm/sec, Low: 60mm/sec
106
*ENG
[0 to 200 / 23 / 1 A /step]
*ENG
[0 to 200 / 28 / 1 A /step]
*ENG
[0 to 200 / 13 / 1 A /step]
*ENG
[0 to 200 / 14 / 1 A /step]
System SP2xxx
[Plain-T:SizeCorrect:BW]
2411
Adjusts the size correction coefficient for the paper transfer roller current for each paper size.
SP2403 and SP2407 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60mm/sec
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
107
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[Plain-T:SizeCorrect:FC]
2412
Adjusts the size correction coefficient for the paper transfer roller current for each paper size.
SP2403 and SP2407 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60mm/sec
108
System SP2xxx
*ENG
*ENG
*ENG
*ENG
[100 to 4000 / 130 / 5%/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
109
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[Pain-T:Size-Env.Correct:BW] DFU
2413
Adjusts the size correction coefficient table for the paper transfer roller current for each paper
size. SP2403 and SP2407 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
*ENG
[1 to 50 / 30 / 1/step]
*ENG
*ENG
[1 to 50 / 23 / 1/step]
110
*ENG
System SP2xxx
[1 to 50 / 9 / 1/step]
006 Paper Transfer: Normal: 2nd: S2
*ENG
*ENG
*ENG
[1 to 50 / 10 / 1/step]
009 Paper Transfer: Normal: 1st: S3
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
111
[1 to 50 / 13 / 1/step]
*ENG
*ENG
*ENG
*ENG
*ENG
[Pain-T:Size-Env.Correct:FC] DFU
2414
Adjusts the size correction coefficient table for the paper transfer roller current for each paper
size. SP2403 and SP2407 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
*ENG
[1 to 50 / 30 / 1/step]
*ENG
*ENG
[1 to 50 / 37 / 1/step]
*ENG
*ENG
112
*ENG
System SP2xxx
[1 to 50 / 24 / 1/step]
008 Paper Transfer: Low : 2nd:S2
*ENG
*ENG
*ENG
[1 to 50 / 29 / 1/step]
011 Paper Transfer: Low: 1st: S3
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
113
*ENG
*ENG
[1 to 50 / 27 / 1/step]
150 mm > S5 size (Paper width)
[1 to 50 / 4 / 1/step]
150 mm > S5 size (Paper width)
2421
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2403 and SP2407 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
The paper leading edge area can be adjusted with SP2422.
*ENG
*ENG
*ENG
*ENG
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
Normal: 120 mm/sec, Low: 60 mm/sec
114
*ENG
*ENG
*ENG
*ENG
[0 to 30 / 0 / 2 mm/step]
System SP2xxx
Adjusts the correction coefficient to the paper transfer roller current for the paper trailing
edge in each mode. SP2403 and SP2407 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
The paper trailing edge area can be adjusted with SP2424.
*ENG
*ENG
*ENG
*ENG
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
*ENG
*ENG
*ENG
2430
[-98 to 0 / 0 / 2 mm/step]
*ENG
[1 to 50 / 39 / 1 /step]
*ENG
[1 to 50 / 26 / 1 /step]
*ENG
[1 to 50 / 39 / 1 /step]
*ENG
[1 to 50 / 33 / 1 /step]
009 PaperTransfer:BW:Low:1st
*ENG
*ENG
[1 to 50 / 25 / 1 /step]
115
*ENG
[1 to 50 / 45 / 1 /step]
*ENG
[1 to 50 / 31 / 1 /step]
Adjusts the current for the paper transfer roller for thin paper in black-and-white mode.
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
[0 to 200 / 20 / 1 A /step]
*ENG
[0 to 250 / 12 / 1 A /step]
Adjusts the current for the paper transfer roller for thin paper in full color mode.
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
[0 to 200 / 23 / 1 A /step]
*ENG
[0 to 200 / 13 / 1 A /step]
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2453 and SP2457 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
The paper leading edge area can be adjusted with SP2472.
*ENG
*ENG
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
Normal: 120 mm/sec, Low: 60 mm/sec
116
System SP2xxx
*ENG
*ENG
[0 to 30 / 0 / 2 mm/step]
Adjusts the correction coefficient to the paper transfer roller current for the paper trailing
edge in each mode. SP2453 and SP2457 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
*ENG
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
*ENG
2480
[-100 to 0 / 0 / 2 mm/step]
*ENG
[1 to 50 / 24 / 1 /step]
*ENG
[1 to 50 / 38 / 1 /step]
*ENG
[1 to 50 / 32 / 1 /step]
*ENG
[1 to 50 / 44 / 1 /step]
2482
*ENG
[0 to 200 / 15 / 1 A /step]
001 Adjusts the transfer current of the paper transfer roller for the 1st side of gloss paper in black
and white mode.
117
2483
*ENG
[0 to 200 / 15 / 1 A /step]
001 Adjusts the transfer current of the paper transfer roller for the 1st side of gloss paper in full
color mode.
2485
*ENG
*ENG
[0 to 30 / 0 / 2 mm/step]
*ENG
*ENG
[-100 to 0 / 0 / 2 mm/step]
*ENG
[1 to 50 / 17 / 1 /step]
*ENG
[1 to 50 / 21 / 1 /step]
2486
Adjusts the current for the paper transfer roller for thick 1 paper in black-and-white mode.
Thick: 60 mm/sec
*ENG
[0 to 200 / 15 / 1 A /step]
*ENG
Not used
Adjusts the current for the paper transfer roller for thick 1 paper in full color mode.
Thick: 60 mm/sec
118
System SP2xxx
*ENG
[0 to 200 / 15 / 1 A /step]
*ENG
Not used
[Thick-T:Size Correct:BW]
2511
Adjusts the size correction coefficient for the paper transfer roller current for each paper size.
SP2502 and SP2507 are multiplied by these SP values.
Thick: 60 mm/sec
*ENG
*ENG
*ENG
*ENG
Not used
[100 to 4000 / 150 / 5%/step]
*ENG
*ENG
Not used
[100 to 4000 / 275 / 5%/step]
*ENG
*ENG
Not used
*ENG
*ENG
[Thick-T:Size Correct:FC]
2512
Adjusts the size correction coefficient for the paper transfer roller current for each paper size.
SP2502 and SP2507 are multiplied by these SP values.
Thick: 60 mm/sec
119
*ENG
*ENG
*ENG
*ENG
Not used
[100 to 4000 / 115 / 5%/step]
*ENG
*ENG
Not used
[100 to 4000 / 405 / 5%/step]
*ENG
*ENG
Not used
*ENG
*ENG
[Thick:Size-Env.Correct:BW] DFU
2513
Adjusts the size correction coefficient table for the paper transfer roller current for each paper
size. SP2502 and SP2507 are multiplied by these SP values.
Thick: 60 mm/sec
*ENG
*ENG
[1 to 50 / 30 / 1/step]
S1 size > 290 mm (Paper width)
Not used
[1 to 50 / 36 / 1/step]
120
*ENG
*ENG
Not used
System SP2xxx
[1 to 50 / 40 / 1/step]
009 Paper Transfer: 1st: S3
*ENG
*ENG
Not used
[1 to 50 / 27 / 1/step]
*ENG
*ENG
Not used
*ENG
*ENG
[1 to 50 / 20 / 1/step]
150 mm > S5 size (Paper width)
Not used
[Thick:Size-Env.Correct:FC] DFU
2514
Adjusts the size correction coefficient table for the paper transfer roller current for each paper
size. SP2502 and SP2507 are multiplied by these SP values.
Thick: 60 mm/sec
*ENG
*ENG
[1 to 50 / 30 / 1/step]
S1 size > 290 mm (Paper width)
Not used
[1 to 50 / 49 / 1/step]
*ENG
*ENG
Not used
[1 to 50 / 50 / 1/step]
*ENG
*ENG
Not used
[1 to 50 / 35 / 1/step]
*ENG
121
*ENG
*ENG
*ENG
Not used
[1 to 50 / 6 / 1/step]
150 mm > S5 size (Paper width)
Not used
3
2521
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2502 and SP2507 are multiplied by these SP values.
Thick: 60 mm/sec
The paper leading edge area can be adjusted with SP2522.
*ENG
*ENG
Not used
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
Thick: 60 mm/sec
*ENG
[0 to 30 / 0 / 2 mm/step]
*ENG
Not used
Adjusts the correction coefficient to the paper transfer roller current for the paper trailing
edge in each mode. SP2502 and SP2507 are multiplied by these SP values.
Thick: 60 mm/sec
The paper trailing edge area can be adjusted with SP2524.
122
*ENG
System SP2xxx
*ENG
Not used
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
Thick: 60 mm/sec
*ENG
[0 to -100 / 0 / 2 mm/step]
*ENG
Not used
*ENG
[1 to 50 / 17 / 1 /step]
*ENG
Not used
*ENG
[1 to 50 / 29 / 1 /step]
*ENG
Not used
2530
Adjusts the current for the paper transfer roller for thick2 paper in black-and-white mode.
Thick: 60 mm/sec
*ENG
[0 to 200 / 10 / 1 A /step]
*ENG
Not used
Adjusts the current for the paper transfer roller for thick2 paper in full color mode.
Thick: 60 mm/sec
*ENG
[0 to 200 / 13 / 1 A /step]
*ENG
Not used
123
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2553 and SP2558 are multiplied by these SP values.
Thick: 60 mm/sec
*ENG
*ENG
Not used
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
Thick: 60 mm/sec
*ENG
[0 to 30 / 0 / 2mm/step]
*ENG
Not used
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2553 and SP2558 are multiplied by these SP values.
Thick: 60 mm/sec
The paper trailing edge area can be adjusted with SP2574.
*ENG
*ENG
Not used
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
Thick: 60 mm/sec
124
System SP2xxx
*ENG
[0 to -100 / 0 / 2 mm/step]
*ENG
Not used
*ENG
[0 to 50 / 36 / 1 /step]
*ENG
Not used
*ENG
[0 to 50 / 23 / 1 /step]
*ENG
Not used
2580
2603
2608
*ENG
*ENG
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2603 and SP2608 are multiplied by these SP values.
The paper leading edge area can be adjusted with SP2622.
*ENG
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
*ENG
[0 to 30 / 0 / 2 mm/step]
125
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2603 and SP2608 are multiplied by these SP values.
The paper trailing edge area can be adjusted with SP2624.
*ENG
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
*ENG
[98 to 0 / 0 / 2 mm/step]
*ENG
*ENG
Adjusts the current for the paper transfer roller for thick paper 3 in black-and-white mode.
Thick: 60 mm/sec
*ENG
[0 to 200 / 10 / 1 A /step]
*ENG
Not used
Adjusts the current for the paper transfer roller for thick paper 3 in full color mode.
Thick: 60 mm/sec
126
*ENG
[0 to 200 / 13 / 1 A /step]
*ENG
Not used
System SP2xxx
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2651 and SP2652 are multiplied by these SP values.
Thick: 60 mm/sec
The paper leading edge area can be adjusted with SP2655.
*ENG
*ENG
Not used
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
Thick: 60 mm/sec
*ENG
[0 to 30 / 0 / 2 mm/step]
*ENG
Not used
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2651 and SP2652 are multiplied by these SP values.
Thick: 60 mm/sec
The paper trailing edge area can be adjusted with SP2657.
*ENG
*ENG
Not used
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
Thick: 60 mm/sec
127
*ENG
[-98 to 0 / 0 / 2 mm/step]
*ENG
Not used
*ENG
[1 to 50 / 36 / 1 /step]
*ENG
Not used
*ENG
[1 to 50 / 23 / 1 /step]
*ENG
Not used
*ENG
*ENG
*ENG
[0 to 200 / 11 / 1 - A /step]
*ENG
[0 to 200 / 13 / 1 - A /step]
[0 to 200 / 20 / 1 - A /step]
128
*ENG
[0 to 200 / 25 / 1 - A /step]
*ENG
[0 to 200 / 28 / 1 - A /step]
*ENG
*ENG
[0 to 200 / 14 / 1 - A /step]
System SP2xxx
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2703 and SP2707 are multiplied by these SP values.
The paper leading edge area can be adjusted with SP2722.
*ENG
*ENG
*ENG
*ENG
3
[0 to 400 / 100 / 5 %/step]
[M-Thick:SwTiming:L-Edge] DFU
2722
*ENG
*ENG
*ENG
*ENG
[0 to 30 / 0 / 2 mm /step]
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2703 and SP2707 are multiplied by these SP values.
The paper trailing edge area can be adjusted with SP2724.
129
*ENG
*ENG
*ENG
*ENG
[M-Thick:SwTiming:T-Edge] DFU
2724
*ENG
*ENG
*ENG
*ENG
2730
[0 to -100 / 0 / 2 mm/step]
*ENG
[1 to 50 / 23 / 1 /step]
*ENG
[1 to 50 / 26 / 1 /step]
*ENG
[1 to 50 / 38 / 1 /step]
*ENG
[1 to 50 / 33 / 1 /step]
*ENG
[1 to 50 / 32 / 1 /step]
*ENG
[1 to 50 / 21 / 1 /step]
*ENG
[1 to 50 / 48 / 1 /step]
*ENG
[1 to 50 / 28 / 1 /step]
Adjusts the current for the paper transfer roller for special paper 1 in black-and-white mode.
Normal: 120mm/sec, Low: 60mm/sec
130
System SP2xxx
*ENG
*ENG
*ENG
[0 to 200 / 11 / 1 A /step]
*ENG
[0 to 200 / 13 / 1 A /step]
[0 to 200 / 20 / 1 A /step]
Adjusts the current for the paper transfer roller for special paper 1 in full color mode.
*ENG
[0 to 200 / 25 / 1 A /step]
*ENG
[0 to 200 / 28 / 1 A /step]
*ENG
[0 to 200 / 11 / 1 A /step]
*ENG
[0 to 200 / 14 / 1 A /step]
[SP1,2,3-T:Size Correct:BW]
2761
Adjusts the size correction coefficient for the paper transfer roller current for each paper size.
SP2753 and SP2757 are multiplied by these SP values.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
*ENG
*ENG
*ENG
[100 to 4000 / 140 / 5%/step]
*ENG
*ENG
131
*ENG
*ENG
*ENG
*ENG
011 PaperTransfer:Low:1st:S3
*ENG
012 PaperTransfer:Low:2nd:S3
*ENG
*ENG
*ENG
015 PaperTransfer:Low:1st:S4
*ENG
016 PaperTransfer:Low:2nd:S4
*ENG
*ENG
132
System SP2xxx
*ENG
019 PaperTransfer:Low:1st:S5
*ENG
020 PaperTransfer:Low:2nd:S5
*ENG
[SP1,2,3-T:Size Correct:FC]
2762
Adjusts the size correction coefficient for the paper transfer roller current for each paper size.
SP2753 and SP2757 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
*ENG
*ENG
*ENG
[100 to 4000 / 130 / 5%/step]
*ENG
*ENG
*ENG
*ENG
*ENG
133
*ENG
011 PaperTransfer:Low:1st:S3
*ENG
012 PaperTransfer:Low:2nd:S3
*ENG
*ENG
*ENG
015 PaperTransfer:Low:1st:S4
*ENG
134
016 PaperTransfer:Low:2nd:S4
*ENG
*ENG
*ENG
019 PaperTransfer:Low:1st:S5
*ENG
020 PaperTransfer:Low:2nd:S5
*ENG
System SP2xxx
Adjusts the size correction coefficient table for the paper transfer roller current for each paper
size. SP2753 and SP2757 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
*ENG
*ENG
[1 to 50 / 30 / 1/step]
*ENG
*ENG
[1 to 50 / 23 / 1/step]
005 Paper Transfer: Normal: 1st: S2
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
011 PaperTransfer:Low:1st:S3
*ENG
135
[1 to 50 / 13 / 1/step]
012 PaperTransfer:Low:2nd:S3
*ENG
*ENG
*ENG
015 PaperTransfer:Low:1st:S4
*ENG
016 PaperTransfer:Low:2nd:S4
*ENG
*ENG
*ENG
019 PaperTransfer:Low:1st:S5
*ENG
020 PaperTransfer:Low:2nd:S5
*ENG
Adjusts the size correction coefficient table for the paper transfer roller current for each paper
size. SP2753 and SP2757 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
136
System SP2xxx
*ENG
*ENG
[1 to 50 / 30 / 1/step]
*ENG
*ENG
[1 to 50 / 37 / 1/step]
*ENG
[1 to 50 / 16 / 1/step]
006 Paper Transfer: Normal: 2nd: S2
*ENG
*ENG
*ENG
*ENG
*ENG
011 PaperTransfer:Low:1st:S3
*ENG
012 PaperTransfer:Low:2nd:S3
*ENG
*ENG
137
[1 to 50 / 7 / 1/step]
014 Paper Transfer: Normal: 2nd: S4
*ENG
015 PaperTransfer:Low:1st:S4
*ENG
016 PaperTransfer:Low:2nd:S4
*ENG
*ENG
*ENG
019 PaperTransfer:Low:1st:S5
*ENG
020 PaperTransfer:Low:2nd:S5
*ENG
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2753 and SP2757 are multiplied by these SP values.
Normal: 120mm/sec, Low: 60mm/sec
The paper leading edge area can be adjusted with SP2772.
138
*ENG
*ENG
*ENG
*ENG
System SP2xxx
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
*ENG
*ENG
*ENG
[0 to 30 / 0 / 2 mm/step]
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2753 and SP2757 are multiplied by these SP values.
Normal: 120 mm/sec, Low: 60 mm/sec
The paper trailing edge area can be adjusted with SP2774.
*ENG
*ENG
*ENG
*ENG
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
*ENG
*ENG
*ENG
[-98 to 0 / 0 / 2 mm/step]
139
2780
*ENG
[1 to 50 / 23 / 1 /step]
*ENG
[1 to 50 / 26 / 1 /step]
*ENG
[1 to 50 / 38 / 1 /step]
*ENG
[1 to 50 / 33 / 1 /step]
*ENG
[1 to 50 / 32 / 1 /step]
*ENG
[1 to 50 / 21 / 1 /step]
*ENG
[1 to 50 / 48 / 1 /step]
*ENG
[1 to 50 / 28 / 1 /step]
2783
2787
*ENG
[0 to 200 / 15 / 1 A /step]
*ENG
[0 to 200 / 15 / 1 A /step]
[SP4,5,6-T:Size Correct:BW]
2791
Adjusts the size correction coefficient for the paper transfer roller current for each paper size.
SP2783 and SP2787 are multiplied by these SP values.
*ENG
*ENG
140
System SP2xxx
*ENG
*ENG
*ENG
[SP4,5,6-T:Size Correct:FC]
2792
Adjusts the size correction coefficient for the paper transfer roller current for each paper size.
SP2783 and SP2787 are multiplied by these SP values.
*ENG
*ENG
*ENG
*ENG
*ENG
Adjusts the size correction coefficient table for the paper transfer roller current for each paper
size. SP2783 and SP2787 are multiplied by these SP values.
*ENG
[1 to 50 / 30 / 1/step]
S1 size > 290 mm (Paper width)
141
[1 to 50 / 36 / 1/step]
005 Paper Transfer: S2
*ENG
*ENG
*ENG
*ENG
Adjusts the size correction coefficient table for the paper transfer roller current for each paper
size. SP2783 and SP2787 are multiplied by these SP values.
*ENG
[1 to 50 / 30 / 1/step]
S1 size > 290 mm (Paper width)
[1 to 50 / 49 / 1/step]
*ENG
*ENG
142
*ENG
*ENG
System SP2xxx
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2783 and SP2787 are multiplied by these SP values.
The paper leading edge area can be adjusted with SP2796.
*ENG
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
*ENG
[0 to 30 / 0 / 2 mm/step]
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2783 and SP2787 are multiplied by these SP values.
The paper trailing edge area can be adjusted with SP2798.
*ENG
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
*ENG
[-98 to 0 / 0 / 2 mm/step]
*ENG
[1 to 50 / 17 / 1 /step]
*ENG
[1 to 50 / 29 / 1 /step]
2799
143
Adjusts the current for the paper transfer roller for special paper 2 in black-and-white mode.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
*ENG
*ENG
[0 to 200 / 11 / 1 A /step]
*ENG
[0 to 200 / 13 / 1 A /step]
[0 to 200 / 20 / 1 A /step]
Adjusts the current for the paper transfer roller for special paper 2 in full color mode.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
[0 to 200 / 25 / 1 A /step]
*ENG
[0 to 200 / 28 / 1 A /step]
*ENG
[0 to 200 / 11 / 1 A /step]
*ENG
[0 to 200 / 14 / 1 A /step]
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2803 and SP2807 are multiplied by these SP values.
Normal: 120mm/sec, Low: 60mm/sec
The paper leading edge area can be adjusted with SP2822.
144
*ENG
*ENG
*ENG
*ENG
System SP2xxx
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
*ENG
*ENG
*ENG
[0 to 30 / 0 / 2 mm/step]
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2803 and SP2807 are multiplied by these SP values.
Normal: 120mm/sec, Low: 60mm/sec
The paper trailing edge area can be adjusted with SP2824.
*ENG
*ENG
*ENG
*ENG
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
*ENG
*ENG
*ENG
[-98 to 0 / 0 / 2 mm/step]
145
2830
*ENG
[1 to 50 / 23 / 1 /step]
*ENG
[1 to 50 / 26 / 1 /step]
*ENG
[1 to 50 / 38 / 1 /step]
*ENG
[1 to 50 / 33 / 1 /step]
*ENG
[1 to 50 / 32 / 1 /step]
*ENG
[1 to 50 / 21 / 1 /step]
*ENG
[1 to 50 / 48 / 1 /step]
*ENG
[1 to 50 / 28 / 1 /step]
2833
2837
*ENG
[0 to 200 / 15 / 1 A /step]
*ENG
[0 to 200 / 15 / 1 A /step]
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2833 and SP2837 are multiplied by these SP values.
The paper leading edge area can be adjusted with SP2846.
146
*ENG
System SP2xxx
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
*ENG
[0 to 30 / 0 / 2 mm/step]
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2833 and SP2837 are multiplied by these SP values.
*ENG
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
*ENG
[-98 to 0 / 0 / 2 mm/step]
*ENG
[1 to 50 / 17 / 1 /step]
*ENG
[1 to 50 / 29 / 1 /step]
2849
Adjusts the current for the paper transfer roller for special paper 3 in black-and-white mode.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
*ENG
*ENG
[0 to 200 / 11 / 1 A /step]
*ENG
[0 to 200 / 13 / 1 A /step]
[0 to 200 / 20 / 1 A /step]
147
Adjusts the current for the paper transfer roller for special paper 3 in full color mode.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
[0 to 200 / 25 / 1 A /step]
*ENG
[0 to 200 / 28 / 1 A /step]
*ENG
[0 to 200 / 11 / 1 A /step]
*ENG
[0 to 200 / 14 / 1 A /step]
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2852 and SP2857 are multiplied by these SP values.
Normal: 120mm/sec, Low: 60mm/sec
The paper leading edge area can be adjusted with SP2872.
*ENG
*ENG
*ENG
*ENG
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
Normal: 120mm/sec, Low: 60mm/sec
148
*ENG
*ENG
*ENG
*ENG
[0 to 30 / 0 / 2 mm/step]
System SP2xxx
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2852 and SP2857 are multiplied by these SP values.
Normal: 120mm/sec, Low: 60mm/sec
The paper trailing edge area can be adjusted with SP2874.
*ENG
*ENG
*ENG
*ENG
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
Normal: 120mm/sec, Low: 60mm/sec
*ENG
*ENG
*ENG
*ENG
2880
[-98 to 0 / 0 / 2 mm/step]
*ENG
[1 to 50 / 23 / 1 /step]
*ENG
[1 to 50 / 26 / 1 /step]
*ENG
[1 to 50 / 38 / 1 /step]
*ENG
[1 to 50 / 33 / 1 /step]
*ENG
[1 to 50 / 32 / 1 /step]
*ENG
[1 to 50 / 21 / 1 /step]
149
*ENG
[1 to 50 / 48 / 1 /step]
*ENG
[1 to 50 / 28 / 1 /step]
2883
3
2887
*ENG
[0 to 200 / 15 / 1 A /step]
*ENG
[0 to 200 / 15 / 1 A /step]
Adjusts the correction to the paper transfer roller current at the paper leading edge in each
mode. SP2883 and SP2887 are multiplied by these SP values.
The paper leading edge area can be adjusted with SP2896.
*ENG
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the
paper leading edge between the erase margin area and the image area.
*ENG
[0 to 30 / 0 / 2 mm/step]
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each
mode. SP2883 and SP2887 are multiplied by these SP values.
The paper trailing edge area can be adjusted with SP2898.
150
System SP2xxx
*ENG
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the
paper trailing edge between the erase margin area and the image area.
*ENG
[-98 to 0 / 0 / 2 mm/step]
*ENG
[1 to 50 / 17 / 1 /step]
*ENG
[1 to 50 / 29 / 1 /step]
2900
*ENG
[0 to 60 / 5 / 1sec /step]
*ENG
[Fus.Reload:DrumIdleTimeOffset] DFU
2901
Adjusts the drum idling time for each coverage at the re-load temperature in the half speed
mode.
001 Coverage:0-6%
*ENG
002 Coverage:6-10%
*ENG
003 Coverage:10-20%
*ENG
004 Coverage:20-40%
*ENG
005 Coverage:40%over
*ENG
2902
001 All: BW
*ENG
[0 to 200 / 60 / 10 msec/step]
002 All: FC
*ENG
[0 to 200 / 50 / 10 msec/step]
151
003 DevRev: FC
*ENG
[0 to 200 / 70 / 10 msec/step]
004 DevRev: Bk
*ENG
005 All
*ENG
[0 to 400000 / 0 / 10/step]
006 K
*ENG
007 C
*ENG
008 M
*ENG
009 Y
*ENG
[0 to 999999999 / - / 1/step]
001
Adjusts the time when the image transfer belt motor and drum motors reverses from normal
rotation after job end.
Bk OPC Drum & Intermediate
Transfer
*ENG
*ENG
003 FC Development
*ENG
2904
[ImageTrunsferRevTime] DFU
Adjusts the time for how long the image transfer belt motor reverses after job end.
003 All
2906
*ENG
001 Color
*ENG
002 Bk
*ENG
2908
[0 to 200 / 50 / 10 msec/step]
[0 to 359 / 0 / 1 deg/step]
[GainAdj:TransferM] DFU
Gain Adjustment of Image Transfer Belt Motor
[0 or 1 / 0 / 1/step]
*ENG
152
System SP2xxx
[0 or 1 / 1 / 1/step]
002 60 mm/sec
*ENG
2915
[GainAdj:BkOpcDevM] DFU
[0 or 1 / 0 / 1/step]
*ENG
[0 or 1 / 1 / 1/step]
002 60 mm/sec
*ENG
2916
[GainAdj:ColorOpcM] DFU
[0 or 1 / 0 / 1/step]
*ENG
002 60 mm/sec
*ENG
2920
001 TransferMotorCtrl
*ENG
[0 or 1 / 1 / 1 /step]
0: FG Control
1: ENC Control
002
SC443 Count
*ENG
[0 to 10 / 0 / 1 /step]
153
001 Bias
2931
001
003
2940
*ENG
*ENG
Specifies the timing for the transfer roller cleaning after job end in the normal speed mode.
T15:Low Speed
*ENG
Specifies the timing for the transfer roller cleaning after job end in the low speed mode.
[Charge Bias On Timing]
*ENG
*ENG
If a horizontal white band at 40 mm from the leading edge occurs in the low speed mode,
002 change this setting from "-80" to "-500".
[Side Effect]:
"580 msec" is added to the first copy/ print time when using the low speed mode.
2941
001 T5:Bk:Normal
*ENG
002 T7:FC:Normal
*ENG
003 T5:Bk:Low
*ENG
*ENG
*ENG
[0 to 10 / 0 / 1 sec/step]
2960
154
System SP2xxx
2971
001
003
2972
*ENG
[360 to 80 / 0 / 10 msec/step]
Adjusts the timing for the non-image area bias of the image transfer roller in the normal speed.
T1 BW:Bias On:Low
*ENG
Adjusts the timing for the non-image area bias of the image transfer roller in the low speed.
*ENG
*ENG
*ENG
[0 to 5000 / 0 / 1 page/step]
2973
001 Specifies the threshold pages for the forced processing stop at a continuous printing job.
0: No forced processing stop (default)
2974
*ENG
[0 to 3000 / 0 / 10 msec/step]
*ENG
[0 to 3000 / 0 / 10 msec/step]
2990
001
*ENG
[0 or 1 / 0 / 1 /step]
0: No limit, 1: Limit
Limit or does not limit the duty control for a continuous printing job.
002
*ENG
Specifies the judgment time for the duty control for a continuous printing job.
Duty Control Thresh
*ENG
[0 to 999999999 / 0 / 1 mm/step]
003 Specifies the threshold for the duty control for a continuous printing job.
0: No duty control (default)
155
*ENG
[0 to 5000 / 0 / 1 page/step]
Specifies the threshold page for the forced processing stop without the duty limit.
Drum Stop Time: No Duty
005 Control
*ENG
*ENG
*ENG
[0 to 5000 / 1 / 1 page/step]
Specifies the threshold page for the forced processing stop with the duty limit.
008
009
010
*ENG
*ENG
*ENG
*ENG
*ENG
156
*ENG
[0 to 300 / 30 / 1 min/step]
System SP3xxx
System SP3xxx
SP3-XXX (Process)
3011
All colors are displayed. The results are displayed in the order "Y C M K"
e.g., 11 (Y) 99 (C) 11 (M) 11 (K): The self-check for Cyan failed but the others were
successful.
See the "Error Condition Tables" in the Process Control Error section for details.
157
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3013
003 Execution: Bk
004 Execution: C
005 Execution: M
006 Execution: Y
3014
*ENG
1: Success
2 to 9: Failure
001 Displays the developer initialization result. See the "Error Condition Tables" in the Process
Control Error section for details on the meaning of each code.
All colors are displayed. Values are displayed in the order Y M C Bk.
e.g., 1 (Y) 1 (M) 2 (C) 1 (Bk): Initialization of Cyan failed but the others succeeded.
158
System SP3xxx
3015
003 Execution: Bk
004 Execution: C
005 Execution: M
006 Execution: Y
3016
*ENG
*ENG
*ENG
001005
3020
[0 to 30 / 4 / 1 sec/step]
*ENG
[0 to 5 / 5 / 0.01 V/step]
*ENG
*ENG
[0 to 99 / 20 / 1 time/step]
*ENG
*ENG
[0 to 99 / 10 / 1 times/step]
159
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 99 / 0 / 1 times/step]
*ENG
*ENG
*ENG
3021
*ENG
*ENG
*ENG
*ENG
005008
[0 to 200 / 30 / 1 sec/step]
Sets the execution flag of the developer initialization for each color.
*ENG
*ENG
*ENG
*ENG
*ENG
[0 or 1 / 0 / 1/step]
3022
160
System SP3xxx
*ENG
*ENG
*ENG
*ENG
3041
[0 or 1 / 0 / 1/step]
001
Bias Control
*ENG
LD Power Control
*ENG
[0 or 1 / 0 / 1/step] Alphanumeric
*ENG
0: Permit
1: Forbid
*ENG
0: Not Execute
1: Process Control
2: TC Control
*ENG
0: FIXED
1: INITIALIZED
2: CALCULATED
161
3043
*ENG
[0 to 9 / 4 / 1 time/step]
Specifies the maximum number of repeats of the toner density adjustment at power on.
0: Disabled, 1 to 3: Repeat number,
001 4: Repeat three times (No consumption mode)
5: Repeat three times (Toner is supplied only when the toner density is too low, and toner is
consumed only when the toner density is too dark.)
6 to 9: Disabled
Repeat Number: Initial
*ENG
[0 to 9 / 3 / 1 time/step]
Specifies the maximum number of repeats of the toner density adjustment at the developer
initialization.
002
*ENG
[0 to 9 / 0 / 1 time/step]
Specifies the maximum number of repeats of the toner density adjustment in stand by mode.
0: Disabled, 1 to 3: Repeat number,
003 4: Repeat three times (No consumption mode)
5: Repeat three times (Toner is supplied only when the toner density is too low, and toner is
consumed only when the toner density is too dark.)
6 to 9: Disabled
Repeat Number: ACC
*ENG
[0 to 9 / 3 / 1 time/step]
Specifies the maximum number of repeats of the toner density adjustment at ACC.
0: Disabled, 1 to 3: Repeat number,
004 4: Repeat three times (No consumption mode)
5: Repeat three times (Toner is supplied only when the toner density is too low, and toner is
consumed only when the toner density is too dark.)
6 to 9: Disabled
162
System SP3xxx
005
*ENG
[0 to 9 / 3 / 1 time/step]
*ENG
[0 to 9 / 4 / 1 time/step]
Not used
Repeat Number: Job End
Specifies the maximum number of repeats of the toner density adjustment at job end.
0: Disabled, 1 to 3: Repeat number,
006 4: Repeat three times (No consumption mode)
5: Repeat three times (Toner is supplied only when the toner density is too low, and toner is
consumed only when the toner density is too dark.)
6 to 9: Disabled
Repeat Number:Interrupt
*ENG
[0 to 9 / 0 / 1 time/step]
007 Specifies the maximum number of repeats of the toner density adjustment during printing.
DFU
008
*ENG
Adjusts the time for the toner supply mode when a toner density is detected to be low.
C-pattern: Bk
*ENG
[0 to 255 / 5 / 1 time/step]
009 Specifies the belt mark generating time for checking the black toner density when toner
density is detected to be low at the toner density adjustment.
C-pattern: C
*ENG
[0 to 255 / 5 / 1 time/step]
010 Specifies the belt mark generating time for checking the magenta toner density when toner
density is detected to be low at the toner density adjustment.
C-pattern: M
*ENG
[0 to 255 / 5 / 1 time/step]
011 Specifies the belt mark generating time for checking the cyan toner density when toner density
is detected to be low at the toner density adjustment.
C-pattern: Y
*ENG
[0 to 255 / 5 / 1 time/step]
012 Specifies the belt mark generating time for checking the yellow toner density when toner
density is detected to be low at the toner density adjustment.
013
T1 Bias: Bk
*ENG
[0 to 80 / 10 / 1 A/step]
163
014
015
016
3
017
T1 Bias: C
T1 Bias: M
T1 Bias: Y
164
*ENG
[0 to 80 / 10 / 1 A/step]
*ENG
[0 to 250 / 10 / 1 sec/step]
[0 to 15 / 15 / 1 /step]
Adjusts the LD duty for the toner consumption mode at the toner density adjustment.
In toner consumption mode, toner is discharged when the detected development gamma
values (SP3611-001) exceed the target values (SP3611-005) by more than the specified
thresholds (SP3239-009).
*ENG
[0 to 15 / 15 / 1 /step]
Adjusts the LD duty for the toner consumption mode at the toner density adjustment.
In toner consumption mode, toner is discharged when the detected development gamma
values (SP3611-002) exceed the target values (SP3611-006) by more than the specified
thresholds (SP3239-009).
*ENG
[0 to 15 / 15 / 1 /step]
Adjusts the LD duty for the toner consumption mode at the toner density adjustment.
In toner consumption mode, toner is discharged when the detected development gamma
values (SP3611-003) exceed the target values (SP3611-007) by more than the specified
thresholds (SP3239-009).
C-Pattern: LD: DUTY: Y
021
[0 to 80 / 10 / 1 A/step]
*ENG
[0 to 80 / 10 / 1 A/step]
*ENG
*ENG
[0 to 15 / 15 / 1 /step]
Adjusts the LD duty for the toner consumption mode at the toner density adjustment.
In toner consumption mode, toner is discharged when the detected development gamma
values (SP3611-004) exceed the target values (SP3611-008) by more than the specified
thresholds (SP3239-009).
System SP3xxx
3044
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 Y
*ENG
3045
[0 to 4 / 4 / 1/step] Alphanumeric
0: FIXED (with the supply rates stored with SP 3401)
1: PID (Vtref_Fixed)
2: PID (Vtref_Control)
3: MBD (Vtref_Fixed)
4: MBD (Vtref_Control)
001 ON/OFF
*ENG
[0 or 1 / 0 / 1/step]
0: Detect, 1: Not Detect
[0 or 1 / 0 / 1/step]
002 NE Detection
*ENG
3101
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
165
009-012
Displays the remaining amount of each color toner. These are calculated by the operating
times of the toner supply pumps.
*ENG
*ENG
*ENG
*ENG
Adjusts the threshold of toner near end for each color. The toner near end message appears
on the LCD when the remaining toner amount reaches this threshold. When one of these
013-016
SPs (SP3-101-009 to 012 or -032 to -035) reaches this threshold, toner near end is
detected.
013 Near End Thresh: Bk
*ENG
*ENG
*ENG
*ENG
Delta Vt Threshold
*ENG
[0 to 600 / 13 / 1 g/step]
[0 to 600 / 3 / 1 g/step]
021 This SP is the threshold for toner end. Delta Vt: Vt-Vtref
When both this SP and SP3-101-026 occur at same time, toner end is determined.
022-025
Displays the total delta Vt (Vt-Vtref) value for each color.These are calculated by pixel
counting.
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 255 / 10 / 1 V/step]
028-031 Displays the consumed toner amount calculated with the pixel count for each color.
166
System SP3xxx
*ENG
*ENG
*ENG
*ENG
032-035 Displays the remaining toner amount for each color, using pixel count.
032 Pixel: Remaining : Bk
*ENG
*ENG
*ENG
*ENG
3
[-50000 to 600 / 0 / 0.001 g/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 0 x FFFFFFFF / 0 / 1 sec/step]
050-053 Adjusts the threshold of the remaining toner for the toner near-end detection. DFU
167
*ENG
*ENG
*ENG
*ENG
[1 to 600 / 57 / 1 g/step]
3102
001 Repeat: Bk
*ENG
002 Repeat: C
*ENG
003 Repeat: M
*ENG
004 Repeat: Y
*ENG
3131
[1 to 20 / 5 / 1 time/step]
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 Y
*ENG
3201
168
Adjusts the number of times toner supply is attempted for each color when the TD sensor
continues to detect toner end during toner recovery.
[0 to 99 / 0 / 1 time/step]
001 Current: Bk
*ENG
002 Current: C
*ENG
003 Current: M
*ENG
004 Current: Y
*ENG
System SP3xxx
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3221
002 Current: C
*ENG
003 Current: M
*ENG
004 Current: Y
*ENG
008
[Vtcnt: Display/Set]
001 Current: Bk
005-
[2 to 5 / 4 / 0.01 V/step]
Displays or adjusts the Vtcnt value for each color at developer initialization.
169
005 Initial: Bk
*ENG
006 Initial: C
*ENG
007 Initial: M
*ENG
008 Initial: Y
*ENG
3222
002 Current: C
*ENG
003 Current: M
*ENG
004 Current: Y
*ENG
008
*ENG
006 Initial: C
*ENG
007 Initial: M
*ENG
008 Initial: Y
*ENG
012
*ENG
*ENG
*ENG
*ENG
3223
Displays or adjusts the Vtref value for each color at developer initialization.
005 Initial: Bk
009-
170
[Vtcnt: Display/Set]
001 Current: Bk
005-
[2 to 5 / 4 / 0.01 V/step]
System SP3xxx
001 Lower: Bk
*ENG
002 Lower: C
*ENG
003 Lower: M
*ENG
004 Lower: Y
*ENG
005 Upper: Bk
*ENG
006 Upper: C
*ENG
007 Upper: M
*ENG
008 Upper: Y
*ENG
009 Initial TC
*ENG
010 Upper: TC
*ENG
011 Lower: TC
*ENG
*ENG
*ENG
*ENG
*ENG
016 UpperTC:K
*ENG
017 UpperTC:C
*ENG
018 UpperTC:M
*ENG
019 UpperTC:Y
*ENG
3224
[0 to 5 / 2 / 0.01 V/step]
[0 to 5 / 4 / 0.01 V/step]
171
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
172
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 255 / 50 / 1 time/step]
*ENG
*ENG
[0 to 100 / 20 / 1 %/step]
*ENG
*ENG
*ENG
[0 to 255 / 6 / 1 time/step]
*ENG
[0 to 100 / 10 / 1 %/step]
[0 to 255 / 14 / 1 time/step]
System SP3xxx
*ENG
[0 to 255 / 4 / 1 time/step]
001 ADD:TIME
*ENG
002 ADD:K
*ENG
003 ADD:C
*ENG
004 ADD:M
*ENG
005 ADD:Y
*ENG
007 ADD:LowSpd
*ENG
008 MSEC_V
*ENG
[0 to 1 / 0.080 / 0.001/step]
009 N_Delay
*ENG
[0 to 200 / 27 / 1 /step]
030 PID:I:K
*ENG
031 PID:I:C
*ENG
032 PID:I:M
*ENG
033 PID:I:Y
*ENG
034 PID:P:K
*ENG
035 PID:P:C
*ENG
036 PID:P:M
*ENG
037 PID:P:Y
*ENG
039 PID:I:LowSpd
*ENG
041 PID:P:LowSpd
*ENG
060 AWILOW:K
*ENG
061 AWILOW:C
*ENG
062 AWILOW:M
*ENG
063 AWILOW:Y
*ENG
173
174
064 AWPUP:K
*ENG
065 AWPUP:C
*ENG
066 AWPUP:M
*ENG
067 AWPUP:Y
*ENG
070 AWILOW:LowSpd
*ENG
071 AWPUP:LowSpd
*ENG
090 SMITH:K
*ENG
091 SMITH:C
*ENG
092 SMITH:M
*ENG
093 SMITH:Y
*ENG
095 SMITH:LowSpd
*ENG
100 Int_conserve_I_K
*ENG
101 Int_conserve_I_C
*ENG
102 Int_conserve_I_M
*ENG
103 Int_conserve_I_Y
*ENG
110 ANC_ref_conserve_K
*ENG
111 ANC_ref_conserve_C
*ENG
112 ANC_ref_conserve_M
*ENG
113 ANC_ref_conserve_Y
*ENG
120 ANC_A3_K
*ENG
121 ANC_A3_C
*ENG
122 ANC_A3_M
*ENG
123 ANC_A3_Y
*ENG
System SP3xxx
124 ANC_A4_K
*ENG
125 ANC_A4_C
*ENG
126 ANC_A4_M
*ENG
127 ANC_A4_Y
*ENG
130 ANC_A3_LowSpd
*ENG
131 ANCA4T_LowSpd
*ENG
150 AWPNI_K
*ENG
151 AWPNI_C
*ENG
152 AWPNI_M
*ENG
153 AWPNI_Y
*ENG
154 PID
*ENG
180 ANCLA_K
*ENG
181 ANCLA_C
*ENG
182 ANCLA_M
*ENG
183 ANCLA_Y
*ENG
184 ANCLB_K
*ENG
185 ANCLB_C
*ENG
186 ANCLB_M
*ENG
187 ANCLB_Y
*ENG
190 ANCLA_LowSpd
*ENG
191 ANCLB_LowSpd
*ENG
210 PIX_TBL_1
*ENG
211 PIX_TBL_2
*ENG
212 PIX_TBL_3
*ENG
213 PIX_TBL_4
*ENG
214 PIX_TBL_5
*ENG
[0 to 5 / 1 / 0.01 /step]
[0 to 5 / 1 / 0.01 /step]
175
215 PIX_TBL_6
*ENG
216 PIX_TBL_7
*ENG
217 PIX_TBL_8
*ENG
218 PIX_TBL_9
*ENG
219 PIX_TBL_10
*ENG
220 PIX_TBL_11
*ENG
221 PIX_TBL_12
*ENG
222 PIX_COR_K
*ENG
223 PIX_COR_C
*ENG
224 PIX_COR_M
*ENG
225 PIX_COR_Y
*ENG
226 SEL_PIX_AVE
*ENG
[1 to 5 / 2 / 1 /step]
231 PID_I_LIM1_Std
*ENG
233 PID_I_LIM1_LowSpd
*ENG
234 PID_I_LIM2_Std
*ENG
236 PID_I_LIM2_LowSpd
*ENG
237 PID_P_LIM1_Std
*ENG
239 PID_P_LIM1_LowSpd
*ENG
240 PID_P_LIM2_Std
*ENG
242 PID_P_LIM2_LowSpd
*ENG
243 PID_I_STDtoLOW
*ENG
244 PID_I_LOWtoSTD
*ENG
[0 to 5 / 2 / 0.01 /step]
3231
176
[0 to 5 / 1 / 0.01 /step]
[0 to 5 / 1 / 0.01 /step]
System SP3xxx
*ENG
*ENG
*ENG
*ENG
3232
001 Vt Proportion: Bk
*ENG
002 Vt Proportion: C
*ENG
003 Vt Proportion: M
*ENG
004 Vt Proportion: Y
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3233
3
[0 to 2550 / 50 / 1 /step]
[1 to 255 / 20 / 1 time/step]
*ENG
*ENG
*ENG
*ENG
*ENG
3234
*ENG
*ENG
3235
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3236
178
001 Latest: Bk
*ENG
002 Latest: C
*ENG
003 Latest: M
*ENG
004 Latest: Y
*ENG
System SP3xxx
3237
3238
*ENG
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 Y
*ENG
3239
[0 to 200 / 5 / 1 sec/step]
3
[0 to 5 / 2.7 / 0.01 V/step]
*ENG
002 (+)Consumption: C
*ENG
003 (+)Consumption: M
*ENG
004 (+)Consumption: Y
*ENG
005 (-)Consumption: Bk
*ENG
006 (-)Consumption: C
*ENG
007 (-)Consumption: M
*ENG
008 (-)Consumption: Y
*ENG
*ENG
*ENG
*ENG
*ENG
013-014 Threshold for image density rank on the image transfer belt.
179
3241
*ENG
*ENG
001 Coefficient: Bk
*ENG
002 Coefficient: C
*ENG
003 Coefficient: M
*ENG
004 Coefficient: Y
*ENG
005 Offset: Bk
*ENG
006 Offset: C
*ENG
007 Offset: M
*ENG
008 Offset: Y
*ENG
3242
180
001 Coefficient: Bk
*ENG
002 Coefficient: C
*ENG
003 Coefficient: M
*ENG
004 Coefficient: Y
*ENG
005 Offset: Bk
*ENG
006 Offset: C
*ENG
007 Offset: M
*ENG
008 Offset: Y
*ENG
System SP3xxx
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3243
[DevBias_SpdCorrectSetting]
Adjusts the coefficient or offset value for development bias correction for each speed.
009 LowSpd:Coef:Bk
*ENG
010 LowSpd:Coef:M
*ENG
011 LowSpd:Coef:C
*ENG
012 LowSpd:Coef:Y
*ENG
013 LowSpd:offset:Bk
*ENG
014 LowSpd:offset:M
*ENG
015 LowSpd:offset:C
*ENG
016 LowSpd:offset:Y
*ENG
3251
[0 to 200 / 0 / 1 V/step]
[Coverage]
These (-001 to -016) are coefficients for SP3-222-009 to -012.
001 Latest: Pixcel Bk
*ENG
*ENG
*ENG
[0 to 9999 / 0 / 1 cm2/step]
*ENG
181
Displays the average coverage of each color for the Vtref correction.
005-008 "Average S" is defined when the number of developed pages does not reach the number
specified with SP3251-017.
005 Average S: Bk
*ENG
006 Average S: C
*ENG
007 Average S: M
*ENG
008 Average S: Y
*ENG
Displays the average coverage of each color for the Vtref correction.
009-012 "Average M" is defined when the number of developed pages does not reach the number
specified with SP3251-018.
009 Average M: Bk
*ENG
010 Average M: C
*ENG
011 Average M: M
*ENG
012 Average M: Y
*ENG
Displays the average coverage of each color for the Vtref correction.
013-016 "Average L" is defined when the number of developed pages does not reach the number
specified with SP3-251-019.
013 Average L: Bk
*ENG
014 Average L: C
*ENG
015 Average L: M
*ENG
016 Average L: Y
*ENG
*ENG
[1 to 100 / 10 / 1 sheet/step]
*ENG
[1 to 500 / 10 / 1 sheet/step]
*ENG
[1 to 999 / 50 / 1 sheet/step]
182
*ENG
[1 to 100 / 20 / 1 sheet/step]
System SP3xxx
*ENG
[1 to 500 / 10 / 1 sheet/step]
*ENG
[1 to 999 / 50 / 1 sheet/step]
*ENG
*ENG
*ENG
*ENG
028
3311
*ENG
[0 to 100 / 20 / 1 %/step]
*ENG
*ENG
*ENG
*ENG
[0 to 5 / 0 / 0.01 V/step]
005-007 Displays the ID sensor (diffusion) offset voltage for Vsg adjustments.
005 Voffset dif: C
*ENG
*ENG
*ENG
3321
*ENG
*ENG
*ENG
183
3322
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3323
001 Ifsg: Bk
*ENG
002 Ifsg: C
*ENG
003 Ifsg: M
*ENG
004 Ifsg: Y
*ENG
*ENG
*ENG
*ENG
3324
[0 to 50 / 0 / 0.1 mA/step]
[0 to 50 / 0 / 0.1 mA/step]
184
*ENG
[0 to 99 / 0 / 0.1 time/step]
System SP3xxx
*ENG
[0 to 5 / 1 / 0.01 V/step]
*ENG
*ENG
001 Latest
*ENG
002 Latest 1
*ENG
003 Latest 2
*ENG
004 Latest 3
*ENG
005 Latest 4
*ENG
006 Latest 5
*ENG
007 Latest 6
*ENG
008 Latest 7
*ENG
009 Latest 8
*ENG
010 Latest 9
*ENG
3361
*ENG
[0 to 10 / 0 / 0.01 /step]
*ENG
*ENG
[0 to 10 / 5 / 0.01 /step]
*ENG
*ENG
*ENG
[0 to 1 / 1 / 0.01 /step]
3362
185
*ENG
*ENG
*ENG
*ENG
[0 to 1 / 0 / 0.01 /step]
*ENG
*ENG
*ENG
*ENG
3363
[0 to 1 / 1 / 1 /step]
0:Linear, 1: Curve
*ENG
*ENG
*ENG
*ENG
3371
186
*ENG
*ENG
*ENG
*ENG
System SP3xxx
*ENG
*ENG
*ENG
*ENG
3401
*ENG
*ENG
[0 to 100 / 5 / 1 %/step]
*ENG
*ENG
3411
001 Latest: Bk
*ENG
002 Latest: C
*ENG
003 Latest: M
*ENG
004 Latest: Y
*ENG
3421
[0 to 100 / - / 1 %/step]
*ENG
*ENG
*ENG
*ENG
187
*ENG
*ENG
*ENG
[0 to 1000 / 0 / 1 msec/step]
*ENG
3451
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
[0 to 10000 / 0 / 1 msec/step]
004 Y
*ENG
3452
001 Maximum: Bk
*ENG
002 Maximum: C
*ENG
003 Maximum: M
*ENG
004 Maximum: Y
*ENG
3501
*ENG
*ENG
*ENG
*ENG
3510
188
System SP3xxx
*ENG
*ENG
*ENG
*ENG
005 MUSIC: BW
*ENG
006 MUSIC: FC
*ENG
*ENG
*ENG
*ENG
*ENG
3511
[0 to 2000 / 0 / 1 page/step]
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 2000 / 0 / 1 page/step]
*ENG
019 Envir.Correction:ON/OFF
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 1 / 1 / 0.01/step]
[0 or 1 / 1 / 1 /step]
0: Not Correct (OFF),
1: Correct (ON)
189
*ENG
[0 to 1 / 0.5 / 0.01/step]
*ENG
[0 to 1 / 1 / 0.01/step]
*ENG
[0 to 1 / 0.1 / 0.01/step]
*ENG
[0 to 1 / 1 / 0.01/step]
*ENG
[0 to 1 / 0.25 / 0.01/step]
*ENG
[0 to 1 / 1 / 0.01/step]
*ENG
[0 to 99 / 2 / 1/step]
*ENG
[0 to 255 / 0 / 1/step]
Adjusts the timing for execution of process control and line position adjustment during printing
or copying.
*ENG
[0 to 100 / 5 / 1 page/step]
*ENG
[0 to 100 / 10 / 1 minute/step]
001 Year
*ENG
[0 to 99 / 0 / 1/step]
002 Month
*ENG
[1 to 12 / 1 / 1/step]
003 Date
*ENG
[1 to 31 / 1 / 1/step]
004 Hour
*ENG
[0 to 23 / 0 / 1/step]
005 Minute
*ENG
[0 to 59 / 0 / 1/step]
001 Temperature
190
*ENG
System SP3xxx
*ENG
[0 to 1000 / - / 0.1%RH/step]
*ENG
*ENG
*ENG
*ENG
*ENG
[Refresh Mode]
3516
While making prints with low coverage, the developer is agitated with less toner consumption
and the toner carrier attraction tends to increase. This may cause low image density or poor
transfer (white dots). To prevent this, the coagulated toner or overcharged toner has to be
consumed by performing the refresh mode.
*ENG
*ENG
*ENG
*ENG
*ENG
191
192
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
[0 to 2.55 / 1 / 0.01/step]
*ENG
*ENG
[0 to 100 / 30 / 1%/step]
*ENG
[0 to 100 / 19 / 1mm/step]
*ENG
[0 to 65535 / 0 / 1 cm2/step]
[0 to 255 / 49 / 1 cm2/m/step]
[0 to 255 / 25 / 1 cm2/m/step]
[0 to 255 / 0 / 1 time/step]
System SP3xxx
*ENG
*ENG
*ENG
[0 to 1000 / 0 / 1 page/step]
Adjusts the threshold temperature for preventing the cleaning blade in the transfer belt
cleaning unit from being damaged. If the temperature is above this value, toner is applied
to the transfer belt at set intervals during the job to prevent the blade from flipping over.
*ENG
[0 to 50 / 40 / 1C/step]
*ENG
*ENG
*ENG
[0 or 1 / 0 / 1/step]
*ENG
0: OFF. 1: ON
*ENG
*ENG
*ENG
008 MUSIC
*ENG
*ENG
*ENG
*ENG
[0 to 2 / 0 / 1/step]
0: OFF. 1: ON (once), 2: ON (twice)
[0 to 2 / 0 / 1/step]
0: OFF. 1: ON (once), 2: ON (twice)
[0 or 1 / 0 / 1/step]
0: OFF. 1: ON
[0 or 1 / 0 / 1/step]
Sets "1", when the following values shows.
*ENG
Vsg_reg_ave:
3.5 < Vsg_reg_ave < 4.5 or Vsg_dif_ave:
0.0 < Vsg_dif_ave < 0.5
193
3519
*ENG
[0 or 1 / 1 / 1/step]
002 MUSIC
*ENG
003 TC Adjustment
*ENG
3
3520
*ENG
*ENG
*ENG
[0 or 3 / 0 / 1 revolution/step]
*ENG
005 to
Adjusts the threshold temperature for entering the ITB idle rotation after the process control.
011
005 Temp. Range Thresh:T2
*ENG
[20 or 30 / 30 / 1 deg/step]
*ENG
[0 or 15 / 15 / 1 deg/step]
*ENG
[0 or 50 / 30 / 1 deg/step]
*ENG
[0 or 50 / 15 / 1 deg/step]
194
*ENG
*ENG
[0 to 99 / 10 / 1C/step]
*ENG
[0 to 99 / 50 / 1 %RH/step]
*ENG
[0 to 99 / 6 / 1 g/m3/step]
System SP3xxx
[Rapi Timer]
100 Time Setting
*ENG
[0 to 255 / 30 / 1 sec/step]
*ENG
*ENG
[0 to 99 / 10 / 1C/step]
*ENG
[0 to 99 / 50 / 1 %RH/step]
*ENG
[0 to 99 / 6 / 1 g/m3/step]
*ENG
[0 to 99 / 10 / 1 time/step]
3611
001 Bk (Current)
*ENG
002 C (Current)
*ENG
003 M (Current)
*ENG
004 Y (Current)
*ENG
*ENG
*ENG
*ENG
*ENG
195
*ENG
*ENG
*ENG
*ENG
3
013 Environmental Correction
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3612
196
[1 to 99 / 15 / 1 g/m3/step]
[Vk Display]
Displays Vk for each color.
001 Bk
*ENG
002 C
*ENG
003 M
*ENG
004 Y
*ENG
System SP3xxx
[Dev. DC Control:Display]
3621
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3622
3
[0 to 700 / 550 / 1 -V/step]
001 VB Limit
*ENG
[0 to 500 / 50 / 1 V/step]
197
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3641
*ENG
*ENG
*ENG
*ENG
198
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
System SP3xxx
3711
*ENG
[0 or 1 / 1 / - ]
0: Not Use, 1: Use
001 Vcnt
*ENG
[0 to 5 / 4 / 0.1 V/step]
002 Vt
*ENG
003 Sensitivity: HL
*ENG
004 Sensitivity: HM
*ENG
005 Sensitivity: ML
*ENG
*ENG
[0 to 5 / 1 / 0.1 V/step]
*ENG
*ENG
*ENG
*ENG
011 Adjustment: Vt
*ENG
*ENG
*ENG
[0 to 5 / 4 / 0.01 V/step]
*ENG
*ENG
[0 to 9 / 9 / 1 /step]
3712
[0 to 255 / - / 1 V/step]
[0 to 5 / 3 / 0.1 V/step]
[HST Control: C]
Displays the factory settings of the magenta PCU.
001 Vcnt
*ENG
[0 to 5 / 4 / 0.1 V/step]
199
002 Vt
*ENG
003 Sensitivity: HL
*ENG
004 Sensitivity: HM
*ENG
005 Sensitivity: ML
*ENG
*ENG
[0 to 5 / 1 / 0.1 V/step]
*ENG
*ENG
*ENG
*ENG
011 Adjustment: Vt
*ENG
*ENG
*ENG
[0 to 5 / 4 / 0.01 V/step]
*ENG
*ENG
[0 to 9 / 9 / 1 /step]
3713
200
[0 to 255 / - / 1 V/step]
[0 to 5 / 3 / 0.1 V/step]
[HST Control: M]
Displays the factory settings of the cyan PCU.
001 Vcnt
*ENG
[0 to 5 / 4 / 0.1 V/step]
002 Vt
*ENG
003 Sensitivity: HL
*ENG
004 Sensitivity: HM
*ENG
005 Sensitivity: ML
*ENG
*ENG
[0 to 5 / 1 / 0.1 V/step]
*ENG
*ENG
System SP3xxx
*ENG
*ENG
011 Adjustment: Vt
*ENG
*ENG
*ENG
[0 to 5 / 4 / 0.01 V/step]
*ENG
*ENG
[0 to 9 / 9 / 1 /step]
3714
[0 to 255 / - / 1 V/step]
[0 to 5 / 3 / 0.1 V/step]
[HST Control:Y]
Displays the factory settings of the yellow PCU.
001 Vcnt
*ENG
[0 to 5 / 4 / 0.1 V/step]
002 Vt
*ENG
003 Sensitivity: HL
*ENG
004 Sensitivity: HM
*ENG
005 Sensitivity: ML
*ENG
*ENG
[0 to 5 / 1 / 0.1 V/step]
*ENG
*ENG
*ENG
*ENG
011 Adjustment: Vt
*ENG
*ENG
*ENG
[0 to 5 / 4 / 0.01 V/step]
*ENG
*ENG
[0 to 9 / 9 / 1 /step]
[0 to 255 / - / 1 V/step]
[0 to 5 / 3 / 0.1 V/step]
201
3800
*CTL
[0 to 4 / 0 / 1 /step]
001 Displays the current condition of the PCDU toner collection bottle.
0: Factory default, 1: Before near full, 2; Near full, 3: Full, 4: Reserved
*CTL
*CTL
*CTL
Not used
[0 to 50 / - / 1 /step]
Not used
[0 to 2000 / 0 / 1 sheet/step]
Not used
[0 to 200000 / - / 1 cm2/step]
Not used
*CTL
008
Coefficient
*ENG
Adjusts the toner amount between near full and full. (0.1 indicates 10%.)
Enables or disables the calling for @Remote.
Alarm Setting
*ENG
[0 or 1 / 1 / - ]
0: Enable @Remote calling
1: Disable @Remote calling
011
NOTE:
If the PCDU toner collection bottle has been replaced before the machine detects used toner
near full when this setting is set to "0", the machine cannot detect toner collection bottle near
full. In that case, set SP3-902-017 to "1".
Day Thresh:NF
*ENG
[1 to 30 / 10 / 1 day/step]
012 Sets the threshold days for the near-full display. The near-full of the PCDU toner collection
bottle is displayed after the toner collection full sensor has detected the actuator in the PCDU
toner collection bottle.
202
System SP3xxx
*ENG
3810
*ENG
*CTL
[0 to 4 / 0 / 1 /step]
001 Displays the current condition of the ITB toner collection bottle.
0: Factory default, 1: Before near full, 2; Near full, 3: Full, 4: Reserved
002 Detection Times
*CTL
*CTL
*CTL
Not used
[0 to 50 / - / 1 /step]
Not used
[0 to 2000 / 0 / 1 sheet/step]
Not used
[0 to 200000 / - / 1 cm2/step]
Not used
*CTL
008
Coefficient
*ENG
Adjusts the toner amount between near full and full. (0.1 indicates 10%.)
Enables or disables the calling for @Remote.
Alarm Setting
*ENG
[0 or 1 / 1 / - ]
0: Enable @Remote calling
1: Disable @Remote calling
011
NOTE:
If the toner collection bottle has been replaced before the machine detects used toner near
full when this setting is set to "0", the machine cannot detect toner collection bottle near full.
In that case, set SP3-902-017 to "1".
203
Day Thresh:NF
*ENG
[1 to 30 / 10 / 1 day/step]
012 Sets the threshold days for the near-full display. The near-full of the IT toner collection bottle
is displayed after the toner collection full sensor has detected the actuator in the ITB toner
collection bottle.
*ENG
3901
*ENG
*ENG
[0 or 1 / 1 / - ]
0: OFF, 1: ON
204
Turns the new unit detection flag for each PM unit on or off.
The use of these counters is explained in the PM section and in the relevant parts of section
3 (Replacement and Adjustment).
*ENG
*ENG
[0 or 1 / 0 / - ]
*ENG
0: OFF, 1: ON
*ENG
005 Developer: Bk
*ENG
006 Developer: C
*ENG
007 Developer: M
*ENG
008 Developer: Y
*ENG
Not used
[0 or 1 / 0 / - ]
0: OFF, 1: ON
System SP3xxx
009 PCU: Bk
*ENG
010 PCU: C
*ENG
[0 or 1 / 0 / - ]
011 PCU: M
*ENG
0: OFF, 1: ON
012 PCU: Y
*ENG
*ENG
*ENG
0: OFF, 1: ON
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
3903
[0 or 1 / 0 / - ]
[0 or 1 / 0 / - ]
0: OFF, 1: ON
205
001 Counter 1
*ENG
002 Counter 2
*ENG
003 Counter 3
*ENG
004 Counter 4
*ENG
005 Counter 5
*ENG
006 Counter 6
*ENG
007 Counter 7
*ENG
008 Counter 8
*ENG
009 Counter 9
*ENG
010 Counter 10
*ENG
011040
Counter 11 to 40
206
[0 to 999999999 / - / 1 mm/step]
*ENG
*ENG
*ENG
System SP4xxx
System SP4xxx
SP4-XXX (Scanner)
4008
*ENG
Adjusts the leading edge registration by changing the scanning start timing in the sub-scan
direction.
*ENG
Adjusts the side-to-side registration by changing the scanning start timing in the main scan
direction.
*ENG
Sets the blank margin at each side for erasing the original shadow caused by the gap
between the original and the scale.
*ENG
*ENG
207
Performs the scanner free run with the exposure lamp on or off in the following mode.
Full color mode / Full Size / A3 or DLT
4014
*ENG
[0 or 1 / 0 / - ]
0: OFF, 1: ON
[Scan]
Execute the scanner free fun with each mode.
4020
[Dust Check]
Turns the ADF scan glass dust check on/ off.
*ENG
[0 or 1 / 1 / 1 /step]
0: OFF, 1: ON
Selects the detect level.
*ENG
[0 to 8 / 4 / 1 /step]
0: lowest detection level
8: highest detection level
Selects the level of the sub scan line correction
when using the ARDF.
[0 to 4 / 0 / 1 /step]
*ENG
0: Off
1: Weakest
2: Weak
3: Strong
4: Strongest
208
System SP4xxx
Displays a code that represents the original size detected by the original sensors. (See "Input
Check Table".)
4303
*ENG
0: No Original
1: A5-Lengthwise (16K SEF if 4305 is set to 3)
[0 to 3 / 0 / 1 /step]
4305
[8K/16K Detection]
*ENG
001 This program enables the machine to automatically recognize the 8K/16K size.
4308
4309
*ENG
[0 or 1 / 1 / 1 /step]
0: OFF, 1: ON
*ENG
*ENG
*ENG
4310
001 S1:R
002 S1:G
003 S1:B
004 S2:R
005 S2:G
006 S2:B
007 S3:R
008 S3:G
009 S3:B
*ENG
4417
210
[0 to 24 / 0 / 1/step ]
System SP4xxx
0: Scanned image
6: Grid pattern
8: Gradation RGBCMYK
9: UCR pattern
001 Copy
002 Scanner
*ENG
[0 to 3 / 3 / 1 /step]
003 Fax
4440
[Saturation Adjustment]
Adjusts the level of saturation for copying.
[0 to 5 / 3 / 1 /step]
0: High
1: Lowest
001 -
*ENG
2: Lower
3: Default
4: Higher
5: Highest
4450
211
001
002
[0 or 1 / 1 / - ] 0: OFF, 1: ON
4460
*ENG
*ENG
4501
*ENG
*ENG
*ENG
*ENG
[0 to 10 / 5 / 1 /step]
*ENG
*ENG
*ENG
*ENG
4505
212
Specifies the level of deleting the background in the ADS mode. You can adjust its level for
each scanning method (platen, ADF).
[ACC Correction:Bright]
Adjusts the offset correction for light areas of the ACC pattern.
System SP4xxx
001 Text:K
*ENG
002 Text:C
*ENG
003 Text:M
*ENG
004 Text:Y
*ENG
005 Photo:K
*ENG
006 Photo:C
*ENG
007 Photo:M
*ENG
008 Photo:Y
*ENG
4506
001 Text:K
*ENG
002 Text:C
*ENG
003 Text:M
*ENG
004 Text:Y
*ENG
005 Photo:K
*ENG
006 Photo:C
*ENG
007 Photo:M
*ENG
008 Photo:Y
*ENG
This SP corrects the printer coverage of 12 hues (RY, YR, YG, etc. x 4 Colors [R, G, B,
Option]) for a total of 48 parameters.
213
*ENG
4551
4552
4553
4554
4565
4570
4571
4572
-005
*ENG
[0 to 15 / 8 / 1 /step]
0: MTF Off
Sets the MTF level (Modulation Transfer Function) designed to improve image contrast. Set
higher for stronger effect, lower for weaker effect.
214
System SP4xxx
-006
-007
-008
*ENG
[0 to 7 / 4 / 1 /step]
Use to remove "jaggies" if they appear. Set higher for smoother images.
Brightness: 1255
*ENG
*ENG
Set higher for more contrast, set lower for less contrast.
I-Dot Erase :0 (x1) 1-7 (Strong)
*ENG
[0 to 7 / 0 / 1 /step]
-009 Sets the erasure level of Irregular Dots. Set higher for stronger effect, lower for weaker effect.
0: Not activated
4580
4582
4583
*ENG
-005
[0 to 15 / 8 / 1 /step]
0: MTF Off
Sets the MTF level (Modulation Transfer Function) designed to improve image contrast. Set
higher for stronger effect, lower for weaker effect.
-006
-007
-008
*ENG
[0 to 7 / 4 / 1 /step]
Use to remove "jaggies" if they appear. Set higher for smoother images.
Brightness: 1255
*ENG
*ENG
Set higher for more contrast, set lower for less contrast.
I-Dot Erase:0 (x1), 1-7 (Strong)
*ENG
[0 to 7 / 0 / 1 /step]
-009 Selects the contrast level for B/W the Text mode. Sets the erasure level of Irregular Dots. Set
higher for stronger effect, lower for weaker effect.
0: Not activated
215
*ENG
[0 to 2 / 0 / 1 /step]
-010 Sets the erasure level of textures. Set higher for stronger effect, lower for weaker effect. This
SP (suffix "-010") only exists in SP4580, 4582 and 4583.
0: Not activated
4581
4584
4585
*ENG
-005
[0 to 15 / 8 / 1 /step]
0: MTF Off
Sets the MTF level (Modulation Transfer Function) designed to improve image contrast. Set
higher for stronger effect, lower for weaker effect.
-006
-007
-008
*ENG
[0 to 7 / 4 / 1 /step]
Use to remove "jaggies" if they appear. Set higher for smoother images.
Brightness: 1255
*ENG
*ENG
Set higher for more contrast, set lower for less contrast.
I-Dot Erase:0 (x1), 1-7 (Strong)
*ENG
[0 to 7 / 0 / 1 /step]
-009 Selects the contrast level for B/W the Text mode. Sets the erasure level of Irregular Dots. Set
higher for stronger effect, lower for weaker effect.
0: Not activated
4600
216
001 SBU ID
002 GASBU-N ID
[0 to 0xFF / 0 / 1 /step]
003 VSP5100 ID
[0 to 0xFF / 0 / 1 /step]
System SP4xxx
4602
[0 or 1 / 0 / 1/step] DFU
4603
4604
[AGC Execution]
001 -
[0 or 1 / 0 / 1/step]
0: OFF, 1: ON
4609
*ENG
002 DF Scan
*ENG
*ENG
002 DF Scan
*ENG
*ENG
002 DF Scan
*ENG
4610
4611
4623
217
3
4624
4625
4628
[0 to 7 / 0 / 1 digit/step]
System SP4xxx
4629
4630
Displays the gain value of the amplifiers on the controller for Blue.
-
[0 to 1023 / 0 / 1 digit/step]
[0 to 1023 / 0 / 1 digit/step]
4645
Displays the gain value of the amplifiers on the controller for Red.
-
4633
[0 to 7 / 0 / 1 digit/step]
4632
[0 to 7 / 0 / 1 digit/step]
4631
[0 to 1023 / 0 / 1 digit/step]
[0 to 65535 / 0 / 1 digit/step]
219
4647
001 Power-ON
4654
001
*ENG
*ENG
4655
001
*ENG
002
*ENG
4656
220
System SP4xxx
001
*ENG
002
*ENG
4658
4659
*ENG
[0 to 7 / 0 / 1 digit/step]
[0 to 7 / 0 / 1 digit/step]
*ENG
*ENG
4662
[0 to 7 / 0 / 1 digit/step]
Displays the previous gain value of the amplifiers on the controller for Green.
4661
*ENG
4660
[0 to 1023 / 0 / 1 digit/step]
*ENG
*ENG
[0 to 1023 / 0 / 1 digit/step]
221
4663
*ENG
*ENG
4673
[0 to 1023 / 0 / 1 digit/step]
*ENG
*ENG
4674
*ENG
*ENG
4675
222
System SP4xxx
*ENG
*ENG
4677
4678
*ENG
[0 to 7 / 0 / 1 digit/step]
[0 to 7 / 0 / 1 digit/step]
*ENG
*ENG
4681
[0 to 7 / 0 / 1 digit/step]
Displays the factory setting values of the gain adjustment for Green.
4680
*ENG
4679
[0 to 1023 / 0 / 1 digit/step]
223
*ENG
*ENG
4682
[0 to 1023 / 0 / 1 digit/step]
*ENG
*ENG
[0 to 1023 / 0 / 1 digit/step]
Adjusts the white shading parameter when scanning an image with the ARDF.
Adjusts the density level if the ID of outputs made in the DF and Platen mode is different.
001 -
4690
002 RO
[0 to 1023 / 0 / 1 digit/step]
001 GE
002 GO
4692
001 RE
4691
224
*ENG
[0 to 1023 / 0 / 1 digit/step]
001 BE
002 BO
[0 to 1023 / 0 / 1 digit/step]
System SP4xxx
4693
001 RE
002 RO
4694
001 GE
002 GO
4695
002 BO
[0 to 1023 / 0 / 1 digit/step]
001 4806
[0 to 1023 / 0 / 1 digit/step]
4804
001 BE
4802
[0 to 1023 / 0 / 1 digit/step]
[Carriage Move]
Moves the carriage from the scanner home position.
001 -
225
4807
[0 to 255 / 0 / 1 /step]
*ENG
[0 or 1 / 0 / 1 /step]
This SP outputs the final data read at the end of ACC execution.
A zero is returned if there was an error reading the data.
[0 to 255 / 0 / 1 /step]
001 R DATA1
*ENG
002 G DATA1
*ENG
003 B DATA1
*ENG
004 R DATA2
*ENG
005 G DATA2
*ENG
006 B DATA2
*ENG
4904
226
System SP4xxx
Test1
Performs a write and read check of the ASICs on the BCU board and displays the result.
Test2
Performs an image path check on the BCU board and displays the result.
4905
001 4918
[0 to 255 / 0 / 1 /step]
009 -
4948
*ENG
[ACC History:Latest]
001 YY/MM/DD
*ENG
002 HH/MM/SS
*ENG
227
4949
001 YY/MM/DD
*ENG
002 HH/MM/SS
*ENG
4954
[ACC History:Previous]
[Read/Restore Standard]
[0 to 11 / 2 / 1 /step ]
228
System SP4xxx
*ENG
[0 to 9 / 4 / 1 /step]
0: weakest sensitivity
9: strongest sensitivity
Selects the range level of Highlight correction.
*ENG
[0 to 9 / 4 / 1 /step]
0: weakest skew correction,
9: strongest skew correction
4994
*ENG
0: Text priority
1: Normal
2: Photo priority
Selects the threshold level of the original background density. Increasing this threshold level
machine easily judge that an original is white.
[0 to 6 / 3 / 1 /step]
001 -
*ENG
0: lightest
6: Darkest
229
System SP5xxx
SP5-XXX (Mode)
5024
*CTL
0: mm (Europe/Asia)
1: inch (USA)
[Accounting Counter]
5045
*CTL
0: Developments
1: Prints
5047
[Paper Display]
Turns on or off the printed paper display on the LCD.
5051
*CTL
[0 or 1 / 0 / - ]
0: OFF, 1: ON
5051 1 -
*CTL
0: ON
1: OFF
5055
230
[Display IP Address]
Display or does not display the IP address on the LCD.
System SP5xxx
001 -
5056
0: OFF 1: ON
[0 or 1 / 0 / - ]
0: Not display, 1: Display
001 -
5062
[0 or 1 / 0 / - ]
001 -
5061
*CTL
*CTL
[0 or 1 / 0 / - ]
0: Not display, 1: Display
001 PCU:Bk
*CTL
002 PCU:M
*CTL
003 PCU:C
*CTL
004 PCU:Y
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
[0 or 1 / 0 / - ]
0: No Display, 1: Display
231
5063
001
[Small Tray]
-
*CTL
[0 or 1 / 0 / - ]
0: Normal Tray, 1: Envelope Feeder
001 -
*CTL
[0 or 1 / 0 / - ]
0: No Display, 1: Display
001 PCU:Bk
*CTL
002 PCU:M
*CTL
003 PCU:C
*CTL
004 PCU:Y
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
5071
232
System SP5xxx
001
5104
*CTL
[0 or 1 / 0 / -]
0: Off, 1: On
Turn on or off the paper size confirmation pop-up on the LED. This pop-up prevents
mismatching between a paper size selected by the operation panel and an actual paper
size on the by-pass tray.
[A3/DLT Double Count] SSP
[0 to 2 / 0 / 1/step]
PCU:Bk
*CTL
001
0: No
1: Yes
2: Yes except By-pass
Specifies whether the counter is doubled for A3/DLT. "Yes" counts except from the bypass
tray. When "Yes" is selected, A3 and DLT paper are counted twice, that is A4 x2 and LT x2
respectively.
5113
001
*CTL
0: None
*CTL
1: Expansion Device 1
2: Expansion Device 2
3: Expansion Device 3
5114
*CTL
233
5118
[Disable Copying]
*CTL
*CTL
5120
001
3
5121
001
This program updates the information on the optional counter. When you install or remove
an optional counter, check the settings.
[Counter Up Timing]
*CTL
This program specifies when the counter goes up. The settings refer to "paper feed" and
"paper exit" respectively.
[0 to 2 / 0 / 1 /step]
5126
*ENG
[APS Mode]
*CTL
*CTL
001 DFU
5131
001
5150
234
*ENG
DFU
[0: JP (Japan)/ 1: NA / 2: EU]
The program selects a paper size system from the following alternatives: the AB system (0),
the LT system (1), and the AF system (2).
[By-Pass Length Setting]
*CTL
System SP5xxx
Determines whether the transfer sheet from the by-pass tray is used or not.
001 Normally the paper length for sub scanning paper from the by-pass tray is limited to 600
mm, but this can be extended with this SP to 1260 mm.
5162
*CTL
001 This program specifies the switch that selects an application program.
[Fax Printing Mode at Optional Counter Off]
5167
Enables or disables the automatic print out without an accounting device. This SP is used
when the receiving fax is accounted by an external accounting device.
[0 or 1 / 0 / - ]
0: Automatic printing
1: No automatic printing
[CE Login]
5169
If you will change the printer bit switches, you must log in to service mode with this SP before
you go into the printer SP mode.
[0 or 1 / 0 / - ]
001 -
*CTL
0: Disabled
1: Enabled
5181
[Size Adjust]
Adjusts the paper size for each tray.
*ENG
002 Tray 1: 2
*ENG
003 Tray 1: 3
*ENG
004 Tray 1: 4
*ENG
005 Tray 2: 1
*ENG
006 Tray 2: 2
*ENG
007 Tray 2: 3
*ENG
008 Tray 2: 4
*ENG
009 Tray 3: 1
*ENG
010 Tray 3: 2
*ENG
011 Tray 3: 3
*ENG
012 Tray 3: 4
*ENG
013 Tray 4: 1
*ENG
014 Tray 4: 2
*ENG
015 Tray 4: 3
*ENG
016 Tray 4: 4
*ENG
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A4 LEF, 1: LT LEF
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A3, 1: DLT
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B4, 1: LG
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B5 LEF, 1: Exe LEF
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A4 LEF, 1: LT LEF
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A3, 1: DLT
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B4, 1: LG
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B5 LEF, 1: Exe LEF
[0 to 2 / 0 (EU/ASIA), 1 (NA) / - ]
0: A4LEF, 1: LTLEF
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: A3, 1: DLT
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B4, 1: LG
[0 or 1 / 0 (EU/ASIA), 1 (NA) / - ]
0: B5 LEF, 1: Exe LEF
236
System SP5xxx
[0 or 1 / 0 / 1/step]
001 -
*ENG
0: Disable
1: Enable
5188
[Copy NV Version]
Displays the version number of the NVRAM on the controller board.
001 5195
*CTL
*CTL
0: Productivity priority
1: Tray priority
*CTL
Not used
*CTL
Not used
5199
001 -
*CTL
[ 0 or 1 / 0 / -]
0: OFF, 1: ON
237
Enables or disables the paper feeding out from the finisher without stapling.
If this setting is "1: ON", paper is fed out without stapling at the maximum number of
the finisher stapling when the machine gets a multiple printing job (over maximum
number).
If this setting is "0: OFF", paper is fed out with stapling at the maximum number of the
finisher stapling when the machine gets a multiple printing job (over maximum number).
5212
[Page Numbering]
*CTL
This program adjusts the position of the second side page numbers.
A " value" moves the page number positions to the left edge.
A "+ value" moves the page number positions to the right edge.
003 Duplex Printout Right/Left Position
004 Duplex Printout High/Low Position
[10 to 10 / 0 / 1 mm/step]
[Set Time]
Adjusts the RTC (real time clock) time setting for the local time zone.
Examples: For Japan (+9 GMT), enter 540 (9 hours x 60 min.)
DOM: +540 (Tokyo)
5302
238
[Summer Time]
*CTL#
System SP5xxx
0: Disabled
1: Enabled
NA and EUR: 1, ASIA: 0
[Access Control]
5401
When installing the SDK application, SAS (VAS) adjusts the following settings. DFU
Whenever a new login user is added to the
address book in external certification mode (for
Windows, LDAP, RDH), the default document
ACL is updated according to this SP setting.
[0 to 3 / 0 / 1]
103 Default Document ACL
*CTL
0: View
1: Edit
2: Edit/Delete
3: Full control
Note: This SP setting is ignored on a machine that
is not using document server.
[0 to 255 / 0 / 1 sec./step]
104
Authentication Time
*CTL
0: 60 seconds
1 to 250 seconds
*CTL
240
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
System SP5xxx
*CTL
230
*CTL
240
5404
5411
*CTL
*CTL
[LDAP Certification]
[0 to 1 / 1 / 1] 1: On, 0: Off
This SP is referenced only when SP5411-4 is set
to "1" (On).
005 Password Null Not Permit
*CTL
[0 to 1 / 0 / 1]
0: Password NULL not permitted.
1: Password NULL permitted.
*CTL
241
5413
[Lockout Setting]
*CTL
*CTL
*CTL
[0 to 1 / 0 / 1]
0: Off (no wait time, lockout not cancelled)
1: On (system waits, cancels lockout if correct
user ID and password are entered.
*CTL
*CTL
Not Used
[Access Mitigation]
Switches on/off masking of continuously used
IDs and passwords that are identical.
001 Mitigation On/Off
*CTL
[0 to 1 / 0 /1]
0: Off
1: On
*CTL
5415
242
[Password Attack]
System SP5xxx
*CTL
*CTL
5416
[Access Information]
*CTL
*CTL
*CTL
5417
[Access Attack]
*CTL
*CTL
*CTL
243
*CTL
[User Authentication]
5420
001 Copy
*CTL
*CTL
Enables or disables the color copy limitation for each copy mode when the user
authentication is "ON".
0: Enable (default), 1: Disable
002
*CTL
021 Fax
*CTL
244
System SP5xxx
031 Scanner
*CTL
041 Printer
*CTL
051 SDK1
[0 or 1 / 0 / 1] 0: ON. 1: OFF
061 SDK2
*CTL
071 SDK3
5430
*CTL
*CTL
*CTL
5431
010
Tag
*CTL
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the tag copy permission for the external authentication.
011
Entry
*CTL
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the entry information for the external authentication.
245
012
Group
*CTL
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the group information for the external authentication.
020
*CTL
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the mail information for the external authentication.
3
030
Fax
*CTL
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the fax information for the external authentication.
FaxSub
*CTL
031
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the fax additional information for the external
authentication.
032
Folder
*CTL
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the folder information for the external authentication.
ProtectCode
*CTL
033
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the protection code information for the external
authentication.
034
SmtpAuth
*CTL
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the SMTP information for the external authentication.
035
LdapAuth
*CTL
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the LDAP information for the external authentication.
246
System SP5xxx
*CTL
036
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the SMB/FTP information for the external
authentication.
AcntAcl
*CTL
037
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the account ACL information for the external
authentication.
DocumentAcl
*CTL
038
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the document ACL information for the external
authentication.
[0 or 1 / 1 / -]
CertCrypt
040
Turns on or off the copy permission of the authentication information for the external
authentication.
UserLimitCount
*CTL
050
[0 or 1 / 1 / -]
0: Not permit, 1: Permit
Turns on or off the copy permission of the maximum number information for the external
authentication.
5481
*CTL
247
*CTL
5490
*CTL
*CTL
[PM Alarm]
[0 to 9999 / 0 / 1 / step]
001 PM Alarm Level
*CTL
0: Alarm off
1 to 9999: Alarm goes off when Value (1 to
9999) x 1000 > PM counter
[0 or 1 / 1 / -]
5504
[Jam Alarm]
*CTL
*CTL
0: No alarm sounds
1: Alarm sounds after the number of originals
passing through the ARDF > 10,000
-
Sets the alarm to sound for the specified jam level (document misfeeds are not included).
[0 to 3 / 3 / 1 /step]
001
0: Zero (Off)
1: Low (2.5K jams)
2: Medium (3K jams)
3: High (6K jams)
248
System SP5xxx
[Error Alarm]
Sets the error alarm level.
The error alarm counter counts "1" when any SC is detected. However, the error alarm
counter decreases by "1" when an SC is not detected during a set number of copied sheets
(for example, default 1500 sheets).
5505
The error alarm occurs when the SC error alarm counter reaches "5".
001 [Supply Alarm]
5507
*CTL
*CTL
0: Off, 1: On
0: Off, 1: On
0: Off, 1: On
[CC Call]
*CTL
249
001*
002*
003*
3
011*
012*
013*
Jam Remains
0: Disable, 1: Enable
0: Disable, 1: Enable
0: Disable, 1: Enable
[3 to 30 / 10 / 1 minute /step]
Sets the time a jam must remain before it becomes an "unattended paper jam".
Jam Detection: Continuous Count
[2 to 10 / 5 / 1 /step]
[3 to 30 / 10 / 1 /step]
Sets the length of time the door remains open before the machine initiates a call.
[SC/Alarm Setting]
5515
With @Remote in use, these SP codes can be set to issue an SC call when an SC error
occurs. If this SP is switched off, the SC call is not issued when an SC error occurs.
001 SC Call
002 Service Parts Near End Call
003 Service Parts End Call
004 User Call
250
[0 or 1 / 1 / - ]
0: Off
1: On
System SP5xxx
[0 or 1 / 1 / - ]
0: Off
1: On
5516
*CTL
With @Remote in use, these SP codes can be set to issue an PM alarm call when one of SP
parts reaches its yield.
001
[0 or 1 / 1 / - ]
0: Not send, 1: Send
[1 to 255 / 75 / 1 %/step]
005
006
5611
Overwrites the current values onto the factory settings of the base gamma control points.
Restore Prev. Setting
001
B-C
*ENG
Adjusts the Cyan correction value of the blue signal in two-color mode.
251
002
B-M
*ENG
Adjusts the Magenta correction value of the blue signal in two-color mode.
003
G-C
*ENG
Adjusts the Cyan correction value of the blue signal in two-color mode.
3
004
G-Y
*ENG
Adjusts the Yellow correction value of the blue signal in two-color mode.
005
R-M
*ENG
Adjusts the Magenta correction value of the blue signal in two-color mode.
006
R-Y
*ENG
Adjusts the Yellow correction value of the blue signal in two-color mode.
5618
*CTL
252
System SP5xxx
001
5801
*CTL
[0 or 1 / 0 / -]
0: Disabled, 1: Enabled
[Memory Clear]
001 All Clear
003 SCS
005 MCS
Initializes the fax reset time, job login ID, all TX/RX settings,
local storage file numbers, and off-hook timer.
Initializes the scanner defaults for the scanner and all the
scanner SP modes.
253
011 NCS
012 R-FAX
017 CCS
019 LCS
021 ECS
5803
[Input Check]
5804
[Output Check]
5806
[RFID CONT.READING]
001
002
003
254
TIMES
[0 to 65535 / - / 1 /step]
[0 to 65535 / - / 1 /step]
[0 to 65535 / - / 1 /step]
004 EXE.ALL
005 EXE.K
System SP5xxx
006 EXE.M
007 EXE.C
008 EXE.Y
[SC Reset]
5810
5811
*ENG
-
005 FRAM
5812
*CTL
001 Sets the telephone number for a service representative. This number is printed on the
Counter List, which can be printed with the users "Counter" menu.
This can be up to 20 characters (both numbers and alphabetic characters can be input).
Facsimile
*CTL
002 Sets the fax or telephone number for a service representative. This number is printed on the
Counter List.
This can be up to 20 characters (both numbers and alphabetic characters can be input).
Supply
*CTL
003 Use this to input the telephone number of your supplier for consumables. Enter the number
and press #.
255
Operation
*CTL
004 Use this to input the telephone number of your sales agency. Enter the number and press
#.
5816
[Remote Service]
*CTL
I/F Setting
[0 to 2 / 2 / 1 /step]
0: Remote service off
1: CSS remote service on
2: @Remote service on
CE Call
Performs the CE Call at the start or end of the service.
002
[0 or 1 / 0 / 1 /step]
0: Start of the service
1: End of the service
NOTE: This SP is activated only when SP 5816-001 is set to "2".
Function Flag
256
System SP5xxx
013 [0 or 1 / 1 / ]
0: RFU is executed whenever update request is received.
1: RFU is executed only when the machine is in the sleep mode.
RCG C Registed
021
257
061
062 This SP setting determines if the proxy server is used when the machine communicates with
the service center.
Proxy Host
3
063
This SP sets the address of the proxy server used for communication between Embedded
RC Gate-N and the gateway. Use this SP to set up or display the customer proxy server
address. The address is necessary to set up Embedded RC Gate-N.
The address display is limited to 128 characters. Characters beyond the 128
character are ignored.
This address is customer information and is not printed in the SMC report.
Proxy Port Number
This SP sets the port number of the proxy server used for communication between Embedded
064 RC Gate-N and the gateway. This setting is necessary to set up Embedded RC Gate-N.
This port number is customer information and is not printed in the SMC report.
Proxy User Name
This SP sets the HTTP proxy certification user name.
065
The length of the name is limited to 31 characters. Any character beyond the 31st
character is ignored.
This name is customer information and is not printed in the SMC report.
Proxy Password
This SP sets the HTTP proxy certification password.
066
The length of the password is limited to 31 characters. Any character beyond the 31st
character is ignored.
This name is customer information and is not printed in the SMC report.
258
System SP5xxx
067
CERT: Up State
Displays the status of the certification update.
0
The certification request (setAuthKey) for update has been received from the GW
URL and certification is presently being updated.
The certification update is completed and the GW URL is being notified of the
successful update.
The certification update failed, and the GW URL is being notified of the failed update.
The period of the certification has expired and new request for an update is being
sent to the GW URL.
11
A rescue update for certification has been issued and a rescue certification setting
is in progress for the rescue GW connection.
12
The rescue certification setting is completed and the GW URL is being notified of the
certification update request.
13
The notification of the request for certification update has completed successfully,
and the system is waiting for the certification update request from the rescue GW
URL.
14
The notification of the certification request has been received from the rescue GW
controller, and the certification is being stored.
15
The certification has been stored, and the GW URL is being notified of the successful
completion of this event.
16
The storing of the certification has failed, and the GW URL is being notified of the
failure of this event.
17
The certification update request has been received from the GW URL, the GW URL
was notified of the results of the update after it was completed, but a certification
error has been received, and the rescue certification is being recorded.
18
The rescue certification of No. 17 has been recorded, and the GW URL is being
notified of the failure of the certification update.
CERT: Error
068 Displays a number code that describes the reason for the request for update of the
certification.
259
260
Request for certification update in progress. The current certification has expired.
An SSL error notification has been issued. Issued after the certification has expired.
069 CERT: Up ID
System SP5xxx
Displays the start time of the period for which the current
@Remote certification is enabled.
Displays the end time of the period for which the current
@Remote certification is enabled.
150
151
152
153
154
156
157
161
162
163
Selection Country
Not used
Line Type Automatic Judgment
Not used
Line Type Judgment Result
Not used
Selection Dial/Push
Not used
Outside Line/Outgoing Number
Not used
Dial Up User Name
Not used
Dial Up Password
Not used
Local Phone Number
Not used
Connection Timing Adjustment: Incoming
Not used
Access Point
Not used
261
164
Line Connecting
Not used
187
Not used
Retransmission Limit
Not used
FAX TX Priority
Not used
Not used
Regist: Status
Displays a number that indicates the status of the @Remote service device.
0: Neither the @Remote device nor Embedded RCG Gate is set.
1: The Embedded RCG Gate is being set. Only Box registration is completed. In this status,
201 @Remote device cannot communicate with this device.
2: The Embedded RCG Gate is set. In this status, the @Remote device cannot communicate
with this device.
3: The @Remote device is being set. In this status the Embedded RCG Gate cannot be set.
4: The @Remote module has not started.
202 Letter Number
262
System SP5xxx
Displays a number that indicates the result of the confirmation executed with SP5816-203.
0: Succeeded
1: Confirmation number error
2: Registration in progress
3: Proxy error (proxy enabled)
4: Proxy error (proxy disabled)
5: Proxy error (Illegal user name or password)
6: Communication error
7: Certification update error
8: Other error
9: Confirmation executing
Confirm Place
205 Displays the result of the notification sent to the device from the Gateway in answer to the
confirmation request. Displayed only when the result is registered at the Gateway.
206 Register Execute
Register Result
Displays a number that indicates the registration result.
0: Succeeded
2: Registration in progress
3: Proxy error (proxy enabled)
207 4: Proxy error (proxy disabled)
5: Proxy error (Illegal user name or password)
6: Communication error
7: Certification update error
8: Other error
9: Registration executing
Error Code
208 Displays a number that describes the error code that was issued when either SP5816-204
or SP5816-207 was executed.
263
Cause
264
Code
Meaning
-11001
-11002
-11003
Unexpected error
-12002
-12003
-12004
-12005
-12006
-12007
-12008
-12009
-12010
-2385
-2387
-2389
-2390
-2391
-2392
Parameter error
System SP5xxx
-2393
-2394
-2395
-2396
-2397
-2398
5821
NOTE: Turn off and on the main power switch after this
setting has been changed.
*CTL
Uploads the UP and SP mode data (except for counters and the serial number) from the
NVRAM to an SD card. For details, see the "NVRAM Data Upload/Download" in the
"System Maintenance Reference" of the Field Service Manual.
001 -
Downloads the UP and SP mode data from an SD card to the NVRAM. For details, see the
"NVRAM Data Upload/Download" in the "System Maintenance Reference" of the Field
Service Manual.
001 -
5828
[Network Setting]
*CTL
265
[0 or 1 / 1 / 1 / step]
0: Disabled, 1: Enabled
Enables or disables ECP Compatibility.
[0 or 1 / 1 / 1 / step]
0: Disabled, 1: Enabled
This SP is activated only when SP5-828-50 is set to
"1".
Enables/disables Job Spooling.
[0 or 1 / 0 / 1 / step]
0: Disabled, 1: Enabled
bit1: FTP
bit2: IPP
bit3: SMB
bit4: BMLinkS
bit5: DIPRINT
bit6: sftp
bit7: (Reserved)
Enables or disables the Telnet protocol.
[0 or 1 / 1 / ]
0: Disable, 1: Enable
266
System SP5xxx
[0 or 1 / 1 / ]
0: Disable, 1: Enable
This is the IPv6 local address link referenced on the
Ethernet or wireless LAN (802.11b) in the format:
145 Active IPv6 Link Local Address "Link Local Address" + "Prefix Length"
The IPv6 address consists of a total 128 bits configured
in 8 blocks of 16 bits each.
147
149
151
[0 or 1 / 1 / 1 /step]
0: Disable, 1: Enable
267
5832
268
Same as "-239"
Same as "-240"
Same as "-241"
*CTL
System SP5xxx
[Capture Settings]
*CTL
0: Disable, 1: Enable
001 With this function disabled, the settings related to the capture feature cannot be initialized,
displayed, or selected.
002
Panel Setting
269
The following 6 SP modes set Sets the default format for stored documents sent to the document
management server via the MLB.
Enabled only when optional MLB (Media Link Board) is installed.
0: JFIF/JPEG, 1: TIFF/MMR,
081 Format for Copy Color
2: TIFF/MH, 3: TIFF/MR
This SP is not used in this model.
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
This SP is not used in this model.
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
0: JFIF/JPEG, 1: TIFF/MMR,
2: TIFF/MH, 3: TIFF/MR
[5 to 95 / 50 / 1 /step]
091 Sets the JPEG format default for documents sent to the document management server via
the MLB with JPEG selected as the format.
Enabled only when optional MLB (Media Link Board) is installed.
270
System SP5xxx
113 Secondary srv port number This is basically adjusted by the remote system.
114 Secondary srv URL path
[0 to 3 / 2 / 1/step]
121 Selects the resolution for color copy mode. This is basically adjusted by the remote system.
0: 600dpi/ 1: 300dpi/ 2: 150dpi/ 3: 75dpi
Reso: Copy (Mono)
[0 to 5 / 3 / 1/step]
122 Selects the resolution for BW copy mode. This is basically adjusted by the remote system.
0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi
Reso: Print (Color)
123
Selects the resolution for color print mode. This is basically adjusted by the remote system.
0: 600dpi/ 1: 300dpi/ 2: 150dpi/ 3: 75dpi
Reso: Print (Mono)
124
Selects the resolution for BW print mode. This is basically adjusted by the remote system.
0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi
271
125
Selects the resolution for color fax mode. This is basically adjusted by the remote system.
0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi/ 6: 75dpi
126
Selects the resolution for BW fax mode. This is basically adjusted by the remote system.
0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi/ 6: 75dpi
Selects the resolution for color scanning mode. This is basically adjusted by the remote
system.
0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi/ 6: 75dpi
Selects the resolution for BW scanning mode. This is basically adjusted by the remote
system.
0: 600dpi/ 1: 400dpi/ 2: 300dpi/ 3: 200dpi/ 4: 150dpi/ 5: 100dpi/ 6: 75dpi
141
[0 or 1 / 1 / -]
0: Off, 1: On
Turns on or off the all address information transmission for the captured resources.
Stand-by Doc Max Number
142 Selects the maximum number of captured documents to be transmitted to the document
server.
5840
272
[IEEE 802.11]
System SP5xxx
[1 to 11 or 13 / 11 or 13 / 1 /step]
Channel MAX
*CTL
Europe/Asia: 1 to 13
NA/ Asia: 1 to 11
Sets the maximum number of channels available for data transmission via the wireless LAN.
006 The number of channels available varies according to location. The default settings are set
for the maximum end of the range for each area. Adjust the upper 4 bits to set the maximum
number of channels. DFU
*CTL
Europe: 1 to 13
NA/ Asia: 1 to 11
Sets the minimum number of channels available for data transmission via the wireless LAN.
007 The number of channels available varies according to location. The default settings are set
for the minimum end of the range for each area. Adjust the lower 4 bits to set the minimum
number of channels. DFU
Do not change the setting.
[0 x 00 to 0 x FF / 0 x FF to Auto / -]
0 x FF to Auto [Default]
0 x 11 55M Fix
0 x 10 48M Fix
0 x 0F 36M Fix
0 x 0E 18M Fix
0 x 0D 12M Fix
008 Transmission Speed
*CTL
0 x 0B 9M Fix
0 x 0A 6M Fix
0 x 07 11M Fix
0 x 05 5.5M Fix
0 x 08 1M Fix
0 x 13 0 x FE (reserved)
0 x 12 72M (reserved)
0 x 09 22M (reserved)
273
*CTL
00: Key #1
01: Key #2 (Reserved)
10: Key #3 (Reserved)
11: Key #4 (Reserved)
Adjusts the fragment threshold for the
IEEE802.11 card.
3
042 Fragment Thresh
*CTL
*CTL
[0 to 1 / 1 / 1] 0: Off, 1: On
This SP is displayed only when the IEEE802.11
card is installed.
*CTL
*CTL
[1 to 3 / 3 / 1]
1: Info, 2: warning, 3: error
This SP is displayed only when the IEEE802.11
card is installed.
5841
274
System SP5xxx
*CTL
001 Setting 1
*CTL
002 Setting 2
*CTL
0: Date/Hour/Minute/Second
1: Minute/Second/Msec.
0 to 6: Not used
5844
[USB]
001
Transfer Rate
*CTL
*CTL
003 Product ID
*CTL
*CTL
275
*CTL
*CTL
100
Notify Unsupport
*CTL
[0 or 1 / 1 / -]
0: Disable, 1: Enable
5845
*CTL
Sets the FTP port number used when image files to the Scan Router Server.
IP Address (Primary)
002 Use this SP to set the Scan Router Server address. The IP address under the transfer tab
can be referenced by the initial system setting.
Delivery Error Display Time
006 Use this setting to determine the length of time the prompt message is displayed when a
test error occurs during document transfer with the NetFile application and an external
device.
IP Address (Secondary)
008 Specifies the IP address assigned to the computer designated to function as the secondary
delivery server of Scan Router. This SP allows only the setting of the IP address without
reference to the DNS setting.
Delivery Server Model
[0 to 4/ 0 / 1 /step]
Allows changing the model of the delivery server registered by the I/O device.
0: Unknown
009 1: SG1 Provided
2: SG1 Package
3: SG2 Provided
4: SG2 Package
276
System SP5xxx
[0 to 255 / 0 / 1 /step]
Changes the capability of the registered that the I/O device registered.
Bit7 = 1 Comment information exits
Bit6 = 1 Direct specification of mail address possible
010
[0 to 255 / 0 / 1 /step]
Changes the capability of the registered that the I/O device registered.
011
Bit7 = 1 Address book usage limitation (Limitation for each authorized user)
Bit6 = 1 RDH authorization link
Bit5 to 0: Not used
013
014
015
016
017
277
018
022
Enables or disables the prevention function for the continuous data sending error.
[0 to 1 / 0 / -]
0: Disable, 1: Enable
5846
[UCS Settings]
*CTL
Displays ID
001 Displays the unique device ID in use by the delivery server directory. The value is only
displayed and cannot be changed. This ID is created from the NIC MAC or IEEE 1394
EUI. The ID is displayed as either 6-byle or 8-byte binary.
Machine ID Clear (For Delivery Server)
Clears ID
002 Clears the unique ID of the device used as the name in the file transfer directory. Execute
this SP if the connection of the device to the delivery server is unstable. After clearing the
ID, the ID will be established again automatically by cycling the machine off and on.
Maximum Entries
003 Changes the maximum number of entries that UCS can handle.
If a value smaller than the present value is set, the UCS managed data is cleared, and the
data (excluding user code information) is displayed.
Delivery Server Retry Timer
[0 to 255 / 0 / 1 /step]
006 Sets the interval for retry attempts when the delivery server fails to acquire the delivery
server address book.
Delivery Server Retry Times
[0 to 255 / 0 / 1 /step]
007 Sets the number of retry attempts when the delivery server fails to acquire the delivery server
address book.
Delivery Server Maximum Entries
008 Sets the maximum number account entries of the delivery server user information managed
by UCS.
278
System SP5xxx
010
[1 to 255 / 60 / 1 /step]
Sets the length of the timeout for the search of the LDAP server.
Procedure
1. Turn the machine off.
2. Install a new HDD.
3. Turn the machine on.
4. The address book and its initial data are created on the HDD automatically.
5. However, at this point the address book can be accessed by only the system
administrator or key operator.
6. Enter the SP mode and do SP5846-041. After this SP executes successfully, any user
can access the address book.
Displays the slot number where an address book data
is in.
[0 to 30 / - /1]
0: Unconfirmed
1: SD Slot 1
2: SD Slot 2
4: USB Flash ROM
20: HDD
30: Nothing
279
Search Option
This SP uses bit switches to set up the fuzzy search options for the UCS local address book.
Bit: Meaning
060
280
System SP5xxx
Complexity Option 1
Use this SP to set the conditions for password entry to access the local address book.
Specifically, this SP limits the password entry to upper case and sets the length of the
password.
062 [0 to 32 / 0 / 1 /step]
This SP does not normally require adjustment.
This SP is enabled only after the system administrator has set up a group password
policy to control access to the address book.
SP5847-1 through SP5847-8 changes the default settings of image data transferred
externally by the Net File page reference function.
5847
[ 0 to 5 / 2 / 1 /step]
SP5847-21 sets the default for JPEG image quality of image files handled by NetFile.
"Net files" are jobs to be printed from the document server using a PC and the
DeskTopBinder software.
001 Rate for Copy Color
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
281
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
0: 1x
1: 1/2x
2: 1/3x
3: 1/4x
4: 1/6x
5: 1/8x
*CTL
SP5848-2 sets the 4-bit switch assignment for the access control setting. Setting of 0001
has no effect on access and delivery from Scan Router.
5848 100 sets the maximum size allowed for downloaded images. The default is equal
to 1 gigabyte.
Access Ctrl: Repository (only
002
Lower 4 bits)
282
System SP5xxx
003
004
007
099
DFU
Specifies the max size of the image data that the
machine can download.
[1 to 1024 / 1024 / 1 MB /step]
DFU
[Installation Date]
5849 1 Display
*CTL
283
[0 or 1 / 1 / - ]
0: OFF (No Print)
1: ON (Print)
5850
*CTL
Sets the operation mode for the Bluetooth Unit. Press either key.
[0:Public] [1: Private]
[Stamp Data Download]
5853
Use this SP to download the fixed stamp data stored in the firmware of the ROM and copy
it to the HDD. This SP can be executed as many times as required. This SP must be executed
after replacing or formatting the hard disks.
This SP can be executed only with the hard disks installed.
[Remote ROM Update]
5856
Allows the technician to upgrade the firmware using a local port (IEEE1284) when
updating the remote ROM.
[0 to 1 / 0 / 1/step]
002 Local Port
*CTL
0: Disable
1: Enable
5857
284
*CTL
System SP5xxx
0: OFF, 1: ON
001 Switches the debug log feature on and off. The debug log cannot be captured until this
feature is switched on.
Target (2: HDD 3: SD)
2: HDD, 3: SD Card
002 Selects the storage device to save debug logs information when the conditions set with
SP5-858 are satisfied.
[ 2 to 3 / 2 / 1 /step]
Save to HDD
005
006
Saves the debug log of the input SC number in memory to the HDD.
A unique file name is generated to avoid overwriting existing file names on the SD Card.
Up to 4MB can be copied to an SD Card. 4 MB segments can be copied one by one to
each SD Card.
Save to SD Card
Saves the debug log of the input SC number in memory to the SD card.
*CTL
These SPs select the content of the debugging information to be saved to the destination
selected by SP5857-002.
SP5858-3 stores one SC specified by number. Refer to Section 4 for a list of SC error codes.
285
[0 to 65535 / 0 / 1 /step]
Turns on/off the debug save for jam errors.
004 Jam
[0 or 1 / 0 / 1/ step]
0: OFF, 1: ON
5859
*CTL
001 Key 1
002 Key 2
003 Key 3
004 Key 4
005 Key 5
006 Key 6
007 Key 7
These SPs allow you to set up to 10 keys for log files for
functions that use common memory on the controller
board.
[9999999 to 9999999 / 0 / ]
008 Key 8
009 Key 9
010 Key 10
5860
[SMTP/POP3/IMAP4]
286
*CTL
[1 to 168 / 72 / ]
System SP5xxx
Sets the amount of time to wait before saving a mail that breaks up during reception. The
received mail is discarded if the remaining portion of the mail is not received during this
prescribed time.
021 MDN Response RFC2298 Compliance
[0 to 1 / 1 / ]
[0 to 1 / 0 / ]
Determines whether the FROM item of the mail header is switched to the validated account
after the SMTP server is validated.
0: No. "From" item not switched.
1: Yes. "From item switched.
025 SMTP Auth. Direct Setting
[0 or 1 / 0 / ]
[0 to 2 / 0 / 1]
0: Microsoft Outlook Express standard
1: Internet Draft standard
2: RFC standard
5866
287
*CTL
[0 or 1 / 0 / ]
0: Enable, 1: Disable
*CTL
5870
001 Writing
Initialize
*CTL
*CTL
5875
288
System SP5xxx
*CTL
*CTL
[0 or 1 / 0 / -]
0: Manual reboot, 1: Automatic reboot
5878
[Option Setup]
*ENG
5881
001 -
5884
*ENG
002 Tray 1
*ENG
003 Tray 2
*ENG
004 Tray 3
*ENG
005 Tray 4
*ENG
[0 or 1 / 1 / -]
0: Plain Paper 1
1: Plain Paper 2
289
5885
*CTL
*CTL
[0 to 2 / 0 / 1]
0: Thumbnail, 1: Icon, 2: Details
*CTL
Set Signature
*CTL
100
Selects whether the signature is added to the scanned documents with the WIM when they
are transmitted by an e-mail.
*CTL
290
*CTL
Not used
*CTL
Not used
System SP5xxx
5887
001 -
*CTL
001 -
*CTL
5893
001
SDK-1
002
SDK-2
003
SDK-3
004
SDK-4
005
SDK-5
006
SDK-6
5894
*CTL
001
5913
*ENG
[0 to 2 / 0 / 1/step]
*CTL
[3 to 30 / 3 / 1 second /step]
002 Sets the amount of time to elapse while the machine is in standby mode (and the operation
panel keys have not been used) before another application can gain control of the display.
5967
*CTL
0: ON, 1: OFF
Enables and disables the document server. This is a security measure that prevents image
001 data from being left in the temporary area of the HDD. After changing this setting, you must
switch the main switch off and on to enable the new setting.
5974
[Cherry Server]
Specifies which version of ScanRouter, "Lite" or "Full", is installed.
*CTL
[0 or 1 / 0 / ]
0: Lite, 1: Full
[Device Setting]
5985
292
The NIC and USB support features are built into the GW controller. Use this SP to enable
and disable these features. In order to use the NIC and USB functions built into the controller
board, these SP codes must be set to "1".
System SP5xxx
[0 to 2 / 0 / 1 /step]
0: Disable, 1: Enable, 2: Function limitation
When the "Function limitation" is set, "On board NIC" is
limited only for the NRS or LDAP/NT authentication.
001 On Board NIC
Other network applications than NRS or LDAP/NT
authentication are not available when this SP is set to
"2". Even though you can change the initial settings of
those network applications, the settings do not work.
002 On Board USB
5987
[0 or 1 / 0 / 1/step]
0: Disable, 1: Enable
5990
293
5997
006 Non-Default
022 Scanner SP
[0 or 1 / 1 / -]
0: Silent, 1: Fast
294
System SP6xxx
System SP6xxx
SP6-XXX (Peripherals)
6006
[ADF Adjustment]
Adjusts the side-to-side and leading registration of originals with the ARDF.
*ENG
Adjusts the amount of paper buckle to correct original skew for the front and rear sides.
005 Buckle: Duplex: 1st
006 Buckle: Duplex: 2nd
*ENG
*ENG
Displays the signals received from the sensors and switches of the ARDF. Only Bit 0 is used
for ADF input check ( p.377 "Input and Output Check Tables").
[ADF OUTPUT Check]
6008
6009
p.377 "Input
295
6010
001 -
*ENG
Specifies the original size for a size detected by the original sensor, since original sensors
cannot recognize all sizes.
[0 or 1 / 0 / - ]
*ENG
0: Setting 1
1: Setting 2
001 -
NA
EU/
ASIA
6017
Setting 1
Setting 2
DLT SEF
LG SEF
Foolscap SEF
LT SEF
LT LEF
US EXE LEF
DLT SEF
8K 267 x 390 mm
LT SEF
LT LEF
001 -
*CTL
001 -
296
ENG
[-2 to 2 / 0 / 0.2mm/step]
System SP6xxx
6102
6103
ENG
001 -
6104
ENG
ENG
Displays the signals received from sensors and switches of the finisher. (
Output Check Tables")
6830
Displays the signals received from sensors and switches of the finisher. (
Output Check Tables")
[Extra Staples]
Not used in this model
297
System SP7-xxx
SP7-XXX (Data Log)
7401
[Total SC Counter]
Displays the number of SC codes detected.
001 -
*CTL
[0 to 9999 / 0 / 1/step ]
[SC History]
7403
001 Latest
002 Latest 1
003 Latest 2
004 Latest 3
005 Latest 4
006 Latest 5
*CTL
007 Latest 6
008 Latest 7
009 Latest 8
010 Latest 9
[SC991 History]
7404
298
System SP7-xxx
001 Latest
002 Latest 1
003 Latest 2
004 Latest 3
005 Latest 4
*CTL
006 Latest 5
007 Latest 6
008 Latest 7
009 Latest 8
010 Latest 9
7502
001 -
7503
* CTL
[0 to 9999 / 0 / 1 sheet/step ]
001 -
*CTL
[0 to 9999 / 0 / 1 original/step ]
299
300
001 At Power On
*CTL
003 Tray 1: On
*CTL
004 Tray 2: On
*CTL
005 Tray 3: On
*CTL
006 Tray 4: On
*CTL
008 Bypass: On
*CTL
009 Duplex: On
*CTL
*CTL
*CTL
017 Registration: On
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
For details,
the "Jam Detection"
in the Main Chapters
System SP7-xxx
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
For details,
the "Jam Detection"
in the Main Chapters
301
7505
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
For details,
the "Jam Detection"
in the Main Chapters
001 At Power On
003 Registration Sensor: On
004 Registration Sensor: On
005 Original Exit Sensor: On
*CTL
7506
302
System SP7-xxx
005 A4 LEF
006 A5 LEF
014 B5 LEF
038 LT LEF
044 HLT LEF
132 A3 SEF
133 A4 SEF
134 A5 SEF
*CTL
[0 to 9999 / 0 / 1 sheet/step ]
141 B4 SEF
142 B5 SEF
160 DLT SEF
164 LG SEF
166 LT SEF
172 HLT SEF
255 Others
7507
303
001 Latest
002 Latest 1
003 Latest 2
004 Latest 3
005 Latest 4
006 Latest 5
*CTL
007 Latest 6
008 Latest 7
009 Latest 8
010 Latest 9
7508
7624
304
*CTL
System SP7-xxx
7801
001 PCU:Bk
*CTL
002 PCU:M
*CTL
003 PCU:C
*CTL
004 PCU:Y
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
0: No (Not PM maintenance)
7803
[0 or 1 / 1 / -]
*CTL
-001 to When a unit is replaced, the machine automatically detects that the new unit is installed.
-021 Then, the current PM counter value is automatically moved to the PM Counter - Previous
(SP7-906-1 to 21) and is reset to "0".
The total number of sheets printed with the last unit replaced can be checked with
SP7-906-1 to 21.
001 Paper
305
306
System SP7-xxx
Displays the number of revolutions of motors or clutches for each current maintenance unit.
[0 to 9999999 / 0 / 1 revolution/step ]
-031 to When a unit is replaced, the machine automatically detects that the new unit is installed.
-048 Then, the current PM counter value is automatically moved to the PM Counter - Previous
(SP7-906-31 to 48) and is reset to "0". The total number of revolutions made with the last
unit replaced can be checked with SP7-906-31 to 48.
031 Rotation: PCU: Bk
032 Rotation: PCU: C
307
(Current revolution Target revolution) 100. This shows how much of the units expected
-061 to lifetime has been used up.
-078
The Rotation% counter is based on rotations, not prints. If the number of rotations reaches
the limit, the machine enters the end condition for that unit. If the print count lifetime is
reached first, the machine also enters the end condition, even though the R% counter is still
less than 100%.
061 Rotation (%): PCU: Bk
062 Rotation (%): PCU: C
063 Rotation (%): PCU: M
064 Rotation (%): PCU: Y
065 Rotation (%): Development Unit: Bk
066 Rotation (%): Development Unit: C
067 Rotation (%): Development Unit:M
068 Rotation (%): Development Unit: Y
069 Rotation (%): Developer: Bk
070 Rotation (%): Developer: C
071 Rotation (%): Developer: M
072 Rotation (%): Developer: Y
073 Rotation (%): ITB Unit
074 Rotation (%): ITB Cleaning Unit
075 Rotation (%): Fusing Unit
076 Rotation (%): Fusing Pad
077 Rotation (%): Fusing Belt
078 Rotation (%):PTR Unit
308
System SP7-xxx
-091 to
-108 The Page% counter is based on printouts, not revolutions. If the number of printouts reaches
the limit, the machine enters the end condition for that unit. If the revolution count lifetime is
reached first, the machine also enters the end condition, even though the Page% counter
is still less than 100%.
*ENG
[0 to 255 / - / 1 %/step]
309
*ENG
[0 to 255 / - / 1 %/step]
7804
310
System SP7-xxx
012 Developer: Bk
013 Developer: C
014 Developer: M
015 Developer: Y
016 Developer: All
017 ITB Unit
7807
001 -
*CTL
*CTL
*CTL
7826
7827
*CTL
311
7832
001 7835
*CTL
[ACC Counter]
--
7836
001 -
*CTL
7853
312
Counts the number of occurrences (0 to 65,535) when dust was detected on the scanning
glass of the ADF or resets the dust detection counter. Counting is done only if SP4-020-1
(ADF Scan Glass Dust Check) is switched on.
001 Dust Detection Counter
*CTL
*CTL
[Replacement Counter]
Displays the PM parts replacement number.
[0 to 65535 / - / 1 /step]
System SP7-xxx
001 PCU: Bk
*CTL
002 PCU: C
*CTL
003 PCU: M
*CTL
004 PCU: Y
*CTL
*CTL
*CTL
*CTL
*CTL
009 Developer: Bk
*CTL
010 Developer: C
*CTL
011 Developer: M
*CTL
012 Developer: Y
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
*CTL
3
[0 to 255 / - / 1 /step]
[0 to 255 / - / 1 /step]
313
[Coverage Range]
Sets the color coverage threshold.
Coverage rate = Coverage per page / A4 full coverage (dots) x 100
There are three coverage counters: Color 1, Color 2, and Color 3
5% (default) is adjustable with SP7855-001.
20% (default) is adjustable with SP7855-002.
7855
The setting value of -002 must be set larger than the value of -001.
The total numbers of printouts (BW printing plus color printing) for each coverage range
are displayed with the following SPs.
Color1 counter: SP8601-021
Color2 counter: SP8601-022
Color3 counter: SP8601-023
001 Coverage Range 1
*CTL
[1 to 200 / 5 /1]
*CTL
[1 to 200 / 20 /1]
[Assert Info]
7901
Records the location where a problem is detected in the program. The data stored in this
SP is used for problem analysis. DFU
001 File Name
002 Number of Lines
*CTL
003 Location
7906
-001 to Displays the number of sheets printed with the previous maintenance units.
-020 [0 to 9999999 / 0 / 1 page/step ]
001 Page: PCU: Bk
002 Page: PCU: C
003 Page: PCU: M
314
*ENG
System SP7-xxx
315
316
System SP7-xxx
317
7931
318
*ENG
*EGN
003 Brand ID
*EGN
004 Area ID
*EGN
005 Product ID
*EGN
006 Color ID
*EGN
007 Maintenance ID
*EGN
*EGN
*EGN
010 Date
*EGN
*EGN
*EGN
System SP7-xxx
7932
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
[Toner Bottle M]
Displays the toner bottle information for M.
001 Machine Serial ID
*ENG
*EGN
003 Brand ID
*EGN
004 Area ID
*EGN
005 Product ID
*EGN
006 Color ID
*EGN
007 Maintenance ID
*EGN
*EGN
*EGN
010 Date
*EGN
*EGN
*EGN
319
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
7933
320
[Toner Bottle C]
Displays the toner bottle information for C.
001 Machine Serial ID
*ENG
*EGN
003 Brand ID
*EGN
004 Area ID
*EGN
005 Product ID
*EGN
006 Color ID
*EGN
007 Maintenance ID
*EGN
*EGN
*EGN
010 Date
*EGN
*EGN
*EGN
System SP7-xxx
7934
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
[Toner Bottle Y]
Displays the toner bottle information for Y.
001 Machine Serial ID
*ENG
*EGN
003 Brand ID
*EGN
004 Area ID
*EGN
005 Product ID
*EGN
006 Color ID
*EGN
007 Maintenance ID
*EGN
*EGN
*EGN
010 Date
*EGN
321
7935
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*ENG
*ENG
*ENG
322
System SP7-xxx
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
323
*ENG
*ENG
*ENG
*ENG
*ENG
*ENG
324
System SP7-xxx
7938
*ENG
*ENG
*ENG
*ENG
*ENG
7950
325
*ENG
*EGN
*EGN
*EGN
*EGN
*EGN
013 PCU: Bk
*EGN
014 PCU: C
*EGN
015 PCU: M
*EGN
016 PCU: Y
*EGN
*EGN
*EGN
*EGN
*EGN
021 Developer:Bk
*EGN
022 Developer:C
*EGN
023 Developer:M
*EGN
024 Developer:Y
*EGN
326
*ENG
System SP7-xxx
7952
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
328
Amount:PCU T-Collect
Bottle
System SP7-xxx
*EGN
*EGN
*EGN
*EGN
*EGN
Day Threshold:
025
Development Unit: Bk
*EGN
026
Day Threshold:
Development Unit: C
*EGN
027
Day Threshold:
Development Unit: M
*EGN
028
Day Threshold:
Development Unit: Y
*EGN
029
*EGN
030
*EGN
031
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
*EGN
034
329
*EGN
[0 to 999999999 / 0 / 1 mm/step]
042
*EGN
043
*EGN
*EGN
*EGN
045
[0 to 999999999 / 0 / 1 mm/step]
*EGN
[0 to 999999999 / 0 / 1 mm/step]
*EGN
[0 to 999999 / 0 / 1 sheet/step]
*EGN
[0 to 999999 / 0 / 1 sheet/step]
330
System SP7-xxx
*EGN
[0 to 999999 / 0 / 1 sheet/step]
[1 to 30 / 15 / 1 day/step]
These threshold days are used for @Remote
alarms.
*CTL
[0 to 99999999 / - / 1 mm/step]
331
7954
332
*CTL
[0 to 99999999 / - / 1 mm/step]
System SP8-xxx
System SP8-xxx
SP8-xxx: Data Log2
Many of these counters are provided for features that are currently not available, such as sending color
faxes, and so on. However, here are some Group 8 codes that when used in combination with others, can
provide useful information.
SP Numbers
What They Do
What it means
T:
C:
Copy application.
F:
Fax application.
P:
Print application.
S:
Scan application.
333
L:
O:
Other applications
(external network
applications, for
example)
The Group 8 SP codes are limited to 17 characters, forced by the necessity of displaying them on the small
LCDs of printers and faxes that also use these SPs. Read over the list of abbreviations below and refer to it
again if you see the name of an SP that you do not understand.
Key for Abbreviations
Abbreviation
334
What it means
>
AddBook
Address Book
Apl
Application
B/W
Bk
Black
Cyan
ColCr
Color Create
ColMode
Color Mode
Comb
Combine
Comp
Compression
Deliv
Delivery
System SP8-xxx
Abbreviation
What it means
DesApl
Dev Counter
Dup, Duplex
Emul
Emulation
FC
Full Color
FIN
Full Bleed
No Margins
GenCopy
GPC
Get Print Counter. For jobs 10 pages or less, this counter does not count
up. For jobs larger than 10 pages, this counter counts up by the number
that is in excess of 10 (e.g., for an 11-page job, the counter counts up
11-10 =1)
IFax
Internet Fax
ImgEdt
Image Edit performed on the original with the copier GUI, e.g. border
removal, adding stamps, page numbers, etc.
Black (YMCK)
LS
LSize
Mag
Magnification
MC
NRS
Org
OrgJam
Original Jam
Palm 2
Print Job Manager/Desk Top Editor: A pair of utilities that allows print jobs
to be distributed evenly among the printers on the network, and allows files
to moved around, combined, and converted to different formats.
335
Abbreviation
What it means
PC
Personal Computer
PGS
Pages. A page is the total scanned surface of the original. Duplex pages
count as two pages, and A3 simplex count as two pages if the A3/DLT
counter SP is switched ON.
PJob
Print Jobs
Ppr
Paper
PrtJam
PrtPGS
Print Pages
Red (Toner Remaining). Applies to the wide format model A2 only. This
machine is under development and currently not available.
Rez
Resolution
SC
Scn
Scan
Sim, Simplex
S-to-Email
Scan-to-E-mail
SMC
SMC report printed with SP5990. All of the Group 8 counters are recorded
in the SMC report.
Svr
Server
TonEnd
Toner End
TonSave
Toner Save
TXJob
Send, Transmission
YMC
YMCK
All of the Group 8 SPs are reset with SP5 801 1 Memory All Clear.
336
System SP8-xxx
T:Total Jobs
*CTL
8 002
C:Total Jobs
*CTL
8 003
F:Total Jobs
*CTL
8 004
P:Total Jobs
*CTL
8 005
S:Total Jobs
*CTL
8 006
L:Total Jobs
*CTL
8 001
These SPs reveal the number of times an application is used, not the number of pages processed.
When an application is opened for image input or output, this counts as one job.
Interrupted jobs (paper jams, etc.) are counted, even though they do not finish.
Only jobs executed by the customer are counted. Jobs executed by the customer engineer using the
SP modes are not counted.
When using secure printing (when a password is required to start the print job), the job is counted at
the time when either "Delete Data" or "Specify Output" is specified.
A job is counted as a fax job when the job is stored for sending.
When a fax is received to fax memory, the F: counter increments but the L: counter does not (the
document server is not used).
A fax broadcast counts as one job for the F: counter (the fax destinations in the broadcast are not
counted separately).
A fax broadcast is counted only after all the faxes have been sent to their destinations. If one
transmission generates an error, then the broadcast will not be counted until the transmission has been
completed.
A printed fax report counts as one job for the F: counter.
The F: counter does not distinguish between fax sending or receiving.
When a copy job on the document server is printed, SP8022 also increments, and when a print job
stored on the document server is printed, SP8024 also increments.
When an original is both copied and stored on the document server, the C: and L: counters both
increment.
When a print job is stored on the document server, only the L: counter increments.
When the user presses the Document Server button to store the job on the document server, only the
L: counter increments.
When the user enters document server mode and prints data stored on the document server, only the
L: counter increments.
337
When an image received from Palm 2 is received and stored, the L: counter increments.
When the customer prints a report (user code list, for example), the O: counter increments. However,
for fax reports and reports executed from the fax application, the F: counter increments.
8 011
T:Jobs/LS
*CTL
8 012
C:Jobs/LS
*CTL
8 013
F:Jobs/LS
*CTL
8 014
P:Jobs/LS
*CTL
8 015
S:Jobs/LS
*CTL
8 016
L:Jobs/LS
*CTL
8 017
O:Jobs/LS
*CTL
When a scan job is sent to the document server, the S: counter increments. When you enter document
server mode and then scan an original, the L: counter increments.
When a print job is sent to the document server, the P: counter increments.
When a network application sends data to the document server, the O: counter increments.
When an image from Palm 2 is stored on the document server, the O: counter increments.
When a fax is sent to the document server, the F: counter increments.
8 021
T:Pjob/LS
*CTL
8 022
C:Pjob/LS
*CTL
8 023
F:Pjob/LS
*CTL
8 024
P:Pjob/LS
*CTL
8 025
S:Pjob/LS
*CTL
8 026
L:Pjob/LS
*CTL
8 027
O:Pjob/LS
*CTL
When a copy job stored on the document server is printed with another application, the C: counter
increments.
When an application like DeskTopBinder merges a copy job that was stored on the document server
with a print job that was stored on the document server, the C: and P: counters both increment.
When a job already on the document server is printed with another application, the L: counter
increments.
338
System SP8-xxx
When a scanner job stored on the document server is printed with another application, the S: counter
increments. If the original was scanned from within document server mode, then the L: counter
increments.
When images stored on the document server by a network application (including Palm 2), are printed
with another application, the O: counter increments.
When a copy job stored on the document server is printed with a network application (Web Image
Monitor, for example), the C: counter increments.
When a fax on the document server is printed, the F: counter increments.
8 031
T:Pjob/DesApl
*CTL
8 032
C:Pjob/DesApl
*CTL
8 033
F:Pjob/DesApl
*CTL
8 034
P:Pjob/DesApl
*CTL
8 035
S:Pjob/DesApl
*CTL
8 036
L:Pjob/DesApl
*CTL
8 037
O:Pjob/DesApl
*CTL
3
These SPs reveal what applications were used to
output documents from the document server.
[0 to 9999999/ 0 / 1]
The L: counter counts the number of jobs printed
from within the document server mode screen at the
operation panel.
When documents already stored on the document server are printed, the count for the application
that started the print job is incremented.
When the print job is started from a network application (Desk Top Binder, Web Image Monitor, etc.)
the L: counter increments.
8 041
T:TX Jobs/LS
*CTL
8 042
C:TX Jobs/LS
*CTL
8 043
F:TX Jobs/LS
*CTL
8 044
P:TX Jobs/LS
*CTL
[0 to 9999999/ 0 / 1]
8 045
S:TX Jobs/LS
*CTL
8 046
L:TX Jobs/LS
*CTL
8 047
O:TX Jobs/LS
*CTL
When a stored copy job is sent from the document server, the C: counter increments.
339
When images stored on the document server by a network application or Palm2 are sent as an email, the O: counter increments.
8 051
T:TX Jobs/DesApl
*CTL
8 052
C:TX Jobs/DesApl
*CTL
8 053
F:TX Jobs/DesApl
*CTL
8 054
P:TX Jobs/DesApl
*CTL
8 055
S:TX Jobs/DesApl
*CTL
8 056
L:TX Jobs/DesApl
*CTL
8 057
O:TX Jobs/DesApl
*CTL
If the send is started from Desk Top Binder or Web Image Monitor, for example, then the O: counter
increments.
8 061
T:FIN Jobs
*CTL
[0 to 9999999/ 0 / 1]
These SPs total finishing methods for copy jobs only. The finishing method is specified by
the application.
F:FIN Jobs
8 063
[0 to 9999999/ 0 / 1]
These SPs total the finishing methods. The finishing method is specified by the application.
C:FIN Jobs
8 062
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs total finishing methods for fax jobs only. The finishing method is specified by
the application.
Note: Finishing features for fax jobs are not available at this time.
P:FIN Jobs
8 064
[0 to 9999999/ 0 / 1]
These SPs total finishing methods for print jobs only. The finishing method is specified by
the application.
S:FIN Jobs
8 065
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs total finishing methods for scan jobs only. The finishing method is specified by
the application.
Note: Finishing features for scan jobs are not available at this time.
340
System SP8-xxx
L:FIN Jobs
8 066
[0 to 9999999/ 0 / 1]
These SPs total finishing methods for jobs output from within the document server mode
screen at the operation panel. The finishing method is specified from the print window
within document server mode.
O:FIN Jobs
8 067
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs total finishing methods for jobs executed by an external application, over the
network. The finishing method is specified by the application.
8 06x 1 Sort
Number of jobs started in Sort mode. When a stored copy job is set for
Sort and then stored on the document server, the L: counter increments.
(See SP8 066 1)
8 06x 2 Stack
8 06x 3 Staple
8 06x 4 Booklet
8 06x 5 Z-Fold
Number of jobs started In any mode other than the Booklet mode and set
for folding (Z-fold).
8 06x 6 Punch
Number of jobs started in Punch mode. When Punch is set for a print job,
the P: counter increments. (See SP8 064 6.)
8 06x 7 Other
T:Jobs/PGS
8 071
*CTL
[0 to 9999999/ 0 / 1]
These SPs count and calculate the number of copy jobs by size based on the number of
pages in the job.
F:Jobs/PGS
8 073
[0 to 9999999/ 0 / 1]
These SPs count the number of jobs broken down by the number of pages in the job,
regardless of which application was used.
C:Jobs/PGS
8 072
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs count and calculate the number of fax jobs by size based on the number of
pages in the job.
341
P:Jobs/PGS
8 074
*CTL
These SPs count and calculate the number of print jobs by size based on the number of
pages in the job.
S:Jobs/PGS
8 075
*CTL
[0 to 9999999/ 0 / 1]
These SPs count and calculate the number of jobs printed from within the document server
mode window at the operation panel, by the number of pages in the job.
O:Jobs/PGS
8 077
[0 to 9999999/ 0 / 1]
These SPs count and calculate the number of scan jobs by size based on the number of
pages in the job.
L:Jobs/PGS
8 076
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
These SPs count and calculate the number of "Other" application jobs (Web Image
Monitor, Palm 2, etc.) by size based on the number of pages in the job.
8 07x 1 1 Page
8 07x 8
21 to 50 Pages
8 07x 2 2 Pages
8 07x 9
51 to 100 Pages
8 07x 3 3 Pages
8 07x 10
8 07x 4 4 Pages
8 07x 11
8 07x 5 5 Pages
8 07x 12
8 07x 6 6 to 10 Pages
8 07x 13
8 07x 7 11 to 20 Pages
8 07x 14
1001 to Pages
For example: When a copy job stored on the document server is printed in document server mode,
the appropriate L: counter (SP8076 0xx) increments.
Printing a fax report counts as a job and increments the F: counter (SP 8073).
Interrupted jobs (paper jam, etc.) are counted, even though they do not finish.
If a job is paused and re-started, it counts as one job.
If the finisher runs out of staples during a print and staple job, then the job is counted at the time the
error occurs.
For copy jobs (SP 8072) and scan jobs (SP 8075), the total is calculated by multiplying the number
of sets of copies by the number of pages scanned. (One duplex page counts as 2.)
The first test print and subsequent test prints to adjust settings are added to the number of pages of the
copy job (SP 8072).
342
System SP8-xxx
When printing the first page of a job from within the document server screen, the page is counted.
T:FAX TX Jobs
8 111
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total number of jobs (color or black-and-white) sent by fax, either
directly or using a file stored on the document server, on a telephone line.
Note: Color fax sending is not available at this time.
F: FAX TX Jobs
8 113
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total number of jobs (color or black-and-white) sent by fax directly
on a telephone line.
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total number of jobs (color or black-and-white) sent, either directly
or using a file stored on the document server, as fax images using I-Fax.
Note: Color fax sending is not available at this time.
F: IFAX TX Jobs
8 123
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of jobs (color or black-and-white) sent (not stored on the
document server), as fax images using I-Fax.
Note: Color fax sending is not available at this time.
8 12x 1 B/W
8 12x 2 Color
These counters count jobs, not pages.
343
The counters for color are provided for future use; the color fax feature is not available at this time.
The fax job is counted when the job is scanned for sending, not when the job is sent.
T:S-to-Email Jobs
8 131
8 135
[0 to 9999999/ 0 / 1]
These SPs count the total number of jobs (color or black-and-white) scanned and attached
to an e-mail, regardless of whether the document server was used or not.
S: S-to-Email Jobs
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of jobs (color or black-and-white) scanned and attached to
e-mail, without storing the original on the document server.
8 13x 1 B/W
8 13x 2 Color
8 13x 3 ACS
These counters count jobs, not pages.
If the job is stored on the document server, after the job is stored it is determined to be color or blackand-white then counted.
If the job is cancelled during scanning, or if the job is cancelled while the document is waiting to be
sent, the job is not counted.
If the job is cancelled during sending, it may or may not be counted, depending on what stage of the
process had been reached when the job was cancelled.
If several jobs are combined for sending to the Scan Router, Scan-to-Email, or Scan-to-PC, or if one
job is sent to more than one destination. each send is counted separately. For example, if the same
document is sent by Scan-to-Email as well as Scan-to-PC, then it is counted twice (once for Scan-toEmail and once for Scan-to-PC).
T:Deliv Jobs/Svr
8 141
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of jobs (color or black-and-white) scanned in scanner mode
and sent to a Scan Router server.
8 14x 1 B/W
8 14x 2 Color
344
[0 to 9999999/ 0 / 1]
These SPs count the total number of jobs (color or black-and-white) scanned and sent to
a Scan Router server.
S: Deliv Jobs/Svr
8 145
*CTL
System SP8-xxx
8 14x 3 ACS
These counters count jobs, not pages.
The jobs are counted even though the arrival and reception of the jobs at the Scan Router server
cannot be confirmed.
If even one color image is mixed with black-and-white images, then the job is counted as a "Color"
job.
If the job is cancelled during scanning, or if the job is cancelled while the document is waiting to be
delivered, the job is not counted.
If the job is cancelled during sending, it may or may not be counted, depending on what stage of the
process had been reached when the job was cancelled.
Even if several files are combined for sending, the transmission counts as one job.
T:Deliv Jobs/PC
8 151
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total number of jobs (color or black-and-white) scanned and sent to
a folder on a PC (Scan-to-PC).
Note: At the present time, 8 151 and 8 155 perform identical counts.
S:Deliv Jobs/PC
8 155
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total number of jobs (color or black-and-white) scanned and sent
with Scan-to-PC.
8 15x 1 B/W
8 15x 2 Color
8 15x 3 ACS
These counters count jobs, not pages.
If the job is cancelled during scanning, it is not counted.
If the job is cancelled while it is waiting to be sent, the job is not counted.
If the job is cancelled during sending, it may or may not be counted, depending on what stage of the
process had been reached when the job was cancelled.
Even if several files are combined for sending, the transmission counts as one job.
345
8 161
T:PCFAX TX Jobs
*CTL
8 163
F:PCFAX TX Jobs
*CTL
[0 to 9999999/ 0 / 1]
Note: At the present time, these counters perform
identical counts.
This counts fax jobs started from a PC using a PC fax application, and sending the data out to the
destination from the PC through the copier.
8 171
T: Deliv Jobs/WSD
*CTL
8 175
S: Dvliv Jobs/WSD
*CTL
[0 to 9999999/ 0 / 1]
x 1 B/W
x 2 Color
x 3 ACS
8 181
*CTL
8 185
*CTL
[0 to 9999999/ 0 / 1]
x 1 B/W
x 2 Color
x 3 ACS
8 191
*CTL
8 192
*CTL
8 193
*CTL
8 195
*CTL
8 196
SP 8 191 to 8 196 count the number of scanned sides of pages, not the number of physical pages.
These counters do not count reading user stamp data, or reading color charts to adjust color.
Previews done with a scanner driver are not counted.
346
System SP8-xxx
A count is done only after all images of a job have been scanned.
Scans made in SP mode are not counted.
Examples
If 3 B5 pages and 1 A3 page are scanned with the scanner application but not stored, the S: count
is 4.
If both sides of 3 A4 sheets are copied and stored to the document server using the Store File button
in the Copy mode window, the C: count is 6 and the L: count is 6.
If both sides of 3 A4 sheets are copied but not stored, the C: count is 6.
If you enter document server mode then scan 6 pages, the L: count is 6.
T:LSize Scan PGS
8 201
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total number of large pages input with the scanner for scan and copy
jobs. Large size paper (A3/DLT) scanned for fax transmission are not counted.
Note: These counters are displayed in the SMC Report, and in the User Tools display.
F: LSize Scan PGS
8 203
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total number of large pages input with the scanner for fax transmission.
Note: These counters are displayed in the SMC Report, and in the User Tools display.
S:LSize Scan PGS
8 205
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total number of large pages input with the scanner for scan jobs only.
Large size paper (A3/DLT) scanned for fax transmission are not counted.
Note: These counters are displayed in the SMC Report, and in the User Tools display.
8 211
T:Scan PGS/LS
*CTL
8 212
C:Scan PGS/LS
*CTL
8 213
F:Scan PGS/LS
*CTL
8 215
S:Scan PGS/LS
*CTL
8 216
L:Scan PGS/LS
*CTL
347
If both sides of 3 A4 sheets are copied and stored to the document server, the C: count is 6 and the
L: count is 6.
If you enter document server mode then scan 6 pages, the L: count is 6.
ADF Org Feeds
8 221
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages fed through the ADF for front and back side
scanning.
Number of front sides fed for scanning:
3
8 221 1
Front
With an ADF that can scan both sides simultaneously, the Front side count is
the same as the number of pages fed for either simplex or duplex scanning.
With an ADF that cannot scan both sides simultaneously, the Front side count
is the same as the number of pages fed for duplex front side scanning. (The
front side is determined by which side the user loads face up.)
Number of rear sides fed for scanning:
8 221 2
Back
With an ADF that can scan both sides simultaneously, the Back count is the
same as the number of pages fed for duplex scanning.
With an ADF that cannot scan both sides simultaneously, the Back count is
the same as the number of pages fed for duplex rear-side scanning.
When 1 sheet is fed for duplex scanning the Front count is 1 and the Back count is 1.
If a jam occurs during the job, recovery processing is not counted to avoid double counting. Also, the
pages are not counted if the jam occurs before the first sheet is output.
Scan PGS/Mode
8 231
348
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages scanned by each ADF mode to determine the work
load on the ADF.
8 231 2 SADF
8 231 5 Platen
System SP8-xxx
If the scan mode is changed during the job, for example, if the user switches from ADF to Platen mode,
the count is done for the last selected mode.
The user cannot select mixed sizes or non-standard sizes with the fax application so if the originals
page sizes are mixed or non-standard, these are not counted.
If the user selects "Mixed Sizes" for copying in the platen mode, the Mixed Size count is enabled.
In the SADF mode if the user copies 1 page in platen mode and then copies 2 pages with SADF, the
Platen count is 1 and the SADF count is 3.
T:Scan PGS/Org
8 241
8 242
8 243
8 245
*CTL
These SPs count the total number of scanned pages by original type for all jobs, regardless
of which application was used.
C:Scan PGS/Org
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages scanned by original type for Copy jobs.
F:Scan PGS/Org
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages scanned by original type for Fax jobs.
S:Scan PGS/Org
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages scanned by original type for Scan jobs.
L:Scan PGS/Org
8 246
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages scanned and stored from within the document server
mode screen at the operation panel, and with the Store File button from within the Copy
mode screen
8 241
8 242
8 243
8 245
8 246
8 24x 1: Text
Yes
Yes
Yes
Yes
Yes
8 24x 2: Text/Photo
Yes
Yes
Yes
Yes
Yes
8 24x 3: Photo
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
8 24x 5: Map
Yes
Yes
No
Yes
8 24x 6: Normal/Detail
Yes
No
Yes
No
No
Yes
No
Yes
No
No
8 24x 8: Binary
Yes
No
No
Yes
No
349
8 24x 9: Grayscale
Yes
No
No
Yes
No
Yes
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
If the scan mode is changed during the job, for example, if the user switches from ADF to Platen mode,
the count is done for the last selected mode.
8 251
T:Scan PGS/ImgEdt
*CTL
8 252
C:Scan PGS/ImgEdt
*CTL
8 255
S:Scan PGS/ImgEdt
*CTL
8 256
L:Scan PGS/ImgEdt
*CTL
8 257
O:Scan PGS/ImgEdt
*CTL
Positive/Negative
[0 to 9999999/ 0 / 1]
Note: The count totals the number of times the edit
features have been used. A detailed breakdown of
exactly which features have been used is not given.
The L: counter counts the number of pages stored from within the document server mode screen at the
operation panel, and with the Store File button from within the Copy mode screen.
8 261
T:Scan PGS/ColCr
*CTL
8 262
*CTL
8 266
L:Scn PGS/ColCr
*CTL
350
System SP8-xxx
8 281
T:Scn PGS/TWAIN
*CTL
8 285
S:Scn PGS/TWAIN
*CTL
[0 to 9999999/ 0 / 1]
Note: At the present time, these counters perform
identical counts.
8 291
T:Scan PGS/Stamp
*CTL
8 293
F:Scan PGS/Stamp
*CTL
8 295
S:Scan PGS/Stamp
*CTL
T:Scan PGS/Size
8 301
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by size the total number of pages scanned by the Scan application. Use
these totals to compare original page size (scanning) and output page size [SP 8-445].
L:Scan PGS/Size
8 306
*CTL
These SPs count by size the total number of pages scanned by the Fax application. Use
these totals to compare original page size (scanning) and output page size [SP 8-443].
S:Scan PGS/Size
8 305
[0 to 9999999/ 0 / 1]
These SPs count by size the total number of pages scanned by the Copy application. Use
these totals to compare original page size (scanning) and output (printing) page size [SP
8-442].
F:Scan PGS/Size
8 303
*CTL
These SPs count by size the total number of pages scanned by all applications. Use these
totals to compare original page size (scanning) and output (printing) page size [SP 8-441].
C:Scan PGS/Size
8 302
[0 to 9999999/ 0 / 1]
The L: counter counts the number of pages stored from
within the document server mode screen at the
operation panel, and with the Store File button from
within the Copy mode screen
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by size the total number of pages scanned and stored from within the
document server mode screen at the operation panel, and with the Store File button from
within the Copy mode screen. Use these totals to compare original page size (scanning)
and output page size [SP 8-446].
351
8 30x 1 A3
8 30x 2 A4
8 30x 3 A5
8 30x 4 B4
8 30x 5 B5
8 30x 6 DLT
8 30x 7 LG
8 30x 8 LT
8 30x 9 HLT
8 30x 10 Full Bleed
8 30x
Other (Standard)
254
8 30x
Other (Custom)
255
T:Scan PGS/Rez
8 311
[0 to 9999999/ 0 / 1]
These SPs count by resolution setting the total number of pages scanned by applications
that can specify resolution settings.
S: Scan PGS/Rez
8 315
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by resolution setting the total number of pages scanned by applications
that can specify resolution settings.
Note: At the present time, SP8-311 and SP8-315 perform identical counts.
System SP8-xxx
The Fax application does not allow finely-adjusted resolution settings so no count is done for the Fax
application.
8 381
T:Total PrtPGS
*CTL
8 382
C:Total PrtPGS
*CTL
8 383
F:Total PrtPGS
*CTL
8 384
P:Total PrtPGS
*CTL
8 385
S:Total PrtPGS
*CTL
8 386
L:Total PrtPGS
*CTL
8 387
O:Total PrtPGS
*CTL
When the A3/DLT double count function is switched on with SP5104, 1 A3/DLT page is counted as
2.
When several documents are merged for a print job, the number of pages stored are counted for the
application that stored them.
These counters are used primarily to calculate charges on use of the machine, so the following pages
are not counted as printed pages:
- Blank pages in a duplex printing job.
- Blank pages inserted as document covers, chapter title sheets, and slip sheets.
- Reports printed to confirm counts.
- All reports done in the service mode (service summaries, engine maintenance reports, etc.)
- Test prints for machine image adjustment.
- Error notification reports.
- Partially printed pages as the result of a copier jam.
LSize PrtPGS
8 391
*CTL
[0 to 9999999/ 0 / 1]
These SPs count pages printed on paper sizes A3/DLT and larger.
Note: In addition to being displayed in the SMC Report, these counters are also displayed
in the User Tools display on the copy machine.
353
8 401
T:PrtPGS/LS
*CTL
8 402
C:PrtPGS/LS
*CTL
8 403
F:PrtPGS/LS
*CTL
8 404
P:PrtPGS/LS
*CTL
8 405
S:PrtPGS/LS
*CTL
8 406
L:PrtPGS/LS
*CTL
Print jobs done with Web Image Monitor and Desk Top Binder are added to the L: count.
Fax jobs done with Web Image Monitor and Desk Top Binder are added to the F: count.
8 411
Prints/Duplex
*CTL
T:PrtPGS/Dup Comb
8 421
354
*CTL
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by binding and combine, and n-Up settings the number of pages
processed for printing by the printer application.
S:PrtPGS/Dup Comb
8 425
[0 to 9999999/ 0 / 1]
These SPs count by binding and combine, and n-Up settings the number of pages
processed for printing by the fax application.
P:PrtPGS/Dup Comb
8 424
*CTL
These SPs count by binding and combine, and n-Up settings the number of pages
processed for printing by the copier application.
F:PrtPGS/Dup Comb
8 423
[0 to 9999999/ 0 / 1]
These SPs count by binding and combine, and n-Up settings the number of pages
processed for printing. This is the total for all applications.
C:PrtPGS/Dup Comb
8 422
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by binding and combine, and n-Up settings the number of pages
processed for printing by the scanner application.
System SP8-xxx
L:PrtPGS/Dup Comb
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by binding and combine, and n-Up settings the number of pages
processed for printing from within the document server mode window at the operation
panel.
8 426
O:PrtPGS/Dup Comb
8 427
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by binding and combine, and n-Up settings the number of pages
processed for printing by Other applications
8 42x 7 4>
8 42x 9 8>
8 42x 12 Booklet
8 42x 13 Magazine
These counts (SP8 421 to SP8 427) are especially useful for customers who need to improve their
compliance with ISO standards for the reduction of paper consumption.
Pages that are only partially printed with the n-Up functions are counted as 1 page.
Here is a summary of how the counters work for Booklet and Magazine modes:
Magazine
Booklet
Original Pages
Count
Original Pages
Count
355
T:PrtPGS/ImgEdt
8 431
8 441
356
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total number of pages output with the three features below with
Other applications.
8 43x 1 Cover/Slip Sheet
8 43x 2 Series/Book
T:PrtPGS/Ppr Size
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by print paper size the number of pages printed by all applications.
C:PrtPGS/Ppr Size
8 442
*CTL
These SPs count the total number of pages output from within the document server mode
window at the operation panel with the three features below.
O:PrtPGS/ImgEdt
8 437
[0 to 9999999/ 0 / 1]
These SPs count the total number of pages output with the three features below with the
print application.
L:PrtPGS/ImgEdt
8 436
*CTL
These SPs count the total number of pages output with the three features below with the
copy application.
P:PrtPGS/ImgEdt
8 434
[0 to 9999999/ 0 / 1]
These SPs count the total number of pages output with the three features below,
regardless of which application was used.
C:PrtPGS/ImgEdt
8 432
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by print paper size the number of pages printed by the copy
application.
System SP8-xxx
8 443
F:PrtPGS/Ppr Size
8 447
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by print paper size the number of pages printed by the scanner
application.
L:PrtPGS/Ppr Size
8 446
*CTL
These SPs count by print paper size the number of pages printed by the printer
application.
S:PrtPGS/Ppr Size
8 445
[0 to 9999999/ 0 / 1]
These SPs count by print paper size the number of pages printed by the fax application.
P:PrtPGS/Ppr Size
8 444
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by print paper size the number of pages printed from within the
document server mode window at the operation panel.
O:PrtPGS/Ppr Size
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by print paper size the number of pages printed by Other applications.
8 44x 1 A3
8 44x 2 A4
8 44x 3 A5
8 44x 4 B4
8 44x 5 B5
8 44x 6 DLT
8 44x 7 LG
8 44x 8 LT
8 44x 9 HLT
357
8 451
PrtPGS/Ppr Tray
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of sheets fed from each paper feed station.
8 451 1 Bypass
Bypass Tray
8 451 2 Tray 1
Copier
8 451 3 Tray 2
Copier
8 451 4 Tray 3
8 451 5 Tray 4
8 451 6 Tray 5
LCT (Option)
8 451 7 Tray 6
8 451 8 Tray 7
8 451 9 Tray 8
8 451 10 Tray 9
8 451 11 Tray 10
8 451 12 Tray 11
8 451 13 Tray 12
8 451 14 Tray 13
8 451 15 Tray 14
8 451 16 Tray 15
T:PrtPGS/Ppr Type
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by paper type the number pages printed by all applications.
8 461
These counters are not the same as the PM counter. The PM counter is based on
feed timing to accurately measure the service life of the feed rollers. However,
these counts are based on output timing.
Blank sheets (covers, chapter covers, slip sheets) are also counted.
During duplex printing, pages printed on both sides count as 1, and a page printed
on one side counts as 1.
358
System SP8-xxx
8 462
8 463
8 464
C:PrtPGS/Ppr Type
[0 to 9999999/ 0 / 1]
These SPs count by paper type the number pages printed by the copy application.
F:PrtPGS/Ppr Type
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by paper type the number pages printed by the fax application.
P:PrtPGS/Ppr Type
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by paper type the number pages printed by the printer application.
L:PrtPGS/Ppr Type
8 466
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by paper type the number pages printed from within the document
server mode window at the operation panel.
8 46x 1 Normal
8 46x 2 Recycled
8 46x 3 Special
8 46x 4 Thick
8 46x 5 Normal (Back)
8 46x 6 Thick (Back)
8 46x 7 OHP
8 46x 8 Other
8 471
PrtPGS/Mag
*CTL
[0 to 9999999/ 0 / 1]
359
Counts are done for magnification adjusted for pages, not only on the operation panel but performed
remotely with an external network application capable of performing magnification adjustment as
well.
Magnification adjustments done with printer drivers with PC applications such as Excel are also
counted.
Magnification adjustments done for adjustments after they have been stored on the document server
are not counted.
T:PrtPGS/TonSave
*CTL
8 484
P:PrtPGS/TonSave
*CTL
These SPs count the number of pages printed with the Toner Save feature switched on.
Note: These SPs return the same results as this SP is limited to the Print application.
[0 to 9999999/ 0 / 1]
8 491
T:PrtPGS/Col Mode
*CTL
8 492
C:PrtPGS/Col Mode
*CTL
8 493
F:PrtPGS/Col Mode
*CTL
8 496
L:PrtPGS/Col Mode
*CTL
8 497
O:PrtPGS/Col Mode
*CTL
8 49x 1 B/W
8 49x 2 Single Color
8 49x 3 Two Color
8 49x 4 Full Color
360
8 501
T:PrtPGS/Col Mode
*CTL
8 504
P:PrtPGS/Col Mode
*CTL
8 057
O:PrtPGS/Col Mode
*CTL
System SP8-xxx
8 50x 1 B/W
8 50x 2 Mono Color
8 50x 3 Full Color
8 50x 4 Single Color
8 50x 5 Two Color
8 511
8 514
T:PrtPGS/Emul
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by printer emulation mode the total number of pages printed.
P:PrtPGS/Emul
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by printer emulation mode the total number of pages printed.
8 514 1
RPCS
8 514 2
RPDL
8 514 3
PS3
8 514 4
R98
8 514 5
R16
8 514 6
GL/GL2
8 514 7
R55
8 514 8
RTIFF
8 514 9
8 514 10
PCL5e/5c
8 514 11
PCL XL
8 514 12
IPDL-C
8 514 13
BM-Links
8 514 14
Other
8 514 15
IPDS
Japan Only
SP8 511 and SP8 514 return the same results as they are both limited to the Print application.
361
T:PrtPGS/FIN
*CTL
[0 to 9999999 / 0 / 1]
These SPs count by finishing mode the total number of pages printed by the Copy
application.
F:PrtPGS/FIN
8 523
[0 to 9999999 / 0 / 1]
These SPs count by finishing mode the total number of pages printed by all applications.
C:PrtPGS/FIN
8 522
*CTL
*CTL
[0 to 9999999 / 0 / 1]
These SPs count by finishing mode the total number of pages printed by the Fax
application.
NOTE: Print finishing options for received faxes are currently not available.
P:PrtPGS/FIN
8 524
8 52x 2 Stack
8 52x 3 Staple
8 52x 4 Booklet
8 52x 5 Z-Fold
8 52x 6 Punch
8 52x 7 Other
8 52x 8 Inside-Fold
362
[0 to 9999999 / 0 / 1]
*CTL
[0 to 9999999 / 0 / 1]
These SPs count by finishing mode the total number of pages printed from within the
document server mode window at the operation panel.
8 52x 1 Sort
8 52x 9
*CTL
These SPs count by finishing mode the total number of pages printed by the Scanner
application.
L:PrtPGS/FIN
8 526
[0 to 9999999 / 0 / 1]
These SPs count by finishing mode the total number of pages printed by the Print
application.
S:PrtPGS/FIN
8 525
*CTL
System SP8-xxx
8 52x 10
8 52x 11
8 52x 12
8 52x 13
8 52x 14
If stapling is selected for finishing and the stack is too large for stapling, the unstapled pages are still
counted.
The counts for staple finishing are based on output to the staple tray, so jam recoveries are counted.
8 531
Staples
T:Counter
8 581
*CTL
[0 to 9999999 / 0 / 1]
These SPs count the total output broken down by color output, regardless of the
application used. In addition to being displayed in the SMC Report, these counters are
also displayed in the User Tools display on the copy machine.
8 581 1 Total
8 581 2 Total: Full Color
8 581 3 B&W/Single Color
8 581 4 Development: CMY
8 581 5 Development: K
8 581 6 Copy: Color
8 581 7 Copy: B/W
8 581 8 Print: Color
8 581 9 Print: B/W
8 581 10 Total: Color
8 581 11 Total: B/W
363
C:Counter
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total output of the copy application broken down by color output.
8 582 1 B/W
8 582 2 Single Color
8 582 3 Two Color
8 582 4 Full Color
8 583
F:Counter
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total output of the fax application broken down by color output.
8 583 1 B/W
8 583 2 Single Color
8 584
P:Counter
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total output of the print application broken down by color output.
8 584 1 B/W
364
System SP8-xxx
L:Counter
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total output of the local storage broken down by color output.
8 582 1 B/W
8 582 2 Single Color
8 582 3 Two Color
8 582 4 Full Color
O:Counter
8 591
*CTL
These SPs count the totals for A3/DLT paper use, number of duplex pages printed, and
the number of staples used. These totals are for Other (O:) applications only.
8 591 1 A3/DLT
8 591 2 Duplex
Coverage Counter
8 601
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the total coverage for each color and the total printout pages for each
printing mode.
8 601 1 B/W
8 601 2 Color
8 601 11 B/W Printing Pages
8 601 12 Color Printing Pages
365
8 617
*CTL
[0 to 9999999/ 0 / 1]
8 617 1 SDK1
8 617 2 SDK2
8 617 3 SDK3
8 617 4 SDK4
These SPs count the total printout pages for each SDK
applicaion.
8 617 5 SDK5
8 617 6 SDK6
8 631
8 633
T:FAX TX PGS
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by color mode the number of pages sent by fax to a telephone number.
F:FAX TX PGS
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by color mode the number of pages sent by fax to a telephone number.
8 63x 1 B/W
8 63x 2 Color
If a document has color and black-and-white pages mixed, the pages are counted separately as B/
W or Color.
At the present time, this feature is provided for the Fax application only so SP8631 and SP8633 are
the same.
The counts include error pages.
If a document is sent to more than one destination with a Group transmission, the count is done for
each destination.
Polling transmissions are counted but polling RX are not.
Relay, memory, and confidential mailbox transmissions and are counted for each destination.
T:IFAX TX PGS
8 641
366
[0 to 9999999/ 0 / 1]
These SPs count by color mode the number of pages sent by fax to as fax images using
I-Fax.
F:IFAX TX PGS
8 643
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by color mode the number of pages sent by Fax as fax images using IFax.
System SP8-xxx
8 64x 1 B/W
8 64x 2 Color
If a document has color and black-and-white pages mixed, the pages are counted separately as B/
W or Color.
At the present time, this feature is provided for the Fax application only so SP8641 and SP8643 are
the same.
The counts include error pages.
If a document is sent to more than one destination with a Group transmission, the count is done for
each destination.
[0 to 9999999/ 0 / 1]
These SPs count by color mode the total number of pages attached to an e-mail for both
the Scan and document server applications.
S-to-Email PGS
8 655
*CTL
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by color mode the total number of pages attached to an e-mail for the
Scan application only.
8 65x 1 B/W
8 65x 2 Color
The count for B/W and Color pages is done after the document is stored on the HDD. If the job is
cancelled before it is stored, the pages are not counted.
If Scan-to-Email is used to send a 10-page document to 5 addresses, the count is 10 (the pages are
sent to the same SMTP server together).
If Scan-to-PC is used to send a 10-page document to 5 folders, the count is 50 (the document is sent
to each destination of the SMB/FTP server).
Due to restrictions on some devices, if Scan-to-Email is used to send a 10-page document to a large
number of destinations, the count may be divided and counted separately. For example, if a 10-page
document is sent to 200 addresses, the count is 10 for the first 100 destinations and the count is also
10 for the second 100 destinations, for a total of 20.).
367
T:Deliv PGS/Svr
8 661
*CTL
These SPs count by color mode the total number of pages sent to a Scan Router server
by both Scan and LS applications.
S:Deliv PGS/Svr
8 665
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by color mode the total number of pages sent to a Scan Router server
by the Scan application.
8 66x 1 B/W
8 66x 2 Color
The B/W and Color counts are done after the document is stored on the HDD of the Scan Router
server.
If the job is canceled before storage on the Scan Router server finishes, the counts are not done.
The count is executed even if regardless of confirmation of the arrival at the Scan Router server.
T:Deliv PGS/PC
8 671
*CTL
These SPs count by color mode the total number of pages sent to a folder on a PC (Scanto-PC) with the Scan and LS applications.
S:Deliv PGS/PC
8 675
[0 to 9999999/ 0 / 1]
*CTL
[0 to 9999999/ 0 / 1]
These SPs count by color mode the total number of pages sent with Scan-to-PC with the
Scan application.
8 67x 1 B/W
8 67x 2 Color
8 681
T:PCFAX TXPGS
*CTL
8 683
F:PCFAX TXPGS
*CTL
This counts pages sent from a PC using a PC fax application, from the PC through the copier to the
destination.
368
System SP8-xxx
When sending the same message to more than one place using broadcasting, the pages are only
counted once. (For example, a 10-page fax is sent to location A and location B. The counter goes
up by 10, not 20.)
8 691
T:TX PGS/LS
*CTL
8 692
C:TX PGS/LS
*CTL
8 693
F:TX PGS/LS
*CTL
8 694
P:TX PGS/LS
*CTL
8 695
S:TX PGS/LS
*CTL
8 696
L:TX PGS/LS
*CTL
Print jobs done with Web Image Monitor and Desk Top Binder are added to the count.
If several documents are merged for sending, the number of pages stored are counted for the
application that stored them.
When several documents are sent by a Fax broadcast, the F: count is done for the number of pages
sent to each destination.
TX PGS/Port
8 701
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages sent by the physical port used to send them. For
example, if a 3-page original is sent to 4 destinations via ISDN G4, the count for ISDN
(G3, G4) is 12.
8 701 1 PSTN-1
8 701 2 PSTN-2
8 701 3 PSTN-3
8 701 4 ISDN (G3,G4)
8 701 5 Network
8 711
8 715
T:Scan PGS/Comp
*CTL
[0 to 9999999/ 0 / 1]
S:Scan PGS/Comp
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages sent by each compression mode.
8 715 1 JPEG/JPEG2000
369
8 715 2 TIFF(Multi/Single)
8 715 3 PDF
8 715 4 Other
8 715 5 PDF/Comp
8 721
8 725
T: Deliv PGS/WSD
*CTL
S: Deliv PGS/WSD
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages scanned by each scanner mode.
x 1 B/W
x 2 Color
8 731
8 735
T: Scan PGS/Media
*CTL
S: Scan PGS/Media
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the number of pages scanned and saved in a meia by each scanner
mode.
x 1 B/W
x 2 Color
8 741
RX PGS/Port
[0 to 9999999/ 0 / 1]
These SPs count the number of pages received by the physical port used to receive them.
8 741 1 PSTN-1
8 741 2 PSTN-2
8 741 3 PSTN-3
8 741 4 ISDN (G3,G4)
8 741 5 Network
370
*CTL
System SP8-xxx
Dev Counter
8 771
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the frequency of use (number of rotations of the development rollers)
for black and other color toners.
8 771 1 Total
8 771 2 K
8 771 3 Y
8 771 4 M
8 771 5 C
Toner Bottle Info.
8 781
*CTL
[0 to 9999999/ 0 / 1]
8 781 1 Toner: BK
8 781 2 Toner: Y
8 781 3 Toner: M
8 781 4 Toner: C
8 791
LS Memory Remain
*CTL
Toner Remain
8 801
*CTL
[0 to 100/ 0 / 1]
These SPs display the percent of toner remaining for each color. This SP allows the user
to check the toner supply at any time.
Note: This precise method of measuring remaining toner supply (1% steps) is better
than other machines in the market that can only measure in increments of 10 (10%
steps).
8 801 1 K
8 801 2 Y
371
8 801 3 M
8 801 4 C
Cov Cnt: 0-10%
8 851
*CTL
[0 to 9999999/ 0 / 1]
These SPs display the number of scanned sheets on which the coverage of each color
is from 0% to 10%.
8 851 11 0 to 2%: BK
8 851 31 5 to 7%: BK
8 851 12 0 to 2%: Y
8 851 32 5 to 7%: Y
8 851 13 0 to 2%: M
8 851 33 5 to 7%: M
8 851 14 0 to 2%: C
8 851 34 5 to 7%: C
8 851 21 3 to 4%: BK
8 851 41 8 to 10%: BK
8 851 22 3 to 4%: Y
8 851 42 8 to 10%: Y
8 851 23 3 to 4%: M
8 851 43 8 to 10%: M
8 851 24 3 to 4%: C
8 851 44 8 to 10%: C
*CTL
[0 to 9999999/ 0 / 1]
These SPs display the number of scanned sheets on which the coverage of each color
is from 11% to 20%.
8 861 1 BK
8 861 2 Y
8 861 3 M
8 861 4 C
Cov Cnt: 21-30%
8 871
[0 to 9999999/ 0 / 1]
These SPs display the number of scanned sheets on which the coverage of each color
is from 21% to 30%.
8 871 1 BK
8 871 2 Y
372
*CTL
System SP8-xxx
8 871 3 M
8 871 4 C
Cov Cnt: 31%8 881
*CTL
[0 to 9999999/ 0 / 1]
These SPs display the number of scanned sheets on which the coverage of each color
is 31% or higher.
8 881 1 BK
8 881 2 Y
8 881 3 M
8 881 4 C
8 891
Page/Toner Bottle
*CTL
[0 to 9999999/ 0 / 1]
These SPs display the amount of the remaining current toner for each color.
8 891 1 BK
8 891 2 Y
8 891 3 M
8 891 4 C
8 901
Page/Toner Prev1
*CTL
[0 to 9999999/ 0 / 1]
These SPs display the amount of the remaining previous toner for each color.
8 901 1 BK
8 901 2 Y
8 901 3 M
8 901 4 C
8 911
Page/Toner Prev2
*CTL
[0 to 9999999/ 0 / 1]
These SPs display the amount of the remaining 2nd previous toner for each color.
8 911 1 BK
373
8 911 2 Y
8 911 3 M
8 911 4 C
8 921
*CTL
[0 to 9999999/ 0 / 1]
Displays the total coverage and total printout number for each color.
374
*CTL
[0 to 9999999/ 0 / 1]
These SPs count the amount of time the machine spends in each operation mode. These
SPs are useful for customers who need to investigate machine operation for
improvement in their compliance with ISO Standards.
System SP8-xxx
8 941 6 SC
8 941 7 PrtJam
8 941 8 OrgJam
8 951
AddBook Register
*CTL
These SPs count the number of events when the machine manages data registration.
8 951 4 Group
Group destination
registrations.
8 951 6 F-Code
Printer application
registrations with the Program
(job settings) feature.
Scanner application
registrations with the Program
(job settings) feature.
[0 to 9999999/ 0 / 1]
[0 to 255 / 0 / 255]
375
8 999
376
[0 to 9999999/ 0 / 1]
Displays the total coverage and total printout number for each color.
8 999 1 Total
*CTL
Result
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
Copier
5803
Description
Reading
0
Normal
Lock
Normal
Lock
Normal
Lock
Normal
Lock
Normal
Lock
Normal
Lock
Normal
Lock
Normal
Lock
Normal
Lock
Normal
Lock
Normal
Lock
Normal
Lock
New
Not new
Not detected
Detected
377
Paper detected
No paper detected
Actuator detected
Actuator detected
Paper detected
No paper detected
Paper detected
No paper detected
HP
Not HP
5803 23 HVPS:CB
5803 24 HVPS:T
Door close
Door open
Cover close
Cover open
Not set
Set
Not set
Set
Set
Not set
Set
Not set
End
Not end
End
Not end
End
Not end
End
Not end
Paper detected
No paper detected
Paper detected
No paper detected
Paper detected
No paper detected
5803 22
ID/MUSIC Sn Shutter HP Sn
(PTR Contact Sensor)
378
HP (Contact)
Set
Not HP
(not contact)
Not set
Set
Not set
Full
Not full
Paper detected
No paper detected
Paper detected
No paper detected
Detected
Not detect
HP
Not HP
Not end
End
Not end
End
Not end
End
Set
Not set
Set
Not set
5803 54 Interlock SW 1
Door close
Door open
5803 55 Interlock SW 2
Door close
Door open
5803 56 DIP SW
Not set
Set
Lock
Normal
Paper detected
No paper detected
Set
Not set
Paper detected
No paper detected
Paper detected
No paper detected
Set
Not set
Not HP
HP
379
Not set
Set
Upper limit
Open
Close
Not set
Set
Not end
End
Upper limit
Upper limit
Open
Close
5803 90 2T PFU:Upper PE Sn
Not end
End
5803 91 2T PFU:Lower PE Sn
Not end
End
5803 92 2T PFU:V-Transport Sn
Paper detected
No paper detected
Not HP
HP
Open
Close
380
Bit
Europe/Asia
A3 SEF*1
(A3 SEF)
B4 SEF *2
(B4 SEF)
A4 SEF
A4 SEF
B5 SEF
B5 SEF
A4 LEF*3
(A4 LEF)
B5 LEF*4
(B5 LEF)
A5 LEF
A5 LEF
*1: The machine detects either 11" x 17" SEF or A3 SEF, depending on the setting of SP 5-181-002
(Tray 1) or SP 5-181-006 (Tray 2).
*2: The machine detects either 8.5" x 14" SEF or B4 SEF, depending on the setting of SP 5-181-003
(Tray 1) or SP 5-181-007 (Tray 2).
*3: The machine detects either 11" x 81/2" LEF or A4 LEF, depending on the setting of SP 5-181-001
(Tray 1) or SP 5-181-005 (Tray 2).
*4: The machine detects either B5 LEF or 10.5" x 7.25" LEF, depending on the setting of SP 5-181-004
(Tray 1) or SP 5-181-008 (Tray 2).
Length Sensor
NA
EU/ASIA
HLT SEF
B6 SEF
HLT SEF
A5 SEF
HLT SEF
A5 SEF
LT/LG SEF*1
A4 SEF
bit3
Bit2
Bit1
Bit0
1
0
381
Length Sensor
NA
EU/ASIA
LT/LG SEF*1
A5 LEF
DLT SEF
A3 SEF
LT LEF
A4 LEF
bit3
Bit2
Bit1
Bit0
*1: The paper size (LT or LG) can be selected with SP1-007-001.
Width Sensor
Length Sensor
Metric version
Inch version
W1
W2
W3
L1
L2
SP4-301
display
A3
11" x 17"
00000011
B4
10" x 14"
00000011
F4
8.5" x 13", 8.25" x 13",
or 8" x 13"
8.5" x 14"
00000011
A4 LEF
8.5" x 11"
00000000
B5 LEF
00000000
A4 SEF
11" x 8.5"
00000010
B5 SEF
00000010
A5 LEF/ SEF
5.5" x 8.5",
8.5" x 5.5"
00000000
382
Models
Bit
North America
Europe/Asia
A3 SEF*1
(A3 SEF)
B4 SEF *2
(B4 SEF)
A4 SEF
A4 SEF
B5 SEF
B5 SEF
A4 LEF*3
(A4 LEF)
B5 LEF*4
(B5 LEF)
A5 LEF
A5 LEF
A5 SEF
A5 SEF
*1: The machine detects either 11" x 17" SEF or A3 SEF, depending on the setting of SP 5-181-010 (Tray
3) or SP 5-181-014 (Tray 4).
*2: The machine detects either 8.5" x 14" SEF or B4 SEF, depending on the setting of SP 5-181-011 (Tray
3) or SP 5-181-015 (Tray 4).
*3: The machine detects either 11" x 81/2" LEF or A4 LEF, depending on the setting of SP 5-181-009
(Tray 3) or SP 5-181-013 (Tray 4).
*4: The machine detects either B5 LEF or 10.5" x 7.25" LEF, depending on the setting of SP 5-181-012
(Tray 3) or SP 5-181-016 (Tray 4).
ARDF (D366)
6007
Description
Reading
0
Paper detected
383
Paper detected
Paper detected
Paper detected
Paper detected
Paper detected
Paper detected
Paper detected
Paper detected
Paper detected
6007 13 Registration Sn
Paper detected
6007 14 Exit Sn
Paper detected
HP
Not HP
6120
Description
Not HP
HP
Not HP
HP
Not HP
HP
Paper detected
Up
Down
Paper detected
Down
Up
Paper detected
384
Reading
HP
Not HP
HP
Not HP
Normal
Lock
Close
Open
HP
Not HP
HP
Not HP
Not HP
HP
Paper detected
Paper detected
Paper detected
Paper detected
Paper detected
Paper detected
Full
Not full
Upper
Not upper
Paper detected
Lower
Not lower
Not HP
HP
Not rear
Rear Position
No staple
Staple detected
No staple
Staple detected
Not set
Set
385
2/3
4 (EU)
4 (Scan.)
6120-013
6120-014
386
Display
Description
387
388
389
390
Description
Description
391
ARDF (D366)
6008
392
Display
Description
Stamp Solenoid
3. When you want to select the single color of Magenta, Yellow or Cyan for printing a test pattern, select
the color with SP2-109-005 (2: Magenta, 3: Yellow, 4: Cyan).
4. When you want to change the density of printing a test pattern, select the density with SP2-109-006
to -009 for each color.
If you select "0" with SP2-109-006 to -009, the color to be adjusted to "0" does not come up
on a test pattern.
5. When you are prompted to confirm your selection, touch "Yes" to select the test pattern for printing.
6. Touch "Copy Window" to open the copy window, then select the settings for the test print (paper size
etc.).
If you want to use black and white printing, touch "Black & White" on the LCD. If you want to
use color printing, touch "Full Colour" on the LCD.
7. Press the "Start" key to start the test print.
8. After checking the test pattern, touch "SP Mode" on the LCD to return to the SP mode display.
9. Reset all settings to the default values.
10. Touch "Exit" twice to exit SP mode.
No.
Pattern
No.
Pattern
None
11
12
13
14
Ttrimming Area
16
393
394
17
Band (Horizontal)
18
Band (Vertical)
19
20
21
10
23
Bit Switch
bit 0
DFU
bit 1
DFU
bit 2
DFU
bit 3
No I/O Timeout
0: Disable
1: Enable
Enable: The MFP I/O Timeout setting will have no effect. I/O Timeouts will never occur.
bit 4
0: Disable
1: Enable
Enable: Print jobs will be saved to an SD Card in the GW SD slot ( "Card Save
Function" in "System Maintenance" chapter of the Field Service Manual).
bit 5
DFU
bit 6
DFU
bit 7
0: Disable
1: Enable
Enable: The machine prints all RPCS and PCL jobs with a border on the edges of the
printable area.
1001
Bit Switch
395
bit 0
DFU
bit 1
DFU
bit 2
Shift Collate
Normal Collate
A collation type (shift or normal) will be applied to all jobs that do not already have a
Collate Type configured.
0: Enable
1: Disable
1001
396
bit 4
DFU
bit 5
DFU
bit 6
DFU
bit 7
DFU
Bit Switch
bit 0
DFU
bit 1
DFU
bit 2
0: Disable
1: Enable
Enable: Uses the same left margin as older HP models such as HP4000/HP8000.
In other words, the left margin defined in the job (usually "<ESC>*r0A") will be changed
to "<ESC>*r1A"
1001
bit 3
DFU
bit 4
DFU
bit 5
DFU
bit 6
DFU
bit 7
DFU
Bit Switch
DFU
bit 1
DFU
bit 2
DFU
bit 3
0: Disable
1: Enable
If enabled, the simplex pages of IPDS jobs will be printed on the front side because of
printing on the back side of the page. This might reduce printing speed.
1001
bit 4
DFU
bit 5
DFU
bit 6
DFU
bit 7
DFU
Bit Switch
397
Disable
Enable
If enabled, users will be able to configure a Collate Type, Staple Type, and Punch Type
from the operation panel. The available types will depend on the device and configured
options.
After enabling the function, the settings will appear under:
"User Tools > Printer Features > System"
bit 1
0: Disable
(Single
copy)
1: Enable
(Multiple copy)
If a paper size or type mismatch occurs during the printing of multiple copies, only a
single copy is output by default. Using this BitSw, the device can be configured to print
all copies even if a paper mismatch occurs.
bit 2
DFU
bit 3
[PS] PS Criteria
Pattern3
Pattern1
Disable
(100)
Enable (1000)
Enable: Changes the maximum number of jobs that can be stored on the HDD via Job
Type settings to 1000. The default is 100.
bit 5
Face-up output
Disable
Enable
Enable: All print jobs will be output face-up in the destination tray.
bit 6
0: Disable
1: Enable
If enabled, the image rotation will be performed as they were in the specifications of
older models for the binding of pages of mixed orientation jobs.
The old models are below:
- PCL: Pre-04A models
- PS/PDF/RPCS:Pre-05S models
398
bit 7
1001
1: Enable
(Duplex)
0: Disable
1: Enable
Bit Switch
0: Disable
Bit Switch
bit 1
to 7
If enabled, simplex pages (in mixed simplex/duplex PS/PCL5 jobs only) and the last
page of an odd paged duplex job (PS, PCL5, PCL6), are always routed through the
duplex unit. Not having to switch paper paths increases the print speed slightly.
-
bit 0
DFU
bit 1
DFU
bit 2
DFU
bit 3
Disable
Enable
1001
DFU
Bit Switch
Enable: BW jobs submitted without a user code will be printed even if usercode
authentication is enabled.
Color jobs will not be printed without a valid user code.
bit 4
DFU
bit 5
DFU
bit 6
DFU
bit 7
DFU
399
1001
Bit Switch
0
"Disabled
(Immediatel
y)"
1
"Enabled
(10 seconds)"
3
bit 1
DFU
bit 2
Job Cancel
Disabled
(Not
cancelled)
Enabled
(Cancelled)
If this bit switch, all jobs will be cancelled after a jam occurs.
Note: If this bitsw is enabled, printing under the following conditions might result in
problems:
- Job submission via USB or Parallel Port
- Spool printing (WIM >Configuration > Device Settings > System)
bit 3
0: Disable
1: Enable
This bitsw causes the device to revert to the behavior of previous generations. It only
takes effect if "Bypass Tray Setting Priority" = "Driver/Command".
Previous spec (bitsw=1): If a standard sized paper mismatch occurred in the bypass
tray, the MFP always prompted for SEF paper.
If this bitsw=0 (default) then in the event of a standard sized paper mismatch, the MFP
will always prompt for paper of the rotation (SEF/LEF) determined by the MFP bypass
tray paper setting or by the bypass tray sensor.
Bit 4
to 7
1003
1003 1
DFU
[Clear Setting]
Initialize Printer System
Initializes settings in the "System" menu of the user mode.
1004
1004 1
1005
1005 1
1006
[Print Summary]
Print Summary
Prints the service summary sheet (a summary of all the controller settings).
[Display Version]
Disp. Version
Displays the version of the controller firmware.
[Sample/Locked Print]
*CTL
0: Linked, 1: On
Enables and disables the document server. When you select "0," the document server is
1006 1 enabled or disabled in accordance with Copy Service Mode SP5-967. When you select
"1," the document server is enabled regardless of Copy Service Mode SP5-967.
[Data Recall]
1101
Recalls a set of gamma settings. This can be either a) the factory setting, b) the previous
setting, or c) the current setting.
1101 1 Factory
1101 2 Previous
1101 3 Current
*CTL
1101 4 ACC
1102
1102 1
1103
[Resolution Setting]
Selects the printing mode (resolution) for the printer gamma adjustment.
2400x600 Photo, 1800x600 Photo, 600 x 600 Photo, 2400x600 Text, 1800x600, Text,
600x600 Text
[Test Page]
Prints the test page to check the color balance before and after the gamma adjustment.
1104
[Gamma Adjustment]
Adjusts the printer gamma for the mode selected in the "Mode Selection" menu.
*CTL
[0 to 30 / 15 / 1/step ]
*CTL
[0 to 30 / 15 / 1/step ]
Stores the print gamma adjusted with the "Gamma Adj." menu item as the current setting.
Before the machine stores the new "current setting", it moves the data currently stored as the
"current setting" to the "previous setting" memory storage location.
1106
402
[Toner Limit]
Adjusts the maximum toner amount for image development.
*CTL
403
Scanner SP Mode
SP1-xxx (System and Others)
1001
[Scan Nv Version]
1001 5 -
3
1004
*CTL
[Compression Type]
Selects the compression type for binary picture processing.
*CTL
[1 to 3 / 1 / 1/step ]
1: MH, 2: MR, 3: MMR
[Erase margin]
1005
1009
*CTL
*CTL
[0 to 5 / 0 / 1 mm/step ]
[0 or 1 / 0 / - ]
0: enable, 1: disable
1010
[0 or 1 / 0 / - ]
0: Display, 1: No display
*CTL
[0 or 1 / 0 / - ]
404
Scanner SP Mode
1012
1012 1
1013
[UserInfo release]
*CTL
[0 or 1 / 1 / - ]
0: No, 1: Yes
*CTL
[0 or 1 / 0 / - ]
0: OFF, 1: ON
Selects the compression ratio for grayscale processing mode (JPEG) for the three settings that
can be selected at the operation panel.
[5 to 95 / 20 / 1 /step ]
[5 to 95 / 40 / 1 /step ]
*CTL
[5 to 95 / 65 / 1 /step ]
[5 to 95 / 80 / 1 /step ]
[5 to 95 / 95 / 1 /step ]
Selects the compression ratio for clearlight PDF for the two settings that can be selected at
the operation panel.
*CTL
[5 to 95 / 25 / 1 /step ]
[5 to 95 / 20 / 1 /step ]
405
406