Beruflich Dokumente
Kultur Dokumente
MASTERSPEC
08/04 (R 05/05)
PRODUCT MASTERSPEC LICENSED BY ARCOM TO PELLA CORPORATION
This PRODUCT MASTERSPEC section is licensed by ARCOM (January, 2005) for distribution by Pella
Corporation. Changes made to MASTERSPEC by Pella Corporation are indicated using underline/strikeout text.
Review and accept changes according to project requirements and specifier's practice. The underline and strikeout
portions of the text in this Section are the sole responsibility of Pella Corporation. They are not provided by,
endorsed by, or representative of the opinions of ARCOM or The American Institute of Architects. For more
information contact Pella Corporation, 102 Main Street, Pella, IA 50219. Phone (800) 847-3552 or 641-621-1000.
Fax (641) 621-6487. Website: www.pellacommercial.com. Email: commercial@pella.com.
SCHEDULE 2 - DEFINITIONS
AW: Architectural.
HC: Heavy Commercial.
C: Commercial.
LC: Light Commercial.
R: Residential.
Design pressure number in pounds force per square foot (pascals) used to determine the structural
test pressure and water test pressure.
WOOD WINDOWS
085200 - 1
Retain paragraph and subparagraphs below if Architect has either delegated design responsibility to Contractor or
wants to review structural data as another way to verify windows' compliance with performance requirements or
performance designation.
PRODUCT DATA SHEET 1 - Structural Performance: Provide wood windows capable of withstanding the
effects of the following loads based on testing units representative of those indicated for Project that pass
AAMA/WDMA 101/I.S.2/NAFS, Uniform Load Structural Test:
Model building codes require windows and other fenestration to be designed and installed, according to ASCE 7, to
withstand wind pressure loads for components and cladding. Revise subparagraph below if loads are developed
from wind-tunnel tests. Building heights and window locations should be shown on Drawings.
1.1
Design Wind Loads: Determine design wind loads applicable to Project from basic wind speed
indicated in miles per hour (meters per second) at 33 feet (10 m) above grade, according to
ASCE 7, Section 6.5, "Method 2-Analytical Procedure," based on mean roof heights above grade
indicated on Drawings.
Delete four subparagraphs below if information is indicated on Drawings. Other factors that adjust for building
height, shape, and other characteristics such as topographic factor, gust effect factor, and enclosure classifications
may need to be included. This information should enable contractors to require window manufacturers to determine
positive and negative design wind pressure loads.
A.
B.
C.
D.
WOOD WINDOWS
Basic Wind Speed: [85 mph (38 m/s)] [90 mph (40 m/s)] <Insert value>.
Importance Factor: [I] [II] [III] [IV].
Exposure Category: [A] [B] [C] [D].
<Insert factor.>
085200 - 2
Deflection: Design glass framing system to limit lateral deflections of glass edges to less than
1/175 of glass-edge length or 3/4 inch (19 mm), whichever is less, at design pressure based on
testing performed according to AAMA/WDMA 101/I.S.2/NAFS, Uniform Load Deflection Test or
structural computations.
Model building codes and ASCE 7 establish criteria for buildings in hurricane-prone locations. Authorities having
jurisdiction may accept other test methods and protocols. Verify requirements of authorities having jurisdiction.
PRODUCT DATA SHEET 2 - Windborne-Debris Resistance: Provide glazed windows capable of resisting
impact from windborne debris, based on the pass/fail criteria as determined from testing glazed windows
identical to those specified, according to [ASTM E 1886 and testing information in ASTM E 1996]
[or] [AAMA 506] <Insert test method> and requirements of authorities having jurisdiction.
SCHEDULE 4 - SUBMITTALS
PRODUCT DATA SHEET 0 - Product Data: Include construction details, material descriptions, fabrication
methods, dimensions of individual components and profiles, hardware, finishes, and operating
instructions for each type of wood window indicated.
PRODUCT DATA SHEET 1 - Shop Drawings:
Include plans, elevations, sections, details, hardware,
attachments to other work, operational clearances, installation details, and the following:
Wood windows typically do not have poured and debridged thermal breaks as found on aluminum windows. Wood
provides a natural thermal break.
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
With Pella's recommended approach to specifying performance requirements, the next subparagraph is not needed.
This type of information is typically included in the Product Test Reports specified in paragraph 1.4.G.
Retain first subparagraph below if windows are required to withstand specific design loads and Architect either has
delegated design responsibility to Contractor or wants to review structural data as another way to verify windows'
compliance with performance requirements or performance designation.
1.9
For installed products indicated to comply with design loads, include structural analysis data
prepared by or under the supervision of a qualified professional engineer detailing fabrication and
assembly of wood windows and used to determine the following:
A.
B.
WOOD WINDOWS
Structural test pressures and design pressures from basic wind speeds indicated.
Deflection limitations of glass framing systems.
085200 - 3
PRODUCT DATA SHEET 3 - Samples for Verification: For wood windows and components required, prepared
on Samples of size indicated below.
If subparagraph 3 (an operable window) is selected, the other line items can be deleted.
3.1
3.2
3.3
3.4
3.5
3.6
Main Framing Member: 12-inch- (300-mm-) long, full-size sections of window frame[ with
factory-applied color finish].
Window Corner Fabrication: 12--by-12-inch- (300--by-300-mm-) long, full-size window corner
including full-size sections of window frame with factory-applied color finish, weather stripping,
and glazing.
Operable Window: Full-size unit with factory-applied finish.
Hardware: Full-size units with factory-applied finish.
Weather Stripping: 12-inch- (300-mm-) long sections.
<Insert component>: <Insert description>.
PRODUCT DATA SHEET 4 - Product Schedule: For wood windows. Use same designations indicated on
Drawings.
PRODUCT DATA SHEET 5 - Qualification Data:
[and] [testing agency].
If the test report is for a size that is at least as large as the largest size in the project, then smaller sizes do not need
separate test reports.
PRODUCT DATA SHEET 6 - Product Test Reports:
Based on evaluation of comprehensive tests
performed[ within the last four years] by a qualified testing agency for each type, class, grade, and size
of wood window. The size shall be at least as large as the largest unit of each type in the project.Test
results based on use of downsized test units will not be accepted.
PRODUCT DATA SHEET 7 - Maintenance Data: For [operable window sash] [operating hardware]
[weather stripping] [and] finishes to include in maintenance manuals.
PRODUCT DATA SHEET 8 - Warranty: Special warranty specified in this Section.
SCHEDULE 5 - QUALITY ASSURANCE
PRODUCT DATA SHEET 0 - Installer Qualifications: An installer acceptable to wood window manufacturer or
supplier for installation of units required for this Project.
0.1
0.2
WOOD WINDOWS
085200 - 4
Do not modify intended aesthetic effects, as judged solely by Architect, except with Architect's
approval. If modifications are proposed, submit comprehensive explanatory data to Architect for
review.
PRODUCT DATA SHEET 5 - Fenestration Standard: Comply with AAMA/WDMA 101/I.S.2/NAFS, "North
American Fenestration Standard Voluntary Performance Specification for Windows, Skylights and Glass
Doors," for definitions and minimum standards of performance, materials, components, accessories, and
fabrication unless more stringent requirements are indicated.
if required Pella participates in the WDMA Hallmark-certification program.
5.1
PRODUCT DATA SHEET 6 - Glazing Publications: Comply with published recommendations of glass
manufacturers and with GANA's "Glazing Manual" unless more stringent requirements are indicated.
PRODUCT DATA SHEET 7 - Mockups: Build mockups to verify selections made under sample submittals and
to demonstrate aesthetic effects and set quality standards for materials and execution.
7.1
PRODUCT DATA SHEET 8 - Preinstallation Conference: Conduct conference at Project site to comply with
requirements in Division 01 Section "Project Management and Coordination."
PRODUCT DATA SHEET 9 - Preinstallation Conference: Conduct conference at Project site to comply with
requirements in Division 01 Section "Project Management and Coordination." Review methods and
procedures related to wood windows including, but not limited to, the following:
9.1
9.2
9.3
9.4
Review and finalize construction schedule and verify availability of materials, Installer's
personnel, equipment, and facilities needed to make progress and avoid delays.
Review, discuss, and coordinate the interrelationship of wood windows with other exterior wall
components. Include provisions for structural anchorage, glazing, flashing, weeping, sealants, and
protection of finishes.
Review and discuss the sequence of work required to construct a watertight and weathertight
exterior building envelope.
Inspect and discuss the condition of substrate and other preparatory work performed by other
trades.
WOOD WINDOWS
085200 - 5
Established Dimensions: Where field measurements cannot be made without delaying the Work,
establish opening dimensions and proceed with fabricating wood windows without field
measurements. Coordinate wall construction to ensure that actual opening dimensions correspond
to established dimensions.
SCHEDULE 7 - WARRANTY
PRODUCT DATA SHEET 0 - Special Warranty: Manufacturer's standard form in which manufacturer agrees to
repair or replace wood windows that fail in materials or workmanship within specified warranty period.
0.1
For wood windows, condensation resistance depends on the type of glass specified. In a cold climate it is difficult to
prevent condensation on clear insulating glass. Consequently, condensation resistance is not covered by Pella's
wood window warranty.
B.
Structural failures including excessive deflection, water leakage, or air infiltration, or
condensation.
C.
Faulty operation of movable sash and hardware.
D.
Deterioration of wood, metals, vinyl, other materials, and finishes beyond normal
weathering.
E.
Failure of insulating glass.
0.2
Warranty Period:
Architects should specify the longest available warranties for their clients to minimize future life cycle costs.
A.
Window: [Two] [Three] <Insert number>Ten years from date of Substantial Completion.
B.
or date of Sale
C.
aluminum wood or vinyl Coordinate with the paint requirements in Article 2.2.B.
D.
Metal Finish (Baked Enamel): [Five] <Insert number>Ten years from date of Substantial
Completion.
E.
Metal Finish (Fluoropolymer - 70% Kynar 500): Twenty years from date of Substantial
Completion.
PART 2 - PRODUCTS
SCHEDULE 0 - MANUFACTURERS
WOOD WINDOWS
085200 - 6
2.2
WOOD WINDOWS
085200 - 7
SCHEDULE 1 - MATERIALS
Revise paragraph below to prohibit use of finger joints where interior wood is natural finished.
PRODUCT DATA SHEET 0 - Wood: Clear ponderosa pine or another suitable fine-grained lumber; kiln dried to
a moisture content of 6 to 12 percent at time of fabrication; free of visible finger joints, blue stain, knots,
pitch pockets, and surface checks larger than 1/32 inch (0.8 mm) deep by 2 inches (51 mm) wide; waterrepellent preservative treated.
The standard baked enamel finish is suitable for most projects where a high degree of resistance to fading, chalking,
abrasion, chemicals and corrosion is required. The high performance organic finish is recommended for select
projects, colors, and geographic locations that require the exceptional resistance to fading and chalking that only
full-strength 70% Kynar 500 finishes can deliver.
For wood window manufacturers that use extrusions on the window frame and coil on the sash, specify
subparagraphs 1 and 3 together for a baked-enamel finish and subparagraphs 2 and 4 together for a high
performance organic finish. Wood window companies reference AAMA finish standards, not those of NAAMM and
its AA designations.
PRODUCT DATA SHEET 1 - Aluminum Extrusions and Rolled Aluminum for Cladding: Manufacturer's
standard formed sheet or extruded-aluminum cladding, mechanically bonded to exterior exposed wood
members. Provide aluminum alloy and temper recommended by wood window manufacturer for
strength, corrosion resistance, and application of required finish, but not less than 22,000-psi (150-MPa)
ultimate tensile strength, and not less than 16,000-psi (110-MPa) minimum yield strength.
1.1
1.2
1.3
General: Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products"
for recommendations for applying and designating finishes.
Finish designations prefixed by AA comply with the system established by the Aluminum
Association for designating aluminum finishes.
Baked-Enamel Finish for Extrusions and Sheet: Manufacturer's standard baked enamel complying
with AAMA 2603 and paint manufacturer's written specifications for cleaning, conversion coating,
and painting.
Manufacturers full range of colors varies dramatically from one manufacturer to another.
A.
1.4
Color: [White] [Bronze] [Brown] [Beige] [Tan] [Poplar White] [Putty] [Morning Sky
Gray] [Hartford Green] [Hemlock Green] [Brick Red] [Black] [As selected by
Architect from manufacturer's full range] [Custom color as selected by Architect]
<Insert color>.
High-Performance Organic Finish for Extrusions and Sheet: AA-C12C42R1x (Chemical Finish:
cleaned with inhibited chemicals; Chemical Finish: acid-chromate-fluoride-phosphate conversion
coating; Organic Coating: as specified below). Prepare, pretreat, and apply coating to exposed
metal surfaces to comply with coating and resin manufacturers' written instructions.
A 70 percent polyvinylidene fluoride complies with AAMA 2605 and exceeds the requirements of AAMA 2604.
A.
WOOD WINDOWS
1.5
Baked-Enamel Finish for Coil: Manufacturer's standard baked enamel complying with
AAMA 620 and paint manufacturer's written specifications for cleaning, conversion coating, and
painting.
Manufacturers full range of colors varies dramatically from one manufacturer to another.
A.
Color: [White] [Bronze] [Brown] [Beige] [Tan] [Poplar White] [Putty] [Morning Sky
Gray] [Hartford Green] [Hemlock Green] [Brick Red] [Black] [As selected by
Architect from manufacturer's full range] [Custom color as selected by Architect]
<Insert color>.
Retain subparagraph below for premium finish offered by some manufacturers for coil for rolled aluminum
cladding. Delete if another finish is retained.
1.6
High-Performance Organic Finish for Coil: Manufacturer's standard high performance finish
complying with AAMA 620 and paint manufacturer's written specifications for cleaning,
conversion coating, and painting.
A.
Retain first paragraph below only for vinyl-clad wood windows.Pella does not offer vinyl-clad wood windows.
PRODUCT DATA SHEET 2 - Vinyl for Cladding: Consisting of a rigid PVC sheath, made from PVC
complying with ASTM D 4726, not less than 35-mil (0.9-mm) average thickness, in permanent, integral
color, [white] [bronze] [tan] <Insert color> finish, mechanically bonded to exterior wood sash and
frame members.
PRODUCT DATA SHEET 3 - Wood Trim and Glazing Stops: Material and finish to match frame members.
Pella, like most wood window companies, does not supply clad trim in the form of clad-wood material.
PRODUCT DATA SHEET 4 - Clad Trim and Glazing Stops: [Hollow extrusions] [Roll-formed sheet
material] [Clad-wood material] and finish to match clad frame members.
PRODUCT DATA SHEET 5 - Fasteners: Aluminum, nonmagnetic stainless steel, epoxy adhesive, or other
materials warranted by manufacturer to be noncorrosive and compatible with wood window members,
cladding, trim, hardware, anchors, and other components.
5.1
Exposed Fasteners: Unless unavoidable for applying hardware, do not use exposed fasteners. For
application of hardware, use fasteners that match finish of member or hardware being fastened, as
appropriate.
WOOD WINDOWS
085200 - 9
Weather-Stripping Material:
Elastomeric cellular preformed gaskets complying with
ASTM C 509.
Weather-Stripping Material: Dense elastomeric gaskets complying with ASTM C 864.
Weather-Stripping Material: Manufacturer's standard system and materials complying with
AAMA/WDMA 101/I.S.2/NAFS.
Weather Seals: Provide weather stripping with integral barrier fin or fins of semirigid,
polypropylene sheet or polypropylene-coated material. Comply with AAMA 701/702.
PRODUCT DATA SHEET 10 - Replaceable Weather Seals: Comply with AAMA 701/702.
SCHEDULE 2 - WINDOW <Insert drawing designation>
Pella does not offer horizontal sliding wood windows.
PRODUCT DATA SHEET 0 - Window Type: [Casement] [Double hung] [Fixed] [Horizontal sliding]
[Projected awning] [Single hung] [Bay] [Bow] [Specialty product] [As indicated on Drawings] [As
indicated in a schedule] <Insert window type>.
Pella recommends the use of the performance designation method. All paragraphs below that do not comply with
this method have been deleted.
PRODUCT DATA SHEET 1 - AAMA/WDMA Performance Requirements:
Provide wood windows of
performance indicated that comply with AAMA/WDMA 101/I.S.2/NAFS[ unless more stringent
performance requirements are indicated].
building code or the
WOOD WINDOWS
085200 - 10
Consider retaining subparagraph below if test performance method is selected for specifying windows and
designating a performance class does not conflict with basic wind speed and performance testing indicated.
Retaining this subparagraph is not required if test performance method is selected for specifying windows but it may
be useful to establish a quality level and testing protocol per AAMA/WDMA 101/I.S.2/NAFS for windows. For
example, life-cycle testing is required by AAMA/WDMA 101/I.S.2/NAFS for operable AW class windows only.
1.7
Performance Class: [R] [LC] [C] [HC] [AW].
The CRF is a common specification for metal windows because the frames and sash are highly conductive and thus
susceptible to condensation in cold climates. However, since wood is a natural insulator, condensation resistance is
not typically specified for wood windows.
PRODUCT DATA SHEET 2 - Condensation-Resistance Factor (CRF): Provide wood windows tested for
thermal performance according to AAMA 1503, showing a CRF of [45] [52] <Insert value>.
NFRC 100 is most commonly used with wood windows.
PRODUCT DATA SHEET 3 - Thermal Transmittance: Provide wood windows with a whole-window, U-factor
maximum indicated at 15-mph (24-km/h) exterior wind velocity and winter condition temperatures when
tested according to [AAMA 1503] [ASTM E 1423] [NFRC 100].
U-factors lower than 0.40 typically require low-E glass. U-factors lower than 0.30 typically require low-E glass
and triple glazing. Coordinate U-factor with Article 2.4. Paragraph B.
3.1
U-Factor: [0.35 Btu/sq. ft. x h x deg F (2.0 W/sq. m x K)] [0.40 Btu/sq. ft. x h x deg F (2.3
W/sq. m x K)] [0.43 Btu/sq. ft. x h x deg F (2.5 W/sq. m x K)] [0.60 Btu/sq. ft. x h x deg F (3.4
W/sq. m x K)] <Insert value appropriate to system of measure> or less.
Coordinate SHGC with Article 2.4. Paragraph B. Two additional thermal performance criteria that are frequently
specified in projects that incorporate day lighting of interior spaces are visible light transmission and ultra-violet
light transmission.
WOOD WINDOWS
085200 - 11
Maximum Rate: 0.3 cfm/sq. ft. (5 cu. m/h x sq. m) of area at an inward test pressure of 1.57
lbf/sq. ft. (75 Pa).
Test pressure in subparagraph above is equivalent to 25-mph (40-km/h) wind speed and is typically used to test R, C,
and LC performance classes; test pressure in first subparagraph below is equivalent to a 50-mph (80-km/h) wind
speed and is typically used to test HC and AW performance classes.
7.2
Maximum Rate: 0.3 cfm/sq. ft. (5 cu. m/h x sq. m) of area at an inward test pressure of 6.24
lbf/sq. ft. (300 Pa).
7.3
Maximum Rate: <Insert rate and test pressure.>
PRODUCT DATA SHEET 8 - Water Resistance: No water leakage as defined in AAMA/WDMA referenced test
methods at a water test pressure equaling that indicated, when tested according to
AAMA/WDMA 101/I.S.2/NAFS, Water Resistance Test.
Retain first subparagraph below if performance equal to minimum for all other classes set by
AAMA/WDMA 101/I.S.2/NAFS is required. Retain second subparagraph if performance equal to minimum for
AW class windows set by AAMA/WDMA 101/I.S.2/NAFS is required for Project. Revise either subparagraph if
AAMA/WDMA 101/I.S.2/NAFS limit for test pressure of 15 lbf/sq. ft. (720 Pa) does not suit Project. Revising
either subparagraph without verifying with manufacturers that they have tested to greater pressures risks requiring
additional testing.
8.1
8.2
8.3
Test Pressure: 15 percent of positive design pressure, but not less than 2.86 lbf/sq. ft. (140 Pa) or
more than 15 lbf/sq. ft. (720 Pa).
Test Pressure: 20 percent of positive design pressure, but not more than 15 lbf/sq. ft. (720 Pa).
Test Pressure: <Insert percent and pressure.>
WOOD WINDOWS
085200 - 12
Delete paragraph below if no operable windows. Auxiliary tests below consist of a different combination of tests for
each type of operable window.
PRODUCT DATA SHEET 11 - Operating Force and Auxiliary (Durability)
AAMA/WDMA 101/I.S.2/NAFS for operating window types indicated.
Tests:
Comply
with
Model building codes and ASCE 7 establish criteria for buildings in hurricane-prone locations. Authorities having
jurisdiction may accept other test methods and protocols. Verify requirements of authorities having jurisdiction.
PRODUCT DATA SHEET 12 - Windborne-Debris Resistance: Provide glazed windows capable of resisting
impact from windborne debris, based on the pass/fail criteria as determined from testing glazed windows
identical to those specified, according to [ASTM E 1886 and testing information in ASTM E 1996]
[or] [AAMA 506] <Insert test method> and requirements of authorities having jurisdiction.
SCHEDULE 3 - GLAZING
PRODUCT DATA SHEET 0 - Glass and Glazing Materials: Refer to Division 08 Section "Glazing" for glass
units and glazing requirements applicable to glazed wood window units.
Pella offers many additional standard glass options beyond those indicated below. Option 2 is typically used with
tinted glass rather than clear glass. Option 3 is the typical solution for clear glass with low-E coatings and argon
gas. Option 4 is typical for high altitude glass with low-E coatings.
PRODUCT DATA SHEET 1 - Glass <Insert drawing designation>:
[Clear, insulating-glass units]
[Clear[Gray][Bronze][Green] tint, insulating-glass units, with low-E coating pyrolytic on second
surface or sputtered on second or third surface,] [Clear, insulating-glass units, argon gas filled, with
low-E coating pyrolytic on second surface or sputtered on second or third surface,] [Clear,
insulating-glass units with low-E coating sputtered on second surface] <Insert glass type,
description, and performance requirements> complying with Division 08 Section "Glazing."
This is preferred since much of Division 08 Section Glazing pertains to field glazing, which is very uncommon
with wood windows.
PRODUCT DATA SHEET 2 - Glazing System: [Manufacturer's standard factory-glazing system that
produces weathertight seal.] [Manufacturer's standard factory-glazing system that produces
weathertight seal and complies with requirements for windborne-debris resistance.]
[Manufacturer's standard factory-glazing system as indicated in Division 08 Section Glazing. ]
<Insert glazing requirements.>
WOOD WINDOWS
085200 - 13
Pella does not offer wood sliding windows.Retain three paragraphs below for horizontal-sliding windows. Retain
one option in first paragraph or delete both options if not critical.
PRODUCT DATA SHEET 2 - Sill Cap/Track: [Extruded-aluminum track with natural anodized finish]
[Rigid PVC or other weather-resistant plastic track with manufacturer's standard integral color],
of thickness, dimensions, and profile indicated; designed to comply with performance requirements
indicated and to drain to the exterior.
PRODUCT DATA SHEET 3 - Locks and Latches: Designed to allow unobstructed movement of the sash across
adjacent sash in direction indicated and operated from the inside only.[ Provide custodial locks.]
PRODUCT DATA SHEET 4 - Roller Assemblies: Low-friction design.
Pella, like most wood window manufacturers, does not offer push-bar operators for awnings or casements.Retain
paragraph above for horizontal-sliding windows. Retain paragraph below for awning windows with fixed screens
and to suit product.
WOOD WINDOWS
085200 - 14
Operation Function: All ventilators move simultaneously and securely close at both jambs without
using additional manually controlled locking devices.
Friction hinges are rarely used on wood awnings or casements so paragraph H can be deleted. The rotary operator
and sliding hinges are typically designed to hold the window open at nearly any point along its path of travel.
PRODUCT DATA SHEET 7 - Four- or Six-Bar Friction Hinges: Comply with AAMA 904.
If retaining paragraph above and subparagraphs below for manually operated, screened outswinging casement
windows, push-bar operators, screen wickets, or side-hinged screens are required.
7.1
7.2
Safety Devices: Limit clear opening to [4 inches (100 mm)] [6 inches (150 mm)] <Insert
dimension> for ventilation; with custodial key release.
Electrical operators are also an option for windows in these types of locations.
PRODUCT DATA SHEET 9 - Pole Operators: Tubular-shaped anodized aluminum; with rubber-capped lower
end and standard push-pull hook at top to match hardware design; of sufficient length to operate window
without reaching more than 60 inches (1500 mm) above floor; 1 pole operator and pole hanger per room
that has operable windows more than 72 inches (1800 mm) above floor.
For casements and awnings a single handle locking system (sometimes referred to as a unison lock) that controls one
or more locking points is recommended to minimize long-term deformation of the window stiles.
PRODUCT DATA SHEET 10 - Single handle locking system shall operate positive-acting arms that reach out
and pull the sash into a locked position: one installed on sash 29 inches and smaller in height, two unison
operating locks installed on sash over 29 inches frame height.
SCHEDULE 5 - INSECT SCREENS
For casements and awnings, screens are located on the inside. For double hungs, screens are located on the
outside.
PRODUCT DATA SHEET 0 - General: Design windows and hardware to accommodate screens in a tightfitting, removable arrangement, with a minimum of exposed fasteners and latches. Fabricate insect
WOOD WINDOWS
085200 - 15
Aluminum Tubular Frame Screens: Comply with SMA 1004 or SMA 1201, "Specifications for
Aluminum Tubular Frame Screens for Windows," [Residential R-20] [Architectural C-24]
[Monumental M-32] class.
Screen Type for Casement Windows: [Full] [Pella's Rolscreen].
Screen Type for Awning Windows: Full.
Screen Type for Double-Hung Windows: [Full] [Half].
PRODUCT DATA SHEET 1 - Aluminum Insect Screen Frames: Manufacturer's standard aluminum alloy
complying with SMA 1004 or SMA 1201. Fabricate frames with mitered or coped joints or corner
extrusions, concealed fasteners,[ adjustable rollers,] and removable PVC spline/anchor concealing edge
of frame.
1.1
Aluminum Tubular Framing Sections and Cross Braces: Roll formed from aluminum sheet with
minimum wall thickness as required for class indicated.
Most wood window companies do not offer an anodized finish on the screen frame. Interior screens typically have
one or two finish options. Exterior screens will typically match the color of the aluminum cladding. For primed
wood exteriors, the screen color is typically white.
1.2
Finish for Interior Screens: [Anodized aluminum] [Baked-on organic coating] <Insert finish> in
manufacturer's standard color [Champagne] [White].
1.3
Finish for Exterior Screens: [Baked-on organic coating] [Match color and finish of aluminum
cladding] [White].
1.4
Finish: [Anodized aluminum] [Baked-on organic coating] <Insert finish> in color selected by
Architect from manufacturer's full range.
1.5
Finish: Manufacturer's standard.
PRODUCT DATA SHEET 2 - Glass-Fiber Mesh Fabric: [18-by-14 (1.1-by-1.4-mm) or 18-by-16 (1.0-by-1.1mm)] [20-by-20 (0.85-by-0.85-mm) or 20-by-30 (0.85-by-0.42-mm)] <Insert type> mesh of PVCcoated, glass-fiber threads; woven and fused to form a fabric mesh resistant to corrosion, shrinkage,
stretch, impact damage, and weather deterioration; in the following color. Comply with ASTM D 3656.
Pella offers black.
2.1
PRODUCT DATA SHEET 3 - Aluminum Wire Fabric: 18-by-16 (1.1-by-1.3-mm) mesh of 0.011-inch- (0.28mm-) diameter, coated aluminum wire.
3.1
PRODUCT DATA SHEET 4 - High Transparency Mesh Fabric: [21-by-17 (0.85-by-1.0-mm)] PVDF mesh with
minimum 78 percent visible light transmission screen cloth complying with FS L-S-125B and SMA 1004
or SMA 1201 that is resistant to corrosion, shrinkage, stretch, impact damage, and weather deterioration;
black.
Retain paragraph below for screened-window units with outward-opening sash or ventilators where wickets are
necessary for sash or ventilator operation.Pella, like most wood window manufacturers, does not offer wickets.
WOOD WINDOWS
085200 - 16
Material: [Extruded, rigid PVC] [Extruded, aluminum] [Extruded, aluminum exterior and
wood veneer interior] [Prefinished wood] [Primed wood] [Unfinished wood].
Design: [Rectangular] [Diamond] [Prairie] [9-Lite Prairie] <Insert design>.
Color: [White] [Tan/White] [Match cladding color/Unfinished] [Unfinished] [Bronze]
<Insert color>.
Width: [3/4 inch (19 mm)] [1-1/4 inches (31.75 mm)] <Insert dimension>.
For permanent muntins, the following options are available for each of the Pella brands noted below. For a pictorial
view and description of the many Pella muntin options, visit the link noted below.
http://www.pellacommercial.com/overview/muntin.asp
With Architect Series products, the permanent muntins are made of aluminum or wood. Material and color options
include [Extruded, aluminum][Match cladding] or [Primed wood] on the exterior and [Unfinished wood] or [Primed
wood] on the interior. Between-the-glass foam spacer is included. Several widths and patterns are available.
With Designer Series products, there are no permanent muntin options.
With ProLine products, the permanent muntins are made of aluminum or wood. Material and color options include
[Extruded, aluminum][Match cladding] on the exterior and [Unfinished wood] or [Prefinished wood - White] on the
interior. Between-the-glass foam spacer is not included. Width is always 7/8. Design is always rectangular.
PRODUCT DATA SHEET 1 - Dividers (Permanent Muntins): Provide dividers in designs indicated for each
sash lite, [two per sash with between-the-glass foam spacer] [two per sash with no between-the-glass
spacer].
1.1
WOOD WINDOWS
085200 - 17
Pella does not offer storm panels of the type noted below.
PRODUCT DATA SHEET 2 - Storm Panels: Provide removable auxiliary glazing panels of clear float glass for
each fixed and operating sash of window units. Glass shall comply with ASTM C 1036, Type I,
Quality q3. Provide glass of thickness required to comply with requirements in Division 08 Section
"Glazing," Frame, preglaze, and attach storm windows to the sash according to manufacturer's published
standards.[ Omit storm panels on sash glazed with insulating glass.]
Pella color options are noted below.
PRODUCT DATA SHEET 3 - Integral Louver Blinds: Provide remotely operated cordless horizontal louver
blinds in the space between two panes of glass. Construct blinds of aluminum slats, approximately 5/8
inch (15.9mm)1 inch (25 mm) wide, with polyester fiber cords, equipped for [tilting only] [tilting,
raising, and lowering] by standard operating hardware located on inside face of sash.
3.1
Color: [Bisque] [Celery] [Charcoal] [Garnet] [Golden] [Marine] [Mocha] [Pewter] [Poplar
White] [White].
PRODUCT DATA SHEET 4 - Integral Cordless Cellular Fabric Shades: Provide fabric shades in the space
between two panes of glass. Construct shades of cellular fabric, approximately 3/4 inch (19 mm) wide,
with polyester fiber cords, equipped for raising and lowering, by standard operating hardware located on
inside face of sash.
4.1
4.2
SCHEDULE 7 - FABRICATION
PRODUCT DATA SHEET 0 - Fabricate wood windows in sizes indicated.
assembling components and anchoring windows.
PRODUCT DATA SHEET 1 - Fabricate wood windows that are reglazable without dismantling sash or
ventilator framing.
PRODUCT DATA SHEET 2 - Weather Stripping: Provide full-perimeter weather stripping for each operable
sash and ventilator, unless otherwise indicated.
2.1
Double-Hung Windows: Provide weather stripping only at horizontal rails of operable sash.
PRODUCT DATA SHEET 3 - Factory machine windows for openings and for hardware that is not surface
applied.
PRODUCT DATA SHEET 4 - Mullions: Provide mullions and cover plates as shown, matching window units,
complete with anchors for support to structure and installation of window units. Allow for erection
tolerances and provide for movement of window units due to thermal expansion and building deflections,
as indicated. Provide mullions and cover plates capable of withstanding design loads of window units.
WOOD WINDOWS
085200 - 18
PRODUCT DATA SHEET 8 - Complete fabrication, assembly, finishing, hardware application, and other work
in the factory to greatest extent possible. Disassemble components only as necessary for shipment and
installation. Allow for scribing, trimming, and fitting at Project site.
SCHEDULE 8 - INTERIOR WOOD FINISHES
or vinyl- Pella Architect Series, Designer Series, and ProLine products are available with an unfinished interior.
Pella Architect Series and Designer Series are also available with a factory-primed interior. Pella ProLine products
are also available with a factory-finished white interior.
PRODUCT DATA SHEET 0 - Factory-Primed Windows: Provide manufacturer's standard factory-prime coat
[complying with WDMA T.M. 11] <Insert specific requirements for factory-prime coat if any> on
exposed [exterior] [and] [interior] wood surfaces.
PRODUCT DATA SHEET 1 - Factory-Finished Windows: Provide manufacturer's standard factory finish
[complying with WDMA T.M. 12] <Insert manufacturer's standard finish>. Apply finish to exposed
exterior and interior wood surfaces.
1.1
Color: [White] [Brown] [Gray] [As selected by Architect from manufacturer's full range]
<Insert color>.
PART 3 - EXECUTION
SCHEDULE 0 - EXAMINATION
PRODUCT DATA SHEET 0 - Examine openings, substrates, structural support, anchorage, and conditions, with
Installer present, for compliance with requirements for installation tolerances and other conditions
affecting performance of work. Verify rough opening dimensions, levelness of sill plate, and operational
clearances. Examine wall flashings, vapor retarders, water and weather barriers, and other built-in
components to ensure a coordinated, weathertight window installation.
WOOD WINDOWS
085200 - 19
Masonry Surfaces: Visibly dry and free of excess mortar, sand, and other construction debris.
Wood Frame Walls: Dry, clean, sound, well nailed, free of voids, and without offsets at joints.
Ensure that nail heads are driven flush with surfaces in opening and within 3 inches (76 mm) of
opening.
Metal Surfaces: Dry; clean; free of grease, oil, dirt, rust, corrosion, and welding slag; without
sharp edges or offsets at joints.
Proceed with installation only after unsatisfactory conditions have been corrected.
SCHEDULE 1 - INSTALLATION
PRODUCT DATA SHEET 0 - Comply with Drawings, Shop Drawings, and manufacturer's written instructions
for installing windows, hardware, accessories, and other components.
PRODUCT DATA SHEET 1 - Install windows level, plumb, square, true to line, without distortion or impeding
thermal movement, anchored securely in place to structural support, and in proper relation to wall
flashing and other adjacent construction.
Sill members should not be set in a bed of sealant. But rather, sills should be shimmed and then sealed as described
in paragraphs E and F below.
PRODUCT DATA SHEET 2 - Install windows to be weather-tight and freely operatingSet sill members in bed of
sealant or with gaskets, as indicated, for weathertight construction.
PRODUCT DATA SHEET 3 - Separate aluminum and other corrodible surfaces from sources of corrosion or
electrolytic action (dissimilar materials, treated lumber, etc.) at points of contact with other materials.
PRODUCT DATA SHEET 4 - For fin method of attachment, integrate window system installation with exterior
weather-resistant barrier using flashing/sealant tape. Apply and integrate flashing/sealant tape with
weather-resistant barrier using watershed principles in accordance with window manufacturer's
instructions.
PRODUCT DATA SHEET 5 - Place interior seal around window perimeter using insulating foam sealant to
maintain continuity of building thermal and air barrier.
PRODUCT DATA SHEET 6 - Seal window to exterior wall cladding with sealant and related backing materials
at perimeter of assembly.
PRODUCT DATA SHEET 7 - Leave window units closed and locked.
SCHEDULE 2 - ADJUSTING, CLEANING, AND PROTECTION
PRODUCT DATA SHEET 0 - Adjust operating sashes and ventilators, screens, hardware, and accessories for a
tight fit at contact points and weather stripping for smooth operation and weathertight closure. Lubricate
hardware and moving parts.
PRODUCT DATA SHEET 1 - Clean exposed surfaces immediately after installing windows. Avoid damaging
protective coatings and finishes. Remove excess sealants, glazing materials, dirt, and other substances.
PRODUCT DATA SHEET 2 - Clean factory-glazed glass immediately after installing windows. Comply with
manufacturer's written recommendations for final cleaning and maintenance. Remove nonpermanent
labels, and clean surfaces.
WOOD WINDOWS
085200 - 20
WOOD WINDOWS
085200 - 21