Beruflich Dokumente
Kultur Dokumente
Start-up wizard
The Start Up Wizard is activated when the power to the drive is turned on for the first time, or if the
Start Up Wizard is activated from the System menu (P6.5.3) AND the power is turned OFF and back
ON.
The Start-up Wizard is a feature on the control keypad to facilitate the commissioning of the frequency converter. If selected active (default), the Start-up Wizard prompts the operator for the language and application of his/her choice plus for the values for a set of parameters common to all
applications as well as for a set of application-dependent parameters.
Always accept the value with the Enter button, scroll options or change values with the Browser
buttons (up and down arrows). More information on the use of the control panel in Chapter 7 of the
User's Manual.
Startup wizard
enter
Press enter
Language
enter
English
Application
Local/Remote control
application:
I/O reference A (P2.1.11)
I/O reference B (P2.1.12)
enter
Standard
Setup starts
enter
Press enter
0.00 Hz
Multi-step speed
application:
I/O reference (P2.1.11)
enter
Multi-purpose control
application:
I/O reference (P2.1.11)
Pump and fan control
application:
Act value 1 select (P2.2.1.9)
PID controller ref (P2.1.11)
No. of aux pumps (P2.9.1)
Repeat setup?
<No
Min Frequency
Standard application:
I/O reference (P2.1.11)
Yes>
Monitoring values
Code
Signal name
Unit
V1.1
V1.2
V1.3
V1.4
V1.5
V1.6
V1.7
V1.8
V1.9
V1.10
V1.11
V1.12
V1.13
V1.14
V1.15
Output frequency
Frequency reference
Motor speed
Motor current
Motor torque
Motor power
Motor voltage
DC-link voltage
Unit temperature
Motor temperature
Voltage input
Current input
DIN1, DIN2, DIN3
DIN4, DIN5, DIN6
DO1, RO1, RO2
Hz
Hz
rpm
A
%
%
V
V
C
%
V
mA
V1.16
mA
M1.17
Multimonitoring items
Fault
code
1
2
3
5
6
7
8
9
10
11
12
13
14
15
16
17
22
24
25
26
29
31
34
36
37
38
39
40
41
42
43
44
45
50
51
52
53
54
56
Fault
Overcurrent
Overvoltage
Earth fault
Charging switch
Emergency stop
Saturation trip
System fault
Undervoltage
Input line supervision
Output phase supervision
Brake chopper supervision
Frequency converter
undertemperature
Frequency converter
overtemperature
Motor stalled
Motor overtemperature
Motor underload
EEPROM checksum fault
Counter fault
Microprocessor watchdog fault
Start-up prevented
Thermistor fault
IGBT temperature (hardware)
CAN bus communication
Control unit
Device change
Device added
Device removed
Device unknown
IGBT temperature
Brake resistor
Encoder fault
Device change (default param.)
Device added (default param.)
Analogue input Iin < 4mA
(selected signal range 4-20 mA)
External fault
Keypad communication fault
Fieldbus fault
Slot fault
PT100 temperature fault
Parameter name
ID1033
ID1034
ID1035
ID1036
Parameter code in
PID ctrl applic.
2.2.46
2.2.47
2.2.48
2.2.49
Parameter code in
Pump&Fan ctrl applic.
2.9.29
2.9.30
2.9.31
2.9.32
Example:
The actual value signal sent from a sensor (in mA) represents the amount of waste water pumped
from a tank per second. The signal range is 0(4)20mA. Instead of receiving the level of the actual
value signal (in mA) on the display, you wish to receive the amount of water pumped in m3/s. You
then set a value for par. ID1033 to correspond to the minimum signal level (0/4 mA) and another
value for par. ID1034 to correspond to the maximum signal level (20 mA). The number of decimals
needed can be set with par. ID1035 and the unit (m3/s) with par. ID1036. The level of the actual value
signal is then scaled between the set min and max values and displayed in the selected unit.
The following units can be selected (par. ID1036):
Value
0
1
2
3
4
5
6
7
8
9
10
11
12
13
Unit
Not Used
%
C
m
bar
mbar
Pa
kPa
PSI
m/s
l/s
l / min
l/h
m3 /s
On keypad
14
m3 /min
m3/m
%
C
m
bar
mbar
Pa
kPa
PSI
m/s
l/s
l/m
l/h
m3/s
Value
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Unit
m3 /h
F
ft
gal / s
gal / min
gal / h
ft3 / s
ft3 / min
ft3 / h
A
V
W
kW
Hp
On keypad
m3/h
F
ft
GPS
GPM
GPH
CFS
CFM
CFH
A
V
W
kW
Hp
NOTE: The maximum number of characters that can be shown on keypad is 4. This means that in
some cases the display of the unit on the keypad does not comply with the standards.
Selection of language
1.
2.
3.
4.
READY
I/Ot erm
I/Oterm
Language
System Menu
S1!S11
English
READY
READY
I/Ot erm
I/Oterm
Language
enter
English
Langue
Francais
Selection of application
1.
2.
3.
4.
STOP
READY
READY
I/Oterm
I/Oterm
Application
System Menu
S1!S11
STOP
Standard
STOP
READY
Application
Standard
READY
I/O term
I/O term
enter
Application
Multi-step
R EADY
I/Oterm
R EADY
I/Ote rm
Expander boards
A:NXOPTA1
G1!G1
G1!G5
STOP
I/Oterm
R EADY
STOP
I/Ote rm
English
Browse
READY
I/Ote rm
READY
I/Ote rm
Fault history
H1!H3
STOP
I/Oterm
11 Output phase
T1!T7
FAULT
STOP
I/Ote rm
Active faults
F0
or:
R EADY
ST OP
Control Place
I/O Terminal
R EADY
RU N
I/Ote rm
R EADY
I/Ote rm
Monitor
V1!V15
17
enter
Browse Change
value
READY
L oc al
Basic parameters
P1!P15
RUN
FAULT
Operation days
R EADY
I/Ote rm
Parameters
G1!G9
STOP
R EADY
I/Ote rm
Keypad control
P1!P3
17
I/Ote rm
11 Output phase
F
T1 !T7
I/Ote rm
Operation days
FAULT
I/Ote rm
ST OP
Change
value
enter
Language
READY
P1!P3
R EADY
I/Ote rm
System Menu
S1!S9
Parameters
Min Frequency
13.95 Hz
READY
I/Oterm
Output frequency
13.95 Hz
No editing!
enter
Browse Change
value
NOTE! There are some special functions that can be performed when in the M3 menu:
start
button pushed
Select the keypad as the active control place by keeping the
down for 3 seconds when the motor is running. The keypad will become the active
control place and the current frequency reference and direction will be copied to the
keypad.
stop
Note that if you are in any other than M3 menu these functions will not work.
If you are in some other than M3 menu and try to start the motor by pressing the START button
when the keypad is not selected as the active control place you will get an error message Keypad
Control NOT ACTIVE.
NOTE 2:
stop