Beruflich Dokumente
Kultur Dokumente
DL
LL
qallow
850 kN
620 kN
tftg
600 mm
1.8 m
200 kPa
bottom of flg
soil
conc
f'c
fy
b
column width
of main bars
15 kN/m3
23.5 kN/m3
20.7 Mpa
275 Mpa
3000 mm
400 mm
25 mm
Solution
qeff
167.9 kPa
Aftg
x
8.755211 mm2
2.958921
~
qult
249.3333 kPa
3m
~ 0.24933 Mpa
3000
d
3000
bw
400
400
1300
1933.633 d
972400
748 d
362.6148 mm
PUNCHING SHEAR
(Two Way Shear)
3000
mm
400
3000
+d
d/2
400 + d
Vult = Vc
Vc
bo
d
400 + d
462.7226 mm
dbeam
362.6148 mm
dpunching
therefore,
462.7226 mm
d =
462.7226 mm
dinitial
487.5 mm
Mult
w
210.6867 kN - m
0.017793
0.001339
min
0.005091
therefore, use =
>
462.723 mm
(OK!)
0.00133931
0.005091
As
7067.036 mm2
14.39685
say use
>
15
15
25 mm bars
0.249333
2062.54212078 d
5.2 d2
A
5.405689 d2
d
d
462.7226 mm
-881.1723 mm
B
+ 2262 d
2244000
C
-2204107
39893
0.59 w2
w
w
1.677122
0.017793
-1 w
0.017606
DETAILING:
1.8 m
0.6 m
160000 +
-
199.4667 d
800 d +
-
d2
0.249333 d2
DETAILING:
N
SYMBOL
462.72
15
25 mm temperature bars
25 mm main bars
3000
mm
N
SYMBOL
600 mm
15
Part II
ANSWERS
B
CORRECT!
1 What is the tangent distance of a curve whose 210m long chord subtended by
a 62 central angle?
a. 146.54 m
B
WRONG!
b. 122.50 m
c. 172.62m
of +5%. The length of the curve on the left side (P.C. is 60m), what is the elevation
of P.C. if the vertex is at elevation of 100m?
b. 96m
c. 89m
Cross-section
-2.6
-1.84
a. 2:1
4.63
-0.42
b. 1.5:1
c. 2.5:1
d. 3:1
5 A piece of ground 10m square has the following offsets at the corners: 6.2m, 7.8m,
5.1m and 8.0m. If the offsets are the measured elevation from the same datum,
determine the voplume of earthworks.
a. 204.775m3
D
WRONG!
d. 97m
B
WRONG!
d. 180.45m
3 An unsymmetrical parabolic curve has a forward tangent of -8% and back tangent
a. 88m
A
WRONG!
d. 165.44 m
a. 147.78m
A
WRONG!
c. 136.24 m
b. 203.934m3
c. 201.023m3
d. 342.843m3
6 The standard specification for the Fineness of Cement shall not be less than _____.
a. 79%
C
WRONG!
b. L/24
c. L/28
d. L/10
b. 1.87
c. 1.9
d. 1.7
b. 1,140 kN
c. 1,690 kN
d. 1,370 kN
11 For a singly reinfoced rectagular beam of width b(mm) and effective depth of d(mm),
the ultimate moment in N-mm, Mu=f'cbd 2w(1-0.59w). The unit for f'c and fy is:
b. MN/mm2
c. ksi
d. MN/m2
12 This is the material that acts as lubricant during pavement and compaction and as
the cementing material that hols the aggregates together to form a solid mass
after compaction.
a. Glue
B
WRONG!
d. r4/4
eccentricity of 450mm from the neutral axis along the shorter side.
a. N/m2
A
WRONG!
c. r4/16
10 Calculate the nominal axial load capacity of the column that can be applied at an
a. 954 kN
A
WRONG!
b. d4/4
C
WRONG!
d. 76%
B
WRONG!
c. 78%
B
WRONG!
b. 40%
b. Binder
c. Filler
13 The largest unit stress that the material achieved in a tension test is ___________.
a. Tensile Strength
b. Yield Strength
c. Ductility
d. Shear Modulus
C
WRONG!
3
3
14 Find the porosity ratio of a given soil sample with V v=0.012m and V=0.1m .
a. 12%
A
WRONG!
b. 0.012%
c. 0.12%
d. 1.2%
TOTAL SCORE
b. 1.0
c. 0.5
d. 0.7
Remarks
subtended by
d. 165.44 m
us of 420m is
d. 180.45m
he same datum,
d. 342.843m3
be applied at an
d. 1,370 kN
ompaction and as
m a solid mass
st is ___________.
d. Shear Modulus
Review