Beruflich Dokumente
Kultur Dokumente
lt
Development board for Sierra SL6087and XM01100
Version 1.2
20.06.2010
Technical Specification
Version 1.2
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
Introduction ............................................................................. 3
Development Board top view ................................................. 3
Development Board bottom view .......................................... 5
SL6087->Q24 adapter board...................................................... 6
XM0110 daughter board ........................................................... 7
Connector description .............................................................. 8
Switch description: ................................................................. 12
LED description: ...................................................................... 12
Introduction
Development Board for SL6087 and XM0110 has been designed In order to make
customers development based on Sierra SL6087 and XM0110 easier.
With this board it is possible to test SL6087 and XM0110 capabilities as well as Open
AT programming without making own board. Development board has been equipped with
supply connector, two serial ports, SIM card slot and goldpin connector.
For technical parameters regarding SL6087 and XM0110 please refer to applicable
documentation from Sierra Wireless.
S1 switch
logical level for
ON/OFF signal
S2 Switch
BOOT Or Normal
working mode
selection
J5 Connector
DB Power supply
J3 Connector
60-pin Signal
connector
SW1 Switch
Modem reset
J4 Connector
60-pin connector with
modem signals
Control LED
Additional antenna
connector
U.FL.
For future use
Mini USB
Main antenna
connector
U.FL.
S4 Switch
UART2 or GPIO
mode
J1 Connector
UART 1
J12 Connector
UART 2
1. Development Board for SL6087 and XM0110 component placement
JSIM Slot
Zcze J6
Expansion socket
J7 Connector
Expansion socket
Main antenna
connector
U.FL.
3. SL6087->Q24 adapter board, top view
XM0110 daughter board is a removable expansion board which can help customer to
develop their own project based on XM0110 module. Board should be mounted on J7 and J6
connector of SL6087 adapter board.
GPS
antenna
connector
J7
Connector
J6 Connector
For connection between SL06087 and XM011 serial port UART2 is used. Moreover as a
control signals mentioned below GPIO lines are used:
GPIO22 XM0110 ON/OFF pin
GPIO23 XM0110 reset pin
GPIO21 additional LED (for customer use)
Warning: Since UART2 is used for XM0110 connection, it is not available through J2
connector. Please switch S4 to GPIO position when you use XM0110 daughter board.
Connector description
J1 Connector female DB9 connector for RS-232 communication. UART1 of SL6087 module
is available through this connector. Signals available on this connector are described in table
below:
J2 Connector female DB9 connector for RS-232 communication. UART2 of SL6087 module
is available through this connector. Signals available on this connector are described in table
below:
SL6087 pin
number
41
41
9
41
7
43
8
13
8
16
9
6
12
10
17
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
42,44
18
63
62
45
64
46
37
65
47
14
66
11
73
67
1
5
70
adapter
Pin number
Reserved_41
Reserved_41
SIM-CLK
Reserved_41
~SIM-RST
ON/~OFF
SIM-IO
SPI1-IO/GPIO13 (if R1 is present and R2 is
unsoldered Fig. 4)
or
SDA/GPIO2 (if R4 is present and R1 is
unsoldered Fig. 4)
SIM-VCC
SPI1-CLK/GPIO12 (if R2 is present and R3 is
unsoldered Fig. 4)
lub
SCL/GPIO1 (if R3 is present and R2 is
unsoldered Fig. 4)
VBAT
BOOT
NOT USED
~RESET
NOT USED
INT1
NOT USED
CT103-TXD2
PCM-SYNC
CT104-RXD2
NOT USED
GPIO24
PCM-OUT
~CT106-CTS2
NOT USED
SPI1-I
PCM-IN
~SPI1-I_CS
NOT USED
~CT105-RTS1
PCM-CLK
CT104-RXD1
ADC2
~CT108-2-DTR1
board
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
48
72
2
40
74
58
57
53
56
54
52
60
53
54
55
56
57
58
59
60
61
71
42,44
3
42,44
42,44
42,44
42,44
68
10
69
~CT105-RTS2
~CT107-DSR1
~CT106-CTS1
ADC1
CT103-TXD1
VCC_2V8
SPKP
MICP
SPKN
MICN
NOT USED
NOT USED
NOT USED
NOT USED
BUZZER0
SIMPRES
~CT109-DCD1
LED0 (w przypadku wysterowania LED0 na 52
pinie pojawia si napicie VBAT)
INT0
~CT125-RI
VBAT
BAT-RTC
VBAT
VBAT
VBAT
VBAT
7. 60-pin connector
J4 Connector 60-pin goldpin connector with SL6087 signals LED out (tab.3)
J5 Connector Power supply connector. Supply voltage should be between 7V and 9V with
0,5A current draw capability. Polarization is described on board.
Additional J6 Connector expansion socket for GPS XM0110. Pin description:
J6 pin number
1
2
3
4
SL6087 pin
number
46
45
39
38
SL6087 pin
number
42,44
4
15
JSIM Connector SIM card slot dedicated for SIM card inserting. Signal description:
Switch description:
LED description:
PWR Power LED. This LED is on when Power supply was properly applied
FLH flash LED of SL6087 module showing working state of SL6087 (please refer to SL6087
Product Specification)
Diody UART1 signal LEDs for UART1 interface : TXD, RXD, RTS, CTS, DTS, DSR.
Diody UART2 signal LEDs for UART1 interface: RS-232:TXD, RXD, RTS, CTS.