Beruflich Dokumente
Kultur Dokumente
1:
Answer:
Query: Please explain me about this 16, How SCR codes become 8192, BCZ I didnt saw any
8192 SCR, from Mobile it scans upto 512 only
Primary 512 and secondary 16. 512*16=8192
EXCEPT PRIMARY CCPCH (BCCH) which uses Primary SCR code, other downlink CH's can
use either Primary or secondary SCR Codes, from the set associated with primary SCR code
Du mobile dubai
CH no = 10662, Freq = 10662/5 = 2132.4 DL
UL = 2132.4 - 190 = 1942.4 MHz
Answer:
Query:
The triggering of the event-triggered reporting for an intra-frequency measurement. All events
concerning intra-frequency measurements are labelled 1x where x is a, b, c.
Event 1a: A Primary CPICH enters the Reporting Range (FDD only).
Event 1b: A Primary CPICH leaves the Reporting Range (FDD only).
Event 1c: A Non-active Primary CPICH becomes better than an active Primary CPICH (FDD
only).
Event 1d: Change of best cell (FDD only).
Event 1e: A Primary CPICH becomes better than an absolute threshold (FDD only).
Event 1f: A Primary CPICH becomes worse than an absolute threshold (FDD only).
Event 1g: Change of best cell in TDD.
Event 1h: Timeslot ISCP below a certain threshold (TDD only).
Event 1i: Timeslot ISCP above a certain threshold (TDD only).
Question.3:
Answer:
Query:
TTI (explanation)
TTI is the transmit time interval of a data packet in HSDPA. In EDGE and GPRS it was 10ms.
Hence, get faster throughput in HSDPA.
Question.4:
classify them?
How many RAB's can be established at one time during Mobile TV session,
Answer:
Query:
Answer:
256.
Query:
Need some explanation about CE: like which CH element assign for which
service, how utilizing 256 CH elements and all
One WSPC has 64 channel elements. (256 CE on a site, having 4 WSPC cards) 16 CE for
transmission and signaling. 16 reserved for HSDPA. Rest for voice and video call. One voice call
takes one CE. A video call utilizes 4 CE. 256 CE (4WSPC) will utilize the same 16 CE for
signaling and 16 CE reserved for HSDPA depending on how they have been configured in the
cabinet.
How many CE utilization codes
Question.6:
How many types of Inter System Handovers are there? Clasify any three
Answer:
RxCp is Received signal code power RSCP, and not disabled. DL DPCH is downlink dedicated
physical channel. The UMTS system uses the Downlink DPCH (Downlink Dedicated Physical
Channel) to carry the DPDCH (Dedicated Physical Data Channel) and the DPCCH (Dedicated
Physical Control Channel).
DPDCH - Dedicated Physical Data Channel
The Dedicated Physical Data Channel is a type of uplink dedicated physical channel. It is an I/Q
code, multiplexed within each radio frame. The uplink DPDCH is used to carry
the DCH (Dedicated Channel) transport channel. There may be zero, one, or several uplink
DPDCH on each radio link.
DPCCH - Dedicated Physical Control Channel
The Dedicated Physical Control Channel is a type of uplink dedicated physical channel. It is an
I/Q code, multiplexed within each radio frame. The uplink DPCCH is used to carry
the DCH (Dedicated Channel) transport channel. The uplink DPCCH is used to carry control
information generated at Layer 1.
Question.7:
Answer:
But why the RRC Connection will be released then for above mentioned
Reason.1-> I think its saying that the current serving cell is congested and on the neighbor cell
traffic is high as well. UE sends the RRC connection request message and admission control
rejects it due to congestions. All the three reasons above are related to congestion. i.e blocking in
the cell -> no code available. But in my opinion apart from this
1. UE sends RRC connection request but RNC doesnt receive RRC Connection Request
message due to excessive path loss or when the RNC sends back the RRC Connection
Setup message to UE, The UE does not receive it. So it will release the connection.
(problem is coverage)
2. If the cell/RNC doesnt respond with an RRC Connection Setup message then the
mobile will wait for a specific amount of time, and make the request again. The total
number of requests and the wait time is specified by the network.
This usually happens because:
RNC is not able to receive the message due to a possible faulty synchronisation on the Iub
(DAC Word/10 Mhz) or Sleeping cell problem, UL interference.
Question.8:
If the 3G network has to be utilized most in terms of PS traffic what RSCP and
EcIo thresholds are to be considered.
Answer:
Query:
I want to know this that how to utilize most in terms of PS Traffic, EcIo threshold
could be different according to Site capacity
Here its talking about 2G-3G EcIo. It will handover to 3G once the quality of a 2G serving cell is
--12. That means immediate HO to 3G service. RSCP -115, means it will handover to 2G when
RSCP is very low, keeping low threshold to delay the handover from 3G-2G. And yes you are
right if the site is congested ->high code utilization, PS traffic will be low as well or high NRT RRC
and RAB drops, EcNo threshold can be different.
Question.9:
Answer:
1> User trying to register from far location->Solution to this reason is adjust the tilting
2> Hardware problem->Give a hard reset
Query:
Is this is the only solution, what about Pilot power reduction, or increase,
Adjusting Active Window Size, SCR Conflict, or other parameter to change ?
Yes we can do the pilot power reduction. But increasing window size wont help, as still this far
serving site would be the best server. (We can discuss)
Question 10:
Failures?
Answer:
What are the main reasons for RRC Setup Success Failures or RAB Sutup
Query:
EcNo could be higher in area where sites will be more close to each other and
Interference is high also PN pollution, but how this will effect RRC Setup Success failure, what
about if EcNo is good but RsCp is poor, bcz in remote sites where no Interference there EcNo will
definitely be good but not RsCp, please explain in detail ?
Look even if the sites are close to each other you have to control the foot print of both the sites.
Interference would be high and the quality would be bad if the cell is congested and hence no
more RRC setups will be allowed or the same reason I mentioned due to the radio conditions
RNC does not receive the RRC connection request message or UE doesnt receive RRC
connection setup message. Reasons as follows:
RRC fails due to Handover Control
RRC fails due to Admission control
RRC fails due to BTS
Answer:
Query: This is most Important I have never seen how to and from where to extract the KPIs and
they comes under which KPI set, if possible then please take snap shot of the Reporting suit and
details from where to extract which KPIs
We dont have reporting suite here. We receive a 3G cell report where all these KPIs are there. I
can send u a few reports of reporting suite which I had extracted for sharjah RNC.
Question.12:
Answer:
Query:
High speed shared control channel carries H-ARQ (hybrid automated response request)
information (process number, redundancy version and new data indicator) and (channelization
code set, modulation scheme, transport block size)
Up to 4 logical channels per UE
Shailendra Gairola
Thanks
Adeel
3.