Beruflich Dokumente
Kultur Dokumente
Table of contents
1.
2.
3.
4.
5.
6.
7.
Product overview
General data
Performance range
Applications
Examples of applications
Wastewater definitions
Pump overview
Type keys
Construction
Installation
4
5
5
6
6
6
7
7
Unilift CC
Unilift KP
Unilift AP12
KP Basic
Unilift AP35
Unilift AP35B
Unilift AP50
Unilift AP50B
8
12
16
21
27
32
37
42
Controllers
47
Control box
Level controller
LC 107, LCD 107
LC 108, LCD 108
LC 110, LCD 110
47
47
48
50
51
Accessories
53
53
54
56
Product range
57
Unilift CC
Unilift KP 150
Unilift KP 250
Unilift KP 350
Unilift AP12
Unilift AP35
Unilift AP35B
Unilift AP50
Unilift AP50B
KP Basic
57
58
59
60
61
62
62
63
63
64
65
WebCAPS
WinCAPS
GO CAPS
65
66
67
Product overview
1. Product overview
Unilift CC, KP, AP
Application
Technical data
Sizing
GR A0682
Unilift CC
Unilift AP12
TM03 1851 3205
Drainage
GR 0110
Unilift KP
GR 7913
KP Basic
Unilift AP35B
TM03 8259 0907
Effluent
Unilift AP35
Unilift AP50B
TM03 8260 0907
Domestic sewage
Unilift AP50
Unilift CC
Unilift KP
Drainage pumps
Drainage pumps
0
0.0
0.5
1.0
1.5
2.0
2.5
8
3.0
10
3.5
12
Q [l/s]
Q [m/h]
H
[m]
18
Unilift AP12
16
Drainage pumps
14
12
10
0
0
2
5
3
10
15
H
[m]
18
6
20
7
25
30
Q [l/s]
Q [m/h]
H
[m]
12
11
10
9
8
7
6
5
4
3
2
1
0
2.5
8
3.0
10
3.5
12
Q [l/s]
Q [m/h]
Unilift AP35/50
Wastewater and
sewage pumps
0
0
2
5
3
10
4
15
6
20
7
25
8
30
10 Q [l/s]
35 Q [m/h]
KPBasic
Drainage pumps
8
7
12
10
AP50B
AP35B
0
0
0
2
5
3
10
4
15
6
20
7
25
8
30
Q [l/s]
Q [m/h]
2.0
Wastewater and
sewage pumps
14
1.5
H
[m]
10
Unilift AP35B/50B
16
1.0
35
0.5
AP
0.0
50
AP
H
[m]
9
1
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
0
10
12
Q [l/s]
14 Q [m/h]
H
[m]
9
Performance range
General data
2. General data
General data
Applications
The Unilift CC, KP and AP are submersible drainage
pumps suitable for temporary as well as permanent
free-standing installation. Furthermore, Unilift AP35B
and AP50B pumps are suitable for installation on an
auto coupling at the bottom of a collecting tank with
guide rails going to the top.
The pumps are designed for intermittent operation.
pH values:
Unilift CC: 4 to 9
Unilift KP: 4 to 9
Unilift AP: 4 to 10.
Maximum density:
1,100 kg/m3.
Maximum installation
depth below water level: 10 m.
For permanent installation, level controllers are
available: LC 107, LC 108 and LC 110 for one-pump
installations and LCD 107, LCD 108 and LCD 110 for
two-pump installations.
Examples of applications
Applications
Max. liquid temperature [C]
Max. particle size [mm]
Non-permanent, light-duty applications (used as a portable pump)
Non-permanent, heavy-duty applications for installers and light industry
(used as a portable pump)
Pumping of:
Water and rainwater in horticulture
Water from rivers and lakes
Rainwater, drainage water and water from flooding
Water for filling/emptying containers, ponds, tanks, etc.
Effluents from showers, washing machines and sinks below sewer
level
Pool water
Ditch drainage water
Groundwater (lowering applications)
Domestic effluents from septic and sludge-treating systems
Liquids containing fibres from light industry, laundries, etc.
Effluents from viaducts, underpasses, etc.
Drainage water from garage sprinkler systems
Domestic wastewater with toilet discharge from pipes and water
closets below sewer level, outdoor pump installations
Domestic wastewater with toilet discharge from pipes and water
closets below sewer level, indoor pump installations
= Recommended pump type
= Alternative pump type
KP
AP12
KPB
AP35
AP35B
AP50
AP50B
40
10
50
10
55
12
40
10
55
35
40
35
55
50
40
50
General data
Wastewater definitions
Type keys
Drainage
Unilift CC pumps
Example
Sewage
Untreated wastewater and raw sewage containing
fibres, textiles and other solids, including toilet discharge from domestic sewage systems, farms and
industry.
To avoid clogging, pumps allowing free passage of
solids up to 70-80 mm are recommended. Be aware
that toilet discharge often contains foreign bodies such
as nappies, tampons, toilet rolls, childrens toys and
toothbrushes.
Pump overview
CC
KP
AP12
KP Basic
AP35
AP35B
AP50
AP50B
A1
Free passage
[mm]
Impeller type
Number of
motor poles
10
10
12
10
35
35
50
50
Semi-open
Semi-open
Semi-open
Semi-open
Vortex
Vortex
Vortex
Vortex
2
2
2
2
2
2
2
2
Unilift KP pumps
Example
Unilift KP
150
Type range
Rated motor output, P2 [W]:
150
250
350
Level control:
S = with integrated, electronic sensor
(automatic operation)
A = with float switch
(automatic operation)
M = without level switch
(manual operation)
Motor:
1 = single-phase
3 = three-phase
Unilift AP pumps
Example
Unilift AP
35
B.
50.
Type range
Maximum solids size [mm]
Pump type:
Blank = AP pump
B
= AP Basic
Nominal diameter of discharge port
Power output P2 /100 [W]
Level control:
A
= Automatic operation (with float switch)
Blank = Manual operation (without float switch)
Motor:
1 = Single-phase
3 = Three-phase
Impeller:
V = Vortex impeller
CC
Type
Effluent
Pump range
Unilift
Unilift
Type range
08.
.V
Construction
Vertical, single-stage, submersible centrifugal pumps
with horizontal or vertical discharge port designed for
free-standing installation, installation by means of an
auto-coupling guide rail system or installation in
collecting tanks.
The pumps are directly connected to an asynchronous
submersible motor for 1 x 230 V + 6/- 10 %, 3 x 230 V
+ 6/- 10 % or 3 x 400 V + 6/- 10 %, 50 Hz.
Enclosure class: IP68
Insulation class: B or F.
2
General data
Unilift pumps
Single-phase pumps incorporate thermal overload
protection and require no additional motor protection.
Three-phase pumps must be connected to a motor
starter.
Installation
The pumps are suitable for free-standing installation.
Unilift AP35B and AP50B can be installed on an autocoupling guide rail system, available as an accessory.
Pumps for vertical dry tank installation can be installed
by means of a stationary stand with suction bend.
Unilift CC
Components included
The pump is supplied with an adapter, a non-return
valve and a 90 bend.
The adapter has 3/4", 1" and 1 1/4" external threads.
It must be cut to fit the discharge pipe.
The non-return valve can be fitted in the adapter to
prevent backflow through the pump when it stops.
The 90 bend has 1 1/4" internal threads and is
intended for use on the side discharge outlet.
TM06 0686 0714
Fig. 1
Unilift CC
Motor
The motor is a single-phase, asynchronous, dry-rotor
motor. The axial rotor position is secured by means of
a ball bearing. The motor is cooled by the pumped
liquid around the motor.
Insulation class
Enclosure class
Unilift CC 5
IP68
Unilift CC 7
IP68
Approvals
Unilift CC 9
IP68
Pumped liquids
The pumps are suitable for these liquids:
clean, non-aggressive water
slightly dirty (grey) wastewater.
The pumps are not suitable for these liquids:
liquids containing long fibres
inflammable liquids (oil, petrol, etc.)
aggressive liquids.
If the pump has been used for other liquids than clean
water, it should be flushed through with clean water
immediately after use.
A special version where all wetted parts are made of
stainless steel, EN 1.4401, and suction strainer of
composite is available for slightly aggressive liquids,
such as salt water or chlorinated water below 20 C.
Selection
Performance curves
H
[m]
Unilift CC
50 Hz
10
-9
9
8
-7
7
6
-5
0
0.0
2
0.5
4
1.0
6
1.5
7
2.0
9
2.5
10
11
12
3.0
13
3.5
14
Q [m/h]
4.0
Q [l/s]
The broken line represents a min. flow velocity of 0.7 m/s with a DN 32 discharge pipe to DIN EN 12056.
Using the side outlet may result in up to 5 % drop in performance.
Operating conditions
Liquid temperature
0 C to +40 C.
However, at intervals of at least 30 minutes, the pump
is allowed to run at maximum +70 C for periods not
exceeding two minutes.
Installation
The pump can be used in the vertical position as well
as in the tilted or horizontal position with the discharge
port as the highest point of the pump. The suction
strainer must be covered by the pumped liquid.
Fig. 2
Start
Stop
Pump positions
Installation depth
Maximum 10 metres below the water surface.
Fig. 3
Pump type
Unilift CC 5
Unilift CC 7
Unilift CC 9
10
Start
[mm]
Stop
[mm]
Start
[mm]
Stop
[mm]
350
350
385
115
115
150
400
400
435
55
55
90
Pump type
Voltage
[V]
P1
[W]
In
[A]
Unilift CC 5
Unilift CC 7
Unilift CC 9
1 x 220/240
1 x 220/240
1 x 220-240
240
380
780
1.1
1.7
3.7
Dimensions [mm]
H
Top discharge
H
Side discharge
Weight
[kg]
520
520
570
350
350
400
400
400
500
4.35
4.6
6.5
133
90
137.5
270
160
238
Fig. 6
TM060739 0814
105
306.6
Fig. 4
Technical data
Pump dimensions
Materials
Standard version
Component
Material
Motor sleeve
Pump sleeve
Impeller
Suction strainer
V-ring
O-rings
PP 15 GF
PP 15 GF
PP 20 GF
Stainless steel, class A2
NBR 50
NBR 70
H05RN-F 3G0.75 (CC 5)
H07RN-F3G1 (CC 7 - CC 9)
Cable
DIN W. - Nr.
1.4301
Special versions
Fig. 5
Component
Material
Motor sleeve
Pump sleeve
Impeller
Suction strainer
V-ring
O-rings
Wetted motor parts
PP 15 GF
PP 15 GF
PP 20 GF
PP 15 GF
NBR 50
NBR 70
Stainless steel, class 2
H05RN-F 3G0.75 (CC 5)
H07RN-F3G1 (CC 7 - CC 9)
Cable
DIN W. - Nr.
1.4401
11
Functions
Unilift KP-A
Fig. 7
Unilift KP-A
Versions
The Unilift KP pump series comes in these versions:
Unilift KP-A
with float switch
(automatic operation)
Unilift KP-AV
with vertical level switch
(automatic operation)
Unilift KP-M
without level switch
(manual operation)
Approvals
CE, LGA, VDE, GS, EMV, GOST, UL, CSA and
C-TICK.
12
Pumped liquids
Unilift KP
Construction
The stainless steel pump sleeve is made in one piece
with Rp 1 1/4 discharge port and insulating handle.
Unilift KP have a watertight vulcanized plug.
Liquid enters the pump through the holes of the
suction strainer. The holes of the strainer prevent the
passage of large solids.
The sturdy impeller has single-curved vanes.
The bevelled front edges prevent fibres from jamming
the impeller.
The guide vanes of the pump housing guide the liquid,
lifting sand grains into the liquid flow. This prevents
sand from blocking the impeller.
Motor
The motor is a single-phase or three-phase,
asynchronous canned motor with liquid-filled rotor
chamber and water-lubricated bearings. The motor is
cooled by the pumped liquid around the motor.
Enclosure class: IP68
Insulation class: F
The motor incorporates automatic overload protection.
In case of overload, the motor stops automatically.
When cooled, the motor restarts automatically.
Selection
13
Operating conditions
Installation depth:
Min. liquid temperature:
Max. liquid temperature at
continuous operation:
*
Level switches
Installation
If Unilift KP is installed in a collecting well, the
minimum well dimensions must be as shown in the
figures below.
Start
Stop
400 mm
350B mm
Fig. 8
Pump type
Cable length
(L)
min. 70 mm
Cable length
(L)
max. 150 mm
Start
[mm]
Stop
[mm]
Start
[mm]
Stop
[mm]
290
140
335
100
300
150
345
110
Unilift KP 150 A
Unilift KP 250 A
Unilift KP 350 A
400 mm
250 mm
Fig. 9
Pump positioning
Unilift KP-M and Unilift KP-A can be used in the
vertical position with the discharge port uppermost or
in the horizontal or tilted position with the discharge
port as the highest point of the pump.
Unilift KP-AV must be used in the vertical position.
100 mm
100mm
mm
110
14
Stop
Stop
Start
Start
80 mm
80
mm
p
[kPa]
H
[m]
80
Unilift KP
KP 350
Performance curves
50 Hz
ISO 9906 Annex A
8
KP 250
7
60
6
KP 150
5
40
4
3
20
2
1
0
0
0
10
12 Q [m/h]
3
Q [l/s]
The broken line shows a minimum flow velocity of 0.7 m/s with a DN 32 discharge pipe to DIN EN 12056.
Supply voltage
[V]
Pump type
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
KP
KP
KP
KP
KP
KP
KP
150
150
250
250
250
350
350
1
1
1
1
3
1
3
x
x
x
x
x
x
x
220-230
230-240
220-230
230-240
380-415
220-240
380-400
Power P1
[W]
Current, I n
[A]
Power factor
[Cos ]
Speed
[min-1]
Capacitor
[F]
300
1.3
0.99
2900
0.97
2900
0.99
2900
DIN W. - Nr.
AISI
1.4301
1.4301
1.4301
1.4301
1.4057
1.4301
1.4301
304
304
304
304
431
304
304
2.3
2.2
0.8
3.2
1.3
480
480 (415 V)
700
Pump dimensions
226
220
Rp 1
Materials
140
Component
Material
Pump sleeve
Pump housing
Suction strainer
Impeller
Shaft
Stator housing
Guide vanes
Bearings
O-rings
Seal rings
Stainless steel
Stainless steel
Stainless steel
Stainless steel
Stainless steel
Stainless steel
Stainless steel
Carbon
NBR
NBR
H07RN-F 3 G 1
H07RN-F 4 G 1
Cables
148
30
15
Unilift AP12
Approvals
VDE, LGA, UL and CSA.
Discharge port
All Unilift AP12 pumps have a threaded vertical
discharge port.
Unilift AP12.40: Rp 1 1/2
Unilift AP12.50: Rp 2.
Impeller
The stainless steel impeller is a semi-open impeller
with L-shaped blades and a clearance of 12 mm.
The blades are curved backwards to reduce any
harmful effect from solid particles and to minimise
power consumption.
16
Automatic operation
Shaft seal
The shaft seal is a combination of a mechanical
bellows shaft seal and a lip seal with 60 ml oil
between. Seal faces are made of silicone carbide.
Motor
The motor is a single- or three-phase asynchronous
dry-rotor motor.
Enclosure class: IP68
Insulation class: F (155 C)
Cable type:
H07RN-F.
Single-phase motors have built-in thermal protection.
Materials
Component
Material
DIN W. - Nr.
AISI
Pump housing
Stainless steel
1.4301
304
Riser pipe
Stainless steel
1.4301
304
Impeller
Stainless steel
1.4301
304
Pump sleeve
Stainless steel
1.4401
316
Pump shaft - wet end Stainless steel
1.4301
304
Bearings
Heavy-duty prelubricated ball bearings
O-rings
NBR rubber
Screws
Stainless steel
1.4301
304
Oil
Shell Ondina 15, non-toxic
17
Selection
18
Performance curves
p
[kPa]
160
120
H
[m]
AP12
16
.50
.11
.3
14
.50
.1
12
.4
0.
08
.4
0
10
80
Dimensional sketch
50 Hz
1.1
.0
6
.4
0.
04
40
0
0
P1
[hp]
10
15
20
25
30
35
Q [m/h]
10
P1
[kW]
Q [l/s]
.50.11.3
2.0
.50.11.1
1.6
.40.08
1.2
.40.06
1
0.8
.40.04
0.4
0
0.0
0
10
15
20
25
Pump type
Voltage
[V]
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
3
3
3
3
1
1
3
3
3
3
1
1
3
3
3
3
1
1
3
3
3
3
AP12.40.04.1
AP12.40.04.A1
AP12.40.04.3
AP12.40.04.A.3
AP12.40.04.3
AP12.40.04.A.3
AP12.40.06.1
AP12.40.06.A.1
AP12.40.06.3
AP12.40.06.A.3
AP12.40.06.3
AP12.40.06.A.3
AP12.40.08.1
AP12.40.08.A.1
AP12.40.08.3
AP12.40.08.A.3
AP12.40.08.3
AP12.40.08.A.3
AP12.50.11.1
AP12.50.11.A.1
AP12.50.11.3
AP12.50.11.A.3
AP12.50.11.3
AP12.50.11.A.3
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
230
230
230
230
400
400
230
230
230
230
400
400
230
230
230
230
400
400
230
230
230
230
400
400
30
35
Q [m/h]
P1
[kW]
P2
[kW]
In
[A]
Cos
0.7
0.7
0.7
0.7
0.7
0.7
0.9
0.9
0.9
0.9
0.9
0.9
1.3
1.3
1.2
1.2
1.2
1.2
1.7
1.7
1.9
1.9
1.9
1.9
0.4
0.4
0.4
0.4
0.4
0.4
0.6
0.6
0.6
0.6
0.6
0.6
0.8
0.8
0.8
0.8
0.8
0.8
1.1
1.1
1.2
1.2
1.2
1.2
3.0
3.0
2.2
2.2
1.2
1.2
4.4
4.4
2.9
2.9
1.6
1.6
5.9
5.9
3.7
3.7
2.1
2.1
8.5
8.5
6.4
6.4
3.2
3.2
0.99
0.99
0.85
0.85
0.83
0.83
0.99
0.99
0.83
0.83
0.83
0.83
0.99
0.99
0.85
0.85
0.87
0.87
0.92
0.92
0.85
0.85
0.88
0.88
I start
Dimensions [mm]
--------In
3.8
3.8
4.7
4.7
5.0
5.0
3.8
3.8
5.4
5.4
4.8
4.8
3.8
3.8
4.7
4.7
4.9
4.9
3.8
3.8
3.6
3.6
4.6
4.6
321
321
321
321
321
321
321
321
321
321
321
321
346
346
346
346
346
346
357
357
357
357
357
357
216
216
216
216
216
216
216
216
216
216
216
216
216
216
216
216
216
216
241
241
241
241
241
241
Weight
[kg]
S
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp 1
Rp
Rp
Rp
Rp
Rp
Rp
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
2
2
2
2
2
2
11.0
11.0
9.7
12.0
9.7
12.0
11.0
11.0
10.7
13.0
10.7
10.7
12.6
12.6
12.0
14.3
12.0
14.3
15.1
15.1
15.6
17.9
15.6
17.9
19
Start
start
Min.
550
min.
550
Two-pump installation
Pump type
Unilift AP12
20
Cable length
min. 100 mm
Min.800
800
min.
Stop
stop
TM03 1896 3305
Min. 600
min.
600
Cable length
max. 350 mm
Start
[mm]
Stop
[mm]
Start
[mm]
Stop
[mm]
500
300
550
100
KP Basic
Constructional features
Pump
Water-resistant technopolymer pump sleeve, impeller
and suction strainer. Stainless steel motor housing,
rotor shaft and screws.
Triple "O" ring seals interposed with oil chamber.
Gr7913
Motor
Fig. 19 KP Basic
KP Basic
DNM connections
Rp 1 1/2
Max. 16
Head H [m]
Max. 10.8
Temperature t [C]
Max. +40
Rain water
Clean wastewater
21
29
1
54
73
78
79 32
Descriptions
Pump sleeve
Materials
Noryl GFN 2
Impeller
Noryl GFN 2
29
O-ring
NBR
32
Stop ring
Motor
54
22
Motor housing
Rotor
78
Pressure disc
Noryl GFN 2
79
Suction strainer
Noryl GFN 2
KP Basic 200
KP Basic 300
KP Basic 600
Selection
23
Performance range
p
[kPa]
H
[m]
KPBasic
10.5
100
10.0
50 Hz
600 (A)
9.5
90
9.0
8.5
80
8.0
7.5
70
7.0
300 A
6.5
60
6.0
200
5.5
50
5.0
4.5
40
4.0
3.5
30
3.0
2.5
20
2.0
1.5
10
1.0
0.0
0
0.0
0.5
1.0
1.5
2.0
Curve conditions
The performance curves are based on the kinematic
viscosity values = 1 mm2/s and density equal to
1000 kg/m3.
Curve tolerance according to ISO 9906, Annex A.
24
2.5
10
11
3.0
12
13
3.5
14
4.0
15
16
4.5
17 Q [m/h]
Q [l/s]
0.5
Technical data
KP Basic 300 A
Operating range:
From 0 C to +35 C
+40 C
8m
KP Basic 200 5 mm
KP Basic 300A 10 mm
KP Basic 600 10 mm
KP Basic 600A 10 mm
KP Basic 200 8 mm
KP Basic 300A 85 mm
KP Basic 600 38 mm
KP Basic 600A 175 mm
7m
1 minute
KP Basic 600 A
Installation:
25
Electrical data
Voltage
[V]
Pump type
KP Basic 200
KP Basic 300A
Start
H2
Stop
H1
H
E
B
1 x 220-240
1 x 220-240
P1
P2
P2
I1/1
Max.
[kW] [hp] [A]
[kW]
350
350
0.22
0.22
0.3
0.3
1.5
1.5
Capacitor
[F]
[Vc]
8
8
450
450
A
D
Pump type
KP Basic 200
KP Basic 300A
Stop
Start
H1
H2
[mm]
[mm]
185
185
140
140
225
225
82
82
266
275
390
390
38.5
47.5
100
100
350
350
DNM
Rp 1 1/4
Rp 1 1/4
L/A
L/B
L/H
Volume
[m3]
Weight
[kg]
207
207
227
227
312
312
0.016
0.016
4.5
4.6
P1
P2
P2
I1/1
Max.
[kW] [hp] [A]
[kW]
800
800
800
Capacitor
[F]
[Vc]
14
14
-
450
450
-
E
B
KP Basic 600
KP Basic 600A
KP Basic 600
Start
H2
Stop
H1
H
Pump type
A
D
26
Dimensions [mm]
A
200
200
160
160
225 90
225 90
H1
H2
Stop
[mm]
376
376
490
490
73
73
200
200
Start
[mm]
DNM
450
450
Rp 1 1/4
Rp 1 1/4
L/B
L/H
Volume
[m3]
Weight
[kg]
207
207
227
227
422
422
0.021
0.021
7
6.7
Unilift AP35
Discharge port
All Unilift AP35 pumps have a threaded Rp 1 1/2
vertical discharge port.
Impeller
The stainless steel impeller is a vortex impeller with
L-shaped blades and a clearance of 35 mm in the
pump housing. The blades are curved backwards to
reduce any harmful effect from solid particles and to
minimise power consumption. The impeller has a
protective cap to prevent the deposit of long-fibred
material.
Approvals
VDE, LGA, UL and CSA.
Automatic operation
The pump is available for automatic as well as manual
operation and can be installed in a permanent
installation or used as a portable pump. The pump is
available in these versions:
with float switch fitted for automatic on/off operation
between two liquid levels (single-phase pumps)
with separate level switch and control box for
automatic on/off operation between two liquid levels
(three-phase pumps)
without level switch for manual on/off operation.
Pumps fitted with float switch can also be used for
manual on/off operation. In this case the float switch
must be secured in an upward-pointing position.
Shaft seal
The shaft seal is a combination of a mechanical,
bellows shaft seal and a lip seal with 60 ml oil
between. Seal faces are made of silicone carbide.
27
3
Technical data and performance curves
28
Motor cable
The motor is a single- or three-phase asynchronous
dry-rotor motor.
Enclosure class: IP68
Insulation class: F (155 C)
Cable type:
H07RN-F.
Single-phase motors have built-in thermal protection.
Materials
Component
Materials
Pump housing
Riser pipe
Impeller
Pump sleeve
Pump shaft - wet end
Bearings
O-rings
Screws
Cables
Oil
Stainless steel
1.4301
304
Stainless steel
1.4301
304
Stainless steel
1.4301
304
Stainless steel
1.4401
316
Stainless steel
1.4301
304
Heavy-duty prelubricated ball bearings
NBR rubber
Stainless steel
1.4301
304
Neoprene
Shell Ondina 15, non-toxic
DIN W. - Nr.
AISI
Selection
29
p
[kPa]
H
[m]
AP
35
.4
11
100
AP35
0.0
8
50 Hz
.V
10
AP
35
80
Dimensional sketch
.40
.0
6.V
8
7
60
40
3
20
Performance curves
2
1
0
0
P1
[hp]
10
12
14
16
18
20
Q [m/h]
6
Q [l/s]
P1
[kW]
AP35.40.08.V
1.2
1.5
1.0
AP35.40.06.V
0.6
0.5
0.4
0.0
0.0
0.2
30
10
12
14
16
Pump type
Voltage
[V]
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
3
3
3
3
1
1
3
3
3
3
AP35.40.06.1.V
AP35.40.06.A.1.V
AP35.40.06.3.V
AP35.40.06.A.3.V
AP35.40.06.3.V
AP35.40.06.A.3.V
AP35.40.08.1.V
AP35.40.08.A.1.V
AP35.40.08.3.V
AP35.40.08.A.3.V
AP35.40.08.3.V
AP35.40.08.A.3.V
x
x
x
x
x
x
x
x
x
x
x
x
230
230
230
230
400
400
230
230
230
230
400
400
18
20
Q [m/h]
1.0
0.8
P1
[kW]
P2
[kW]
In
[A]
Cos
0.9
0.9
0.9
0.9
0.9
0.9
1.2
1.2
1.1
1.1
1.1
1.1
0.6
0.6
0.6
0.6
0.6
0.6
0.7
0.7
0.7
0.7
0.7
0.7
4.0
4.0
3.0
3.0
1.6
1.6
5.5
5.5
3.6
3.6
2.0
2.0
0.97
0.97
0.85
0.85
0.83
0.83
0.98
0.98
0.85
0.85
0.86
0.86
I start
Dimensions [mm]
--------In
4.1
4.1
5.2
5.2
4.8
4.8
4.0
4.0
5.3
5.3
5.1
5.1
376
376
376
376
376
376
410
410
410
410
410
410
216
216
216
216
216
216
216
216
216
216
216
216
Weight
[kg]
S
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
1
1
1
1
1
1
1
1
1
1
1
1
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
1/2
11.4
11.4
11.1
13.4
11.1
13.4
12.7
12.7
12.1
14.4
12.1
14.4
Start
start
Min.550
550
min.
Two-pump installation
Pump type
Unilift AP35
Cable length
min. 100 mm
Min.800
800
min.
Stop
stop
TM03 1897 3305
Min. 600
min.
600
Cable length
max. 350 mm
Start
[mm]
Stop
[mm]
Start
[mm]
Stop
[mm]
500
300
550
100
31
Pump housing
Pump housing with an outstanding design for
submersible wastewater pumps, resulting in a high
head.
The pump housing is made of a steel tube with a
smooth surface and a hydraulically correct shape
ensuring free passage of particles.
Ring stand, pump inlet and pump housing are fastened
to the motor by means of four springs enabling quick
and easy dismantling.
Discharge port
All Unilift AP35B pumps have a threaded R 2
horizontal discharge port.
Impeller
The stainless steel impeller is a vortex impeller with
L-shaped blades and a clearance of 35 mm in the
pump housing. The blades are curved backwards to
reduce any harmful effect from solid particles and to
minimise power consumption. The impeller has a
protective cap to prevent the deposit of long-fibred
material.
Unilift AP35B
Automatic operation
The pump is available for automatic as well as manual
operation and can be installed in a permanent
installation or used as a portable pump. The pump is
available in these versions:
with float switch fitted for automatic on/off operation
between two liquid levels (single-phase pumps)
without level switch for manual on/off operation.
Pumps fitted with float switch can also be used for
manual on/off operation. In this case, the float switch
must be secured in an upward-pointing position.
32
Shaft seal
The shaft seal is a combination of a mechanical,
bellows shaft seal and a lip seal with 80 ml oil
between. Seal faces are made of silicone carbide.
Motor cable
The motor is a single- or three-phase asynchronous
dry-rotor motor.
Enclosure class: IP68
Insulation class: F (155 C)
Cable type:
H07RN-F.
Single-phase motors have built-in thermal protection.
Materials
Component
Pump housing
Impeller
Washer
Protective cap
Material
DIN W. - Nr.
Stainless steel
1.4301
Stainless steel
1.4301
Stainless steel
1.4301
Novolen 2360 Kx
Parts in contact
Motor unit complete with liquid:
1.4401
Stainless steel
Pump shaft - wet end Stainless steel
1.4301
Motor cable
Neoprene
O-rings
NBR rubber
Spring
Stainless steel
1.4310
Pump inlet
Stainless steel
1.4301
Ring stand
Polycarbonate
Oil
Shell Ondina 15, non-toxic
AISI
304
304
304
316
304
304
33
Selection
34
Performance curves
p
[kPa]
Dimensional sketch
H
[m]
AP35B
13
120
50 Hz
12
AP
35
B.5
0.0
11
100
8.1
10
9
AP
35
B.5
0.0
8
8
7
60
AP
35
B.5
0.0
AP
35
B.5
0
5
40
.3
80
6.3
.06
.1
0
0
10
12
14
16
20
Q [m/h]
P1
P1
[hp] [kW]
1.6
18
Q [l/s]
AP35B.50.08.3
1.2
3
20
AP35B.50.08.1
1.0
AP35B.50.06.3
1.2
AP35B.50.06.1
0.8
0.6
0.4
0.4
0.2
0.0
0.0
0
10
12
14
16
18
20
Q [m/h]
0.8
Pump type
Voltage
[V]
P1
[kW]
P2
[kW]
In
[A]
Cos
C
[F]
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
3
1
1
3
1.0
1.0
1.0
1.25
1.25
1.25
0.66
0.66
0.63
0.71
0.71
0.78
4.4
4.4
1.55
5.44
5.44
1.98
0.98
0.98
0.89
0.98
0.98
0.89
3.1
3.1
5.2
3.4
3.4
5.4
AP35B.50.06.A1.V
AP35B.50.06.1.V
AP35B.50.06.3.V
AP35B.50.08.A1.V
AP35B.50.08.1.V
AP35B.50.08.3.V
x
x
x
x
x
x
230
230
400
230
230
400
I start
---------
Dimensions [mm]
In
13.8
13.8
8.0
18.4
18.4
10.6
443
443
443
468
468
468
116
116
116
116
116
116
73
73
73
73
73
73
S
R
R
R
R
R
R
2
2
2
2
2
2
Weight
[kg]
8.5
8.5
7.4
10.0
10.0
8.4
Start
start
stop
Stop
TM03 1914 3305
Min.600
600
min.
Start/stop level
Min. 550
550
min.
Start
[mm]
Stop
[mm]
633
270
35
C
F
T
E
S
G
K
Pump type
Unilift AP35B.50.06
Unilift AP35B.50.08
600
600
600
600
304
304
135
135
82
82
85
85
65
65
100
100
76
76
150
150
400
400
200
200
300
300
700
700
500
500
R2
R2
3/4"
3/4"
130
130
261
261
36
Dimensions [mm]
A
600
600
600
600
304
304
135
135
82
82
85
85
26
26
100
100
76
76
150
150
400
400
200
200
300
300
700
700
335
35
330
330
R2
R2
3/4"
3/4"
130
130
261
261
Unilift AP50
Discharge port
All Unilift AP50 pumps have a threaded Rp 2 vertical
discharge port.
Impeller
The stainless steel impeller is a vortex impeller with
L-shaped blades and a clearance of 50 mm in the
pump housing. The blades are curved backwards to
reduce any harmful effect from solid particles and to
minimise power consumption. The impeller has a
protective cap to prevent the deposit of long-fibred
material.
Approvals
VDE, LGA, UL and CSA.
Automatic operation
The pump is available for automatic as well as manual
operation and can be installed in a permanent
installation or used as a portable pump. The pump is
available in these versions:
with float switch fitted for automatic on/off operation
between two liquid levels (single-phase pumps)
with separate level switch and control box for
automatic on/off operation between two liquid levels
(three-phase pumps)
without level switch for manual on/off operation.
Pumps fitted with float switch can also be used for
manual on/off operation. In this case, the float switch
must be secured in an upward-pointing position.
Shaft seal
The shaft seal is a combination of a mechanical,
bellows shaft seal and a lip seal with 60 ml oil
between. Seal faces are made of silicone carbide.
37
3
Technical data and performance curves
38
Motor
The motor is a single- or three-phase asynchronous
dry-rotor motor.
Enclosure class: IP68
Insulation class: F (155 C)
Cable type:
H07RN-F.
Single-phase motors have built-in thermal protection.
Materials
Component
Material
Pump housing
Riser pipe
Impeller
Pump sleeve
Pump shaft - wet end
Bearings
O-rings
Screws
Cables
Oil
Stainless steel
1.4301
304
Stainless steel
1.4301
304
Stainless steel
1.4301
304
Stainless steel
1.4401
316
Stainless steel
1.4301
304
Heavy-duty prelubricated ball bearings
NBR rubber
Stainless steel
1.4301
304
Neoprene
Shell Ondina 15, non-toxic
DIN W. - Nr.
AISI
Selection
39
p
[kPa]
H
[m]
AP50
12
AP
50
.5
11
100
Dimensional sketch
AP
10
60
40
0.1
1.3
V
50
.50
.11
.1 V
AP
50
.50
.0
9
80
50 Hz
8.V
3
20
Performance curves
12
16
20
24
28
32
Q [m/h]
10
Q [l/s]
P1
P1
[hp] [kW]
1.6
2
.5
AP50
1V
0.11.
1
.50.1
AP50
AP50.50.08.V
.3V
1.2
0.8
0.4
0.0
0
40
12
16
20
24
Pump type
Voltage
[V]
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
3
3
3
3
1
1
3
3
3
3
AP50.50.08.1.V
AP50.50.08.A.1.V
AP50.50.08.3.V
AP50.50.08.A.3.V
AP50.50.08.3.V
AP50.50.08.A.3.V
AP50.50.11.1.V
AP50.50.11.A.1.V
AP50.50.11.3.V
AP50.50.11.A.3.V
AP50.50.11.3.V
AP50.50.11.A.3.V
x
x
x
x
x
x
x
x
x
x
x
x
230
230
230
230
400
400
230
230
230
230
400
400
28
32
Q [m/h]
P1
[kW]
P2
[kW]
In
[A]
Cos
1.3
1.3
1.2
1.2
1.2
1.2
1.6
1.6
1.6
1.6
1.9
1.9
0.8
0.8
0.8
0.8
0.8
0.8
1.1
1.1
1.2
1.2
1.2
1.2
5.9
5.9
3.3
3.3
2.0
2.0
8.0
8.0
6.0
6.0
3.0
3.0
0.99
0.99
0.85
0.85
0.80
0.80
0.92
0.92
0.85
0.85
0.88
0.88
Dimensions [mm]
I start
--------In
1.9
1.9
2.8
2.8
3.0
3.0
4.0
4.0
2.8
2.8
4.9
4.9
436
436
436
436
436
436
436
436
436
436
436
436
241
241
241
241
241
241
241
241
241
241
241
241
Weight
[kg]
S
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
Rp
2
2
2
2
2
2
2
2
2
2
2
2
15.1
15.1
14.2
16.5
14.2
16.5
15.1
15.1
15.6
17.9
15.6
17.9
Start
start
Min.550
550
min.
Two-pump installation
Pump type
Unilift AP50
Cable length
min. 100 mm
Min. 800
800
min.
Stop
stop
TM03 1897 3305
Min.600
600
min.
Cable length
max. 350 mm
Start
[mm]
Stop
[mm]
Start
[mm]
Stop
[mm]
500
300
550
100
41
Pump housing
Pump housing with an outstanding design for
submersible wastewater pumps resulting in a high
head.
The pump housing is made of a steel tube with a
smooth surface and a hydraulically correct shape
ensuring free passage of particles.
Ring stand, pump inlet and pump housing are fastened
to the motor by means of four springs enabling quick
and easy dismantling.
Discharge port
All Unilift AP50B pumps have a threaded R 2
horizontal discharge port.
Impeller
The stainless steel impeller is a vortex impeller with
L-shaped blades and a clearance of 50 mm in the
pump housing. The blades are curved backwards to
reduce any harmful effect from solid particles and to
minimise power consumption. The impeller has a
protective cap to prevent the deposit of long-fibred
material.
Unilift AP50B
Automatic operation
The pump is available for automatic as well as manual
operation and can be installed in a permanent
installation or used as a portable pump. The pump is
available in these versions:
with float switch fitted for automatic on/off operation
between two liquid levels (single-phase pumps)
without level switch for manual on/off operation.
Pumps fitted with float switches can also be used for
manual on/off operation. In this case, the float switch
must be secured in an upward-pointing position.
42
Shaft seal
The shaft seal is a combination of a mechanical,
bellows shaft seal and a lip seal with 80 ml oil
between. Seal faces are made of silicone carbide.
Motor
The motor is a single- or three-phase asynchronous
dry-rotor motor.
Enclosure class: IP68
Insulation class: F (155 C)
Cable type:
H07RN-F.
Single-phase motors have built-in thermal protection.
Materials
Component
Materials
Pump housing
Impeller
Washer
Protective cap
Stainless steel
1.4301
Stainless steel
1.4301
Stainless steel
1.4301
Novolen 2360 Kx
Parts in contact
with liquid:
1.4401
Stainless steel
Stainless steel
1.4301
Neoprene
NBR rubber
Stainless steel
1.4310
Stainless steel
1.4301
Polycarbonate
Shell Ondina 15, non-toxic
DIN W. - Nr.
AISI
304
304
304
316
304
304
43
Selection
44
Performance curves
p
[kPa]
200
Dimensional sketch
H
[m]
AP50B
20
50 Hz
ISO 9906 Annex A
18
160
16
14
12
80
AP
50
AP
50
B
AP
50
B
40
.50
.50
.08
.08
AP
50
.3
AP
50
.1
B.5
0
B.5
0.1
B.5
0.1
.15
.3
1.3
1.1
12
16
20
24
28
32
Q [m/h]
10
Q [l/s]
P1
P1
[hp] [kW]
10
120
2.4
AP50B.50.15.3
3
2.0
.11.1
AP50B.50
AP50B.50.11.3
1.6
0.08.3
AP50B.5
1
AP50B.50.08.
1.2
1
0.8
0.0
0.4
12
16
20
24
28
32
Q [m/h]
Pump type
Voltage
[V]
P1
[kW]
P2
[kW]
In
[A]
Cos
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
3
1
1
3
3
1.2
1.2
1.25
1.75
1.75
1.75
2.15
0.7
0.7
0.8
1.2
1.2
1.3
1.5
5.37
5.37
1.95
8.00
8.00
2.81
3.00
0.97
0.97
0.89
0.95
0.95
0.90
0.88
AP50B.50.08.A1.V
AP50B.50.08.1.V
AP50B.50.08.3.V
AP50B.50.11.A1.V
AP50B.50.11.1.V
AP50B.50.11.3.V
AP50B.50.15.3.V
x
x
x
x
x
x
x
230
230
400
230
230
400
400
C
[F]
16
16
16
16
I start
---------
Dimensions [mm]
In
18.4
18.4
10.6
23.8
23.8
16.0
22.4
468
468
468
468
468
468
468
116
116
116
116
116
116
116
73
73
73
73
73
73
73
S
R
R
R
R
R
R
R
2
2
2
2
2
2
2
Weight
[kg]
10.1
10.1
8.4
10.2
10.2
9.7
10.0
Start
start
Stop
stop
TM03 1914 3305
Min.600
600
min.
Start/stop level
Min. 550
550
min.
Start
[mm]
Stop
[mm]
633
270
45
C
F
T
E
S
I
TM03 4194 1806
G
K
Dimensions [mm]
A
600
600
600
600
600
600
304
304
304
135
135
135
82
82
82
85
85
85
65
65
65
100
100
100
76
76
76
150
150
150
400
400
400
200
200
200
300
300
300
700
700
700
500
500
500
R2
R2
R2
3/4"
3/4"
3/4"
130
130
130
261
261
261
46
Dimensions [mm]
A
600
600
600
600
600
600
304
304
304
135
135
135
82
82
82
85
85
85
26
26
26
100
100
100
76
76
76
150
150
150
400
400
400
200
200
200
300
300
300
700
700
700
335
335
335
330
330
330
R2
R2
R2
3/4"
3/4"
3/4"
130
130
130
261
261
261
4. Controllers
Level controller
Variants
Control box
Controllers
47
Controllers
Fig. 50 Unilift AP35B/AP50B pumps with LCD level
controller
48
Controllers
Technical data
LC 107
Voltage tolerances
- 15 %/+ 10 % of rated voltage.
Mains frequency
50/60 Hz.
Ambient temperature
During operation: -30 C to +50 C
(must not be exposed to direct sunlight).
In storage: -30 C to +60 C.
Enclosure class
Pump
IP55.
Settable
stop delay
High-level alarm
Start of pump
Stop of pump
Pneumatic tubes
Dimensions
m
150 m
27 8 mm
Pumps
High-level alarm
Start of second pump
Start of pump
Settable
stop delay
Stop of pump
410 mm
LCD 107
49
Technical data
Voltage tolerances
Applications
The LC 108 and LCD 108 can be connected and set to
operation/control in seven different ways:
systems with two float switches
systems with three float switches
systems with four float switches
systems with two electrodes
systems with three electrodes
systems for filling applications
systems for drainage applications.
50
Dimensions
B
Controllers
Type
LC 108, direct-on-line
LCD 108, direct-on-line
LC 108, star-delta
Dimensions [mm]
H
410
278
150
628
445
180
Float switches
ON
OFF
Fig. 55 Principle sketch of float switch contact
Controllers
51
Controllers
Applications
Technical data
Voltage tolerances
- 15 %/+ 10 % of rated voltage.
Mains frequency
50/60 Hz.
Ambient temperature
During operation: -30 C to +50 C
(must not be exposed to direct sunlight).
In stock: -30 C to +60 C.
Enclosure class
IP55.
Outputs for alarm devices
Max. 230 VAC / max. 2 A / min. 10 mA / AC 1.
Supply system earthing
For TN systems and TT systems.
Rated insulation voltage, Ui
4 kV.
Rated impulse withstand voltage, Uimp
4 kV.
EMC (electromagnetic compatibility)
According to EN 50 081-1 and EN 50 082-2.
Dimensions
27 8 mm
52
410 mm
m
150 m
Accessories
5. Accessories
Accessories for Unilift CC, KP, AP pumps
Pump type
Pos.
Accessories
CC
Product
number
Unilift
Union (PVC)
10
Rp 1 1/2 / 2
Rp 2 / 2 1/2
Rp 1 1/2 / 1 1/2
Rp 1 1/2 / 2
Rp 2 / 2
Rp 2 / 2 1/2
1 1/2"
2"
2 1/2"
Rp 1 1/2
Rp 2
Rp 2 1/2
Rp 1 1/2
Rp 2
Rp 2 1/2
Rp 1 1/2
Rp 2
Rp 2 1/2
Rp 1 1/2
Rp 2
Rp 2 1/2
Rp 1 1/2
Rp 2
Rp 2 1/2
Rp 1 1/2
Rp 2
Rp 2 1/2
Rp 1 1/4
Rp 1 1/2
Rp 2/Rp 2
G 1 1/4 x 25
G 1 1/4 x 32
G 1 1/4 x 40
KP
AP12.40 AP12.50
AP35
AP35B
AP50B
AP50
96023831
96023832
96003997
96023834
96023835
96023836
96023837
96023838
96023839
96023840
96023841
96023842
96023843
96023844
96002003
96023846
96023847
96023848
96023849
96023850
96023851
96023852
96023853
96023854
96023855
96023856
96023857
00015220
96003855
96429519
00ID3588
00ID3589
00ID3590
Cast iron
9
7
3
10
7
8
53
GB/DK/D/F/NL
96841806
16
GB/DK/D/F/NL
96841807
1 - 5.0
3.2 - 12.0
6.0 - 23.0
1.0 - 5.0
16
16
35
16
GB/DK/D/F/NL
GB/DK/D/F/NL
GB/DK/D/F/NL
GB/DK/D/F/NL
96841832
96841834
96841835
96841836
3.2 - 12.0
25
GB/DK/D/F/NL
96841837
1 - 5.0
3.2 - 12.0
6.0 - 23.0
16
25
50
1.0 - 5.0
16
3.2 - 12.0
16
6.0 - 23.0
35
1 - 5.0
16
3.2 - 12.0
16
6.0 - 23.0
16
1.0 - 5.0
16
3.2 - 12.0
16
6.0 - 23.0
25
5.5 - 20.0
35
10.0 - 30.0
63
15.5 - 59.0
125
15.5 - 72.0
160
1 - 5.0
16
3.2 - 12.0
25
6.0 - 23.0
50
GB/DK/D/F/NL
GB/DK/D/F/NL
GB/DK/D/F/NL
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
96841841
96841842
96841843
96841844
96841873
96841902
96841847
96841876
96841905
96841854
96841883
96841912
96841855
96841884
96841913
96841856
96841885
96841914
96841858
96841887
96841916
96841859
96841888
96841917
96841863
96841892
96841921
96841867
96841896
96841925
96841869
96841898
96841927
96841870
96841899
96841928
96841871
96841900
96841929
96841872
96841901
96841930
96841935
96841962
96841989
96841938
96841965
96841992
96841940
96841967
96841994
54
16
96841845
96841874
96841903
96841848
96841877
96841906
1.0 - 5.0
3.2 - 12.0
Language of
installation and
operating instructions
Description
Accessories
96841849
96841878
96841907
96841846
96841875
96841904
96841850
96841879
96841908
96841857
96841886
96841915
96841860
96841889
96841918
96841865
96841894
96841923
96841936
96841963
96841990
96841939
96841966
96841993
96841941
96841968
96841995
96841864
96841893
96841922
96841861
96841890
96841919
96841866
96841895
96841924
96841868
96841897
96841926
96841937
96841964
96841991
6.0 - 23.0
60
5.5 - 20.0
50
10.0 - 30.0
63
15.5 - 59.0
125
15.5 - 72.0
160
1 - 5.0
3.2 - 12.0
6.0 - 23.0
1 - 5.0
3.2 - 12.0
6.0 - 23.0
1 - 5.0
16
16
25
16
16
25
16
3.2 - 12.0
25
GB/DK/D
96842069
1 - 5.0
3.2 - 12.0
6.0 - 23.0
16
25
50
GB/DK/D
GB/DK/D
GB/DK/D
96842080
96842087
96842094
40
96841942
96841969
96841996
96841948
96841975
96842002
96841951
96841978
96842005
96841954
96841981
96842008
96841955
96841982
96842009
96841956
96841983
96842010
96841957
96841984
96842011
96842054
96842056
96842060
96842061
96842064
96842066
96842067
3.2 - 12.0
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/D/PL/NL
GB/GR/I/F/E
GB/DK/S/RU
GB/DK/D
GB/DK/D
GB/DK/D
GB/DK/D
GB/DK/D
GB/DK/D
GB/DK/D
25
1 - 5.0
Language of
installation and
operating instructions
Description
96841943
96841970
96841997
96841949
96841976
96842003
96841952
96841979
96842006
96841944
96841971
96841998
96841945
96841972
96841999
96841950
96841977
96842004
96841953
96841980
96842007
Accessories
55
Accessories
Product no.
Battery back-up
Flashing light for external alarm indication
Alarm horn for external alarm indication (outdoor
installation)
Alarm horn for external alarm indication (indoor
installation)
Hour counter [230 V]
Hour counter [400 V]
Start counter [230 V]
Start counter [400 V]
Combined hour and start counter [230 V]
Combined hour and start counter [400 V]
25 [A] external mains switch for supply cable
40 [A] external mains switch for supply cable
80 [A] external mains switch for supply cable
Bracket for electrodes
Three electrodes with 10 m cable
Four electrodes with 10 m cable
96002520
62500020
62500021
62500022
96002514
96002515
96002516
96002517
96002518
96002519
96002511
96002512
96002513
91713196
96076489
91713437
SMS module
The LC, LCD controllers can be equipped with an SMS
module. An SMS module integrated in an LC, LCD
controller acts as a time recorder for the pumps.
When it has been programmed (using an ordinary
mobile phone with text messaging facility), it can send
text messages containing "high-water alarm", "general
alarm", information about operating hours and the
number of starts.
The SMS module is available with battery enabling it to
send text messages that will inform you of power
failure and when power has been restored.
The LC, LCD controller functions independently - both
before and after integration of the SMS module.
The SMS module is primarily intended as a monitoring
unit or alarm transmitter. Thus, the operator will
receive a text message in the event of an emergency
mode in the system and will be able to retrieve
operating information.
Description
SMS module (GB*)
SMS module (DK*)
SMS module (D*)
SMS module (F*)
SMS module (ES*)
SMS module (RU*)
Antenna for SMS module
Battery for SMS module
SMS module kit complete
SMS module kit complete
SMS module kit complete
SMS module kit complete
SMS module kit complete
SMS module kit complete
*
56
Product no.
(GB*)
(DK*)
(D*)
(F*)
(ES*)
(RU*)
96805159
96805158
96805160
96805161
96805172
96805173
96805155
96805157
96805179
96805177
96805182
96805183
96805184
96805185
Product range
6. Product range
Unilift CC
1 x 220-240 V
Plug type
Pump type
Product number
Schuko
96280965
96280966
96280971
96280972
96280977
96280978
96280967
96280968
96280973
96280974
96280979
96280980
96280969
96280970
96280975
96280976
96280981
96280982
Unilift CC 5
Unilift CC 7
Unilift CC 9
Australia
Float switch
Without
float
switch
Without
plug
With float
switch
Cable type
H05RN-F 3G0.75 H07RN-F 3G1
4.35
Net
weight
[kg]
4.6
6.5
Special versions
Plug type
Pump type
Unilift CC 5
Unilift CC 7
Unilift CC 9
Product
number
Schuko
98624419
98624463
98624464
98624465
98624466
Wetted
parts
EN 1.4401
Float switch
Without
float
switch
With float
switch
Cable type
H05RN-F 3G0.75 H07RN-F 3G1
4m
cable
10 m
cable
Net
weight
[kg]
4.37
5.15
4.55
57
Product range
Unilift KP 150
1 x 220-230 V
Pump type
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
Float switch
Vertical level
switch
5 m cable
10 m cable
With plug
Plug type
Product no.
Schuko
Schuko
Schuko
Schuko
Schuko
Denmark
Denmark
Denmark
Denmark
Denmark
Switzerland
Switzerland
Switzerland
Switzerland
Switzerland
Italy
Italy
Italy
Italy
011H1300
011H1600
011H1400
011H1800
011H1900
011H2300
011H2600
011H2400
011H2800
011H2900
011H3300
011H3600
011H3400
011H3800
011H3900
011H5300
011H5600
011H5400
011H5800
011H6300
011H6600
011H6400
011H6800
011H6900
Product no.
1 x 230-240 V
Pump type
KP 150
KP 150
KP 150
58
Float switch
Vertical level
switch
5 m cable
10 m cable
With plug
Plug type
Australia
Australia
Australia
011K4100
011K4700
011K4500
KP 150
KP 150
KP 150
Unilift KP 250
1 x 220-230 V
Pump type
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
250
Float switch
Vertical level
switch
5 m cable
10 m cable
With plug
Plug type
Product no.
Schuko
Schuko
Schuko
Schuko
Schuko
Denmark
Denmark
Denmark
Denmark
Denmark
Switzerland
Switzerland
Switzerland
Switzerland
Switzerland
Italy
Italy
Italy
Italy
012H1300
012H1600
012H1400
012H1800
012H1900
012H2300
012H2600
012H2400
012H2800
012H2900
012H3300
012H3600
012H3400
012H3800
012H3900
012H5300
012H5600
012H5400
012H5800
012H6300
012H6600
012H6400
012H6800
012H6900
Product range
1 x 230-240 V
Pump type
KP 250
KP 250
KP 250
Float switch
Vertical level
switch
5 m cable
With plug
Plug type
Product no.
Australia
Australia
Australia
012K4100
012K4700
012K4500
3 x 380-415 V
Pump type
Unilift
Unilift
Unilift
Unilift
KP
KP
KP
KP
250
250
250
250
5 m cable
10 m cable
Product no.
012M6100
012M6300
012M9100
012M9300
59
Product range
Unilift KP 350
1 x 220-240 V
Pump type
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
KP
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
350
Float switch
Vertical level
switch
5 m cable
Schuko
Schuko
Schuko
Schuko
Schuko
Denmark
Denmark
Denmark
Denmark
Denmark
Switzerland
Switzerland
Switzerland
Switzerland
Switzerland
Australia
Australia
Australia
013N1300
013N1600
013N1400
013N1800
013N1900
013N2300
013N2600
013N2400
013N2800
013N2900
013N3300
013N3400
013N3600
013N3800
013N3900
013N6300
013N6600
013N6400
013N6800
013N6900
013N4100
013N4700
013N4500
Product no.
Plug type
With plug
10 m cable
3 x 380-415 V
Pump type
Unilift
Unilift
Unilift
Unilift
60
KP
KP
KP
KP
350
350
350
350
5 m cable
10 m cable
Product no.
013M6100
013M6300
013M9100
013M9300
Unilift AP12
Pump type
Voltage
[V]
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
1
1
1
3
3
3
3
3
3
3
3
1
1
1
1
1
3
3
3
3
3
3
3
1
1
1
1
1
3
3
3
3
3
3
3
1
1
1
1
1
3
3
3
3
3
3
3
AP12.40.04.1
AP12.40.04.1
AP12.40.04.A.1
AP12.40.04.A.1
AP12.40-04.A.1
AP12.40.04.3
AP12.40.04.3
AP12.40.04.3
AP12.40.04.3
AP12.40.04.A.3
AP12.40.04.A.3
AP12.40.04.A.3
AP12.40.04.A.3
AP12.40.06.1
AP12.40.06.1
AP12.40.06.A.1
AP12.40.06.A.1
AP12.40.06.A.1
AP12.40.06.3
AP12.40.06.3
AP12.40.06.3
AP12.40.06.A.3
AP12.40.06.A.3
AP12.40.06.A.3
AP12.40.06.A.3
AP12.40.08.1
AP12.40.08.1
AP12.40.08.A.1
AP12.40.08.A.1
AP12.04.08.A.1
AP12.40.08.3
AP12.40.08.3
AP12.40.08.3
AP12.40.08.A.3
AP12.40.08.A.3
AP12.40.08.A.3
AP12.40.08.A.3
AP12.50.11.1
AP12.50.11.1
AP12.50.11.A.1
AP12.50.11.A.1
AP12.50.11.A.1
AP12.50.11.3
AP12.50.11.3
AP12.50.11.3
AP12.50.11.A.3
AP12.50.11.A.3
AP12.50.11.A.3
AP12.50.11.A.3
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
230
230
230
230
230
400
400
230
200
400
400
230
200
230
230
230
230
230
400
230
200
400
400
230
200
230
230
230
230
230
400
230
200
400
400
230
200
230
230
230
230
230
400
230
200
400
400
230
200
Float switch
10 m cable
5 m cable
With plug
Product no.
96011016
96011014
96011017
96011015
96011018
96011024
96023925
96011030
96011021
96011025
96023871
96011031
96011039
96001720
96001732
96001735
96010979
96001747
96001652
96010628
96010881
96010923
96023872
96010957
96010922
96001873
96001869
96001798
96010980
96001867
96001791
96010630
96010882
96010925
96023873
96010958
96010924
96001958
96001962
96001965
96001973
96010981
96001975
96010634
96010883
96010927
96023874
96010959
96010926
Product range
61
Product range
Unilift AP35
Pump type
Voltage
[V]
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
1
1
1
3
3
3
3
3
3
3
1
1
1
1
1
3
3
3
3
3
3
3
AP35.40.06.1.V
AP35.40.06.1.V
AP35.40.06.A.1.V
AP35.40.06.A.1.V
AP35.40.06.A.1.V
AP35.40.06.3.V
AP35.40.06.3.V
AP35.40.06.3.V
AP35.40.06.A.3.V
AP35.40.06.A.3.V
AP35.40.06.A.3.V
AP35.40.06.A.3.V
AP35.40.08.1.V
AP35.40.08.1.V
AP35.40.08.A.1.V
AP35.40.08.A.1.V
AP35.40.08.A.1.V
AP35.40.08.3.V
AP35.40.08.3.V
AP35.40.08.3.V
AP35.40.08.A.3.V
AP35.40.08.A.3.V
AP35.40.08.A.3.V
AP35.40.08.A.3.V
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
230
230
230
230
230
400
230
200
400
400
230
200
230
230
230
230
230
400
230
200
400
400
230
200
Control box
with 0.8 m
supply cable
Float switch
10 m cable
5 m cable
96001796
96001808
96001777
96001789
96010982
96000169
96010629
96010884
96010929
96023875
96010960
96010928
96001672
96001894
96001897
96001905
96010983
96001718
96010631
96010885
96010931
96023876
96010961
96010930
Product no.
With plug
Unilift AP35B
62
Pump type
Voltage
[V]
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
3
1
1
3
AP35B.50.06.A1.V
AP35B.50.06.1.V
AP35B.50.06.3.V
AP35B.50.08.A1.V
AP35B.50.08.1.V
AP35B.50.08.3.V
x
x
x
x
x
x
230
230
400
230
230
400
Float switch
10 m cable
5 m cable
With plug
Product no.
96004562
96004563
96004565
96004574
96004575
96004577
Unilift AP50
Pump type
Voltage
[V]
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
1
1
1
3
3
3
3
3
3
3
1
1
1
1
1
3
3
3
3
3
3
3
AP50.50.08.1.V
AP50.50.08.1.V
AP50.50.08.A.1.V
AP50.50.08.A.1.V
AP50.50.08.A.1.V
AP50.50.08.3.V
AP50.50.08.3.V
AP50.50.08.3.V
AP50.50.08.A.3.V
AP50.50.08.A.3.V
AP50.50.08.A.3.V
AP50.50.08.A.3.V
AP50.50.11.1.V
AP50.50.11.1.V
AP50.50.11.A.1.V
AP50.50.11.A.1.V
AP50.50.11.A.1.V
AP50.50.11.3.V
AP50.50.11.3.V
AP50.50.11.3.V
AP50.50.11.A.3.V
AP50.50.11.A.3.V
AP50.50.11.A.3.V
AP50.50.11.A.3.V
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
230
230
230
230
230
400
230
200
400
400
230
200
230
230
230
230
230
400
230
200
400
400
230
200
Control box
with 0.8 m
supply cable
Float switch
10 m cable
5 m cable
Product no.
96010595
96010599
96010584
96010984
96010592
96010563
96010632
96010886
96010933
96023877
96010962
96010932
96010577
96010581
96010566
96010985
96010574
96010562
96010633
96010887
96010935
96023878
96010963
96010934
With plug
Product range
Unilift AP50B
Pump type
Voltage
[V]
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
Unilift
1
1
3
1
1
3
3
AP50B.50.08.A1.V
AP50B.50.08.1.V
AP50B.50.08.3.V
AP50B.50.11.A1.V
AP50B.50.11.1.V
AP50B.50.11.3.V
AP50B.50.15.3.V
x
x
x
x
x
x
x
230
230
400
230
230
400
400
Float switch
10 m cable
5 m cable
With plug
Product no.
96004586
96004587
96004589
96004598
96004599
96004601
96004609
63
Product range
KP Basic
Voltage
Pump type
KP Basic 200
KP Basic 300A
KP Basic 600
KP Basic 600A
64
Product number
1 x 220-240V,
50 Hz
96121845
96121906
96150042
96825872
96827883
96121846
96121907
96150016
96150043
96825873
96825876
96827886
96827889
96827891
96827903
97657635
96121848
96121849
96121909
96150045
96827888
96121847
96121908
96150017
96150044
96825874
96825877
96827887
96827890
96827902
96827905
Plug type
Schuko
Special model
Australia
China
Indonesia
Cable type
H05RN-F 3G0.75 H07RN-F 3G1
Net
weight
[kg]
4.5
4.6
6.7
7.0
Catalogue
Based on fields of application and pump types, this section
contains the following:
technical data
curves (QH, Eta, P1, P2, etc.) which can be adapted to the
density and viscosity of the pumped liquid and show the
number of pumps in operation
product photos
dimensional drawings
wiring diagrams
quotation texts, etc.
Literature
This section contains all the latest documents of a given pump,
such as
data booklets
installation and operating instructions
service documentation, such as Service kit catalogue and
Service kit instructions
quick guides
product brochures.
Service
This section contains an easy-to-use interactive service
catalogue. Here you can find and identify service parts of both
existing and discontinued Grundfos pumps.
Furthermore, the section contains service videos showing you
how to replace service parts.
65
Sizing
Replacement
In this section you find a guide to selecting and comparing
replacement data of an installed pump in order to replace the
pump with a more efficient Grundfos pump.
The section contains replacement data of a wide range of pumps
produced by other manufacturers than Grundfos.
Based on an easy step-by-step guide, you can compare
Grundfos pumps with the one you have installed on your site.
When you have specified the installed pump, the guide will
suggest a number of Grundfos pumps which can improve both
comfort and efficiency.
CAD drawings
In this section, it is possible to download 2-dimensional (2D) and
3-dimensional (3D) CAD drawings of most Grundfos pumps.
These formats are available in WebCAPS:
2-dimensional drawings:
.dxf, wireframe drawings
.dwg, wireframe drawings.
3-dimensional drawings:
.dwg, wireframe drawings (without surfaces)
.stp, solid drawings (with surfaces)
.eprt, E-drawings.
WinCAPS
WinCAPS is a Windows-based Computer Aided
Product Selection program containing detailed
information on more than 220,000 Grundfos products
in more than 30 languages.
The program contains the same features and
functions as WebCAPS, but is an ideal solution if no
internet connection is available.
WinCAPS is available on DVD and updated once a
year.
Fig. 60 WinCAPS DVD
66
GO CAPS
Mobile solution for professionals on the GO!
CAPS functionality on the mobile
workplace.
Subject to alterations.
67
ECM: 1132516
GRUNDFOS A/S
DK-8850 Bjerringbro . Denmark
Telephone: +45 87 50 14 00
www.grundfos.com
The name Grundfos, the Grundfos logo, and be think innovate are registered trademarks owned by Grundfos Holding A/S or Grundfos A/S, Denmark. All rights reserved worldwide.
96604141 0314
Copyright Grundfos Holding A/S