Beruflich Dokumente
Kultur Dokumente
RoHS
Product Brief
Description
Key Applications
General lighting
Architectural lighting
LED Bulbs
Decorative / Pathway lighting
Color
Min.
Typ.
Max.
Warm White
2600K
3000K
3700K
www.seoulsemicon.com
Table of Contents
Index
Product Brief
Table of Contents
Performance Characteristics
Packaging Information
Company Information
www.seoulsemicon.com
Performance Characteristics
Table 2. Characteristics, IF=20mA, Tj=25C
Value
Parameter
Symbol
Unit
Min.
Typ.
Max.
v[2]
136
155
lm
CCT
2600
3700
CRI[4]
Ra
80
Forward Voltage
VF
60
63
68
Power Dissipation
PD
1.26
Viewing Angle
21/2
120
deg.
Thermal resistance (J to S)
Rj-s
6.0
K/W
ESD Sensitivity(HBM)
5k
Luminous Flux[1]
Correlated Color
Temperature[3]
VF [V]
Power [W]
v [lm]
lm/W
10
60.3
0.60
80.2
133.7
20 (Typ.)
63.8
1.28
150.2
117.3
30
66.7
2.00
212.5
106.3
40
69.3
2.77
269.3
97.2
50
71.6
3.58
321.4
89.8
60
73.6
4.42
369.7
83.6
Symbol
Value
Unit
Forward Current
IF
60
mA
Power Dissipation
PD
4.5
Junction Temperature
Tj
125
Operating Temperature
Topr
-30 ~ + 100
Storage Temperature
Tstg
-40 ~ + 100
Notes :
(1) Seoul Semiconductor maintains a tolerance of 7% on flux and power measurements.
(2) V is the total luminous flux output as measured with an integrating sphere.
(3) Correlated Color Temperature is derived from the CIE 1931 Chromaticity diagram. Color
coordinate : 0.01, CCT 5% tolerance.
(4) Tolerance is 2.0 on CRI measurements.
All measurements were made under the standardized environment of Seoul Semiconductor.
3
www.seoulsemicon.com
1.2
1.0
0.8
0.6
0.4
0.2
0.0
400
500
600
700
800
Wavelength(nm)
1.2
1.0
0.8
0.6
0.4
0.2
0.0
-90
-60
-30
30
60
90
Angle [deg.]
4
www.seoulsemicon.com
60
50
40
30
20
10
0
0
10
20
30
40
50
60
70
80
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
10
20
30
40
50
60
70
www.seoulsemicon.com
Preliminary Specification
Product Data Sheet
SAW8LH0A Acrich MJT 5050
0.402
30mA
10mA
40mA
0.400
CIE Y
20mA
50mA
60mA
0.398
0.396
0.394
0.424
0.426
0.428
0.430
0.432
CIE X
www.seoulsemicon.com
1.0
0.8
0.6
0.4
0.2
0.0
0
25
50
75
100
125
150
o
Junction Temperature [ C]
1.2
1.0
0.8
0.6
0.4
0.2
0.0
0
25
50
75
100
125
150
o
Junction Temperature [ C]
www.seoulsemicon.com
CIE X
CIE Y
-0.002
-0.004
-0.006
-0.008
-0.010
-0.012
0
25
50
75
100
o
Junction Temperature [ C]
125
150
www.seoulsemicon.com
0.06
0.05
0.04
0.03
0.02
Rth(J-a) = 15 'C/W
Rth(J-a) = 20 'C/W
Rth(J-a) = 25 'C/W
0.01
0.00
0
25
50
75
100
125
Ambient Temperature ( C)
www.seoulsemicon.com
V2
136.0~154.0
W1
154.0~177.0
W2
177.0~200.0
Available ranks
Not yet available ranks
Example
BIN CODE : W1G0A
Color bin
3. Voltage Bins
Example
BIN CODE : W1G0A
Voltage bin
Bin Code
Voltage [V]
60.0 - 63.0
63.0 65.0
65.0 68.0
10
www.seoulsemicon.com
0.44
0.42
G0
CIE y
F1
0.40
G3
F3
H4
G5
H3
H2
G2
F0
H1
H0
G1
H5
G4
F2
F5
0.38
F4
0.36
0.38
0.40
0.42
0.44
0.46
0.48
CIE x
F0
CIE x
0.3996
0.3960
0.4104
0.4146
F1
CIE y
0.4015
0.3907
0.3978
0.4089
CIE x
0.4146
0.4104
0.4248
0.4299
CIE y
0.3978
0.3865
0.3931
0.4048
CIE x
0.3925
0.3889
0.4017
0.4062
CIE y
0.4165
0.4048
0.4093
0.4212
CIE x
0.4430
0.4374
0.4499
0.4562
CIE y
0.4093
0.3973
0.4015
0.4138
CIE x
0.4198
0.4147
0.4259
0.4317
CIE y
0.4260
0.4138
0.4166
0.4289
CIE x
0.4687
0.4620
0.4740
0.4810
CIE y
0.4166
0.4042
0.4069
0.4194
CIE x
0.4436
0.4373
0.4483
0.4551
F3
CIE x
0.4104
0.4062
0.4198
0.4248
CIE y
0.4212
0.4093
0.4138
0.4260
CIE x
0.4248
0.4198
0.4317
0.4374
CIE y
0.3931
0.3814
0.3853
0.3973
CIE x
0.4317
0.4259
0.4373
0.4436
CIE y
0.4289
0.4166
0.4194
0.4319
CIE x
0.4499
0.4436
0.4551
0.4620
CIE y
0.4015
0.3893
0.3919
0.4042
CIE x
0.4551
0.4483
0.4593
0.4666
CIE y
0.3865
0.3751
0.3814
0.3931
G2
CIE y
0.4048
0.3931
0.3973
0.4093
G5
CIE y
0.3973
0.3853
0.3893
0.4015
H2
H4
11
CIE y
0.3907
0.3798
0.3865
0.3978
F5
H1
H3
CIE x
0.4620
0.4551
0.4666
0.4740
CIE x
0.4062
0.4017
0.4147
0.4198
G4
H0
CIE x
0.4562
0.4499
0.4620
0.4687
CIE y
0.3798
0.3690
0.3751
0.3865
G1
G3
CIE x
0.4374
0.4317
0.4436
0.4499
CIE x
0.3960
0.3925
0.4062
0.4104
F4
G0
CIE x
0.4299
0.4248
0.4374
0.4430
F2
CIE y
0.4089
0.3978
0.4048
0.4165
CIE y
0.4138
0.4015
0.4042
0.4166
H5
CIE y
0.4042
0.3919
0.3944
0.4069
www.seoulsemicon.com
Mechanical Dimensions
< Top View >
Cathode
Anode
Anode
Notes :
(1)
(2)
(3)
(4)
12
www.seoulsemicon.com
Notes :
(1) Quantity : 7 inch reel type ( 1,000 pcs / Reel )
(2) Cumulative Tolerance : Cumulative Tolerance/10 pitches to be 0.2mm
(3) Adhesion Strength of Cover Tape : Adhesion strength to be 0.1-0.7N when the cover tape is
turned off from the carrier tape at the angle of 10 to the carrier tape
(4) Package : P/N, Manufacturing data Code No. and quantity to be indicated on a damp proof Package.
13
www.seoulsemicon.com
Aluminum Bag
Outer Box
14
www.seoulsemicon.com
Product Nomenclature
Part Number Form : X1X2X3X4X5X6X7X8 X9X10X11X12X13
Part Number
Code
Description
Part Number
Value
X1
Company
SSC
X2
Package series
X3
W
Color
White
X4
X5
Series number
X6
Voltage
X7
PCB type
Emitter
X8
Revision No.
Rev0
X9X10
Luminous flux
X11X12
Color bin
X13
Voltage
LF
V2
L series
Color bin
136.0~154.0
Voltage
A
60.0 ~ 63.0
63.0 ~ 65.0
65.0 ~ 68.0
F0~F5
W1
154.0~177.0
W2
177.0~200.0
G0~G5
H0~H5
15
www.seoulsemicon.com
Notes :
(1)
(2)
(3)
(4)
16
www.seoulsemicon.com
IPC/JEDEC J-STD-020
Table 5.
Profile Feature
Pb-Free Assembly
3 C/second max.
3 C/second max.
Preheat
- Temperature Min (Tsmin)
- Temperature Max (Tsmax)
- Time (Tsmin to Tsmax)
100 C
150 C
60-120 seconds
150 C
200 C
60-180 seconds
183 C
60-150 seconds
217 C
60-150 seconds
215
260
10-30 seconds
20-40 seconds
Ramp-down Rate
6 C/second max.
6 C/second max.
6 minutes max.
8 minutes max.
Caution
(1) Reflow soldering is recommended not to be done more than two times.
In the case of more than 24 hours passed soldering after first, LEDs will be damaged.
(2) Repairs should not be done after the LEDs have been soldered. When repair is unavoidable,
suitable tools must be used.
(3) Die slug is to be soldered.
(4) When soldering, do not put stress on the LEDs during heating.
(5) After soldering, do not warp the circuit board.
17
www.seoulsemicon.com
(2) In general, LEDs should only be handled from the side. By the way, this also applies to
LEDs without a silicone sealant, since the surface can also become scratched.
(3) When populating boards in SMT production, there are basically no restrictions regarding the form
of the pick and place nozzle, except that mechanical pressure on the surface of the resin must be
prevented. This is assured by choosing a pick and place nozzle which is larger than the LEDs
reflector area.
(4) Silicone differs from materials conventionally used for the manufacturing of LEDs. These
conditions must be considered during the handling of such devices. Compared to standard
encapsulants, silicone is generally softer, and the surface is more likely to attract dust. As
mentioned previously, the increased sensitivity to dust requires special care during processing. In
cases where a minimal level of dirt and dust particles cannot be guaranteed, a suitable cleaning
solution must be applied to the surface after the soldering of components.
(5) SSC suggests using isopropyl alcohol for cleaning. In case other solvents are used, it must be
assured that these solvents do not dissolve the package or resin. Ultrasonic cleaning is not
recommended. Ultrasonic cleaning may cause damage to the LED.
(6) Please do not mold this product into another resin (epoxy, urethane, etc) and do not handle this
product with acid or sulfur material in sealed space.
(7) Avoid leaving fingerprints on silicone resin parts.
18
www.seoulsemicon.com
(3) Do not apply mechanical force or excess vibration during the cooling process to normal
temperature after soldering.
(5) Components should not be mounted on warped (non coplanar) portion of PCB.
(6) Radioactive exposure is not considered for the products listed here in.
(7) Gallium arsenide is used in some of the products listed in this publication. These products are
dangerous if they are burned or shredded in the process of disposal. It is also dangerous to drink the
liquid or inhale the gas generated by such products when chemically disposed of.
(8) This device should not be used in any type of fluid such as water, oil, organic solvent and etc.
When washing is required, IPA (Isopropyl Alcohol) should be used.
(9) When the LEDs are in operation the maximum current should be decided after measuring the
package temperature.
(10) LEDs must be stored properly to maintain the device. If the LEDs are stored for 3 months or
more after being shipped from Seoul Semiconductor. A sealed container with a nitrogen atmosphere
should be used for storage.
(11) The appearance and specifications of the product may be modified for improvement without
notice.
(12) Long time exposure of sunlight or occasional UV exposure will cause lens discoloration.
19
www.seoulsemicon.com
(16) The driving circuit must be designed to allow forward voltage only when it is ON or OFF. If the
reverse voltage is applied to LED, migration can be generated resulting in LED damage.
(17) LEDs are sensitive to Electro-Static Discharge (ESD) and Electrical Over Stress (EOS). Below is
a list of suggestions that Seoul Semiconductor purposes to minimize these effects.
a. ESD (Electro Static Discharge)
Electrostatic discharge (ESD) is the defined as the release of static electricity when two objects come
into contact. While most ESD events are considered harmless, it can be an expensive problem in
many industrial environments during production and storage. The damage from ESD to an LEDs may
cause the product to demonstrate unusual characteristics such as:
- Increase in reverse leakage current lowered turn-on voltage
- Abnormal emissions from the LED at low current
The following recommendations are suggested to help minimize the potential for an ESD event.
One or more recommended work area suggestions:
- Ionizing fan setup
- ESD table/shelf mat made of conductive materials
- ESD safe storage containers
One or more personnel suggestion options:
- Antistatic wrist-strap
- Antistatic material shoes
- Antistatic clothes
Environmental controls:
- Humidity control (ESD gets worse in a dry environment)
20
www.seoulsemicon.com
21
www.seoulsemicon.com
Company Information
Published by
Seoul Semiconductor 2013 All Rights Reserved.
Company Information
Seoul Semiconductor (www.SeoulSemicon.com) manufacturers and packages a wide
selection of light emitting diodes (LEDs) for the automotive, general illumination/lighting,
Home appliance, signage and back lighting markets. The company is the worlds fifth
largest LED supplier, holding more than 10,000 patents globally, while offering a wide range
of LED technology and production capacity in areas such as nPola, "Acrich", the worlds
first commercially produced AC LED, and "Acrich MJT - Multi-Junction Technology" a
proprietary family of high-voltage LEDs.
The companys broad product portfolio includes a wide array of package and device choices
such as Acrich and Acirch2, high-brightness LEDs, mid-power LEDs, side-view LEDs, and
through-hole type LEDs as well as custom modules, displays, and sensors.
Legal Disclaimer
Information in this document is provided in connection with Seoul Semiconductor products.
With respect to any examples or hints given herein, any typical values stated herein and/or
any information regarding the application of the device, Seoul Semiconductor hereby
disclaims any and all warranties and liabilities of any kind, including without limitation,
warranties of non-infringement of intellectual property rights of any third party. The
appearance and specifications of the product can be changed to improve the quality and/or
performance without notice.
22
www.seoulsemicon.com