Beruflich Dokumente
Kultur Dokumente
FECHA: 27/02/2015
MANUFACTURA
AVANZADA
Main Menu
Create
Rectangle
2 Points
Press [Enter]
Enter the coordinates. X4,Y4
Press [Enter]
Choose the Fit button to center the geometry
10
11
9. Choose.
OK
OK
10. The Figure will look like this.
12
13
7. Press [Esc] to exit the Backplot Menu. The drawing looks like this.
Verify program
1. Choose the verify button.
14
2.
3.
4.
5.
Pick the button Configure. Choose the Use Job Setup Values button.
Choose OK.
Choose the machine button from the Verify toolbar.
The picture should look like this.
15
16
3. Choose.
OK
Save
Save
4. The NC editor will open a picture like this.
18
3. Choose OK.
4. Click on every line till you get something like this.
19
20
6.
7.
8.
9.
Choose OK.
Choose the Gview (Isometric)
Choose the Fit button.
Save the drawing.
Toolpath creation
Define the rough stock
1. Press [Alt+J].
2. Enter values shown.
21
22
23
8. Choose OK.
Check the program by backplotting
1. Choose
Main Menu
Toolpaths
Operations
Backplot
24
2. Choose Run
25
5. Choose Ok
6. Choose the Machine button.
26
5. Choose OK.
6. Choose Ok in the pocket parameters dialog box. The operations Manager Displays.
7. Choose Regen Path
27
28
3. Choose
OK
Save
Save
4. The NC file will be displayed a larger dialog box.
29
30
3. Choose OK
31
8. Choose
True type
Arial Unicode
OK
9.
10.
11.
12.
32
Main Menu
Toolpaths
Job Setup
2. Enter the values.
3. Move the stock origin arrow as it shows.
4. Choose OK.
Chain the Pocket
1. Choose
2. Click on the upper left corner of the rectangle as shown in the following image.
34
3. Choose
Mode
Window
4. Draw a window around the letters. Keep the window inside the rectangle.
5. Select a point inside one of the letters.
6. Choose Done.
35
4. Choose OK
5. Enter the next values.
36
8. Choose OK
9. The Picture looks like this.
37
3. Choose Done.
38
3. Choose OK
Check the program by Backplotting
1. Choose
Operations
Select All
39
Backplot
2. Choose run.
40
41
3. Choose
OK
Save
Save
42
5. Pen Holder
Geometry creation
Create a rectangle
1. Choose
o Main Menu
o Create
o Rectangle
o 1 Point
2. Enter the values.
43
3. Choose
o OK
o Origin
o Trim
o 2 entities
2. With the cursor, select the two inside lines.
3. Select the remaining 3 lines to trim.
4. Press [Esc]
Create a rectangle for the pocket
1. Choose
o Main Menu
o Xform
o Offset
2. Enter the values
46
3. Choose OK
4. Select the left line of the inside triangle to offset. Move your mouse to the center
of the rectangle and click again. Repeat on the lower line and the right line of the
inner rectangle.
5. Choose
o Backup
o Offset
6. Enter 1.0 as the offset distance in the dialog box
7. Choose OK
8. Select the bottom inside line to offset, clicking on a point near the center of the line.
47
3. Create the first fillet by selecting two interesting lines as shown in the diagram at
right.
4. Create the remaining 3 fillets by selecting the intersecting lines in the other three
corners of the rectangle just created. Your drawing should look like the next picture.
Main Menu
Xform
Translate
49
3. Choose
o Done
o Rectang
4. Enter the translation vector. Z-0.75
5. Enter the values shown
6. Choose OK
7. Choose the Gview (Isometric) button from toolbar
50
2. Choose the fit button from toolbar to fit the geometry in the graphics below.
3. Choose
o Main menu
51
o Create
o Point
o Position
4. Enter coordinates.
X0.375, Y2.625
5. Enter coordinates.
X5.625, Y2.625
53
Toolpath creation
Define the rough stock
1. Choose
2. Enter the values shown
3. Move the arrow from the center of the box in the Job setup dialog box by clicking
and releasing your mouse in the left corner of the stock.
4. Choose OK.
5. It should look like this.
54
Select parameters
1. Right click in the tool display area.
2. Choose Get tool from the library.
3. Select the 1/8 spherical endmill (ball)
55
56
7. Choose OK.
57
58
7. Choose OK.
59
60
5. Choose OK
61
62
8. Choose Ok
63
4. Choose OK
5. Choose the Machine button from the verify toolbar.
6. Close the verify toolbar.
64
3. Choose
o Ok
o Save
65
66
5. Choose OK
67
4. Choose Verify
68
6. Save File
69