Beruflich Dokumente
Kultur Dokumente
1 Volt
12 Volt
1.5 Volt
0.5 Volt
6- You are measuring a current leak of 2 Ampere. (All consumers are switched
of). How long will take until the 40 Ah battery is completely empty? (M2)
a- 10 hours
b- 20 hours
c- 40 hours
7- Three 300 Ohm resistors have been connected parallel the replacement
resistor is? (M2)
a- 900 Ohm
b- 100 Ohm
c- 400 Ohm
8- You have connected two 60Wbubls to a 12V 60Ah battery. How long will the
bulbs light until the battery is completely empty? (M2)
a- hours
b- 4 hours
c- 12 hours
10How does the track voltage at an airflow sensor behave when the load
increases? (M3)
a- The voltage rises
b- The voltage drops
c- The voltage stays stable
11-
12-
14You are measuring a signal voltage of 1.6 Volt at an HFM air mass sensor.
Which statement is correct? (M3)
a- The engine is running by idle
b- The engine is running with full-load
x
2
15-
When does the brake system warning lamp light up? (M4)
a- After switching on ignition until self-check is completed
b- During foot brake operation
c- Change of brake fluid is overdue
16Which information in ABS control unit is, amongst other items processed
further? (M4)
a- Engine temperature
b- Speed sensor signals
c- Engine Speed
17Is the ABS system equipped with a load dependant brake pressure
regulator on the rear axle? (M4)
a- The function of the load dependant brake pressure regulator is undertaken
electronically by the EBD and therefore a brake pressure regulator is not
required
b- Yes
c- A vehicle with ABS requires no brake pressure regulation on the rear axle.
18-
19-
a- All items of information are sent over no more than two wires
b- A separate wire is required for each item of information
21-
20-
x
3
integrated system
c- Each individual control unit must be regarded as being separate
23The vehicle threatens to oversteer. (M4)
How does the ESP system re-stabilize the vehicle?
a- Only by braking the front wheel on the inside of the corner
b- Only by braking the front wheel on the outside of the corner
c- By braking the front wheel on the outside of the corner and by intervening in
the engine and gearbox management systems
d- By braking the front wheel on the inside of the corner and by intervening in
the engine and gearbox management system
26-
29The engine control unit is supplied with the engine speed signal by the
(M3)
a- Engine speed sender
b- Hall sender in the distributor
x
4
32-
How does the engine control unit recognize the first cylinder? (M3)
a- By means of a TDC sensor at the crankshaft
b- By means of the engine speed sensor of the flywheel
c- By means of four hall windows at the hall sender in the distributor , the hall
window of cylinder 1 being larger than those of cylinders 2, 3 and 4
33What are the advantages offered by the new plastic intake manifold?
(M3)
a- Weight savings
b- More compact design
c- Noise reduction
34-
35How do you find information regarding the test mode of the dash panel
insert? (M2)
a- In the electrical system workshop manual
b- In the fault finding binder
c- In the current flow Diagrams or in fault finding programs
36-
I have to programme an additional key and what do I need for this? (M2)
a- The mechanical key code
b- The ident number
c- The secret number
37The engine control unit of a new car has been replaced. Is there any
particular procedure which I must follow in this case? (M3)
5
39The air mass measured in the 1.9 liters TDL engine is required by the
EDC control unit for (M3)
a- Metering the quantity of fuel injected
b- Metering the quantity of exhaust gas recirculated when full load is required
40What statements regarding the auxiliary intake air heater are correct?
(M3)
a- The auxiliary heater is activated each time the engine is started
b- The auxiliary heater is activated from a certain coolant temperature on
c- The auxiliary heater Is activated by the signal of the intake manifold
temperature sensor at the moment the engine started
41The three principal influencing parameters for the fully electronic control
by the EDC engine management system are: (M3)
a- Intake air temperature; air flow manifold temperature
b- Engine Speed, accelerate positive ; air mass
c- Accelerator pedal position, outside temperature, engine speed