Beruflich Dokumente
Kultur Dokumente
1
III B.Tech I Semester Supplimentary Examinations, February 2008
LINEAR IC APPLICATIONS
(Electronics & Communication Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
2. (a) Draw and explain the operation of a current to voltage converter. If 741 IC is
used, what is the lowest value of current that can be measured?
(b) Draw the fundamental log-amp circuit and derive the output voltage expres-
sion. [8+8]
Figure 3a
(b) Distinguish between astable, bistable and monostable multivibrators. [8+8]
4. (a) Design a second order low pass filter for a cutoff frequency of KHz.
(b) Draw the frequency response of the network in the above filter. [8+8]
5. (a) With necessary external components to a VCO IC NE556, Explain the gener-
ation of a triangular wave.
(b) Determine the component values for a control voltage Vc =9 volts and a fre-
quency of oscillation=10KHz. Make necessary assumptions. [10+6]
6. (a) Draw the functional schematic of 555 timer and describe in detail how this IC
can be used to realize a monostable multivibrator.
(b) Draw the pin diagram of 555 timer IC. [12+4]
7. (a) Explain the operation of a multiplying DAC and mention its applications.
1 of 2
Code No: RR310404 Set No. 1
(b) A 12-bit D to A converter has a full-scale range of 15 volts. Its maximum
differential linearity error is ± 1/2 LSB.
i. What is the percentage resolution?
ii. What are the minimum and maximum possible values of the increment in
its output voltage? [8+8]
8. (a) Define the terms ‘Aperture time’ and ‘Droop rate’ of a Sample & Hold circuit.
(b) With a neat circuit diagram explain the operation of an OP-AMP based Sam-
ple & Hold circuit.
(c) Indicate one monolithic Sample & Hold IC of any manufacturer. [4+8+4]
⋆⋆⋆⋆⋆
2 of 2
Code No: RR310404 Set No. 2
III B.Tech I Semester Supplimentary Examinations, February 2008
LINEAR IC APPLICATIONS
(Electronics & Communication Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1 of 2
Code No: RR310404 Set No. 2
8. (a) Explain the operation of an 8-bit tracking type Analog to Digital converter.
(b) Compare the conversion times and efficiencies of 8-bit tracking type and suc-
cessive approximation type Analog to Digital converters. [8+8]
⋆⋆⋆⋆⋆
2 of 2
Code No: RR310404 Set No. 3
III B.Tech I Semester Supplimentary Examinations, February 2008
LINEAR IC APPLICATIONS
(Electronics & Communication Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. (a) An op-amp has a slew rate of 2V/µs. What is the maximum frequency of an
output sinusoid of peak value 5V at which the distortion sets in due to the
slew rate limitation.
(b) If the sinusoid of 10V peak is specified, what is the full power band width?
[8+8]
2. (a) Explain the effect of frequency on the behavior of the virtual ground in an
inverting configuration of an op-amp.
(b) Mention some applications of an instrumentation amplifier. [8+8]
3. (a) Design a non-inverting comparator with output levels stabilizes at ±5V and
VT L = 0 and VT H = 2.5V (TL: Lower threshold, TH: upper threshold) as shown
in the figure3b
(b) For the given inverting Schmitt trigger, calculate its higher and lower trigger
levels. [8+8]
Figure 3b
4. Draw and explain the working principle of first order high pass filter. Derive the
expressions for gain and phase angle of the above filter. [16]
5. (a) With suitable circuit diagram, explain in detail the operation of a saw tooth
wave generator.
(b) List an application of sawtooth waveform.
(c) What are the differences between a saw tooth waveform and a triangular
waveform? [8+4+4]
6. (a) Describe two methods to achieve 50% duty cycle in 555 timer astable multi-
vibrator.
(b) Explain the realization of Schmitt trigger using a 555 timer IC. [8+8]
1 of 2
Code No: RR310404 Set No. 3
7. (a) Sketch and explain the transfer characteristic of a DAC with necessary equa-
tions.
(b) LSB of a 9-bit DAC is represented by 19.6 m Volts. If an input of 9 zero bits
is represented by 0 volts.
i. Find the output of the DAC for an input, 10110 1101 and 01101 1011
ii. What is the Full scale Reading (FSR) of this DAC? [8+8]
8. (a) Explain the requirement of a Sample & Hold circuit in an Analog to Digital
converter.
(b) Explain the operation of a counter type Analog to Digital converter
(c) An 8-bit counter type ADC is driven by a 500 KHz clock. Find the maximum
conversion time of this Analog to Digital converter. [4+8+4]
⋆⋆⋆⋆⋆
2 of 2
Code No: RR310404 Set No. 4
III B.Tech I Semester Supplimentary Examinations, February 2008
LINEAR IC APPLICATIONS
(Electronics & Communication Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. (a) An op-amp has a slew rate of 2V/µs. What is the maximum frequency of an
output sinusoid of peak value 5V at which the distortion sets in due to the
slew rate limitation.
(b) If the sinusoid of 10V peak is specified, what is the full power band width?
[8+8]
2. (a) Draw the circuit of a typical instrumentation amplifier. Why do we use two
stage op-amp circuit as an instrumentation amplifier. Explain
(b) List out the advantages of instrumentation amplifier. [10+6]
3. (a) Discuss important characteristics of a comparator and the limitations of op-
amps as comparators.
(b) Explain the operation of Schmitt trigger circuit. [8+8]
4. (a) In a Low pass filter to active - 3dB frequency of 1KHz with a dc gain of 20dB
and an input resistance of at least 10kΩ, specify the suitable components to
achieve the required specifications.
(b) Draw the ideal and practical frequency response curves of Low pass filter, High
pass filter, Band pass filter and Band rejection filter. [8+8]
5. (a) For a square wave generator with the component values listed below, design an
integrator circuit to convert the square wave to a triangular wave. Negative
feedback resistor = 10KΩ, capacitor = 0.05µF , positive feedback resistor
=11.6KΩ, input resistor at + terminal = 10KΩ Assume IC µA 741 with ±15
volt power supplies.
(b) What is the requirement for the positive feedback resistance to be a poten-
tiometer?
(c) What are the difficulties in obtaining high frequencies of oscillation with such
square wave generators? [6+4+6]
6. (a) What are the difficulties in achieving 50% duty cycle in the basic 555 timer
astable multivibrator?
(b) Indicate one method to overcome this difficulty to achieve 50% duty cycle.
(c) Design a 555 timer astable multivibrator operating at 18 KHz with 40% duty
cycle. [6+4+6]
7. (a) Describe any two applications of NE565 PLL IC with relevant Circuit dia-
grams.
1 of 2
Code No: RR310404 Set No. 4
(b) List important specifications and characteristics of a monolithic Digital to
Analog converter IC MC1408. [12+4]
8. (a) Define the terms, ‘Resolution’, ‘Linearity’ and ‘Conversion time’ of an Analog
to Digital converter.
(b) Describe in detail the operation of a dual slope Analog to digital converter.
[6+10]
⋆⋆⋆⋆⋆
2 of 2