Beruflich Dokumente
Kultur Dokumente
Date: 2/4/2011
Table of Contents
Section I
Section II
Section III
Diagnostic Aids
Firmware Upgrades.........................................8
Factory Mode...................................................9
SMART2011-LCD116 Rev.1
Page 1 of 9
40SL412U
P803
CN1
CN1
P802
CN3
CN2
CN4
P801
CN5
SMART2011-LCD116 Rev.1
Page 2 of 9
40SL412U
Interconnect
P803
LED Supply to Driver PCB
1. VLED 24V
2. VLED 24V
3. VLED 24V
4. VLED 24V
5. VLED 24V
6. BL Gnd
7. BL Gnd
8. BL Gnd
9. BL Gnd
10. BL Gnd
11. NC
12. BL On 3.26V
13. NC
14. PWM (Dimming) .7-3.2V
P
8
0
2
LVDS
C
N
3
CN1
Speakers
Pins 18 TO 21
CN1
120uf
63v X 4
Power Supply
LED
Driver
PCB + = 35V X 4
+ +
C
9
5
C
9
2
C
9
1
C
9
4
C
N
2
LED Supply
P801
C
N IR
4
Touch
Panel
AC In
Main
SMART2011-LCD116 Rev.1
Page 3 of 9
DEAD SET
Dead Set
(No Sound and
No Picture or No
power LED)
Yes
Yes
Yes
Suspect a
problem with the
Main module.
Does
The 12 volt
source appear at
pins 8 and 9 of CN2
when the on/off
button is
pressed?
Does
a 3.3 volt on/off
signal appear at
pin 13 of CN2 on the main
module when the on/off
button is
pressed?
Is
5 VDC present
at pins 11 and 12 of CN2
on the main module when
AC is
applied?
No
No
No
Suspect a
problem with
the power supply
module.
No
Does
a 4.9 volt AC
detect signal appear at
pin 14 of CN2 on the main
module when AC is
applied?
Yes
Suspect a problem
with the SYSCON
circuit located on the
Main module.
SMART2011-LCD116 Rev.1
Page 4 of 9
NO VIDEO
Examples
No or distorted
video
Replace
the LCD display
panel. ***
YES
NO
Use backlight
troubleshooting
flowchart.
Does
the back light function
normally when the unit
is turned on?
YES
Is
the screen
discolored or does it
have streaks and dark
areas on the
screen?
NO
YES
Replace
the Main
Module.
When
the input button
is pressed on the
receiver or remote, is
the on screen
display clear and
normal?
YES
NO
Are the 12
volt sources present
at pins 8 and 9 of CN2
on the main
module?
NO
Suspect the
power supply
module.
Page 5 of 9
No backlight
operation.
NO
NO
Suspect the
main module.
Does the
backlight on signal (3.26v)
appear at pin 16 of CN2 on
the Main PCB shortly after the
unit is powered on?
BACKLIGHT
TROUBLESHOOTING
Does
the back light on
signal (3.26v) appear
at pin 12 of P803 on the
Power PCB shortly after the
unit is
powered
on?
YES
NO
YES
Is 24
volts present
at pins 1-5 of P803,
on the power
PCB?
Suspect the
power supply
module.
YES
Replace the
LCD display
panel.
SMART2011-LCD116 Rev.1
Page 6 of 9
NO AUDIO
No Audio
NO
NO
YES
Problem
solved.
Does
upgrading the
firmware restore
audio?
Is audio missing
on all sources?
NO
YES
Replace the
Main module
Using
the remote or
the manual keyboard,
access the menu to assure
the input selection is a known
good source.
Will this restore
audio?
YES
Problem
solved.
YES
Does
the
power supply
generate both
supply voltages on the
main PCB (12 VDC
at pins 8 and 9 and 24V at
pins 3 and 4) of CN2)
when the unit is
turned
on?
NO
Replace the
power supply
module.
SMART2011-LCD116 Rev.1
Page 7 of 9
Notice(ReadPriortoBeginningtheSoftwareUpgrade)
The following events may interrupt the upgrade process and result in an inoperative unit.
1) DO NOT unplug the Power Cord during the software update procedure.
2) Avoid loss or interruption of power during the software update procedure.
3) DO NOT Press the power button on the unit during the software update procedure.
If you are experiencing problems or have further questions:
Customers should contact Toshiba Customer Service at 800-631-3811.
Toshiba Authorized Service Providers should contact Toshiba Technical Support Group.
UsethefollowingproceduretoupdatetheTelevisionsoftwareversion:
1) Place the TV receiver in the On position (any Channel or input is ok).
2) Insert a USB Flash Drive with firmware copied to the drive into the rear side port marked USB
just below HDMI-3 input.
3) After a few seconds the update screen will appear as shown in Figure 1. Use the left and right
arrow buttons of the remote to highlight the Yes selection. See Figure 2.
4) Press the Enter button to begin the firmware update. A status screen will display as shown in
Figure 3. DO NOT POWER OFF OR PRESS ANY KEY ON THE REMOTE CONTROL UNTIL AFTER COMPLETION OF THE
UPDATE!!! DO NOT REMOVE USB FLASH DRIVE UNTIL INSTRUCTED IN STEP 6!!!
Figure1Figure2
Figure3Figure4
5) The firmware update is complete when the display shows a Success screen as shown in Figure 4.
6) Remove the USB Flash Drive from the TV receiver. Momentarily remove AC power from the set by
unplugging the AC power cord. Firmware updating is now complete. Plug TV back into AC power.
TOSHIBA AMERICA INFORMATION SYSTEMS INC.
1420-B Toshiba Dr.
Lebanon, TN 37087
www7.toshiba.com
SMART2011-LCD116 Rev.1
Page 8 of 9
Factory Mode
The factory mode, necessary adjustments, and update procedures shown below can be
accessed in this unit using the supplied remote control transmitter.
To enter the factory mode, you must press Left Arrow (<), then Exit, then
Enter within approximately two seconds. To end this function, press exit or simply
turn the television off.
Notice the addition of a Touch Key Pad Adjust feature in this model. This is for
the purpose of adjusting the power LED intensity. It must be accessed in the
Factory Mode as indicated above.
SMART2011-LCD116 Rev.1
Page 9 of 9