Beruflich Dokumente
Kultur Dokumente
Air Cylinder
When the job calls for reliable, heavy-duty
performance, specify Series 2A. A 100,000 psi
yield strength chrome-plated, case-hardened
piston rod. A 125,000 psi yield strength rod-end
stud with rolled threads. 100,000 psi yield
strength tie rods. With construction like this, the
Parker Series 2A is rated for air service to 250
psi. This is one heavy-duty air cylinder that's
really heavy duty.
They're truly premium quality cylinders, factory
prelubricated for millions of maintenance-free
cycles. And to make sure every cylinder is
premium quality, we subject each and every one
– not just batch samples – to tough inspection
and performance tests. See pages 18 and 19 for
the inside story on all the features that make
Series 2A the high performance, long lasting
choice for all your heavy-duty air applications.
16
Series 2A Specifications/
Heavy Duty Air Cylinders Mountings
Standard Specifications
• Heavy Duty Service – ANSI/(NFPA) T3.6.7R2-1996 • Piston Rod Diameter – 1/2" through 51/2"
Specifications and Mounting Dimension Standards • Mounting Styles – 17 standard styles at various application
• Standard Construction – Square Head – Tie Rod Design ratings
• Nominal Pressure – Up to 250 PSI Air Service • Strokes – Available in any practical stroke length
• Standard Fluid – Filtered Air • Cushions – Optional at either end or both ends of stroke.
• Standard Temperature – -10°F. to +165°F. "Float Check" at cap end.
• Bore Sizes – 1" through 14" (Larger sizes available) • Rod Ends – Three Standard Choices – Specials to Order
*See section C, “Operating Fluids and Temperature Range” for higher temperature
In line with our policy of continuing product improvement, specifications in this catalog are
subject to change. service.
Note: Series 2A Air Cylinders fully meet ANSI/(NFPA) T3.6.7R2-1996 Specifications and Mounting Dimension Standards for Square Head Industrial Fluid Power Cylinders. A
Parker Style TB, JB, HB, C, DB, and BB are available in 7" bore size, see page 32.
17
The inside story on why Steel Head – Bored and grooved
18
Piston Rod – Medium carbon steel, induction case-hardened to 54 The exclusive
Rc, hard chrome-plated and polished to 10 RMS finish. Piston rods are
made from 90,000 to 100,000 psi minimum yield material in 1/2" through “Jewel” gland
4" diameters. Larger diameters vary between 57,000 and 90,000 psi
minimum material, depending on rod diameter. The piston thread equals gives you longer
the catalog style #4 rod end thread for each rod diameter to assure
proper piston-to-rod thread strength. Two wrench flats are provided for
cylinder life, better
rod end attachment. performance and
Ports – NPTF ports
are standard. lower costs.
An extra-long inboard bearing surface insures lubrication
Steel Cap – Bored and grooved from within the cylinder. Outboard of the bearing surface
to provide concentricity for
mating parts.
are two leakproof seals – The Lipseal and Wiperseal. The
serrated Lipseal (primary seal) is completely self-compen-
sating and self-relieving. It adjusts to mechanical deflec-
A
tions or any pressure variation from near-zero to rated
Alloy Steel Tie Rod Nuts operating pressure. The result is positive, no-leak sealing –
regardless of conditions.
The Wiperseal does double duty. On the advance stroke, it
acts as a secondary pressure seal. On the return, it wipes
away any dirt on the rod. This means less wear on bearing
surfaces and internal parts. Longer life for working parts.
And, less loss of fluid. Plus, you can replace a “Jewel”
Align-A-Groove – gland without removing the tie rods or the retainer. Just a
(Patent #3043639) – A 3/16" wide few twists with a spanner wrench does the job.
surface machined at each end of
the cylinder body. Makes precise Prelubricated Wearing Surfaces
mounting quick and easy.
Parker Series 2A Air Cylinders are factory prelubricated.
One-Piece Nodular Iron Lube-A-Cyl applied to seals, piston, cylinder bore, piston
Piston – The wide piston
surface contacting cylinder bore rod and gland surfaces provides lubrication for normal
reduces bearing loads. operation. Lube-A-Cyl has been field and laboratory
Anaerobic adhesive is used to tested, and is recommended by Parker for air cylinders
permanently lock and seal the where lubricant should remain in the cylinder and not be
piston to the rod. expelled into the atmosphere.
Piston Lipseal – Fully dynamic
and self-compensating for
Piston with Retainer Nut –
variations in pressure, mechani- Optional at extra charge.
cal deflections and wear.
Cushion Length
Cushion Length Cushion Length
Cylinder Rod (Inches) Cylinder Rod (Inches)
Bore Diameter* Rod Bore Diameter* Rod
(Inches) (Inches) Number Head* Cap (Inches) (Inches) Number Head* Cap
5/8 1 7/8 13/16 13/8 1 13/8 11/4
11/2 6
1 2 7/8 13/16 4 2 11/16 11/4
5/8 1 7/8 13/16 13/8 1 11/16 11/4
2 7
13/8 2 7/8 13/16 2 4 11/16 11/4
5/8 1 7/8 13/16 13/8 1 11/16 11/4
21/2 8
13/4 2 7/8 13/16 51/2 2 15/16 11/4
1 1 11/8 1 13/4 1 1 5/16 13/4
31/4 10
2 2 13/16 1 51/2 0 13/16 13/4
1 1 11/8 1 2 1 1 5/16 13/4
4 12
21/2 2 13/16 1 51/2 9 1 3/16 13/4
1 1 11/8 1 21/2 1 13/4 2
5 14
31/2 2 13/16 1 51/2 8 111/16 2
*Head end cushions for rod diameters not listed have cushion lengths with the limits shown.
For cushion selection and sizing see Section C.
19
Tie Rod and
Rectangular Flange Mountings
Series 2A
1" to 6" Bore Sizes Heavy Duty Air Cylinders
Basic Mounting (T) — ZB + STROKE
Tie Rods Extended NFPA MX0 — no tie rods extended can be supplied upon Y P + STROKE
Style TB request. W LB + STROKE
E
(NFPA Style MX3) EE
1
AA
E 4 2 R MM
DD
3 G J K
BB F
R
Style TB (NFPA MX3). Head Tie Rods Extended, illustrated: Style TC (NFPA MX2), Cap Tie Rods Extended; and Style
TD (NFPA MX1), Both Ends Tie Rods Extended are also available. All “T” styles can be dimensioned from Style TB
drawing at right.
E 4 2 R MM
3 G J K
F
E FB
4 HOLES WF
TF
MM R 2 4 E
K 3
F G J F
E FB
XF 4 HOLES
TF
20
Series 2A Tie Rod and
Rectangular Flange Mountings
Heavy Duty Air Cylinders 1" to 6" Bore Sizes
21
Square Flange Mountings
Series 2A
1" to 6" Bore Sizes Heavy Duty Air Cylinders
Head Square Flange
Style JB
(NFPA Style MF5)
UF ZB + STROKE
E Y P + STROKE
1 W LB + STROKE
EE
UF E 4 2 R TF MM
F G J K
3
FB
R WF
8 HOLES
TF
MM TF R 2 4 E UF
F G J F 3
XF FB
R
8 HOLES
TF
22
Series 2A Square Flange Mountings
Heavy Duty Air Cylinders 1" to 6" Bore Sizes
23
Side Lugs, Centerline Lugs
and Side Tapped Mountings
Series 2A
1" to 6" Bore Sizes Heavy Duty Air Cylinders
Side Lug ZB + STROKE
Style C Y P + STROKE
W LB + STROKE
(NFPA Style MS2) US
EE
1
E 4 2 MM
E –.005
2 –.010
ST
3 G J K
SB F
SW E SW 4 HOLES SW SU SU SW
SW TS SW
XS SS + STROKE
Style E Y P + STROKE
LB + STROKE
W
(NFPA Style MS3) US
EE
1 SB
4 HOLES
ST
E MM
4 2
3 G J K
F
SW E SW SW SU SU SW
SW TS SW
XS SS + STROKE
E 4 2 MM
E –.005
2 –.010
3 G J K
F
TN NT THREAD, ND DEEP XT SN + STROKE
4 TAPPED MTG. HOLES
24
Series 2A Side Lugs, Centerline Lugs
and Side Tapped Mountings
Heavy Duty Air Cylinders 1" to 6" Bore Sizes
25
Side End Angles and
Side End Lugs Mountings
Series 2A
1" to 6" Bore Sizes Heavy Duty Air Cylinders
Side End Angles
Style CB
(NFPA Style MS1)
ZA + STROKE
XA + STROKE
Y P + STROKE
W LB + STROKE AB
E 6 HOLES
EE
4
E 3 1 MM S
AT 2 AT
J K
AH AO AL F G AL AO
SA + STROKE
E 4 2 MM
E —.005
2 —.010
ET
3 1 J EO
64 F G
R EB EO EL
4 HOLES EL
ES ES
SE + STROKE
26
Series 2A Side End Angles and
Side End Lugs Mountings
Heavy Duty Air Cylinders 1" to 6" Bore Sizes
27
Trunnion Mountings
Series 2A
1" to 6" Bore Sizes Heavy Duty Air Cylinders
ZB + STROKE
Head Trunnion
Y P + STROKE
Style D W LB + STROKE
(NFPA Style MT1) UT
EE
1
1R
8
E 4 2 TD MM
3 G J K
F
TL E TL
XG
1R
8
E 4 2 TD MM
3 F G J K
TL E TL
XJ + STROKE
1R
8
UV E 4 2 TD MM
3 F G J K
E
XI**
TL TM TL
28
Series 2A Trunnion Mountings
Heavy Duty Air Cylinders 1" to 6" Bore Sizes
2 11/2 21/2 3/8** 3/8 11/2 1 5/16 1.000 1 3 5 41/2 3 4 21/4 1/2
21/2 11/2 3 3/8** 3/8 11/2 1 5/16 1.000 1 31/2 51/2 5 31/2 41/8 23/8 3/8
31/4 2 33/4 1/2 5/8 13/4 11/4 3/8 1.000 1 41/2 61/2 53/4 41/4 47/8 25/8 7/8
4 2 41/2 1/2 5/8 13/4 11/4 3/8 1.000 1 51/4 71/4 61/2 5 47/8 25/8 7/8
5 2 51/2 1/2 5/8 13/4 11/4 7/16 1.000 1 61/4 81/4 71/2 6 51/8 27/8 5/8 A
6 21/2 61/2 3/4 3/4 2 11/2 7/16 1.375 13/8 75/8 103/8 91/4 7 53/4 31/8 11/8
* Cushions not available on 1" bore.
** On 1", 11/2", 2" and 21/2" bore sizes, the head-end (only) pipe thread is not full depth on cylinders
with No. 2 rods. Minimum of three full threads available.
• Mounting style not available in 1" bore.
■1" bore head dimension is 13/4" x 11/2". See page B20.
29
Clevis Mountings
Series 2A
1" to 6" Bore Sizes Heavy Duty Air Cylinders
Cap Fixed Clevis
Style BB
(NFPA Style MP1)
ZC + STROKE PIVOT PIN
Y P + STROKE HARD CHROME PLATED
W LB + STROKE
E
EE
CD 1
MM 2 4 E
MR
LR
K 3
F G J L M
CW CB CW
XC + STROKE
The 1", 4", 5" and 6" bore sizes have tie rod nuts at both ends as shown. Tie rods thread into cap on all other bore sizes.
MM 2 4 E
MR
LR
K 3
F G J F L M
CW CB CW
XD + STROKE
30
Series 2A Clevis Mountings
Heavy Duty Air Cylinders 1" to 6" Bore Sizes
31
Tie Rod, Head Square and Series 2A
Cap Square Mountings
7" Bore Size Heavy Duty Air Cylinders
ZB + STROKE
Style TB (NFPA MX3) Head
Tie Rods Extended Tie Rods Extended,
Y P + STROKE
W LB + STROKE
Style TB illustrated: Style TC (NFPA
MX2), Cap Tie Rods
E EE
1
(NFPA Style MX3) Extended; and Style TD
(NFPA MX1), Both Ends Tie
Rods Extended are also
available. All “T” styles can
be dimensioned from Style
AA
TB drawing at right.
E 4 2 R MM
DD
3
TTSQ. F G J K
R WF
BB
ZB + STROKE
Head Square Flange Y P + STROKE
Style JB E
W LB + STROKE
EE
(NFPA Style ME3) 1
E 4 2 TE MM
3
F G J K
TTSQ. EB
4 HOLES WF
TE
ZJ + STROKE
Cap Square Flange Y P + STROKE
Style HB W LB + STROKE
EE E
(NFPA Style ME4) 1
MM TE 2 4 E
K 3
F G J
TE EB
XK + STROKE 4 HOLES
32
Side Lug, Side Tapped,
Series 2A Cap Trunnion, Head Trunnion,
Cap Fixed Clevis Mountings
Heavy Duty Air Cylinders 7" Bore Size
E 2 MM
4 E 4 2 MM
E —.005
2 —.010 E —.005
2 —.010 A
ST
3
F G J K 3
TTSQ. SB
SW SU SU SW F G J K
SW E SW 4 HOLES TN SN + STROKE
XS SS + STROKE NT THREAD, ND DEEP XT
SW TS SW 4 TAPPED MTG. HOLES
1R 1R
8 8
E 4 2 TD MM E 4 2 TD MM
3 3
F G J K F G J K
TTSQ. TTSQ.
XJ + STROKE XG
TL E TL TL E TL
ZC + STROKE
Cap Fixed Clevis Y P + STROKE
PIVOT PIN
E
W LB + STROKE
Style BB EE
1
(NFPA Style MP1) CD
MM E 2 4
MR
LR
K
3
F G J L M
XC + STROKE CW CB CW
Note: Other mounting styles and double rod end cylinders are available on request. Consult factory for details.
33
Tie Rod, Head Square and Series 2A
Cap Square Mountings
8" to 14" Bore Size Heavy Duty Air Cylinders
ZB + STROKE
Style TB (NFPA MX3)
Tie Rods Extended Head Tie Rods Extended,
Y P + STROKE
W LB + STROKE
Style TB illustrated: Style TC (NFPA
MX2), Cap Tie Rods E EE
1
(NFPA Style MX3) Extended; and Style TD
(NFPA MX1), Both Ends
Tie Rods Extended are
also available. All “T”
styles can be
dimensioned from Style AA
TB drawing at right.
E 4 2 R MM
DD
3
TTSQ. F G J K
Mounting styles TB & TD not offered in R WF
8" bore, rod codes #2, 9 and 0. BB
ZB + STROKE
Head Square Flange Y P + STROKE
W
Style JB E
LB + STROKE
EE
(NFPA Style ME3) 1
E 4 2 TE MM
3
F G J K
TTSQ. EB
4 HOLES WF
TE
ZJ + STROKE
Cap Square Flange Y P + STROKE
Style HB W LB + STROKE
EE E
(NFPA Style ME4) 1
MM TE 2 4 E
K 3
F G J
TE EB
XK + STROKE 4 HOLES
34
Series 2A Tie Rod, Head Square and
Cap Square Mountings
Heavy Duty Air Cylinders 8" to 14" Bore Size
35
Side Lugs and
Centerline Lugs Mountings Series 2A
8" to 14" Bore Size Heavy Duty Air Cylinders
Side Lug
Style C
(NFPA Style MS2)
ZB + STROKE
Y P + STROKE
W LB + STROKE
US EE
1
E 2 MM
4
E —.005
2 —.010
ST
3
F G J K
TTSQ. SB
SW SU SU SW
SW E SW 4 HOLES
XS SS + STROKE
SW TS SW
Centerline Lugs
Style E
(NFPA Style MS3)
ZB + STROKE
Y P + STROKE
W LB + STROKE
US EE
1
SB
4 HOLES
ST
E MM
4 2
3
F G J K
TTSQ.
SW SU SU SW
SW E SW
XS SS + STROKE
SW TS SW
36
Series 2A Side Lugs and
Centerline Lugs Mountings
Heavy Duty Air Cylinders 8" to 14" Bore Sizes
37
Side Tapped and
Side End Lugs Mountings
Series 2A
8" to 14" Bore Size Heavy Duty Air Cylinders
Side Tapped
Style F
(NFPA Style MS4)
ZB + STROKE
Y P + STROKE
E W LB + STROKE
SQ.
TT EE
1
E 4 2 MM
E —.005
2 —.010
3
F G J K
TN XT SN + STROKE
NT THREAD, ND DEEP
4 TAPPED MTG. HOLES
Side End Lugs Cylinders with this mounting style are mounted on the precision ground surfaces of the head and cap. There must
be a minimum gap of at least 1/64 of an inch between the bottom of the lug and the mounting surface before the
Style G mounting bolts are tightened.
(NFPA Style MS7) ZE + STROKE
XE + STROKE
Y P + STROKE
W LB + STROKE
E EE
1 K
E 4 2 MM
E —.005
2 —.010
ET
3
1 F G J
TTSQ. 64 EO EL EL EO
R EB SE + STROKE
4 HOLES
ES ES
Not offered in the following sizes: 8" bore, rod codes #2, 6, 7, 8, 9 and 0; 10" bore,
rod codes #8, 9 and 0; and 12" bore, rod codes #7, 8 and 9.
38
Series 2A Side Tapped and
Side End Lugs Mountings
Heavy Duty Air Cylinders 8" to 14" Bore Sizes
39
Side End Angle and
Clevis Mountings Series 2A
8" to 14" Bore Sizes Heavy Duty Air Cylinders
Side End Angles
Style CB ZA + STROKE
(NFPA Style MS1) XA + STROKE
Y P + STROKE
W LB + STROKE
E EE AT
4 AB 6
HOLES
E 3 1 MM S
2
F G J K
AT TTSQ.
AO AL AL AO
AH
SA + STROKE
Not offered in the following sizes: 8" bore, rod codes #2, 6, 7, 8, 9 and 0; 10"
bore, rod codes #8, 9 and 0.
MM E 2 4
MR
LR
K
3
F G J L M
XC + STROKE CW CB CW
40
Series 2A Side End Angles and
Clevis Mountings
Heavy Duty Air Cylinders 8" to 14" Bore Sizes
41
Trunnion Mountings
Series 2A
8" to 14" Bore Sizes Heavy Duty Air Cylinders
ZB + STROKE
Head Trunnion Y P + STROKE
W
Style D UT
LB + STROKE
EE
(NFPA Style MT1) 1
1R
8
E 4 2 TD MM
3
TTSQ. F G J K
TL E TL XG
ZB + STROKE
Cap Trunnion Y P + STROKE
Style DB W LB + STROKE
UT EE
(NFPA Style MT2) 1
1R
8
E 4 2 TD MM
3
TTSQ. F G J K
TL E TL XJ + STROKE
ZB + STROKE
Intermediate Fixed Trunnion Y P + STROKE
Style DD W LB + STROKE
EE
(NFPA Style MT4) UM
BD
1
1R
8
UV E 4 2 TD MM
3 F G J K
TTSQ. XI**
E
TL TM TL
42
Series 2A Trunnion Mountings
Heavy Duty Air Cylinders 8" to 14" Bore Sizes
10 3 5
10 /8 1 3/4 21/4 2 11/16 1.750 13/4 12 151/2 141/8 113/4 71/8 41/8 7/8
12 3 123/4 1 3/4 21/4 2 11/16 1.750 13/4 14 171/2 161/4 133/4 75/8 45/8 3/8
14 31/2 143/4 11/4 3/4 23/4 21/4 3/4 2.000 2 161/4 201/4 183/4 16 87/8 51/2 3/8
43
Spherical Bearing Mounting Series 2A
Style SB
11/2" to 6" Bore Sizes Heavy Duty Air Cylinders
XL + STROKE
CE ZC + STROKE LUBRICATION
LUBRICATION XC + STROKE MA FITTING
FITTING
1 1
KE
ER
4 2 2 4
MS
CD CD
3 3
LE W NR
EX KK EX
A
44
Series 2A Spherical Bearing Mounting
Style SB
Heavy Duty Air Cylinders 8" to 14" Bore Sizes
XL + STROKE
CE ZC + STROKE LUBRICATION
LUBRICATION XC + STROKE MA FITTING
FITTING
1 1
KE
ER
2 2
4 4
A
MS
CD CD
3 3
LE W NR
EX KK EX
A
45
Double Rod Models
Series 2A
1" to 14" Bore Sizes Heavy Duty Air Cylinders
How to Use Double Rod Cylinder Dimensioned Drawings
1"- 6" Bores ZM + 2 X STROKE
ZL + STROKE
Y P + STROKE
W LD + STROKE
EE
MM
Dimensions Shown on
Mounting This Page Supplement K
Mounting Styles for Dimensions on Pages F G
Listed Below G F
Styles for Corresponding
1"-6" 8"-14"
Single Rod Double Rod Bores Bores 7"- 14" Bores Y
ZM + 2 X STROKE
P + STROKE
Models Models* Page No. Page No. W LD + STROKE
EE
T KT 20 34
TB** KTB 20 34
TD KTD 20 34 Rod End #1 Rod End #2
J KJ 20 — MM
JB** KJB 22 34
C** KC 24 36
E KE 24 36 K
F
G F
F KF 24 38 WF G
CB KCB 26 40 To determine dimensions for a double rod addition to those for single rod cylinders
G KC 26 38 cylinder, first refer to the desired single rod shown on preceding pages and provide the
mounting style cylinder shown on preceding information needed to completely dimension
D KD 28 42 pages of this catalog. (See table at left.) After a double rod cylinder.
DD KDD† 28 42 selecting necessary dimensions from that On a double rod cylinder where the two rod
drawing, return to this page supplement the ends are different, be sure to clearly state
*If only one end of these Double Rod Cylinders is to single rod dimensions with those shown on
be cushioned, be sure to specify clearly which end which rod end is to be assembled at which
this will be. drawings at right and dimension table below. end. Port position 1 is standard. If other than
**Available in 7" bore, page 32. Note that double rod cylinders have a head standard, specify pos. 2, 3 or 4 when viewed
† Specify XI dimension from rod end #1.
(Dim. G) at both ends and that dimension LD from rod end #1 only. See port position
replace LB and ZL replaces ZB, etc. The information in Section C.
double rod dimensions differ from, or are in
All dimensions are in inches and apply to Code 1 rod sizes only. For alternate rod sizes,
determine all envelope dimensions (within LD dim.) as described above and then use
appropriate rod end dimensions for proper rod size from single rod cylinder.
Add 2X
Add Stroke Stroke
Rod
Rod Dia.
Bore No. MM LD ZL SAK XAK ZAK SSK SNK SEK XEK ZEK ZM
1 1 1/2 43/4 51/2 63/8 63/16 61/2 33/8* 21/8 * * * 6
11/2 1 5/8 47/8 53/4 67/8 61/2 67/8 33/8 21/4 63/8 61/4 61/2 6 1/ 8
2 1 5/8 47/8 513/16 67/8 61/2 67/8 33/8 21/4 63/4 67/16 63/4 6 1/ 8
21/2 1 5/8 5 515/16 7 65/8 7 31/2 23/8 71/8 611/16 7 6 1/ 4
31/4 1 1 6 71/8 81/2 8 81/2 33/4 25/8 73/4 75/8 8 71/2
4 1 1 6 71/8 81/2 8 81/2 33/4 25/8 8 73/4 81/8 71/2
5 1 1 61/4 77/16 9 83/8 9 35/8 27/8 83/8 81/16 89/16 73/4
6 1 13/8 7 85/16 93/4 91/4 97/8 41/8 31/8 9 87/8 93/8 83/4
7 1 13/8 71/8 — — — — 41/4 31/4 — — — 87/8
8 1 13/8 71/8 — 91/4 91/16 93/4 41/4 31/4 77/8 83/8 9 87/8
10 1 13/4 81/8 — 107/8 105/8 111/2 47/8 41/8 91/4 913/16 107/16 103/8
12 1 2 85/8 — 113/8 111/4 121/8 53/8 45/8 93/4 107/16 111/16 111/8
14 1 21/2 101/8 — 131/2 135/16 143/8 63/8 51/2 115/8 123/8 131/8 131/8
Replaces: LB ZB SA XA ZA SS SN SE XE ZE —
On single rod
mounting styles: All Mtg. Styles CB C,E F G All Mtgs.
* Mounting styles KE, KG and KDD not available in 1" and 7" bore sizes.
46
Series 2A Cylinder Accessories
Spherical Bearing Mounting
Heavy Duty Air Cylinders Style SB
Parker offers a complete range of Cylinder Accessories respective cylinder include the Rod Eye, Pivot Pin and
to assure you of the greatest versatility in present or Clevis Bracket. To select the proper part number for any
future cylinder applications. Accessories offered for the desired accessory refer to the charts below.
47
Cylinder
Series 2A
Accessories Heavy Duty Air Cylinders
➁ ➅ ➁ Female Rod Clevis
➇ CW CB CW
ER
+.004
➄ CD
+.002
CE
➧
A
KK THREAD
➂ ➃ Order to fit thread size.
Cylinder Accessories
Parker offers a complete range of cylinder accessories to assure you of
greatest versatility in present or future cylinder applications. ➂ Knuckle (Female Rod Eye)
Rod End Accessories
Accessories offered for the rod end of the cylinder include Rod Clevis, ER CD
+.004
Eye Bracket, Knuckle, Clevis Bracket and Pivot Pin. To select the proper +.002
A FULL
part number for any desired accessory, refer to Chart A below and look
opposite the thread size of the rod end as indicated in the first column.
The Pivot Pins, Eye Brackets and Clevis Brackets are listed opposite the
CD
CD
THREAD
➧
KK THREAD
thread size which their mating Knuckles or Clevises fit. CD CA CB
Chart A
Mating Parts Mating Parts
Thread Rod Eye Clevis Alignment Order to fit thread size.
Size Clevis Bracket Pin Knuckle Bracket Pin Coupler
5/16-24 51221 74077 — 74075 74076 74078 134757 0031 ➃ Clevis Bracket for Knuckle
7/16-20 50940 69195 68368 69089 69205 68368 134757 0044
1/2-20 50941 69195 68368 69090 69205 68368 134757 0050 CW CB CW
MR
3/4-16 50942 69196 68369 69091 69206† 68369 134757 0075 M 25˚
DD DIA
➧
CD + .004
3/4-16 133284 69196 68369 69091 69206 68369 134757 0075 LR
4 HOLES + .002
7/8-14 50943 *85361 68370 69092 69207 68370 134757 0088 FL
48
Series 2A Cylinder
Heavy Duty Air Cylinders Accessories
49
Series 2A
How to Order Heavy Duty Air Cylinders
How to Order Series “2A” Cylinders
When ordering Series 2A cylinders, please review the following:
Note: Duplicate cylinders can be ordered by giving the SERIAL Special Modifications: Additional information is required on orders
NUMBER from the nameplate of the original cylinder. Factory records for cylinders with special modifications. This is best handled with
supply a quick positive identification. descriptive notes. For further information, consult factory.
Piston Rods: Specify rod code number based on diameter. Give Fluid Medium: Series 2A hydraulic cylinders are equipped with seals
thread style number for a standard thread or specify dimensions. See for use with lubricated air.
“Style 3 Rod End” below.
Cushions: If cushions are required specify according to the model
number on the next page. If the cylinder is to have a double rod and
only one cushion is required, be sure to specify clearly which end of
the cylnder is to be cushioned.
Class 1 Seals
Class 1 seals are the seals provided as standard in a cylinder Piston Rod Wiper – Nitrile
assembly unless otherwise specified. For further information on fluid Piston Seals – Nitrile with polymyte back-up washers
compatibility or operating limitations of all components, see section C. O-Rings – Nitrile
For the 2A series cylinders the following make-up Class 1 Seals:
Primary Piston Rod Seal – Nitrile with PTFE back-up washers
Combination Mountings
Single Rod End The first mounting is the one called out on the head primary end at rod end #1. See Double Rod Models information page
end of the cylinder. The second or subsequent mountings are called in this section. For this option the piston rod number, piston rod end,
out as they appear in the assembly moving away from the rod end. and piston rod threads are to be specified for both ends. The simplest
Exception: When tie rod mountings are part of a combination, the are for symmetric cylinders such as: TD, C, E, F, G, and CB mounts.
model number should contain an “S” (Special) in the model code and All other mounting styless, the description of the first rod end will be at
a note in the body of the order clarifying the mounting arrangement. the mounting end. In the case of multiple mounts, the description of
The ”P” is used to define a thrust key and is not considered to be a the first rod end will be at the primary mounting end. For “DD”
mounting. However, it is located at the primary end. mounts, the description of the first rod end will be the same location
Example: 4.00 CCBB2ALTS14AC x 10.000 as the “XI” dimension.
Combination “C” mounting head only. “BB” mounting cap end Example: 4.00 KDD2ALT24A/18A x 10.000 XI=8
This cylinder is also cushioned at both ends. This is a center trunnion mounting cylinder with the XI dimension
Double Rod End In general, the model number is read left to right measured from the code 2 rod side of the cylinder which has the style
corresponding to the cylinder as viewed from left to right with the 4 thread. The opposite end code 1 rod with the style 8 thread.
50
Series 2A
Heavy Duty Air Cylinders Model Numbers
*Required for Basic Cylinder Model Number ‡Specify XI dimension Cylinder serial numbers are factory production record numbers and
Dark Arrows Indicate Basic Minimum Model Number are assigned to each cylinder, in addition to the model number.
††In case of Stop Tube, call out gross stroke length.
51