Beruflich Dokumente
Kultur Dokumente
Issue 4
Page 1 of 7
October 2014
Aerospace series
Rivet, blind 100, CSK
When this standard is applied, a careful check must be made as to whether any protective rights exist. This
standard issuer hereby disclaims any liability for infringement of patent or design rights resulting from the use of
this standard.
Copyright reserved
Ref. no. ABS0112
ABS0112
Issue 4
Page 2
Contents
Scope
Normative references
Requirements
Designation
Marking
Technical specification
ABS0112
Issue 4
Page 3
1 Scope
This standard specifies the dimensions, tolerances, required characteristics and the mass of a blind, 100 flush
shear head, self-locking rivet for nut plate installation or tacking purposes in aerospace applications..
2 Normative references
This Airbus Standard incorporates by dated or undated reference provisions from other publications. All normative
references cited at the appropriate places in the text are listed hereafter. For dated references, subsequent
amendments to or revisions of any these publications apply to this Airbus Standard only when incorporated in it by
amendment of revision. For undated references, the latest issue of the publication referred to shall be applied.
ASTM A493
Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold
1
Forging
AMS-QQ-P-416
AMS2700
AMS5731
Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 15Cr
25.5Ni 1.2Mo 2.1Ti 0.006B 0.30V, Consumable Electrode Melted, 1800F (982C)
2
Solution Heat Treated
MIL-PRF-46010
Lubricant, solid film, heat cured, corrosion inhibiting NATO code -S-1738
MIL-STD-129
NASM25027
SAE AS5272
2
2
Published by: American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 194282959, USA
2
Published by: Society of Automotive Engineers (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA
3
Published by: Department of Defense (DoD), the Pentagon, Washington, D.C., 20307, USA
4
Published by: Aerospace Industries Association of America, Inc. (AIA), 1250 Eye Street, N.W., Washington, D.C. 20005-3924,
USA
ABS0112
Issue 4
Page 4
3 Requirements
3.1
The configuration, dimensions, tolerances and mass shall be in accordance with figure 1, table 1 and table 2..
not to exceed
D
A1
stem
100
1
Head marking
NOTE:
When installing,
stem pulls completely
through and leaves
hollow rivet.
B
grip
sleeve
Figure 1 Configuration
Diameter
code
-24
-32
Nominal
Diameter
A
theoretical
Min
Max
4,45
4,65
A1
Min
3,84
Ref
0,91
2,40
Min
2,34
Max
2,46
(.094)
3,20
(.092)
3,12
(.097)
3,25
(.175)
5,62
(.183)
5,82
(.151)
5,00
(.036)
1,07
(.126)
(.123)
(.128)
(.221)
(.229)
(.197)
(.042)
Max
Min
2,34
Max
2,46
0,05
0,25
(.002)
(.010)
(.092)
3,12
(.097)
3,25
(.123)
(.128)
ABS0112
Issue 4
Page 5
Length
code
Diameter code
Grip range
02
03
04
05
06
-24
F
Min
Max
Max
Max
1,60
3,20
5,16
7,14
(.063)
3,20
(.126)
4,78
(.203)
6,73
(.281)
8,71
(.126)
4,78
(.188)
6,38
(.265)
8,33
(.343)
10,29
(.188)
6,38
(.251)
7,95
(.328)
9,91
(.405)
11,89
(.251)
7,95
(.313)
9,55
(.390)
11,51
(.468)
13,46
(.376)
11,10
(.453)
13,08
(.530)
15,06
07
(.313)
9,55
08
(.376)
11,10
(.437)
12,70
(.515)
14,68
(.592)
16,66
09
(.437)
12,70
(.500)
14,30
(.578)
16,26
(.655)
18,24
10
(.500)
14,30
(.563)
15,90
(.640)
17,86
(.718)
19,84
11
(.563)
15,90
(.626)
17,42
(.703)
19,43
(.780)
21,41
12
(.626)
17,42
(.686)
19,05
(.765)
21,03
(.843)
22,99
(.686)
(.750)
(.828)
(.905)
Mass
(kg / 1000
pieces)
0,100
0,131
0,163
0,195
0,227
0,258
0,290
0,322
0,354
0,385
0,417
5,89
8,53
(.232)
7,49
(.318)
10,14
(.295)
9,07
(.381)
11,71
(.357)
10,67
(.443)
13,31
(.420)
12,24
(.506)
14,88
(.482)
13,84
(.568)
16,49
(.544)
15,42
(.630)
18,06
(.607)
17,02
(.693)
19,66
(.670)
18,59
(.755)
21,23
(.732)
20,19
(.818)
22,84
(.795)
22,23
(.899)
24,41
(.857)
(.961)
0,133
0,174
0,217
0,250
0,302
0,344
0,387
0,429
0,472
0,513
0,556
a These lengths are only available on special order. Consult standards group prior to call up
3.2
The material and surface treatment shall be in accordance with table 3. These blind rivets will be supplied in
lubricated condition and must not be degreased prior to installation.
Table 3: Material and surface treatment
Material
code
None
T
P
Material
Sleeve
Finish
Stem
Sleeve
Stem
ABS0112
Issue 4
Page 6
4 Designation
This type of standard shall be designated according to the philosophy of the following example:
Description block
Rivet, blind, 100 CSK
Identity block
ABS0112
5 Marking
MIL-STD-129.
6 Technical specification
Torque- and push-out strength to meet or exceed the requirements of NASM25027.
-24
-02
ABS0112
Issue 4
Page 7
RECORD OF REVISIONS
Issue
Clause
modified
Description of modification
All
New standard.
3.1
Figure 1 modified.
Table 1 updated, rounding errors corrected, dimensions A1 and C added. Hole
diameters from former separate table added. Dimensions F and L updated.
Table 2 updated, rounding errors corrected.
3.2
10/14