Beruflich Dokumente
Kultur Dokumente
constructive solutions
Properties
Advantages
Test method
Compressive
strength
(BS 6319, Part 2):
Flexural strength
(BS 6319 Part 3):
Tensile strength
(BS 6319, Part 7):
Compressive
modulus
(ASTM C-469:65);
Pot life: 20oC
35oC
Initial hardness:
o
20 C
35oC
Full cure:
o
20 C
35oC
Fresh wet density:
Chemical resistance:
Technical support
Fosroc offers a comprehensive range of high
performance, high quality concrete repair and construction
products. In addition, Fosroc offers a technical support
package to specifiers, end-users and contractors, as well
as on-site technical assistance in locations all over the
world.
Chemical Agent
Citric acid
Tartaric acid
Hydrochloric acid
Sodium hydroxide
Diesel fuel/petrol
Sulphuric acid
Sugar solutions
Lactic acid
Hydrocarbons
Phosphoric acid
Nitric acid
Acetic acid
Design criteria
Nitomortar HB can be applied in sections up to 50 mm
thickness in vertical and overhead locations in a single
application and without the use of formwork. Thicker
sections up to 75 mm are possible in smaller locations,
Page 1
Typical result
40 N/mm2 at 28 days
15 N/mm2 at 28 days
7 N/mm2 at 28 days
2
4.5 kN/mm at 28 days
45 minutes
20 minutes
24 hours
16 hours
7 days
4 days
3
Approximately 1160 kg/m (fully
compacted)
The
low
permeability
of
Nitomortar HB retards chemical
attack
in
aggressive
environments. Performance of
Nitomortar
HB
blocks
o
continually immersed at 20 C.
Concentration
Resistance
10%
Excellent
10%
Excellent
25%
50%
100%
10%
Saturated
10%
100%
10%
10%
5%
Excellent
Excellent
Excellent
Very good
Very good
Very good
Very good
Very good
Good
Limited
Nitomortar HB
Specification clauses
Mixing
Care should be taken to ensure that Nitomortar HB is
thoroughly mixed to produce a fully homogeneous,
trowellable mortar.
Application instructions
Preparation
Clean the surface and remove any dust, unsound
material, plaster, oil, paint, grease, corrosion deposits or
algae. Roughen the surface and remove any laitance by
light scabbling or grit-blasting. Saw cut or cutback the
extremities of the repair locations to a depth of at least 10
mm to avoid feather edging and to provide a square edge.
Break out the complete repair area to a minimum depth of
10 mm up to the sawn edge.
Application
Substrate priming
The substrate should be primed using Nitoprime 28. The
primer should be mixed in the proportions supplied,
adding the entire contents of the hardener tin to the
base tin. The two components should be thoroughly
mixed together for 3 minutes.
The mixed primer should be scrubbed well into the
prepared substrate, taking care that all imperfections in
the surface are properly coated and avoiding pudding in
depressions.
constructive solutions
Page 2
Nitomortar HB
Build-up
Cleaning
Nitoprime Zincrich, Nitoprime 28 and Nitomortar HB
should be removed from tools, equipment and mixers with
Fosroc Solvent 102 immediately after use.
Limitations
Finishing
Nitomortar HB is finished by the use of a wood float and
closed with a steel trowel wiped with a cloth dampened
with Fosroc Solvent 102. The completed surface should
not be overworked.
Low temperature working
Estimating
Supply
Nitomortar HB:
Nitoprime Zincrich:
Nitoprime 28:
Fosroc Solvent 102:
Curing
UN packaging regulations
To comply with current regulations, all product of a
hazardous nature that are involved in a sea crossing as
part of the delivery requirements must be packed in United
Nations Approved receptacles.
When a known sea crossing is involved, whether local to
the Saudi Arabia or for export worldwide, Fosroc will
supply in the correct UN packaging. Where Fosroc are
only requested to deliver within the Saudi Arabia
constructive solutions
Page 3
Nitomortar HB
Fire
Nitomortar HB is non-flammable.
Nitoprime Zincrich,
Nitoprime 28 and Fosroc Solvent 102 are flammable. Keep
away from sources of ignition. No smoking. In the event of
fire, extinguish with CO2 or foam. Do not use a water jet.
Flash point
Storage
Nitoprime Zincrich:
Nitoprime 28:
Fosroc Solvent 102:
Shelf life
o
All products have a shelf life of 12 months at 20 C if kept in
a dry store in the original, unopened bags or packs.
o
16 C
o
27 C
o
33 C
Additional information
Storage conditions
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
www.fosroc.com
email: fosam@fosroc.com
Regional Offices
Jeddah Sales Office
Jeddah Showroom
Riyadh
Dammam
Khamis Mushayt
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 4
FO SA/NITOMORTAR HB/05/A