Beruflich Dokumente
Kultur Dokumente
MODEL
P/N:
41135C
40083A
TRAV SEQ.
BATTERY VOLTAGE
(B+) and (B-)
Non Switched
36.0Vdc
PIN 1
5K Pot. Low
( 0Vdc )
(Output)
PIN 2
5K Pot. Wiper.
Not Used
PIN 3
( B- ) ( Input )
( 0-5Vdc )
( Input )
PIN 4
PIN 5
PIN 6
PIN 7
PIN 8
PIN 9
Not Used
Not Used
OUTPUT (M2)
0Vdc in forward traverse.
0Vdc to 24Vdc in reverse
traverse.
36.0Vdc / 45Amps
Cont.
Not Used
Not Used
Open Collector closed when in traverse, forward or Open Collector closed to turn on
reverse, with a 2.0 sec. delay off when going to
the (Main) solenoid. 36.0Vdc /
neutral. 36.0Vdc / 1.0Amp Cont. ( Output )
1.0Amp Cont. (Output)
Not Used
Not Used
Not Used
Not Used
Not Used
Open Collector closed when in traverse, forward or Open Collector closed to turn on
reverse, with a 2.0 sec. delay off when going to
the (Main) solenoid. 24.0Vdc /
neutral. 24.0Vdc / 1.0Amp Cont. ( Output )
1.0Amp Cont. (Output)
PIN 10
OUTPUT (M1)
Not Used
(Output)
40089A
Switched 36.0Vdc
5K Pot. Low
( 5Vdc )
(Output)
5K Pot. Wiper
( 5-10Vdc )
(Output)
Not Used
Not Used
41160A
Note 2:
41144D
Control Only.
Battery
41150A
connected,
the key
switch ON,
the machine
will40132A
freely roll
backwards,
the controller
is in
electrical
Neutral.
Battery
connected,
the key
41153A
switch OFF
PLUG (#1)
the controller
DAC
is in the
braking
mode,
41153A
the
traverse
PLUG (#2)
motor
DAC
shorted.
Battery
Note 1:
disconnecte
41154A must
41154A
d,
key
bethe
designed
ACT CONT
switch
to be ON or
See
Note
OFF
the 1
completely
traverse
compatible
motor
is in
with the
the
braking
41153A
DAC
mode,
(Digitalthe
to
traverse
Analog
41144D
motor
Conveter)
See Note 2
shorted.
module.
The
See braking
41153A
mode
must
Electrical
prevent
the
Specification
controller
sheet.
from being
destroyed
during
pushing or
pulling or
coasting of
the machine.
Switched 36.0Vdc
Not Used
Not Used
Not Used
Switched 24.0Vdc
5K Pot. Low
( 5Vdc )
(Output)
5K Pot. Wiper
( 5-10Vdc )
Switched 24.0Vdc
5K Pot. Low
( 5Vdc )
(Output)
5K Pot. Wiper
( 5-10Vdc )
(Output)
(Output)
Not Used
Not Used
Not Used
( B- ) ( Input )
Not Used
( B- ) ( Output )
Not Used
(2.0-9.0Vdc) Wiper
voltage from the Brush
Pressure Module
(50170A) ( Input )
(36.0Vdc) when the brush head is lowered to the floor to Millivolt voltage drop, 0.03Vdc maximum, across
provide (B+) to the brush solenoid for turn on when the the (M1) and (M2) terminals during the on-state
traverse is selected. ( Output )
and 36Vdc during the off-state. ( Output )
Not Used
( B- )
( Input )
Not Used
Not Used
( B- )
( Input )
Not Used
Not Used
Not Used
Switched 36.0Vdc
Not Used
Not Used
Not Used
Not Used
Not Used
Connect P9 to P4.
Not Used
24.0Vdc
5K Pot. Low
( 5Vdc )
(Output)
Connect P4 to P9.
Not Used
Note 3: For all above controls, except 41144D. With the batteries connected or disconnected and with the key switch ON or OFF and the controller in Neutral traverse, the machine
must be in the braking mode. The braking mode must prevent the controller from being destroyed during pushing or pulling or coasting of the machine.
Note 4: For all above controls. Input Connector = 10 Pin Molex or equiv. (0.05" Sq. Pin with 0.156" Center Spacing). All other connectors are (0.25" X 0.03" Male Tabs).
Not Used
Not Used