Sie sind auf Seite 1von 2

Product Data

1/2

HEMPELS EPOXY FILLER 35230


BASE 35239 with CURING AGENT 95130

Description:

HEMPELS EPOXY FILLER 35230 is a two-component, high solid, epoxy filler, which when fully cured - is resistant to water, aliphatic hydrocarbons, and related products.
The products is easy to work with, has excellent filling properties and can be recoated
with epoxy and polyurethane coating systems.

Recommended use:

As a repair filler or levelling compound for interior steel, concrete, hardwood and other
rigid materials.

Availability:

Not included in Group Assortment. Local availability subject to confirmation.

PHYSICAL CONSTANTS:
Colours/Shade nos:
Finish:
Volume solids, %:
Flash point:
Specific gravity:
Dry to touch:
Ready to sand:

Off-white/11630 - Pastel blue/3010S


Flat
98 1
25C/77F
2.0 kg/litre - 16.7 lbs/US gallon
3 (approx.) hours at 20C/68F
16 (approx.) hours at 20C/68F
The physical constants stated are nominal data according to the HEMPEL Group's approved formulas. They are
subject to normal manufacturing tolerances and where stated, being standard deviation according to ISO 3534-1.

APPLICATION DETAILS:
Mixing ratio for 35230:
Application method:
Thinner (max.vol.):
Pot life:
Cleaning of tools:
Recoat interval, min:
Recoat interval, max:

Base 35239 : Curing agent 95130


3 : 1 by volume
Spatula, putty knife or similar
Do not dilute (See REMARKS overleaf)
2 hours (20C/68F)
HEMPELS TOOL CLEANER 99610 or THINNER 08450
24 hours (20C/68F)
30 days (20C/68F)

Safety:

Handle with care. Before and during use, observe all safety labels on packaging and
paint containers, consult HEMPEL Material Safety Data Sheets and follow all local or
national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do
not swallow. Take precautions against possible risks of fire or explosions as well as
protection of the environment. Apply only in well ventilated areas.

Issued: January 2005

Page 1 of 2

HEMPEL
Product Data Sheet

2/2

HEMPEL'S EPOXY FILLER 35230


SURFACE
PREPARATION:

The surface must be sound and free from dust, loose paint, oil/grease and other contaminants.
Metal: Remove oil and grease, etc. with suitable detergent. Remove salt and other contaminants
by (high pressure) fresh water cleaning. Abrasive blasting, power tool cleaning or sanding,
depending on material and condition of the surface. Finally clean the area with HEMPELS THINNER
08450. Priming after abrasive blast cleaning, but prior to filling, can be done with a thin layer of
e.g. HEMPADUR 15590.
Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by
high pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and
uniform surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid
etching. Seal surface with suitable sealer, e.g. HEMPADUR SEALER 05990, prior to filling.

APPLICATION
CONDITIONS:

Use only where application and curing can proceed at temperatures above 5C/41F.
The temperature of the substrate should also be above this limit.
Apply only on a dry and clean surface with a temperature above the dew point to avoid
condensation.

SUBSEQUENT
COAT:

Can be recoated with HEMPALIN, HEMPATEX or HEMPADUR qualities according to specification.


High-gloss finishes such as HEMPATHANE TOPCOAT, should not be applied directly on top of
HEMPADUR FILLER 35250. An intermediate coat e.g. of a suitable HEMPADUR coating is
recommended.

REMARKS:

Note:

Mix and stir the two components thoroughly until an even colour is achieved, whereafter the filler is
ready for use. Do not mix more than is necessary for use within the pot life.
If the maximum recoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion.
May be sanded after 16 hours (20C/68F).
Normally, the product is not diluted before application, but when used as skim coat, 5% THINNER
08450 may be added.
HEMPELS EPOXY FILLER 35230 is for professional use only.

ISSUED BY:

HEMPEL PAINTS (SAUDI ARABIA) W.L.L. - 3523011630CS002

This Product Data Sheet supersedes those previously issued.


For explanations, definitions and scope, see Explanatory Notes in the HEMPEL Book.
Data, specifications, directions and recommendations given in this data sheet represent only test results or
experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF
SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Seller
disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence,
except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or
damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.
Issued: January 2005

Page 2 of 2

Product Data Sheet

Das könnte Ihnen auch gefallen