Beruflich Dokumente
Kultur Dokumente
- One USB memory device of over 512MB capacity formatted on the MOTIF XS
1. After downloading, copy the uncompressed [8E54OS_.PGM] file to a USB memory d
evice that has been formatted on the MOTIF XS. No other files should be present
on the USB memory device.
2. Power off the MOTIF XS.
3. Connect the USB memory device copied in step 1 into the MOTIF XS. Power on th
e MOTIF XS while holding down the cursor [UP] button and [UTILITY] buttons until
the "MOTIF XS" logo appears on screen.
4. The MOTIF XS OS updater will begin with the message "Searching for the firmwa
re updater," indicating "......%".
When the message "Finish. Please turn off " appears, turn off the MOTIF XS and r
emove the USB memory device.
NOTE:
The update process takes from several to fifteen minutes (It may change with con
ditions.). DO NOT power off or remove the USB device from the MOTIF XS during th
is time. If the electrical supply is accidently interrupted while running the up
dater (by pulling out the AC cord, etc.), the unit may become inoperable. If thi
s happens, run the updater again. If the unit does not function after doing this
, please contact your nearest Yamaha service center.
5. If you are updating from V1.50 or an earlier version, make sure to execute th
e Initial Factory Setting by pressing [UTILITY] -> [JOB] -> [ENTER].
After the Initial Factory Setting is completed, load the data you backed up befo
re this procedure to the MOTIF XS, if necessary.
6. Press the [UTILITY], [Cursor Up] and [F1] buttons simultaneously to check the
firmware version to confirm that the unit has been successfully updated.
This concludes the update process.
Main Fixes and Enhancements
<V1.56 to V1.60>
New features;
-Normalize, Slice, and Remix have been added to the Sampling Edit display and Sa
mpling Main display respectively, allowing you to more easily call up these disp
lays.
-You can now increase the available memory of the DIMM by using the newly added
Sampling Job.
-You can now convert a Sample Voice to a Mixing Voice.
-You can now edit a Drum Voice in the Mixing mode.
-TAP is now available in the Voice/Performance/Song/Pattern mode.
-Network function now supports Windows 7 and Mac OS X 10.6 .
- From this new version, "meas" cannot be selected on the SAMPLE Record display
in the Song or Pattern mode when the MIDI Sync is set to "MTC."
Solved problems;
- Fixed a problem in which "Int Switch" and "Ext Switch" would not work properly
in the Song mode and the Pattern mode when the "TxCh" value was different from
<V1.51 to V1.55>
Solved problems;
-Fixed a problem in which the process speed of the MOTIF XS becomes slow when se
lecting the MOTIF XS Voice from the Media Bay of Cubase for Mac OS X, causing an
unnecessary repetition of transmission of a certain message between the MOTIF X
S and computer.
-Fixed a problem in which the value of the High Threshold parameter of the Effec
t Type "Multi Band Comp" would not be set properly even if you change the Voice,
Performance, Effect Type or Effect Preset.
-Fixed a problem in which the fade-in and fade-out of the Common LFO might not w
ork correctly when either of the "InsA1"-"insA16" or "InsB1"-"insB16" is assigne
d to Dest of the Common LFO in the Voice Edit mode.
-The value of the Rotor/Horn Balance parameter belonging to the Effect Type "Rot
ary Speaker" has been corrected from "L63>H"-"L=H"-"L<H63" to "R63>H"-"R=H"-"R<H
63."
<V1.50 to V1.51>
Solved problems;
-Fixed a problem in which the output levels for the mLAN IN Main Out Monitor L/R
and mLAN IN Assignable Out Monitor L/R of the IEEE1394 audio input channels exc
eeded the values you specified by 12dB.
<V1.12 to V1.50>
New features;
- With the newly added Audio Record / Play function, you can now record your per
formances on the MOTIF XS as WAV-format audio files (44.1-kHz, 16-bit, stereo) o
n a USB storage device or a computer connected via a network.
- Whenever using the [F1] File display of the File mode to transfer files to or
from a USB storage device or a networked computer, the new Audition function mak
es it easy to preview WAV or AIFF files before importing them into the MOTIF XS.
-The Cursor up/down buttons can now move the cursor in the Directory list, Shari
ng Point list and Device list of the File mode. Also, the Cursor left/right butt
ons can move the cursor from or to the list box in the display of the File mode.
Pressing the Cursor left button moves the cursor up, and pressing the Cursor ri
ght button moves the cursor down.
-The Sampling Main display now contains a list of the Key Banks that make up the
selected Waveform. In this display, the Cursor [<]/[>] buttons can now move the
cursor up/down.
-You can now edit the following parameters of the [F2] Parameter display in the
[F1] Trim display from Sampling Edit.
Level, Pan, Coarse Tune, Fine Tune, Play Mode, Key Range, Velocity Range
-The initial settings of the "Play Mode" have been changed from "one shot" to "l
oop" in the [F1] Trim display of the Sampling Edit mode.
-When you press the [SF4] Apply button from the Sampling mode to temporarily mod
ify data, it will be replaced with a Cancel button.
-Sequence data bars on the Song Play Track View display now indicate the relativ
e pitches of note events with higher-pitched notes being displayed at a higher p
osition.
-You can now customize MOTIF XS displays using file sharing functionality via a
network.
-A message "Press [ENTER] to set." now apper in the Input Character window.
Solved problems;
-Fixed a problem in which the release time might become longer than the AEG sett
ing if you play the keyboard while using the optional foot controller with the h
alf-damper feature (FC3, etc.) when "Half Damper Switch" is set to "on" via [F4]
Amplitude -> [SF2] AEG in the Voice Element Edit mode.
-Fixed a problem in which the LFO speed is not synchronized to the tempo of the
Arpeggio or sequencer when the load on the MOTIF XS becomes too large, even if "
Tempo Sync" is set to "on" called up via [F5] Com LFO -> [SF1] Wave in the Voice
Common Edit mode.
-Fixed a problem in which the [ASSIGNABLE FUNCTION] button would not work even i
f the current part is the part corresponding to the MIDI channel set in "Transmi
t Channel" when the settings below have been made in the Master Edit mode.
[COMMON EDIT]
[COMMON EDIT]
Number button
her than "1"
Number button
Number button
1,2" = "on"
To change the current part when setting "Mode" to "Song"/"Pattern" in the Mas
ter mode, press the [SELECTED PART CONTROL] button to call up the Control Funct
ion window and then press Number button [1] - [16].
Known Issues;
-File sharing for accessing the computer of the systems below from the MOTIF XS*
will not function correctly. The functionality for accessing the MOTIF XS from
a computer will function correctly.
- Windows Vista
- Mac OS X 10.4.11 or later, and 10.5.4 or later
@*This issue is targetd at all firmware versions of MOTIF XS.
<V1.10 to V1.12>
Solved problems;
- Fixed a problem in which the user Waveforms assigned to the Mixing Voices cann
ot be loaded to the MOTIF XS if you saved the Mixing Voices in the Song mode/Pat
tern mode as a file type other than "all."
- Fixed a problem in which the ASSIGN1/2 knob operations in the Song data affect
the current Part as well as the Parts specified as the channels for control by
MIDI Control Change messages when the Song plays back.
- Fixed a problem in which the wrong Insertion Effect might be selected unexpect
edly and could not be corrected by changing the program number of the Performanc
e/Song/Pattern/Master or by changing the mode, depending on both the parameter s
ettings before and those after changing.
<V1.07 to V1.10>
New features;
- Supports USB-ASCII keyboard, allowing you to use conventional computer keyboar
ds to edit parameters (by connecting it to the USB TO DEVICE terminal).
- Added the new parameter "IEEE1394Driver" called up via [UTILITY]->[F1] "Genera
l" -> [SF4] "AutoLoad".
- All the notes you are holding will be maintained even when the current track o
r part is changed in the Song mode or Pattern mode.
- The values of the Location 1 and 2 can be copied to the Punch In and Punch Out
respectively when the Record Type is set to "punch" on the Record Setup display
in the Song mode.
- The default value of the MIDI Sync parameter of the Setup Number 3 (Recording
on computer) on the [SEQ SETUP] -> [F3]"Quick" window is now set to "Auto" (inst
ead of "Internal" in the previous version).
- The Program can be changed even when the wrong or insufficient MIDI messages c
ome from the external MIDI device. Even when the order of the Bank Select MSB an
d LSB is wrong or the Bank Select messages are missing, the program can be chang
ed.
- The user name to log into the network computer can be stored on the MOTIF XS a
s a parameter.
- The parameter name of "Stereo/Mono" in the Sample Record display has been chan
ged to "Mono/Stereo". The settings of this parameter are changed from "mono L",
"mono R" and "mono L+R" to "L mono", "R mono" and "L+R mono".
Solved problems;
- Fixed a problem in which the MOTIF XS would freeze when the Mode was changed w
hile receiving the MIDI messages output from the MOTIF XS itself via USB Port 4
to the computer then transmitted from the DAW back to the MOTIF XS itself via US
B Port 1.
- Fixed a problem in which more than 256 Mixing Voices could be stored by using
the MOTIF XS Editor.
- Fixed a problem in which editing the Note Shift parameter called up via [UTILI
TY] -> [F1] "General" -> [SF1] "Play " would change the Drum Key (drum instrumen
t) instead of pitch.
- Fixed a problem in which the MOTIF XS might freeze when the MIDI buffer become
s full.
- Fixed a problem in which the Firmware Upgrade mode would not be called up when
the Control Slider was set to a certain location even when turning the power on
while holding the Cursor Up button and [UTILITY] button.
- Fixed a problem in which the sound changes by the Filter Cutoff might be delay
ed when the Filter Cutoff
and Resonance parameter are controlled simultaneously via the Common LFO setting
s ([VOICE] -> [EDIT] ->
[COMMON] -> [F5] "Com LFO" -> [SF2] "Set"), Controller Set settings ([VOICE] ->
[EDIT] -> [COMMON] -> [F4] "Ctrl Set"),
- Fixed a problem in which the MOTIF XS responded to the MIDI messages "FA" (Sta
rt) and "FB" (Continue) when you call up the Sampling Edit window in the Song mo
de or the Pattern mode.
- Fixed a problem in which the "Next" indication would not appear even when you
change the Arpeggio Type was changed by pressing any of the [SF1] ARP1 - [SF5]
ARP5 buttons at the middle of a measure on the [F2] "Arpeggio" display in the S
ong Record mode or Pattern Record mode.
- Fixed a problem in which receiving an FC (stop) message could not stop the Sam
pling operation performed after the Recording Type was set to "sample + note" in
the Song mode or Pattern mode.
- Fixed a problem in which the Edit indicator would disappear in the Song mode o
r Pattern mode when you go to the Sampling display was returned to from the Mixi
ng display with the Edit indicator shown, and then return back to the Mixing dis
play.
- Fixed a problem in which pressing the Footswitch during playback/recording/sam
pling would change the Song number or Pattern number unexpectedly when #98 (Inc)
or #99 (Dec) was assigned to the Foot Switch Control No. in the window called u
p via [MIXING] -> [EDIT] -> [COMMON] -> [F3] "Ctrl Assign".
- Fixed a problem in which all the Effect Switches of Parts 1 - 8 would be turne
d off regardless of the checkmark setting of the Parts if the Job was executed a
fter removing the checkmark of All Parameters on the [MIXING] -> [JOB] -> [F1] "
Init" in the Song mode or Pattern mode.
- Fixed a problem in which the currently-sounding notes might be stuck when the
MOTIF XS would receive the F2 (Song Position) message from the external MIDI dev
ice in the Pattern Chain mode.
- Fixed a problem in which the Sample Voice producing no sound would be maintain
ed although the Wavform would be deleted when executing but failing the Copy Job
called up via [JOB] -> [F2] "Waveform" -> "01:Copy" ( "Sample memory full" appe
ared).
- Fixed a problem in which the message gIllegal sample data. h would appear and you
cannot call up the Rec Standby display could not called up after executing the
Delete Job ([INTEGRATED SAMPLING] -> [JOB] -> [F2] "Waveform" -> "02: Delete") w
ith 1024 User Waveforms being stored to user memory.
- Fixed a problem in which a Time Out Error would occur when the [REMOTE ON/OFF]
button would be turned on in a mode other than Song and perform the Auto Sync w
ould be executed from the MOTIF XS Editor on the computer.
- Fixed a problem in which a data handling error would occur if you set the ARP
Assign Velocity Rate Offset parameter or ARP Assign Gate Time Offset parameter w
as set to a value more than the upper limit via the MIDI Parameter Change or MID
I Bulk message.
- Fixed a problem in which the MIDI Checksum Error would appear when the MOTIF X
S would receive a MIDI Parameter Change or bulk message including the data of wh
ich the value was over the specified range.
- Fixed a problem in which the name of the Voice, Performance, Song, Pattern, an
d Master could be changed via MIDI Parameter Change or Bulk message including th
e prohibited colon (:) character.
<V1.06 to V1.07>
New features;
- In this new version, the new data loaded to the current Song/Pattern can be pl
ayed back or edited immediately after the Load operation is completed. (This was
impossible in the previous version.) In the previous version, the new data load
ed to the current Song/Pattern could be played back only after selecting a diffe
rent Song/Pattern then the selecting the original Song/Pattern again.
Solved problems;
- Fixed a problem in which selecting a Voice via the Category Search function wo
uld transmit the Bank Select MSB/LSB and Program Change via MIDI although the Ba
nk Select and Program Change parameters were properly set to off in the [F5] "Co
ntrol" display of the Utility mode.
- Fixed a problem in which changing the Reverb/Chorus/Insertion parameters (via
both panel operation and incoming MIDI messages) would produce no effect after t
<V1.05 to V1.06>
New features;
- While samples already recorded are being played back, a new sample can be reco
rded to a different Key Bank in the same waveform in the Sampling Record mode fo
r the Song/Pattern mode by setting the Recording Type to gsample+note. h
- The destination key for Key Bank can now be specified for the Sampling mode Ke
ybank Job g01:Copy. h
- When using Copy Performance in the Mixing Job mode, the receive channels for t
he destination part (Current Mix Part) are set as below.
Current Mix Parts 1 `4 : Receive Channel 1
Current Mix Parts 5 `8 : Receive Channel 5
Current Mix Parts 9 `12 : Receive Channel 9
Current Mix Parts13 `16 : Receive Channel 13
- When using Template Performance in the Mixing Job mode, the receive channels f
or the destination part (Current Mix Part) are set as below.
Current
Current
Current
Current
Mix
Mix
Mix
Mix
Parts 1
Parts 5
Parts 9
Parts13
`4 : Receive Channels 1 `4
`8 : Receive Channels 5 `8
`12 : Receive Channels 9 `12
`16 : Receive Channels 13 `16
[NOTE]
The receive channels for the destination Song/Pattern are turned off for Parts f
or which Part Switch is off in the original performance.
- The settings other than those for the receive channels of a target track can n
ow be copied to tracks 1 to 8 by executing the Track Job g06:Divide Drum Track h in
the Song/Pattern mode.
Solved problems;
- Fixed a problem in which Elements 5 to 8 for the Voice data loaded from the MO
TIF ES would not sound on the MOTIF XS, even if those Elements were properly set
on the MOTIF XS.
- Fixed a problem in which the lamp for the [ASSIGNABLE FUNCTION] button did not
work properly when turning the [ASSIGNABLE FUNCTION] button on and entering the
Compare mode.
- Fixed a problem in which the Source set to gModWheel (Modulation Wheel) h or gFoot
Ctrl1/2 (Foot Controller 1/2) h on the Controller Set display of the Voice Common
Edit mode was not available when gFoot controller 1/2 Control No. h was set to g01 (
Modulation Wheel) h on the Controller Assign display in the Performance/Mixing mod
e or the Control display in the Utility mode.
- Fixed a problem in which the Performance name would not change when the parame
ter change for the Performance name was received from external equipment in the
Performance mode.
- Fixed a problem in which the lamp for the [ASSIGNABLE FUNCTION] button did not
work properly when storing a performance or when selecting another performance
by turning the [ASSIGNABLE FUNCTION] button on while gController Reset h was set to
ghold h in the Performance mode.
- Fixed a problem in which the initial note would sometimes not be recorded when
turning the Key On Start Switch on in the Performance/Pattern Record mode.
- Fixed a problem in which the data converted by the Track Job g07: Put Track to
Arpeggio h in the Song/Pattern mode could not be stored to Arpeggio number 129 of
the User Arpeggios.
- Fixed a problem in which the Voice data transmitted as bulk data from MOTIF XS
Editor could not be received when the default Mixing Voice was selected in the
Song/Pattern mode.
- Fixed a problem in which the phrase length became longer than the actual setti
ng when phrase recording was stopped while the sustain pedal was on in the Patte
rn mode.
- Fixed a problem in which the range to be applied (Measure/Beat/Clock) was not
available for the Event Jobs g01: Shift Clock h and g08: Beat Stretch h in the Pattern
mode.
- Fixed a problem in which the Pattern Chain was not played back from the measur
e set by gMeasure. h
- Fixed a problem in which the note events for the last section of the Pattern C
hain were occasionally not played back according to the gate time setting.
- Fixed a problem that when a phrase longer than a section was assigned to the s
ection and some of the subsequent sections were set to a different time signatur
e, phrases for the subsequent sections were sometimes deleted.
For example:
If section A's length was 4 and the time signature was 4/4, and section B's leng
th was 4 and the time signature was 1/4, phrases for section B and the subsequen
t sections disappeared when assigning a phrase longer than a length of 4 to sect
ion A,.
- The default setting for the ARP1 (Arpeggio 1) Type in the Mixing Part Edit mod
e has been changed to the Arpeggio type gMA_Pf Arpl, h which is suitable for the Vo
ice g001 Full Concert Grand h which is assigned to each part.
- Fixed a problem in which the Insertion Effect switches for some Parts (Parts 1
to 8) were sometimes turned off when executing the initialization with gAll Para
meters h set to off on the Initialize display in the Mixing Job mode.
- Fixed a problem in which the Mixing Template setting recalled with the [SF4] G
et button on the MOTIF XS Template Mixing display in the Mixing Job mode did not
correspond with MOTIF XS Editor when the device and the editor were connected o
nline.
- The MOTIF XS now stops communication with MOTIF XS Editor temporally and the e
ditor now shows a message when entering the Sampling mode from the MOTIF XS whil
e the device and the editor are connected online.
- Fixed a problem in which noise was produced when a fade-out was started using
the Keybank Job g07: Fade In/Out h in the Sampling mode.
- Fixed a problem in which notes were sometimes inserted to the first measure ev
en if the starting point was set to a value other than 1 when recording by setti
ng the Recording Type to gsample+note h in the Sampling Record mode of the Song/Pat
tern mode.
- Fixed a problem in which unexpected noise such as a metallic sound was sometim
es produced when playing a waveform from DIMM memory (?) and the preset Voice si
multaneously and the number of notes being played was increased.
<V1.04 to V1.05>
New features;
In the Voice Edit mode, the methods for switching an Element on/off (Owner's Man
ual page. 97) and for switching on only the Element to be edited (Owner's Manual
page. 97) have changed.
- The method of selecting an Element to edit in the Voice Edit mode has not chan
ged from the previous version. However in V1.05, you can always use the number b
uttons [1]-[8] to select an Element, regardless of the state of the [MUTE] butto
n and [SOLO] button indicators. In V1.05, the [1]-[8] buttons indicate the Eleme
nt being edited, and the [9] to [16] buttons indicate the on/off status of Eleme
nts 1-8.
-To switch each Element on/off, turn the [MUTE] button on, and then use number b
uttons [9]-[16].
Use number buttons [1]-[8] to select the Element you want to edit
Use number buttons [9]-[16] to turn each Element on/off
- If you want to turn on only the Element you're editing, press the [SOLO] butto
n to turn it on, and then press a number button [1]-[8] or [9]-[16]. For example
if you want to turn on only Element 1 and edit it, press the [1] or [9] button
to make the [1] indicator light and the [9] indicator flash.
Use number buttons [1]-[8] / [9]-[16] to turn on only the Element you wa
nt to edit
In the Song mode Track View screen (p.181) and in the Pattern mode Play screen (
p.208), you can now use the Category Search function to select a Voice.
- In the Song mode Track View screen (p.181) or the Pattern mode Play screen (p.
208), press the [CATEGORY SEARCH] button; the indicator will light, and the Cate
gory Search screen will appear. This means that you can use the same method as e
xplained in "Using Category Search" (Owner's Manual page.24) to select a Voice f
or the mixing part that corresponds to the currently selected track. When you pr
ess the [CATEGORY SEARCH] button once again, the indicator will go dark and you
will return to the previous screen.
When you enter Sampling mode from Song mode or Pattern mode, the following new f
unctionality is now available.
- The setting "sample+note" has been added as a Recording Type. (p.244)
If you select "sample+note" as the recording type, a note data event to play the
recorded sample will automatically be created when sampling ends.
- The setting "meas" (measure) has been added as a Trigger Mode. (p.246)
This enables the Punch In/Out parameter located below Trigger Mode. If you selec
t "meas" as the trigger mode, sampling will automatically start when the Song or
Pattern playback reaches the specified punch-in measure, and sampling will auto
matically end when the Song or Pattern reaches the specified punch-out measure.
In the File mode Save operation (p.279) when you open the Input Character screen
, the name of the currently selected file will now appear as the default in the
editing area (p.82).
-This is more convenient, since if you have selected a file ahead of time, you w
on't need to enter the entire name of the file to save it.
Voice mode
-In the Voice Play mode's Favorite Voice Select screen (Owner's Manual page.89),
the screen now shows only Main Category 1 and Sub Category 1.
Song mode / Pattern mode
-If you move from the Song Chain screen (Owner's Manual page.185) to the Track V
iew screen (Owner's Manual page.181) etc., the [TRACK] button indicators will no
w light.
-In the Song Edit mode and Pattern Edit mode screens, you can now edit the veloc
ity of a note event by using the [SF6] NUM button.
Pattern mode
-In the Realtime Loop Remix screen (Owner's Manual page.217), you can now select
the track.
Solved problems;
Voice mode
-The problem in which executing Initialize (Owner's Manual page.133) in the Voic
e mode had caused parameter changes to be transmitted via MIDI has been correcte
d.
Song mode / Pattern mode / Mixing mode
-When song recording is stopped, the song location (playback position) will now