Beruflich Dokumente
Kultur Dokumente
Timo Rantanen
HDO701
29.6.2006
1(4)
Front panel user interface with LCD display, keyboard and status LEDs
Remote control of all adjustments by SNMP
Fully compatible with Commander and EMS software SNMP versions
Monitoring of:
drive level
RF input level, optical output power
laser bias current
TEC current
internal temperature and internal supply voltages
Monitoring and control of:
Optical output power (ON / OFF)
Drive level (optical modulation depth)
Gain control mode (AGC or manual)
SBS threshold setting
Channel allocation selection (6, 7 or 8 MHz spacing) for CSO
performance optimisation and wavelength
Product specification
Timo Rantanen
29.6.2006
HDO701
2(4)
Technical specifications
Parameter
Specification
Note
Optical parameters
Wavelength - standard option
Wavelength - DWDM option
Output power - standard option
Output power - high power option
Optical line width
Relative intensity noise
SBS suppression threshold
OMI @ 1 ch
Number of optical outputs
15555 nm
1547.721558.98 nm
2 x 8.5 dBm
2 x 10.0 dBm
300 kHz
-160 dBc/Hz
+13 +19 dBm
4.1 %
2
1)
2)
3)
3)
4)
5)
6)
7)
8)
RF parameters
Frequency range
Input level
Flatness
RF impedance
RF input return loss
Spurious beats
Test point
471000 MHz
80 dBV
0.5 dB
75
20 dB
-60 dB
See note
9)
10)
11)
12)
13)
53 dB
65 dB
65 dB
14)
15)
16)
50 dB
65 dB
63 dB
17)
18)
19)
60 W
100240 VAC / 5060 Hz
IEC female
RJ-45
SC/APC
19 / 1 RU
10 kg
EN 50083-2
IP21
-10...+50 C
-20...+60 C
085%
20)
21)
General
Power consumption
Supply voltages
Connectors, RF
Management interface
Optical
Dimensions
Weight
EMC compliance
Enclosure classification
Operating temperature range
Storage temperature range
Operating relative humidity
22)
23)
Product specification
Timo Rantanen
HDO701
29.6.2006
3(4)
Notes
1) This is a variation range between various transmitters.
2) ITU DWDM channels 37, 36, ..., 23 @ 100 GHz spacing.
3) Minimum value.
4) Typical line width of the source laser.
5) This is a typical value. The maximum value is -158 dBc/Hz.
6) A user can select the SBS suppression threshold. Typical SBS and launch power settings are:
<70 km @ +16 dBm, <80 km @ +15 dBm, <90 km @ +14 dBm and >90 km @ +13 dBm.
7) This is the typical OMI for CENELEC 42 chs channel allocation. The minimum value is 3.9 %.
8) Only one output can be used for super trunking when the distance is more than 65 km. However
the second output is available for local distributing.
9) The build-in AGC circuit provides the optimum drive level to the modulator. The input level
range is 7682 dBV.
10) This is a typical value up to 862 MHz. The maximum flatness error generated by the transmitter
is 0.75 dB (47...862 MHz) and 1.5 dB (8621000 MHz).
11) This is a minimum value at 47 MHz. However the minimum value is reduced by 1.5 dB / octave
on the frequency scale. The absolute minimum is still always 15 dB.
12) Maximum value.
13) The test point is located in the input of the transmitter and the attenuation is 20 dB.
14) Typical value. The minimum value is 52.5 dB.
The C/N influence of the optical input power of a receiver can be seen in the following example.
The fibre link consists of
- HDO701 transmitter, +16 dBm SBS suppression setting
- DVO716 S fibre amplifier
- Fibre 4060 km + optical attenuation, total 1419 dB optical
- Fibre optic CATV receiver (BXO, DXO, DVO, HDO, AC8000 etc.)
C/N vs. link attenuation
54
C/N
53
52
51
50
2
-1
-2
-3
Product specification
Timo Rantanen
HDO701
29.6.2006
4(4)
C/N
51
50
49
9