Beruflich Dokumente
Kultur Dokumente
Index
1.General Information .................................................................................................................3
2. Materials ......................................................................................................................................3
3. Elevations Architectural Drawings .........................................................................................4
4. Design Criteria ............................................................................................................................8
4. Fem Models For Facades Framing .........................................................................................8
4.1 Type 1 Panel System Analysis ............................................................................................8
4.1.1 Design Section Properties .........................................................................................11
4.1.2 Wind Loads and Dead Loads ..................................................................................14
4.1.3 Deformed shape under wind and dead load .....................................................14
4.1.4 Moment Diagram of Members ................................................................................16
4.2 Type 2 Panel System Analysis ..........................................................................................18
4.2.1 Design Section Properties .........................................................................................21
4.2.2 Wind Loads and Dead Loads ..................................................................................24
4.2.3 Deformed shape under wind and dead load .....................................................24
4.2.4 Moment Diagram of Members ................................................................................26
4.3 Type 3 Panel System Analysis ..........................................................................................28
4.3.1 Design Section Properties .........................................................................................31
4.3.2 Wind Loads and Dead Loads ..................................................................................34
4.2.3 Deformed shape under wind and dead load .....................................................34
4.3.4 Moment Diagram of Members ................................................................................37
5.References .................................................................................................................................39
Analysis Report
10 March 2015
1.General Information
Structural Calculations are made according to the EN BS 8118 standard. According to
the technical specification,
The Uniform wind pressure: 3 kN/m2 for design. Maximum deflection: 1/200 of clear
span any framing member.
Extrusions of Bars, Rods and Tubes: 6060-T66 Alloy comforming to ASTM B 221
The Design method is finite elements method for aluminum framing member
2. Materials
Aluminum frame members are 6060-T6 alloy for facades.
ASTM B 221 Standart
Analysis Report
10 March 2015
Analysis Report
10 March 2015
Analysis Report
10 March 2015
Analysis Report
10 March 2015
Analysis Report
10 March 2015
4. Design Criteria
The design wind speed taken from the technical specification that is 3 kN/m2. System
Structural elements self-weight and 12mm glass thickness , load like distributed load that is
0,5kN/m2. Design material is Aluminum materil that is En-AW 6060-T66.
Shell elements have been identified for wind loads installation only. they have never
been accepted as a diaphragm or structural.
Analysis Report
10 March 2015
Model grids defining , Check for width and levels from this table. f you want to change, you
have to consult to Engineer.
Analysis Report
10 March 2015
Analysis Report
10 March 2015
10
Analysis Report
10 March 2015
11
Analysis Report
10 March 2015
12
Analysis Report
10 March 2015
13
Analysis Report
10 March 2015
14
Analysis Report
10 March 2015
15
Analysis Report
10 March 2015
16
Analysis Report
10 March 2015
17
Shell elements have been identified for wind loads installation only. they have never
been accepted as a diaphragm or structural.
Analysis Report
10 March 2015
18
Model grids defining , Check for width and levels from this table. f you want to change, you
have to consult to Engineer.
Analysis Report
10 March 2015
19
Analysis Report
10 March 2015
20
Analysis Report
10 March 2015
21
Analysis Report
10 March 2015
22
Analysis Report
10 March 2015
23
10 March 2015
24
Analysis Report
10 March 2015
25
Analysis Report
10 March 2015
26
Analysis Report
10 March 2015
27
Shell elements have been identified for wind loads installation only. they have never
been accepted as a diaphragm or structural.
Analysis Report
10 March 2015
28
Model grids defining , Check for width and levels from this table. f you want to change, you
have to consult to Engineer.
Analysis Report
10 March 2015
29
Analysis Report
10 March 2015
30
Analysis Report
10 March 2015
31
Analysis Report
10 March 2015
32
Analysis Report
10 March 2015
33
Analysis Report
10 March 2015
34
Analysis Report
10 March 2015
35
Analysis Report
10 March 2015
36
Analysis Report
10 March 2015
37
Analysis Report
10 March 2015
38
5.References
-
Analysis Report
10 March 2015
39