Sie sind auf Seite 1von 7

SAMSUNG ENGINEERING CO.

, LTD
SAMSUNG SEI TOWER, 467-14 Dogok 2 Dong,
Kangnam-Ku, Seoul, KOREA 135-280

DESIGN MANUAL
SEM-9518E
PROCESS DESIGN MANUAL

Preparation of Datasheet
for Truck Scale
REV.
DATE

:0
: 2006.8.23

SAMSUNG ENGINEERING CO., LTD.

DATE : 2006. 8. 23

DESIGN MANUAL

SEM 9518E

Preparation of Datasheet

REV. : 0

for Truck Scale

PAGE i OF i

CONTENTS
Page
1

GENERAL................................................................................................1

SHEET NO. AND REVISION NO.............................................................1

PROJECT INFORMATION......................................................................1
3.1
3.2

OPERATING CONDITIONS.....................................................................2
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8

SUPPLIER.......................................................................................1
NO. REQD.....................................................................................1

TYPE..............................................................................................2
CAPACITY.......................................................................................2
MIN. GRADUATION..........................................................................2
ACCURACY.....................................................................................2
TEMPERATURE RANGE....................................................................2
PLATFORM DIMENSION....................................................................3
INSTALLATION.................................................................................3
MEASURING DISPLAY......................................................................3

CONSTRUCTION.....................................................................................3
5.1
5.2

RECORDING SYS............................................................................3
ATTACHMENTS................................................................................4

MATERIALS.............................................................................................4

ACCESSORIES........................................................................................4

REVISION HISTORY................................................................................5

DESIGN MANUAL

SEM 9518E

Preparation of Datasheet

REV. : 0

for Truck Scale

PAGE 1 OF 5

DATE : 2006. 8. 23

GENERAL
This is guideline for how to fill up the truck scale data sheet.
The truck scale is equipment to measure when goods are warehoused
or delivered from the warehouse. This equipment is simple, so its
structure and properties may be specified sufficiently with only the data
sheet. You may refer to this guide to fill in the data sheet.

SHEET NO. AND REVISION NO.


For revision, it shall be marked as Revision 0 in the initial issue. Every
time, the revision of the concerned data sheet is generated, revision
shall be entered in step, such as 1, 2, 3, and the revision method
shall apply the DWG method.

PROJECT INFORMATION
Customer's name shall be entered in full name, if possible, and area and
country name shall be entered for location. For service, the concerned
system or process shall be entered. For Req'N No. it shall be entered as
follow up after Req'N is issued, because it needs to be entered when
Req'n is issued by the Machine Team.
3.1

Supplier
As a supplier is decided after a purchase contract of the
equipment is made, it shall be indicated by checking it when 1st
phase vendor print is accepted.

3.2

No. Reqd
Required number and unit of the equipment shall be entered.

DESIGN MANUAL

SEM 9518E

Preparation of Datasheet

REV. : 0

for Truck Scale

PAGE 2 OF 5

DATE : 2006. 8. 23

OPERATING CONDITIONS
4.1

Type
Type refers to the shape of the truck scale platform installed, and
is classified into a pit type and a pit less type. The pit type is to
install the platform to be aligned with ground level, which is
applied to narrow turning area of a truck.
The pit less type is to install the platform above ground level,
which is applied when the turning area of a truck is sufficient.

4.2

Capacity
Capacity is decided depending on the capacity of a truck, and is
decided by the owner's in general.
The marking of capacity is good to mark in line with the capacity
of a truck, but, KG shall be entered on the data sheet, because
the truck capacity marking method is diverse.

4.3

Min. Graduation
This is to indicate minimum measurement of the scale, and is
indicated as the unit of positive number. The marking is carried
out like 1KG, 10KG, etc.

4.4

Accuracy
This is to enter the error of the scale, and the marking method is
like this: 1/2500, 1/3000

4.5

Temperature Range
This is to enter air temperature. The air temperature is closely
associated with the error of the scale. For this reason, air

DESIGN MANUAL

SEM 9518E

Preparation of Datasheet

REV. : 0

for Truck Scale

PAGE 3 OF 5

DATE : 2006. 8. 23

temperature shall be essentially recorded.


4.6

Platform Dimension
It is better to decide by checking the length and width of a truck
in terms of platform. However, if decision is difficult, write down
the standard size on the data sheet in reference of vendor
catalogue, and the dimensions shall be revised with confirmed
size later on.

4.7

Installation
Insulation generally indicates the locations of platform and local
board, and insulation shall be decided in reference of general
plot plan. Especially, insulation shall be entered by checking
whether or not it is related to hazardous area.

4.8

Measuring Display
This indicates display methods, and a digital method is usually
used.

CONSTRUCTION
5.1

Recording Sys.
This is about recording method, and shall be decided in
consultation with the owner.
5.1.1

Type
This refers to how to use paper for record, and one
method of three methods card insert method, continuous
paper roll system, and paper cut each time shall be

DESIGN MANUAL

SEM 9518E

Preparation of Datasheet

REV. : 0

for Truck Scale

PAGE 4 OF 5

DATE : 2006. 8. 23

selected. The selection of the method about how to use


paper for record shall be decided in consultation with the
owner.
5.1.2

Continuous of Recording
This refers to matters to be recorded on the paper for
record. Basically, date, serial number, tare weight, net
weight, and gross weight shall be recorded.

5.1.3

Recording Operation
This refers to how to operate equipment when recording
matters on the paper for record. An electronic type and a
manual type shall be selected.

5.2

Attachments
Attachments refer to accessories mounted on the display, and
shall be used selecting from the data sheet.

MATERIALS
These indicate the materials of structures of the truck scale.
SS41 is used for the material of platform and support.

ACCESSORIES
Accessories include local display, computer system, pit pump, printer
cards, rolled paper, ribbon for print, damping oil, fuse, and test weight.
Local display refers to install outside of the gate house or around truck
scale platform. Local display shall be installed where truck drivers or
operators may see it.
Computer system is the system to install enabling control of the status of

DESIGN MANUAL

SEM 9518E

Preparation of Datasheet

REV. : 0

for Truck Scale

PAGE 5 OF 5

DATE : 2006. 8. 23

warehousing and delivery from warehouse in the DCS.


Pit pump is applied to pit type among the truck scale types. Location is
needed to be careful. Printer cards, rolled paper, ribbon for print,
damping oil, and fuse are spare parts, and it's better to get checked by
the owner.
Test weight is concerned with scope of supply, but the supply relations
are needed to be checked by the owner.
8

REVISION HISTORY
Rev

Date

Page

06.08.23

All

Revision Status
- Team : Process Eng'g Team
- Made by : M.H. Lee
- Checked by : J.C. Ro, E.D. Lee, Henry Sung, B.S. Son
- Approved by : C.S. Jung

Das könnte Ihnen auch gefallen