Beruflich Dokumente
Kultur Dokumente
2015-8-4
Huawei Confidential
Confidentiality
Level
Page 1 of 68
Confidentiality
Level
Product Name
Confidentiality Level
BTS3900
INTERNAL
Product Version
Total 43 Pages
Prepared by
Date
Reviewed by
Date
Approved by
Date
2011-03-04
2015-8-4
Huawei Confidential
Page 2 of 68
Confidentiality
Level
Change History
Date
2011-04-29
2015-8-4
Revision
CR
Section
Version
ID
Number
Description
Draft completed
Huawei Confidential
Author
Li Lijun
Page 3 of 68
Confidentiality
Level
Content
1
Huawei Confidential
Page 4 of 68
Confidentiality
Level
3.29.4
Tracing CS Signaling over the Abis Interface..................................................49
3.29.5
Tracing PS Signaling over the Abis Interface..................................................52
3.29.6
Tracing CS Signaling of a Single User.............................................................52
3.29.7
Tracing PS Signaling of a Single User.............................................................53
Performing Related Operations................................................................................................55
4.1
Performing Loopback Tests..........................................................................................55
4.1.1
Performing Interface Board Port Timeslot Loopback......................................55
4.1.2
Performing BTS Voice Loopback.....................................................................56
4.1.3
Performing TRX Voice Loopback....................................................................57
4.1.4
Performing BIU Loopback...............................................................................58
4.2
Modifying the BTS Soft Parameters............................................................................60
4.3 Reducing the Interference Band Software Parameters.......................................................60
2015-8-4
Huawei Confidential
Page 5 of 68
Confidentiality
Level
Alarm log
Operation log
Configure files
PMF
2015-8-4
Huawei Confidential
Page 6 of 68
1.1
Confidentiality
Level
You can run the LST OMUAREA command to query the workspace of the OMU and the current
running version.
1.2
Accessing the OMU by using the File Manager on the Web LMT
Note:
The File Manager can show a maximum of 1,000 pieces of data. If the number of files in the
directory exceeds 1,000, some log files may not be displayed. Therefore, you must use other
methods to obtain required information.
2015-8-4
Huawei Confidential
Page 7 of 68
Confidentiality
Level
2 Basic Operations
2.1
(1) Start the BSC6900, enter the super user mode, and click About.
2015-8-4
Huawei Confidential
Page 8 of 68
Confidentiality
Level
(3) Choose Device Maintenance > BTS Maintenance > Internal Maintenance > Custom
Message.
(4) The Custom Message window is displayed. Specify Site and Message Type.
2015-8-4
Huawei Confidential
Page 9 of 68
Confidentiality
Level
(5) Send a transparent transmission command of a custom message. The custom message may be
as follows:
D4-00-FF-FF-FF-81-00-FF-01-35
2015-8-4
Huawei Confidential
Page 10 of 68
Confidentiality
Level
(2) Run the LST GTRX command to query the TRX number
2.2
(1) Click About at the upper right corner of the BSC LMT.
2015-8-4
Huawei Confidential
Page 11 of 68
Confidentiality
Level
(3) Click BTS Maintenance and choose Internal Maintenance > COM Redirection.
2015-8-4
Huawei Confidential
Page 12 of 68
Confidentiality
Level
(4) On the COM Redirection page, specify Site and set Message Type to Transparent.
2015-8-4
Huawei Confidential
Page 13 of 68
Confidentiality
Level
(5) In the Custom Message text box, send a redirStart message to redirect the COM port of the
TMU. An OK dialog box is displayed.
(7) Send the following two messages to redirect the COM port of the RRU.
iSend2TrxShell "redirStart",0
iSend2TrxShell "redirRestart",0
(8) Right-click a target board and choose Query Board Information from the shortcut menu to
query the board number.
2015-8-4
Huawei Confidential
Page 14 of 68
Confidentiality
Level
2015-8-4
Huawei Confidential
Page 15 of 68
Confidentiality
Level
(1) Run the STR BTSLOG command to obtain the BTS log. Specify BTS Index and set Board
Type to TMU(TMU/DTMU).
(2) After the command is executed completely, click File Manager, choose a log file from the
directory
\\bam\version_a\ftp\bts\btscmplog
(When
BSC6900
version
is
R11)
or
3.2
(1) Run the STR BTSLOG command to obtain log information and specify BTS Index, Board
2015-8-4
Huawei Confidential
Page 16 of 68
Confidentiality
Level
(2) After the command is executed completely, click File Manager, choose a log file from the
directory \\bam\version_a\ftp\bts\btscmplog, and click Download.
3.3
(1) Run the STR BTSLOG command to obtain log information and specify BTS Index, Board
Type, and Board No. Here, set Command Parameter to mfs:/GSMLOG/GSMLOGS.lps.
(2) After the command is executed completely, click File Manager, choose a log file from the
directory \\bam\version_a\ftp\bts\btscmplog, and click Download.
2015-8-4
Huawei Confidential
Page 17 of 68
3.4
Confidentiality
Level
(1) Run the EXP CFGMML command to export the current configuration file.
(2)
Click
File
Manager,
choose
log
file
from
the
directory
2015-8-4
Huawei Confidential
Page 18 of 68
Confidentiality
Level
Note:
The rules for naming files (if no file name is specified) are as follows:
For example: CFGMML-BSC0-20091202184237.zip
CFGMML BSC0 2009 12 02 18 42 37 .zip
CFGMML + BSC0 + year + month + day + hour + minute + second + suffix of the file name
3.5
2015-8-4
Huawei Confidential
Page 19 of 68
(2)
Click
File
Manager,
choose
log
file
Confidentiality
Level
from
the
directory
3.6
(1) On the Web LMT, click Alarm, specify Alarm Type and Alarm Severity, and set Return
Amout to 4000 and Filter By BTS to a target site. Then, click Query.
2015-8-4
Huawei Confidential
Page 20 of 68
Confidentiality
Level
(2) After the alarms are filtered successfully, right-click an alarm and choose Save All from the
shortcut menu to save the result in the .csv format.
3.7
(1) Run the COL LOG command and set Log File Type to OPT_LOG.
2015-8-4
Huawei Confidential
Page 21 of 68
Confidentiality
Level
The rules for processing time are as follows: If Start Time and End Time are not set, logs
recorded from the earliest time to the latest time are exported by default. If Start Time is set but
End Time is not set, all logs recorded from the start time to the latest time are exported. If Start
Time is not set but End Time is set, logs recorded from the earliest time to the end time are
exported.
(2)
Click
File
Manager
and
find
the
OperateLog.zip
file
from
the
directory
\\bam\version_a\ftp\COLLOGINFO\OPT-LOG\.
2015-8-4
Huawei Confidential
Page 22 of 68
3.8
Confidentiality
Level
Click File Manager and obtain the traffic measurement file from the directory
\\bam\common\MeasResult.
minutes or 60 minutes
A20100915.0300+0800-0400+0800_EMS-NORMAL.mrf.bz2
A20101126.1330+0800-1400+0800_EMS-NORMAL.mrf.bz2
2015-8-4
Huawei Confidential
Page 23 of 68
Confidentiality
Level
3.9
Run the SET GCELLSOFT command to enable the single pass check function and specify
parameters.
Click
2015-8-4
File
Manager.
The
single
pass
Huawei Confidential
log
is
stored
in
the
directory
Page 24 of 68
Confidentiality
Level
(2) The following table lists the formats for recording log file names:
Item
Serial
Number
Total number of frames checked during the primary single pass check
Site number, cell number, TRX number, and channel number of the call
Phone number (or TMSI/IMSI) being called and phone number (or TMSI/IMSI) of the peer party (record the
called number and the TMSI or IMSI information of the calling MS when the current call is an outgoing call;
record the calling number and the TMSI and IMSI information of the called MS when the current call is an
incoming call), and record the phone number and IMSI/TMSI if they exist.
2015-8-4
Huawei Confidential
Page 25 of 68
Confidentiality
Level
1: IP
2: HDLC
9
Subrack number, slot number, port number, timeslot number, and sub timeslot number of the Abis interface
board occupied by the current call, IP address and port of the Abis interface board (recorded if the Abis
interface is based on IP), HDLC port, and sub port (recorded if the Abis interface uses HDLC for
transmission)
10
Subrack number, slot number, port number, timeslot number, and sub timeslot number of the GEIUT of the
BM subrack (not required when the TC subrack and the BM subrack are integrated)
11
Subrack number, slot number, port number, timeslot number, and sub timeslot number of the GEIUT of the
TC subrack (not required when the TC subrack and the BM subrack are integrated)
12
Subrack number, slot number, DSP number, and DSP timeslot number of the DPU
13
14
15
16
Service type
2015-8-4
Huawei Confidential
Page 26 of 68
Confidentiality
Level
(2) Run the DSP BTSNET MML command to query the BTS upper-layer net list, set NET
Object Type to TRX, and choose a target site.
(3) Query the lower-layer net list of the BTS by sending custom messages.
Open the Custom window, set Message Type to Transparent, and send the following
command to transparently transmit custom messages to the remote end:
D4-00-FF-FF-FF-81-00-FF-01-35
Then, send the following custom messages:
D4-00-ff-ff-ff-81-00-ff-05-99-01-00-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-01-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-02-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-03-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-08-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-09-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-0A-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-0B-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-0C-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-0D-00-ff
2015-8-4
Huawei Confidential
Page 27 of 68
Confidentiality
Level
D4-00-ff-ff-ff-81-00-ff-05-99-01-0E-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-0F-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-10-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-11-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-12-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-13-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-14-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-15-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-16-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-17-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-18-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-19-00-ff
D4-00-ff-ff-ff-81-00-ff-05-99-01-1A-00-ff
Save the query results in .txt files and send the files to R&D engineers.
UMRECORDPARA:
TRXID=468,
CHNO=3,
UMRECCMDCODE=STARTREC,
SERVICETYPE=CS,
SUBCHNO=FULLRATEORPDCH,
RECDIR=DLONLY,
RECMAXTIME=20;
(2) After the recording is completed, run the SET UMRECORDPARA command and specify
UMRECCMDCODE to STRULDRECDATA. View the progress, and after the progress reaches
100%, perform Step 3. An example of the command is as follows:
SET UMRECORDPARA: UMRECCMDCODE=STRULDRECDATA, TRXID=468;
(3) Run the STR BTSLOG command, set Log Type to CMPLOG and Index Type to BYID, and
enter mfs:/DSPTRAU in Command Parameter. View the progress, and after the progress
reaches 100%, perform Step 4.
2015-8-4
Huawei Confidential
Page 28 of 68
Confidentiality
Level
(5) After all the preceding steps are completed, search the path \\mbsc\bam\version_a or
version_b)\ftp\bts\log\btscmplog for compressed logs whose names are similar to the name of
the recording BTS.
(6) Run the RMV CALLRESRECORD command to delete all records.
RMV CALLRESRECORD: RECINDEX=0;
UMRECORDPARA:
UMRECCMDCODE=STARTREC,
SERVICETYPE=PS,
EDATE=2011&07&15,
ETIME=18&15&38,
BRDTYPE=GRRU,
BRDNO=1, SUBCMD="mfs:/DSPTRAU";
6Collect log file
After all the preceding steps are completed, search the path \\mbsc\bam\version_a or
2015-8-4
Huawei Confidential
Page 29 of 68
Confidentiality
Level
version_b)\ftp\bts\log\btscmplog for compressed logs whose names are similar to the name of
the recording BTS.
CALLRESRECORD:
RECINDEX=0,
MSISDN="13908881006", RECORDTYPE=TC;
ADD
CALLRESRECORD:
(calling party)
RECINDEX=1,
MSISDN="13908881005", RECORDTYPE=TC;
USERIDTYPE=BYMSISDN,
USERIDTYPE=BYMSISDN,
(called party)
Note:
All commands of the function are internal commands and are not described in the help document.
The value of RECINDEX ranges from 0 to 5. Each added recording point is identified by a
2015-8-4
Huawei Confidential
Page 30 of 68
Confidentiality
Level
unique index.
USERIDTYPE includes four values, as described in the following table:
TMSI
IMSI
IMEI
Note:
Because recording of up to four MSs can be performed simultaneously under the BSC, the value
of RECINDEX ranges from 0 to 3. If the message "The data to be added conflicts with the
existing data" is displayed when the command is executed, it indicates that the number of
recording MSs reaches the maximum value. In this case, you can run the following command to
2015-8-4
Huawei Confidential
Page 31 of 68
Confidentiality
Level
condition)
(2) Perform dialing tests and call tests. After all call tests are completed, extract the TC recording
file from the directory \\mbsc\bam\common\fam\tc_file.<0
2015-8-4
Huawei Confidential
Page 32 of 68
Confidentiality
Level
2 Specify parameters in the Configure Frequency Scan window and click Start to perform
the test. Note:
The start time must be later than the current time; otherwise, the test cannot be performed.
2015-8-4
Huawei Confidential
Page 33 of 68
Confidentiality
Level
(3) After the configuration is successful, right-click the tested cell and choose Query Frequency
Scan from the shortcut menu. Then, choose the names of the tested site and cell. Note:
Open the Query Frequency Scan window immediately after the frequency configuration is
successful, and then wait for the query results; otherwise, the query results cannot be reported.
2015-8-4
Huawei Confidential
Page 34 of 68
Confidentiality
Level
(4) Observe the query results. After the results are reported, record the data of each frequency,
press Ctrl + A to select all, press Ctrl + C to copy the data, and paste the data to an excel file.
Note:
The reporting time is long and may take 56 minutes.
2015-8-4
Huawei Confidential
Page 35 of 68
Confidentiality
Level
TST BTSPERF:IDTYPE=BYID,BTSID=140,TRXID=1148;
NOTE:This is a inner command and some BSC version dont support.So if it dont work,please
use customer message to query.
2015-8-4
Huawei Confidential
Page 36 of 68
Confidentiality
Level
2 By using the method described in section 2.1, open the Custom Message window and
send the following message:
D4-00-FF-FF-FF-81-00-FF-01-35
(3) Send the following custom messages according to TRX types:
(1) When the module type is Mrfu v1, send the following custom messages:
Common cell:
Forward power (before compensation):
D4-04-cell number-TRX number-FF-90-00-0c-87-TRX number-09-16-C4-00-F0-80-12-10-00-04
(2) When the module type is Mrru 900m/1800m v1, send the following commands:
Common cell:
Forward power over channel A (after compensation):
2015-8-4
Huawei Confidential
Page 37 of 68
Confidentiality
Level
Co-cell:
Forward power over channel A (after compensation):
D4-04-cell number-TRX number-FF-91-00-0c-87-board number-09-16-C4-00-F0-00-00-31-00-03
(3) When the module type is Mrfu v2, send the following commands:
Common cell:
Forward power (before compensation):
D4-04-cell number-TRX number-FF-90-00-0c-87-TRX number-09-16-C4-00-F0-00-8c-02-00-04
2015-8-4
Huawei Confidential
Page 38 of 68
Confidentiality
Level
Co-cell:
Forward power (before compensation):
D4-04-cell number-TRX number-FF-91-00-0c-87-board number-09-16-C4-00-F0-00-8c-02-00-04
2015-8-4
Huawei Confidential
Page 39 of 68
Confidentiality
Level
(2) Click Start to view the interference band and send a snapshot to R&D engineers.
Huawei Confidential
Page 40 of 68
Confidentiality
Level
(2) Run the DSP BTSELABEL command to query the bar code of the TMU board.
2015-8-4
Huawei Confidential
Page 41 of 68
Confidentiality
Level
If the obtained bar code contains HNK, the GTMU A board is queried. If the obtained
bar code contains LPM, the GTMU B board is queried.
BarCode=030LPM4MA6222046
board B
BarCode=030HNK1083000149
board A
MRRU.HUAWEI.CS2420100
Hardware version
MRRU.HUAWEI.x4A120002
Note:
In special cases, the hardware version in the running parameters of the MRRU V1
1800M module is displayed as "x3".
In conclusion, when the hardware version in the running parameters of the MRRU
module is displayed as "x3", the MRRU module can be confirmed as a V1 1800M
module.
(2) Run the DSP BTSELABEL command to query the RRU V1/V2 module. If the
module version is V2, the following information in red is displayed. If the module
version is V1, no information is displayed.
Description=DBS3900,WD5MJRUAC8E,MRRU V2,Multi-mode Multi-carriers Remote Radio
Huawei Confidential
Page 42 of 68
Confidentiality
Level
3.22 Querying the Mapping Between Internal TRX Number and External TRX
Number
1 Right-click a board on the BTS device panel and choose Query Board
Information from the shortcut menu to query the board number.
2 Run the LST GTRX command to query the external TRX number.
Huawei Confidential
Page 43 of 68
Confidentiality
Level
4 Query the mapping between the internal TRX number and the external TRX
number and send the following command on the COM Redirection page:
iSend2TrxShell "RRM_vShowTrxBindInfo",0 (0 is the board number)
The printed results are as follows:
Note:
ucTrxno indicates the external TRX number, and ucTrxIndex indicates the internal TRX number
(2) After the command is executed completely, click File Manager, choose a log file from the
directory \\bam\version_a\ftp\bts\btscmplog, and click Download.
2015-8-4
Huawei Confidential
Page 44 of 68
Confidentiality
Level
(2) After the command is executed completely, click File Manager, choose a log file from
the directory \\bam\version_a\ftp\bts\btscmplog, and click Download.
Note:
If a time-out occurs, resend the message. Send the printed message in the window to R&D
engineers.
2015-8-4
Huawei Confidential
Page 45 of 68
Confidentiality
Level
Note:
If a time-out occurs, resend the message. Send the printed message in the window to R&D
engineers.
2015-8-4
Huawei Confidential
Page 46 of 68
Confidentiality
Level
2015-8-4
Huawei Confidential
Page 47 of 68
Confidentiality
Level
Board
Information you
Information appear
can
query
the
Version
the
following
NO.
in
picture,
Software
selectBasic
version,
For
example:V100R012C00SPC039
2015-8-4
Huawei Confidential
Page 48 of 68
Confidentiality
Level
Board Informationappear the following picture, select Running Parametersyou can query
the Internal Version NO. in Software version, For example: 13.394.10.009.
//0is BTSID
2015-8-4
\\bam\version_a\ftp\export_cfgmml.
Huawei Confidential
Page 49 of 68
Confidentiality
Level
You can trace the A interface BSSAP message, A interface MTP3 message, A
interface MTP2 message, A interface SCCP message, A interface SCTP message, and
A interface M3UA message.
Click Trace on the LMT to open the Trace tab. In Trace Navigation Tree,
choose Trace > GSM Services and double-click A Interface Trace.In the A
Interface Trace dialog box, specify parameters on the Basic tab, then specify
parameters on the tab corresponding to the type of the signaling to be traced, and click
Submit. The traced message is displayed.
2015-8-4
Huawei Confidential
Page 50 of 68
Confidentiality
Level
You can trace layer-3 signaling messages on the CS Um interface and trace the messages by
TRX and cell. You can trace the Um interface messages in up to 16 cells.
Click Trace on the LMT to open the Trace tab. In Trace Navigation Tree, choose Trace
> GSM Services and double-click Um Interface CS Trace. In the Um Interface CS Trace
dialog box, specify parameters and click Submit.The traced message is displayed.
2015-8-4
Huawei Confidential
Page 51 of 68
Confidentiality
Level
You can trace various PS Um interface messages, including the DUMMY message, system
message, dummy paging message, and data block message.
Click Trace on the LMT to open the Trace tab. In Trace Navigation Tree, choose Trace
> GSM Services and double-click Um Interface PS Trace.In the Um Interface PS Trace dialog
box, specify parameters and click Submit.The traced message is displayed.
2015-8-4
Huawei Confidential
Page 52 of 68
Confidentiality
Level
You can trace various CS Abis interface signaling messages, including the Abis interface RSL
message, Abis interface ESL message, Abis interface EML message, Abis interface OML message,
and Abis interface LAPD message.
2015-8-4
Huawei Confidential
Page 53 of 68
Confidentiality
Level
Click Trace on the LMT to open the Trace tab. In Trace Navigation Tree, choose Trace >
GSM Services and double-click Abis Interface CS Trace. In the Abis Interface CS Trace
dialog box, specify parameters on the Basic tab, then specify parameters on the tab
corresponding to the type of the signaling to be traced, and click Submit. The traced
message is displayed.
(1) The following figures show the process of tracing OML messages:
2015-8-4
Huawei Confidential
Page 54 of 68
Confidentiality
Level
(2) The following figures show the process of tracing RSL messages:
2015-8-4
Huawei Confidential
Page 55 of 68
Confidentiality
Level
2015-8-4
Huawei Confidential
Page 56 of 68
Confidentiality
Level
If you set Trace Object Symbol Type to MSISDN, you must set MSISDN to the peer number.
(1) (Recommended) If the calling user is traced, MSISDN indicates the called number. For
example, if the user dials 12345, MSISDN must be set to 12345.
(2) If the called user is traced, MSISDN indicates the calling number. For example, if the
calling number displayed on the called MS is 54321, MSISDN must be set to 54321.
If you set Trace Object Symbol Type to TMSI or IMSI, you must confirm the reallocation
policy of the MSC as follows:
(1) If the MS initiates a TMSI call, the TMSI tracing function can be enabled.
(2) If the MS initiates an IMSI call, the IMSI tracing function can be enabled.
If you set Trace Object Symbol Type to IMEI, you must confirm whether the MSC has enabled
the function of obtaining the IMEI.
Huawei Confidential
Page 57 of 68
Confidentiality
Level
GSM Services and double-click Single User PS Trace. In the Single User PS Trace dialog box,
specify parameters and click Submit.The traced message is displayed.
You can choose Trace Um Datablock Message only when Trace Interface Type is set to
UM Interface. If you set Trace Object Symbol Type to IMSI, you must confirm the reallocation
policy of the MSC: If the MS initiates an IMSI call, the IMSI tracing function can be enabled.
If you set Trace Object Symbol Type to TLLI, you must first run the DSP MSCONTEXT
command to view the TLLI value of the MS that is in the PS service process. When the MS is in
the PS service process, the TLLI may be reallocated. In this case, you can continue the query to
obtain a new TLLI and continue the tracing.
2015-8-4
Huawei Confidential
Page 58 of 68
Confidentiality
Level
4.1.1
You can perform interface board port timeslot loopback on any one of the following boards:
GE(O)IUA, GE(O)IUB, GE(O)IUT, and GE(O)IUP. There are two loopback modes: remote
loopback and local loopback.
Remote loopback: The signal received in the timeslot is not processed but directly sent out in
the TX direction of the timeslot. During the loopback, the interface board still continues to receive
the signal sent in the timeslot.
Local loopback: The signal that needs to be sent in the timeslot is not sent out but directly
taken back in the RX direction of the timeslot. During the loopback, the interface board still
continues to receive the signal sent in the timeslot.
Abis interface board timeslot loopback is frequently used in voice troubleshooting. A
interface timeslot loopback can be replaced by external voice loopback.
The procedure for performing interface board port timeslot loopback is as follows:
(1) Click Device Maintenance, choose BSC Maintenance > Interface Board Port Timeslot
Loopback, and specify Subrack No. and Slot No.
(2) Click Query, select the timeslot number to be looped back, and click Start.
2015-8-4
Huawei Confidential
Page 59 of 68
Confidentiality
Level
Note:
During the Abis /Ater interface board timeslot loopback, you must set the loopback timeslot
correctly. You can calculate the E1 timeslot by using the timeslot queried in section 3.24 "Single
User Resource Check".
4.1.2
You can perform the BTS voice loopback test on a traffic channel to verify whether the voice
channel of the TRX from the air interface to the internal DBUS of the BTS is connected normally.
During the test, the TMU board loops back the DBUS timeslot corresponding to the tested voice
channel and the connection can be checked according to whether the users occupying the channel
can hear their own voices. If the users can hear their own voices, the connection is normal;
otherwise, the connection is abnormal.
After a voice problem such as noise occurs, a BTS voice loopback test can be performed. If
the users can hear noise, the voice problem may be located in the downlink direction of the Abis
interface; otherwise, the voice problem is located in the uplink direction of the Abis interface.
The procedure for performing BTS voice loopback is as follows:
(1) Click Device Maintenance, choose BTS Maintenance > Maintain TRX > Test Channel
2015-8-4
Huawei Confidential
Page 60 of 68
Confidentiality
Level
Loopback, specify Site, Cell, TRX No., and Channel, and set Test Project to BTS Voice Loop
Test.
(2) Read the three precautions in Description, specify Duration, and click Start to perform the
test.
Note:
You can set TRX No. and Channel to the TRX number and channel number queried in section
3.24 "Single User Resource Check".
4.1.3
You can perform the TRX voice loopback test on a traffic channel to verify whether the voice
channel of the TRX from the air interface to the codec of the baseband DSP is connected normally.
During the test, the baseband DSP directly encodes the decoded data of the traffic channel and
sends the data out, and the connection can be checked according to whether the users occupying
the channel can hear their own voices. If the users can hear their own voices, the loopback is
correct.
2015-8-4
Huawei Confidential
Page 61 of 68
Confidentiality
Level
After a voice problem, such as noise, occurs, a TRX voice loopback test can be performed. If
the users can hear noise, the voice problem may be located in the downlink direction of the DBUS
(and TRX); otherwise, the voice problem is located in the uplink direction of the TRX.
The procedure for performing TRX voice loopback is similar to the procedure for performing
BTS voice loopback. The procedure for performing TRX voice loopback is as follows:
(1) Click Device Maintenance, choose BTS Maintenance > Maintain TRX > Test Channel
Loopback, specify Site, Cell, TRX No., and Channel, and set Test Project to TRX Voice Loop
Test.
(2) Read the three precautions in Description, specify Duration, and click Start to perform the
test.
4.1.4
You can perform the BIU loopback test on only idle channels. On the LMT, choose BTS
Maintenance > Maintain TRX > Test Channel Loopback and specify Site, Cell, TRX No., and
Channel. Set Test Project to BIU Loop Test. Click Start to perform the test. After the test is
2015-8-4
Huawei Confidential
Page 62 of 68
Confidentiality
Level
Note:
You must perform BIU loopback on all channels of the target TRX, four times per channel.
The loopback test results are returned in a table. An example of the loopback test results is listed
as follows:
Loopback Mode/Test MS
MS A at a Problem Site
MS B at a Normal Site
Local
Interface
Interface
Loopback
hear B
BTS Loopback
TRX Loopback
hear B
Abis
Loopback
Remote
Abis
Note:
Prepare the table for recording test results before the test. To ensure the accuracy of test results,
2015-8-4
Huawei Confidential
Page 63 of 68
Confidentiality
Level
4.2
example,
SET GCELLBTSSOFT: IDTYPE=BYID, CELLID=112, ITEMINDEX=39, ITEMVALUE=254;
Note:
Bit 7 of software parameter 56 indicates that the 200K filter switch is used to calculate the
interference band of the MRFU V2. If bit 7 is set to 0, the switch is enabled. If bit 7 is set to
1, the switch is disabled. When the software parameter is used, you need to query the value of
the software parameter before setting the software parameter because each bit has its own
2015-8-4
Huawei Confidential
Page 64 of 68
Confidentiality
Level
meaning. In this way, other function switches will not be affected when this function is
enabled.
LST GCELLBTSSOFT: IDTYPE=BYID, CELLID=Cell index value;
After the bit occupation of the software parameter is determined, set bit 7 to 0 to recalculate
the value of the software parameter.
If the queried value of software parameter 56 is 223, namely 0xDF (corresponding to the
binary code 11011111), bit 5 has been set to 0. In this case, the 200K filter bandwidth switch
BIT7 must be enabled, namely, bit 7 must be set to 0. Therefore, the recalculated value of
software parameter 56 is 0x5F, namely 95.
SET GCELLBTSSOFT: IDTYPE=BYID, CELLID=Cell index value, ITEMINDEX=56,
ITEMVALUE=95;
3> Select an interference band reporting combination algorithm (applicable to all modules
except MRRU V2):
SET GCELLBTSSOFT: IDTYPE=BYID, CELLID=Cell index value, ITEMINDEX=59,
ITEMVALUE=239;
Note:
Bit 5 and bit 4 of software parameter 59 indicate the interference band reporting combination
algorithm. When the two bits are set to 10, it means selecting the average value. When the
two bits are set to 01, it means selecting the minimum value. When the two bits are set to 00
or 01, it means selecting the maximum value. The default value is 11. The following table
shows the details.
BIT5
BIT4
Algorithm
2015-8-4
Huawei Confidential
Page 65 of 68
Confidentiality
Level
4> Set the interference band reduction factor (applicable to all modules except MRRU V2):
SET GCELLBTSSOFT: IDTYPE=BYID, CELLID=Cell index value, ITEMINDEX=19,
ITEMVALUE=255;
Bit 5 to bit 2 of software parameter 19 indicate a reduction factor. The value 1111 is the default
value and the factor is not used.
10101110 are invalid values and can be normalized to 1001, namely, reducing 9 dB. The
following table lists the possible parameter values:
0
0
0
1
0
1
1
0
Meaning
Reducing 0
dB
Reducing 1
dB
Reducing 2
dB
Reducing 3
dB
Reducing 4
Huawei Confidential
Page 66 of 68
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
1
1
0
0
1
1
0
0
1
1
Confidentiality
Level
dB
Reducing 5
dB
Reducing 6
dB
Reducing 7
dB
Reducing 8
dB
Reducing 9
0
1
0
1
0
1
dB
Invalid
Invalid
Invalid
Invalid
Invalid
Invalid
GCELLBTSSOFT:
IDTYPE=BYID,
CELLID=Cell
index
value,
ITEMINDEX=19, ITEMVALUE=204;
Note:
The following command for modifying the IF filter bandwidth affects the performance of the
service and is not recommended when being used to reduce the interference band.
5> Run the following command to modify level-1 filter bandwidth for the MRFU V1/MRRU
V1:
SET GCELLBTSSOFT: IDTYPE=BYID, CELLID=Cell index value, ITEMINDEX=91,
ITEMVALUE=251;
Software parameter 91 is set to 255 by default. For the M series and D series, different bits
are used to configure the IF filter.
The method for configuring IF filters of M series and the meanings of bits are as follows
Bit 0 of software parameter 91 has other purposes. Bit 2 and bit 1 are used to configure the
2015-8-4
Huawei Confidential
Page 67 of 68
Confidentiality
Level
00
01
10
11
Filter
260K
200K
Reserved
260K
bandwidth
6> Run the following command to modify level-1 filter bandwidth for the DRRU/DRFU:
SET GCELLBTSSOFT: IDTYPE=BYID, CELLID=Cell index value, ITEMINDEX=91,
ITEMVALUE=239;
Bit 4 and bit 3 of software parameter 91 are used to configure the coefficient of the IF filter.
The following table lists the meanings of bit 4 and bit 3.
BIT4-BIT3
Filter
00
260K
01
200K
10
Reserved
11
200K
bandwidth
Note:
1. When the IF filter coefficients of D series and M series are configured, use different bits of the
same software parameter.
The default values (10 and 11) in the IF filter coefficient configuration of D series and M series
are different. The default value of D series is 200K bandwidth, and the default value of M series is
260K bandwidth. The reserved value 10 cannot be configured.
2015-8-4
Huawei Confidential
Page 68 of 68