Beruflich Dokumente
Kultur Dokumente
Packet Tracer
T
- Configu
uring a Linksys
L
Router
T
Topology
O
Objectives
Part 1: Co
onnect to Lin
nksys routerr
Part 2: En
nable Wireless Connectiv
vity
Part 3: Co
onfigure and
d Verify Wireless Client Access
A
B
Backgroun
nd
In this acttivity, you will configure a Linksys
L
wirele
ess router, allo
owing remote
e access to w
wireless clientss as well
as connec
ctivity with WP
PA security.
P
Part 1: Connect
C
to
t Linksy
ys Routerr
S
Step 1: Establish and verify conn
nectivity to the Linksys
s router.
a. Connect the appro
opriate cable from
f
Host-A to
t the Etherne
et 1 port on L
Linksys.
f the link light to turn gree
en. Then ope
en the comma
and prompt fo
or Host-A. Usse the ipconfiig
b. Wait for
comm
mand to verify Host-received IP addressing informattion.
c.
S
Step 2: Ac
ccess the Linksys grap
phical user interface
i
(G
GUI) using a web brows
ser.
a. To co
onfigure the Linksys routerr using the GU
UI, you will ne
eed to accesss it using the Host-A web browser.
Open the web brow
wser and acce
ess Linksys by entering th
he default gatteway addresss in the URL field.
b. Enter admin as the
e default userrname and pa
assword to acccess the Lin
nksys router.
Note:: You will not see your score change wh
hen configurin
ng the Linksy
ys router untill you click Sa
ave
Settin
ngs.
Page 1 of 4
DNS 1 - 198.133.219.10
IP Address - 172.31.1.1
Note: The IP address range of the DHCP pool will only reflect the changes once you click 'Save Settings'
Return to the command prompt of Host-A. Enter the command ipconfig /renew to renew the IP address.
d. Use the Host-A web browser to reconnect to the Linksys. You will need to use the new default gateway
address. Verify the Internet Connection settings in the Status tab. The settings should match the values
you configured in Part 2, Step 1. If not, repeat Part 2, Step 1 and Step 2.
2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.
Page 2 of 4
e. For best performance in a network using Wireless-N, set the radio band to Wide-40MHz.
f.
Step 5: Configure wireless sercurity so that clients must authenticate to connect to the
wireless network.
a. Click the Wireless Security option under the Wireless tab.
b. Set the Security Mode to WPA2 Personal.
What is the difference between personal and enterprise?
c.
Leave the encryption mode to AES and set the passphrase to itsasecret.
Step 6: Change the default password to access the Linksys for configuration.
a. You should always change the default password. Click the Administration tab and change the Router
Access password to letmein.
b. Click Save Settings. Enter the username admin and the new password.
Close the Linksys GUI and click Command Prompt. Enter the command ipconfig to verify Laptop
received IP addressing.
2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.
Page 3 of 4
Question
Location
Possible
Points
Step 4
Step 5
Part 2 Total
95
Total Score
100
2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.
Earned
Points
Page 4 of 4