Beruflich Dokumente
Kultur Dokumente
Revised 07-04-14
Index
Product Training
Hydraulics Courses
Introduction to Maintenance Hydraulics Technology ....................................................... 6
Introduction to Hydraulic Proportional Systems............................................................... 8
Introduction to Basic Hydraulic Design ............................................................................ 10
Introduction to Hydraulic Pump Control ......................................................................... 12
Bespoke Hydraulics Workshop .......................................................................................... 13
Introduction to Industrial Filtration Products ................................................................. 14
Advanced Introduction to Industrial Filtration Products............................................... 15
Advanced Contamination Control with Industrial Filtration Products ........................ 16
Advanced Contamination Control with Filtration Products on Mobile Applications . 17
Introduction to installation & Maintenance of Large Hydraulic Drives ....................... 18
Introduction to installation & Maintenance of Large Hydraulic Drives ....................... 19
Motion Control Courses
Introduction to IndraDrives with IndraWorks ................................................................ 20
Introduction to IndraDrive-Mi with IndraWorks ........................................................... 21
Advanced IndraDrives with IndraWorks ......................................................................... 22
Advanced IndraDrive-Mi with IndraWorks .................................................................... 23
Introduction to IndraMotion for Handling with IndraDrives ........................................ 24
Introduction to SMC Axis Control with IndraDrives ..................................................... 25
Introduction to Drive based Safety with IndraDrives ..................................................... 26
Introduction to SLc Safety Relay ....................................................................................... 27
Introduction to MLD-S Axis Control with IndraWorks & IndraDrives....................... 28
Introduction to MLD-M Axis Control with IndraWorks & IndraDrives ..................... 29
Advanced MLD-S Axis Control with IndraWorks & IndraDrives................................ 30
Advanced MLD-M Axis Control with IndraWorks & IndraDrives .............................. 31
Introduction to MLC Axis Control with IndraWorks & IndraDrives .......................... 32
Advanced MLC Axis Control with IndraWorks & IndraDrives ................................... 33
Advanced MLC Axis Control with IndraWorks & IndraDrives (Inc. Cams) .............. 34
Introduction to XLC Axis Control with IndraWorks & IndraDrives ........................... 35
Advanced XLC Axis Control with IndraWorks & IndraDrives .................................... 36
Introduction to MLC Axis Control with IndraWorks & IndraDrives .......................... 37
Advanced MLC Axis Control with IndraWorks & IndraDrives ................................... 38
Advanced MLC Axis Control with IndraWorks & IndraDrives (Inc. Cams) .............. 39
Introduction to MTX Axis Control Operator Interface .................................................. 40
Introduction to MTX Axis Control & IndraDrives ......................................................... 41
Advanced MTX Axis Control & IndraDrives .................................................................. 42
Training courses not found in this 2014 brochure will be found on our website
http://www.boschrexroth.co.uk/training
Courses not found here may be available on special request by Email
academy@boschrexroth.co.uk
Trainers
All of our trainers are qualified engineers and have wealth of industrial experience, including within our own
Service and/or Applications functions.
Courses
We offer an extensive training programme across our full range of drive and control systems, including Bosch AT
& Indramat. All courses can be structured to your production processes, giving you just the training you need.
Locations
We are able to deliver courses at one of our Rexroth Technical and Service Centres or on your premises.
Our training centres are located at:
St. Neots, Cambridgeshire
Cirencester, Gloucestershire
Wakefield, West Yorkshire
Cork, Southern Ireland
Training Systems
Training systems and play mobiles are available using current industrial standard components in Hydraulics,
Pneumatics, Mechatronics and Motion-Control technologies and are delivered fully assembled and ready to use.
From one rig to a full lab solution Rexroth is the only company able to supply industrial standard components
across all the technologies. Rexroth can also provide all the training documentation for both the Teacher and the
students.
eLearning
We currently have a diverse range of eLearning products which can be accessed via our LearnWorld portal.
Create a guest account in our LearnWorld and experience our free content.
Media
As part of our LearnWorld we are able to offer education providers a wide range of media solutions; posters,
animations, software and access to our technical product library.
Contact Us
Should you require further information or to discuss your training needs please contact us via email at
academy@boschrexroth.co.uk or telephone 01480-223282 for hydraulics or 01285-863023 for electric drives &
controls.
David Stirling
Technical Training Manager
Bosch Rexroth
The Drive & Control Company.
Target Groups
Hydraulic Maintenance Engineers
Commissioning Engineers
Project Engineers
Sales & Technical personnel
Prerequisite
Participants should have a mechanical engineering background but this is not essential
Learning targets
To impart a basic understanding of maintenance hydraulics
To increase the knowledge of personnel who are actively involved in the repair and maintenance of hydraulic
systems
To allow participants to become familiar with fluid power technologies such as pump flow, cylinder speed,
forces and pipe sizes
Introduce basic hydraulic theory in a practical way
To increase the knowledge of personnel in fault finding techniques associated with hydraulic systems
To enable participants to understand their specific hydraulic installations and their specific circuit diagrams
To gain hands-on experience of building, fault finding and optimising hydraulic circuits using the Rexroth
range of training rigs
Content
Basic hydraulic principles, Hydraulic symbols and circuit notations
Pressure control (Relief & Reducing) and associated circuitry
Sequence valves, Counter balance and overcentre valves
Flow control & Throttle valves inc pressure & temperature compensated units
Directional Control valves, direct operated and two stage pilot operated
Poppet valves and logic cartridge elements
Duration
3 days. Courses generally run Tues-Thurs (unless otherwise indicated on schedule of dates),
9am - 5pm each day.
Course equipment
All course materials including Hydraulic Trainer Vol 1.
Full demonstration DS4/WS290 hydraulic training rigs (excludes customer site*)
Training locations
Bosch Rexroth facilities St. Neots or Wakefield (courses at St. Neots to include a factory tour)
Bosch Rexroth official distributor facilities in Eire
Customer site (excludes DS4/WS290 training rigs*)
Pricing
At a Bosch Rexroth facility
On site ROI
Customer site
Target Groups
Hydraulic Maintenance Engineers
Commissioning Engineers
Project Engineers
Sales & Technical personnel
Prerequisite
Participants would benefit from having a mechanical engineering background and having attended our
course HYD-MAINTHYD1-TECH or to have an understanding of its learning targets.
Learning targets
To introduce attendees to the principles and practices of proportional control
Introduction to the study of circuit construction and circuit components
To introduce the basic principles of the design of proportional systems
To gain a knowledge of both analogue and digital proportional systems
To become familiar with the set-up procedures on proportional systems
Familiarity with fault finding techniques on proportional systems
Content
Valve construction and operation
Types of proportional control
Pressure relief, Flow control & directional control valves
Hydraulic symbols
Spool configurations
Selection & sizing with reference to manufacturers data
Electrical operation
Types of proportional control devices
Basic electrical circuits and operations
Solenoid design
Comparison between conventional and proportional valves
Methods of control
Comparison between analogue and digital control
Proportional attributes
Ramp, Gain, Deadband, Dither and Pulse width modification
Amplifier Cards
Principles of operation
Design and application
Analogue & digital
Closed loop
Internal & external feedback devices
Operation and application of closed loop systems
Duration
3 days, courses generally run Tues-Thurs (unless otherwise indicated on schedule of dates),
9am - 5pm each day.
Course equipment
All course materials including Hydraulic Trainer Vol 2.
Full demonstration DS4 hydraulic training rigs (excludes customer site*)
Training locations
Bosch Rexroth facilities St. Neots or Wakefield (courses at St Neots include a factory tour).
Bosch Rexroth official distributor facilities in Eire.
Customer site (excludes DS4 training rigs).
Pricing
At a Bosch Rexroth facility
On site ROI
Customer site
Scheduled dates
Please contact us for available dates
Target Groups
Hydraulic Maintenance Engineers
Project Engineers
Sales & Technical personnel
Prerequisite
Participants would benefit from having a mechanical engineering background and having attended our
course HYD-MAINTHYD1-TECH or to have an understanding of its learning targets. This course takes a
more mathematical approach to the theory covered in the MAINTHYD1 course.
Learning targets
To understand the basic theory and operation of hydraulic components
To understand basic circuit design and project work
An overview of machine design incorporating hydraulic components/systems
Content
Fundamental principles
Cylinders relationship between valves
Cylinder size, pressure, area and effective force
Cylinder size, supply flow rate and velocity
Motors
Motor displacement, pressure and shaft torque
Motor displacement, supply flow rate and shaft speed
Motor performance and effects of fluid viscosity
Loads to be moved
Application of the laws of dynamics, with reference to mass & inertia, friction, gravity and other external
forces; direct and indirect loads
Pumps
Displacement, shaft speed and flow rate
Flow rate, system pressure and fluid viscosity
Pressure difference, component flow area and flow rate
Fluid viscosity, Renolds number, flow characteristics, recommended flow velocities
Pressure difference, flow rates, heat generation and temperature changes
Duration
3 days (courses run Tues-Thurs) 9am 5pm each day
10
Course equipment
All course materials, including Hydraulic Trainer Vol 3.
No practical work is included in this training.
Training locations
Bosch Rexroth facilities St. Neots or Wakefield (courses at St Neots include a factory tour).
Bosch Rexroth official distributor facilities in Eire.
Customer site
Pricing
At a Bosch Rexroth facility
On site ROI
Customer site
Scheduled dates
Please contact us for available dates
11
Target Groups
Hydraulic Maintenance Engineers
Project Engineers
Sales & Technical personnel
Prerequisites
Participants would benefit from having a mechanical engineering background and having attended our
course HYD-MAINTHYD1-TECH or to have an understanding of its learning targets.
Learning targets
To understand the function and operation of pumps and their controls
To be able to make the correct pump selection based on application
To understand the cause of pump failure
To understand the affects of contamination
To understand the set up procedures of pump and pump control
To understand safe working practice
Content
Pump Types, Function & Operation
Pump selection
Pump controls
Fixed displacement
Variable displacement
Relief valves, flow control valves, Unloading valves
Accumulators and pressure switches
Pressure compensation
Load sensing and constant power
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training locations
- Worksop, Nottingham.
- Customer site subject to suitable working environment being available
Pricing
Worksop
Customer site
12
Scheduled dates
Please contact us for available dates
Target Groups
Hydraulic Maintenance Engineers
Commissioning Engineers
Prerequisite
Participants would benefit from having a mechanical engineering background and having attended our
course HYD-MAINTHYD1-TECH or to have an understanding of its learning targets.
Learning targets
To be agreed with the Rexroth training department prior to development of the required course.
Usually based on existing machinery and circuitry / parts lists supplied by the customer.
Content
Bespoke to each course
Duration
To suit customer requirements
Course equipment
Familiarisation training on specific customer equipment (subject to safety an access restraints) if required.
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Pricing
Please contact us for details
Scheduled dates
Please contact us for available dates
13
Target Groups
Maintenance Personnel
Process Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with automation
and factory floor working environments
Learning targets
Rexroth range of hydraulic filtration systems
Basic knowledge for oil cleanliness
Particulates and component damage
Content
High pressure products
Low pressure products
Duration
One day
Course equipment
Static examples available to aid explanation
Training location
Your site with a suitable environment or a Bosch Rexroth facility
14
Delivery times
Training will commence at 9.00am each day
Target Groups
Distribution Sales Staff
Process Engineers
OEM Design Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with automation
and factory floor working environments.
Learning targets
Rexroth range of hydraulic filtration systems
Basic knowledge for oil cleanliness
Particulates and component damage
Content
High pressure products
Low pressure products
Filtration benefits
Duration
One day
Course equipment
Static examples available to aid explanation
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
15
Target Groups
Hydraulic Maintenance Engineers
Distribution Sales Staff
Process Engineers
OEM Design Engineers
OEM Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have a mechanical engineering background and be familiar with automation and factory
floor working environments
Learning targets
Rexroth range of hydraulic filtration systems
Knowledge for oil cleanliness and the long term benefits
Machine life cycle and extending useful production life
Particulates and component damage
Content
High pressure products
Low pressure products
Filtration benefits
Filtration technology
Duration
One day
Course equipment
Static examples available to aid explanation
Training location
Your site with a suitable environment or a Bosch Rexroth facility
16
Delivery times
Training will commence at 9.00am each day
Target Groups
Hydraulic Maintenance Engineers
Distribution Sales Staff
Process Engineers
OEM Design Engineers
OEM Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have a mechanical engineering background and be familiar with automation and factory
floor working environments
Learning targets
Rexroth range of hydraulic filtration systems
Knowledge for oil cleanliness and the long term benefits
Machine life cycle and extending useful production life
Particulates and component damage
Content
High pressure products
Low pressure products
Filtration benefits
Filtration technology
Duration
One day
Course equipment
Static examples available to aid explanation
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
17
Target Groups
Hydraulic Maintenance Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have a mechanical engineering background and be familiar with the Windows operating
system
Learning targets
To have knowledge of LHD (Hgglunds) motor functionality, installation, commissioning and maintenance.
Relevant interface configuration
Content
Operating / design principles
Drive / Machine interface
System recommendations & cautions
Installation procedure, piping connections,
Storage requirements, fluids.
Commissioning and Maintenance
Faultfinding & diagnostics
Duration
One day
Course equipment
Power point presentation with a workshop visit to view our products (Available at the Normanton facility)
Training location
Your site with a suitable environment or a Bosch Rexroth facility
18
Delivery times
Training will commence at 9.00am each day
Target Groups
Hydraulic Maintenance Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have a mechanical engineering background and be familiar with the Windows operating
system
Learning targets
To have knowledge of LHD (Hgglunds) motor functionality, operation and maintenance of the drive system
Content
Operating / design principles
Drive / Machine interface
System recommendations & cautions
Installation procedure, piping connections,
Storage requirements, fluids.
Commissioning and Maintenance
Faultfinding & diagnostics
Duration
One day
Course equipment
Power point presentation and hands on site instruction/explanation
Training location
Your site and tailored to your drive system
Delivery times
Training will commence at 9.00am each day
19
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of Servo drive theory and functionality
Relevant interface configuration
Content
Servo drive theory
Electrical connections
Faultfinding & diagnostics
Archive & restore of parameters
Drive based safety technology
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
20
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of Servo drive theory and functionality
Relevant interface configuration
Content
Servo drive theory
Electrical connections
Interface
Faultfinding & diagnostics
Archive & restore parameters
Drive based safety technology
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
21
Target Groups
Maintenance/first response Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of Servo drive theory and functionality
Relevant interface configuration
Successful maintenance interventions
Content
Servo drive theory
Electrical connections
Interface
Faultfinding & diagnostics
Drive parameters configuration using IndraWorks
Archive & restore parameters
Drive based safety technology
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
22
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of Servo drive theory and functionality
Relevant interface configuration
Successful maintenance interventions
Content
Servo drive theory
Electrical connections
Interface
Diagnostics
Drive parameters configuration using IndraWorks
Archive & restore parameters
Drive based safety technology
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
23
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Servo drive theory and faultfinding
To have knowledge of the configuration of the control
Successful maintenance interventions
Programming through the hand control
Content
Servo drive theory
Electrical connections
Parameters
Programming overview
Diagnostics
Duration
One day
Course equipment
Full working demonstration play-mobiles, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
24
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Servo drive theory and faultfinding
To have knowledge of the configuration of the control
Successful maintenance interventions
Programming
Content
Servo drive theory
Electrical connections
Parameters
Programming overview
Diagnostics
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
25
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of the relevant EN or ISO standard
Hardware configuration
Successful maintenance interventions
Content
Overview of risk assessment
Safety On-board
Electrical connections
Parameters
Programming overview
Diagnostics
Drive exchange and required documentation
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
26
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of the relevant EN or ISO standard
Hardware configuration
Content
Overview of risk assessment
Safety On-board
Electrical connections
Parameters
Programming overview
Diagnostics
Exchange and required documentation
Duration
One day
Course equipment
Full working demonstration play-mobile
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
27
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Use of the IndraWorks software
Use of the IndraLogic software for PLC
Successful maintenance interventions
Content
IndraDrives
IndraWorks parameter configuration
IndraLogic program introduction
Drive command functions
Archiving and restoring backup files
Drive based safety technology
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
28
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Use of the IndraWorks software
Use of the IndraLogic software for PLC
Successful maintenance interventions
Content
IndraDrives, including Sercos3
IndraWorks parameter configuration
IndraLogic program introduction
Drive command functions
CCD cross drive communication
Archiving and restoring backup files
Drive based safety technology
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
29
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Successful maintenance interventions
Use of the IndraWorks software
Use of the IndraLogic software for PLC
Writing program examples
Content
Drive configuration
Faultfinding & diagnosis
IndraWorks parameter configuration
IndraLogic program construction
Drive command functions
Archiving and restoring backup files
Drive based safety technology
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
30
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Successful maintenance interventions
Use of the IndraWorks software
Use of the IndraLogic software for PLC
Writing program examples
Content
Drive configuration, including Sercos3
Faultfinding & diagnosis
IndraWorks parameter configuration
IndraLogic program construction
Drive command functions
CCD cross drive communication
Archiving and restoring backup files
Drive based safety technology
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
31
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Use of the IndraWorks software
Overview of IndraLogic software for PLC
Successful maintenance interventions
Content
Drive configuration, including Sercos
Faultfinding & diagnosis
IndraWorks parameter configuration
Drive command functions
Archiving and restoring backup files
Drive based safety technology
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
32
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Use of the IndraWorks software
Use of the IndraLogic software for PLC (1G)
Writing program examples
Content
Drive configuration, including Sercos
Faultfinding & diagnosis
IndraWorks parameter configuration
Successful maintenance interventions
IndraLogic program construction (1G)
Drive command functions
Archiving and restoring backup file
Drive based safety technology
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
33
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Successful maintenance interventions
Use of the IndraWorks software
Use of the IndraLogic software for PLC (1G)
Writing program examples
Content
Drive configuration, including Sercos
Faultfinding & diagnosis
IndraWorks parameter configuration
IndraLogic program construction (1G)
Drive command functions
Cam functions
Archiving and restoring backup files
Drive based safety technology
Duration
Four days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
34
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Use of the IndraWorks software
Overview of IndraLogic software for PLC
Successful maintenance interventions
Content
Drive configuration, including Sercos
Faultfinding & diagnosis
IndraWorks parameter configuration
Drive command functions
Archiving and restoring backup files
Drive based safety technology
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
On site at customers
3,525.00
At a Bosch Rexroth facility
2,625.00
Shopfloor panel guide with a service engineer
1,050.00 (One day without documentation)
On site ROI
4,718.00
Prices are inclusive of the Trainers travel and subsistence
A surcharge will be made for any additional participants
Delivery times
Training will commence at 9.00am each day
35
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Successful maintenance interventions
Use of the IndraWorks software
Use of the IndraLogic software for PLC (2G)
Writing program examples
Content
Drive configuration, including Sercos
Faultfinding & diagnosis
IndraWorks parameter configuration
IndraLogic program construction (2G)
Drive command functions
Archiving and restoring backup files
Drive based safety technology
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
On site at customers
4,891.00
At a Bosch Rexroth facility
3,991.00
On site ROI
6,427.00
Prices are inclusive of the Trainers travel and subsistence
A surcharge will be made for any additional participants
Delivery times
Training will commence at 9.00am each day
36
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Use of the IndraWorks software
Overview of IndraLogic software for PLC
Successful maintenance interventions
Content
Drive configuration, including Sercos
Faultfinding & diagnosis
IndraWorks parameter configuration
Drive command functions
Archiving and restoring backup files
Drive based safety technology
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
37
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Successful maintenance interventions
Use of the IndraWorks software
Use of the IndraLogic software for PLC (2G)
Writing program examples
Content
Drive configuration, including Sercos
Faultfinding & diagnosis
IndraWorks parameter configuration
IndraLogic program construction (2G)
Drive command functions
Archiving and restoring backup files
Drive based safety technology
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
38
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Successful maintenance interventions
Use of the IndraWorks software
Use of the IndraLogic software for PLC (2G)
Writing program examples
Content
Drive configuration, including Sercos
Faultfinding & diagnosis
IndraWorks parameter configuration
IndraLogic program construction (2G)
Drive command functions
Cam functions
Archiving and restoring backup file
Drive based safety technology
Duration
Four days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
39
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Understanding of different hardware components
Overview of PLC programming
Overview of NC programming
Archiving of system files and restoring backup data.
Content
Hardware configuration
System files and the configurations of the MTX control
Navigation of the MTX Operation interface
NC programming
Viewing Tool management data
Archiving of system files and restoring backup data.
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
40
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital servo drive
Successful maintenance interventions
Overview of PLC programming
Overview of NC programming
Archiving of system files and restoring backup data.
Content
Digital servo drive theory
Faultfinding & diagnosis
Drive & control parameters
Sercos interface
Introduction to IndraLogic PLC
NC programming
Archiving of system files and restoring backup data
Drive based safety technology
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
41
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital servo drive
Successful maintenance interventions
To understand the system files and the configurations of the MTX system
Overview of PLC programming
Overview of NC programming
Archiving of system files and restoring backup data.
Content
Digital servo drive theory
To understand the system files and the configurations of the MTX system
Drive & control parameters
Sercos interface
IndraLogic PLC programming
NC programming
PCL programming introduction
Archiving of system files and restoring backup data
Drive based safety technology
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
42
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the system files and the configurations of the system
Navigation of the IndraLogic PLC software
Successful maintenance interventions
Archiving of system files and restoring backup data
Content
To understand the system files and the configurations of the system
Hardware configuration
Introduction to IndraLogic PLC programming with simple examples in LD & ST
Function blocks
Variables, timers & counters
Archiving of system files and restoring backup data
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
43
Target Groups
Maintenance Personnel
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the system files and the configurations of the system
Navigation of the PLC software
Successful maintenance interventions
Archiving of system files and restoring backup data.
Content
To understand the system files and the configurations of the system
Hardware configuration
Introduction to IndraLogic PLC programming with simple examples in LD & ST
Function blocks
Variables, timers & counters
Archiving of system files and restoring backup data.
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
44
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the system files and the configurations of the system
PLC programming
Successful maintenance interventions
Archiving of system files and restoring backup data.
Content
To understand the system files and the configurations of the system
Hardware configuration
Introduction to IndraLogic PLC programming with simple examples in IL, LD & ST
Function blocks
Variables, timers & counters
Archiving of system files and restoring backup data.
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
45
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the system files and the configurations of the system
PLC programming
Successful maintenance interventions
Archiving of system files and restoring backup data.
Content
To understand the system files and the configurations of the system
Hardware configuration
Introduction to IndraLogic PLC programming with simple examples in IL, LD & ST
Function blocks
Variables, timers & counters
Archiving of system files and restoring backup data.
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
46
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the technology functions
Relevant interface configuration
Content
Product overview
Connections
Diagnostics
Syllabus driven by the customer
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
47
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the timer functions
Relevant interface configuration
Successful maintenance interventions
Content
Welding theory
Connections
Interface
Diagnostics
Timer configuration
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
48
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system. They should already have a good understanding of Rexroth MFDC weld
controllers and have completed the BOS6000 maintenance course.
Learning targets
To understand the system hardware
Principle of operation
Successful maintenance interventions
Content
Welding theory using UIR optional hardware
Connections
Interface
Diagnostics
Timer configuration
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
49
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the timer functions
Relevant interface configuration
Principle of operation of PSQ quality system
Successful maintenance interventions
Content
Welding theory
Connections
Interface
Diagnostics
Timer configuration
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
50
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the timer functions
Relevant interface configuration
Successful maintenance interventions
Content
Welding theory
Connections
Interface
Diagnostics
Timer configuration
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
51
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the timer functions
Relevant interface configuration
Successful maintenance interventions
Principle of operation of PSQ quality system
Content
Welding theory
Connections
Interface
Diagnostics
Timer configuration
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
52
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To understand the timer functions
Relevant interface configuration
Successful maintenance interventions
Content
Welding overview
Connections
Diagnostics
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
53
Target Groups
Machine Operators
Maintenance Personnel
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Bolting theory
System configuration
Correct operation of Rexroth equipment
Successful maintenance interventions
Content
Basics of tightening
Bolting components
System Overview
Operation of the program and faultfinding
Diagnostics & error correction
Documentation
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
54
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Bolting theory
System configuration
Maintenance and diagnostic techniques
Successful maintenance interventions
Content
Basics of tightening
Bolting components
System configuration
Exchange of system components
System data upload reload
Operation of the programming and faultfinding software tools
Strategies for SE300 systems
Diagnostics
Documentation
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
55
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Pressing theory
System configuration
Maintenance and diagnostic techniques
Successful maintenance interventions
Content
Basics of press fitting
Press-fit components
Interfacing
System configuration
Exchange of system components
System data upload reload
Operation of the PEPR software tools
Diagnostics
Documentation
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
56
Delivery times
Training will commence at 9.00am each day
Target Groups
Machine Operators
Maintenance Personnel
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Bolting theory
System configuration
Correct operation of Rexroth equipment
Successful maintenance interventions
Content
Basics of tightening
Bolting components
System Overview
Operation of the program and faultfinding
Diagnostics & error correction
Documentation
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
57
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Bolting theory
System configuration
Maintenance and diagnostic techniques
Successful maintenance interventions
Content
Basics of tightening
Bolting components
System configuration
Exchange of system components
System data upload reload
Operation of the programming and faultfinding software tools
Strategies for System 350
Diagnostics
Documentation
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
58
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Bolting theory
System configuration
Maintenance and diagnostic techniques
Successful maintenance interventions
Overview of IndraLogic PLC
Content
Basics of tightening
Bolting components
System configuration
Exchange of system components
System data upload reload
Operation of the programming and faultfinding software tools
Navigation of IndraLogic program
Strategies for System 350
Diagnostics
Documentation
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
59
Target Groups
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system and a working knowledge of PLC and IndraLogic or to have completed the
IndraLogic training course.
Learning targets
Overview of VCP hardware
System configuration
Maintenance and diagnostic techniques
Successful maintenance interventions
Content
Installation of software
Creating a basic project
Basic setup
Interface to the PLC
Symbol table and variables
Inage administration, image creation, image control
Generating objects
Assigning object properties
Variable administration, variable display
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
60
Delivery times
Training will commence at 9.00am each day
Target Groups
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system and a working knowledge of PLC and IndraLogic or to have completed the
IndraLogic training course.
Learning targets
Overview of hardware
System configuration
Maintenance and diagnostic techniques
Content
Installation of software
Creating a basic project
Basic setup
Interface to the PLC
Symbol table and variables
Inage administration, image creation, image control
Generating objects
Assigning object properties
Variable administration, variable display
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
61
Target Groups
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system and a working knowledge of PLC and IndraLogic or to have completed the
IndraLogic training course.
Learning targets
Overview of hardware
System configuration
Maintenance and diagnostic techniques
Content
Installation of software
Creating a basic project
Basic setup
Interface to the PLC
Symbol table and variables
Inage administration, image creation, image control
Generating objects
Assigning object properties
Variable administration, variable display
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
62
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background.
Learning targets
To have knowledge of Servo drive theory and functionality
Successful maintenance interventions
Content
Servo drive theory
Electrical connections
Interface
Faultfinding & diagnostics
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
63
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of Servo drive theory and functionality
Relevant interface configuration
Successful maintenance interventions
Content
Servo drive theory
Electrical connections
Interface
Faultfinding & diagnostics
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
64
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of Servo drive theory and functionality
Relevant interface configuration
Successful maintenance interventions
Content
Servo drive theory
Connections
Interface
Faultfinding & diagnostics
Use of the DriveTop software
Drive configuration
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
65
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of Servo drive theory and functionality
Relevant interface configuration
Successful maintenance interventions
Content
Servo drive theory
Connections
Interface
Faultfinding & diagnostics
Archive & restore of parameters
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
66
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
To have knowledge of Servo drive theory and functionality
Relevant interface configuration
Successful maintenance interventions
Content
Servo drive theory
Connections
Interface
Faultfinding & diagnostics
Use of DriveTop software
Drive configuration
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
67
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Relevant drive course undertaken
Learning targets
To have knowledge of the configuration of the control
Use of the Motion Manager software
Programming
Successful maintenance interventions
Content
Electrical connections
Parameters
Programming overview
Control diagnostics
Duration
One day
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
68
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Servo drive theory and faultfinding
To have knowledge of the configuration of the control
Use of the Motion Manager software
Programming
Successful maintenance interventions
Content
Servo drive faultfinding & diagnosis
Electrical connections
Parameters
Programming overview
Faultfinding & diagnostics
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
69
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Servo drive theory and faultfinding
To have knowledge of the configuration of the control
Use of the Motion Manager software
Programming
Successful maintenance interventions
Content
Servo drive faultfinding & diagnosis
Electrical connections
Parameters
Programming overview
Faultfinding & diagnostics
DriveTop software
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
70
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To understand the system files
Use of the VisualMotion software
Understanding of ELS theory
Successful maintenance interventions
Content
I/O files
Registers
Basic drive configuration
Diagnostic functions
Archiving and restoring backup files
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
71
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To understand the system files
Use of the VisualMotion software
Understanding of ELS theory
Successful maintenance interventions
Content
I/O files
Registers
Basic drive configuration
Diagnostic functions
Archiving and restoring backup files
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
72
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To understand the system files
Use of the SYNTOP software
Understanding of ELS theory
Successful maintenance interventions
Content
ELS theory
Sercos interface
Overview of Virtual/Real master control
Overview of Velocity Synchronisation
Overview of Phase Synchronisation
Diagnostic functions
Archiving and restoring backup files
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
73
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Programming of the VisualMotion software
Writing program examples
Understanding of ELS theory
Successful maintenance interventions
Content
I/O files
Registers
Drive parameterisation
Program construction
Auxiliary functions
Diagnostic functions
Archiving and restoring backup files
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
74
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Programming of the VisualMotion software
Writing program examples
Understanding of ELS theory
Successful maintenance interventions
Content
I/O files
Registers
Drive parameterisation
Program construction
Auxiliary functions
Diagnostic functions
Archiving and restoring backup files
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
75
Target Groups
Maintenance Personnel
Control Engineers
Commissioning Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Programming of the SYNTOP software
Understanding of ELS theory
Successful maintenance interventions
Content
ELS theory
Sercos configuration
Virtual/Real master control
Velocity Synchronisation
Phase Synchronisation
Process control
Diagnostic functions
Archiving and restoring backup files
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
76
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Use of the VisualMotion software
Understanding of ELS theory
Successful maintenance interventions
Content
I/O files
Registers
Basic drive configuration
Diagnostic functions
Archiving and restoring backup files
Duration
Two days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
77
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
IndraDrive servo theory.
To have knowledge of the system files and configuration
Use of the VisualMotion software
Use of the IndraLogic software for PLC
Writing program examples
Understanding of ELS theory
Successful maintenance interventions
Content
I/O files
IndraLogic
Registers
Drive parameterisation
Diagnostic functions
Program construction
Auxiliary functions
Archiving and restoring backup files
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
78
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
IndraDrive servo theory.
To have knowledge of the system files and configuration
Use of the SYNTOP software
Overview of IndraLogic software for PLC
Understanding of ELS theory
Successful maintenance interventions
Content
ELS theory
Sercos interface
Diagnostic functions
Overview of Virtual/Real master control
Overview of Velocity Synchronisation
Overview of Phase Synchronisation
Auxiliary functions
Overview of IndraLogic
Duration
Three days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
79
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
IndraDrive servo theory.
To have knowledge of the system files and configuration
Use of the VisualMotion software
Use of the IndraLogic software for PLC
Writing program examples
Understanding of ELS theory
Successful maintenance interventions
Content
I/O files
IndraLogic
Registers
Drive configuration
Diagnostic functions
Program construction
Auxiliary functions
Archiving and restoring backup files
Duration
Four days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
80
Delivery times
Training will commence at 9.00am each day
Target Groups
Maintenance Personnel
Control Engineers
Maximum number of attendees for this course is four
Prerequisite
Participants should have an electrical or mechanical engineering background and be familiar with the
Windows operating system
Learning targets
Digital Servo drive theory
To have knowledge of the system files and configuration
Use of the SYNTOP software
Overview of IndraLogic software for PLC
Understanding of ELS theory
Successful maintenance interventions
Content
ELS theory
Sercos interface
Diagnostic functions
Overview of Virtual/Real master control
Overview of Velocity Synchronisation
Overview of Phase Synchronisation
Auxiliary functions
Overview of IndraLogic
Duration
Four days
Course equipment
Full working demonstration play-mobiles at a rate of 2 people per station, where possible
Training location
Your site with a suitable environment or a Bosch Rexroth facility
Delivery times
Training will commence at 9.00am each day
81
In addition:
Included
Trainers transportation on mainland UK
Subsistence costs including hotels
Course documentation on full training courses
Fact sheets are provided with the Service Engineer panel overviews
Excluded
Prices are excluding VAT which will be charged at the current rate
There are no training presentations/manuals with the Service Engineer panel overviews
Customer travel and subsistence cost if training is delivered at a Bosch Rexroth site
Equipment transport costs via courier where incurred and will be charged at cost
Courses conducted outside normal working hours will be surcharged at an additional 50%
Air flights, ferrys and car hire are charged at cost at the time of the course where incurred
Booking courses.
We reserve the right to amend any prices or conditions quoted in this catalogue without
prior notice.
Contact
Technical Training
Tel:
Fax:
Email:
82
Email:
Tel:
dave.stirling@boschrexroth.co.uk
+44 (0)1285 863023
Hydraulics:
Standard courses / Large Hydraulic Drives / Filtration /
Special and Bespoke Hydraulic Training requests:
Contact: Marie Morris
Training Co-Ordinator
E-Mail:
Tel:
marie.morris@boschrexroth.co.uk
+44 (0) 1480 223282
E-Mail:
academy@boschrexroth.co.uk
83
My Notes:
84
85
86