Beruflich Dokumente
Kultur Dokumente
Dodge Cummins
EFILive
Instructions
-----------------------------------------------------------------Package Contents
AutoCal W/ 1 Pre-loaded Tune
AutoCal Cables USB & OBDII
Koozi
PPEI Flash Drive Pre-loaded W/ Tunes and Instructions
PPEI Sticker
(If you are missing any of the above Items please contact us before proceeding)
Install Instructions
1. Plug the AutoCal into the trucks OBDII using supplied cables.
2. Turn the key to the RUN position, do not start the truck.
3. Toggle down using the right (skull) button until you see Tuning Tool.
Press the OK button (skull) in the center of the AutoCal..
4. Toggle down to Program Full press OK.
5. Toggle down to Unlock press OK the screen will say Checking to
100%.
6. It will ask if you want to LICENSES ECU NOW press OK.
7. It will now ask Are you sure press OK.
8. The AutoCal should now say Please Wait. Erasing Flashing with a
percentage (%) below it. The flashing process takes approximately 10
minutes.
9. When the flashing has finished, the AutoCal will prompt you to turn the
ignition off now! Turn the key off and press OK. A countdown will appear.
Once the countdown has finished you have now unlocked your PCM. DO
NOT START YOUR TRUCK.
10. The AutoCal will be on the Program Full screen. Press OK.
11. Turn the key to the RUN position, do not start the truck.
12. Toggle down to the pre-loaded tune (Default tune is ECOTOW) press
OK.
13. The screen will say Checking 0 - 100% Followed by Erasing
Flashing with a percentage % below it. This process take approximately 13
minutes.
14. When the flashing has finished, the AutoCal will prompt you to turn the
ignition off now! Turn the key off and press OK. Once the countdown has
completed you have now successfully loaded your new tune onto your truck,
you may turn the key to the run position and start the truck!
1. Plug both PPEI USB Flash drive and AutoCal into your computer.
2. The flash drive will automatically open up on your desktop with all your tunes
including EFILive V8 software.
Double click on EFILive V8 Setup (at the bottom).
3. A Pop-up for User Account Control will then come up asking "Do you want to
allow EFILive V8 Scan and Tune to make changes to this computer".
Click Yes.
4. EFIlive Scan and Tune Setup will then open up to their Installer.
Click Next.
5. EFILive Licenses Agreement will prompt you to read the following document
carefully.
Select check box "I agree to the terms of this licenses agreement".
Click Next to proceed to the next step of the installation of EFILive Scan
and Tune.
6. EFILive Installation Folder will be the next step in the install.
Click Next for allowing the Software to be installed to "c:\Program Files
(x86)\EFILive".
7. EFILive Shortcut Folder will then want you to select if you want the V8 Scan
and Tune to be accessible by all users or only the current user.
Click Next.
8. Ready to install "you are now ready to install EFILive Scan and Tune V8
Click Next.
9. EFILive will then proceed to install Scan and Tune to your desktop.
10. EFILive Scan and Tune "Installation Successful".
Click Finish.
11. EFILive Scan and Tune V8 will be located on your desktop.
Double Click EFILive Scan and Tune Icon.
12. Once opened the "tip of the day" will pop up. You may click through and
view tips or you can close out of the "tip of the day".
Click the red X for close to proceed to changing tunes.
13. Once youre in Scan and tune it will have a list of options down the left side.
F2: Scan
F3: Tune
F4: OBD
F5: BBX
"Double click here"
F6: Devices
F7: Licenses
F8: Tools
14. In the BBX Tab it will have more options down the left side of the page.
F2: Scan
F3: Tune
F4: Switch
F5: DTC's
F6: Quick Setup
"Click here"
STOCK
ECONOMY 30HP
ECOTOW 65HP
STREET 100HP
MAXXX 130HP
18. Select which tune you desire to then load onto the AutoCal.
Double click on the tune you have chosen to load onto the AutoCal.
Click "Program Quick Setup".
A "Confirm" box will pop up asking you the following.
"Re-configure FlashScan/AutoCal with the currently selected Quick
Setup options?
Existing files on FlashScan/AutoCal may be overwritten during this
process.
Continue?"
Click "Yes".
19. A progress bar will appear.
(Erasing and copying of the tunes will have a loading bar. Once the
loading bar is complete the tunes have now successfully been switched on
the AutoCal).
20. Disconnect the AutoCal from the computer and proceed to flashing the truck.
21. Plug the AutoCal into the trucks OBDII using supplied cables.
22. Turn the key to the RUN position, do not start the truck.
23. Toggle down using the right (skull) button until you see Tuning Tool. Press
the OK button (skull) in the center of the AutoCal..
24. Toggle down to Program Full press OK.
25. Toggle down until you have found your desired tune that you are wanting to
load onto the truck and press OK.
26. The screen will say Checking 0 - 100% Followed by Erasing Flashing
with a percentage % below it. This process take approximately 13 minutes.
27. When the flashing has finished, the AutoCal will prompt you to turn the
ignition off now! Turn the key off and press OK. Once the countdown has
completed you have now successfully loaded your new tune onto your truck, you
may turn the key to the run position and start the truck!