Beruflich Dokumente
Kultur Dokumente
The composite laminate plate analysis code called LamCode_2c.exe will ask for various input as described
below. Note that all stored material data sets are described in English units (lbf, in). You must give all input in
(lbf, in) units. The program will allow the definition of additional material sets, and this is described later.
1. File name where output results are to be saved. By default, this file will be in the path/folder where the code
is located; however, the output file can be any place you want (be sure to include path name if appropriate).
2. Plate dimension (L, W) in inches
3. Change in epoxy density (assumes 0.0405 lbf/in^3). You can change if desired.
4. The code has 9 material sets defined. You are asked if you want to define any additional material sets. If
you do, then you will be asked for the file name (a text file) which contains the material properties.
The materials are already defined (fiber/matrix):
1. S-Glass/epoxy
2. Woven-Glass/epoxy
3. Kevlar/epoxy
4. Carbon/epoxy
5. Graphite/epoxy
6. Boron/epoxy
7. Boron/aluminum
8. Silicon Carbide/aluminum
9. Silicon Carbide/ceramic
5. Number of layers
6. Is layup symmetric, antisymmetric or none?
7. For each layer, input Material Set #, Thickness (inches), and Theta (+CCW from x-axis). Note that if the
layup is specified as symmetric or antisymmetric, then the program will ask for only the bottom portion of
the layup and will generate the rest. Example, if number of layers is 3, and symmetric, you will only be
asked to input 2 layers.
8. Do you want to consider hygrothermal effects (yes or no)?
9. If yes, then you will be asked for the temperature change (F) and moisture fraction (0 to 1).
10. Input the force and moment resultants: N x , N y , N xy , M x , M y , M xy . Note that the units of force
resultants is lbf/in, and moment resultants is in-lbf/in. You must adhere to the sign convention for these
forces and moments as defined in the derivation of plate analysis (particularly moments, for example, M x
is a moment about the y-axis due to stress xx ).
Note: While the size of the plate is input, this information is only to calculate the weight of the plate. Since the
force and moment resultants are per unit length, the solution of stresses, strains, etc. is independent of the plate
size (i.e., the analysis is done for a unit width in the x and y directions).
WARNING ABOUT USING ONLY 1 LAYER (or a SMALL NUMBER of LAYERS): Using the code with
only 1 layer, or a very small number of layers, when there is significant bending can produce erroneous results.
With significant bending, the largest stresses (tensile or compressive) will be at the top of bottom of the plate
(with little stress at the middle of the plate). While the code calculates and outputs the stress and strain (in x-y
coordinates) at the top and bottom of each layer, and the stress and strain (in 1-2 material coordinates) at the
center of each layer, the failure criteria is only checked at the center of each layer. Consequently, if only one
layer is used and the there is significant bending which produces maximum stresses at the top or bottom of the
plate, there is a possibility that failure could occur at the extreme top or bottom of the plate, but this would not
be checked and possible failure would be overlooked by the code since the center of a plate in bending has very
low stress (and hence the failure criteria check would likely pass the test). But a visual check of actual
top/bottom stresses may actually indicate failure. One way to get around this problem is to break-up the plate
into several/many layers (each with less thickness) which then forces the code to do the failure criteria check at
locations closer to the top of bottom of the plate.
Optional material set requirements are described below.
12345678901234567890123456789012345678901234567890123456789012345678901234567890
00000000011111111112222222222333333333344444444445555555555666666666677777777778
Note: Type on column 30
Material Name (Len.le.15)::> Foam Core
E1
E2
(psi)
(psi)
::> 21.8E3
::> 21.8E3
Nu12
G12
vf
(psi)
::> 0.32
::> 4.785E3
::> 1.00
S1tu
S2tu
S12u
(ksi)
(ksi)
(ksi)
::> 0.392
::> 0.392
::> 0.1885
EP1u
EP2u
S1cu
S2cu
(ksi)
(ksi)
::> 0.01
::> 0.01
::> 0.232
::> 0.232
alpha1 (in/in/F)
alpha2
::> 0
::> 0
beta1
beta2
::> 0
::> 0
::> 0.0032
::> 0
EOF
From Matweb.com,
http://www.matweb.com/search/SpecificMaterial.asp?bassnum=PDIAB20
DIAB Divinycell HT 90 Interpenetrating Polymer Network Foam Core Material