Beruflich Dokumente
Kultur Dokumente
1 of 6)
TE41
USN
Fourth Semester B. E. Degree (Autonomous) Semester End Examination, SEE, May 2015/June 2015
Time: 3 Hours
Instructions to students:
1.
2.
3.
4.
1.
2.
a)
[8 Marks]
[6 Marks]
c) What are the differences in the working of RISC and CISC processors.
[6 Marks]
[6 Marks]
instructions to move
Immediate data 76h to register R3 of register bank 2.
[8 Marks]
[6 Marks]
number
stored in memory location 35H and store the result in next
memory location.
3.
[6 Marks]
for
programming in C? Explain with examples.
[8 Marks]
OR
4.
[10 Marks]
do you calculate
The delay length using Timers?
(Page
2 of 6)
5.
[10 Marks]
[7 Marks]
[7 Marks]
serially.
[6 Marks]
continuously at
9600 baud, 8-bit data and 1 stop bit.
OR
6.
[10 Marks]
[10 Marks]
baud continuously.
7.
a) Explain the procedure for interfacing ADC0804 with 8051 using timing
[10 Marks]
diagram.
[10 Marks]
*******
(Page
3 of 6)
TE41
USN
Fourth Semester B. E. Degree (Autonomous) Semester End Examination, SEE, May 2015/June 2015
Time: 3 Hours
Instructions to students:
1.
2.
3.
4.
1.
[8 Marks]
[6 Marks]
c)
2.
[6 Marks]
[5 Marks]
[8 Marks]
i) XCH A, direct
ii) CPL C
[7 Marks]
microcontroller
when the CALL and RET instructions are executed.
3.
[6 Marks]
b) How can we set INT0 as level triggered interrupt and INT1 as edge
[8 Marks]
triggered interrupt?
(Page
4 of 6)
[6 Marks]
OR
4.
[10 Marks]
[10 Marks]
packed BCD
and display it on port 1.
5.
a) Explain full duplex, half duplex and simplex serial data transfer.
[6 Marks]
[8 Marks]
[6 Marks]
handshaking signals.
9600 baud
continuously. Use 8 bit data and 1 stop bit.
OR
6.
[4 Marks]
b) Write an 8051 ALP to receive the data which has been sent in serial
[8 Marks]
from and send it out in parallel form. Also save the data at RAM
c)
7.
location 60H.
Explain the signals of DB-9 9-Pin connector with a relevant diagram.
[8 Marks]
a) List and explain any three commonly used LCD command codes.
[6 Marks]
[8 Marks]
[6 Marks]
*******
(Page
5 of 6)
TE41
USN
Fourth Semester B. E. Degree (Autonomous) Semester End Examination, SEE, May 2015/June 2015
Time: 3 Hours
Instructions to students:
1.
2.
3.
4.
1.
[8 Marks]
[6 Marks]
c)
2.
What are the differences in the working of RISC and CISC processors?
[6 Marks]
[6 Marks]
instructions to move
Immediate data 76h to register R3 of register bank 2.
Explain
the MUL and DIV instructions in 8051 microcontroller with
b)
examples.
c) an ALP for 8051 microcontroller to find the 2s complement of a
[8 Marks]
[6 Marks]
number
3.
[6 Marks]
(Page
6 of 6)
for
programming in C? Explain with examples.
[6 Marks]
[8 Marks]
OR
4.
[10 Marks]
do you calculate
The delay length using Timers?
[10 Marks]
5.
[7 Marks]
[7 Marks]
[6 Marks]
serially.
continuously at
9600 baud, 8-bit data and 1 stop bit.
OR
6.
7.
[10 Marks]
[10 Marks]
baud continuously.
a) Explain the procedure for interfacing ADC0804 with 8051 using timing
diagram.
b) With a connection diagram, explain how to interface DS12887 RTC
with 8051.
[10 Marks]
[10 Marks]
*******