Beruflich Dokumente
Kultur Dokumente
Contents
Contents
6 Frame Configuration .................................................................................................................6-1
6.1 Overview of Frames ......................................................................................................................................6-2
6.2 Frame Configuration .....................................................................................................................................6-3
6.2.1 Adding a Frame....................................................................................................................................6-3
6.2.2 Querying the Information of a Frame ..................................................................................................6-4
6.2.3 Adding an Inter-frame Connection.......................................................................................................6-4
6.2.4 Querying the Information about an Inter-frame Connection................................................................6-4
6.2.5 Deleting an Inter-frame Connection.....................................................................................................6-5
6.2.6 Deleting a Frame..................................................................................................................................6-5
6.3 Configuration Example .................................................................................................................................6-5
6.3.1 Networking ..........................................................................................................................................6-6
6.3.2 Adding the Frames ...............................................................................................................................6-6
Issue 02 (2007-03-20)
UA5000
Operation Manual - PVU Volume
Figures
Figures
Figure 6-1 Sample connection among the master, slave and extended frames...................................................6-6
ii
Issue 02 (2007-03-20)
UA5000
Operation Manual - PVU Volume
Tables
Tables
Table 6-1 Frames and backplanes.......................................................................................................................6-2
Table 6-2 Commands for configuring a frame....................................................................................................6-2
Issue 02 (2007-03-20)
iii
UA5000
Operation Manual - PVU Volume
6 Frame Configuration
Frame Configuration
Describes
Issue 02 (2007-03-20)
6-1
UA5000
Operation Manual - PVU Volume
6 Frame Configuration
A master frame can be connected with a slave frame and an extended frame to expand the
system capacity.
A slave frame can be connected with an extended frame to expand the system capacity.
The slave frame needs to be added using the frame add command. The slot of the slave
frame is numbered from 0.
An extended frame can be seen as a logical extension of the master frame or the slave
frame it connects. The slots are numbered sequentially with that of the mater frame or the
slave frame.
These three types of frames use different backplanes. See Table 6-1.
Backplane Type
Frame Alias
HABA
MAIN_HABM_30
HABD
MAIN_HAFM_30
HABC
MAIN_HABM_12
HABE
SLAVE_HAFS_32
HABF
6-2
To
Use
In
Add a frame
frame add
frame connect
Delete a frame
frame delete
frame set
Issue 02 (2007-03-20)
UA5000
Operation Manual - PVU Volume
6 Frame Configuration
1 : MAIN_HAFM_6(H601HABL)
2 : MAIN_HABM_30(H601HABA)
3 : MAIN_HAFM_30(H602HABD)
4 : MAIN_HABM_12(H601HABC)
5 : SLAVE_HAFS_32(H601HABE)
6 : SLAVE_HABS_32(H601HABB)
7 : SLAVE_HABS_30(H601HABA)
8 : SLAVE_HAFS_30(H601HABD)
9 : SLAVE_HAFS_30(H602HABD)
10 : SLAVE_HAFS_32(H602HABE)
11 : RSU_HAFS_30(H601HABD)
12 : RSU_HABS_30(H601HABA)
13 : RSU_HAFS_6(H601HABL)
14 : RSU_HAFS_30(H602HABD)
15 : RSP_19(HCB)
16 : RSP_15(HDB)
17 : RSP_14(HIB)
18 : RSP_12(HFB)
19 : RSP_10(HGB)
20 : RSP_6A(HMB)
21 : RSP_6B(HLB)
22 : UAM_R (HUBM)
23 : UAS_R (HUBS)
24 : UAFM_R(HUBE)
25 : UAFS_R(HUBF)
26 : UABM_R(HUBB)
27 : ONU60A_R(HUBO)
28 : UAFX_R(HUBL)
Please select frame type (0 ~ 28):0
Frame add successfully
huawei(config)#frame add 10
FrameType:
0 : MAIN_HAFM_30(H601HABD)
1 : MAIN_HAFM_6(H601HABL)
2 : MAIN_HABM_30(H601HABA)
3 : MAIN_HAFM_30(H602HABD)
4 : MAIN_HABM_12(H601HABC)
5 : SLAVE_HAFS_32(H601HABE)
6 : SLAVE_HABS_32(H601HABB)
7 : SLAVE_HABS_30(H601HABA)
8 : SLAVE_HAFS_30(H601HABD)
9 : SLAVE_HAFS_30(H602HABD)
10 : SLAVE_HAFS_32(H602HABE)
11 : RSU_HAFS_30(H601HABD)
12 : RSU_HABS_30(H601HABA)
13 : RSU_HAFS_6(H601HABL)
14 : RSU_HAFS_30(H602HABD)
15 : RSP_19(HCB)
16 : RSP_15(HDB)
17 : RSP_14(HIB)
18 : RSP_12(HFB)
19 : RSP_10(HGB)
20 : RSP_6A(HMB)
21 : RSP_6B(HLB)
22 : UAM_R (HUBM)
23 : UAS_R (HUBS)
24 : UAFM_R(HUBE)
25 : UAFS_R(HUBF)
26 : UABM_R(HUBB)
27 : ONU60A_R(HUBO)
28 : UAFX_R(HUBL)
Please select frame type (0 ~ 28):10
Frame add successfully
! FAULT MAJOR 2006-12-25 22:04:14 ALARM NAME :Frame fault
PARAMETERS :FrameID: 1
Issue 02 (2007-03-20)
6-3
UA5000
Operation Manual - PVU Volume
6 Frame Configuration
Select correct frame type when adding a frame. Otherwise, the cards in the frame may not function
normally.
A slave frame is in fault state after it is added. You need to configure the inter-frame connection for the
frame to make it work normally.
FrameType
FrameState
---------------------------------------------------------------------------0
MAIN_HAFM_30(H601HABD)
Normal
RSU_HAFS_30(H602HABD)
Failed
---------------------------------------------------------------------------Total: 2
6-4
Issue 02 (2007-03-20)
UA5000
Operation Manual - PVU Volume
6 Frame Configuration
Command:
display frame connect
--------------------------------------------Record
Upper-frame
Lower-frame
---------------------------------------------
Issue 02 (2007-03-20)
6-5
UA5000
Operation Manual - PVU Volume
6 Frame Configuration
6.3.1 Networking
Figure 6-1 shows the connection between the master frame (HABD), the slave frame (HABE)
and the extended frames (HABF).
Figure 6-1 Sample connection among the master, slave and extended frames
PSTN
E1/V5
Master frame
PP
VV
UU
D
S
L
D AA
S SS
L L L
D D
S S
L L
D
S
L
AA
SS
L L
HWOUT0
HWOUT1
HWOUT2
H
W
C
HWIN
Slave frame
D D
S S
L L
HWIN
H
W
T
D
S
L
AA
SS
L L
D D
S S
L L
D
S
L
AA
SS
LL
HWIN H
W
T
H
W
T
1 : MAIN_HAFM_6(H601HABL)
2 : MAIN_HABM_30(H601HABA)
3 : MAIN_HAFM_30(H602HABD)
4 : MAIN_HABM_12(H601HABC)
5 : SLAVE_HAFS_32(H601HABE)
6 : SLAVE_HABS_32(H601HABB)
7 : SLAVE_HABS_30(H601HABA)
8 : SLAVE_HAFS_30(H601HABD)
9 : SLAVE_HAFS_30(H602HABD)
10 : SLAVE_HAFS_32(H602HABE)
11 : RSU_HAFS_30(H601HABD)
12 : RSU_HABS_30(H601HABA)
13 : RSU_HAFS_6(H601HABL)
14 : RSU_HAFS_30(H602HABD)
15 : RSP_19(HCB)
16 : RSP_15(HDB)
17 : RSP_14(HIB)
18 : RSP_12(HFB)
19 : RSP_10(HGB)
20 : RSP_6A(HMB)
21 : RSP_6B(HLB)
22 : UAM_R (HUBM)
23 : UAS_R (HUBS)
24 : UAFM_R(HUBE)
25 : UAFS_R(HUBF)
26 : UABM_R(HUBB)
27 : ONU60A_R(HUBO)
28 : UAFX_R(HUBL)
Please select frame type (0 ~ 28): 0
6-6
Issue 02 (2007-03-20)
UA5000
Operation Manual - PVU Volume
6 Frame Configuration
You can use the display board 0 command to query the state of the card in the new frame.
Step 2 Add a slave frame, with the frame type of SLAVE_HAFS_32 (H602HABE).
huawei(config)#frame add
FrameType:
0 : MAIN_HAFM_30(H601HABD)
1 : MAIN_HAFM_6(H601HABL)
2 : MAIN_HABM_30(H601HABA)
3 : MAIN_HAFM_30(H602HABD)
4 : MAIN_HABM_12(H601HABC)
5 : SLAVE_HAFS_32(H601HABE)
6 : SLAVE_HABS_32(H601HABB)
7 : SLAVE_HABS_30(H601HABA)
8 : SLAVE_HAFS_30(H601HABD)
9 : SLAVE_HAFS_30(H602HABD)
10 : SLAVE_HAFS_32(H602HABE)
11 : RSU_HAFS_30(H601HABD)
12 : RSU_HABS_30(H601HABA)
13 : RSU_HAFS_6(H601HABL)
14 : RSU_HAFS_30(H602HABD)
15 : RSP_19(HCB)
16 : RSP_15(HDB)
17 : RSP_14(HIB)
18 : RSP_12(HFB)
19 : RSP_10(HGB)
20 : RSP_6A(HMB)
21 : RSP_6B(HLB)
22 : UAM_R (HUBM)
23 : UAS_R (HUBS)
24 : UAFM_R(HUBE)
25 : UAFS_R(HUBF)
26 : UABM_R(HUBB)
27 : ONU60A_R(HUBO)
28 : UAFX_R(HUBL)
Please select frame type (0 ~ 28):10
Frame add successfully
! FAULT MAJOR 2006-12-25 22:04:14 ALARM NAME :Frame fault
PARAMETERS :FrameID: 1
----End
Issue 02 (2007-03-20)
6-7