Beruflich Dokumente
Kultur Dokumente
HOMOLOGATION:
Truck will have certificate of conformity and / or declaration of conformity on their own
responsibility issued under the GD nr.1029 /2008 relating to the marketing of vehicles (European
Directive 98/37/EC Machinery safety). It will also have the CE marking.
GENERAL ORGANIZATION:
The special vehicle designed for intervention and rescue from heights, must be built on a chassis
equipped with a low-pollution engine and fitted with power take off (PTO) to ensure operation of
hydraulic equipment;
The engine of the special vehicle will meet the requirements of the intervention and rescue from
height systems;
Jacking facility with the possibility of leveling; the hydraulic stabilizers allow automatic lifting of
the tires from the ground, bring the truck horizontally, and return to the starting position with the
touch of a button. Withdraw any of stabilizers will be locked automatically once the arm was raised
from their movement position. The lifting of the arm from the movement position will be blocked
until the stabilizers are on the ground. The control system of the jacking facility will be mounted in
the back of the special vehicle. Control system will include a remote control command, which
allows the operator to see hydraulic stabilizers all the time. The jacking system will have two
automatic systems for operation and self control, independent, for safety to ensure the jacking in a
safe configuration. Each lower vertical stabilizer will be equipped with self-aligned foot plate to
spread the load evenly and allow operation over rough terrain.
Turntable rescue cage with telescopic arm: telescopic arm and a folding arm with the working
platform at the top; the turntable rescue cage will have a water flow system and a hydraulic system,
allowing continuous rotation of 360 degrees.
On the rescue cage will be mounted the water supply system of the platform, the supplying with
water will be possible even during the rotation of the rescue cage.
The platform is equipped with necessary technical means for intervention and protection.
The platform will be mounted on pivoting arms with the attachment point at floor level to enable the
rotation in the horizontal plane with minimum of 45 degrees left and 45 degrees right. The central
location of the platform will be indicated on the control panel.
Platform will be made of tubular steel sections profiles, welded and painted. Platform will be
equipped with an overload sensor to provide audible and visual warning on the working panels for
overcoming the cargo. It will also be equipped with a collision sensor to provide additional security.
This system will stop all movements but can be unlocked if necessary.
Firefighting equipment to allow work on the platform with water / foam discharge pipe, fixed on the
platform and with manual discharge pipes;
Command and control installation:
Main working post located at the base of the turntable ladder for executing all maneuvers, including
the possibility of taking over the secondary post controls located on the platform; Main post
incorporates all controls and safety instructions system.
Control panel will be provided with a rotating arm fixed on the rotating platform edge which can
provide convenient operating position with a very good vision, with a blocking system.
Main post will be equipped with an adjustable seat for comfort, even in case of prolonged operation.
The floor of the control post will be made of anti slip aluminum.
Control panel on the rotating platform there will be a switch to select control panel that will execute
operations (the asset);
Secondary control post located on the working platform for executing all maneuvers;
Control Panel of the secondary post from the platform will be identical to the main post control
panel, incorporating all modes of control and guidance of the safety system, thus reducing
considerably the risk of confusion among operators that are under time pressure.
Secondary station control panel shall be provided with niches for railing, to provide a more spacious
working platform. Both control panels (primary and secondary) will be equipped as standard with
minimum warning devices, indicating and monitoring, all marked by clear icons for easy
recognition as follows:
-
Starting the engine from the control panels will be blocked if the vehicle gearbox is in neutral.
Truck will be equipped with a system operated from both control panels, which will allow the arms
to be raised and working platform brought down to earth, even if there is no hydraulic pressure in
the system.
Communications facility between primary and secondary posts and between the two posts and each
crew member; Must also include a voice amplification equipment for transmission of messages.
Safety device to ensure sound signal when approaching safety margin positions and blocking
movement when reaching that limit positions;
Additional lighting installation to allow the normal visibility conditions both for control and
measuring devices, as well as at the intervention zone.
TEHNICAL SPECIFICATIONS
Special vehicle
3-axles chassis;
Vehicle category: N3
Direction: servo assist; the last axle will be self turning in order to facilitate maneuverability
in tight spaces;
3
Suspension: N3 category
Jacking system
Transport position: with min. 4 bearings; the bearings must not exceed the vehicle size;
The opening of the differential bearings (asymmetric jacking) to placement in tight spaces;
The maximum working height is measured from ground level to the work platform.
Working platform:
The construction of the platform does not allow users feet or equipment to slip out;
The access on the platform to make at least by: a rear entry. Rescue entry will be in front,
rail can be moved to the top for safe and easy access.
Automatic leveling system of the platform: continuous operation during handling whatever
arm level or position;
Additional rescue platform: vertical folding at an angle of 90; Rescue platform will be
located in front of platform automatically operating the safety railing to provide additional
safety during rescue and firefighting;
Fastening device for medical stretcher both on top (on the right or left) and in a position
intermediate (inside the platform);
Devices to ensure safety belt properly with the total number of persons admitted to working
platform: at least 3;
Safety devices at the components through which is made the access to the platform;
Secondary control post: equipped with commands, control and signaling -warning devices;
Pipe for discharge of water/foam: with the possibility of manual handling and remote from
the main control position and from the secondary;
Firefighting installation:
Supplying system:
Telescopic system with elastic links, connections and seals for transporting water and foam
to the equipment mounted on the work platform; Water pipes will be protected against
pressure with valves.
Firefighting equipments:
Possibility of water / foam discharge with both jet and jet spray;
Fix and blocked connection type B, mounted on the platform: for discharge on hose lines
equipped with manual pipes;
Command post for jacking: located in the back of the vehicle, equipped with command,
signaling and control devices;
Main command post: located at the base of the turntable cage, equipped with command,
control, signaling and communication desk, and with driver seat;
Secondary post: located on the platform, equipped with equipped with command, control,
signaling and communication desk;
TETRA mobile radio (located in the cab) with mounted antenna on the special vehicle roof;
The communication system must contain:
a) The fuse panel for all equipment including the warning devices placed next to the
accumulator which supplies the equipment;
b) 12V bipolar power sockets for communications equipment, including electrical conductors,
must bear a current of 20A and be supplied with pair connectors;
c) bipolar power outlets for installed components; shall be located in accessible places in the
cabin;
d) bipolar plugs must be properly insulated;
e) place in board for installation a car radio cassette
TETRA portable communications terminal for each crew member (3 complete);
Safety device to ensure:
Blocking the movement: if achieving of the limits of the action area and / or unnoticed
obstacle to an operator while performing maneuvers, and when the wind maximum speed
exceeds at working height;
6
Additional system for release and handling rotating cage with telescopic and folding arm
(usable system in case of failure of the main hydraulic system);
Additional lighting installation: fixed projectors for lighting the rotating cage (2 pcs.
Minimum of 70 W);
Power generator single phase (230V), sized to provide simultaneous operation of all
consumers;
Annex 1
Nr.
U/M
Quantity
Crt.
Name
1.
Cpl.
3*
2.
Compressed air cylinder made of composite material, composed of: 6,8 l cylinder at a working pressure of 300 bar with a max weight
unladen of 4,5 kg; - fillet valve
Cpl.
3**
3.
Buc.
1 sau 2
4.
Buc.
5.
Buc.
7.
B-CBC distributor
Buc.
8.
Buc.
Buc.
24V electrical device crane type (winch with lifting capacity min 200
kg at maximum working height)
Cpl.
9.
10.
11.
m.l.
m.l.
13.
Buc.
14.
Buc.
15.
Buc.
16.
Buc.
17.
Buc.
18.
Combi electric tool with with 2 batteries (one mounted on the tool and a
spare one)
Buc.
1***
19.
Charger for batteries required to operate tool combined with the ability
to feed the electrical outlets located on the working platform
Buc.
19.
20.
21.
Buc.
Buc.
Buc.
1
2
1
12.
20
(1 rol)
80
(4 role)