Beruflich Dokumente
Kultur Dokumente
www.firelite.com
DF-51500 B-400
LED
-10 Series
LED-10
GENERAL
The FireLite LED-10 Series are compact, cost-effective LED
Fire Annunciators for use with the MicroScan-5210UD tenzone Fire Alarm Control/Communicator. The LED-10 Series
consists of three models: the basic LED-10, the low-cost
LED-10L and the Canadian LED-10LS2. The LED-10(L) is
capable of illuminating Alarm (red) and Trouble (yellow) LEDs
for all ten Initiating Device Circuits (IDCs). The LED-10LS2
is primarily designed for Canadian applications, and includes
two yellow LEDs on zones 9 and 10 for annunciating supervisory conditions. The LED-10 Series also provides system
status LEDs to display Power (green), Alarm (red), Trouble
(yellow), Supervisory (yellow) and Signals Silenced (yellow).
Remote control of critical system functions, such as Reset,
Silence, Acknowledge and Drill, can be accomplished with
the model LED-10 only.
California
State Fire
Marshal
7120-0075:171
S2424
CS635
MEA
122-96-E Vol. II
FEATURES
Control Switches for System Acknowledge, Signal Silence,
Drill and Reset with enable key are included on model LED10 only (shown).
All models include system status LEDs for Power (green),
Alarm (red), Trouble (yellow), Supervisory (yellow) and
Signals Silenced (yellow).
No programming necessary.
Aesthetically pleasing, semi-flush-mount design.
Serial EIA-485 interface for reduced installation cost (see
reverse side for wiring diagram).
May be powered by 24 VDC from the host FACP or by
remote power supplies (requires filtered, regulated power).
Up to 32 LED-10 Series annunciators per MS-5210UD.
Plug-in terminal blocks for ease of installation and service.
Can be remotely located up to 6,000 feet from host control
panel.
Local piezo sounder with alarm and trouble resound.
Semi-flush-mounts to 2-3/16" deep (minimum), threegang electrical box (FireLite P/N 10103 or equivalent); or
surface-mounts to FireLite SBB-3 surface backbox.
OPERATION
The LED-10 Series annunciators provide the MS-5210UD
Conventional Fire Alarm Control/Communicator with a series of annunciators meeting most applications. All models
provide an array of LEDs to indicate system status, while the
LED-10 includes control switches for remote control of critical system functions.
LED-10
reducing wire and installation cost over traditional systems.
Four wires total are required: two for the EIA-485 communications in (twisted-pair) and two for 24 VDC regulated power.
Dip switches control local functions such as: piezo disable,
control switches/key-switch disable, transmit/receive mode.
Annunciators may be powered from the host MS-5210UD
(up to 7) or remote power supplies (requires filtered, regulated power).
LED-10
LED-10
LED-10
MS-5210UD
Notes:
1)
EIA-485: Maximum of 6,000 feet total cable length from FACP to LED-10 Series annunciators. Circuit is power limited.
2)
Up to 32 LED-10 Series annunciators may be used on the EIA-485 circuit. The MS-5210UD can power a maximum of
seven LED-10 Series annunciators. If additional LED-10 Series annunciators are connected, the FireLite FCPS-24F
may be used to supply additional power. NOTE: Power supplies used for this purpose must have their negative
terminals commoned together.
3)
Between each LED-10 Series annunciator are four wires: a twisted-shielded pair for data communications, and a pair
for 24 VDC power.
4)
Each model LED-10 (only) may have ACK, SIGNAL SILENCE, DRILL and SYSTEM RESET switches.
5)
6)
MOUNTING TO BACKBOX(ES)
CAUTION! The LED-10 Series annunciators can ONLY be
semi-flush-mounted in a three-gang electrical box with a
minimum depth of 2-3/16" (FireLite P/N 10103 or equivalent).
The LED-10 Series annunciators CANNOT be mounted in
three gangable electrical switch boxes connected together.
Mounting
Holes (4)
LED-10 flange