Beruflich Dokumente
Kultur Dokumente
(INDOOR UNIT)
FDTJ28HKXE2 FDTWJ28HKXE2B FDTSJ22HKXE2B FDRJ22HKXE2
36HKXE2
45HKXE2B
28HKXE2B
28HKXE2
45HKXE2
56HKXE2B
36HKXE2B
45HKXE2
56HKXE2
71HKXE2B
45HKXE2B
56HKXE2
71HKXE2
90HKXE2B
71HKXE2B
71HKXE2
90HKXE2
112HKXE2B
90HKXE2
112HKXE2
140HKXE2B
112HKXE2
140HKXE2
140HKXE2
FDUMJ36HKXE2 FDEJ36HKXE2B
FDKJ22HKXE2 FDFLJ28HKXE2
45HKXE2
45HKXE2B
28HKXE2
45HKXE2
56HKXE2
56HKXE2B
36HKXE2
71HKXE2
71HKXE2
71HKXE2B
45HKXE2 FDFUJ28HKXE2
90HKXE2
112HKXE2B
56HKXE2
45HKXE2
112HKXE2
140HKXE2B
71HKXE2
56HKXE2
140HKXE2
71HKXE2
723
FDC-HKX
CONTENTS
19.1 GENERAL INFORMATION ...................................................................... 725
19.1.1 Specific features ................................................................................ 725
19.1.2 How to read the model name............................................................ 727
19.1.3 Table of models ................................................................................. 727
19.1.4 Table of indoor units panel (Optional) ............................................. 727
19.2 SELECTION DATA ................................................................................... 728
19.2.1 Specifications .................................................................................... 728
19.2.2 Range of usage & limitations ........................................................... 757
19.2.3 Exterior dimensions .......................................................................... 758
19.2.4 Exterior appearance .......................................................................... 783
19.2.5 Piping system .................................................................................... 786
19.2.6 Selection chart ................................................................................... 788
19.2.7 Characteristic of fan .......................................................................... 803
19.2.8 Noise level .......................................................................................... 808
19.3 ELECTRICAL DATA ................................................................................. 814
19.3.1 Electrical wiring ................................................................................. 814
19.4 OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER ............ 824
19.5 APPLICATION DATA ............................................................................... 840
19.5.1 Installation of indoor unit ................................................................. 841
19.5.2 Installation of the remote controller (Optional Parts) .................... 882
19.5.3 Installation of outdoor unit ............................................................... 884
19.5.4 Refrigerant piping.............................................................................. 888
19.5.5 Electric wiring .................................................................................... 894
19.5.6 Test run ............................................................................................... 903
19.6 MAINTENANCE DATA ............................................................................. 904
724
FDC-HKX
19.1 GENERAL INFORMATION
19.1.1 Specific features
(1) Fuzzy control
(a)
Set temp.
Temp. difference
Gradient of temp.
operation
FUZZY operation
E.E.V. pulse
Temp.
(Return air thermistor)
30
Heating
Room air
temp.II(C)
27
FUZZY
nal
Output valve
entio
20
Room air
temp.I(C)
Conv
23
25
23
20
30
Input value
(b)
60
Time (min)
90
120
725
FDC-HKX
(5) Connectable indoor capacity
Capacity from 50% to 130% is possible.
FDCJ(P)140 type
FDCJ(P)280 type
FDCJ(P)224 type
Number of connectable units : 1 to 13 units
Connectable capacity : 11200 ~ 29200 W
(6) Cooling opetation down to -5C outdoor temperature
(7) Indoor units are available with 9 capacities, in 9 types and 54 models.
9 capacities22(0.8 HP), 28(1 HP), 36(1.25 HP), 45(1.6 HP), 56(22 HP), 71(2.5 HP), 90(3.2 HP), 112(4 HP) and 140(5 HP).
9 typesCeiling recessed type (FDT), 2-way outlet ceiling recessed type(FDTW), 1-way outlet ceiling recessed type(FDTS),
Cassetteria type(FDR), Satellite ducted type(FDUM), Ceiling suspension type(FDE), Wall mounted type(FDK) , Floor standing
exposed type(FDFL) and Floor standing hidden type (FDFU).
(8) Vertical blow or horizontal blow type can be selected for the outdoor unit.
horizontal blow
Standard
Vertical blow
Using an adapter
(Optional)
(9) Long piping design offeres One way piping length of 100 m
Indoor and outdoor units can have a level difference of up to 50 m, with a one way piping length of up to 100 m. This is the topclass long piping design in the industry. A level difference of as much as 15 m between indoor units ensures that the system can
meet a wide variety of air conditioning requirements in any building.
(10) Layout free refrigerant piping
The branch type piping makes the system flexible enough to satisfy any layout plan on the floor or in a room.
(11) Improvement of serviceability
(a)
Failures of indoor unit and outdoor units are shown on the liquid crystal display on the remote controller.
Failures of indoor unit and outdoor units can be checked by remote controller.
(b)
726
FDC-HKX
19.1.2 How to read the model name
Example:
FDC
224
KX
B
CE marking model
Application power source...See the specifications
Multi KX series
Heat pump type
Nominal capacity
P: R407C models
J: R22 models
Model name
Indoor unit
22
28
36
45
56
71
90
112
140
R407C
models
FDCP140HKXE2B
(5 Horse Power)
FDCP224HKXE2B
(8 Horse Power)
FDCP280HKXE2B
(10 Horse Power)
R22 models
FDCJ140HKXE2B
(5 Horse Power)
FDCJ224HKXE2B
(8 Horse Power)
FDCJ280HKXE2B
(10 Horse Power)
Parts Model
Capacity:28,36,45,56,
71,90,112,140
Capacity:28,45,56
Capacity:71,80
Capacity:112,140
Capacity:28,45,56
Capacity:71,90
Capacity:112,140
Capacity:22,28,36,45
Capacity:71
Capacity:22,28,45,56
Capacity:71,90
Capacity:112,140
Capacity:22,28,45,56
Capacity:71,90
Capacity:112,140
T-PSA-32W-E
TW-PSA-22W-E
TW-PSA-32W-E
TW-PSA-42W-E
TW-PSB-28W-E
TW-PSB-38W-E
TW-PSB-48W-E
TS-PSA-26W-E
TS-PSA-36W-E
R-PNLS-26W-E
R-PNLS-36W-E
R-PNLS-46W-E
R-PNLC-26W-E
R-PNLC-36W-E
R-PNLC-46W-E
727
FDC-HKX
19.2 SELECTION DATA
19.2.1 Specifications
(1) Indoor unit
(a) Ceiling recessed type (FDT)
Models FDTJ28HKXE2, 36HKXE2
Models
Item
FDTJ28HKXE2(3)
FDTJ36HKXE2(3)
3600
2800
3200
4000
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
Unit:260
kg
840
840
Panel:30
950
950
Unit:24 Panel:7
Refrigerant equipment
Heat exchanger
Refrigerant control
Turbo fan 1
Motor
17 1
Starting method
Line starting
Air flow(Standard)
CMM
Possible
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
Accessories
Decorative Panel
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
Decorative Panel model (Optional)
Item
Model
FDTJ28,36 type
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
728
FDC-HKX
Models FDTJ45HKXE2, 56HKXE2, 71HKXE2
Models
FDTJ45HKXE2(3)
FDTJ56HKXE2(3)
4500
5600
7100
5000
6300
8000
Item
1
FDTJ71HKXE2(3)
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
Unit:260
kg
840
840
Panel:30
950
950
Unit:24 Panel:7
Refrigerant equipment
Heat exchanger
Refrigerant control
Turbo fan
Motor
20 1
25 1
Starting method
Line starting
Air flow(Standard)
CMM
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
Accessories
Decorative Panel
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
Decorative Panel model (Optional)
Item
Model
FDTJ45,56,71 type
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
729
FDC-HKX
Models FDTJ90HKXE2, 112HKXE2, 140HKXE2
Models
FDTJ90HKXE2(3)
FDTJ112HKXE2(3)
9000
11200
14000
10000
12500
16000
Item
1
FDTJ140HKXE2(3)
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
kg
840
950
840
950
Unit: 320
Panel:30
Unit:24 Panel:7
Unit:28 Panel:7
Refrigerant equipment
Heat exchanger
Refrigerant control
Turbo fan
Motor
Unit:30 Panel:7
80 1
50 1
840
950
Starting method
130 1
Line starting
Air flow(Standard)
CMM
Possible
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
Accessories
Decorative Panel
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
Decorative Panel model (Optional)
Item
Model
FDTJ90,112,140 type
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
730
FDC-HKX
(b) 2-way outlet ceiling recessed type (FDTW)
Models FDTWJ28HKXE2B, 45HKXE2B, 56HKXE2B
Models
FDTWJ28HKXE2B(3)
FDTWJ45HKXE2B(3)
FDTWJ56HKXE2B(3)
2800
4500
5600
3200
5000
6300
Item
1
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
kg
Panel:8
1055
680
Unit:19 Panel:7
Refrigerant equipment
Heat exchanger
Refrigerant control
Turbo fan
30 1
CMM
Motor
Starting method
Line starting
Air flow(Standard)
Fresh air intake
Possible
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
Accessories
Decorative Panel
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
Decorative Panel model (Optional)
Item
Model
FDTWJ28,45,56 type
TW-PSA-22W-E
TW-PSB-28W-E
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
731
FDC-HKX
Models FDTWJ71HKXE2B, 90HKXE2B
Models
FDTWJ71HKXE2B(3)
Item
FDTWJ90HKXE2B(3)
7100
9000
8000
10000
dB(A)
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
Unit:330
1054
kg
620
Panel:8
1300
680
Unit:26 Panel:9
Refrigerant equipment
Heat exchanger
Refrigerant control
Turbo fan 1
Motor
35 1
40 1
Starting method
Line starting
Air flow(Standard)
CMM
Possible
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
Accessories
Decorative Panel
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
Decorative Panel model (Optional)
Item
Model
FDTWJ71,90 type
TW-PSA-32W-E
TW-PSB-38W-E
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
732
FDC-HKX
Models FDTWJ112HKXE2B, 140HKXE2B
Models
FDTWJ112HKXE2B(3)
Item
FDTWJ140HKXE2B(3)
11200
14000
12500
16000
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
Unit:345
1524
kg
620
Panel:8
1770
Unit:38 Panel:11
Refrigerant equipment
Heat exchanger
Refrigerant control
Turbo fan
Motor
680
40
2
50
Starting method
Line starting
Air flow(Standard)
CMM
Possible
2(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
Accessories
Decorative Panel
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
Decorative Panel model (Optional)
Item
Model
FDTWJ112,140 type
TW-PSA-42W-E
TW-PSB-48W-E
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
733
FDC-HKX
(c)
FDTSJ22HKXE2B(3)
FDTSJ28HKXE2B(3)
2200
2800
3600
2500
3200
4000
dB(A)
Hi: 39 Lo: 38
Item
1
FDTSJ36HKXE2B(3)
Noise level
Exterior dimensions
Height
Width
Depth
mm
Net weight
Kg
1040
650
Panel:10
1290
Unit:26 Panel:6
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan
Motor
770
35
Starting method
Line starting
Air flow(Standard)
Hi: 11 Lo: 8
CMM
Possible
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
Accessories
Decorative Panel
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
Decorative Panel model (Optional)
Item
Model
FDTSJ22,28,36 type
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for Europern nations which
require CE marking.
734
FDC-HKX
Models FDTSJ45HKXE2B, 71HKXE2B
Model
FDTSJ45HKXE2B(3)
Item
FDTSJ71HKXE2B(3)
4500
7100
5000
8000
Power source
Noise level
dB(A)
Exterior dimensions
Height
Width
Depth
Net weight
mm
kg
1040
1290
650
770
Unit:26 Panel:6
Refrigerant equipment
Heat exchanger
1300
1500
650
790
Unit:30 Panel:7
Louver fins & inner grooved tubing
Refrigerant control
Centrifugal fan 2
Motor
Centrifugal fan 4
40 1
25 2
Starting method
Line starting
Air flow(Standard)
CMM
Possible
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
Accessories
Decorative Panel
Optional parts
Outdoor units to be combined
DB
WB
DB
WB
27
19
35
24
Heating*2
20
Operation
Cooling*
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
Decorative Panel model (Optional)
Item
Model
FDTSJ45 type
TS-PSA-26W-E
FDTSJ71 type
TS-PSA-36W-E
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
735
FDC-HKX
(d) Cassetteria type (FDR)
Models FDRJ22HKXE2, 28HKXE2
Models
FDRJ22HKXE2(4)
Item
Air inlet panel
Panel model (Option)
FDRJ28HKXE2(4)
Silent panel
Canvas panel
Silent panel
Canvas panel
R-PNLS-26W-E
R-PNLC-26W-E
R-PNLS-26W-E
R-PNLC-26W-E
2200
2800
2500
3200
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
dB(A)
mm
kg
Unit:30
Panel:7
Unit:30
Panel:5
Unit:30
Panel:7
Unit:30
Panel:5
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan
Motor
40 1
50 1
Starting method
Line starting
Air flow(Standard)
CMM
Pa (mmAq)
Side or back
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
20
Operation
Heating*
Standards
ISO-T1,JIS B8616
(2)This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3)Canvas panel is used in combination with following canvas duct
Canvas duct: HA01503
(4)The number "2",following the type of each model,represents"CE-marked model"especially for European Union, and for European nations which
require CE marking.
(5)Add the canvas duct lenght to the unit height for the canvas type.
736
FDC-HKX
Models FDRJ45HKXE2, 56HKXE2
Models
FDRJ45HKXE2(4)
Item
Air inlet panel
Panel model (Option)
FDRJ56HKXE2(4)
Silent panel
Canvas panel
Silent panel
Canvas panel
R-PNLS-26W-E
R-PNLC-26W-E
R-PNLS-26W-E
R-PNLC-26W-E
4500
5600
5000
6300
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
dB(A)
mm
kg
Unit:30
Panel:7
Unit:30
Panel:5
Unit:30
Panel:7
Unit:30
Panel:5
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan
Motor
55 1
Starting method
Line starting
Air flow(Standard)
Available static pressure
( at Me)
CMM
Pa (mmAq)
Side or back
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
20
Operation
Heating*
Standards
ISO-T1,JIS B8616
(2)This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3)Canvas panel is used in combination with following canvas duct
Canvas duct: HA01503
(4)The number "2",following the type of each model,represents"CE-marked model"especially for European Union, and for Europearn nations which
require CE marking.
(5)Add the canvas duct lenght to the unit height for the canvas type.
737
FDC-HKX
Models FDRJ71HKXE2, 90HKXE2
Models
FDRJ71HKXE2(4)
Item
Air inlet panel
Panel model (Option)
FDRJ90HKXE2(4)
Silent panel
Canvas panel
Silent panel
Canvas panel
R-PNLS-36W-E
R-PNLC-36W-E
R-PNLS-36W-E
R-PNLC-36W-E
7100
9000
8000
10000
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
dB(A)
mm
kg
Unit:35
Panel:8
Unit:35
Panel:6
Unit:35
Panel:8
Unit:35
Panel:6
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan
Motor
2
100 1
90 1
Starting method
Line starting
Air flow(Standard)
CMM
Pa (mmAp)
Side or back
1(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
20
Operation
Heating*
Standards
ISO-T1,JIS B8616
(2)This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3)Canvas panel is used in combination with following canvas duct
Canvas duct: HA01490
(4)The number "2",following the type of each model,represents"CE-marked model"especially for European Union, and for European nations which
require CE marking.
(5)Add the canvas duct lenght to the unit height for the canvas type.
738
FDC-HKX
Models FDRJ112HKXE2, 140HKXE2
Models
FDRJ112HKXE2(4)
Item
Air inlet panel
Panel model (Option)
FDRJ140HKXE2(4)
Silent panel
Canvas panel
Silent panel
Canvas panel
R-PNLS-46W-E
R-PNLC-46W-E
R-PNLS-46W-E
R-PNLC-46W-E
11200
14000
12500
16000
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
dB(A)
mm
kg
Unit:50
Panel:9
Unit:50
Panel:7
Unit:52
Panel:9
Unit:52
Panel:7
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan
Motor
45 1,
90 1
50 1,
Starting method
100 1
Line starting
Air flow(Standard)
CMM
Pa (mmAq)
Side or back
2(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
20
Operation
Heating*
Standards
ISO-T1,JIS B8616
(2)This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3)Canvas panel is used in combination with following canvas duct
Canvas duct: HA01484
(4)The number "2",following the type of each model,represents"CE-marked model"especially for European Union, and for European nations which
require CE marking.
(5)Add the canvas duct lenght to the unit height for the canvas type.
739
FDC-HKX
(e)
FDUMJ36HKXE2(3)
Item
FDUMJ45HKXE2(3)
3600
4500
4000
5000
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
299
kg
750
635
34
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan 2
Motor
50 1
55 1
Starting method
Line starting
Air flow(Standard)
CMM
Pa (mmAq)
Side
_
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
_
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
740
FDC-HKX
Models FDUMJ56HKXE2, 71HKXE2, 90HKXE2
Models
Item
FDUMJ56HKXE2(3)
FDUMJ71HKXE2(3)
FDUMJ90HKXE2(3)
5600
7100
9000
6300
8000
10000
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
750
kg
635
299
34
635
40
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan 2
Motor
55 1
90 1
Starting method
100 1
Line starting
Air flow(Standard)
CMM
Pa (mmAq)
Side
_
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
_
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
741
FDC-HKX
Models FDUMJ112HKXE2, 140HKXE2
Models
FDUMJ112HKXE2(3)
Item
FDUMJ140HKXE2(3)
11200
14000
12500
16000
dB(A)
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
350
kg
1370
635
57
59
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan 3
Motor
45 1,
50 1, 100 1
90 1
Starting method
Line starting
Air flow(Standard)
Available static pressure
( at Me)
CMM
Pa (mmAq)
Side
_
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
_
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
742
FDC-HKX
(f)
FDEJ36HKXE2B(3)
FDEJ45HKXE2B(3)
3600
4500
4000
Item
1
5000
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
184
kg
1000
650
22
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan 2
Motor
40 1
CMM
Starting method
Line starting
Air flow(Standard)
Fresh air intake
Not possible
Polypropylene net
2(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
_
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
743
FDC-HKX
Models FDEJ56HKXE2B, 71HKXE2B
Models
FDEJ56HKXE2B(3)
Item
FDEJ71HKXE2B(3)
5600
7100
6300
8000
dB(A)
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
184
kg
1000
650
184
1260
22
Refrigerant equipment
Heat exchanger
Refrigerant control
650
27
Centrifugal fan 2
Centrifugal fan 4
40 1
25 2
CMM
Motor
Starting method
Line starting
Air flow(Standard)
Fresh air intake
Polypropylene net
2(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
_
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
744
FDC-HKX
Models FDEJ112HKXE2B, 140HKXE2B
Models
FDEJ112HKXE2B(3)
Item
FDEJ140HKXE2B(3)
11200
14000
12500
16000
dB(A)
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
239
kg
1260
650
239
Refrigerant control
650
40
Refrigerant equipment
Heat exchanger
Centrifugal fan
Centrifugal fan
35 1 + 55 1
CMM
Motor
1470
34
55 2
Starting method
Line starting
Air flow(Standard)
Fresh air intake
Polypropylene net
2(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
_
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
745
FDC-HKX
(g) Wall mounted type (FDK)
Models FDKJ22HKXE2, 28HKXE2, 36HKXE2, 45HKXE2
Models
FDKJ22HKXE2(3)
FDKJ28HKXE2(3)
FDKJ36HKXE2(3)
2200
2800
3600
4500
2500
3200
4000
5000
dB(A)
Hi: 40 Lo: 37
Item
1
Power source
FDKJ45HKXE2(3)
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
375
kg
930
194
19
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan 2
Motor
30 1
35 1
Starting method
Line starting
Air flow(Standard)
CMM
Hi: 9 Lo: 8
Not possible
Polypropylene net
2(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
746
FDC-HKX
Models FDKJ56HKXE2, 71HKXE2
Model
FDKJ56HKXE2(3)
FDKJ71HKXE2(3)
5600
7100
6300
Item
1
8000
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
375 1148
kg
194
375
Refrigerant control
Tangential fan 1
W
194
22
Refrigerant equipment
Heat exchanger
Motor
1436
20
Tangential fan 2
40 1
45 1
Starting method
Line starting
Air flow(Standard)
CMM
Polypropylene net
2(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
_
Accessories
Optional parts
FDCJ140HKXE2B,224HKXE2B,280HKXE2B,FDCP140HKXE2B,224HKXE2B,280HKXE2B
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
747
FDC-HKX
(h) Floor standing exposed type (FDFL)
Models FDFLJ28HKXE2, 45HKXE2, 71HKXE2
Model
Item
FDFLJ28HKXE2(3)
FDFLJ45HKXE2(3)
FDFLJ71HKXE2(3)
2800
4500
7100
3200
5000
8000
dB(A)
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
630
kg
225
630
1481
40
32
Refrigerant equipment
Heat exchanger
Refrigerant control
Centrifugal fan 2
Motor
40 1
30 1
Starting method
Line starting
Air flow(Standard)
CMM
Not possible
Polypropylene net
2(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Flare piping
Connecting method
Drain hose
Mounting kit
_
Accessories
Optional parts
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
748
225
FDC-HKX
(i) Floor standing hidden type (FDFU)
Models FDFUJ28HKXE2, 45HKXE2, 56HKXE2, 71HKXE2
Model
Item
FDFUJ28HKXE2(3)
FDFUJ45HKXE2(3)
FDFUJ56HKXE2(3)
FDFUJ71HKXE2(3)
2800
4500
5600
7100
3200
5000
6300
8000
dB(A)
Power source
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
1077
kg
225
630
Refrigerant control
Motor
225
32
25
Refrigerant equipment
Heat exchanger
1362
30 1
40 1
Starting method
Line starting
Air flow(Standard)
CMM
Not possible
Polypropylene net
2(Washable)
Polyurethane foam
Operation control
Operation switch
Thermostat by electronics
Internal thermostat for fan motor.
Frost protection thermostat
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Drain hose
Mounting kit
_
Accessories
Optional parts
DB
WB
DB
WB
Cooling*1
27
19
35
24
Heating*2
20
Operation
Standards
ISO-T1,JIS B8616
(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616"UNITARY AIR-CONDITIONERS"
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
749
FDC-HKX
(2) Outdoor unit
(a)
FDCP140HKXE2B(3)
Item
Power source
FDCP224HKXE2B(3)
FDCP280HKXE2B(3)
14000
22400
28000
16000
25000
31500
dB(A)
56
58
59
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
1450
1450
600
150
kg
Refrigerant equipment
compressor type & Q' ty
Motor
690
GT-A5539HAS51
600
250
275
GT-A5539HAS52 1
GT-A5539HS52 1
GT-A5539HAS52 1
GU-A5570HS52 1
3.5
3.5
kW
1350
Starting method
1, 2.2
3.5
1, 3.75
Capacity control
100 ~ 25
Crankcase heater
33
100 ~ 16
33
100 ~ 12
33
1, 40
Heat exchanger
Refrigerant control
Refrigerant
R407C
Quantity
kg
Refrigerant oil
12
1.45 (MA32)
2.9 (MA32)
Defrost control
3.05 (MA32)
MC controlled De-Icer
Centrifugal fan 1
Centrifugal fan 2
100 1
100 2
Starting method
Direct start
Air flow(Standard)
CMM
90
180
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Brazing
Drain
4pcs)
8pcs, 50
1pcs)
Accessories
Notes (1) The cooling and heating capabilities imply the values when the indoor unit of rated capacity is connected under the condition specified in JIS-B8616.
(2) The refrigerant quantity in the connecting pipe is not included Charge it additionally at the site.
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
Refrigerant distributor pipe set Number list (Optional)
Outdoor unit
FDCP140HKXE2B
1~8
FDCP224HKXE2B
1~13(2)
FDCP280HKXE2B
1~16(2)
Notes (1) The flow divider pipe that should be used depends on the indoor unit total downstream capacity. (1 set is required for each flow division.)
(2) When there are 13 or more indoor units there are limits on the length of the piping after the flow division, so refer to the usage range.
750
Direct start
FDC-HKX
(b) Refrigerant R22 use models
Models FDCJ140HKXE2B, 224HKXE2B, 280HKXE2B
Models
FDCJ140HKXE2B(3)
Item
Power source
FDCJ224HKXE2B(3)
FDCJ280HKXE2B(3)
14000
22400
28000
16000
25000
31500
dB(A)
56
58
59
Noise level
Exterior dimensions
Height
Width
Depth
Net weight
mm
1450
1450
600
150
kg
Refrigerant equipment
compressor type & Q' ty
Motor
690
GT-A5539EAS51
600
250
275
GT-A5539EAS52 1
GT-A5539ES52 1
GT-A5539EAS52 1
GU-A5570ES52 1
3.5
3.5
kW
1350
Starting method
1, 2.2
3.5
1, 3.75
Direct start
Capacity control
100 ~ 25
Crankcase heater
33
100 ~ 16
33
100 ~ 12
33
1, 40
Heat exchanger
Refrigerant control
Refrigerant
R22
Quantity
kg
Refrigerant oil
12
1.45 (BARREL FREEZE 32SAM) 2.9 (BARREL FREEZE 32SAM) 3.05 (BARREL FREEZE 32SAM)
Defrost control
MC controlled De-Icer
Centrifugal fan
Centrifugal fan
100 1
100 2
Starting method
Direct start
Air flow(Standard)
CMM
90
180
Safety equipment
Installation data
Refrigerant piping size
mm(in)
Connecting method
Brazing
Drain
4pcs)
8pcs,
50
1pcs)
Accessories
Notes (1) The cooling and heating capabilities imply the values when the indoor unit of rated capacity is connected under the condition specified in JIS-B8616.
(2) The refrigerant quantity in the connecting pipe is not included Charge it additionally at the site.
(3) The number "2", following the type of each model, represents"CE-marked model" especially for European Union, and for European nations which
require CE marking.
Refrigerant distributor pipe set Number list (Optional)
Outdoor unit
FDCJ140HKXE2B
1~8
: DIS-2KX10-E
FDCJ224HKXE2B
1~13(2)
: DIS-2KX20-E
FDCJ280HKXE2B
1~16(2)
Notes (1) The flow divider pipe that should be used depends on the indoor unit total downstream capacity. (1 set is required for each flow division.)
(2) When there are 13 or more indoor units there are limits on the length of the piping after the flow division, so refer to the usage range.
751
FDC-HKX
(3) Operation chart
Since the Multi KX series air conditioner units are free multitype to which the indoor units of different capacity and different
model can be combined, the operation characteristics of all combinations are very complicated, therefore only the individual
operation characteristics of indoor and outdoor units are shown. For the combined operation characteristics, calculate them with
the method shown in the next page.
(a)
FDCJ140HKXE2B
FDCJ224HKXE2B
FDCJ280HKXE2B
6.8/6.8
9.8/9.8
11.7/11.7
5.7/5.9
8.3/8.4
9.7/9.8
10.7/10.2
15.7/14.6
19.3/19.0
8.8/8.4
13.0/12.0
15.7/15.7
48
70
97/93
95/93
92/86
98/98
97/97
94/95
Cooling input
kW
Heating input
Cooling running current
(380 V/415 V)
Models
Item
FDCP140HKXE2B
FDCP224HKXE2B
FDCP280HKXE2B
6.8/6.8
9.8/9.8
11.7/11.7
6.0/6.1
9.3/9.4
11.2/11.4
10.7/10.2
15.7/14.6
19.3/19.0
9.3/8.6
14.7/14.0
17.6/16.8
Cooling input
kW
Heating input
Cooling running current
48
70
97/93
95/93
92/86
98/99
96/93
97/94
Note (1) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616 UNITARY AIR-CONDITIONERS
(220 V/240 V)
Models
Item
FDT Series
71
90
112
140
28
0.09/0.10
36
45
0.10/0.12
56
0.10/0.12
0.11/0.13
0.17/0.20
0.21/0.24
0.40/0.44
0.45/0.49
0.47/0.50
0.50/0.55
0.75/0.81
0.93/1.02
FDTW Series
(220 V/240 V)
Models
Item
FDTW Series
28
45
56
0.09/0.10
0.43/0.44
0.43/0.43
71
90
112
140
0.10/0.11
0.12/0.13
0.18/0.20
0.20/0.24
0.48/0.50
0.57/0.59
0.86/0.89
0.90/0.98
Notes (1) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616 UNITARY AIR-CONDITIONERS
(2) The values shown in the above table are common to both cooling and heating operations.
752
FDC-HKX
FDTS Series
(220 V/240 V)
Models
FDTS Series
45
71
22
0.07/0.08
0.09/0.11
0.12/0.15
0.33/0.36
0.43/0.46
0.58/0.63
Item
28
36
(220 V/240 V)
Models
Item
22
28, 36
0.09/0.11
0.11/0.13
0.41/0.46
0.51/0.56
45
56
71
90
112
140
0.14/0.16
0.15/0.17
0.16/0.19
0.24/0.28
0.28/0.32
0.63/0.67
0.68/0.71
0.73/0.79
1.07/1.17
1.28/1.32
FDE Series
(220 V/240 V)
Models
FDE Series
36
Item
45
56
71
112
140
0.10/0.11
0.12/0.15
0.20/0.24
0.24/0.29
0.43/0.46
0.58/0.63
0.90/0.98
1.10/1.20
(220 V/240 V)
Models
Item
FDK Series
22
28
36
45
56
71
28
45, 56
71
0.05/0.06
0.06/0.07
0.08/0.09
0.09/0.11
0.09/0.10
0.09/0.10
0.09/0.10
0.26/0.28
0.31/0.33
0.36/0.39
0.41/0.48
0.41/0.42
0.40/0.41
0.40/0.41
Notes (1) This packaged air-conditioner is manufactured and tested in conformity with the following standard.
JIS B8616 UNITARY AIR-CONDITIONERS
(2) The values shown in the above table are common to both cooling and heating operations.
Total power factor (%) = [Total power input (W) / 3 Total running current (A) Power source] 100
Total operation characteristics = Operation characteristic value of outdoor unit + Operation characteristic value of indoor unit
[Example]
(Conditions)
753
FDC-HKX
Operation characteristics of each unit
(Cooling/Heating)
Models
Item
FDCJ224HKXE2B
FDTJ71HKXE2
FDTJ45HKXE2
9.8/8.3
0.10/0.10
0.10/0.10
15.7/13.0
0.47/0.47
0.45/0.45
10.2 1000
3 16.9 380
.
100 =. 92 %
(Heating)
8.7 1000
3 14.2 380
.
100 =. 93 %
of compressor.
C: Power input of outdoor fan <kW>
754
FDC-HKX
1) Correction factor of compressor power input
Models FDCJ140HKXE2B, FDCP140HKXE2B
1.1
Cooling
1.0
(Rating)
0.9
Heating
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
20
40
22 28
60
80
100
120
140 160
(Rating)
180 200
182
Cooling
1.0
(Rating)
0.9
Heating
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
20 40 60 80 100 120 140 160 180 200 220 240 260 280 300
22 28
224
292
(Rating)
755
FDC-HKX
Models FDCJ280HKXE2B, FDCP280HKXEB
1.1
Cooling
1.0
(Rating)
0.9
Heating
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
50
100
150
200
22 28
250
300
280
(Rating)
350
364
400
Compressor
Outdoor fan
Outdoor unit
Cooling
Heating
FDCJ140HKXE2B
6.56/6.56
5.46/5.66
0.24/0.24
FDCJ224HKXE2B
9.33/9.33
7.83/7.93
0.47/0.47
FDCJ280HKXE2B
11.23/11.23
9.23/9.33
0.47/0.47
Compressor
Outdoor fan
Outdoor unit
Cooling
Heating
FDCP140HKXE2B
6.56/6.56
5.76/5.86
0.24/0.24
FDCP224HKXE2B
9.33/9.33
8.83/8.93
0.47/0.47
FDCP280HKXE2B
11.23/11.23
10.73/10.93
0.47/0.47
756
FDC-HKX
19.2.2 Range of usage & limitations
System
FDCP140HKXE2B
FDCJ 140HKXE2B
FDCP280HKXE2B
FDCJ280HKXE2B
FDCP224HKXE2B
FDCJ224HKXE2B
Item
Indoor intake air temperature
(Upper, lower limits)
Refer to the capacity characterstics.
1 to 8 units
1 to 13 units
1 to 16 units
70 ~ 182
112 ~ 292
140 ~ 364
Max. 40m when the connected No. of indoor unit are up to 12 units
Max. 30m when the connected No. of indoor units are 13 units or more
Max. 40m
MAX. 50m
MAX. 40m
MAX. 15m
1 cycle time
Stop time
3 min or more
Voltage fluctuation
Interval unbalance
Allowable length of refrigerant piping, height difference between indoor and outdoor unit
(1) Branch pipe method (using brancn PiPe)
Outdoor unit
Outdoor unit
denotes
MAX. 40(30)m
MAX. 15m
50m
MAX. 70m
First branch
MAX. 40(30)m
Note (1) Value in ( ) indicates when the connected No. of indoor units are 13 units or more. (FDCJ(P) 224, 280 only)
757
FDC-HKX
19.2.3 Exterior dimensions
(1) Indoor unit
(a)
Unit : mm
Decorative Panel
Holes for
suspension bolts
(M10 to M8 4pcs.)
Fresh air
opening for ducting
950
630
400
Liquid piping
28, 36, 45 type: 6.35(1/4")
56, 71, 90 type: 9.52(3/8")
Gas piping
28, 36, 45 type: 12.7(1/2")
56, 71, 90 type: 15.88(5/8")
267
332
420
637
422
Exhaust air
opening for ducting
310
Air outlet
VIEW A
840
Suspension bolts
260
VIEW B
Holes for
tapping screws
6-4.0
Holes for
tapping screws
4-4.0
55
140
25
VIEW C
1000
Obstacle
VIEW D
or more
42
140
112
100
113
140
160
33
60
80
758
30
187
137
45 or more
210
95
Lug for
suspension bolts
700 or less
(Max. Drain up)
295~325
Drain
(Connectable with VP25)
1000
or more
FDC-HKX
Models FDTJ112HKXE2, 140HKXE2
Unit : mm
Decorative Panel
Holes for
suspension bolts
(M10 to M8 4pcs.)
Fresh air
opening for ducting
950
630
400
Liquid piping
9.52(3/8")
267
332
420
637
422
Exhaust air
opening for ducting
Air outlet
310
VIEW A
Gas piping
19.05(3/4")
840
Drain
(Connectable with VP25)
Control box
55
700 or less
(Max. Drain up)
320
VIEW B
Holes for
tapping screws
6-4.0
Holes for
tapping screws
4-4.0
30
187
140
25
1000
Obstacle
or more
42
112
100
113
140
160
33
60
140
45 or more
95
137
270
295~325
1000
or more
80
VIEW C
VIEW D
759
FDC-HKX
(b) 2-way outlet ceiling recessed type (FDTW)
Models FDTWJ28HKXE2B, 45HKXE2B, 56HKXE2B
Unit : mm
Drain hose
(Accessories)
(Local setting)
278
97
50
47
64
Holes of
tapping screws
5 - 4
264
Hole
Suspension
fitting
91
Center of
panel
640
70
Suspension bolts
(M10 4 pcs.)
(Ceiling hole size)
446
Control
box
97
417
468
310
98
90
95
40
120
VIEW A
460
178
295~
325
200
200
100
Hole Hole
364
310
230
169
Hole Hole
280
140
750 or less
130
130
Liquid piping
28, 45 tipe :
6.35(1/4")
56 type :
9.52(3/8")
148
240
74
20
124
20
Drain(VP20)
(Natural drainage)
Holes for
tapping screws
8 4
20
Gas piping
28, 45type:
12.7(1/2")
56 type:
15.88(5/8")
Drain(VP25)
(condensate
pump drain)
207
240
10
620
405
178
10
20
56
Decorative Panel
1055
680
160
360
100
or more
45
760
965
45
1000or more
Air inlet
160
Air outlet
227
817
56
100
or more
Obstruction
1500
or more
1500
or more
FDC-HKX
Models FDTWJ71HKXE2B, 90HKXE2B
Unit : mm
1054
620
382
240
240
200
200
295~
325
Liquid piping
9.52(3/8")
240
Holes for
tapping screws
8 4
128
Drain (VP25)
(condensate
pump drain)
20
Drain (VP20)
(Natural drainage)
Decorative Panel
64
Gas piping
15.88(5/8")
230
750 or less
Hole
78
20
310
20
10
364
330
Hole
88
95
10
410
100
140
VIEW A
148
460
Suspension
fitting
Fresh air opening
for ducting
(knock out)
219
212
Hole
20
66
66
264
277
640
97
50
70
Center of
panel
446
Control
box
Holes of
taping screws
5 4
50
97
540
310
278
Suspension bolts
(M10 4 pcs.)
590
90
95
40
Drain hose
(Accesories)
(Local setting)
120
Air inlet
160
100
or more
1000or more
1300
Air outlet
100
or more
1500
or more
1500
or more
160
680
360
Obstruction
45
1210
45
761
FDC-HKX
Models FDTWJ112HKXE2B, 140HKXE2B
Unit: mm
310
Suspension
fitting
20
240
200
200
345
Hole
255
Hole
20
78
Holes for
tapping screws
8-4
128
Exhaust air opening for ducting
(knock out)
20
Liquid piping
9.52(3/8")
620
50
64
10 20
Gas piping
15.88(5/8")
Drain(VP25)
(condensate
pump drain)
Drain (VP20)
(Natural
drainage)
410
364
310
230
140
100
240
295~
325
10
VIEW A
163
672
234
240
Max. drain up
66
750 or less
612
103
Hole
97
1524
66
Holes for
tapping
screws
5-4
130
95
70
50
Center of
panel
Control
box
264
Suspension bolts
(M10 4 pcs.)
97
775
446
(Suspension bolts pitch)
825
90
110
40
278
Drain hose
(Accessories)
(Local setting)
1770
Air inlet
160
100
or more
1000 or more
360
680
160
Air outlet
100
or more
obstruction
45
1680
Decorative Panel
762
45
292
1500
or more
1500
or more
FDC-HKX
(c) 1-Way outlet ceiling recessed type (FDTS)
Models FDTSJ22HKXE2B, 28HKXE2B, 36HKXE2B, 45HKXE2B
35
50
25
383
25
168
Panel center
200
45
250
150
60
285
315
180
435
90
VIEW A
295~325
235
940
115
194
10
165
100
600 or less
Max. Drain up
70
Suspension bolts
(M104 pcs.)
30
30
205
85
Air outlet
920
245
Fresh air
opening for ducting
(Knock out)
85
125
40
90
290
140
60
50
100
35
770
70
45
45
1200
45
70
140
1290
Holes for
tapping screws
(4.0 6 pcs.)
VIEW B
Decorative Panel
30
45
15
650
30
415
275
100 or
more
215
1000 or more
370
Liquid piping
6.35(1/4")
100 or
more
100 or
more
110
Obstacle
155
105
555
70
290
70
60
Fresh air
opening for ducting
(knock out)
140
Fresh air
opening for ducting
(Knock out)
Unit : mm
100
50
Fresh air
opening for ducting
(Knock out)
Gas piping
12.7(1/2")
Drain (VP25)
(Condensate pump drain)
Hole for wiring
(35)
VIEW C
763
FDC-HKX
Model FDTSJ71HKXE2B
Unit : mm
70
250
60
Suspension bolts
(M104pcs.)
Drain hose(Accessories)
(Local setting)
295~325
1200
200
165
170
10 194
100
30
150
VIEW A
90
100
45
200
30
70
Fresh air
opening for ducting
(Knock out)
Air outlet
1180
210
35
60
100
770
140
50
40
90
85
110
70
290
45
70
140
Holes for
tapping screws
(4-6pcs.)
VIEW B
45
1410
45
1500
Decorative Panel
30 45
15 30
650
415
275
100 or
more
155
105
110
215
Gas piping
15.88(5/8")
VIEW C
Drain (VP25)
(Condensate pump drain)
Hole for wiring
(35)
1000 or more
370
Liquid piping
9.52(3/8")
764
140
35
50
25
168
Panel center
383
145
575
Fresh air
opening for ducting
(Knock out)
Holes for tapping screws
290
(4-6pcs.)
70
Fresh air
opening for ducting
45
(knock out)
Fresh air
opening for ducting
(knock out)
100
50
100 or
more
Obstacle
100 or
more
FDC-HKX
(d) Cassetteria type (FDR)
Model FDRJ22HKXE2
Silent Panel (Model: R-PNLS-26W-E)
Unit : mm
70
480
465
405
213
MIN95
40
MIN81
650 or less
MIN320
510
A
Drain(VP25)
(Natural drainage)
Hole for
wiring
(35)
250
460
Holes for
tapping screws
4-4.0
150
1040
45
170
170
950
Air inlet
45
75
149
45
205
635
MIN156
00
MIN225
80
355~369
295~325
405
150
Liquid piping
6.35(1/4")
MIN206
Gas piping
12.7(1/2")
345
VIEW C
Drain
(Connectable with VP25)
750
405
75
71
45
Panel center
45
59
Max. Drain up
275
69
Control box
90
Fresh air
opening for ducting
(Knock out)
510
Exhaust air
opening for ducting
(Knock out)
VIEW B
750
Suspension bolts
(M104pcs.)
Fresh air
opening for ducting
(Knock out)
284
Obstacle
more
50 or more
Air inlet
75
100 or
or more
more
1000
100 or
45
270
137
353
57
VIEW A
765
FDC-HKX
Model FDRJ22HKXE2
Canvas Panel (Model: R-PNLC -26W-E)
804 (Ceiling hole size)
284
69
45
150
193
69
Drain
(Connectable
with VP25)
Liquid piping
6.35(1/4")
Gas piping
12.7(1/2")
Control box
Panel center
352
45
Unit : mm
405
59
VIEW C
71
Max. Drain up
149
199
40
Drain (VP20)
(Natural drainage)
Canvas duct
(Optional parts)
260
405
274
35
130
465
299
405
345
480
150~300
295~325
750
635
510
600 or less
Suspension bolts
(M104pcs.)
80
Hole for
wiring
(35)
250
460
213
150
Holes for
tapping screws
864
45
170
170
Fresh air opening for ducting
(Knock out)
Air inlet
45
75
774
45
205
90
345
Air inlet
100
or more
1000 or more
Obstacle
766
100
or more
50
or more
VIEW A
75
45
VIEW B
585
149
FDC-HKX
Models FDRJ28HKXE2, 45HKXE2, 56HKXE2
Silent Panel (Model: R-PNLS-26W-E)
Unit : mm
137
Fresh air
opening for ducting
(Knock out)
(Local setting)
353
284
45
71
405
75
panel center
150
59
45
275
Control box
VIEW C
Drain
(Connectable with VP25)
Gas piping
28, 45 type: 12.7 (1/2")
56 type: 15.88 (5/8")
Liquid piping
28, 45 type: 6.35 (1/4")
56 type: 9.52 (3/8")
635
Drain (VP20)
(Natural drainage)
205
213
MIN95
Hole for wiring
(35)
250
460
Holes for
tapping screws
1040
45
45
950
Air inlet
45
150
40
MIN81
149
405
MIN156
MIN320
20
170
170
90
510
100 or
more
or more
100 or
more
50 or
Air inlet
45
VIEW B
1000
MIN225
465
MIN206
245
320
480
355~369
185
510
650 or less
295~325
750
Suspension bolts
(M10 4pcs.)
Max. Drain up
80
750
270
70
69
75
433
75
57
VIEW A
more
Obstacle
767
FDC-HKX
Models FDRJ28HKXE2, 45HKXE2, 56HKXE2
Canvas Panel (Model: R-PNLC-26W-E)
Unit : mm
Drain hose (Accessories)
(Local setting)
45
Control box
150
193
69
Drain
(Connectable with VP25)
Panel center
Liquid piping
28, 45 type: 6.35 (1/4")
56 type: 9.52 (3/8")
Gas piping
28, 45 type: 12.7 (1/2")
56 type: 15.88 (5/8")
352
45
284
59
405
VIEW C
71
149
40
405
260
35
465
199
245
130
320
480
274
185
635
510
299
295~325
750
600 or less
Suspension bolts
(M10 4pcs.)
Max. Drain up
80
00
A
205
Hole for
wiring
(35)
150~
300
Canvas duct
(Optional parts)
Drain (VP20)
(Natural drainage)
250
460
213
149
864
170
Fresh air
opening for ducting
(Knock out)
75
Air inlet
170
45
75
774
45
45
45
150
345
VIEW B
1000
100 or
more
or more
Obstacle
768
100 or
more
50 or
more
Air inlet
VIEW A
585
90
FDC-HKX
Models FDRJ71HKXE2, 90HKXE2
Silent Panel (Model: R-PNLS-36W-E)
Unit : mm
137
453
45
Panel center
71
Drain
(Connectable with VP25)
Drain (VP20)
(Natural drainage)
MIN95
MIN320
Hole
for wiring
(35)
250
460
213
205
1240
150
1150
45
170
45
Air inlet
170
45
90
510
VIEW B
750
149
Holes for
tapping screws
(4-4.0)
or more
1000 or
100
more
100 or
more
50 or
more
Air inlet
45
MIN225
405
40
20
465
MIN81
215
480
MIN156
285
635
510
355~369
285
80
MIN206
295~325
950
165
Liquid piping
9.52(3/8")
Max. Drain up
Gas piping
15.88(5/8")
Suspension bolts
(M104pcs.)
500
VIEW C
650 or less
150
45
59
75
275
270
Control box
69
70
284
75
57
Obstacle
VIEW A
769
FDC-HKX
Models FDRJ71HKXE2, 90HKXE2
Canvas Panel (Model: R-PNLC-36W-E)
Unit : mm
Drain hose (Accessories)
(Local setting)
Drain
(Connectable
with VP25)
Control box
Panel center
Liquid piping
9.52(3/8")
59
950
480
465
405
149
260
35
40
215
199
285
510
274
285
130
165
295~325
635
80
299
Suspension bolts
(M10 4pcs.)
VIEW C
Max. Drain up
71
500
Gas piping
15.88(5/8")
600 or less
193
69
150
45
9
284
352
70
Drain (VP20)
(Natural drainage)
Canvas duct
(Optional Parts)
150~300
20
Hole
for wiring
(35)
250
460
1064
45
974
Air inlet
45
170
90
VIEW B
Air inlet
VIEW A
1000
100
or more
or more
100
or more
Obstacle
770
50
or more
75
345
170
585
150
75
213
45
205
149
FDC-HKX
Models FDRJ112HKXE2, 140HKXE2
Silent Panel (Model: R-PNLS-46W-E)
Unit : mm
1600 (Ceiling hole size)
1406 (Suspension bolts pitch)
663
45
Panerl center
175
320
320
Liquid piping
19.05(3/4")
295~325
320
VIEW C
80
1370
495
Drain
(Connectable with VP25)
76
Gas piping
19.05(3/4")
Suspension bolts
(M10 4pcs.)
235
635
510
480
465
405
40
20
MIN 96
MIN156
406~420
Drain (VP20)
(Natural drainage)
MIN81
MIN206
650 or less
MIN320
MIN276
Fresh air
opening for ducting
(Knock out)
150
58
270
Control box
45
69
70
287
545
(Suspension bolts pitch)
275
75
743
57
137
Hole
for wiring
(I.D.35)
155
460
1660
75
Air inlet
45
45
1570
45
45
150
149
213
75
205
170
90
VIEW B
1000
or more
100
or more
510
750
170
100
or more
Air inlet
VIEW A
50
or more
Obstacle
771
FDC-HKX
Models FDRJ112HKXE2, 140HKXE2
Canvas Panel (Model: R-PNLC-46W-E)
Unit : mm
1424 (Ceiling hole size)
1406 (Suspension bolts pitch)
193
150
45
284
69
Control box
Drain
(Connecteble with VP25)
495
Liquid piping
9.52(3/8")
1370
465
405
295~325
86
200
235
250
320
510
325
320
635
480
350
320
130
175
600 or less
Suspension bolts
(M10 4pcs.)
80
Max. Drain up
71
VIEW C
Gas piping
19.05(3/4")
310
59
40
352
Panel center
45
70
20
Hole
for wiring
(35)
150~300
Canvas duct
(Optional parts)
A
205
149
155
Drain (VP20)
(Natural drainage)
213
150
460
1484
1394
45
45
45
Air inlet
170
170
Fresh air opening
for ducting
(Knock out)
75
or more
100
or more
1000
345
VIEW A
100
or more
Obstacle
772
50
or more
75
Air inlet
Space for installation and service
45
VIEW B
585
90
FDC-HKX
(e) Satellite ducted type (FDUM)
Models FDUMJ36HKXE2, 45HKXE2, 56HKXE2
Unit : mm
18
80
205
Hole of
tapping screws
(4-4)
284
213
149
Control box
170
Liquid piping
36, 45 type: 6.35(1/4")
56 type: 9.52(3/8")
118
472
45
18
59
Gas piping
36, 45 type: 12.7(1/2")
56 type: 15.88(5/8")
71
170
90
295~325
750
185
Max.Drain up
VIEW A
320
245
Suspension bolts
(M104pcs.)
80
30
635
510
480
465
40
149
199
274
299
600 or less
35
130
405
20
460
Drain (VP20)
(Natural drainage)
660
45
50
200
200
45
200
50
170
620
Inspection space
1100
100
35
59
630
200
35
VIEW B
773
FDC-HKX
Models FDUMJ71HKXE2, 90HKXE2
Unit : mm
986 (Suspension bolts pitch)
950
18
80
205
284
59
71
213
Holes of
tapping screws
4-4
149
Control box
118
472
(Suspension bolts pitch) 45
18
170
90
Exhaust air opening for ducting
(Knock out)
VIEW A
295~325
35
635
510
480
465
405
40
30
149
Suspension bolts
(M104pcs.)
130
80
199
215
299
274
285
Max.Drain up
285
600 or less
950
165
20
460
Drain (VP20)
(Natural drainage)
860
45
4200=800
45
50
VIEW B
774
100
1300
35
620
830
200
170
59
35
50
Inspection
space
FDC-HKX
Models FDUMJ112HKXE2, 140HKXE2
Unit : mm
1406 (Suspension bolts pitch)
1370
18
472
118 (Suspension bolts pitch) 45
18
205
80
Holes of
tapping screws
(4-4)
213
149
284
58
76
320
320
320
235
295~325
635
80
30
510
480
465
405
200
250
325
350
20
600 or less
86
130
40
Suspension bolts
(M104pcs.)
170
90
VIEW A
Max.Drain up
1370
175
150
Control box
460
Drain (VP20)
(Natural drainage)
1280
45
6200=1200
60
1250
Inspection
space
1720
35
620
100
240
210
70
35
45
60
VIEW B
775
FDC-HKX
(f)
15
15
195
275
135
46
94
184
150
50
191
50
Liquid piping
Gas piping
605
45
940
30
650
30
185
1000
Air outlet
Drain hole
connection (1)
225
248
10
290
Drain hole
connection
46
55
35
Gas piping
36, 45 type: 12.7(1/2")
56 type: 15.88(5/8")
100
or more
300
30
or more
20
150
or more
or more
Obstacles
Model FDEJ71HKXE2B
1244 (Suspension bolts pitch)
15
15
45
195
50
46
94
184
150
191
50
650
30
1200
30
185
1260
Drain hole
connection (1)
225
Air outlet
Air inlet grille
248
290
35
55
30
Gas piping
15.88(5/8")
100
or more
300
20
30
150
or more
Obstacles
776
Drain piping
connection
or more
Drain hole
connection
10
Liquid piping
9.52 (3/8")
46
or more
FDC-HKX
Model FDEJ112HKXE2B
Unit : mm
15
15
66
50
1200
30
Liguid piping
584
275
174
Gas piping
135
94
46
30
246
150
239
50
650
1260
185
225
Air outlet
266
290
Drain hole
connection
10
Liquid piping
9.52 (3/8")
46
55
Gas piping
19.05 (3/4")
30
100
or more
300
30
or more
20
150 or more
5
or more
Obstacles
Model FDEJ140HKXE2B
Unit : mm
15
15
1410
1470
30
275
Liquid piping
135
Gas piping
94
246
150
584
174
50
239
50
650
30
46
185
225
Air outlet
266
290
30
Gas piping
19.05 (3/4")
100
or more
300
55
20
35
or more
Drain hole
connection
30
10
Liquid piping
9.52 (3/8")
46
150 or more
5
or more
Obstacles
777
FDC-HKX
(g) Wall mounted type (FDK)
Models FDKJ22HKXE2, 28HKXE2, 36HKXE2, 45HKXE2
Unit : mm
950
23
387
387
130
23
194
7.7
65
155
165
10 38 50
200
Mounting plate
8 48 pcs.
(Holes on
mounting plate)
150
200
or
more
or
more
Available space
for rear connection
45
or more
155
165
820
77.5 155 77.5
25 25
20 20 25 20 20
10 64
59
65
710
65
58
90
Outlet for
electric wiring
375
280
Piping cover
Gas piping 12.7 (1/2")
Liquid piping
608 6.35 (1/4")
60 55
Drain hose
0.7 m
712
Model FDKJ56HKXE2
Unit : mm
1148
23
486
486
130
23
7.7
194
375
65
155
144
8 48 pcs.
(Holes on
mounting plate)
Available space
for rear connection
45
Piping cover
Hole on wall for
rear connection 55 Gas piping 15.88 (5/8")
105
70
Liquid piping
608 9.52 (3/8")
712
778
260
55
Drain hose
0.7 m
200
Mounting plate
or more
155
65
10 38 50
144
1018
197.5
155
197.5
25 25
20 20 25 20 20
10 64
59
908
65
58
90
280
A
Outlet for
electric wiring
150
200
or
more
or
more
FDC-HKX
Model FDKJ71HKXE2
23
Unit : mm
1436
486
387
387
130
23
194
4
7.7
155
1306
155
25 25
20 20 25 20 20
65
377.5
155
108
10 38 50
377.5
150
200
or
more
or
more
45
8 48 pcs.
(Holes on
mounting
plate)
or more
65
10 64
59
65
1196
108
58
90
Outlet for
electric wiring
375
280
Piping cover
Hole on wall for 55 Gas piping 9.52 (3/8")
rear connection
105
Liquid piping
70
608 15.88(5/8")
550
Drain hose
0.7 m
55
712
786
(1071)
205
180
23
166
10
126
600 more
225
150 more
177
Remote-controller
mounting part
1000 more
) indicates 71 type.
150 more
600 more
1196
(1481)
Control
box
80
220
184
234
315
630
250
197
223
750
(1035)
93
148
223
197
225
32
Drain piping
Flexible tube
PT20A female screw
Air filter
98
Level adjusting
screw
(Accessory)
195
806
(1091)
Liquid piping
28,45 type:6.35(1/4")
71 type:9.52(3/8")
195
779
FDC-HKX
(i) Floor standing hidden type (FDFU)
Models FDFUJ28HKXE2, 45HKXE2, 56HKXE2, 71HKXE2
Note (1) Value in (
Unit : mm
) indicates 71 type.
110
786
(1071)
167
1000
126
166
600
45
100
600
B
100
100
810(1095)
722(1007)
20
225
105 110
Control box
80
220
184
234
315
630
250
Air filter
30
197
Level adjusting
screw
(Accessory)
750(1035)
98
32
806(1091)
Unit: mm
Wall
120
Wire
(Recessed)
60
46
47
17
LCD display
120
89
83.5
Junction box
(Locally Purchased)
Remote controller outline
120
16
780
Within 100 m
Within 200 m
Within 300 m
Within 400 m
Within 600 m
Connect of
gas piping
19.05(3/4")
175
110
Anchor bolts
(M104pcs.)
Connect of
liquid piping
9.52(3/8")
239
345
428
595
50
290
40
47.5
192
131
80
Wall height H1
service
spece
suction
L2
L4
Wall height H3
170
Installation
example
0
300
Open
L2
L3
H4
Not limited
Not limited
700 or less
Not limited
Not limited
H3
Not limited
1000 or less
300
500
Not limited
Not limited
500
300
Open
(Unit: mm)
H2
29
22
H1
L4
Open
L1
Dimensions
Opening for
exit wiring
(50)
Opening for exit piping
(88)
Connect of
gas piping
19.05(3/4")
Unit: mm
Notes (1) Make sure to secure the unit with anchor bolts.
(2) When the strong wind blows, place the unit so that discharge outlet faces
the wind direction with right angle.
(3) Make sure to allow the space of 1 m or more above the unit.
(4) Connect the refrigerant piping (both gas side and liquid side) at local site.
(5) If the wall height H1, H3 of installation example III exceeds the limited value,
make sure the value of L1, L3 are to be as follows.
L1 = H1 - 500
L3 = 300 + (H3 - 700) / 2, however, if L3 exceeds 600, there is no limit for the
wall height H3.
47.5
120
112
142
50
1450
78
105
Opening for
exit piping
(88)
88
Connect of
liquid piping
9.52(3/8")
105
Opening for
exit wiring
(35)
517
690
309
532
170
70
Wall height H2
20
15
640
110
176
230
L3
L1
157
Opening for
exit wiring
(50)
100
Wall height H4
Models FDCP140HKXE2B
Models FDCJ140HKXE2B
15
102
600
FDC-HKX
781
105
Anchor bolts
(M104pcs.)
175
110
Rear surface
50
Connect of
liquid piping
12.7(1/2")
283.5
40
250
50
767
567
850
702
283.5
157
250
240
175
110
135
81
170
292
105
Opening for
exit wiring
(50)
80
Wall height H2
20
15
640
15
88
69
)
Wall height H1
service
spece
suction
Wall height H3
L4
300
Open
L3
H4
Not limited
Not limited
Not limited
Not limited
700 or less
Not limited
H3
1000 or less
300
500
H2
Not limited
500
300
Open
(Unit: mm)
H1
Not limited
L2
L4
Open
L1
Installation
example
Dimensions
22
29
Unit: mm
Notes (1) Make sure to secure the unit with anchor bolts.
(2) When the strong wind blows, place the unit so that discharge outlet faces
the wind direction with right angle.
(3) Make sure to allow the space of 1 m or more above the unit.
(4) Connect the refrigerant piping (both gas side and liquid side) at local site.
(5) If the wall height H1, H3 of installation example III exceeds the limited value,
make sure the value of L1, L3 are to be as follows.
L1 = H1 500
L3 = 300 + (H3 - 700) / 2, however, if L3 exceeds 600, there is no limit for the
wall height H3.
L2
170
Opening for
exit liquid
piping
(25)
Opening for
exit wiring
(50)
Opening for
exit piping
(88)
Connect of
liquid piping
12.7(1/2")
157
1450
70
100
123
395
123
102
L3
1350
532
L1
782
Wall height H4
600
FDC-HKX
FDC-HKX
19.2.4 Exterior appearance
(1) Indoor unit
(a)
Decorative panel
Pearl white
Air outlet
Air inlet
Decorative panel
(i) Standard type
Panel part No.
Type
Panel color
Pearl white
TW-PSA-22W-E
TW-PSA-32W-E
Applicable model
FDTW28, 45, 56 type
TW-PSA-42W-E
FDTW71, 90 type
FDTW112, 140 type
Type
Panel color
Misty white
TW-PSB-28W-E
TW-PSB-38W-E
TW-PSB-48W-E
Applicable model
FDTW28, 45, 56 type
FDTW71, 90 type
FDTW112, 140 type
783
FDC-HKX
(c)
Panel
Ceramic white
Decorative panel
Panel part No.
TS-PSA-26W-E
TS-PSA-36W-E
Type
Panel color
Misty white
Applicable model
FDTS22, 28, 36, 45 type
FDTS71 type
Ceramic white
Ceramic white
(e)
(f)
Gray
(Frame)
784
Ceramic white
(Front panel)
Ceramic white
(Air inlet louver)
Ceramic white
(Side panel)
Ceramic white
(Front panel)
FDC-HKX
(g) Wall mounted type (FDK)
No.
Parts name
Side plate
Front panel
Inlet grill
Outlet grill
Bottom plate
Color
1
1
Ceramic white
Light gray
Ceramic white
(Body)
Black
(Bottom plate)
(i)
Polar white
Polar white
785
786
Indoor B unit
Strainer
FDCP type:
Check Joint
Sub-cooling coil
Accumlator
Thermistor
(ThO-R)
Cooling cycle
Expansion
valve
Heat
exchanger
Thermistor
(ThO-A)
Heating cycle
Receiver
Solenoid valve
(SV1)
Strainer
Capillary tube
Oil separator
Check valve
Thermistor
(Tho-c)
Thermistor
Servicevalve
(Flare connecting)
Suction
Discharge
4-way valve
Service valve
(Flare connecting)
Outdoor unit
Liquid line
(12.7)
Brazing
Compressor
Electronic
expansion valve
Strainer
Gas line
(19.05)
Brazing
Check Joint
Thermistor
(ThI-A)
Capillary tube
Heat exchanger
Thermistor
(ThI-R)
Check valve
Indoor A unit
FDC-HKX
Indoor B unit
Thermistor
(ThO-D1)
Suction
Strainer
FDCP type:
Solenoid valve
(SV2)
Sub-cooling coil
Accumlator
Thermistor
(ThO-R)
Cooling cycle
Expansion
valve
Heat
exchanger
Thermistor
(ThO-A)
Heating cycle
Receiver
Solenoid valve
(SV1)
Thermistor
(ThO-D2)
Discharge
High pressure
switch(63H1-2)
(For protection)
Oil saparator
Check Joint
Thermistor
Service valve
(ThO-C)
(Flare connecting)
High
pressure
switch
(63H1-1)
(For
protection)
High pressure
switch(63H2)
(For fan
motor control)
Service valve
(Flange connecting)
Outdoor unit
Liquid line
(12.7)
Brazing
Compressor
Strainer
Capillary
tube
Strainer
Gas line
224:25.4
280:28.58
Brazing
Check Joint
Thermistor
(ThI-A)
Capillary tube
Heat exchanger
Thermistor
(ThI-R)
Indoor A unit
FDC-HKX
787
FDC-HKX
19.2.6 Selection chart
(1)
Correct the cooling and heating capacity in accordance with the conditions as follows.The net cooling and heating capacity can
be,obtained in the following way.
Indoor unit
Each indoor unit = System performance
Outdoor unit
Performance from connected capacity correction coefficient from indoor and out-
System performance = door temperature conditions (correction coefficient from piping distance correction coefficient from different between indoor and outdoor temperature) (correction coefficient from condensation when heating
Note(1) Refer to page 788 and 802 for the correction coefficient.
(a)
Cooling
1.1
1.0
Heating
0.9
0.8
0.7
0.6
43
40
35
30
25
20
26
24
0
-5
CD. B.
Heating operation
Indoor air D.B.
temperature
Cooling operation
Outdoor air D.B.
temperature
CD. B.
Applicablerange
14
16
18
20
22
Indoor air W.B. temperature C W.B. JIS Standard Condition
27
25
20
15
10
-15
-10
-5
10
JIS Standard Condition
15
(b) Correction of cooling and heating capacity in relation to one way length of refrigerant piping.
Equivalent piping length [m] (1)
Cooling
Heating
5
1.0
1.0
10
0.99
1.0
15
0.975
1.0
20
0.965
1.0
25
0.95
1.0
30
0.94
0.995
35
0.925
0.995
40
0.915
0.99
45
0.9
0.99
50
0.89
0.985
55
0.875
0.985
60
0.865
0.98
65
0.85
0.98
70
0.84
0.975
75
0.825
0.975
80
0.815
0.97
85
0.8
0.97
90
0.79
0.965
95
0.775
0.965
100
0.765
0.96
105
0.745
0.96
110
0.74
0.955
115
0.725
0.955
120
0.715
0.95
125
0.7
0.95
788
12.7
0.10
15.88
0.10
19.05
0.15
25.4
0.15
28.58
0.20
FDC-HKX
(c)
When the outdoor unit is located at a lower height than the indoor unit in cooling operation and when the
outdoor unit is located at a higher height than the indoor unit in heating operation, the following values
should be subtracvted from the values in the above table.
Height difference between the indoor unit and
outdoor unit in the vertical height difference
Adjustment coefficient
Height difference between the indoor unit and
outdoor unit in the vertical height difference
Adjustment coefficient
5m
10 m
15 m
20 m
25 m
30 m
0.01
0.02
0.03
0.04
0.05
0.06
35 m
40 m
45 m
50 m
0.07
0.08
0.09
0.10
(d) Correction of heating capacity in relation to the frost on the outdoor unit heat exchanger
Air inlet temperature of
outdoor unit in C WB
Adjustment coefficient
-15
-13
-11
-9
-7
-5
-3
-1
0.96
0.96
0.95
0.94
0.93
0.91
0.88
0.86
0.87
0.92
1.00
The correction factors will change drastically according to weather conditions. So necessary adjustment should be
made empirically according to the weather data of the particulsr area.
140
160
(Standard)
0
10
12
Rated capacity 14
Rated capacity 16
18
22
28
40
60
Heating
80
100
120
Cooling
FDCP140HKXE2B,FDCJ140HKXE2B
180
182
(2) Correction of outdoor unit capacity according to capacity of indoor unit to be operated simultaneously
789
24
25
10
12
14
16
18
20
Rated capacity
26
28
60
80 100 120 140 160 180 200 220 240 260 280
224
292
(Standard)
Cooling
22 40
28
Heating
Rated capacity
Rated capacity
790
FDCP224HKXE2B,FDCJ224HKXE2B
10
12
14
16
18
20
22
24
26
28
30
32
31.5
34
50
100
150
200
300
280
(Standard)
250
Cooling
350
364
22
28
Heating
FDCP280HKXE2B,FDCJ280HKXE2B
FDC-HKX
FDC-HKX
Capacity Correction Calculations (The procedure for both cooling and heating is the same.)
Example Conditions
Corrction when
cooling?
[Example] FDTJ90HKXE2
90 .
23.8
=. 7.65kW
280
Performance of indoor unit
FDTJ90HKXE2 ................... 7.65kW (Actual performance)
FDTJ140HKXE2 ................ 11.9kW (Actual performance)
FDTWJ28HKXE2B .......... 2.38kW (Actual performance)
FDTSJ22HKXE2B .......... 1.87kW (Actual performance)
791
FDC-HKX
(3) Sensible heat capacity
(a)
FDT Series
Model FDTJ28HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
12
27
29
31
33
35
37
39
SHC
2.58
2.55
2.52
2.49
2.46
2.43
2.40
18.0CWB
TC
2.98
2.91
2.85
2.77
2.70
2.63
2.56
SHC
2.60
2.57
2.55
2.52
2.49
2.46
2.43
19.0CWB
TC
3.05
2.99
2.92
2.86
2.80
2.72
2.64
SHC
2.61
2.59
2.56
2.54
2.52
2.49
2.46
20.0CWB
TC
3.13
3.07
3.01
2.95
2.88
2.81
2.74
SHC
2.63
2.61
2.58
2.56
2.54
2.51
2.49
21.0CWB
TC
3.21
3.15
3.09
3.02
2.95
2.89
2.83
SHC
2.64
2.62
2.60
2.58
2.55
2.53
2.51
22.0CWB
TC
3.28
3.22
3.16
3.10
3.04
2.98
2.91
SHC
2.6
2.6
2.6
2.5
2.5
2.5
2.5
Model FDTJ36HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
12
27
29
31
33
35
37
39
SHC
3.19
3.16
3.12
3.08
3.04
3.00
2.96
18.0CWB
TC
3.83
3.75
3.66
3.57
3.47
3.38
3.29
SHC
3.22
3.19
3.15
3.11
3.08
3.04
3.00
19.0CWB
TC
3.93
3.84
3.76
3.68
3.60
3.50
3.40
SHC
3.24
3.20
3.17
3.14
3.11
3.07
3.04
20.0CWB
TC
4.02
3.95
3.87
3.79
3.71
3.61
3.52
SHC
3.25
3.22
3.20
3.17
3.14
3.10
3.07
21.0CWB
TC
4.12
4.05
3.97
3.88
3.80
3.72
3.64
SHC
3.27
3.24
3.21
3.18
3.15
3.13
3.10
22.0CWB
TC
4.21
4.14
4.06
3.99
3.91
3.83
3.75
SHC
3.2
3.2
3.2
3.2
3.1
3.1
3.1
Model FDTJ45HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
15
27
29
31
33
35
37
39
SHC
3.99
3.95
3.90
3.85
3.80
3.75
3.71
18.0CWB
TC
4.78
4.68
4.58
4.46
4.34
4.23
4.11
SHC
4.02
3.98
3.94
3.89
3.85
3.80
3.76
19.0CWB
TC
4.91
4.80
4.70
4.60
4.50
4.37
4.25
SHC
4.05
4.01
3.97
3.93
3.89
3.84
3.80
20.0CWB
TC
5.03
4.93
4.83
4.73
4.64
4.52
4.40
SHC
4.07
4.03
3.99
3.96
3.92
3.88
3.84
21.0CWB
TC
5.15
5.06
4.96
4.86
4.75
4.65
4.55
SHC
4.09
4.05
4.02
3.98
3.94
3.91
3.87
22.0CWB
TC
5.27
5.18
5.08
4.98
4.88
4.78
4.68
SHC
4.1
4.0
4.0
4.0
3.9
3.9
3.9
Model FDTJ56HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
15
27
29
31
33
35
37
39
SHC
4.48
4.43
4.36
4.30
4.23
4.17
4.10
18.0CWB
TC
5.95
5.83
5.70
5.55
5.40
5.26
5.11
SHC
4.51
4.46
4.40
4.34
4.28
4.22
4.16
792
TC
SHC
19.0CWB
TC
6.11
5.98
5.85
5.72
5.60
5.44
5.29
SHC
4.53
4.47
4.42
4.37
4.32
4.26
4.19
20.0CWB
TC
6.26
6.14
6.01
5.89
5.77
5.62
5.48
SHC
4.54
4.49
4.44
4.40
4.35
4.29
4.24
21.0CWB
TC
6.41
6.30
6.18
6.04
5.91
5.78
5.66
SHC
4.55
4.51
4.46
4.41
4.36
4.32
4.27
22.0CWB
TC
6.55
6.44
6.32
6.20
6.08
5.95
5.83
SHC
4.5
4.5
4.4
4.4
4.3
4.3
4.2
FDC-HKX
Model FDTJ71KHXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
16
27
29
31
33
35
37
39
SHC
5.31
5.24
5.15
5.06
4.97
4.89
4.81
18.0CWB
TC
7.55
7.39
7.22
7.04
6.85
6.67
6.48
SHC
5.34
5.27
5.19
5.11
5.03
4.95
4.87
19.0CWB
TC
7.75
7.58
7.41
7.26
7.10
6.90
6.70
SHC
5.35
5.28
5.21
5.14
5.07
4.99
4.91
20.0CWB
TC
7.94
7.78
7.63
7.47
7.31
7.13
6.94
SHC
5.36
5.29
5.23
5.16
5.10
5.02
4.95
21.0CWB
TC
8.13
7.99
7.83
7.66
7.49
7.33
7.16
SHC
5.36
5.30
5.24
5.17
5.11
5.04
4.98
22.0CWB
TC
8.31
8.17
8.02
7.86
7.70
7.55
7.39
SHC
5.3
5.3
5.2
5.1
5.1
5.0
5.0
Model FDTJ90HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
21
27
29
31
33
35
37
39
SHC
6.82
6.72
6.62
6.51
6.39
6.29
6.19
18.0CWB
TC
9.57
9.37
9.15
8.92
8.69
8.45
8.22
SHC
6.85
6.76
6.67
6.56
6.46
6.36
6.26
19.0CWB
TC
9.82
9.60
9.40
9.20
9.00
8.75
8.50
SHC
6.87
6.78
6.69
6.61
6.52
6.42
6.31
20.0CWB
TC
10.06
9.86
9.67
9.47
9.27
9.04
8.80
SHC
6.88
6.80
6.72
6.64
6.56
6.46
6.37
21.0CWB
TC
10.31
10.13
9.93
9.71
9.50
9.30
9.10
SHC
6.89
6.82
6.74
6.65
6.57
6.49
6.42
22.0CWB
TC
10.53
10.35
10.16
9.96
9.77
9.57
9.37
SHC
6.8
6.8
6.7
6.6
6.5
6.5
6.4
Model FDTJ112HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
28
27
29
31
33
35
37
39
SHC
8.71
8.60
8.47
8.33
8.20
8.07
7.94
18.0CWB
TC
11.91
11.66
11.39
11.10
10.81
10.52
10.23
SHC
8.76
8.65
8.54
8.41
8.29
8.16
8.04
19.0CWB
TC
12.22
11.95
11.69
11.45
11.20
10.89
10.57
SHC
8.79
8.68
8.57
8.47
8.37
8.24
8.11
20.0CWB
TC
12.52
12.28
12.03
11.78
11.54
11.24
10.95
SHC
8.81
8.71
8.61
8.51
8.42
8.30
8.19
21.0CWB
TC
12.82
12.60
12.35
12.08
11.82
11.57
11.32
SHC
8.82
8.74
8.64
8.54
8.44
8.34
8.25
22.0CWB
TC
13.10
12.88
12.64
12.40
12.15
11.91
11.66
SHC
8.8
8.7
8.6
8.5
8.4
8.3
8.2
Model FDTJ140HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
30
27
29
31
33
35
37
39
SHC
10.29
10.15
9.98
9.80
9.62
9.45
9.28
18.0CWB
TC
14.88
14.57
14.24
13.87
13.51
13.15
12.78
SHC
10.34
10.20
10.04
9.88
9.72
9.55
9.40
19.0CWB
TC
15.27
14.94
14.62
14.31
14.00
13.61
13.22
SHC
10.36
10.21
10.07
9.94
9.81
9.64
9.47
20.0CWB
TC
15.65
15.34
15.04
14.73
14.42
14.06
13.69
SHC
10.37
10.24
10.11
9.98
9.85
9.70
9.55
21.0CWB
TC
16.03
15.75
15.44
15.11
14.77
14.46
14.15
SHC
10.37
10.26
10.13
10.00
9.86
9.74
9.62
22.0CWB
TC
16.38
16.10
15.81
15.50
15.19
14.88
14.57
SHC
10.3
10.2
10.1
10.0
9.8
9.7
9.6
SHC
793
FDC-HKX
(b) FDTS Series
Model FDTSJ22HKXE2B
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
11
27
29
31
33
35
37
39
SHC
2.04
2.02
2.00
1.98
1.95
1.93
1.91
18.0CWB
TC
2.34
2.29
2.24
2.18
2.12
2.07
2.01
SHC
2.06
2.04
2.02
2.00
1.98
1.95
1.93
19.0CWB
TC
2.40
2.35
2.30
2.25
2.20
2.14
2.08
SHC
2.08
2.06
2.04
2.02
2.00
1.98
1.95
20.0CWB
TC
2.46
2.41
2.36
2.31
2.27
2.21
2.15
SHC
2.09
2.07
2.05
2.03
2.02
2.00
1.98
21.0CWB
TC
2.52
2.48
2.43
2.37
2.32
2.27
2.22
SHC
2.10
2.08
2.07
2.05
2.03
2.01
2.00
22.0CWB
TC
2.57
2.53
2.48
2.44
2.39
2.34
2.29
SHC
2.11
2.09
2.08
2.06
2.04
2.03
2.01
Model FDTSJ28HKXE2B
Air flow
3
(m /min)
12
Outdoor
air temp.
17.0CWB
(CDB)
TC
2.90
2.83
2.77
2.69
2.60
2.54
2.45
27
29
31
33
35
37
39
SHC
2.58
2.55
2.52
2.49
2.46
2.43
2.40
18.0CWB
TC
2.98
2.92
2.85
2.78
2.72
2.63
2.55
SHC
2.60
2.57
2.55
2.52
2.49
2.46
2.43
19.0CWB
TC
3.06
3.00
2.93
2.87
2.80
2.73
2.65
SHC
2.62
2.59
2.57
2.54
2.52
2.49
2.46
20.0CWB
TC
3.12
3.07
3.02
2.95
2.88
2.82
2.75
SHC
2.63
2.61
2.59
2.56
2.54
2.52
2.49
21.0CWB
TC
3.21
3.14
3.09
3.04
2.97
2.90
2.83
SHC
2.64
2.62
2.60
2.58
2.56
2.54
2.51
22.0CWB
TC
3.29
3.23
3.16
3.10
3.05
2.98
2.92
SHC
2.66
2.64
2.61
2.59
2.58
2.55
2.53
Model FDTSJ36HKXE2B
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
12
27
29
31
33
35
37
39
SHC
3.20
3.16
3.13
3.09
3.04
3.01
2.96
18.0CWB
TC
3.84
3.75
3.66
3.58
3.49
3.38
3.28
SHC
3.22
3.19
3.15
3.12
3.08
3.04
3.00
19.0CWB
TC
3.94
3.86
3.77
3.69
3.60
3.51
3.41
SHC
3.24
3.21
3.18
3.15
3.11
3.08
3.04
20.0CWB
TC
4.02
3.95
3.88
3.79
3.71
3.62
3.54
SHC
3.25
3.23
3.20
3.17
3.14
3.11
3.07
21.0CWB
TC
4.13
4.04
3.97
3.90
3.82
3.73
3.64
SHC
3.27
3.24
3.21
3.19
3.16
3.13
3.10
22.0CWB
TC
4.23
4.15
4.06
3.98
3.92
3.84
3.75
SHC
3.28
3.26
3.23
3.20
3.18
3.15
3.12
Model FDTSJ45HKXE2B
Air flow
3
(m /min)
14
Outdoor
air temp.
17.0CWB
(CDB)
TC
4.66
4.55
4.45
4.33
4.19
4.08
3.94
27
29
31
33
35
37
39
SHC
3.86
3.82
3.77
3.72
3.66
3.62
3.56
18.0CWB
TC
4.80
4.69
4.58
4.47
4.37
4.22
4.10
SHC
3.89
3.85
3.80
3.76
3.71
3.66
3.61
794
TC
SHC
19.0CWB
TC
4.92
4.82
4.72
4.61
4.50
4.39
4.26
SHC
3.91
3.87
3.83
3.79
3.75
3.70
3.65
20.0CWB
TC
5.02
4.94
4.85
4.74
4.64
4.53
4.42
SHC
3.92
3.89
3.85
3.81
3.77
3.73
3.69
21.0CWB
TC
5.16
5.05
4.96
4.88
4.77
4.66
4.55
SHC
3.94
3.90
3.87
3.84
3.80
3.76
3.72
22.0CWB
TC
5.28
5.18
5.08
4.98
4.91
4.80
4.69
SHC
3.95
3.92
3.88
3.85
3.82
3.78
3.75
FDC-HKX
Model FDTSJ71HKXE2B
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
18
27
29
31
33
35
37
39
SHC
5.56
5.49
5.41
5.33
5.23
5.15
5.06
18.0CWB
TC
7.57
7.40
7.23
7.06
6.89
6.66
6.48
SHC
5.59
5.52
5.45
5.37
5.30
5.21
5.13
19.0CWB
TC
7.77
7.61
7.44
7.27
7.10
6.93
6.72
SHC
5.61
5.55
5.48
5.41
5.34
5.27
5.18
20.0CWB
TC
7.92
7.80
7.65
7.48
7.31
7.14
6.97
SHC
5.61
5.56
5.50
5.44
5.37
5.30
5.24
21.0CWB
TC
8.14
7.97
7.82
7.70
7.53
7.36
7.19
SHC
5.63
5.57
5.51
5.46
5.40
5.33
5.27
22.0CWB
TC
8.34
8.18
8.01
7.85
7.74
7.57
7.40
SHC
5.64
5.58
5.52
5.46
5.42
5.36
5.30
Outdoor
air temp.
(CDB)
10
27
29
31
33
35
37
39
SHC
2.05
2.02
2.00
1.98
1.95
1.93
1.90
18.0CWB
TC
2.35
2.29
2.24
2.19
2.13
2.06
2.01
SHC
2.06
2.04
2.02
2.00
1.98
1.95
1.93
19.0CWB
TC
2.41
2.36
2.31
2.25
2.20
2.15
2.08
SHC
2.08
2.06
2.04
2.02
2.00
1.98
1.96
20.0CWB
TC
2.46
2.42
2.37
2.32
2.27
2.21
2.16
SHC
2.09
2.07
2.06
2.04
2.02
2.00
1.98
21.0CWB
TC
2.52
2.47
2.42
2.38
2.33
2.28
2.23
SHC
2.10
2.08
2.06
2.05
2.03
2.01
2.00
22.0CWB
TC
2.58
2.53
2.48
2.43
2.40
2.35
2.29
SHC
2.11
2.09
2.08
2.06
2.05
2.03
2.01
Model FDRJ28HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
12
27
29
31
33
35
37
39
SHC
2.58
2.55
2.52
2.49
2.46
2.43
2.40
18.0CWB
TC
2.98
2.92
2.85
2.78
2.72
2.63
2.55
SHC
2.60
2.57
2.55
2.52
2.49
2.46
2.43
19.0CWB
TC
3.06
3.00
2.93
2.87
2.80
2.73
2.65
SHC
2.62
2.59
2.57
2.54
2.52
2.49
2.46
20.0CWB
TC
3.12
3.07
3.02
2.95
2.88
2.82
2.75
SHC
2.63
2.61
2.59
2.56
2.54
2.52
2.49
21.0CWB
TC
3.21
3.14
3.09
3.04
2.97
2.90
2.83
SHC
2.64
2.62
2.60
2.58
2.56
2.54
2.51
22.0CWB
TC
3.29
3.23
3.16
3.10
3.05
2.98
2.92
SHC
2.66
2.64
2.61
2.59
2.58
2.55
2.53
Model FDRJ45HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
14
27
29
31
33
35
37
39
SHC
3.86
3.82
3.77
3.72
3.66
3.62
3.56
18.0CWB
TC
4.80
4.69
4.58
4.47
4.37
4.22
4.10
SHC
3.89
3.85
3.80
3.76
3.71
3.66
3.61
19.0CWB
TC
4.92
4.82
4.72
4.61
4.50
4.39
4.26
SHC
3.91
3.87
3.83
3.79
3.75
3.70
3.65
20.0CWB
TC
5.02
4.94
4.85
4.74
4.64
4.53
4.42
SHC
3.92
3.89
3.85
3.81
3.77
3.73
3.69
21.0CWB
TC
5.16
5.05
4.96
4.88
4.77
4.66
4.55
SHC
3.94
3.90
3.87
3.84
3.80
3.76
3.72
22.0CWB
TC
5.28
5.18
5.08
4.98
4.91
4.80
4.69
SHC
3.95
3.92
3.88
3.85
3.82
3.78
3.75
SHC
795
FDC-HKX
Model FDRJ56HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
14
27
29
31
33
35
37
39
SHC
4.36
4.30
4.24
4.18
4.10
4.04
3.97
18.0CWB
TC
5.97
5.84
5.70
5.57
5.43
5.25
5.11
SHC
4.39
4.33
4.27
4.21
4.16
4.08
4.02
19.0CWB
TC
6.13
6.00
5.87
5.73
5.60
5.47
5.30
SHC
4.40
4.35
4.29
4.24
4.18
4.13
4.06
20.0CWB
TC
6.25
6.15
6.04
5.90
5.77
5.63
5.50
SHC
4.40
4.36
4.32
4.26
4.21
4.16
4.10
21.0CWB
TC
6.42
6.28
6.17
6.07
5.94
5.80
5.67
SHC
4.41
4.36
4.32
4.28
4.23
4.18
4.13
22.0CWB
TC
6.57
6.45
6.32
6.19
6.10
5.97
5.84
SHC
4.42
4.37
4.32
4.28
4.25
4.20
4.15
Model FDRJ71HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
18
27
29
31
33
35
37
39
SHC
5.56
5.49
5.41
5.33
5.23
5.15
5.06
18.0CWB
TC
7.57
7.40
7.23
7.06
6.89
6.66
6.48
SHC
5.59
5.52
5.45
5.37
5.30
5.21
5.13
19.0CWB
TC
7.77
7.61
7.44
7.27
7.10
6.93
6.72
SHC
5.61
5.55
5.48
5.41
5.34
5.27
5.18
20.0CWB
TC
7.92
7.80
7.65
7.48
7.31
7.14
6.97
SHC
5.61
5.56
5.50
5.44
5.37
5.30
5.24
21.0CWB
TC
8.14
7.97
7.82
7.70
7.53
7.36
7.19
SHC
5.63
5.57
5.51
5.46
5.40
5.33
5.27
22.0CWB
TC
8.34
8.18
8.01
7.85
7.74
7.57
7.40
SHC
5.64
5.58
5.52
5.46
5.42
5.36
5.30
Model FDRJ90HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
20
27
29
31
33
35
37
39
SHC
6.71
6.61
6.51
6.40
6.27
6.17
6.05
18.0CWB
TC
9.59
9.38
9.16
8.95
8.73
8.44
8.21
SHC
6.74
6.64
6.55
6.45
6.36
6.23
6.13
19.0CWB
TC
9.85
9.65
9.43
9.22
9.00
8.78
8.51
SHC
6.76
6.67
6.58
6.49
6.39
6.30
6.19
20.0CWB
TC
10.04
9.88
9.70
9.49
9.27
9.05
8.84
SHC
6.75
6.68
6.60
6.52
6.43
6.34
6.25
21.0CWB
TC
10.31
10.10
9.92
9.76
9.54
9.32
9.11
SHC
6.76
6.67
6.60
6.54
6.45
6.37
6.28
22.0CWB
TC
10.57
10.37
10.15
9.95
9.81
9.59
9.38
SHC
6.76
6.69
6.60
6.53
6.47
6.39
6.31
Model FDRJ112HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
28
27
29
31
33
35
37
39
SHC
8.72
8.60
8.48
8.35
8.20
8.08
7.93
18.0CWB
TC
11.94
11.67
11.40
11.13
10.86
10.51
10.21
SHC
8.77
8.66
8.54
8.42
8.31
8.16
8.04
796
TC
SHC
19.0CWB
TC
12.25
12.01
11.74
11.47
11.20
10.93
10.60
SHC
8.80
8.70
8.59
8.48
8.37
8.26
8.12
20.0CWB
TC
12.50
12.30
12.07
11.80
11.54
11.27
11.00
SHC
8.80
8.72
8.63
8.52
8.42
8.31
8.20
21.0CWB
TC
12.84
12.57
12.34
12.14
11.87
11.60
11.33
SHC
8.83
8.72
8.64
8.56
8.46
8.36
8.26
22.0CWB
TC
13.15
12.90
12.63
12.39
12.21
11.94
11.67
SHC
8.84
8.75
8.65
8.56
8.49
8.39
8.30
FDC-HKX
Model FDRJ140HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
34
27
29
31
33
35
37
39
SHC
10.78
10.63
10.48
10.31
10.12
9.97
9.78
18.0CWB
TC
14.92
14.59
14.25
13.92
13.58
13.13
12.77
SHC
10.84
10.69
10.55
10.40
10.26
10.07
9.91
19.0CWB
TC
15.32
15.01
14.67
14.34
14.00
13.66
13.24
SHC
10.88
10.75
10.60
10.46
10.32
10.19
10.01
20.0CWB
TC
15.62
15.37
15.09
14.76
14.42
14.08
13.75
SHC
10.87
10.77
10.65
10.52
10.38
10.25
10.12
21.0CWB
TC
16.04
15.71
15.43
15.18
14.84
14.50
14.17
SHC
10.90
10.77
10.66
10.56
10.43
10.30
10.18
22.0CWB
TC
16.44
16.13
15.79
15.48
15.26
14.92
14.59
SHC
10.91
10.80
10.67
10.56
10.47
10.35
10.23
12
Outdoor
air temp.
17.0CWB
(CDB)
TC
3.73
3.64
3.56
3.46
3.35
3.26
3.15
27
29
31
33
35
37
39
SHC
3.20
3.16
3.13
3.09
3.04
3.01
2.96
18.0CWB
TC
3.84
3.75
3.66
3.58
3.49
3.38
3.28
SHC
3.22
3.19
3.15
3.12
3.08
3.04
3.00
19.0CWB
TC
3.94
3.86
3.77
3.69
3.60
3.51
3.41
SHC
3.24
3.21
3.18
3.15
3.11
3.08
3.04
20.0CWB
TC
4.02
3.95
3.88
3.79
3.71
3.62
3.54
SHC
3.25
3.23
3.20
3.17
3.14
3.11
3.07
21.0CWB
TC
4.13
4.04
3.97
3.90
3.82
3.73
3.64
SHC
3.27
3.24
3.21
3.19
3.16
3.13
3.10
22.0CWB
TC
4.23
4.15
4.06
3.98
3.92
3.84
3.75
SHC
3.28
3.26
3.23
3.20
3.18
3.15
3.12
Model FDUMJ45HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
14
27
29
31
33
35
37
39
SHC
3.86
3.82
3.77
3.72
3.66
3.62
3.56
18.0CWB
TC
4.80
4.69
4.58
4.47
4.37
4.22
4.10
SHC
3.89
3.85
3.80
3.76
3.71
3.66
3.61
19.0CWB
TC
4.92
4.82
4.72
4.61
4.50
4.39
4.26
SHC
3.91
3.87
3.83
3.79
3.75
3.70
3.65
20.0CWB
TC
5.02
4.94
4.85
4.74
4.64
4.53
4.42
SHC
3.92
3.89
3.85
3.81
3.77
3.73
3.69
21.0CWB
TC
5.16
5.05
4.96
4.88
4.77
4.66
4.55
SHC
3.94
3.90
3.87
3.84
3.80
3.76
3.72
22.0CWB
TC
5.28
5.18
5.08
4.98
4.91
4.80
4.69
SHC
3.95
3.92
3.88
3.85
3.82
3.78
3.75
Model FDUMJ56HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
14
27
29
31
33
35
37
39
SHC
4.36
4.30
4.24
4.18
4.10
4.04
3.97
18.0CWB
TC
5.97
5.84
5.70
5.57
5.43
5.25
5.11
SHC
4.39
4.33
4.27
4.21
4.16
4.08
4.02
19.0CWB
TC
6.13
6.00
5.87
5.73
5.60
5.47
5.30
SHC
4.40
4.35
4.29
4.24
4.18
4.13
4.06
20.0CWB
TC
6.25
6.15
6.04
5.90
5.77
5.63
5.50
SHC
4.40
4.36
4.32
4.26
4.21
4.16
4.10
21.0CWB
TC
6.42
6.28
6.17
6.07
5.94
5.80
5.67
SHC
4.41
4.36
4.32
4.28
4.23
4.18
4.13
22.0CWB
TC
6.57
6.45
6.32
6.19
6.10
5.97
5.84
SHC
4.42
4.37
4.32
4.28
4.25
4.20
4.15
SHC
797
FDC-HKX
Model FDUMJ71HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
18
27
29
31
33
35
37
39
SHC
5.56
5.49
5.41
5.33
5.23
5.15
5.06
18.0CWB
TC
7.57
7.40
7.23
7.06
6.89
6.66
6.48
SHC
5.59
5.52
5.45
5.37
5.30
5.21
5.13
19.0CWB
TC
7.77
7.61
7.44
7.27
7.10
6.93
6.72
SHC
5.61
5.55
5.48
5.41
5.34
5.27
5.18
20.0CWB
TC
7.92
7.80
7.65
7.48
7.31
7.14
6.97
SHC
5.61
5.56
5.50
5.44
5.37
5.30
5.24
21.0CWB
TC
8.14
7.97
7.82
7.70
7.53
7.36
7.19
SHC
5.63
5.57
5.51
5.46
5.40
5.33
5.27
22.0CWB
TC
8.34
8.18
8.01
7.85
7.74
7.57
7.40
SHC
5.64
5.58
5.52
5.46
5.42
5.36
5.30
Model FDUMJ90HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
20
27
29
31
33
35
37
39
SHC
6.71
6.61
6.51
6.40
6.27
6.17
6.05
18.0CWB
TC
9.59
9.38
9.16
8.95
8.73
8.44
8.21
SHC
6.74
6.64
6.55
6.45
6.36
6.23
6.13
19.0CWB
TC
9.85
9.65
9.43
9.22
9.00
8.78
8.51
SHC
6.76
6.67
6.58
6.49
6.39
6.30
6.19
20.0CWB
TC
10.04
9.88
9.70
9.49
9.27
9.05
8.84
SHC
6.75
6.68
6.60
6.52
6.43
6.34
6.25
21.0CWB
TC
10.31
10.10
9.92
9.76
9.54
9.32
9.11
SHC
6.76
6.67
6.60
6.54
6.45
6.37
6.28
22.0CWB
TC
10.57
10.37
10.15
9.95
9.81
9.59
9.38
SHC
6.76
6.69
6.60
6.53
6.47
6.39
6.31
Model FDUMJ112HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
28
27
29
31
33
35
37
39
SHC
8.72
8.60
8.48
8.35
8.20
8.08
7.93
18.0CWB
TC
11.94
11.67
11.40
11.13
10.86
10.51
10.21
SHC
8.77
8.66
8.54
8.42
8.31
8.16
8.04
19.0CWB
TC
12.25
12.01
11.74
11.47
11.20
10.93
10.60
SHC
8.80
8.70
8.59
8.48
8.37
8.26
8.12
20.0CWB
TC
12.50
12.30
12.07
11.80
11.54
11.27
11.00
SHC
8.80
8.72
8.63
8.52
8.42
8.31
8.20
21.0CWB
TC
12.84
12.57
12.34
12.14
11.87
11.60
11.33
SHC
8.83
8.72
8.64
8.56
8.46
8.36
8.26
22.0CWB
TC
13.15
12.90
12.63
12.39
12.21
11.94
11.67
SHC
8.84
8.75
8.65
8.56
8.49
8.39
8.30
Model FDUMJ140HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
34
27
29
31
33
35
37
39
SHC
10.78
10.63
10.48
10.31
10.12
9.97
9.78
18.0CWB
TC
14.92
14.59
14.25
13.92
13.58
13.13
12.77
SHC
10.84
10.69
10.55
10.40
10.26
10.07
9.91
798
TC
SHC
19.0CWB
TC
15.32
15.01
14.67
14.34
14.00
13.66
13.24
SHC
10.88
10.75
10.60
10.46
10.32
10.19
10.01
20.0CWB
TC
15.62
15.37
15.09
14.76
14.42
14.08
13.75
SHC
10.87
10.77
10.65
10.52
10.38
10.25
10.12
21.0CWB
TC
16.04
15.71
15.43
15.18
14.84
14.50
14.17
SHC
10.90
10.77
10.66
10.56
10.43
10.30
10.18
22.0CWB
TC
16.44
16.13
15.79
15.48
15.26
14.92
14.59
SHC
10.91
10.80
10.67
10.56
10.47
10.35
10.23
FDC-HKX
(e) FDE Series
Model FDEJ36HKXE2B
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
14
27
29
31
33
35
37
39
SHC
3.34
3.30
3.26
3.23
3.18
3.15
3.10
18.0CWB
TC
3.84
3.75
3.66
3.58
3.49
3.38
3.28
SHC
3.36
3.33
3.30
3.26
3.23
3.18
3.15
19.0CWB
TC
3.94
3.86
3.77
3.69
3.60
3.51
3.41
SHC
3.39
3.36
3.32
3.29
3.26
3.23
3.19
20.0CWB
TC
4.02
3.95
3.88
3.79
3.71
3.62
3.54
SHC
3.40
3.38
3.35
3.32
3.29
3.26
3.23
21.0CWB
TC
4.13
4.04
3.97
3.90
3.82
3.73
3.64
SHC
3.42
3.39
3.37
3.34
3.31
3.28
3.25
22.0CWB
TC
4.23
4.15
4.06
3.98
3.92
3.84
3.75
SHC
3.44
3.41
3.38
3.35
3.34
3.31
3.28
Model FDEJ45HKXE2B
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
14
27
29
31
33
35
37
39
SHC
3.86
3.82
3.77
3.72
3.66
3.62
3.56
18.0CWB
TC
4.80
4.69
4.58
4.47
4.37
4.22
4.10
SHC
3.89
3.85
3.80
3.76
3.71
3.66
3.61
19.0CWB
TC
4.92
4.82
4.72
4.61
4.50
4.39
4.26
SHC
3.91
3.87
3.83
3.79
3.75
3.70
3.65
20.0CWB
TC
5.02
4.94
4.85
4.74
4.64
4.53
4.42
SHC
3.92
3.89
3.85
3.81
3.77
3.73
3.69
21.0CWB
TC
5.16
5.05
4.96
4.88
4.77
4.66
4.55
SHC
3.94
3.90
3.87
3.84
3.80
3.76
3.72
22.0CWB
TC
5.28
5.18
5.08
4.98
4.91
4.80
4.69
SHC
3.95
3.92
3.88
3.85
3.82
3.78
3.75
Model FDEJ56HKXE2B
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
14
27
29
31
33
35
37
39
SHC
4.36
4.30
4.24
4.18
4.10
4.04
3.97
18.0CWB
TC
5.97
5.84
5.70
5.57
5.43
5.25
5.11
SHC
4.39
4.33
4.27
4.21
4.16
4.08
4.02
19.0CWB
TC
6.13
6.00
5.87
5.73
5.60
5.47
5.30
SHC
4.40
4.35
4.29
4.24
4.18
4.13
4.06
20.0CWB
TC
6.25
6.15
6.04
5.90
5.77
5.63
5.50
SHC
4.40
4.36
4.32
4.26
4.21
4.16
4.10
21.0CWB
TC
6.42
6.28
6.17
6.07
5.94
5.80
5.67
SHC
4.41
4.36
4.32
4.28
4.23
4.18
4.13
22.0CWB
TC
6.57
6.45
6.32
6.19
6.10
5.97
5.84
SHC
4.42
4.37
4.32
4.28
4.25
4.20
4.15
Model FDEJ71HKXE2B
Air flow
3
(m /min)
18
Outdoor
air temp.
17.0CWB
(CDB)
TC
7.36
7.19
7.01
6.83
6.60
6.43
6.22
27
29
31
33
35
37
39
SHC
5.56
5.49
5.41
5.33
5.23
5.15
5.06
18.0CWB
TC
7.57
7.40
7.23
7.06
6.89
6.66
6.48
SHC
5.59
5.52
5.45
5.37
5.30
5.21
5.13
19.0CWB
TC
7.77
7.61
7.44
7.27
7.10
6.93
6.72
SHC
5.61
5.55
5.48
5.41
5.34
5.27
5.18
20.0CWB
TC
7.92
7.80
7.65
7.48
7.31
7.14
6.97
SHC
5.61
5.56
5.50
5.44
5.37
5.30
5.24
21.0CWB
TC
8.14
7.97
7.82
7.70
7.53
7.36
7.19
SHC
5.63
5.57
5.51
5.46
5.40
5.33
5.27
22.0CWB
TC
8.34
8.18
8.01
7.85
7.74
7.57
7.40
SHC
5.64
5.58
5.52
5.46
5.42
5.36
5.30
SHC
799
FDC-HKX
Model FDEJ112HKXE2B
Air flow
3
(m /min)
28
Outdoor
air temp.
17.0CWB
(CDB)
TC
11.60
11.33
11.07
10.77
10.42
10.15
9.81
27
29
31
33
35
37
39
SHC
8.72
8.60
8.48
8.35
8.20
8.08
7.93
18.0CWB
TC
11.94
11.67
11.40
11.13
10.86
10.51
10.21
SHC
8.77
8.66
8.54
8.42
8.31
8.16
8.04
19.0CWB
TC
12.25
12.01
11.74
11.47
11.20
10.93
10.60
SHC
8.80
8.70
8.59
8.48
8.37
8.26
8.12
20.0CWB
TC
12.50
12.30
12.07
11.80
11.54
11.27
11.00
SHC
8.80
8.72
8.63
8.52
8.42
8.31
8.20
21.0CWB
TC
12.84
12.57
12.34
12.14
11.87
11.60
11.33
SHC
8.83
8.72
8.64
8.56
8.46
8.36
8.26
22.0CWB
TC
13.15
12.90
12.63
12.39
12.21
11.94
11.67
SHC
8.84
8.75
8.65
8.56
8.49
8.39
8.30
Model FDEJ140HKXE2B
Air flow
3
(m /min)
34
(f)
Outdoor
air temp.
17.0CWB
(CDB)
TC
14.50
14.17
13.83
13.47
13.02
12.68
12.26
27
29
31
33
35
37
39
SHC
10.78
10.63
10.48
10.31
10.12
9.97
9.78
18.0CWB
TC
14.92
14.59
14.25
13.92
13.58
13.13
12.77
SHC
10.84
10.69
10.55
10.40
10.26
10.07
9.91
19.0CWB
TC
15.32
15.01
14.67
14.34
14.00
13.66
13.24
SHC
10.88
10.75
10.60
10.46
10.32
10.19
10.01
20.0CWB
TC
15.62
15.37
15.09
14.76
14.42
14.08
13.75
SHC
10.87
10.77
10.65
10.52
10.38
10.25
10.12
21.0CWB
TC
16.04
15.71
15.43
15.18
14.84
14.50
14.17
SHC
10.90
10.77
10.66
10.56
10.43
10.30
10.18
22.0CWB
TC
16.44
16.13
15.79
15.48
15.26
14.92
14.59
SHC
10.91
10.80
10.67
10.56
10.47
10.35
10.23
FDK Series
Model FDKJ22HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
27
29
31
33
35
37
39
SHC
2.04
2.02
2.00
1.98
1.95
1.93
1.91
18.0CWB
TC
2.34
2.29
2.24
2.18
2.12
2.07
2.01
SHC
2.06
2.04
2.02
2.00
1.98
1.95
1.93
19.0CWB
TC
2.40
2.35
2.30
2.25
2.20
2.14
2.08
SHC
2.08
2.06
2.04
2.02
2.00
1.98
1.95
20.0CWB
TC
2.46
2.41
2.36
2.31
2.27
2.21
2.15
SHC
2.09
2.07
2.05
2.03
2.02
2.00
1.98
21.0CWB
TC
2.52
2.48
2.43
2.37
2.32
2.27
2.22
SHC
2.10
2.08
2.07
2.05
2.03
2.01
2.00
22.0CWB
TC
2.57
2.53
2.48
2.44
2.39
2.34
2.29
SHC
2.11
2.09
2.08
2.06
2.04
2.03
2.01
Model FDKJ28HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
10
27
29
31
33
35
37
39
SHC
2.58
2.55
2.52
2.49
2.46
2.43
2.40
18.0CWB
TC
2.98
2.92
2.85
2.78
2.72
2.63
2.55
SHC
2.60
2.57
2.55
2.52
2.49
2.46
2.43
800
TC
SHC
19.0CWB
TC
3.06
3.00
2.93
2.87
2.80
2.73
2.65
SHC
2.62
2.59
2.57
2.54
2.52
2.49
2.46
20.0CWB
TC
3.12
3.07
3.02
2.95
2.88
2.82
2.75
SHC
2.63
2.61
2.59
2.56
2.54
2.52
2.49
21.0CWB
TC
3.21
3.14
3.09
3.04
2.97
2.90
2.83
SHC
2.64
2.62
2.60
2.58
2.56
2.54
2.51
22.0CWB
TC
3.29
3.23
3.16
3.10
3.05
2.98
2.92
SHC
2.66
2.64
2.61
2.59
2.58
2.55
2.53
FDC-HKX
Model FDKJ36HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
10
27
29
31
33
35
37
39
SHC
2.93
2.89
2.86
2.82
2.77
2.73
2.68
18.0CWB
TC
3.84
3.75
3.66
3.58
3.49
3.38
3.28
SHC
2.95
2.91
2.88
2.84
2.81
2.76
2.72
19.0CWB
TC
3.94
3.86
3.77
3.69
3.60
3.51
3.41
SHC
2.96
2.93
2.90
2.86
2.83
2.79
2.75
20.0CWB
TC
4.02
3.95
3.88
3.79
3.71
3.62
3.54
SHC
2.97
2.94
2.91
2.88
2.85
2.81
2.78
21.0CWB
TC
4.13
4.04
3.97
3.90
3.82
3.73
3.64
SHC
2.98
2.95
2.92
2.89
2.86
2.83
2.80
22.0CWB
TC
4.23
4.15
4.06
3.98
3.92
3.84
3.75
SHC
2.98
2.96
2.93
2.90
2.88
2.85
2.82
Model FDKJ45HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
11.5
27
29
31
33
35
37
39
SHC
3.54
3.49
3.44
3.39
3.33
3.28
3.22
18.0CWB
TC
4.80
4.69
4.58
4.47
4.37
4.22
4.10
SHC
3.56
3.51
3.46
3.42
3.37
3.31
3.26
19.0CWB
TC
4.92
4.82
4.72
4.61
4.50
4.39
4.26
SHC
3.57
3.53
3.48
3.44
3.40
3.35
3.30
20.0CWB
TC
5.02
4.94
4.85
4.74
4.64
4.53
4.42
SHC
3.57
3.54
3.50
3.46
3.42
3.37
3.33
21.0CWB
TC
5.16
5.05
4.96
4.88
4.77
4.66
4.55
SHC
3.58
3.54
3.51
3.47
3.43
3.39
3.35
22.0CWB
TC
5.28
5.18
5.08
4.98
4.91
4.80
4.69
SHC
3.59
3.55
3.51
3.47
3.45
3.41
3.37
Model FDKJ56HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
17
27
29
31
33
35
37
39
SHC
4.75
4.69
4.64
4.57
4.50
4.44
4.37
18.0CWB
TC
5.97
5.84
5.70
5.57
5.43
5.25
5.11
SHC
4.78
4.73
4.67
4.62
4.56
4.49
4.43
19.0CWB
TC
6.13
6.00
5.87
5.73
5.60
5.47
5.30
SHC
4.81
4.76
4.71
4.65
4.60
4.55
4.48
20.0CWB
TC
6.25
6.15
6.04
5.90
5.77
5.63
5.50
SHC
4.82
4.78
4.74
4.69
4.64
4.59
4.54
21.0CWB
TC
6.42
6.28
6.17
6.07
5.94
5.80
5.67
SHC
4.84
4.79
4.75
4.71
4.66
4.62
4.57
22.0CWB
TC
6.57
6.45
6.32
6.19
6.10
5.97
5.84
SHC
4.86
4.81
4.77
4.72
4.69
4.65
4.60
Model FDKJ71HKXE2
Air flow
3
(m /min)
Outdoor
air temp.
(CDB)
21
27
29
31
33
35
37
39
SHC
5.95
5.87
5.80
5.72
5.63
5.56
5.47
18.0CWB
TC
7.57
7.40
7.23
7.06
6.89
6.66
6.48
SHC
5.99
5.92
5.85
5.78
5.71
5.62
5.54
19.0CWB
TC
7.77
7.61
7.44
7.27
7.10
6.93
6.72
SHC
6.02
5.96
5.89
5.82
5.75
5.69
5.61
20.0CWB
TC
7.92
7.80
7.65
7.48
7.31
7.14
6.97
SHC
6.03
5.98
5.93
5.86
5.80
5.73
5.67
21.0CWB
TC
8.14
7.97
7.82
7.70
7.53
7.36
7.19
SHC
6.06
5.99
5.94
5.89
5.83
5.77
5.71
22.0CWB
TC
8.34
8.18
8.01
7.85
7.74
7.57
7.40
SHC
6.07
6.02
5.96
5.90
5.86
5.81
5.75
SHC
801
FDC-HKX
(g) FDFL, FDFU Series
Models FDFLJ28HKXE2, FDFUJ28HKXE2
Air flow
3
(m /min)
12
Outdoor
air temp.
17.0CWB
(CDB)
TC
2.90
2.83
2.77
2.69
2.60
2.54
2.45
27
29
31
33
35
37
39
SHC
2.58
2.55
2.52
2.49
2.46
2.43
2.40
18.0CWB
TC
2.98
2.92
2.85
2.78
2.72
2.63
2.55
SHC
2.60
2.57
2.55
2.52
2.49
2.46
2.43
19.0CWB
TC
3.06
3.00
2.93
2.87
2.80
2.73
2.65
SHC
2.62
2.59
2.57
2.54
2.52
2.49
2.46
20.0CWB
TC
3.12
3.07
3.02
2.95
2.88
2.82
2.75
SHC
2.63
2.61
2.59
2.56
2.54
2.52
2.49
21.0CWB
TC
3.21
3.14
3.09
3.04
2.97
2.90
2.83
SHC
2.64
2.62
2.60
2.58
2.56
2.54
2.51
22.0CWB
TC
3.29
3.23
3.16
3.10
3.05
2.98
2.92
SHC
2.66
2.64
2.61
2.59
2.58
2.55
2.53
14
Outdoor
air temp.
17.0CWB
(CDB)
TC
4.66
4.55
4.45
4.33
4.19
4.08
3.94
27
29
31
33
35
37
39
SHC
3.86
3.82
3.77
3.72
3.66
3.62
3.56
18.0CWB
TC
4.80
4.69
4.58
4.47
4.37
4.22
4.10
SHC
3.89
3.85
3.80
3.76
3.71
3.66
3.61
19.0CWB
TC
4.92
4.82
4.72
4.61
4.50
4.39
4.26
SHC
3.91
3.87
3.83
3.79
3.75
3.70
3.65
20.0CWB
TC
5.02
4.94
4.85
4.74
4.64
4.53
4.42
SHC
3.92
3.89
3.85
3.81
3.77
3.73
3.69
21.0CWB
TC
5.16
5.05
4.96
4.88
4.77
4.66
4.55
SHC
3.94
3.90
3.87
3.84
3.80
3.76
3.72
22.0CWB
TC
5.28
5.18
5.08
4.98
4.91
4.80
4.69
SHC
3.95
3.92
3.88
3.85
3.82
3.78
3.75
Outdoor
air temp.
(CDB)
18
27
29
31
33
35
37
39
SHC
5.56
5.49
5.41
5.33
5.23
5.15
5.06
18.0CWB
TC
7.57
7.40
7.23
7.06
6.89
6.66
6.48
SHC
5.59
5.52
5.45
5.37
5.30
5.21
5.13
802
TC
SHC
19.0CWB
TC
7.77
7.61
7.44
7.27
7.10
6.93
6.72
SHC
5.61
5.55
5.48
5.41
5.34
5.27
5.18
20.0CWB
TC
7.92
7.80
7.65
7.48
7.31
7.14
6.97
SHC
5.61
5.56
5.50
5.44
5.37
5.30
5.24
21.0CWB
TC
8.14
7.97
7.82
7.70
7.53
7.36
7.19
SHC
5.63
5.57
5.51
5.46
5.40
5.33
5.27
22.0CWB
TC
8.34
8.18
8.01
7.85
7.74
7.57
7.40
SHC
5.64
5.58
5.52
5.46
5.42
5.36
5.30
FDC-HKX
19.2.7 Characteristics of fan
(1) Cassetteria type (FDR)
Square duct
FDR45
56 type
FDR71 type
14
18
50 (5) 85 (8.5)
FDR90 type
20
50 (5) 85 (8.5)
FDR112 type
28
40 (4)
70 (7)
50 (5)
FDR140 type
34
40 (4)
70 (7)
50 (5)
90 (9)
90 (9)
20 (2)
0 (0)
20 (2)
ium
ed
12
rd
da
an
10
FDR28 type
w
Lo
FDR22 type
St
High(4)
40 (4)
StanStan- High(4)
Standard speed dard speed dard speed
Type
High(4)
1 2-spot blowout.....................
Internal resistance increases more
than the standard 3-spot blowout.
Approx. 1.4mmAq at 17m3/min
2 Square duct blowout...........
Internal resistance decreases
more than the standard round
duct (200 3-spot). 3 Pa
(0.3mmAq) at 17 m3/nin. (External static pressure increases in
reverse.)
3 Suction panel.......................
When the suction panel is not
used with the ceiling return type,
the part of internal resistance related to the panel decrease. 3 Pa
(0.3mmAq) ( = 0.60.3 ) at
20
17mm3/min.
(3)
rd
da
an h
St Hig
Standard
(2)
rd
da
an
St
Air flow
(m3 /min)
1 spot (1)
closing
Unit : Pa (mmAq)
2-spot blower
internal resistance
[Standard]
3-spot blower
internal resistance
Square duct blower
internal resistance
13 14
Notes (1) 1 spot closing: Round duct flange at center is removed and shield with a
special panel (option).
(2) Standard: 200 duct are installed at all blowout holes.
(3) Square duct: All round ducts are removed and replaced with special
square duct flanges (option).
(4) When operating at a high speed, invert the connection of white and red
connectors on the flank of control box.
16
18
Model FDRJ28HKXE2
Model FDRJ22HKXE2
120 (12)
d
ee
sp it
h
im
Hig per l
Up
100 (10)
gh
Upp
40 (4)
d
ee
sp it
h
Hig w lim
Lo
20 (2)
iu
(0) 0
[Standard]
1-spot blower internal resistance
Square duct blower internal resistance
0 (0)
(0) 0
[Standard]
2-spot blower internal resistance
Square duct blower internal resistance
gh
Hi
ard
ium
nd
ed
Sta
M
ard
nd
ig
H
Sta
Hi
ed
ow
20 (2)
ard it
w
ium
ed
Lo
ed
pe
ard
M
hs
nd
Hig w
Sta
Lo
rd
M
rd
rd
L
ed
ed
pe
h s it
g
i
m
H w li
Lo
da
da
ee
pe
gh
an
an
sp
d
Hi
da
St
gh
ee
an
40 (4)
Hi
80 (8)
sp
St
ard t
nd limi
Sta per
Up
gh
hs
60 (6)
Hi
Hig
d
ee
sp imit
h
l
g
80 (8)
Hi per
H
Up
Hi
M igh
Lo gh
e
di sp
w sp
um ee
ee
d
d
St
100 (10)
10
(2) 20
11
Upper
limit
Lower
limit
Air flow (m3/min)
(2) 20
10
12
14
15.5
Upper
limit
Lower
limit
Air flow (m3/min)
803
FDC-HKX
Models FDRJ45HKXE2, 56HKXE2
Model FDRJ71HKXE2
120 (12)
120 (12)
d
pee
h sr limit
g
i
H pe
Up
Hi
ed
M
ed
Up
ta
ow
gh
it
ium
rd
a
nd
gh
e
sp
lim
r
pe
sp
sp
Lo
w
ar
Hi
an
St
rd
ium
ed
M
rd
da
ow
20 (2)
gh
Hi
da
gh
an
d
an
gh
St
ee
40 (4)
St
Hi
ard
d
ee
lim
(0) 0
(2) 20
12
14
(2) 20
15.5
Upper
limit
Model FDRJ90HKXE2
13 14
Lower
limit
16
18
Air flow (m3/min)
20
Upper
limit
Model FDRJ112HKXE2
120 (12)
120 (12)
100 (10)
100 (10)
gh
ee
sp
gh
sp
d
M
ed
ium
sp
gh
ow
li
St
ed
60 (6)
Me
it
diu
sp
ee
Lo
h
Hig
w
Lo
ed
St
spe
da
rd
H
igh
St
da
an
diu
w
Lo
Me
rd
ar
20 (2)
lim
an
40 (4)
3-spot blower
internal resistance
m
(0) 0
sp
ee
d
Hi
gh
igh
diu
Me
0 (0)
sp
ee
rd
nda
t
Sta er limi
H
Upp
d
an
igh
H
rd
rd
nda
ow
L
rd
2-spot blower
internal resistance
Hi
gh
St
da
an
Hi
Sta
da
20 (2)
t
mi
ee
d
ee
n
Sta
40 (4)
80 (8)
gh
Hi
d
Hi
e
sp
gh
Hi ow
L
ard t
nd limi
a
t
r
S pe
Up
d
ee
sp mit
h
i
l
Hig per
Up
Hi
gh
Hi
d
ee
sp mit
h
i
Hig per l
Up
80 (8)
Hi
gh
it
60 (6)
0 (0)
(0) 0
[Standard]
2-spot blower internal resistance
Square duct blower internal resistance
60 (6)
Hi
nd
0 (0)
10
Lower
limit
e
pe
Hi
gh
lim
Sta
m
diu
Me
rd
nda
Sta
w
Lo
rd
da
n
Sta
Hi
ium
40 (4)
gh
Hi
d
ee
sp
ed
M
ed
h
Hig
gh
ee
dU
80 (8)
it
w
Lo
ed
e
sp
lim
r
pe
Hi
sp
e
sp
imit
er l
p
Up
ard
60 (6) Stand
20 (2)
it
gh
gh
Hi
rd
da
an
St w
Lo
80 (8)
100 (10)
100 (10)
0 (0)
(2) 20
14
Lower
limit
804
20
17
20 (2)
22
Upper
limit
21 22
Lower
limit
25
28
3
31
Upper
limit
FDC-HKX
Model FDRJ140HKXE2
120 (12)
d
ee
sp
ed
M
d
m
iu
gh
d
ee
sp
60 (6)
da
an
St
Lo
d
ee
sp it
h
g
m
Hi w li
Lo
a
St
40 (4)
h
ig
H
ee
rd t
da limi
n
a r
St ppe
U
Hi
H
rd
igh
20 (2)
e
M
rd
da
Lo
d
ar
an
St
nd
h
ig
H
sp
80 (8)
gh
Hi
ed
pe it
s
m
gh li
Hi per
p
U
100 (10)
diu
3-spot blower
internal resistance
(0) 0
0 (0)
24
Lower
limit
26
30
34
3
(2) 20
38
Upper
limit
805
FDC-HKX
(2) Satellite ducted type (FDUM)
External static pressure table
Duct specs.
1 spot
closing
Standard
Square duct
FDUM90 type
20
FDUM112 type
28
50 (5)
FDUM140 type
34
18
35 (3.5) 70 (7)
90 (9)
80 (8)
60 (6)
Note (1) For high speed operation, insert the white connector and the red
connector beside the control box in other places respectively.
rd
da
an um
St edi
M
90 (9)
Lo
rd
14
da
12
an
FDUM36 type
FDUM45
56 type
FDUM71 type
St
Type
rd
da
an gh
St Hi
Air flow
(m3 /min)
Unit : Pa (mmAq)
20 (2)
2-spot blower
internal resistance
0 (0)
10 (1)
3-spot blower
internal resistance
Square duct blower
internal resistance
20 (2)
13 14
16
18
20
1 2-spot blowout.....................
Internal resistance increases more than
the standard 3-spot blowout. Approx.
14Pa (1.4mmAq) at 17m3/min
2 Square duct blowout...........
Internal resistance decreases more than
the standard round duct (200 3-spot).
3Pa (0.3mmAq) at 17 m3/min.
(External static pressure increases in
reverse.)
Model FDUMJ36HKXE2
er
pp
100 (10)
U
d
t
imi
spe
100 (10)
ed
M
ium
0 (0)
10 (1)
20 (2)
806
12
3
igh
H
ard
nd
rd
20 (2)
10
ard
nd
Sta
40 (4)
0 (0)
Lower
limit
gh
ium
d
ee
sp it
h
Hig w lim
Lo
Sta
Hi
it
lim
d
Me
d
er
p
Up
a
nd
Sta w
Lo
igh
H
ard
nd
ium
Sta
ed
M
ard
nd
Sta
w
Lo
rd
ee
ard
nd
Sta
ee
sp
60 (6)
sp
gh
sp
ow
lim
dL
it
w
Lo
ed
a
nd
Sta
h
Hig
Hi
ee
80 (8)
gh
ium
ed
ed
M
pe
ed
hs
Hig w
Lo
20 (2)
sp
Hi
d
gh
ee
pe
hs
40 (4)
Hi
sp
Hig
ard
nd limit
a
t
S per
Up
gh
gh
Hi
80 (8)
Hi
ed
spe it
h
m
Hig per li
Up
h
Hig
14
10
Upper
limit
Lower
limit
12
14
3
15.5
Upper
limit
FDC-HKX
Model FDUMJ71HKXE2
Model FDUMJ90HKXE2
120 (12)
120 (12)
100 (10)
100 (10)
ee
gh
Hi
rd
da
an
ow
St
L
d
40 (4)
nda
ium
ed
20 (2)
Me
rd
Lo
ard
M
rd
nd
da
Sta
d
ee
p
s it
gh lim
Hi w
Lo
Sta
an
60 (6) Sta
sp
St
m
iu
ed
M
d
ee
sp
Up
rd
a
nd
gh
m
iu
diu
0 (0)
it
lim
r
pe
Hi
ed
M
d
Lo
d
ee
sp
r
da
an
St w
Lo
20 (2)
h
ig
H
gh
ee
d
ee
sp it
h
ig lim
H ow
L
gh
Hi
40 (4)
gh
Hi
Hi
80 (8)
sp
60 (6)
d
ee
sp
d
ee
sp
gh
Hi
rd it
da
an er lim
t
S p
Up
h
ig
H
gh
e
sp it
gh r lim
i
H pe
Up
80 (8)
ed
pe it
s
h
m
Hig per li
Up
Hi
ed
(0) 0
[Standard]
3-spot blower internal resistance
Square duct blower internal resistance
(1) 10
(2) 20
0 (0)
2-spot blower internal resistance
10 (1)
13
14
Lower
limit
16
18
Air flow (m3/min)
20
Upper
limit
14
Lower
limit
Model FDUMJ112HKXE2
120 (12)
100 (10)
100 (10)
ed
igh
M
rd
da
H
d
r
da
an
40 (4)
rd
20 (2)
0 (0)
ium
20 (2)
ium
ow
L
rd
da
an
ed
St
St
rd
M
da
an
St w
Lo
da
an
St
an
40 (4)
um
gh
St
60 (6)
ow
ow
d
Hi
L
d
ar
ee
d
L
ed
pe t
s
gh mi
Hi w li
Lo
sp
ee
ium
i
ed
ed
rd it
da
an er lim
t
S p
Up
d
M
ed
pe
s
h
it
Hig w lim S
tan
Lo
d
ig
H
d
ee
80 (8)
ee
d
ee
sp
igh
sp
imit
er l
p
p
rdU Hig
nda
hs
Sta
p
sp
gh
dH
ee
ig
sp
gh
gh
Hi
60 (6)
Hi
d
ee
sp imit
h
l
g
Hi per
Up
Hi
80 (8)
22
Upper
limit
Model FDUMJ140HKXE2
120 (12)
ed
spe it
h
g
i
Hi er l m
p
Hi
Up
gh
17
20
Air flow (m3/min)
0 (0)
10 (1)
10 (1)
24
21
Lower
limit
25
28
Air flow (m3/min)
31
Upper
limit
Lower
limit
26
30
34
3
38
Upper
limit
807
FDC-HKX
19.2.8 Noise level
Note (1) The data are based on the following conditions.
Ambient air tempetature: Indoor unit 27C DB, 19C WB. Outdoor unit 35C DB
(2) The data in the chart are measuted in an unechonic room.
(3) The noise levels measured in the field are usually higher than the data because of reflection.
1.5m
Mike (center & low points)
70
N70
60
60
N60
50
50
N50
40
40
N40
30
30
N2
N30
20
63
125
250
500
1000
2000
4000
20
8000
70
70
N70
60
60
N60
50
50
N50
40
40
N40
30
30
N2
N30
20
63
125
250
500
1000
2000
20
8000
4000
70
Models FDTJ28HKXE2,36HKXE2
Models FDTJ45HKXE2,56HKXE2
Model FDTJ71HKXE2
Noise level 37 dB (A) at HIGH
Noise level 38 dB (A) at HIGH
Noise level 40 dB (A) at HIGH
34 dB (A) at MEDIUM
35 dB (A) at MEDIUM
38 dB (A) at MEDIUM
33 dB (A) at LOW
34 dB (A) at LOW
36 dB (A) at LOW
70
70
N70
60
60
N60
50
50
N50
40
40
N40
30
30
N2
N30
20
63
125
250
500
1000
2000
20
8000
4000
70
N70
60
60
N60
50
50
N50
40
40
N40
30
30
N2
N30
20
63
125
250
500
1000
2000
4000
20
8000
70
70
N70
60
60
N60
50
50
N50
40
40
N40
30
30
N2
N30
20
63
125
250
500
1000
2000
4000
20
8000
70
Model FDTJ90HKXE2
Model FDTJ112HKXE2
Model FDTJ140HKXE2
Noise level 42 dB (A) at HIGH
Noise level 49 dB (A) at HIGH
Noise level 50 dB (A) at HIGH
40 dB (A) at MEDIUM
46 dB (A) at MEDIUM
47 dB (A) at MEDIUM
38 dB (A) at LOW
42 dB (A) at LOW
45 dB (A) at LOW
70
70
N70
60
60
N60
50
50
N50
40
40
N40
30
30
N2
20
63
N30
125
250
500
1000
2000
4000
20
8000
Model FDTWJ71HKXE2B
Noise level 41 dB (A) at HIGH
38 dB (A) at MEDIUM
35 dB (A) at LOW
70
70
70
60
60
N60
50
50
N50
40
40
N40
30
30
20
63
125
250
500
60
60
N60
50
50
N50
40
40
N40
30
30
N30
N2
0
1000
2000
4000
808
N70
1.5m
N70
N30
N2
0
20
8000
20
63
125
250
500
1000
2000
4000
20
8000
FDC-HKX
Model FDTWJ90HKXE2B
Model FDTWJ112HKXE2B
Model FDTWJ140HKXE2B
Noise level 41 dB (A) at HIGH
Noise level 44 dB (A) at HIGH
Noise level 45 dB (A) at HIGH
39 dB (A) at MEDIUM
41 dB (A) at MEDIUM
42 dB (A) at MEDIUM
36 dB (A) at LOW
38 dB (A) at LOW
39 dB (A) at LOW
70
70
70
60
N60
50
50
N50
40
40
N40
30
30
N2
125
250
500
50
50
N50
40
40
N40
30
30
1000
2000
20
8000
4000
63
125
250
500
60
60
N60
50
50
N50
40
40
N40
30
30
N30
20
1000
2000
4000
N2
20
8000
N30
20
63
(c)
60
N60
N2
70
N70
60
N30
20
63
60
70
N70
N70
70
125
250
500
1000
2000
4000
20
8000
70
N70
60
60
N60
50
50
N50
40
40
N40
30
30
N2
N30
20
63
125
250
500
1000
2000
4000
20
8000
70
Model FDTSJ22HKXE2B
Noise level 39 dB (A) at MEDIUM
38 dB (A) at LOW
Model FDTSJ71HKXE2B
Noise level 44 dB (A) at HIGH
40 dB (A) at MEDIUM
38 dB (A) at LOW
809
FDC-HKX
(d) Cassetteria type (FDR)
Unit
1.5m
Model FDRJ28HKXE2
Models FDRJ45HKXE2, 56HKXE2
Noise level 43 dB (A) at HIGH
Noise level 44 dB (A) at HIGH
41 dB (A) at MEDIUM
41 dB (A) at MEDIUM
38 dB (A) at LOW
38 dB (A) at LOW
Sound pressure level
(Standard 0.0002 bar) dB
1.5m
810
Model FDRJ22HKXE2
Model FDRJ28HKXE2
Models FDRJ45HKXE2, 56HKXE2
Noise level 41 dB (A) at HIGH
Noise level 42 dB (A) at HIGH
Noise level 43 dB (A) at HIGH
39 dB (A) at MEDIUM
40 dB (A) at MEDIUM
40 dB (A) at MEDIUM
36 dB (A) at LOW
37 dB (A) at LOW
37 dB (A) at LOW
FDC-HKX
(e)
1.5m
Model FDUMJ36HKXE2
Model FDUMJ112HKXE2
Model FDUMJ140HKXE2
Noise level 38 dB (A) at HIGH
Noise level 39 dB (A) at HIGH
35 dB (A) at MEDIUM
37 dB (A) at MEDIUM
32 dB (A) at LOW
34 dB (A) at LOW
811
FDC-HKX
1m
Unit
1m
Model FDEJ71HKXE2B
Model FDEJ112HKXE2B
Noise level 49 dB (A) at HIGH
46 dB (A) at MEDIUM
42 dB (A) at LOW
(f)
Model FDEJ140HKXE2B
Noise level 50 dB (A) at HIGH
47 dB (A) at MEDIUM
42 dB (A) at LOW
50
N50
40
40
N40
30
30
N30
N2
20
63
125
250
500
1000
2000
4000
20
8000
812
Model FDKJ45HKXE2
Noise level 44 dB (A) at HIGH
41 dB (A) at MEDIUM
37 dB (A) at LOW
Sound pressure level
(Standard 0.0002 bar) dB
60
N60
50
Mike
(Center & low points)
70
N70
60
1m
Model FDKJ22HKXE2
Noise level 40 dB (A) at HIGH
37 dB (A) at LOW
70
1m
Unit
FDC-HKX
Model FDKJ56HKXE2
Noise level 46 dB (A) at HIGH
43 dB (A) at MEDIUM
39 dB (A) at LOW
Model FDKJ71HKXE2
Noise level 47 dB (A) at HIGH
44 dB (A) at MEDIUM
40 dB (A) at LOW
Indoor unit
1m
70
60
60
50
50
40
30
63
30
125
250
500
1000
2000
4000
20
8000
Noise level
70
70
60
60
50
50
40
40
30
30
63
125
250
500
1000
2000
4000
20
8000
70
40
Models FDCP280HKXE2B
FDCJ280HKXE2B
Models FDCP224HKXE2B
FDCJ224HKXE2B
Noise level
58 dB (A)
Sound pressure level
(Standard 0.0002 bar) dB
Models FDCP140HKXE2B
FDCJ140HKXE2B
Noise level
56 dB (A)
59 dB (A)
70
70
N70
60
60
N60
50
50
N50
40
40
N40
30
30
N2
N30
20
63
125
250
500
1000
2000
4000
20
8000
813
TB
A
BL
BL
WH
RD
Y/GN
Fan motor
Internal thermostat for FMI
Capacitor for FMI
Drain motor
Float switch (For overflow prevention)
Louver motor
Limit switch
Stepping motor (For Exp.v)
Auxiliary relay (For FMI)
Auxiliary relay (For DM)
Auxiliary relay (For LM)
ThI-A
ThI-R
SW1
SW2
SW3
SW4
SW6
Trl
Val
LEDR
LEDG
Mark
CnO
CnK2
SK
X2
Thermistor
Thermistor
Indoor unit address ten's place
Indoor unit address unit's place
Outdoor unit address ten's place
Outdoor unit address unit's place
Change of heat pume type
Transformer
Varistor
Indication lamp (Red)
Indication lamp (Green)
Parts name
WH
12
X3
CnD
10
X4
CnR
CnI
FS
CnI
WH
J5
J6
J2
X5
X4
X3
X2
X1
J7
J3
X6
220/240V
CnW1
Parts name
Val
Fuse
Connector ( mark)
Terminal block
Terminal (F)
Connector
Operation indication (DC12)
Heating indication (DC12)
ON indication for CM (DC12)
Check indication (DC12)
Distant operation
Spark killer
CnR
DM
F
CnA-Z
TB
mark
mark
XR1
XR2
XR3
XR4
XR5
SK
Mark
SK
CFI
OR
CnF
11
CnF
FMI
(49FI)
13
X6
Y/GN 5 Y/GN
CnJ
LM
CnJ
X5
X1
WH
J4
SW5
SW6
1 2 3
CnB
CnS
CnN
CnH
CnT
CnA
GR
Mark
SW5-3
SW5-2
SW5-1
Color
Red
White
Yellow
Yellow/Green
Mark
Normal
ON
OFF
Run Stop
Reverse Invalid
Input
signal
Function
Remote
controller
RD WH BK
Thc
RD
WH
Y
Y/GN
Thl-R
SM
ON
OFF
ON
Option
Thl-A
X Y Z
BK
BK
BK
LS
XR4
BK
Color
Y
Z
BK
BK
CnS2
XR5
Black
Blue
Brown
Gray
Orange
BK
WH
RD
BK
BK
BK
GR
XR2
RD
Y
BK
XR3
OR
RD
Y
XR1
CnA2
OR
Function of switches
BK
BL
BR
GR
OR
Mark
Color mark
ON
OFF 1 2 3 4
ON
OFF
SW4
Check
Normal
LEDG LEDR
HA
CnZ
CnW2
BL
BL
RD
Checker
17V
8V
RD
CnE
Trl
FMI
49FI
CFI
DM
FS
LM
LS
SM
X1,2,3,6
X4
X5
Y/GN
CnK
WH
RD
Mark
Parts name
F(3.15A)RD
Meaning of marks
Outdoor
unit
(Signal
line)
Power
source
TB
L
WH
RD
OR
OR
OR
WH
WH
WH
BL
RD
BK
BK
BK
RD
BL
WH
WH
OR
BR
BR
BK
BK
WH
GR
RD
RD
814
WH
CnU
FDC-HKX
FMI
49FI
CFI
DM
FS
LM
LS
SM
X1,2,3,6
X4
X5
Mark
BL
BL
F(3.15A)
Fan motor
Internal thermostat for FMI
Capacitor for FMI
Drain motor
Float switch (For overflow prevention)
Louver motor
Limit switch
Stepping motor (For Exp.v)
Auxiliary relay (For FMI)
Auxiliary relay (For DM)
Auxiliary relay (For LM)
Parts name
TB
Y/GN
WH
RD
Y/GN
Y/GN
CnO
CnK2
BL
CnK
BL
WH
RD
CnF2
UH
OR
OR
CnF2
WH
CFI2
CnFC2 OR
FMl2
UH
13
CnF1
X2
10
CnI1
CnFC1 OR
OR
CnF1
OR
14
X6
WH
FMl1
X3
12
11
X1
ThI-A
ThI-R
SW1
SW2
SW3
SW4
SW6
Trl
Val
LEDR
LEDG
Mark
Thermistor
Thermistor
Indoor unit address ten's place
Indoor unit address unit's place
Outdoor unit address ten's place
Outdoor unit address unit's place
Change of heat pume type
Transformer
Varistor
Indication lamp (Red)
Indication lamp (Green)
Parts name
F
CnA-Z
TB
mark
mark
XR1
XR2
XR3
XR4
XR5
SK
Mark
CnD
CnR
Parts name
CnI
SK
CnR
FS DM
CnI
X4
Fuse
Connector ( mark)
Terminal block
Terminal (F)
Connector
Operation indication (DC12)
Heating indication (DC12)
ON indication for CM (DC12)
Check indication (DC12)
Distant operation
Spark killer
RD
CnJ
LM
CnJ
X5
Val
J6
J2
LEDG
J7
J3
SW1
J8
J4
SW4
SW6
ON
OFF 1 2 3 4
SW5
SW3
Check
LEDR
HA
Mark
CnB
CnS
CnN
CnH
CnT
Mark
SW5-3
SW5-2
SW5-1
BK
WH
RD
RD
WH
Y
Y/GN
Mark
Remote
controller
WH
Thc
Color
Red
White
Yellow
Yellow/Green
Option
Reverse Invalid
Normal
OFF
Normal
Test run of condensate pump motor
ON
Run Stop
ON
Input
signal
LS
Z Y X
BK
Function
TB
BK
BK
Thl-R
Thl-A
XR4
XR2
SM
OFF
OFF
ON
BK
RD
XR5
XR3
XR1
28~56H CASES
CnS2
BK
BK
BK
BK
BK
BK
GR
BK
GR
WH
OR
RD
Y
WH
CnA2
OR
RD
Y
Function of switches
Color
Black
Blue
Brown
Gray
Orange
Color mark
BK
BL
BR
GR
OR
CnA
Checker
CnW2
BL
BL
RD
RD
ON
OFF 1 2 3 4
SW2
8V
17V
CNZ
CnE
Normal
X6
Trl
J5
J1
X5
X4
X3
X2
X1
CnW1
WH
220/240V
WH
Meaning of marks
(Signal)
(Power supply)
Outdoor unit
(Signal line)
TB
BK
Power
source
RD
RD
WH
WH
BL
WH
WH
GR
RD
RD
WH
WH
BR
BR
RD
RD
WH
WH
OR
OR
WH
WH
CnU
FDC-HKX
815
*1
FMI1,2
49FI
CFI1,2
DM
FS
LM
LS
SM
X1,2,3
X4
X5
RD
RD
CnF2
OR
Y/GN
WH
CnW4
RD
RD
CnM
CnB2
CnK2
BL
CnK
BL
CnW3
BL
BL
RD
CnW2
CnO
Y/GN
BL
BL
CnW4
BL
17V
BL
RD
8V
RD
WH
WH
RD
RD
Trl
WH
WH
220/240V
RD
CnL
RD
*1
Val
RD
L
H
OR
X1
CnF3
X2
CnD
CFl2
UH
BR
OR
CnF3
FMl2
(49FI)
Parts name
ThI-A
ThI-R
SW1
SW2
SW3
SW4
SW6
Trl
Val
LEDR
LEDG
Mark
Thermistor
Thermistor
Indoor unit address ten's place
Indoor unit address unit's place
Outdoor unit address ten's place
Outdoor unit address unit's place
Change of heat pume type
Transformer
Varistor
Indication lamp (Red)
Indication lamp (Green)
Parts name
CFI1
UH
BR
OR
CnF2
FMI1
(49FI)
Fan motor
Internal thermostat for FMI
Capacitor for FMI
Drain motor
Float switch
Louver motor
Limit switch
Stepping motor (For Exp.v)
Auxiliary relay (For FMI)
Auxiliary relay (For DM)
Auxiliary relay (For LM)
Meaning of marks
Mark
BL
BL
Y/GN
F(3.15A)
BR
RD
CnF2
CFI1
UH
BR
OR
OR
X3
CnF2
Cn Cn
F6 F5
FMl1
(49FI)
X3
X2
X1
CnI
FS
SK
CnI
X5
X4
F
CnA-Z
TB
mark
mark
XR1
XR2
XR3
XR4
XR5
SK
Mark
Fuse
Connector ( mark)
Terminal block
Terminal (F)
Connector
Operation indication (DC12)
Heating indication (DC12)
ON indication for CM (DC12)
Check indication (DC12)
Distant operation
Spark killer
Parts name
Notes (1) FDTSJ22HKXE2B is different from others as indicated with *1 in the diagram below.
TB
A
RD
RD
BL
BL
BL
BK
BK
Outdoor unit
(Signal line)
RD
N Y/GN
TB
BL
BL
RD
RD
Power
source
RD
Y/GN
BK
BK
BL
BL
BL
RD
WH
WH
WH
WH
Y/GN
Y/GN
BK
BR
BR
BK
BK
BK
GR
RD
WH
Y/GN
Y/GN
WH
WH
CnR
X5
CnJS
CnJS
LM
SK
CnR
X4
DM
WH
WH
RD
WH
BR
BR
WH
RD
RD
OR
OR
OR
WH
WH
816
WH
CnU
HA
CNZ
J5
J1
J6
J2
J7
J3
SW6
J4
ON 1 2 3 4
OFF
SW5
SW3 SW4
ON 1 2
3
OFF
SW2
BK
RD
WH
Mark
SW5-3
SW5-2
SW5-1
Color
Red
White
Yellow
Yellow/Green
Normal
ON
OFF
Run Stop
Reverse Invalid
Input
signal
ON
OFF
ON
Mark
Remote
controller
RD WH BK
Thc
X Y Z
Option
SM
RD
WH
Y
Y/GN
Y
Z
TB
LS
Thl-R
Thl-A
XR4
XR2
Function
CnB2
BK
RD
WH
BK
BK
BL
BK
RD
BL
CnJS
CnN2
BK
BK
CnH2
BK
XR5
BL
BK
BK
XR3
XR1
OR
RD
Y
BK
GR
CnA2
Color
Black
Blue
Brown
Gray
Orange
CnB
CnS
CnN
CnH
CnT
OR
RD
Y
BK
GR
Function of switches
BK
BL
BR
GR
OR
Mark
Color mark
SW1
Normal Check
LEDG LEDR
Checker
CnE
CnA
FDC-HKX
BL
BL
WH
Y/GN
CnS
Y/GN
F(3.15A)
CnO
CnK2
BL
CnK
BL
WH
RD
X1
CnF4
X2
Val
OR
OR
WH
Y/GN
CnD
CFl1
UH
CnF4
CnF2
CnF4
FMI1
(49FI)
X3
BL
X3
X2
X1
CnF2
CnF5
OR
OR
CnF5
FMI2
(49FI)
BK
X4
Parts name
Fan motor
Capacitor for FMI
Drain motor
Float switch
Stepping motor (For Exp.v)
Auxiliary relay (For FMI)
Auxiliary relay (For DM)
Internal thermostat for FMI
Thermistor
Mark
FMI1,2
CFI1,2
DM
FS
SM
X1,2,3
X4
49FI
ThI-A
ThI-R
SW1
SW2
SW3
SW4
SW6
Trl
Val
LEDR
LEDG
F
Mark
Thermistor
Indoor unit address ten's place
Indoor unit address unit's place
Outdoor unit address ten's place
Outdoor unit address unit's place
Change of heat pume type
Transformer
Varistor
Indication lamp (Red)
Indication lamp (Green)
Fuse
Parts name
CnA-Z
TB
mark
mark
XR1
XR2
XR3
XR4
XR5
SK
Mark
SK
DM
CnRI
CnI
FS
CnI
CnRI
Parts name
CnRI
CnR
CnR
CnRI
X4
Connector ( mark)
Terminal block
Terminal (F)
Connector
Operation indication (DC12)
Heating indication (DC12)
ON indication for CM (DC12)
Check indication (DC12)
Distant operation
Spark killer
CnF3
CFI2
UH
CnF5
CnF3
TB
Meaning of marks
Outdoor
unit
(Signal line)
Power
source
RD
Y/GN
BL
TB
L
BL
RD
Y/GN
BK
BK
BK
BK
RD
BL
BL
RD
RD
BR
BR
WH
WH
RD
RD
BL
Y/GN
Y/GN
BL
RD
WH
WH
BL
BK
BK
BK
BR
BR
BR
WH
BR BR
BK
RD
RD
BK
WH
WH
WH
GR
RD
RD
RD
RD
WH
RD
SW6
1 2 3
SW5
J5
J3
J6
J4
OR
RD
Y
BK
GR
BK
Color
Black
Blue
Brown
Gray
Orange
Remote
controller
RD WH BK
Thc
X Y Z
CnA2
TB
BK
Mark
SW5-3
SW5-2
SW5-1
Normal
ON
OFF
Run Stop
Reverse Invalid
Color
Red
White
Yellow
Yellow/Green
Input
signal
Function
Mark
RD
WH
Y
Y/GN
SM
ThI-R
ON
OFF
ON
Option
ThI-A
XR4
XR2
Function of switches
Mark
BK
BL
BR
GR
OR
BK
BK
CnN3
BK
BK
CnN2
XR3
XR1
XR5
CnH2
CnB
BK
WH
RD
OR
RD
Y
BK
GR
RD
RD
BK
BK
Color mark
J7
ON 1 2 3 4
OFF
ON
OFF
CnN
SW3 SW4
Check
Normal
SW2
LEDR
LEDG
SW1
HA
CnZ
CnH
CnW2
BL
17V
BL
RD
8V
Checker
TrI
CnE
CnW1
WH
200/240V
WH
CnT
CnA
CnU
FDC-HKX
817
FMI1,2
CFI1,2
DM
FS
SM
X1,2,3
X4
49FI
ThI-A
Parts name
Fan motor
Capacitor for FMI
Drain motor
Float switch (For overflow prevention)
Stepping motor (For Exp.v)
Auxiliary relay (For FMI)
Auxiliary relay (For DM)
Internal thermostat for FMI
Thermistor
Meaning of marks
Mark
Y/GN
BL
CnM
CnO
CnK2
BL
CnK
BL
TB
A BL
RD
WH
Y/GN
F(3.15A)
WH
TB
L RD
2
X1
CnF4
X2
Val
Y/GN
WH
CnF4
OR
OR
CFI1
UH
ThI-R
SW1
SW2
SW3
SW4
SW6
Trl
Val
LED R
LED G
F
Mark
Thermistor
Indoor unit address ten's place
Indoor unit address unit's place
Outdoor unit address ten's place
Outdoor unit address unit's place
Change of heat pume type
Transformer
Varistor
Indication lamp (Red)
Indication lamp (Green)
Fuse
Parts name
X1
X2
BL
BK
CnF2
CnA-Z
TB
mark
mark
XR1
XR2
XR3
XR4
XR5
SK
Mark
X3
X4
OR
OR
CnF5
FMI2
(49FI)
CnF5
CnD
CnF4
CnF2
FMI1
(49FI)
X3
BL
Outdoor
unit
(Signal line)
Power
source
RD
RD
WH
BK
BK
BK
BR
BR
BK
BL
BL
BL
RD
RD
RD
Y/GN
Y/GN
WH
RD
RD
BL
BL
BL
Y/GN
WH
WH
WH
Y/GN
BK
BK
BK
BR
BR
BR
CnF3
CFI2
UH
CnF5
*1
SK
CnF3
Parts name
CnG
CnRI
CnR
DM
CnR
CnRI
X4
9
Connector ( mark)
Terminal block
Terminal (F)
Connector
Operation indication (DC12)
Heating indication (DC12)
ON indication for CM (DC12)
Check indication (DC12)
Distant operation
Spark killer
WH
BR
BR
BK
RD
RD
BK
WH
WH
WH
GR
RD
RD
RD
RD
818
WH
CnU
CnRI
CnI
FS
CnI
CnRI
Check
Normal
J5
J3
J6
J4
SW6
ON
OFF 1 2 3 4
SW5
ON
OFF 1 2 3
CnN
CnA
BK
CnB
BK
TB
WH
RD
OR
RD
Y
BK
GR
Mark
BK
BK
OR
RD
Y
BK
GR
Black
Blue
Brown
Gray
Orange
Color
Remote
controller
RD WH BK
Thc
X Y Z
CnA3
OR
RD
Y
BK
GR
SW5-3
SW5-2
SW5-1
Mark
Color
Red
White
Yellow
Yellow/Green
Mark
RD
WH
Y
Y/GN
Normal
ON
OFF
Run Stop
Reverse Invalid
Input
signal
Function
SM
Thl-R
Thl-A
Option
ON
OFF
ON
Function of switches
BK
BL
BR
GR
OR
BK
BK
BK
BK
CnH2
CnN2 CnN3
RD/BK
RD/BK
CnA2
RD
RD
BK
XR1
XR2
XR3
XR4
XR5
Color mark
J7
CnT
CnH
LEDR
HA
LEDG
CnZ
Checker
CnE
BL
17V
8V
RD
CnW2
Trl
CnW1
WH
220/240V
WH
FDC-HKX
FMI1,2
CFI1,2
49FI
LM
LS
SM
X1,2,3
X5
ThI-A
Mark
WH
RD
WH
Y/GN
RD
BL
BL
CnM
BL
BL
RD
RD
CnO
CnK2
BL
CnK
BL
CnW3
Y/GN
CnK2
CnW4
BL
17V
BL
CnW2
WH
RD
VaI
*1
X3
X2
X1
OR
OR
H60
CnF3
FMI2
(49FI)
X5
X4
BR
Y/GN
CnD
CFI2
H50
CnF3
X2
X1
OR
OR
CnF2
FMI1
(49FI)
Cn
F6
X3
CFI1
UH
Fan motor
Capacitor for FMI
Internal thermostat for FMI
Louver motor
Limit switch
Stepping motor (For Exp.v)
Auxiliary relay (For FMI)
Auxiliary relay (For LM)
Thermistor
ThI-R
SW1
SW2
SW3
SW4
SW6
Trl
Val
LEDR
LEDG
F
Mark
Thermistor
Indoor unit address ten's place
Indoor unit address unit's place
Outdoor unit address ten's place
Outdoor unit address unit's place
Change of heat pume type
Transformer
Varistor
Indication lamp (Red)
Indication lamp (Green)
Fuse
Parts name
CnA-Z
TB
mark
mark
XR1
XR2
XR3
XR4
XR5
SK
Mark
CnF2
Cn
F5
Connector ( mark)
Terminal block
Terminal (F)
Connector
Operation indication (DC12)
Heating indication (DC12)
ON indication for CM (DC12)
Check indication (DC12)
Distant operation
Spark killer
Parts name
Parts name
BL
BL
CnW4
WH
200/240V
8V
RD
RD
CnL
WH
RD
Tr1 RD
RD
Y/GN
F(3.15A)
WH
Meaning of marks
Outdoor unit
(Signal line)
TB
RD
BL
BK
TB
RD
RD
Power
source
RD
WH
BK
BK
RD
WH
RD
Y/GN
Y/
GN
WH
WH
BL
BL
BK
BR
BR
SK
OR
OR
X5
CnJS
CnJS
LM
OR
WH
WH
WH
WH
J5
J1
Mark
J4
Color
Black
Blue
Brown
Gray
Orange
J7
J3
Mark
SW5-3
SW5-2
SW5-1
Mark
CnB2
BK
RD
WH
Y
Y/GN
BK
WH
RD
RD
WH
BK
BL
Normal
Remote
controller
ON
OFF
Run Stop
X Y Z
RD WH BK
Thc
Color
Red
White
Yellow
Yellow/Green
Reverse Invalid
TB
SM
LS
ThI-R
ThI-A
XR4
XR2
Input
signal
BK
BK
CnN2
BK
CnH2
BK
XR5
XR3
XR1
GR
CnS CnS2
BL
RD
RD
BK
BK
GR
ON
OFF
ON
Y
BK
RD
BK
OR
RD
OR
Function
CnB
CnN
CnH
CnT
Function of switches
BK
BL
BR
GR
OR
J6
J2
SW6
ON
OFF 1 2 3 4
ON
OFF 1 2 3
SW5
Normal Check
LEDG LEDR
HA
CnZ
Color mark
Checker
CnE
CnA
(f)
Option
CnU
FDC-HKX
819
FMI
CFI
49FI
LM
LS
SM
X1,2,3
X5
ThI-A
Mark
Y/GN
ThI-R
SW1
SW2
SW3
SW4
SW6
Trl
Val
LEDR
LEDG
F
Mark
VaI
CnF1
Y/GN
X2
X1
Parts name
Thermistor
Indoor unit address ten's place
Indoor unit address unit's place
Outdoor unit address ten's place
Outdoor unit address unit's place
Change of heat pume type
Transformer
Varistor
Indication lamp (Red)
Indication lamp (Green)
Fuse
CnO
CnK2
Y/GN
CnK
BL
WH
RD
BL
F(3.15A)
BL
BL
WH
Parts name
TB
A
Fan motor
Capacitor for FMI
Internal thermostat for FMI
Louver motor
Limit switch
Stepping motor (For Exp.v)
Auxiliary relay (For FMI)
Auxiliary relay (For LM)
Thermistor
Meaning of marks
Outdoor unit
(Signal line)
RD
RD
OR
OR
CFI
X3
X2
X1
CnA-Z
TB
mark
mark
XR1
XR2
XR3
XR4
XR5
SK
Mark
OR
OR
CnF1
X3
CnF2
CnF1
FMI
(49FI)
RD
Power
source
WH
BL
BL
TB
L
BK
BK
RD
WH
WH
WH
GR
SK
LM
Parts name
CnJ
CnJ
X5
Connector ( mark)
Terminal block
Terminal (F)
Connector
Operation indication (DC12)
Heating indication (DC12)
ON indication for CM (DC12)
Check indication (DC12)
Distant operation
Spark killer
CnD
X5
OR
OR
OR
WH
WH
WH
820
J5
LEDR
LEDG
Check
HA
CnZ
Normal
J3
J6
J4
J7
SW6
1 2 3 4
CnB
CnN
CnH
CnT
OR
Mark
SW5-3
SW5-2
SW5-1
Color
Red
White
Yellow
Yellow/Green
Normal
ON
OFF
Run Stop
Reverse Invalid
Input
signal
ON
OFF
ON
Mark
RD
WH
Y
Y/GN
Function
Remote
controller
RD WH BK
Thc
Color
Black
Blue
Gray
Orange
BK
WH
SM
LS
ThI-R
ThI-A
XR4
XR2
X Y Z
BK
BL
TB
RD
X
BK
CnS2
BL
BK
CnN2
BK
XR5
XR3
XR1
CnS
RD
RD
BK
BK
GR
BK
RD
Function of switches
BK
BL
GR
OR
Mark
Color mark
ON
OFF
ON 1 2 3
OFF
SW5
CnA
CnW2
BL
BL
RD
RD
Checker
17V
8V
CnE
TrI
CnW1
WH
220/
240V
WH
Option
CnU
FDC-HKX
TB
A
BL
BL
Y/GN
WH
CnF1
Parts name
Fan motor
Capacitor for FMI
Internal thermostat for FMI
Stepping motor (For Exp.v)
Auxiliary relay (For FMI)
Thermistor
Thermistor
Indoor unit address ten's place
Indoor unit address unit's place
Mark
WH
CnF2
CnF1
FMI1
(49FI)
BL
BL
FMI
CFI
49FI
SM
X1,2,3
ThI-A
ThI-R
SW1
SW2
Meaning of marks
Y/GN
BK
BK
RD
Y/GN
F (3.15)
Y/GN
RD
CnK2
BL
CnK
BL
WH
RD
Val
Y/GN
CnS
X2
X1
Y/GN
WH
BK
BK
CnF
H
CnD
CnF
FMI
(49FI)
X3
WH
CFI
X3
X2
X1
OR
OR
CFI
Mark
SW3
SW4
SW6
Trl
Val
LEDR
LEDG
F
Parts name
Outdoor unit address ten's place
Outdoor unit address unit's place
Change of heat pume type
Transformer
Varistor
Indication lamp (Red)
Indication lamp (Green)
Fuse
Mark
CnA-Z
TB
mark
mark
XR1
XR2
XR3
XR4
XR5
Connector ( mark)
Terminal block
Terminal (F)
Connector
Operation indication (DC12)
Heating indication (DC12)
ON indication for CM (DC12)
Check indication (DC12)
Distant operation
Parts name
J5
Trl
J3
J6
J4
J7
SW6
1 2 3 4
SW5
1 2 3
CnB
CnN
CnH
CnT
CnA
Mark
RD
RD
BK
BK
GR
Black
Blue
Gray
Orange
XR4
TB
Mark
SW5-3
SW5-2
SW5-1
X Y Z
RD
WH
Y
Y/GN
Mark
Remote
controller
RD WH BK
Thc
Normal
ON
OFF
Run Stop
Color
Red
White
Yellow
Yellow/Green
Reverse Invalid
Input
signal
ON
OFF
ON
SM
Function
Thl-R
Thl-A
Color
BK
WH
RD
BK
CnN
BK
BK
CnH2
BK
XR5
XR3
XR2
BK
XR1
Y
BK
GR
Function of switches
BK
BL
GR
OR
OR
RD
CnA2
RD
OR
Color mark
ON
OFF
ON
OFF
Check
Normal
HA
Checker
CnW2
17V
8V
LEDR
BL
BL
RD
RD
LEDG
CnZ
CnE
CnW1
WH
220/
240V
WH
WH WH
RD
Outdoor
unit
(Signal line)
RD
RD/Y
RD
Power
source
BL
BL
BL
RD
TB
L
BK
BK
BK
RD
GR
WH
(i)
Option
WH
FDC-HKX
821
Y/GN
Y/GN
SA
CM
FMo
49Fo
52C
CH
CFo
X1
X4
X5
X10~12
52C
CT
Compressor motor
Fan motor (outdoor unit)
Internal thermostat for FMo
Magnetic contactor for CM
Crankcase heater
Capacitor for FMo
Ausiliary relay (for 52C)
Ausiliary relay (for 20S)
Ausiliary relay (for SV1)
Ausiliary relay (for FMo)
CM
Inverter P.W.B
Noise filter
20S
SV1
63H1
63H2
Tho-A
Tho-D
Tho-R
Tho-C
CT
SA
Mark
F(3.15A)
52C
22
CnA1
8V
Parts name
WH
CnX2
Tr
Va1~3
TB1~2
F
SW1
SW2
LED1
LED2
mark
mark
Mark
13
CnM1
Parts name
LED1
20S
X4
X4
52C
X1
X1
Digital display
Transformer
Varistor
Terminal block ( mark)
Fuse
Indoor unit address ten's place
Indoor unit address unit's place
Indication lamp (Red)
Indication lamp (Green)
Terminal (F)
Connector
CnE
1 2 3 4 5 6 7 8
SW3
CFo
CnM1
CnM1
OFF
ON
OR
FMo
(49Fo)
CnY
Signal line
(Indoor unit)
14
15
X12
X11
X10
SW1 SW2
TB2 A B
CnH
CnI1
27
RD 1
200V/17V
Tr
CnA2
BK
X12
X11
X10
CnJ1
CH
CnJ2
21
SV1
J1~J6
BK
BL
OR
RD
Mark
25
Color
CnG
Black
Blue
Orange
Red
Color mark
LED2
X5
X5
24
CnS2
CnS1
CnU
CnD
CnC1
BK
CnB
BK
BK
Tho-C
Tho-A
Tho-D
Tho-R
63H2
WH
Y
GR
Y/GN
Mark
BK
BK
BK
BK
BK
BK
CnQ
BK
CnP 63H1
RD
BK
White
Yellow
Gray
Yellow/Green
Color
RD
CnQ
BK
CnP
Mark
BK
BL
Parts name
Meaning of marks
L3
WH
RD
RD
L2
BL
BL
RD
GR
GR
WH
Power
source
WH
WH
BL
BL
RD
BK
RD
RD
TB1
L1
BK
Y
Y
WH
BK
Y/GR
WH
WH
BK
BK
RD
822
RD
Power source
3Phase
380/415V 50Hz
FDC-HKX
Y/GN
Y/GN
Y/GN
CM
FMo1,2
49F01,2
52C
CH1,2
CF01,2
X1,2
X3,4
X5,6
X10~12
X13
Mark
CT1
CM1
Inverter P.W.B
Compressor motor
Fan motor (outdoor unit)
Internal thermostat for FMo
Magnetic contactor for CM
Crankcase heater
Capacitor for FMo
Ausiliary relay (for 52C1,52C2)
Ausiliary relay (for 20S)
Ausiliary relay (for SV1,SV2)
Ausiliary relay (for FMo1)
Ausiliary relay (for FMo2)
BK
BL
52C1
Noise filter
RD
Parts name
SA
Meaning of marks
L3
RD
RD
WH
WH
52C2
CT2
BL
20S
SV1,2
63H1-1,1-2
63H2
Tho-A
Tho-C
Tho-D1,D2
Tho-R
CT1,2
SA
Tr
Mark
BL
CM2
BL
GR
CnJ1
CH1
CnJ1
21
52C1
22
52C2
22
CnJ2
CH2
CnJ2
21
Parts name
WH
RD
200V/17V
CnA2
Tr 8V
CnA1
BK
GR
WK
WH
RD
GR
GR
L2
BL
Power
source
BL
WH
BL
14
13
X12
X11
X12
M
Y
CnX2
Va1~4
TB1,2
F
SW1
SW2
LED1
LED2
mark
mark
Mark
SW3
CnM2
Parts name
CnE
52C1
X1
X1
CFO2
CnM2
CnM2
OR
FMO2
(49FO2)
CnM2
16
Varistor
Terminal block ( mark)
Fuse
Indoor unit address ten's place
Indoor unit address unit's place
Indication lamp (Red)
Indication lamp (Green)
Terminal (F)
Connector
Signal line
(Indoor unit)
X13
X13
OFF 1 2 3 4 5 6 7 8
CnY
SW1 SW2
ON
CnM1
CFO1
CnM1
CnM1
OR
FMO1
(49FO1)
15
X10
X10
TB2 A B
CnH
CnI1
27
X11
BL
F(3.15A)
BK
WH
RD
RD
RD
RD
BK
BK
Y/GN
BL
WH
WH
BK
WH
WH
TB1
L1
BK
Y/GN
Y/GN
OR
OR
X2
52C2
X2
Digital display
X4
X5
LED2
SV1
X5
BK
BL
GR
OR
RD
Mark
X6
CnG
Color
J1~J6
10
SV2
X6
Black
Blue
Gray
Orange
Red
Color mark
LED1
20S
X4
RD
RD
P
P
Y
Y
BK
BK
RD
RD
Power source
3Phase
380/415V 50Hz
25
24
BL
BK
BK
BK
BK
BK
BK
WH
Y
Y/GN
P
BK
BK
BK
RD
CnQ
Color
White
Yellow
Yellow/Green
Pink
Tho-C
Tho-A
Tho-D2(CM2)
Tho-D1(CM1)
Tho-R
63H2
BK
Mark
CnS2
BK
CnS1
CnU
CnD
CnC2
CnC1
BK
CnB
BK
BK
CnQ
RD
BK
FDC-HKX
823
FDC-HKX
19.4 OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER
(1)
Panel shown below will appear if you open the cover. All contents of display on the LCD are indicated simultaneously for the purpose of explanation.
Pull the knob on the cover to this side to open it downward.
Filter sign
Remote display
Heating
preparation display
Operation/
Inspection indicator lamp
During operation: Green lamp flashes.
In case of error: Red lamp flashes.
Central display
This is displayed when the unit is
controlled with the optional central console.
On/Off switch
Timer operation display
Contents of timer operation are displayed.
(Also displayed when the air conditioner
is stopped.)
CENTER REMOTE F I L T E R
PROGRAM TIMER
FILTER AUTO LIFT
ON
Setting
temperature display
DRYCOOLFANHOT KEEP
SET TEMP
Outdoor No.
Return air
temperature display
TIMER
CHECK
SET
TEMP
T I M E
FAN
Hi
Mi
Lo
OFF
A M
P M
F A N
SPEED
AUTO
SWING
Note
Indicated value may be different
from actual reading on a thermometer
or other instrument but this is
notnecessarily an error.
Mode switch
Cover
Inspection switch
Use this switch when servicing the unit.
Timer switch
Set switch
Temperature/
Time setting switch
824
FDC-HKX
(2) Operations of major functional items under each operation mode
Operation mode
Cooling
Functional item
Heating
Fan
Thermostat ON Thermostat OFF Complete stop Thermostat ON Thermostat OFF
Remote controller Remote controller Remote controller Remote controller Intermittent operacommand
command
command
command
tion (3)
Selected frequency
adaptation
Fully closed
Fully closed
frequency
Fully opened Selected
adaptation
/
Fully closed
Compressor 2
(Without inverter)
4-way valve
Selected frequency(4)
adaptation
Dehumidifying
Defrosting
Model (Indoor)
Category
All series
22 model 28 model 36 model 45 model 56 model 71 model 90 model 112 model 140 model
10 ~ 15
10 ~ 20
10 ~ 25
10 ~ 25
15 ~ 30
15 ~ 40
15 ~ 50
35 ~ 60
35 ~ 70
5 ~ 15
5 ~ 20
5 ~ 25
5~ 25
5 ~ 30
5 ~ 40
5 ~ 50
5 ~ 60
5 ~ 70
Capacity
Item
Compressors total operation frequency (Hz)
140 model
224 model
280 model
20 ~ 80
20 ~ 120
20 ~ 130
Model
Fk (Hz) condition
CM1 (Inverter)
CM (Without inverter)
FDCJ224HKXE2B
Fk < 70Hz
25 ~ 90Hz
OFF
FDCP224HKXE2B
Fk 70Hz
40 ~ 100Hz
ON
FDCJ280HKXE2B
Fk < 80Hz
25 ~ 95Hz
OFF
FDCP280HKXE2B
Fk 80Hz
40 ~ 100Hz
ON
Note (1) In case when CM1 only changes from ON to the CM2 ON range, CM1 is reduced at 40 Hz and then CM2 is turned ON.
825
FDC-HKX
(4)
Low -2c
A
+2c High
Room temperature
setting point
4 min.
Temperature check
(5)
22 model
28 model
36 model
45 model
56 model
71 model
90 model
112 model
140 model
Compressor
Indoor unit electronic expansion valve
Indoor unit fan
Outdoor unit fan
Operation block
This cooling operation is mainly for dehumidifying, with which the compressor, indoor and outdoor fans are operated in the patterns as listed
in the following table and in accordance with operation blocks switched with the room temperature sensor. The operation blocks are selected
by checking the return air temperature at 4-minute intervals. Respective functional items are operated in each operation block as shown by the
following table.
Operation block
A
B
C
D
Item
10
15
20
20
25
30
40
50
60
10
10
0
10
10
0
15
10
0
15
10
0
15
15
0
20
15
0
25
15
0
40
35
0
45
35
0
Sum of frequencies on combined indoor units
Frequency adaptation
Hi
Lo
Lo
LoOFF
Operationt
Operationt
Operationt
Stop
Temperature check
Heating operation
(a) Heating
This is same as the cooling operation.
(b) Heating operation with thermostat OFF
1) Intermittent fan operation control
a) When the jumper wire J3 on the indoor PCB is shorted (installed at shipping),the fan of the unit of which the thermostat is
turned OFF during heating is operated in the Lo mode, and the indoor fan is turned OFF if the temperature rises 1C or more
than the return air temperature at the thermostat OFF.
b) Indoor fan OFF condition is maintained for 5 minutes and then the operation is reset at the Lo mode again. After operating for
2 minutes in the Lo mode, return air temperature is checked and, if it is 1C or higher, the indoor fan is turned OFF or, if it is
not higher than 1C, the Lo mode operation continues.
Notes (1) If the heating thermostat has been turned OFF, the temperature is indicated on the remote controller only when the indoor fan is operated in the Lo mode.
When it is OFF, the room temperature at the end of Lo operation is indicated.
(2) If the operation is changed to the defrosting mode while the heating thermostat is at OFF or the thermostat is turned OFF during defrosting, the indoor
fan is turned OFF.
(3) Residual operation of heater is dominant over this control.
826
Notes(1) When the hot start (the compressor is operating and the indoor unit fan is not operating at the setting
blow rate) is going on, the heating preparation is displayed (LCD on the remote controller).
(2) When the required frequency is other than 0 Hz, once the blower should start, it will not stop even
if the temperature drops below 20C.
(3) After the blower has been turned OFF for 7 minutes, the blower is operated regardless of the heat
exchanger temperature. (For 7 minutes after completion of defrosting during defrosting operation)
FDC-HKX
(d) Defrosting
(i) Conditions for starting defrosting
When all the following conditions are met, the defrosting operation will start:
1) The cumulative operating time of the compressor comes up to 48 minutes after completion of a defrosting operation, or it
comes up to 33 minutes after a heating operation starts (the remote controller is turned on).
2) Eight minutes has passed after the compressor was turned off and on.
3) Eight minutes has passed after end of outdoor unit fan motor control.
4) After all the above conditions have been met, the temperature of the heat exchanger thermistor (ThO-R) has been below the
defrosting start temperature for three minutes in succession.
R407C
ire
rw
mpe
f ju
t of
(Cu
fr
f de
p. o
em
on t
ng
osti
J5)
iati
Init
Defrosting start
Heating
Frequency
Heating
Finishing of
defrosting
(ii)
Defrosting
Finishing of
defrosting, start
of defrosting
20sec
Designated Hz
100Hz
Designated Hz
40Hz
65Hz
10sec
CM2 OFF
ON
OFF
ON
CM2 ON
35Hz
ON or OFF
3min.
ON
or
OFF
OFF
ON
ON
OFF
4-way
valve
ON
5sec
SV1.2
ON
OFF
Opener or Closed
Opener
or
Closed
Heating Output
(CnT-3)
On
or
OFF
Heating
Defrosting operation
Heating
827
FDC-HKX
(e) Compressor operation frequency UP control
1) If any indoor unit demands the maximum frequency for more than 3 minutes continuously during heating operation (provided either one of the following conditions is met), the compressor operation frequency will be increased by 5 Hz. Further
increase of 5 Hz will repeat at each time when the maximum frequency is maintained for 3 minutes. However, the frequency
will not rise beyond the upper limit of 30 Hz.
When there are more than one units of indoor blower of which the thermostats are turned OFF or which are blowing.
When one or more units have stopped heating.
When the outdoor temperature is below 0C.
2) This control is released when the required frequency becomes lower than the maximum frequency.
3) When the protective function that suppresses the frequency is actuated during the control, the protective motion takes place
based on the condition in which the frequency has been raised.
(6)
(7)
(8)
At the start of inverter compressor (CM1), the following operations take place regardless of selected frequency.
(a) 5 ~ 25 Hz operation
It is operated in the range of 5 ~ 25 Hz. In this operation, however, the compressor cannot be operated with the current safe or
high pressure controls or discharge pipe control.
(b) 25 ~ 65 Hz operation (only for 224, 280 models)
Maximum frequency is determined based on the temperature detected with the outdoor air temperature sensor (Tho-A).
1) Below 0C : Maximum frequency is 90 Hz. Operation takes place at 90 Hz for 45 seconds after the start.
2) Above 0C : Maximum frequency is 65 Hz. Operation takes place at 65 Hz for 32.5 seconds after the start.
However, if conditions to start the current safe or high pressure controls or discharge pipe temperature control are met in the mean
time, this control is terminated and substituted with the current safe or high pressure controls or discharge pipe temperature control
which determines the compressor frequency. When the latter control is released, the operation returns to the normal mode.
Equipment related to unit protection and maintenance
(9)
(a)
Functions of switches
Switch
Function
All indoor units on the connection are operated.
ON
Indoor unit demands the maximum frequency and the outdoor unit is operated at the maximum frequency ((a) 2) according to the demand from the indoor unit.
SW3-5
OFF Normal operation
ON SW3-5ON : Cooling operation
SW3-6
OFF SW3-5 ON : Heating operation
Note (1) This operation is dominant over other options such as the center console, etc. Operation status is transmitted to the optional equipment.
828
FDC-HKX
(b)
46C
Tc
6C
0C
40C
Tho-A
829
FDC-HKX
[Hz]
To target frequency
5 Hz/min.
Hour [Hz]
5 Hz/2-min.
Note (1) If operation is stopped within 20 minutes, second and later starts are subject to this control.
(d)
Retention
Indoor
expansion valve
Addition of 5 Hz portion
SV1 close
Under-dome
temperature (C)
(e)
Under-dome
temperature (C)
Outdoor fan ON
FDCJ type 2.06(21)
FDCP type 2.26(23)
2.50(25.5)
2.79(28.5)
(f)
2.50(25.5)
2.79(28.5)
Retention
Addition of 5 Hz portion
Reset
80 (100)C
115C
Discharge pipe temperature ( Tho-D1~D2 )
Note (1) ( ) indicates Tho-D2.
830
FDC-HKX
(ii)
Compressor control
Retention
Reset
115C
120C
130C
If the discharge pipe temperature (Tho-D1~D2 detection) occurs twice within 60 minutes or the condition higher than 130C has
continued for 60 minutes including the duration of time of compressor stop, the unit operation is stopped with the error stop.
Note (1) Unless the temperature of 90C or under is maintained for 45 minutes after the discharge pipe error, the unit cannot be started again. (Reset the
power supply to clear.)
(g)
If the incident current value (T phase of converter entrance) at the inverter entrance exceeds the setting value, the frequency
is reduced in the unit of 5 Hz so as to control the operation current.
(ii)
If the required frequency becomes lower than the current safe frequency under this control, the latter frequency dominates
the operation.
(iii) If the frequency is maintained continuously below the reset value for 3 minutes, the operation enters the frequency release mode.
If it fails to reduce the frequency for 6 minutes continuously, this control is released and the operation returns to the normal mode.
(h)
(i)
(j)
(k)
831
FDC-HKX
(l)
Non-inverter compressor (CM2) overcurrent protection (Only for 224, 280 models)
If the T phase current at the secondary side of 52C2 is detected exceeding the setting value for approx. 0.5 second, the
compressor stops. The compressor is reset automatically after a 3-minute delay. If the error is detected at second time within
40 minutes after the initial detection, the unit stops with the error stop.
(o)
When CM1 is on (>= 20Hz) and there is L3-phase current of 0.5 A or less for 10 continuous seconds, it is determined to
be a phase fault and CM1 and CM2 are set to off.
(ii)
If this is detected 5 times within 60 minutes of the first detection, an error stop is performed. If (i) is detected when CM1
is on within 10 minutes of the power being turned on, an error stop is performed on the first detection.
(iii) If the CM2 L3-phase current is 2 A or less for 5 continuous sections after CM2 has gone on, it is determined to be a
phase fault and an error stop is performed.
(p)
(q)
140 model
10 units
16 units
Note (1) They are the numbers of units used for judgement of error for the purpose of control and not
equal to the numbers of units which can be connected.
Heating
capacity
-1
+1
Heating
capacity
832
High
Heating
capacity
Low
Low
+2
Thermostat setting temperature
With SW5-2 "ON"
+4
Heating
capacity
FDC-HKX
(11)
(a) This control starts 1 minute after starting compressor during cooling or dehumidifying operation, controls the outdoor fan at the
outdoor temperature (Tho-A) being below 22C and enables the cooling operation.
Disabled
Control A
For 140 : OFF, 1 ~ 2 speed control ranges
For 224, 280 : OFF, 1 ~ 3 speed control ranges
Control A
Control B
For 140 : 1 ~ 3 speed control ranges
For 224, 280 : 1 ~ 4 speed control ranges
Fan tap
FM01
224,280 models
Me
Lo
OFF
Fan tap
OFF
FM01
Hi
Hi
Me
Lo
OFF
FM 02
ON
OFF
OFF
OFF
OFF
OFF
(c) In cases of 224 and 280 only, the low outdoor air cooling control is releases temporarily when the number of operating compressors is changed (1 unit 2 unit) and the outdoor fan is operated in the Hi mode. The low outdoor air temperature cooling control
becomes effective 2 minutes later.
(12)
OFF
(13)
CnG
OFF
Open/short
Normal operation
Open
Cooling
Short
Heating
ON
Operation
Note (1) SW-7 is at OFF and CnG is open at the shipping from factory.
833
FDC-HKX
(14)
834
FDC-HKX
(17) FILTER sign
When the operation time (time when the ON/OFF switch is turned to ON) is counted up at 600 hours (1), the filter sign on the
remote controller flickers.
This condition can be reset any time with the Filter reset switch. It is effective also to turn power OFF to reset.
Note (1) The function is invalidated if the jumper wire (J4) is opened. (See page 911 for the location of PCB.)
(18) Auto Swing Control (Excepted FDR, FDUM, FDFL, FDFU models)
(a) Have a louver motor to move the louvers up and down for the so called AUTO SWING function.
(b) The louver auto swing starts when the AUTO SWING switch is pressed once and stops when the AUTO SWING switch is
pressed again. The louver position is displayed on the LCD on the remote controller. During auto swing, the position displayed
on the LCD changes, but the positions of the louvers and the display are not coordinated. (The louvers swing3-4 times per
minute but the display changes once per second.)
(c) Stopping the louvers
When the AUTO SWING switch is pressed to stop the louver movement, the LCD louver-position display stops and the louvers
stop when they come to the position displayed on the LCD. There are four louver stop position on the LCD. (When jumper wire
J2 on the indoor unit printed circuit borad is cut, the louvers stop immediately at the AUTO SWING switch is pressed to stop
them and the LCD display changes to show this posiition. Refer to page 911 for position of jumper wire J2.
(d) Movement of louver when the power supply to the controller controlling 4 positions of the louver is switched on.
When power supply is switched on, the louver will automatically swing about 2 times (without operating remote controller).
This is an action for the microcomputer to confirm the louver position in order to input the cycle of the luver motor (LM) to the
microcomputer with the limit switch (LS) pushing the louver motor (LM). If the LS action is not input to the microcomputer, the
louver will stop within 1 minute after the power supply is switched on and will not move from then on.
(e) Keeping the louvers horizontal during heating
While HOT KEEP is displayed (during hot start operation or when the thermostat has turned off during heating operation), the
louvers stay in the horizontal position to prevent cold drafts, independent of the setting of the AUTO SWING switch (auto swing
or stop). The louver position display of LCD displays continuously the original position before this control operation. When the
HOT KEEP display goes out, both the louver and the LCD display return to their previous positions. (However, after the power
supply to the unit is switched on, the louvers swing two times as a check of the power source frequency, regardless of the setting
of the ON/OFF or AUTO SWING switches.)
(19) Condensate pump motor (DM) control (Only FDT, FDTW, FDTS, FDR, FDUM models)
(a) Drain motor is started no sooner than the compressor is turned ON during cooling or dehumidifying operation. The drain motor
continues to operate for 2 minutes after the stop of unit operation, stop with the error stop, thermostat stop and at switching from
cooling or dehumidifying operation to blowing or heating operation. When there is any unit subjected to oil return control, the
drain motor is operated for 3 minutes at such occasion.
Note (1) Drain motor may be operated forcibly by turning ON the dip switch SW5-3 on the PCB. Turn the switch OFF to stop the drain motor.
(b) Overflow detection is always operable by means of the float switch regardless of operation modes. If the overflow is detected (or
when the float switch is disconnected or its wire is broken), operation is stopped with the error stopped. (FDT, FDTW, FDTS,
FDR and FDUM) If the overflow is detected while the drain motor is stopped, the drain motor is operated for 3 minutes and then
the overflow detection is performed to judge whether it is normal or not.
835
FDC-HKX
Indoor unit operation mode
OFF (1)
COOL
DRY
During compressor ON
FAN (2)
HEAT
Control A
Control B
Operation mode?
Control A
*1
NO
Drain motor ON
Error stop E9
Drain motor ON
3 minutes
after float operation?
Compressor OFF
YES
3 minutes
after float operation?
NO
10 seconds after
drain motor OFF?
YES
Reset
Operation
Reset
Drain motor OFF
Error stop E9 continues
Float SW?
Operation
End
Float SW?
Float operation?
Error stop E9
Drain motor 3-minute ON
Drain motor ON continues
* 1 In the flow in the frame of broken line, operations of operation mode change and thermostat reset are effective and operated immediately upon selection. However,
the compressor ON command is not transmitted.
(1) Control A
a) If the float switch detects the draining, operation is stopped with the error stop (E9 is displayed) and operate the drain pump.
b) Float switch is checked 3 minutes later on the unit stopped by the error and, if the error persists still, the drain motor is left at
ON but, if the error has already been reset, the drain motor is turned OFF. E9 is displayed till the error is reset.
(2) Control B
a) If the float switch detects the draining, the expansion valve is closed, the drain motor is turned ON for 3 minutes and, as 10
seconds elapses after the drain motor OFF, the float switch is checked. If the result is normal, the operation stops in the
normal way while, if it is not normal, E9 is displayed, the drain motor is turned ON and the operation stops with the error stop
with the expansion valve being closed completely. (It is left at ON while the draining is detected.)
(20) External control (remote display)/control of input signal
(a) External control (remote display) output
Following output connectors (CNT) are provided on the control circuit board of indoor unit.
(i)
Operation output: Power to engage DC 12V relay (provided by the customer) is outputted during operation.
(ii) Heating output: Power to engage DC 12V relay (provided by the customer) is outputted during the heating operation.
(iii) Compressor ON output: Power to engage DC 12V relay (provided by the customer) is outputted while the compressor is
operating.
(iv) Error output: When any error occurs, the power to engage DC 12V relay (provided by the customer) is outputted.
836
FDC-HKX
(b) Control of input signal
(Make sure to connect the standard remote control unit. Control of input signal is not available without the standard remote control unit.)
Control of input signal (switch input, timer input) connectors (CNT) are provided on the control circuit board of the indoor unit.
However, when the operation of air conditioner is under the Center Mode, the remote control by CnT is invalid.
(i) At shipping from factory (SW5-1 on PCB OFF)
1) Input signal to CnT OFF ON [Edge input] Air conditioner ON
2) Input signal to CnT ON OFF [Edge input] Air conditioner OFF
ON
ON
CnT Input
OFF
A Unit
OFF
B Unit
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
(ii) When SW5-1 on the PCB of indoor unit is turned on at the field.
Input signal to CnT becomes valid at OFF ON only and the motion of air conditioner [ON/OFF] is inverted.
ON
CnT Input
OFF
A Unit
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
B Unit
OFF
(21) Multiple Units Control-Simultaneous Control of 16 unit with one remote controller
(a) Function
Multiple units (even of outdoor different systems, 16 units maximum) can be simultaneously controlled by using a remote
control switch (a special order item). The remote control switch is used to set the operation mode, and all the unit can be
operated and stopped at intervals of 0.5 to 1 second in the order of unit number. Thermostat and protective functions of each
unit functions independently.
Note(1) When part of the group gets out of order (the protective device operates), the relevant unit comes to an abnormal stop, but other normal units keep operating.
Outdoor
unit
Signal wire
Indoor
unit
No.1
Indoor
unit
No.2
Indoor
unit
No.3
(2)
Remote control
signal wire
Outdoor
unit
(1)
Indoor
unit
No.16
(2)
Remote control
signal wire
Notes (1) The overall length of the signal wire shall be less than 1000m.
(2) The length of remote control signal wire and crossover for remote controller between room shall be less than 600m.
837
FDC-HKX
(22) External input operation
External input: From CnS1, operation permission/prohibition control; From CnS2: Demand control/normal operation switching.
J1: Switches between CnS1 and CnS2 input method.
J1 short circuit: Level input by CnS1 and CnS2.
J1 open: Pulse input by CnS1 and CnS2.
(a)
Input : CnS1
Short
circuit
Disconnection
Short
circuit
(NOP)
J1; Disconnection
1)
The remote controller displays the operating mode. To Option sends the operating mode.
2)
CnS1, performs the following operations by the changing of jumper wire J1 from short circuit to open circuit.
If pulse input, the pulse duration is 500 ms or more.
1 Opreation with J1 short circuit
ON (shorted)
Air conditioner ON OK
CnS1 input
OFF (open)
OFF (open)
ON
ON
OFF
ON
Center
Center
Remote
OFF
OFF
ON
OFF
ON
OFF
ON
Air conditioner ON OK
CnS1 input
ON
OFF
Air conditioner ON OK
ON
ON
ON
OFF
Center
Remote
ON
Air conditioner ON/OFF
838
Center
OFF
Remote
ON
Center
FDC-HKX
(b) From CnS2, operation permission/prohibition control
Input : CnS2
Short
circuit
Open
circuit
Short
circuit
Open
circuit
Demand control
Normal operation
Normal operation
Demand control
(NOP)
Note (1) The factory settings are: J1 - short circuit; CnS2 - short circuit (short pin connection)
1)
The remote controller displays the operating mode. To Option sends the operating mode.
2)
Demand control
Sets all compressors to OFF.
3)
CnS2, performs the following operations by the changing of jumper wire J1 from short circuit to open circuit.
If pulse input, the pulse duration is 500 ms or more.
1 J1 - Short circuit
CnS2 input
ON (shorted)
OFF (open)
ON (shorted)
Normal
Demand control
Normal
ON
OFF
ON
OFF
Remote
Compressor
OFF
OFF
ON
Compressor OFF
OFF
OFF
2 J1 - Open circuit
ON
OFF
ON
Demand control
OFF
Demand control
CnS2 input
ON
OFF ON
OFF
Compressor
OFF
839
FDC-HKX
19.5 APPLICATION DATA
SAFETY PRECAUTIONS
Please read these Safety Precautios first then accurately execute the installation work.
Though the precautionary points indicated herein are divided under two headings,
WARNING and
CAUTION , those
points which are related to the strong possibility of an installation done in error resulting in death or serious injury are listed in
the
WARNING section. However, there is also a possibility of serious consequences in relationship to the points listed in
the
CAUTION section as well.
In either case, important safety related information is indicated, so by all means, properly observe all that is mentioned.
After completing the installation, along with confirming that no abnormalities were seen from the operation tests, please explain
operating methods as well as maintenance methods to the user (customer) of this equipment, based on the owners manual.
Moreover, ask the customer to keep this sheet together with the owners manual.
WARNING
This system should be applied to places of office, restautant, residence and the like. Application to
inferior environment such as engineering shop could cause equipment malfunction.
Please entrust installation to either the company which sold you the equipment or to a professional
contractor. Defects from improper installations can be the cause of water leakage, electric shocks
and fires.
Execute the installation accurately, based on following the installation manual. Again, improper installations can result in water leakage, electric shocks and fires.
When a large air-conditioning system is installed to a small room, it is necessary to have a prior
planned countermeasure for the rare case of a refrigerant leakage, to prevent the exceeding of threshold concentration.
In regards to preparing this countermeasure, consult with the company from which you purchased the
equipment, and make the installation accordingly. In the rare event that a refrigetant leakage and
exceeding of threshold concentration does occur, there is the danger of a resullant oxygen deficiency
accident.
For installation, confirm that the installation site can sufficiently support heavy weight. When strength
is insufficient, injury can result from a falling of the unit.
Execute the prescribed installation construction to prepare for earthquakes and the strong winds of
typhoons and hurricanes, etc. Improper installations can result in accidents due to a violent falling
over of the unit.
For electrical work, please see that a licensed electrician executes the work while followig the safety
standards related to electrical equipment, and local requlations as well as the installation instructions,
and that only exclusive use circuits are used.
Insufficient power source circuit capacity and defective installment execution can be the cause of
electric shocks and fires.
Accurately connect wiring using the proper cable, and insure that the external force of the cable is not
conducted to the terminal connection part, through properly securing it. Improper connection or securing can result in heat generation or fire.
Take care that wiring does not rise upward, and accurately install the lid/service panel. Its improper
installation can also result in heat generation or fire.
When setting up or moving the location of the air-conditioner, do not mix air etc. or anything other
than the designated refrigerant within the refrigeration cycle.
Always use accessory parts and authorized parts for installation construction. Using parts not authorized by this company can result in water leakage, electric shock, fire and refrigerant leakage.
CAUTION
Execute proper grounding. Do not connect the ground wire to a gas pipe, water pipe, lightning rod or
a telephone ground wire. Improper placement of ground wires can result in electric shock.
The installation of an earth leakage breaker is necessary depending on the established location of the
unit. Not installing an earth leakage breaker may reslut in electric shock.
Do not install the unit where there is a concern about leakage of combustible gas.
The rare event of leaked gas collecting around the unit could result in an outbreak of fire.
For the drain pipe, follow the installation manual to insure that it allows proper drainage and thermally
insulate it to prevent condensation. Inadequate plumbing can result in water leakage and water damage to interior items.
840
FDC-HKX
19.5.1 Installation of indoor unit
(1) Ceiling recessed type (FDT)
400
420
637
422
Drain hose
(accessory)
Attach on site.
Hang bolt
267
310
840
Unit : mm
d
210
260
270
320
137
167
d
FDT112, 140
Hanger
D
Control box
Refrigerant piping
Drain
Main
body
Hang bolt
Nut
Washer
Spring
Washer
In-door unit
Level gauge
Hose
10~25
40~45
Request
For the hang bolt whose length exceeds 1.3m, use the M10 size
hang bolt and moreover combine a diagonal member to the hang
bolt for reinfocement.
45 and over
Model
FDT28, 36, 45,
56, 71, 90
A B
C
c
(c) Hanging
Arrange four sets of a hang bolt (M10 or M8), a nut for it, a
plain washer and a spring washer on site.
332
30
95
Ceiling
member Level gauge (insulation)
841
FDC-HKX
(d) Drain Piping
1) Drain piping should always be in downhili grade (1/50 ~ 1/100) and avoid riding across and elevation or making traps.
Good piping
Suspension
bolts
Improper piping
Avoid riding across an elevation
1.5 m ~ 2 m
Air vent
Heat
A downhill grade
insulation of 1/100 or more
2)
3)
4)
5)
6)
7)
8)
700 mm or less
9)
When connecting the drain pipe to unit, pay sufficient attention not to applay excess force to the piping on the unit side. Also,
fix the piping at a point as close as possible to the unit.
For drain pipe, use hard PVC general purpose pipe VP-25(I.D.1)
Stage
difference Drain hose
which can be purchased locally. When connecting, insert a PVC
Drain socket part
pipe end securely into the drain socket before tightening securely
using the attached drain hose and clamp. Adhesive must not be
VP25 joint
Pipe cover (large) (field purchased)
used connection of the drain socket and drain hose (accessory).
[for insuation]
(accessory)
When consturcting drain piping for several units, position the comMain unit
mon pipe about 100 mm below the drain outlet of each unit as
shown in the sketch. Use VP-30(11/4) or thicker pipe for this
Drain hose
VP25
(accessory)
(field purchased)
purpes.
Clamp
Adhesion
Pipe cover
Be sure to provide heat insulation to hard PVC pipes of indoor
Drain socket (accessory)
[for insuation]
Pipe cover (small)
(field purchased)
placement.
[for insuation]
(accessory)
Do not ever provide an air vent.
The height of the drain head can be elevated up to a point 700 mm ablve the
ceiling and, when an obstacle exisits in the ceiling space, elevate the piping to
avoid the obstacle using an elbow or corresponding gadget. When doing this, if
Secure the elevation as high as possible
(approx. 100 mm)
the stretch for the needed height is too high, the back-flow quantity of drain at the
event of interruption of the operation gets too much and it may cause overflow at
the drain pan. Therefore, make the height of the drain pipe within the distance
given in the sketeh below.
A downhill grade of
VP30
1/100 or more
Avoid positioning the drain piping outlet at a place where generation of odor may
be stimulated. Do not lead the drain piping direct into a sewer from where sulfur
295 ~ 325 mm
100 mm or less
gas may generate.
The purpose of drain hose is to absorb minute discrepancy of the unit or the drain
Drain hose
piping occurred when they are installed. Therefore, when it is bent intentionally
or used under expanded condition, it may be damaged and result in water leakage.
Drainage Test
1 Conduct a drainage test after completion of the electrical work.
VP25 joint
(field purchased)
2 During the trial, make sure that drain flows properly through the piping and that no water leaks from connections.
3 In case of a new building, conduct the test before it is furnished with the ceiling.
4
Be sure to conduct this test even when the unit is installed in the heating season.
Procedures
1
Supply about 1000 cc of water to the unit through the air outlet by using a feed water pump.
Pour water into a convex joint
Put the tip of the feed water pump
in the drain pan of the unit body
If the electrical work has not been completed, connect a convex joint in the drain
pipe connection to provide a water inlet.
Then, check if water leaks from the piping system and that drain flows through
the drain pipe normally.
2 Check at the exhaust port if drain is flowing.
(Note) Conduct this test paying attention to rotating sound of the drain motor.
3 Remove the drain plug located on the bottom of the drain pan when the water has to be evacuated from the unit.
4 After the test, fit the drain plug to the original place and turn off the power source.
842
FDC-HKX
(e) Fixing of Decorative Panel (The panel fixing bolts are attached on the panel.)
1)
Check with the accessory level gauges that indoor unit height and the size of ceiling hole are correct.
Remove the level gauges from the indoor unit before fixing the decorative panel.
2)
Screw two bolts out of four accessory bolts less than 5 mm in the indoor unit diagonally.
3)
Hang the panel on the two bolts and fix them temporarily.
4)
Tighten the bolts fixed temporarily and the remaining two bolts.
Screw the remaining two bolts, and tighen all (four) bolts.
5)
6)
If the louver motor is not operated by remote control, check if the connector is connected correctly, and turn off the power for
more then 10 seconds, then reset it.
If it is fixed in other way, air will leak. Also, wires cannot be connected for auto swing and receiver amp.
Louver motor
Electrical
equipment
box
Refrigerant piping
Drain piping
843
FDC-HKX
(2) 2-way outlet ceiling recessed type (FDTW)
(a) Selection of installation location
1)
This unit is a ceiling surface direct return air and direct supply air type.
Install the unit a place the allows air to reach every part of the room, in accordance with the shape and heigh of the room.
Installation space
100
or
more
2)
1000
or more
Unit : mm
100
or
more
1500
or
more
1500
or
more
This unit permits connecting a branch duct (B 200 mm) according to the method shown in the figure below so that air
disribution may be improved to the shape of the room. (For the connecting port of the duct, refer to the exterior dimension
on page 760.)
200
mm
Air interruption
Unit : m
Models
FDTW28, 45, 56 type
FDTW71, 90 type
FDTW112 type
FDTW140 type
Item
Standerd
4.0
4.5
4.7
5.0
UHi
4.5
5.0
5.2
5.5
Note (1)
4)
Places where chilied or heated air circulates freely. When the installation heiht exceeds 3.5m, warmed air stays close to the
ceiling. In such cases, suggest your client users to install air circulators.
5)
Places where perfect drainage can be prepared and sufficient drainage gradient is available.
6)
Places free from air disturbances to the return air port and supply hole of the indoor unit, places where the fire alarm may
not malfunction to short circuit.
7)
Places with the environmental dew-point temperature is lower than 28C and the relative humidity is less than 80%. (When
installing at a place under a high humidity environment, pay suffcient attention to prevention of dewing such as thermally
insulating the unit properly.)
844
FDC-HKX
8)
Places exposed to oil splashes or steam (e.g. kitchens and machine plants.)
Installation and use at such places will incur deteriorations in the performance or corrosion with the heat exchanger or
damage in molded synthetic resin parts.
9)
Places where corrosive gas (such as sulfurous acid gas) or inflammable gas (thinner, gasoline, etc.) is generated or remains.
Installation and use at such places will cause corrosion in the heat exchanger and damage in molded synthetic resin parts.
10) Place adjacent to equipment generating electromagnetic waves or high-frquency waves such sa in hospitals. Generated
noise may cause malfunctioning of the controller.
(b) Preparations for installation
1)
a) The pattern sheet shrinks or expands as humidity changes, so check the actual size before use.
b) The ceiling hole sizes and suspension bolt sizes are shown in the following figure.
70
Center panel
97
50
640
Control box
97
446
Suspension bolt pitch
40
Dimension table
Unit : mm
Mark
FDTW28, 45, 56
type
1015
885
468
417
FDTW71, 90 type
1260
1130
590
540
FDTW112, 140
type
1730
1600
825
775
Models
(c) Installation
For the suspension bolt, use four M10 or W 3/8 bolts and secure so that each bolt can withstand a 50 kg/f pullout load.
Use a suspension bolt length that extends approximately 95 mm for the ceiling surface.
845
FDC-HKX
A. If there is a ceiling
1)
2)
Outlet
port
designated locations.
(Use care as the center of the spacing for the suspension
Ceiling surface
Hang the unit, use the four bolts to mount the pattern
paper provided to the panel mounting section and adjust
4)
Printed surface
the height.
Use a level or transparent hose with water in it to
confirm that the unit is level. If the unit is not level,
problems such as water leakage or improper operation
of the float switch could occur.
5)
Vinyl tube
2)
3)
Drain piping should always be in a downhill grade (1/50-1/100) and avoid riding across an elevation or making traps.
Good piping
Suspension
bolts
Improper piping
Avoid riding across an elevation
1.5 m ~ 2 m
Air vent
Heat
insulation
846
A downhill grade
of 1/100 or more
FDC-HKX
2)
When connecting the drain pipe to the unit, pay suffcient attention not to apply excess force to the piping on the unit side. Also,
3)
For drain pipe, use hard PVC ganeral purpose pipe VP-25 (I.D.1'') which can
Drain socket
be purchased locally. When connecting, insert a PVC pipe end securely into
the drain socket before tightening securly using the attached drain hose and
clamp. Adhesive must not be used connection of the drain socket and drain
hose (accessory).
Unit
VP-25
Drain hose
(local procurement)
Clamp
Drain socket (accessory)(accessory)
Adhesion Pipe cover [insulation]
Pipe cover (small)[insulation]
(local procurement)
(accessory)
4)
When constructing drain piping for several units, position the common pipe about 100mm below the drain outlet of each unit
as shown in the sketch below. Use VP-30 or thicker pipe for this pupose.
Secure the elevation as high as possible
(approx. 100 mm)
A downhill grade of
1/100 or more
VP30
5)
6)
7)
The height of the drain head may be elevated up to a point 750mm above the ceiling and, when an obstacle exists in the ceiling
space, elevate the piping to avoid the obstacle using an elbow or corresponding gadget. When doing this, if the stretch for the
needed height is too high, the back-fiow quantity of drain at the time of interruption of the operation gets too much and it may
cause overflow at the drain pan. Therefore, make the height of the drain pipe withing the distance given in the drawing below.
295~325
100 mm or less
750 mm or less
8)
Avoid positioning the drain piping outlet at a place where ganeration of odor may be stimulated. Do not lead the drain piping
direct into a sewer from where sulfur gas may generate.
847
FDC-HKX
Note (1) If the connector remains connected, drain water is discharged from the standard pipe connecting port, leading to water
leakage.
Drainage Test
When using the standard drain port, execute a drainage test after completion of electric work.
1 During the test run, make sure that drain flows properly through the piping and that no water leaks from connections.
2 Be sure to conduct this test even when the unit is installed in the heating season.
3 In case of a new building, conduct the test before it is furnished with the ceiling.
1)
Inject about 1,000cc by using a feed water pump from the grommet on the drain pump side.
2)
3)
After completion of the drain test, completely perform heat insulation fot the drain pipe up to the main unit.
(g) Fixing of Panel ( The panel fixing bolts are attached on the panel. )
Note (1) Care should be exercised in handling the supply air port on the panel because it is easily depressed by finger nail.
1)
Check with the accessory level gauges that the indoor unit height and the size of ceiling hole are correct.
Notes (1) Remove the level gauge from the indoor unit befroe fixing the panel.
(2) Remove the Air inlet panel from the panel proper.
Pin (B)
Panel proper
Pin (A)
Panel outer frame
Remove
848
FDC-HKX
a)
Remove the panel from the pin (A) in the order of the arrows 1 and 2.
b)
Open the panel slightly as shown by the arrow 3 and move it to the arrow 4. Then remove it from the pin (B).
2)
Screw two bolts out of four accessory bolts less than 5mm in the panel diagonally.
3)
4)
Tighten the bolts fixed temporarily and the remaining two bolts.
5)
Connect the louver motor connector (white, 3P) and the limit switch connector (white, 2P) to the panel respectively.
6)
When the louver motor cannot be operated by remote controller operation, check the connector connections and turn off the
power suppy for 10 sceonds or more for restting.
Ceiling material
FDTW28, 45, 56
type
FDTW71, 90 type
FDTW112, 140
type
Width
300
300
300
Length
970
1215
1685
Item
10 ~ 15 mm
849
FDC-HKX
(3) 1-way outlet ceiling recessed type (FDTS)
B Higher ceiling
Ceiling
Ceiling
3m ~ 4m
3m or less
Floor
Floor
Note (1) In the case of installing on the high ceiling, part of indoor unit requires some modification.
Procedures of rework
Installation on higher ceiling
Adhere the insulation materials attached to the direct blow panel on the blow outlet of indoor unit.
Blow outlet
Insulation materials
Reference
Reaching distance
Standard
Models
All models
Higher ceiling
7
2. Kind of operation: Hi
3. Place: Free space without obstruction;
4. Reaching distance means the horizontal distance for the wind to reach the floor.
5. Wind velocity at the reaching distance: 0.5m/s
Note (1) Wind capacity is UHi in case of a higher ceiling. It is value of Hi for other cases.
2) Where the ceiling has sufficient rigidity.
3) Where there is no obstacles in front of the suction intel and blow outlet.
4) It should be avoided such places as kitchen, machine factory, etc. where there profuse liquid splashes or thick steam.
5) Where the height of ceiling exceeds 200mm.
850
FDC-HKX
Where a space as shown below can be secured.
Unit : mm
100
or more
1000
or more
2000
or more
6)
100
or more
Obstacle
7)
8)
Select a place to branch the piping so that same distance will be a obtained for each of one way piping.
9)
Where humidity may exceed 80% behind the ceiling or the dew point may exceed 28C, adhere polyurethane foam materials
(t 10 or more) over the insulation materials on the external plate.
10) Where it is convenient for the piping and wiring to the outdoor.
11) Where protected from direct exposure to sun beams.
12) Where it is free from volatile gas generation.
(b) Standard Iocation
1) Installation
1
(Suspension bolt pitch)
30
Panel dimensions)
(Air outlet)
(Ceiling ~
panel lap
dimensions)
40
600
30
(Ceiling ~ panel lap
dimensions)
2
(Ceiling hole size)
3
(Panel dimensions)
Unit : mm
Mark
990
1230
1290
180
FDTS71 type
1250
1440
1500
145
Models
100 mm
or less
30mm.)
Suspension bolt
(M10)
Unit
851
FDC-HKX
c) Fixing of Suspension bolt. Fix the bolts securely as shown below or by any other adequate means.
Insert
Concrete
Suspension
bolt, M10
d) Installation
Drain pump box
Unit
Procedures
1 Install nuts on the Suspension bolts at onside. Suspension the suspension fixtures on the Suspension bolts first and then insert the
remaining fixtures on the remaining Suspension bolts at and lock them with nuts.
2 Since the indoor unit and the panel height cannot be adjusted, adjust the height using an attached pattern before fixing the indoor
unit.
Ceiling board
Pattern
Pattern
securing
screw
(attached)
Detail - Section A
852
25
FDC-HKX
Check of levelness
Check the levelness as follows. Use a level gauge or adjust the levelness with the following method.
Adjust the bottom of main unit
and the water level as shown
below.
Piping side
Water injection
Water level
0~3 mm
Vinyl pipe
2) Drain pipe
a) Set the drain pipe as a declining gradient (1/50 ~ 1/100) and avoid to cross an over-hand ridge or to allow a trap on the way.
Good piping
Support fixture
Improper piping
1.5m~2m
Crossing
over-hang ridge
Air bleed
Declining gradient
1/100 or more
Trap
Insulation
materials
b)
When connecting the drain pipe, avoid undue stress being applied to the pipe at the unit side and fix the pipe at a point as close
as possible to the unit.
c)
A hard vinyl chloride pipe, general VP-25, which is available from markets is ideal for the drain pipe.
d)
When installing the drain pipe, make sure to use the attached drain pipe, drain pipe clamp, and insulation materials for drain
pipe clamp.
Insert the drain pipe to the base of outlet.
Securely tighten the drain pipe clamp.
Make sure to insulate the drain pipe clamp.
e)
When there are plural number of drain pipes, arrange to position the converging pipe at about 100mm below the drain outlet
as shown below. Use a pipe of VP-30 or higher for the converging pipe.
Should be as high as possible.
(Approx. 100 mm)
f)
Make sure to provide the thermal insulation for the hard vinyl chloride pipe and drain socket provided indoor.
g)
600mm or less
295~325
853
FDC-HKX
Drain test
[Perform this before installing the ornament panel]
Perform this upon completion of electrical work.
Gradually introduce 2,000~3,000cc of water as shown below.
Drain piping connection port
If the electrical work has not been completed, connect a convex joint
in the drain pipe connection to provide a water inlet.
Then, check if water leaks from the piping system and that drain flows
through the drain pipe normally.
Connect the remote control switch and set to cooling operation. The drain pump will operate with the compressor on.
Test whether or not the water is draining while listening to the operating sounds of the electric motor for the drain water.
Unit
Check that water is draining smoothly and that there is no water dripping from the connections or other areas.
Mounting the Panel
1
Open the inlet grille and remove the air block panel from the inside. (Remove the 2 screws.)
854
FDC-HKX
Approx. 15 mm
2 Mount the two (M5 x 35) panel mounting screws to the indoor unit
Detail of Section A
3 Hang the panel on the two mounting screws on the indoor unit by using the two
Sliding direction
4 Use the opening to connect the connectors for the louver motor and limit switches.
Opening
Ceiling opening
Connector
855
FDC-HKX
(4) Cassetteria type (FDR)
(a) Preparation of indoor unit
Before of during the installation of the unit, assemble necessary optional panel, etc. depending on the specific type.
(b) Select places for installation satisfying following conditions and, at the same time, obtain the consent on the
part of your client user.
1) Places where chilled or heated air circulates freely.
When the installation height exceeds 3 m, warmed air stays close to the ceiling. In such cases, suggest your client users to
install air circulators.
2) Places where perfect drainage can be prepared and sufficient drainage.
3) Places free from air disturbances to the suction port and blowout hole of the indoor unit, places where the fire alarm may not
malfunction or short-circuit.
4) Places with the environmental dew-point temperature is lower that 28C and the relative humidity is less than 80%.
( When installing at a place under a high humidity environment, pay sufficient attention the prevention of dewing such as
thermal insulation of the unit prperly.)
(c) Avoid installation and use at those place listed below.
1) Places exposed to oil splashes or steam (e.g. kitchens and machine plants).
Installation and use at such places incur deteriorations in the performance or corrosion with the heat exchanger or damage in
molded synthetic vesin parts.
2) Places where corrosive gas (such as sulfurous acid gas) or inflammable gas (thinner, gasoline, etc) in generated or remains.
Installation and use at such places cause corrosion in the heat exchanger and damage in molded synthetic resin parts.
3) Places adjacent to equipment generating electromagnetic waves or high-frequency waves such as in hospitals.
Generated noise may cause malfunctioning of the controller.
(d) Preparation for installation
1) Selection of suspension pattern
When the unit is hanged from ceiling, select one of following patterns depending on the dimensions of the ceiling.
< Combination with silent panel >
Mark
A
56 ~ 70
Models
FDR22, 28, 45, 56
71, 90 type
365 mm or more
416 mm or more
495 mm or more
510 mm or more
150 ~ 300
856
FDC-HKX
2) Ceiling hole size and position of suspersion bolt
When boring at the ceiling, use the pattern sheet included in the accessory of the unit.
Leave the pattern sheet on the unit till decorative panel is installed.
< Combination with silent panel >
Unit : mm
Mark
786
980
1040
FDR71, 80 type
986
1180
1240
1406
1600
1660
57
A
(Suspension bolt pitch)
B
(Celing hole size)
C
(Panel dimensions)
57
30
(Panel dimensions)
Celing ~ panel
lap dimensions
30
545
70
70
(Suspension bolt pitch)
690
(Celing hole pitch)
750
Models
(Celing ~ panel
lap dimensions)
525
(Ceiling hole size)
585
(Panel dimensions)
90
545
70
(Suspension bolt pitch)
30
Ceiling ~ panel
lap dimensions)
A
(Suspension bolt pitch)
B
(Ceiling hole size)
A
(Panel dimensions)
Unit : mm
Mark
786
804
864
FDR71, 80 type
986
1004
1064
1406
1424
1484
Models
9
30
Ceiling ~ panel
lap dimensions)
Insert
M10 nut
Suspension bolt
M10 washer
Note (1) When the dimensions of indoor unit and ceiling holes does not match, it can be adjusted with the slot holes of
mounting bracket.
857
FDC-HKX
2) Adjusting the units levelness
1 Adjust the out-of levelness using a level vial or by following method.
Make adjustment so that the relation between the lower surface of the unit proper and water level in the hose becomes as
given below.
Piping side
Supply water
Water level
0 ~ 5 mm
PVC hose
Bring the piping side slightly lower.
2 Unless the adjustment to the levelness is made properly, malfunctioning or failure of the float switch may occur.
3) Tap selection on blower unit
Taps of blower unit are set at the standard selection at the shipping from factory. Where the static pressure
is raised by changing the connection of connectors provided at the flank of control box as shown below.
Black
White
Name
Round head machine
screw (M5 x 35)
Red
Blue
Blue
Black
White
Black
Brown
White
Q'ty
Position
4 pcs.
a) Accessory
b) Installation procedures
Panel inner frame
2
.
Open slightly as the arrow 3 and move toward the arrow 4 and detach from pin (B)
Panel outer frame
Pin (B)
Pin (A)
1
2
858
Motor side
Blue
Connector,
white
Red
White
Red
Motor side
Black
Blue
White
Red
Connector,
white
FDC-HKX
Abt. 30 mm
Indoor unit
Temporary
setting
Procedures of installation
1 Secure the panel tentatively with 2 of 4 panel set screws (panel accessory) as shown above.
2 When the panel is supported with a pair of set screws, slide it in the arrow direction.
Note (1) Panel outer frame has the orientation.
3 Lock the former 2 and remaining 2 set screws.
4 Install the panel inner frame in the reverse order of removal.
2) Case of canvas panel
( Canvas duct (option) is necessary to install the canvas panel.)
a) Accessory
Name
Symbol
Q' ty
Position
Panel securing
Chain securing
Holder
Chain
b) Mounting procedures
1 Install the canvas duct (option, 4 places) on the Indoor unit.
Indoor unit
Canvas duct
859
FDC-HKX
2 Remove the panel inner frame.
It can be removed same as the silent panel.
Pin (B)
Pin (A)
Panel outer frame
1
2
Procedures of installation
Panel outer frame
Canvas duct
Holder
860
Abt. 20 mm
Indoor unit
4 Holder
3 Round head screw
FDC-HKX
Hook the chain of panel outer panel on the holder.
Note (1) When hooking the chain.
make sure to avoid slackness on it by pushing
hard the panel outer
frame against the ceiling
material.
Ceiling material
Tighten 3 screw in the step 1 till the panel outer frame contacts closely with the ceiling material.
Secure the canvas duct and the panel outer frame with screws.
Canvas duct
5 Remove the panel inner frame and install in the reverse order of removal.
6 Cautions for duct installation work
Indoor unit
Convas duct
(Optional
parts)
Heat
insulation
Ceiling surface
Return air
port panel
Silent panel
Return air
port panel
(Canvas panel)
Calculate the draft and external static pressure and select the length, shape and blowout.
Supply air duct
1-spot, 2-spot, 3-spot and 4-spot with 200 type duct are the standard specifications. Determine the number of spots based on
following table.
FDR22 type
FDR71, 90 type
1-spot
2-spot
2 ~ 3-spot (1)
3 ~ 4-spot (1)
Notes (1) Shield the central supply air port for 2-spot.
(2) Shield the supply air port around the center for 3-spot.
Bad example
Good example
861
FDC-HKX
Use a band, etc. to connect the indoor unit and the supply air duct flange.
Conduct the duct installation work before finshing the ceiling.
(g) Connection of air inteke and exhaust ducts.
Fig.2
Ceiling material
Ornament plate
Attachment procedures
1 Remove the stopper.
2 Remove the ornament plate and attach the ceiling material.
3 Hold down the ceiling material and return the stopper in position.
Note (1) If the ceiling material is attached, the ornament plate is not used.
862
FDC-HKX
(h) Drain piping
1) Drain piping should always be in a downhill grade (1/50-1/100) and avoid riding across an elevation or making traps.
Improper piping
Good piping
Suspension
bolts
Heat
insulation
A downhill grade
of 1/100 or more
2) When connecting the drain pipe to the unit, pay suffcient attention not to apply excess force to the piping on the unit side.
Also, fix the piping at a point as possible to the unit.
Drain socket
3) For drain pipe, use hard PVC general purpose pipe VP-25 which can be purchased
locally. When connecting, insert a PVC pipe end securely into the drain socket before tightening securely using the attached drain hose and clamp. Adhesive must not
be used connection of the drain socket and drain hose (accessory).
Main
unit
VP-25
(local procurement)
Drain hose
Clamp
Drain socket
(accessory) (accessory)
Pipe cover [insulation]
Pipe cover (small)[insulation]
Adhesion (local procurement)
(accessory)
4) When constructing drain piping for several units, position the common pipe about 100mm below the drain outlet of each unit
as shown in the sketch below. Use VP-30 or thicker pipe for this purpose.
A downhill grade
of 1/100 or more
VP-30
Drain hose
600 mm
(local maximum
height of drain head)
295 ~ 325
Right above
8) Avoid positioning the drain piping outlet at a place where ganeration of odor may be stimulated. Do not lead the drain piping
direct into a sewer from where sulfur gas may ganerate.
863
FDC-HKX
9) Drainage test
a) During trial operation, make sure that drainage is properly execued and check that leakage is not found at connections.
b) Be sure to carry out a drainage test when installing the system during a heating season.
c) When installing the system in a building under construction, carry out the drainage test before ceiling tiles are installed.
Insert a water filing hose by approx 50 mm and feed water.
(Be sure to insert the water filing hose in a downward direction.)
1 Supply approx 1000cc of water through the outlet of the unit using a feed water pump.
2
Make sure that drainage is proceeding properly at the see-through outlet of the unit.
*Also confirm the revolving sound of the condensate motor when checking the drainage.
3 Then remove the drain plug at lower section of the unit to drain water off. After making sure water is not left, restore the
drain plug to the original position.
10) Drainage from the lower drain socket
Only if the drain pipe can be in-
(Piping connection)
A hard PVC general-purpose pipe
pipe as illustrated.
Heat insulator
Rubber plug
(Remove the rubber plug)
drain motor)
As shown in the sketch to the right, disconnect the drain motor
connector CnR (blue color coding).
Caution:
If the system is started with this
connector connected as is, drain
water is discharged out of the upper drain socket causing a heavy
water lekage.
864
Disconnect Condensate
motor connector
CnR (2P Blue)
FDC-HKX
(5) Satellite ducted type (FDUM)
(a) Selection of installation location
1)
2)
Select places for installation satisfying the following conditions and, at the same time, obtain the consent on the part of your
client user,.
a) Places where chilled or heated air circulates freely. When the installation height exceeds 3m, warmed air stays close to the
ceiling. In such cases, suggest your client users to install air circulators.
b) Places where perfect drainage can be prepared and sufficient drainage gradient is available.
c) Places free from air disturbances to the return air port and supply hole of the indoor unit, places where the fire alarm may not
malfunction to short circuit.
d) Places with the environmental dew-point temperature is lower than 28C and the relative humidity is less than 80%.
( When installing at a place under a high humidity environment, pay sufficient attention to prevention of dewing such as
thermally insulating the unit properly.)
Check if the selected place for installation is rigid enough to stand the weight of thew unit.
Otherwise, apply reinforcement using boards and beams before starting the installation work.
Unit : mm
600
620
Models
Mark
1100
FDUM71, 90 type
1300
1720
A
100
3)
865
FDC-HKX
(b) Suspension
Be sure to observe the finished length of the suspension bolts given below.
Unit : mm
Mark
545
Models
786
FDUM71, 90 type
986
1406
Insert
Concrete
Suspension bolt M10
Suspension bolt
M10 nuts
M10 Washer
Indoor unit
60mm or less
Indoor unit
Piping side
Supply water
0 ~ 5 mm
PVC hose
b) Unless the levelness is adjusted properly, the malfunction of the float switch will occur.
3) Tap selection on blower unit.
Taps of on blower unit are set at the standard selection at the shipping from factory. Where the static pressure is raised by
changeing the connection of connectors provided at the flank of control box as shown below.
High speed tap
866
Black
White
Blue
Black
White
Blue
Black
Brown
White
Motor side
White
Blue
Red
Connector,
white
Connector,
red
Black
Blue
Red
Motor side
Red
Connector,
white
Connector,
white
FDC-HKX
(c) Duct installation
1 Supply air duct
(to be purchased locally)
Heat insulation
Indoor unit
Supply air port
(to be purchased locally)
2 Access door
Fig.2
867
FDC-HKX
(d) Drain piping
1) Drain piping should always be in a downhill grade (1/50-1/100) and avoid riding across an elevation or makeing traps.
Improper piping
Good piping
Suspension
bolts
1.5 m ~ 2m
Air vent
Heat
insulation
A downhill grade
of 1/100 or more
2) When connecting the drain pipe to the unit, pay suffcient attention not to apply excess force to the piping on the unit side.
Also, fix the piping at a point as close as possible to the unit.
3) For drain pipe, use hard PVC general purpose pipe VP-25 which can be purchased
Drain socket
locally. When connecting, insert a PVC pipe end securely into the drain socket before
tightening securely using the attached drain hose and clamp. Adhesive must not be used
connection of the drain socket and drain hose ( accessory).
Main
unit
VP-25
(local procurement)
Drain hose
Clamp
Drain socket
(accessory) (accessory)
Pipe cover [insulation]
Pipe cover (small)[insulation]
Adhesion (local procurement)
(accessory)
4) When constructing drain piping for several units, position the common pipe about 100 mm below the drain outlet of each
unit as shown in the sketch below. Use VP-30 or thicher pipe for this purpose.
Secure the elevation as high as possible
(approx. 100 mm)
A downhill grade of
1/100 or more
VP30
600 mm
(local maximum
height of drain head)
295 ~ 325
Right above
8) Avoid positioning the drain piping outlet at a place where generation of odor may stimulated. Do not lead the drain piping
direct into a sewer from where sulfur gas may generate.
868
FDC-HKX
9) Drainage test
a) During trial operation, make sure that drainage is properly execued and check that leakage is not found at connections.
b) Be sure to carry out a drainage test when installing the system during a heating season.
c) When installing the system in a building under construction, carry out the drainage test before ceiling tiles are installed.
Insert a water filing hose by approx 50 mm and feed water.
(Be sure to insert the water filing hose in a downward direction.)
1 Supply approx 1000cc of water through the outlet of the unit using a feed water pump.
2
Make sure that drainage is proceeding properly at the see-through outlet of the unit.
* Also confirm the revolving sound of the condensate motor when checking the drainage.
3 Then remove the drain plug at lower section of the unit to drain water off. After making sure water is not left, restore the
drain plug to the original position.
The upper drain socket
(Piping connection)
Heat insulator
Rubber plug
(Remove the rubber plug)
Disconnect Condensate
motor connector
CnR (2P Blue)
869
FDC-HKX
(6) Ceiling Supension type (FDE)
(a) Selection of installation location
1) A place where good air circulation and delivery can be obtained.
FDE71 type
FDE112 type
FDE140 type
Air throw
7.5
9.5
10
Conditions
(1) Installation height: 2.4 ~ 3.0 m above the floor
(2) Fan speed: Hi
(3) Location: Free space without obstacles
(4) Distance of reach indicates the horizontal distance after the wind touched down the floor.
(5) Air velocity at the throw: 0.5 ( m/sec.)
2)
3)
A place where there is no obstruction to the return air inlet and supply air outlet ports.
4)
Places exposed to oil splashes or steam (e.g. kitchens and machine plants).
Installation and use at such places will incur deteriorations in the performance or corrosion with the heat exchanger or damage
in molded synthetic resin parts.
5)
300 or more
100 or more
150 or more
5 or more
Obstacle
6)
This unit uses a mincrocomputer as a control device. Therefore avoid installing the unit near the equipment that generates
strong electromagnetic waves and noise.
870
FDC-HKX
b) Positions of suspension bolts are as in the drawing below.
When the suspension brackets face out
Suspemsion
bolt hole
Suspemsion
bolt hole
650
Air
outlet
50
31
B
D
Suspension
bracket
240
5
240
5
Suspemsion
bracket
50
31
140 275
A
Air
outlet
140 275
650
8
31
C
D
8
31
Unit : mm
Mark
1000
900
984
938
1260
1160
1244
1198
FDE140 type
1470
1370
1454
1408
Models
150 ~ 160
Concrete
25 ~ 45 mm
Ceiling board
Notes (1) In case the susprnsion bracket face in, and the supension
bolts are made to the length as shown in the left drawing
the bolts ends will be put in the plasitics cap of the
indoor unit top panel.
(2) Dont remove the plastics cap.
Suspension bolts
t 10
abou
mm
Front
Rear
871
FDC-HKX
2) In case of exposed installation to the ceiling ( with suspension brackets facing in)
25 ~ 45 mm
Ceiling boards
Suspension bolt [M8~M10 (3/8)]
Suspension bracket (accessory parts)
Flat washer (accessory parts)
Hexagonal nuts (accessory parts)
c) Fix unit securely in place by tightening the suspension bracket fixing bolts.
d) Attach the side panels and installation is finished.
Ceiling
3) In case the unit is half recessed into the ceiling ( the suspension brackets facing outside)
a) Open a hole in the ceiling large enough for the unit and necessary installation work. ( Fill up the excess opening after the
installation work is finished.)
Opening
300 o
more
Unit : mm
61
re
r mo
300 o
10
10
872
FDC-HKX
b) Installation space dimensions
80
(FDE112,140)
Unit upper
side
10
160
10
24
(Plug in dimensions)
(FDE36,45,56,71)
Unit: mm
Ceiling board
10
Suspension bolts
Flat washer (accessory parts)
Hexagonal nuts (accessory parts)
d) Securely tighten the nuts and fix the indoor unit place.
e) Attach the side panels and fit in ceilling board in the space around the unit and the work is finished.
0~3 mm
0~3 mm
873
FDC-HKX
(7) Wall mounted type (FDK)
(a) Selection of installation location
1) Select the best position and direction depending on the shape of room and height of ceiling to ensure that the cooled or warmed
air will be circulated sufficiently.
cooled air throw
Unit : m
200 mm
or more
Item
Models
Air throw
5
5.5
150 mm
or more
200 mm
or more
[Conditions]
a) Fan speed: Hi
b) Location: Free space without obstacles
c) Distance of reach indicates the horizontal distance after the wind touched down the floor.
d) Air yelocity at the throw:0.5 (m/sec.)
2)
Where there is no obstacle around the Air inlet port or Air outlet port.
3)
Where a sufficient space can be reserved for the service of air filter and the attachment/removal of panels.
4)
Places exposed to oil splashes or steam (e.g. kitchens and machine plants ).
Installation and use at such place will incur deteriorations in the performance or corrosion with the heat exchanger or damage
in molded synthetic resin parts.
5)
6)
7)
8)
Place where corrosive gas ( such as sulfurous acid gas ) or inflammable gas ( thinner, gasoline, etc.) is generated or remains.
Installation and use at such places will cause corrosion in the heat exchanger and damage in molded synthetic resin parts.
9)
Wooden wall
Bolt
Mounting
plate
Mounting
plate
Min.
210 mm
2) When installing a mounting plate on the wall, adjust it at level precisely and fix securely. Use the marketed anchor bolts (M6)
Mounting plate
874
FDC-HKX
(c) Installation
1) Use an attached pattern sheet and mark the position of screws to attach the mounting plate.
2) Determine the direction to lead the pipe and bore a through hole on the wall aligning with the pipe hole of unit.
Wall
Indoor
Outdoor
Sealing
plate
Wall
Sleeve
70 mm
Sleeve
Cut the sleeve for the thickness
of wall and insert in the hole.
3)
2
1
Front
slightl to remove.)
5)
875
FDC-HKX
6) Hook and install the indoor unit on the mounting plate
from top. Hook slightly at left at first and return to right.
876
FDC-HKX
(8) Floor standing exposed type (FDFL)
(a) Selection of installation location
1) A place where good air circulation and delivery can be obtained.
Cooled (warmed) air throw
Unit : m
Models
All models
Air throw
[Conditions]
(1) Fan speed: Hi
(2) Location: Free space without obstacles
(3) Distance of reach indicates the horizontal distance after the wind touched down the floor.
(4) Air velocity at the throw: 0.5 (m/sec.)
2)
Where there is no obstacle around the Air inlet port or Air outlet port.
3)
Where a sufficient space can be reserved for the service of air filter and the attachment/removal of panels.
4)
Places exposed to oil splashes or steam (e.g. kitchens and machine plants).
Installation and use at such places will incur deteriorations in the performance or corrosion with the heat exchanger or damage
in molded synthetic resin parts.
5)
6)
7)
8)
Places where corrosive gas (such as sulfurous acid gas) or inflammable gas ( thinner, gasoline, etc.) is generated or remains.
9)
Installation and use at such place will cause corrosion in the heat exchanger and damage in molded synthtic resin parts.
10) Where a sufficient space can be reserved for service.
Floor standing installation
Wall fixation
150 or more
Unit : mm
1000 or more
Floor fixation
150 or more
600 or more
600 or more
Floor
195
205
Front side
Rcar side
806(1091)
1196(1481)
View from the floor
205
unit : mm
195
470
220 250
98
32
10 30 Slotted holes
M8
1196(1481)
786(1071)
12 24
M10
877
FDC-HKX
(c) Installation of unit
1) Floor standing installation
a) Position of mounting bracket fixing bolts Drill holes by referring to figures below.
When fixed on the wall
4 places
Hole for piping &
wiring on wall
30
Wall
2 places
Note (1) Be sure to use a bolt of the length for wall mouning.
Wall
Outdoor
Sealing plate
Sleeve
70~86 mm
Sleeve
Top panel
d) Level the unit using the level adjusting screw. Installation will be complrted after attaching side and front panel.
e) Exceute fixation following the directions described below.
When fixed on the wall
878
FDC-HKX
(d) Drain piping
The drain piping can be directed to the floor or rear sides as follows.
(a) Connect a drain piping to the drain outlet and fix it by use of tigghening band.
(b) Indoor side drain piping must be thermally insulated.
(c) After finishing the drain piping, check the drainage by pouring some water in the drain pan.
Up-and-down bend
Bad
Bad
Trap
Decrine
84
0.5
2-3.0
VIEW A
879
FDC-HKX
4) Wiring route.
a) Wire from the wiring hole through the rear side of the control box to the terminal block.
b) Any suplus wires should be tied up with a cable tie. Remote controller
installation section
Cable tip
Control box
Front Side
Unit : m
Models
All models
Air throw
[Conditions]
2)
3)
4)
5)
6)
7)
8)
9)
unit : mm
Peri cover
1000
600
Floor fixation
Peri cover
100
100
600
Floor
880
FDC-HKX
(b) Bolt positions
1) Bolt positions for metal settings used for floor fixation.
unit : mm
1150(1435)
unit : mm
112
786 (1071)
179
Back
250
220
470
Front
806(1091)
4 places
Hole for piping &
wiring on wall
30 mm
Wall
2 places
Note (1) Be sure to use a bolt of the length for wall mouning.
Wall
Outdoor
Sealing plate
Sleeve
70~86 mm
Sleeve
c) Level the unit using the level adjusting screw. Installation will be complrted after attaching side and front panel.
d) Exceute fixation following the directions described below.
When fixed on the wall
Mounting platc
(Accessory)
881
FDC-HKX
(d) Drain piping
The drain piping can be directed to the floor or rear sides as follows.
(a) Connect a drain piping to the drain outlet and fix it by use of tigghening band.
(b) Indoor side drain piping must be thermally insulated.
(c) After finishing the drain piping, check the drainage by pouring some water in the drain pan.
Up-and-down bend
Bad
Bad
Decrine
19.5.2
Trap
Exposed installation
(a) Remove the remote controller case.
Insert finger nails between the upper (white) and lower
(brown) cases and ply them to open.
Cut the remote controller lower case off at the top and thin
section with a nipper, knife or other and remove burrs from
the cut with a file or other.
(c) Secure the remote controller lower case on the wall with 2
Top
pieces of wood-screws.
Bottom
(d) Connect the remote controller cords with the terminal block.
Make sure to align the terminal numbers on the indoor unit
and the remote controller. Polarities are specified on the terminal block so that the unit will not be operated if the cords
are connected improperly.
Terminals: (X) red wire, (Y) white wire, (Z) black wire
882
FDC-HKX
(e) Set necessary functions in accordance with the model of indoor unit.
Refer to (c) for the setting of functions.
(f ) Couple the upper case with the lower case as they were.
(g) Secure the remote controller cords on the wall or other using cord
clamps.
To indoor unit
Embedded installation
1) Have a JIS box and remote controller cords (use shielding wires or
Upper case
J6
JIS box
(Provided by customer)
Selector switch
(SW1 ~ SW4)
Heat sensor
element
Jumper wire
(J1 ~ J4)
Switch
3) Secure the remote controller body on the JIS box with 2 pieces of M4
round head screw (provided by customer).
SW1
SW2
5) Couple the upper case with the lower case as it was to finish up the
installation.
SW3
Function
C
ON
OFF
ON
OFF
SW4
Name
M4 round head screw x 2 pieces
(Provided by customer)
J1
J2
J3
J4
J6
With
Function
Return air temperature display - Valid
For KX multi
883
FDC-HKX
19.5.3 Installation of outdoor unit
(1) Selection of installation location
(a) A place where air will not be stagnant.
(b) A place where the exhaust air will not be shortcycled.
(c) A place with enough space for air flow around the unit.
(d) A place where the unit will not be affected by other heat sources.
(when there are multiple units installed or when units have another heat source)
(e) A void installing the unit in places that are subject to sea air, sulfureous gas of the type found in hot springs, or any other
corrosive or flammable gas.
(f)
A place where smooth drainage of rain water and water formed by defrosting is acceptable.
(g) In heating operation, snow deposit on the heat-exchanger of outdoor unit must be prevented for keeping the normal
performance capacity.
Snow-hood on outdoor unit as in drawing, will reduce the frequency of defrost operation.
When installing the snow hood, take care so that their outlet of the snow hood will not face directly into the most windy
direction.
Design the base higher than possible snow deposit.
(h) A place where air outlet port is not exposed to strong wind.)
(2) Installation space
A place with enough space for air inlet, air outlet and service space.
(a) Independent installation
1) Standard oblique blow or up blow
2) Side blow
L2
L4
(Service space)
L1
Wall height H2
L3
Wall height H4
Wall height H2
Air inlet
Wall height H1
Installation
example
Dimensions
L1
L2
L3
L4
H1
H2
H3
H4
I
Open
0
300
Open
Not limited
Not limited
-
II
Open
0
300
500
Not limited
Not limited
Not limited
Air inlet
L3
L2
L4
(Service space)
L1
Wall height H1
(Unit : mm)
III
500
0
300
0
1000 or less
Not limited
700 or less
Not limited
Note (1) When the wall heights H1 and H3 exceed the limited value, keep dimensions for L1 and L3 as shown below.
L1 = H1 500 (In the case of side blow, H1 1,000 irrespective of L1 dimension)
L3 = 300 + (H3-700) / 2
However, there is no limitation in wall height H3 if L3 exceeds 600.
884
Wall height H4
Wall height H3
Wall height H3
FDC-HKX
(b) In the case that there is a wall above the unit
No. of units that can be installed are limited up to 3 units.
(Example : 5HP 3 units, 10HP 1 units + 5HP 1 unit)
L1
5 HP
L1 or L2
(One-blower unit)
L1 + L2
500
8 or 10HP
L1 or L2
350
(Two-blower unit)
L1 + L2
750
L2
(c) Plural units installation (Single crosswise row installtion : No limitation in No. of units)
Air inlet
L3
L2
L3
(Service space)
L1
Wall height H4
Wall height H2
Wall height H3
L1
500
H1
1,000
L2
H2
No limitation
L3
300
H3
700
L4
H4
No limitation
Wall height H1
Note (1) When the wall heights H1 and H3 exceed the limited value, keep dimensions for L1 and L3 as shown below.
L1 = H1 500(In the case of side blow, H1 1,000 irrespective of L1 dimension)
L3 = 300 + (H3700) / 2
However, there is no limitation in wall height H3 if L3 exceeds 600.
(d) Plural units installation (Plural installation in lengthwise and crosswise rows)
Notes (1) Side blow is not allowed.
(2) Secure dimensions L1 and H1 at the service space side. Secure dimensions L3 and H3 at the suction side.
Wall height H3
L3
Wall height H2
W1
W2
W3
L4
Wall height H4
L4
L2
L1
500
L2
1,000
L3
300
L4
1,000
H1
1,000
H2
No limitation
H3
700
H4
No limitation
L1
Wall height H1
885
FDC-HKX
(3) When the wall heights H1 and H3 exceed the limited value, keep dimensions for L1 and L3 as shown below.
L1 = H1 500
L3 = 300 + (H3700) / 2
However, there is no limitation in wall height H3 if L3 exceeds 600.
Oblique blow
(standard)
Up blow
(option)
W1
1,500 and
over
W2
800 and
over
W3
1,500 and
over
W4
1,500 and
over
800 and
over
800 and
over
1,500 and
over
1,500 and
over
(4) The space of 1,500 mm per a series of 8 blower units is required for W4.
(Example : 5HP 8units in series installation, 10HP 4 units in series installation)
(5) When installing more than 3 rows with the oblique blow in lengthwise, change the blow direction of the group in the central row units,
excluding the both end rows, to the up blow (option). This group blows to the wall and also opposes to the units at the rear in the suction face.
For the example shown below, the uppermost group in the second row falls under the above notes.
1st row
2nd row
3rd row
(6) Install the rack that stores the piping, etc. so that it does not interfere with the airflow entering into the heat exchanger.
Wind direction
886
FDC-HKX
(c) Securing outdoor unit (in the case of exposure to severe weather conditions)
Fix the unit in the following way.
Use overturning prevention brackets.
Rig with wires.
(Use rigging wires that are resistant to corrosion and sufficient in strengh.
For example SUS304-W1, wire thickness 2.9 mm)
(4) Installation
Fix the unit in a proper way according to the condition of a place where it is installed by referring to the following.
(a) Fix the unit to the foundation with anchor bolts.
FDC140 type
Position of
anchor bolt
(M10 ~ 4 places)
[Service panel side]
unit : mm
Position of
anchor bolt
(M10 4 places)
887
FDC-HKX
19.5.4 Refrigerant piping
(1) Precautions no refrigerant piping work for prevention against compressor lock
Compressor trouble including lock and motor burn-out is due to faulty parts but mainly concerned in installation and refrigerant
piping conditions, The precautions for refrigerant piping are as belows.
(a) Be sure to perform brazing while flowing nitrogen.
1)
Without flowing nitrogen gas, a lot of oxide film (CU2O) is generated. In particular, in case of for building with many brazed
portions, oxide film is so much generated that this causes a fatal failure in the air conditioning system.
2)
A foreign material (oxide film) causes clogging of the capillary tube or expansion valve, leading to non-cooling (nonheating), abnormal discharge temperature, compressor lock due to a faulty oil return. In some cases, a lot of foreign materials
block the oil return hole of the accumulator, thereby causing a compressor lock. (This lock trouble may occur repeatedly 2 or
3 times.)
condensation).
2)
3)
Overcharge
Liquid back
Faulty oil return
(e) Be sure to support the refrigerant piping with support fittings.
Too long (L):
1)
Compressor lock
Compressor lock
The pipe vibrates and expands/shinks during operation. Without proper supports, a load is concentrated partially and cracks
and collapse occur on the piping, thereby causing a unit failure.
2)
888
FDC-HKX
(2) Table for selection of piping size
FDC 140 type
Outdoor unit
Main piping
19.05
9.52
No. 1 branch
19.05
9.52 DIS-2KX20-E
Model
Item
15.88
19.05
9.52
25.4
12.7
28.58
12.7
25.4
12.7
DIS-2KX30-E
DIS-2KX10-E 15.88
DIS-2KX10-E 15.88
9.52
DIS-2KX10-E
12.7
DIS-2KX30-E
DIS-2KX20-E
9.52
19.05
25.4
DIS-2KX20-E 19.05
12.7 DIS-2KX30-E
25.4
DIS-2KX20-E
Notes (1) If adjustment is required between the branch connection and the unit port, always make the adjustment on the branch connection side.
(2) The selection of piping size and branch piping, total all the indoor unit down flow capacity for that piping and branch piping.
12.7
Gas line
118
ID
25.4
19.05
15.88
15.88
ID
12.7
9.52
6.35
ID
28.58
OD
25.4
70
94.5
ID
19.05
15.88
12.7
ID
19.05
70
Liquid line
OD
19.05
ID
25.4
87
ID
9.52
ID
9.52
6.35
ID
15.88
12.7
424
370
Gas line
370
Reducer
Liquid line
87
Liquid line
ID
9.52
12.7
ID
12.7
9.52
ID
19.05
Gas line
519
Gas line
DIS-2KX20-E
Item Mark
Liquid line
DIS-2KX30-E
ID
25.4
28.58
424
Gas line
94.5
ID
15.88
12.7
ID
15.88
Gas line
6
370
Liquid line
87
ID
9.52
ID
9.52
6.35
Liquid line
DIS-2KX10-E
889
FDC-HKX
Example of piping
Outdoor unit: FDCJ280HKXE2B
Indoor unit: Combination of 8 units
[Branch pipe set : DIS-2KX10-E 1 set, DIS-2KX20-EX 3 set, DIS-2KX30-E 3 set]
[Total capacity: 363 (36300W) ]
Selecting piping size
Outdoor unit
FDCJ280
Branch Branch
piping 1 piping 2
Branch
piping 6
Branch
piping 7
G
c
b
a
Indoor unit
56
56
36
36
36
71
36
36
Item
Selection procedure
A
B
C
D
E
F
G
a
b
c
d
e
f
g
h
Selection procedure
Total capacity of the connected indoor units 363
Total capacity of the connected indoor units 251
Total capacity of the connected indoor units 215
Total capacity of the connected indoor units 179
Total capacity of the connected indoor units 143
Total capacity of the connected indoor units 72
Total capacity of the connected indoor units 112
Notes (1) Make the selection based on the size of each piping for branch piping sets with different size connections.
(2) If diameter adjustment is need for branch connection and on the indoor unit side, always makes the adjustment at the
branch connection.
Reference: The shape of the flow divider pipe and reducer is shown on the 889 page.
Pictogram
ID
: Branch pipe
: Reducer
Inner finish
OD
Outer finish
Horizontally
Notes (1) Use the designated piping size for the piping between
the outdoor unit and the first branch.
(2) Choose the appropriate sized reducer for piping between
the branch pipe and the indoor unit.
The size of reducer should match the piping size of the
indoor unit.
(3) Locate the branch pipe horizontally or vertically as
illustrated to the right.
Floor
Good
No
Good
Floor
Vertically
No
Floor
890
FDC-HKX
(3) Specification of unit piping (Pipe diameter, Connecting method)
(a) Unit
1) Outdoor unit
Unit: mm(in)
Item
Model
Gas line
Pipe diameter
FDC140 type
19.05 ( /4 ")
FDC224 type
25.4 (1 ")
FDC280 type
28.58 (1 /8 ")
Liquid line
Connecting method
Pipe diameter
Connecting method
9.52 ( /8 ")
3
Flare
Brazing
Flare
12.7 ( /2 ")
Unit: mm(in)
2) Indoor unit
Item
Model
Gas line
Pipe diameter
Liquid line
Connecting method
Pipe diameter
22, 28 type
36 type
45 type
56,71,90 type
15.88 ( /8 ")
112,140 type
Connecting method
Flare
Flare
For R407C
Outer diameter (mm) Wall thickness (mm) Outer diameter (mm) Wall thickness (mm)
Outer diameter (mm) Wall thickness (mm) Outer diameter (mm) Wall thickness (mm)
6.35
9.52
12.7
15.88
0.8
0.8
1.0
1.0
19.05
25.4
28.58
1.0
1.2
1.4
6.35
9.52
12.7
15.88
0.8
0.8
1.0
1.0
19.05
25.4
28.58
1.2
1.4
1.4
4) Tightening torque
6.35(1/4 ") Flare nut
16 ~ 20 N m (1.6 ~ 2.0 kg m)
40 ~ 50 N m (4 ~ 5 kg m)
40 ~ 50 N m (4 ~ 5 kg m)
90 ~ 120 N m (9 ~ 12 kg m)
891
FDC-HKX
(b) Refrigerant connection piping.
Connection to
left direction
Refrigerant
piping
Electric
wing
Electric
wing
Connection to
front direction
Electric
wing
Refrigerant
piping
Refrigerant
piping
Connection to
rear direction
Connection to
right direction
Connection to
lower direction
(i) There is a need to insulate both gas and liquid piping with heat insulation for protection against heat and
condensation.
1) Always use heat insulation to prevent condensation on the gas piping from becoming drain water and
causing leakage during cooling and to prevent people from being burned by the high temperature of the
surface of the gas piping as discharge gas flows through it.
2) Use heat insulation (pipe cover) on the flare connection sections of the indoor unit.
(Insulate both the gas and liquid piping.)
3) Insulate both the gas and liquid piping. Apply the insulation so that is tight against the piping and free
of gaps. Route the connecting wires with the insulation and wrap the entire bundle with exterior tape.
;;;
;;;
;;;
;;;
;;;
;;;
;;;
;
;;
Exterior tape
Gas lines
Insulation
Use insulation material with good resistance heat properties (120 C or more).
(a) When conducting an air-tight test of local piping, connect the piping to the check joint of the evacuating pipe connected to the
gas side service valve, and keep the service valve closed. The air-tight test pressure shall be 2.94MPa [R407C : 3.23MPa]
(b) To conduct the test, pressurize the check joint of evacuating pipe by nitrogen gas as shown below. The local piping including
indoor units can be tested as for airtightness.
Gas side service valve
Check joint
ss- g
e
r
P zin
uri
Indoor unit
Outdoor unit
892
Indoor unit
FDC-HKX
(6) Evacuating
Evacuating can be completed faster by evacuating both the check joint on the liquid side service valve and the check joint of the
evacuating gas pipe (accessory) connected to the gas side operation valve at the same time. (Of course, evacuating is possible even
through the liquid side check joint only.)
Outdoor unit
Gauge manifold
Open
Open
Close
Close
Vacuum pump
Check joint
Indoor unit
Indoor unit
Indoor unit
12.7
Outdoor unit
9.52
6.35
9.0 kg
FDC140 type
FDC224 type
0.12 kg/m
0.06 kg/m
0.03 kg/m
12.0 kg
Indoor unit
Holding
charged
FDC280 type
Remarks
Additional
refrigeramt
Charge is not
required
Notes (1) When the refrigerant piping length exceeds the length that additional refrigerant charge is not required, charge additional refrigerant based on to
calculated amount of refrigerat per unit piping length.
(2) The unit is holding charge type that all of the refrigerant is charged in the outdoor unit and in the indoor unit only a small amount of refrigerant is filled for
prevention of the air entry.
893
FDC-HKX
19.5.5 Electric wiring
(1) Power supply wiring
(a) Outdoor unit power supply
Use separate power supplies for the outdoor and indoor unit respectively. (Standard specification)
The table below shows the power specification for outdoor unit only.
Item
Power
source
Model
Wire
length
(m)
3.5
FDC140 type
FDC224 type
Circuit breaker
Power
supply
wire size
(mm2)
3 phase
380/415V
50Hz
FDC280 type
Grounding
wire size
(mm2)
Switch
capacity
(A)
Reted
current
(A)
Earth
leakage
breaker
(A)
38
30
25
30A 30mA
0.1 sec. or less
2.0
5.5
46
40
30
40A 100mA
0.1 sec. or less
2.0
8.0
47
60
50
60A 100mA
0.1 sec. or less
3.5
Notes (1) The above table shows the power specification of outdoor unit when separate powers are use for outdoor unit and indoor units.
(2) The wire thickness and distance indicated above are for when voltage drop is 2%.
Item
Wire
length
(m)
Rated
current
Circuit breaker
(Use for both ground/overload
and short-circuit production)
Outdoor
Indoor
Indoor
Outdoor
23
20
10A or more,
less than 15A
3.5
27
30
2 core
x
0.75 2.0
2 core
x
0.75 2.0
Indoor unit
Total power
supply for
indoor unit
Power
supply
wire size
(mm2)
Notes (1) The wire length covers values when necessary indoor units are connected in series with the unit power supply wire as shown below. Also, the wire
thickness and distance indicated above are for when voltage drop is 2%.
(2) These values are based on the conditions that indoor units are connected so that the total capacity becomes the mximum against each outdoor unit.
Earth leakage
breaker
Circuit breaker
r1
894
r2
r4
FDC-HKX
(2) Precaution in electric wiring.
(a) Use separate power supplies for the outdoor and indoor units respectiveliy (Standard specification)
(b) Signal wiring (for indoor and outdoor units)
Double-core cable with a diameter 0.75 to 2 mm2 should be used for the signal wires.
Never make the indoor and outdoor connecting signal line use co-axial cable or strand with the power
wiring for indoor and outdoor unit and other ower line.
(Never use a multiconductor wire together with power line. It may cause erroneous operation.)
Do not connect high voltage wires 220/240 V or 380/415 V to signal wires. as these wires are DC 5V. Signal wires should be
connected so that the terminal Nos. conform with each other for between outdoor and between indoor units. However, they
will work properly if different polarities are connected.
(Connect (A) and (A), (B)and (B).)
Do not strand or run the remote control cord with power line, electric line, etc.
The total length of the signal wires Should be 1000m or less.
Recommended signal wire list
Name
No.
Symbol
Shielding wire
When No. 4 shielding wire is used, always ground the single wire side of the shielding wire . In addition, using the shielding
wire is helpful to prevent the incorrect connection between 5V DC and 220/240V or 380/415V AC because the
discrimination from the power supply wire is clear.
(3) Wiring system Diagram
Model FDC140type
Power source (outdoor unit side)
3phase 380/415V50Hz
Earth leakage
breaker
Outdoor unit
Circuit Breaker
Earth
Signal wire (Between outdoor and indoor units)
Signal wire (Between indoor units)
Circuit breaker
Earth leakage
breaker
Indoor
unit
<I>
<II>
<III>
remote
controller
wire
Remote controller
<IV>
<V>
<VI>
895
FDC-HKX
Models FDC224, 280type
Power source (outdoor unit side)
3phase 380/415V50Hz
Earth leakage
breaker
Outdoor unit
Circuit Breaker
Earth
Signal wire (Between outdoor and indoor units)
Signal wire (Between indoor units)
Circuit breaker
Earth leakage
breaker
Indoor
unit
<I>
remote
controller wire
<II>
<III>
<IV>
<V>
<VI>
<VII>
<VIII>
Remote controller
Power source (indoor unit side)
1phase 220/240V50Hz
A B
L A B
N X Y Z
L A B
N X Y Z
Indoor unit
<I>
Remote controller wire
X Y Z
<II>
Remote
controller
X Y Z
Remote
controller
Signal wire
Do not connect high voltage wire 380/415V to signal wires, as these wires are DC 5V. Signal wires should be connected so that the
terminal Nos. conform with each other for between outdoor and between indoor units. However, they will work properly if different
polarities are connected. (Connect (A) and (A), (B) and (B).)
896
FDC-HKX
(4)
B
Double cores 0.75 ~ 2 mm2
Total length of signal wires: 1000 m or less
Notes (1) The indoor and outdoor signal wiring are without polarity
B
(2) For connection to the terminal block, use as M3.5 (5/32) round eye-let terminal is shown below.
7 mm or less
A maximum of 48 indoor units can be connected by using the crossover wiring method, with 2 wires for
each side of the outdoor and indoor units.
Outdoor unit
Outdoor unit
AB
AB
Outdoor unit
AB
Outdoor unit
AB
AB
Indoor unit
2)
AB
Indoor unit
AB
Indoor unit
Indoor unit
Outdoor
unit
Outdoor
unit
Outdoor
unit
Double cores 0.75 ~ 2 mm2
Total length of signal wires: 1000 m or less
3)
Indoor
unit
Indoor
unit
Indoor
unit
Indoor
unit
Indoor
unit
Indoor
unit
Outdoor
unit
Outdoor
unit
Outdoor
unit
Loop wiring of signal wires is prohibited
Wiring at the Portion indicated by a
dotted line is prohibited.
(No)
Indoor
unit
Indoor
unit
Indoor
unit
Indoor
unit
897
FDC-HKX
(5) Remote controller wiring
(a) Wiring for controlling only one indoor unit.
X
Y
Z
Red White Black
X
Y
Z
Red White Black
Indoor unit
terminal blocks
Remote controller
terminal blocks
Note (1) Cables for the remote controller have polarity. Be sure
to connect terminal blocks with the same numbers. If
mis wiring occurs, E1 is displayed and disables the
unit from operating.
Indoor unit
(Outdoor unit
address No.01)
(Indoor unit
address No.00)
A B
Indoor unit
(Outdoor unit
address No.01)
(Indoor unit
address No.02)
A B
Indoor unit
(Outdoor unit
address No.01)
(Indoor unit
address No.03)
A B
Outdoor unit
Unit address
A B
No.02
Indoor unit
(Outdoor unit
address No.02)
(Indoor unit
address No.04)
A B
Indoor unit
(Outdoor unit
address No.02)
(Indoor unit
address No.05)
A B
Indoor unit
(Outdoor unit
address No.02)
(Indoor unit
address No.006
A B
Remote controller
(c) Settings for main and secondary units when multiple remote controllers are used.
Up to two remote controllers can be used for each indoor
unit (or each group of indoor units).
Remote control signal wire (has
Indoor unit
polarity)
X
Y
Z
1) There are two methods for arranging this. One
Match X Y and Z and connect.
method is to take a remote control connection wire
(3-strand) from the indoor unit for the secondary
remote control. The other method is to use a jumper
wire from the main remote control.
2) Set the remote control switch for the secondary unit (SW4) to
X
Y
Z
X
Y
Z
secondary unit. (It was set to main unit a the factory.)
Note (1) The remote controller sensor setting is only enabled on the main remote controller.
Be sure to position the main remote controller in a location where it can detect
the room temperature.
898
Remote
control
SW4
Main
Remote
control
SW4
Secondary
FDC-HKX
(6) Setting of unit address
Addresses can be set either with the automatic address setting, remote control address setting or manual address setting
depending on the combinations of address switches (see table) of the indoor and outdoor units. Operate the address switches
before turning power on.
Indoor unit
Outdoor unit
Address setting method
Outdoor No.
Outdoor No.
Indoor No.
49
49
49
00 ~ 47
49
49
Manual address
00 ~ 47
00 ~ 47
00 ~ 47
Auto address
SW1, 2 (blue)
SW3, 4 (green)
SW1, 2 (green)
0 1
2 3
4
Order of 10
SW1(SW3)
SW1
(SW3)
order of 10
Order of 10
SW2(SW4)
0 1
9
7 8
2 3
00
01
02 03
04
05
06
07
08 09
10
11
12 13
14
15
16
17
18 19
20
21
22 23
24
25
26
27
28 29
30
31
32 33
34
35
36
37
38 39
40
41
42 43
44
45
46
47
48 49
5 6
Order of 1
Notes (1) Outdoor No. is provided on the outdoor and indoor PCB's and indicates which outdoor unit is connected with
which indoor unit via a refrigerant pipe. Indoor and outdoor units connected with a refrigerant pipe must have
the same No.
(2) Indoor No. is used to identify a particular indoor unit. The No. should never be duplicated.
AB
Indoor unit
AB
Indoor unit
AB
Indoor unit
Remote controller
Remote controller
Remote controller
AB
Indoor unit
899
FDC-HKX
1)
Set the address switch of outdoor unit at 49. (This is set at 49 at shipment from factory.)
2)
Set the address switch of indoor unit at 49. (This is set at 49 at shipment from factory)
3)
Turn power on for the indoor and outdoor units. Addresses are set automatically. (No. in a range of 0 - 7 is set for J140H
or No. in a range of 0 - 11 for J224 and 280H.)
For the auto address setting, power must be ON for both the indoor and outdoor units. If power is supplied to the indoor
unit only, "Outdoor No." is indicated on the remote controller. In such occasion, turn power ON also for the outdoor unit.
4)
No. will be set within approx. 1 minute after turning power on.
5)
If you press the inspection switch of the remote controller after setting the No., the address of indoor unit will be displayed.
The outdoor unit No. 49 will also be displayed.
6)
Auto address setting is allowed also when controlling plural number of units with single remote controller. However, the
connection cannot be made across different refrigeration lines.
Information 1) Once addresses are set, they are retained on the microcomputer even after turning power off.
2) Even if the wiring is arranged on the basis of outdoor units, (2) remote control address setting and (3) manual
address setting can be used.
Outdoor unit
Outdoor unit
No.00
No.01
AB
Indoor unit
Indoor unit
AB
Indoor unit
Indoor unit
Remote controller
Indoor unit
Indoor unit
AB
900
AB
Remote controller
Remote controller
Remote controller
Remote controller
1)
2)
3)
4)
AB
AB
Remote controller
Set the address of outdoor unit with a number in a range of 0 - 47 avoiding duplication with any other outdoor unit.
Leave intact the address switch on the indoor unit PCB at 49 as set at the shipment from factory.
Turn power on. Then you can proceed the remote control address setting.
Set the outdoor No. corresponding to each indoor unit, using the remote controller. Set next the indoor No. of indoor unit
in a range or 0 - 47 avoiding duplication with any other unit connected in the group.
FDC-HKX
If the power switch is turned on, the outdoor No. on the display flashes, and "--" on the return air temperature display
section and "U--" on the time display section are lit.
If power is not supplied to the outdoor unit, the outdoor No. only lights and you cannot set the address. In such occasion,
to turn power on also for the outdoor unit.
2)
Indoor No. increases 0, 1, 2, ... and up at each push on the room temperature setting switch. Press the room temperature
setting to reduce the outdoor No. 0, 47, 46, 45 ... and down. Stop to press the switches when a desired No. is indicated.
3)
Press the Set switch so that the outdoor unit display changes from flashing to firm lighting and the outdoor No. is set.
Simultaneously, "U" indicating the indoor unit No. starts to flash.
4)
5)
Set the indoor No. in the same way with the room temperature setting switches and .
After completing the setting, press the Set switch so that the "U" display changes from flashing to firm lighting and the
6)
7)
This is all for the address setting. The address display will go off 5 seconds later.
Note (1) Once the addresses are set, they are retained on the microcomputer even after turning power off. If you need to
Address No.
by address switch
Outdoor unit
Outdoor unit
No.01
No.02
AB
AB
Indoor unit
Indoor unit
AB
AB
Indoor unit
Indoor unit
AB
AB
Indoor unit
Indoor unit
Remote controller
AB
AB
Remote controller
901
FDC-HKX
(7)
1)
Using the address switch (green) on the outdoor unit PCB, set the address of the outdoor unit in a range of 00 - 47 avoiding
duplication with any other outdoor unit.
2)
Using the address switch (green) on the indoor unit PCB, set the outdoor No. at the same No. as the outdoor unit which is
connected with a refrigerant pipe.
3)
Using the address switch (blue), set the indoor No. of indoor unit in a range of 00 - 47 avoiding duplication with any other
unit on the connection.
Change of control
Details of control for outdoor units are selectable with the methods as listed below.
Selecting method of control
902
FDC-HKX
19.5.6 Test run
(1) Before starting operation
(a) Measure resistances between the electrical parts terminal blook and ground grounded area using a 500V Megger, insulator.
Resistance must be higher than 1M .
(b) Confirm whether the power source breaker (main switch) of the unit has been turned on for over 12 hours
to energize the crankcase heater in advance of operation.
(c) Make sure that the compressor bottom has been warmed.
(d) Be sure to fully open the service valves (on both the gas and liquid sides) of the outdoor unit. if being
operated without opening, the valve may be got out of order.
Note (1) When the service valve is closed, be sure to check that evacuation is completed or a refrigerant is charged.
Normal (OFF)
No.6 of [SW3]
[Remark]
This operation has priority over other option commands with the center console.
At the time of trial operation, the maximum frequencies are follows. Protective devices are effectively controlled, and frequencies are controlled to become smaller.
(3) Cooling test run operation (Cooling test run can be performed in winter.)
(a) Operating method
In the normal cooling mode, while holding down the Temperature set switch, press the Set switch.
Setting temperature is changed at 5C and the cooling test run is operated for 30 minutes.
It stops after 30 minutes.
(b) During cooling test run operation
If ON/OFF switch is pressed or a mode other than the cooling is selected by the Mode switch, the cooling test run
operation is released or returns to the specified operation mode.
If the Temperature set switch is pressed, the setting temperature changed at 18C and the cooling test run operation is
released but the cooling operation continues.
It is effective when any switches other than the above are pressed.
(c) During the cooling test run operation, the setting temperature changes at 5C but any other control and protective functions are
operable just like in the normal operation.
If any error occurs, the location of error is indicated on the remote controller display or with the condition of flashing of
inspection lamp (red) on the main unit controller. Remove the cause of trouble before starting operation again.
(4) Delivery
(a) Explain how to operate the indoor unit to your customer according to the accessory owners manual.
(b) Persuade the customer not to turn off the power switch even if the unit is not used for along time. The air
conditioner can start operation any time when your customer want to heating or cooling his room. (The
bottom of the compressor is heated with the crank case heater, and compressor troubles can be prevented when the cooling or heating season sets in.)
903
FDC-HKX
19.6 MAINTENANCE DATA
(1) Before starting troubleshooting
(a) Confirmation of the error code on the remote controller (by pressing the inspection switch) and the inspection display and normal display lamps on PCBs (Printed circuit board) of indoor/outldoor units
The microcomputer detects errors on electrical components, which include the microcomputer itself, errors on the power supply
line and errors (overload, etc.) on the refrigerant circuit and the location of trouble is displayed (with the commbination of error
symbols of remote controller, normal (green) and inspection (red) display LED on PCBs of indoor/outdoor units). When any error
occurs, check first the inspection display. It will guide you to trouble point and assist you to complete the repair work quickly.
Error code of the remote controller is recorded on microcomputer after the trouble has been reset automatically so that, if you press
the inspection switch of remote controller, the error code and the number of unit in trouble are displayed for 10sec.. The inspection
display lamp on the indoor/outdoor unit PCB keeps flashing (glowing) even after the trouble was reset automatically. Inspection
lamp on the indoor unit PCB is turned off if the remote controller is reset.
1)
Remote
controller
Section
Display Section
Display
Contents of display
LCD
Error code
LCD
Indoor/outdoor
unit
Inspection display
Normal display
Error display
Normaly display
Red-LED
Green-LED
Red-LED
Green-LED1
At error : Flash 1 ~ 9 times/10 sec for outdoor unit depending on the kinds of
error, continuous flash, irregular illumination or off.
At power ON (normal) : Flash continuously.
At error : Off or continuous glowing or irregular illumination.
Invertes
1 time flash
904
Error display
Red-LED2
Stays OFF
Keeps flashing
E11
Keeps flashing
Keeps flashing
2 time flash
Keeps flashing
Stays OFF
Stays OFF
2 time flash
Keeps flashing
Keeps flashing
Keeps flashing
2 time flash
Keeps flashing
E10
Stay OFF
2 time flash
Keeps flashing
1 time flash
1 time flash
1 time flash
Keeps flashing
2 time flash
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Stays OFF
Stays OFF or Lights
continuously
Stays OFF
Stays OFF
Stays OFF
Stays OFF
2 time flash
Keeps flashing
Stays OFF
Stays OFF
Stays OFF
Stay OFF
Stays OFF
Stays OFF
Keeps flashing
1 time flash
Stays OFF
Stays OFF
Remote control addresses have been set while more than one units of remote
controller are connected.
Indoor / outdoor transmission error. Wire A and B swapping after power ON.
Outdoor power unit failure (when the indoor power supply is different from the
outdoor one).
The corresponding outdoor unit address No. is not found. (Detected only during
operation)
No. duplication at indoor unit addressing. More than 49 indoor unit are connected.
The PAC remote controller is connected to the KX. The remote controller wire Y is
open. The remote controller wires X and Y are reversely connected. (The LED
flash twice a second.) Two remote controllers are provided. *For wire breaking at
power ON, the LED is OFF.
The remote controller wires are connected to A and B on the terminal block.
The indoor/outdoor signal wire are connected in loop form. The indoor unit microcomputer runs away.
Stays OFF
Stays OFF
Remote controller wires X and Y are reversely connected. *For wire breaking at
power ON, the LED is OFF. Remote controller wire is open. (X wire breaking : A
beep is produced and no indication is made. Z wire breaking : No beep and no
indication) The remote controller wires Y and Z are reversely connected.
Normal
Power OFF, T phase wiring is open, power source failure
Cause
Stays OFF
Keeps flashing
3 time flash
Keeps flashing
Keeps flashing
(1 )
Keeps flashing
Stays OFF
Keeps flashing
Keeps flashing
Keeps flashing
*3 time flash
Stays OFF
Stays OFF
Keeps flashing
Stays OFF
Stays OFF
Stays OFF
Keeps flashing
Stays OFF
Keeps flashing
Red
Red
Green
E6
E7
E9
E5
E3
E2
E1
No-indication
Remote
controller
error code
Whether a failure exists or not on the indoor unit and outdoor unit can be know by the contents of remote controller eroor code, indoor/outdoor unit green LED (power pilot lamp and
2)
FDC-HKX
905
906
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Stays OFF
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
Keeps flashing
E30
E31
E32
E33
E34
E36
E37
E38
E39
E40
E41
E42
E43
E45
E46
Keeps flashing
Keeps flashing
Stays OFF
1 time flash
1 time flash
1 time flash
1 time flash
1 time flash
1 time flash
1 time flash
63H1 operation
1 time flash
1 time flash
1 time flash
(2)
1 time flash
(2)
1 time flash
(2)
Indoor No,
48, 49
0 ~ 47
Outdoor No,
0 ~ 47
48, 49
(2)
1 time flash
1 time flash
1 time flash
Cause
Address No. combination error or addressing is performed with the following
combinations.
(2) When plural numbers of compressor and discharge sensor are installed, single flashing of outdoor unit LED (red) indicates CM1
Keeps flashing
Stays OFF
Keeps flashing
E28
Stays OFF
Keeps flashing
1 time flash
Keeps flashing
E12
Red
Green
Red
Green
Remote
controller
error code
FDC-HKX
FDC-HKX
3) Display sequence of error, inspection display lamp
a) One kind error
Display corresponding to the error is shown.
b) More than one errors.
Section
Display section
Displays the error of higher priority (When plural errors are persisting)
E E E E E E E E E E
Error code
E
E
E
E
Resetting was performed at the rate of 1 time per second. An abnormal stop
occured 32-sec time flash.
A check was made once every 20 second. An abnormal stop occured 7 time
running.
After a compressor ON command, this failure was detected for 5 second in
the period of 2 minutes to 2 minutes and 20 seconds.
This failure was detected continuously for 5 seconds.
At the thermostat ON state, an abnormal stop occured immediately after the
float swicth operated.
- At a stop or the thermostat OFF state, the condensate motor was turned on
for 3 minutes after the float switch operated.
After that, an abnormal stop occurred when the float switch operated in 10
seconds.
Error code
When CM1 is on and there is L3-phase current of 0.5 A or less for 10 continuous seconds.
When the CM2 L3-phase current is 2 A or less for 5 continuous sections after CM2 has
gone on.
A stop occurs when this abnormality occurs for 2 seconds running at 130C.
After a stop for 3 minutes, an recovery is automatically made.
An abnormal stop occurs when this abnormality occurs twice for 60 minutes.
(The abnormal state is held for 45 minutes.)
E
E
This failure is detected when it occurs for 5 seconds running in the period of 2
minutes to 2 minutes and 20 seconds with the compressor ON. An abnormal stop
occurs when this failure occurs 3 times for 40 minutes.
This failure is detected when it occurs for 5 seconds running in the period of 10
minutes to 10 minutes and 20 seconds with the compressor ON. An abnormal
stop occurs when this failure occurs 3 times for 40 minutes.
E
E
E
E
An abnormal stop occurs when this abnormality occurs 2 times for 40 minutes.
A stop occurs at 118C or more. After 3 minutes, a recovery was automatically
made at 100C or less. Abnormal stop occurs when this abnormality occurs 2
times for 2 hours.
An abnormal stop occurs when this abnormality occurs 4 times for 15 minutes.
This error is detected when the number of connectable units is set over the
specified value at remote control addressing.
When an transmission error continues for 10 seconds, the 52C is turned off. With
a delay of 3 minutes, a recovery is automatically made. An abnormal stop occurs
when this errors occurs 4 times for 15 minutes.
907
FDC-HKX
d)
Memory
Reset
Error code
Notes
(1) Priority is in the order of E1 > ... > E10 > ... > 45.
(2) Reset is disabled for 45min. at the error of outdoor unit or compressor overcurrent or the discharge gas temperature error.
e)
Reset of error code in memory (when the error has been reset.)
Indoor unit: Press the Timer switch and the Stop switch while the Inspection switch of wired remote controller is held down
or detach the power supply connector (CnW2) of indoor unit PCB and connect again or turn OFF the power.
Outdoor unit: Detach the power supply connector (CNA2) of outdoor unit PCB and connect again or turn OFF the power
supply or turn on and off the SW3-1.
4)
Indication data
Inverter operation frequency or error code
Description
Normally frequency (Hz) is indicated.
When it is abnormal E?? is indicated.
[L] is indicated when the temperature is -26C or below and the actual
temperature is indicated when it is higher than -26C and up to 73C.
[L] is indicated when the temperature is -21C or below and the actual
temperature is indicated when it is higher than -21C and up to 43C.
[L] is indicated when the temperature is 6C or below and the actual
temperature is indicated when it is higher than 6C and up to 80C.
[L] is indicated when the temperature is 30C or below and the actual
temperature is indicated when it is higher than 30C and up to 136C.
[L] is indicated when the temperature is 30C or below and the actual
temperature is indicated when it is higher than 30C and up to 136C. No
indication for 140 type.
Outdoor temperature
CT (CM1) current
Indicates 0 to 47A.
7
8
CT (CM2) current
SV1
0 : OFF
1 : ON
SV2
0 : OFF
10
63H1
0 : Close
1 : Open
11
63H2
0 : Open
1 : Close
13
Indicates 0 to 16 units.
14
15
Indicates 0 ~ 14 orderly
Error
Check of unit
controller
Note (1) It means the operation to turn off the power and back on again more than 1 min. later in order to reset the malfunction of microcomputer due to the
effect of power supply conditions or accidental noise.
908
FDC-HKX
(a) Diagnosis by the power supply reset
When any error occurs, reset the power supply as described below to see if it is the result of accidental noise, etc.
Check at the indoor unit side.
Error
YES
Is any errror
code display
?
NO
YES
NO
ON/OFF
switch OFF
NO
Microcomputer
out of control
YES
Turn off the wiring breaker (power
supply) and back on again 1min.later.
ON/OFF
switch OFF
NO
YES
NO
YES
Check of error code
909
FDC-HKX
(2) Reference
Effect of noise
Interisified shielding
of control section
Signal wire
l2
Shut off electrically
the noise source or put
it in a shield room.
Cutting machine
welder High
frequency
Outdoor
unit
Make a positive
ground
l1
Remote controller
(indoor unit)
Power
cable
Distribution
board
Beware of noises
transmitted via air.
910
FDC-HKX
Function of jumper wires
Transformer
primary side
Model selector
switch
Control selection
Transformer
secondary side
Power supply
connector for PCB
Name
With
None (1)
With
J2
None (1)
J1
J3
J4
J5
J6 (2)
J6 (2)
J7
J8
Return air
Outdoor unit number
HA connector
thermistor
address switch
Heat exchanger Indoor and outdoor
Limit switch input
Indoor unit number
unit transmission
thermistor
for the auto swing
address switch
With
None (1)
With
None (1)
With
None (1)
With
None (1)
With
None (1)
With
None (1)
With
Function
Setting of 4 position angle of louver
Setting of 4 position angle of louver
4 position louver control : Valid
4 position louver control : Invalid
Heating thermostat OFF - Intermittent
operation
Heating thermostat OFF - Stop
Filter sign : Valid
Filter sign : Invalid
Normal operation operable
Operation permission prohibited
Expansion valve aperture - Fixed at
current aperture.
Expansion valve aperture - Fixed at
new aperture.
Automatic detection of expansion valve
aperture opening (only for J71, 90)
Expansion valve aperture - Fixed at
new aperture.(except J71, 90)
Expansion valve aperture - Normal
Impossibility
Spare
Model
PJA505A073ZA
PJA505A074ZA
FDT, FDTW
Model
Switch
22
28
36
45
56
71
90
112
140
Switch
SW6-1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW6-2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
SW6-3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
SW6-4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
SW5-1
SW5-2
SW5-3
ON
OFF
ON
OFF
ON
OFF
Input
Signal
Function
Reference page
Reverse Invalid
Rus stop
837
832
835
911
FDC-HKX
1
Indoor unit
Outdoor unit
Red LED
Stays OFF
Red LED
Stays OFF
Green LED
Lights continuously
Green LED
Lights continuously
When the LCD display (Center/Remote, temperature display, etc.) of remote controller flashes, it means the polarity on the
unit is not yet determined. Polarity determination is completed within a few seconds after the power on. If it is not completed
in time, CPU out of cotnrol, etc. is suspected.
YES
(2) The unit which has its indoor and green LED lighting continuously (or no lighting) is the one with a
defective indoor unit PCB.
NO
Is it more than
10 sec.
after power on?
YES
YES
If yes, it is a
malfunction by
electrical noise
(1)
Multiple units
on network
(3)
912
(2) (3)
FDC-HKX
Error display : No display
LCD display : No display
Outdoor unit
Red LED
Stays OFF
Green LED
Stays OFF
Unit is normal
(Malfunction by noisse)
YES
Indoor unit
Red
LED
Stays
OFF
Green
LED
Stays
OFF
YES
NO
Indoor unit
Red LED
*3 time flash
(During unit operation)
Green LED
Keeps flashing
Error display
e1
YES
Is it
normalized
Power supply
reset
NO
NO
Indoor/outdoor unit
transfomer CNW2 (indoor).
CNA2 (outdoor). Is AC 17V
checked between (blue)
(blue) and AC 8V between
(red) ~ (red)?
Is there
DC 10V checked
between X (red) ~ Z (black)
of indoor unit terminal
block?
NO
YES
Is the
remote controller
covering multiple
units?
YES
NO
YES
NO
Is it
normalized
Is the power ON
on all indoor units?
Power supply ON
YES
Unit is normal.
(Malfunction by accidental
noise)
NO
Defectve indoor unit
PCB Replacement
913
FDC-HKX
Red LED
Green LED
Indoor unit
*3 times flash
Keeps flashing
Red LED
Green LED
Outdoor unit
Stays OFF
Keeps flashing
Unit is normal.
(Interference by temporary
noise on remote controller
cords)
YES
YES
YES
Is voltage swinging
YES
at DC6 ~ 10V between
indoor PCB connestors (CNK)
2(white) ~
3(black)?
Is it
normalized?
NO
NO
NO
NO
Broken or poor connection of remote controller
cord (white) or (black)
YES
Note (1) If it is normalized by replacing the PCB, it should be judged the remote
controller or indoor unit PCB is defective (defective remote controller
communication circuit).
NO
Defective indoor unit
PCB
Outdoor unit
Indoor unit
Red LED
Red LED
Green LED
Green LED
Stays OFF
Keeps flashing
Is it normalized?
NO
Defective indoor unit PCB
Replace. (Defective CPU)
914
YES
Unit is normal.
(Runaway of indoor unit
CPU due to noise, etc.
Transient trouble)
FDC-HKX
4
Error display
e2
[Duplicated indoor unit No. or More than 49 indoor unit are connected.]
Indoor unit
1 time flash
Keeps flashing
Red LED
Green LED
Red LED
Green LED
Outdoor unit
Stays OFF
Keeps flashing
(1)
YES
NO
(2)
Notes (1) When correcting the unit number, check again the pairing of indoor/
outdoor units (same Number assigned to coupled units) is correct.
(2) If it is normalized by changing PCB, judge the unit number input
circuit is defective.
Error display
Red LED
Green LED
e6
Indoor unit
1 time flash
Keeps flashing
Red LED
Green LED
Outdoor unit
Stays OFF
Keeps flashing
Resistance (k)
YES
Is the indoor
unit heat exchanger
thermistor connector
connection OK?
Are characteristics
of indoor unit heat
exchanger thermistor OK
or is there any
broken wire?
YES
15
10
5k at 25C
NO
NO
Correction
10 20 30 40
Temperature (C)
Note (1) 22.5 k at -6C
Error display
Red LED
Green LED
e7
50
Indoor unit
1 time flash
Keeps flashing
Red LED
Green LED
YES
Outdoor unit
Stays OFF
Keeps flashing
YES
NO
Defective return air
thermistor Replacement
915
FDC-HKX
7
Error display
e9
[Drain trouble]
Indoor unit
1 time flash
Keeps flashing
Red LED
Green LED
Red LED
Green LED
Outdoor unit
Stays OFF
Keeps flashing
YES
Is there any
overflow?
YES
NO
NO
YES
Is the float
switch tripped?
Repair
YES
NO
Defective indoor unit PCB
Replacement (Defective DM
driving output circuit, defective
float switch input circuit)
Remark (1) If an indoor unit is stopped due to the drain error (E9), the outdoor unit fot this stopped unit will come to a normal stop immediately. Other normal indoor units of
the same refrigerant system will also come to a normal stop. Even if the swiches of remote controllers for normal indoor units are pressed, these units will come to
normal stop automatically within tens of seconds.
Error display :
Red LED
Green LED
e10
Indoor unit
Stays OFF
Keeps flashing
Are more
than 17 units connected
to a remote
controller?
Red LED
Green LED
YES
Outdoor unit
Stays OFF
Keeps flashing
Reduce to 16 units
or less
NO
Defective indoor unit PCB
Replacement
Error display :
Red LED
Green LED
Remote control addresses have been set while more than one units of remote
controller are connected.
e11
Indoor unit
Stays OFF
Keeps flashing
NO
Defective indoor unit PCB
Replacement
(Defective unit numer input circuit)
916
Red LED
Green LED
YES
Outdoor unit
Stays OFF
Keeps flashing
FDC-HKX
10
Error display :
Red LED
Green LED
e12
Indoor unit
1 time flash
Keeps flashing
Red LED
Green LED
YES
Outdoor unit
Stays OFF
Keeps flashing
Unit number
correction
NO
Note (1)
Outdoor unit
address No.
00 ~ 47
48, 49
11
Error display :
Red LED
Green LED
e28
Indoor unit
address No.
48, 49
00 ~ 47
Indoor unit
Stays OFF
Keeps flashing
Outdoor unit
Stays OFF
Keeps flashing
Red LED
Green LED
(1)
YES
Are characteristics of
remote controller thermistor OK or is there any
broken wire?
NO
Correction
YES
NO
Detective remote controller
thermistor
Replacement
917
FDC-HKX
(ii) Parts layout on the outdoor unit PCB
Function of DIP switch
Name
7-segement indicator
SW3-1
LED (green)
SW3-2
SW3-3
SW3-4
SW3-5
SW3-6
SW3-7
SW3-8
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Function
Signal line
(Indoor unit)
Name
J1
J5
Outdoor temp.
J6
Under-domo
Outdoor unit
Failure
Operation
number address
output
setting switch
Outdoor unit
Heat exchanger (SW:Order or 10) number address
thermistor
setting switch
(SW:Order of 1)
Discharge
gas thermistor
With
None (1)
With
None (1)
With
None (1)
Function
Jumper
J2
J3
J4
wire
Model
None (1)
None (1)
FDCJ140HKXE2B
With
None (1)
With
FDCJ224HKXE2B
With
With
FDCJ280HKXE2B
(1)
(1)
None
None
FDCP140HKXE2B
None (1)
None (1)
With
FDCP224HKXE2B
With
With
FDCP280HKXE2B
Note (1) "None" means that jumper wire is not provided on the PCB
or the connection is cut.
918
Parts No.
Model
PCB505A026BN
All models
FDC-HKX
(iv) Check procedure depending on indication lamps (For the outdoor unit)
Error display :
e3
2 time flash
Green LED
Keeps flashing
Outdoor unit
Red LED
Stays OFF
Green LED
Stays OFF
YES
Power supply
check between R ~ N or
terminal block
NO
Is there
AC 17V checked
between CNA2 (blue) ~ (blue)
and AC 8V between (red)
~(red) of outdoor unit
transfomer?
YES
YES
Is it
Nomalized?
Power supply
reset
Unit is normal
NO
NO
Defective outdoor
unit PCB
Outdoor unit
Red LED
Stays OFF
Green LED
Is the connection
of network signal
wires good?
YES
Is the paining of
Indoor/outdoor units OK?
Keeps flashing
NO (1)
NO
Error display :
e3
Stays OFF
Power supply
reset
Its it
normalized?
YES
Unit is normal.
(Malfunction by noise)
Keeps flashing
NO
Defective outdoor unit
PCB Replacement
(Defective network communication circuit)
919
FDC-HKX
2
Error display :
Red LED
Green LED
e5
Indoor unit
2 time flash
Keeps flashing
(1)
Outdoor unit
Stays OFF
Red LED
Stays OFF
Green LED
YES
Power supply
ON
NO
Blown fuse?
Broken or loose wire at L1, L2 or
N Phase?
Was not there the power failure?
Note (1) This case is limited to the separate power supplies to indoor/outdoor units. (Combination of (indoor unit) red LED 2 time flash and (outdoor unit) green LED stays off
means that the power supply to the outdoor unit has been interrupted during operation.)
Outdoor unit
Red LED
Stays OFF or
Keeps flashing
Green LED
Stays OFF or
Lights continuously
Is it
normalized
NO
Defective outdoor unit
PCB
Replacement
(Defective network
communication circuit)
Red LED
Green LED
Outdoor unit
Stays OFF
Keeps flashing
(1)
Signal wire
poor connection at
outdoor
unit?
YES
Repair
NO
(2)
Signal wire
poor contact between
indoor/outdoor
unit?
YES
Repair
NO
Power supply reset
Is it
normalized
Notes (1) Check for poor connection (looseness, misconnection) at outdoor unit terminal block and droken signal wires between outdoor units.
(2) Check the poor connection or broken signal wires between indoor/outdoor units.
920
YES
Unit is normal.
(Malfunction by
accidental noise)
FDC-HKX
3
Error display :
Red LED
Green LED
e30
Indoor unit
Stays OFF
Keeps flashing
Outdoor unit
1 time flash
Keeps flashing
Red LED
Green LED
NO
Repair
YES
Defective outdoor unit PCB
Replacement
Error display :
Red LED
Green LED
e3 1
Indoor unit
Stays OFF
Keeps flashing
Is the unit
No. duplicated on
outdoor units?
Red LED
Green LED
YES
Outdoor unit
1 time flash
Keeps flashing
Correction
NO
Error display :
Red LED
Green LED
e32
Note (1) When the PCB is defective, the flash patterns of outdoor
unit red LED, green LED may become irregular.
[Antiphase on power supply or open 52C L3 phase (primary side) on power supply]
Indoor unit
Stays OFF
Keeps flashing
Is there antiphase on
power supply?
Red LED
Green LED
YES
Outdoor unit
1 time flash
Keeps flashing
Note (1) Wrong wire connection of the antiphase
detection circuit is suspected occured
during replacement of the outdoor unit
PCB. Replacement work should be performed carefully.
Correction
NO
(1)
Is L3 phase open at
52C primary side?
YES
Correction
Is antiphase detection
circuit wired properly?
YES
NO
Defective outdoor unit PCB
(Defective antiphase detection
circuit)
Replace
Correction
921
FDC-HKX
6
Error display :
Red LED
Green LED
e33
Indoor unit
Stays OFF
Keeps flashing
Red LED
Green LED
Outdoor unit
1 time flash (1)
Keeps flashing
Note (1) Single flashing of outdoor unit LED indicates CM1 and double flashing indicates CM2.
Defective 52C
Broken wire on L1 or L2
phase between 52C ~ CM or
TB1 ~ 52C
NO
Open L1 or L2 phase
YES
(1)
YES
Is there overcurrent
on compressor?
NO
Defective compressor
Replace.
Error display :
Red LED
Green LED
e34
Indoor unit
Stays OFF
Keeps flashing
Red LED
Green LED
Outdoor unit
1 time flash (1)
Keeps flashing
Note (1) Single flashing of outdoor unit LED indicates CM1 and double flashing indicates CM2.
YES
Notes (1) When voltage is detected at 52C primary side but not at the
secondary side, check also 52C (broken coil, poor contact).
(2) When voltage is detected at 52C primary side L3 phase and
there is no error at 52C, the outdoor unit PCB (defective
52X01 circuit or 52X01 ) or indoor unit PCB (defective
thermostat circuit) is defective.
Repair
NO
(2)
Error display :
Red LED
Green LED
e36
Indoor unit
Stays OFF
Keeps flashing
Red LED
Green LED
Outdoor unit
1 time flash (1)
Keeps flashing
Note (1) Single flashing of outdoor unit LED indicates Th0-1 and double flashing indicates Th0-2.
Is the
discharge gas thermistror characteristics
normal?
YES
Discharge gas
temperature error?
(At cooling/heating
operation)
NO
Discharge pipe thermistor replacement
Is the unit
normalized
NO
Defective outdoor unit
PCB
Replacement
(Defective discharge gas
thermistor input circuit)
922
Error stop
Operable
90C 130C
Discharge pipe temp.
FDC-HKX
Error display :
Red LED
Green LED
e37
Indoor unit
Stays OFF
Keeps flashing
Is the outdoor
unit heat exchanger
themistor connector
OK?
Outdoor unit
1 time flash
Keeps flashing
Red LED
Green LED
YES
NO
YES
NO
Defective outdoor unit
heat exchanger thermistor
Replacement
15
Resistance(k)
Repair
10
5k at 25C
Error display :
Red LED
Green LED
e38
Indoor unit
Stays OFF
Keeps flashing
Is the outdoor
air temperature thermistor
connector connection
OK?
NO
Repair
20 30 40
Temperature (C)
50
YES
Red LED
Green LED
Outdoor unit
1 time flash
Keeps flashing
Is the outdoor
temperature thermistor
characteristics OK, is there
no broken wire?
YES
NO
Defective outdoor temperature thermistor
Replacement
400
Thermistor resistance (k)[T<0C]
10
10
Temperature-resistance
characteristics of outdoor
temperature thermistor (ThO-A)
300
200
40
30
20
T < 0C
T > 0C
100
0
---50
10
0
50
Temperature [T](C)
923
FDC-HKX
11
Error display :
Red LED
Green LED
e39
Indoor unit
Stays OFF
Keeps flashing
Outdoor unit
1 time flash (1)
Keeps flashing
Red LED
Green LED
Note (1) Single flashing of outdoor unit LED indicates Th0-1 and double flashing
indicates Th0-2.
YES
NO
YES
Temperature-resistance
characteristics of discharge
gas thermistor (ThO-D)
Repair
NO
100
10
T< 80C
T> 80C
50
0
0
0
20
50
80
100 120
12
Error display :
Red LED
Green LED
e40
[63H, motion]
Indoor unit
Stays OFF
Keeps flashing
Red LED
Green LED
Outdoor unit
1 time flash
Keeps flashing
At 63H1 operation
Did 63H1,operate?
NO
Defective outdoor unit PCB
Replacement (Defective 63H1,
input circuit)
YES
1. During cooling
Is the outdoor unit fan motor operating?
Is there no short circuit air circulation for thr outdoor
unit?
Is there sufficient space for air inlet & outlet?
2. During heating
Is the gas side service valce fully opened?
Is the indoor unit heat exchanger sensor detached
from the detector case?
Is the filter clogged?
Is the outdoor unit fan controlled by due to defective
63H2?
3. During colling/heating
Is the refrigerant charge excessive?
Note (1) When the wire of 63H1 is broken from the moment of power on, the error E40 is displayed 40 minutes later.
If the operation is started in this period of time, the operation changes to the thermostat OFF state during cooling, and cool
wind blow stops during heating operation.
924
Is the
discharge gas thermistor
connector connection
OK?
FDC-HKX
13
Error display :
Red LED
Green LED
e4 1
Indoor unit
Stays OFF
Keeps flashing
Red LED
Green LED
Does
the
FMO
rotate?
Power transistor
overheating(1)
Outdoor unit
1 time flash
Keeps flashing
YES
Is the
outdoor unit
installation
space
proper?
NO
YES
Does the
IM (Inverter
cooling fan)
rotate?
NO
Defective
inverter
YES
NO
Repair
Note (1) The LD2 on the inverter control PCB lights for 3 minutes. Fin thermostat set value : 118C open
14
Error display :
Red LED
Green LED
e42
Indoor unit
Stays OFF
Keeps flashing
Red LED
Green LED
Outdoor unit
1 time flash
Keeps flashing
Remarks : When current-cut occurs immediately after start (the Hz value does not increase), check the LD3 on the inverter PCB if an error code is not indicated
on the remote controller and the compressor does not operate. When this LD3 is ON, see the next page.
Is the current
(U,V,W) of the
compressor at the
normal level?
YES
NO
Is the power supply voltage correct
(not too hight)?
Are the power supply wires
oppropriate (not too thin)?
Is not it operated under
overload
YES
Power supply
reset
NO
Defective
inverter
YES
Unit is normal
(Malfunction by
accidental noise)
925
FDC-HKX
Current cut is indicated and the compressor cannot operate
Is the insullation
resistance of the compressor(1)
proper?
YES
Defective inverter
(Refer to 933 page)
NO
Is the output
voltage of the inverter
normal?
Defective compressor
YES
Is the current
cut function activated?
NO
NO
Defective inverter
(Refer to 933 page)
YES
When the compressor wiring is
performed, the unit can operate.
YES
Defective compressor
NO
Defective inverter
Unit : V (AC)
Frequency
35Hz
Model
All models
(outdoor unit)
926
160 ~ 180
40Hz
65Hz
75Hz
95Hz
380 ~ 410
FDC-HKX
15
Red LED
Green LED
Indoor unit
Stays OFF
Keeps flashing
Outdoor unit
1 time flash
Keeps flashing
Red LED
Green LED
(1)
YES
Repair
NO
Power supply reset
Is it
normalized
YES
NO
Unit is normal
(malfunction by
accidental noise)
16
Error display :
e45
Red LED
Green LED
Indoor unit
Stays OFF
Keeps flashing
Outdoor unit
1 time flash
Keeps flashing
Red LED
Green LED
Does the
LED1 (Green) on the
inverter PCB
blink?
NO
YES
YES
Is the
power supply
line normal?
YES
Defective inverter PCB
NO
Repair
NO
Defective inverter PCB
Defective outdoor unit PCB
Broken Cnl in No.5 (See next page)
- The ourdoor unit PCB cannot receive signals.
- The inberter PCB cannot send signals.
- The watch dog signal cannot be taken.
Notes (1) Make a check referring to Troubleshooting for Inverter (page 933.)
(2) When receiving fails, the LED2 comes on at once. If the outdoor unit cannot receive signals for 10 seconds, the 52C is turned OFF.
Accordingly, the ON state can be checked only in this period of 10 seconds.
927
FDC-HKX
17
Error display :
Red LED
Green LED
e46
Indoor unit
Stays OFF
Keeps flashing
Red LED
Green LED
Outdoor unit
1 time flash
Keeps flashing
Are automatic
YES
address and manual address
coexstent on the same
network
NO
Power supply
detected between outdoor YES
unit terminal T5~PCB
faston terminal T6
(black)?
NO
928
Defective 20S
Replacement
FDC-HKX
Louver motor does not operate
2)
NO
NO
Is LM wire
broken?
YES
YES
YES
NO
Defective indoor
unit PCB
YES
Is LM
locked?
Replace LM
Normal
NO
It is normal
if it stops with
2 pushes on LS
NO
YES
Defective LS
Replacement
Defective indoor unit PCB
Replacement
3)
NO
Defective indoor unit PCB
Replacement
YES
Check with the Hi, Me, Lo of blower
mode.
Check FM1
Is Voltage detected
between CNF
terminals?
(1)
NO
YES
Defective FM1, capacitor
(CF1) Replacement
929
FDC-HKX
(ii) When the compressor does not operate although the remote controller display is normal (Without the
check display)
Take following steps first before confirming the following items:
Confirm that it is normal at the indoor unit side, LED1 (green) keeps flashing on the outdoor unit control PCB and LED2
(red) is not lit.
When LED1 (red) is flashing while the remote controller display is normal, LED2 (red) can be turned off if SW3-1 is turned
ON and turned OFF again.
Note (1) Be sure to turn the SW3-5 off after the confirmation.
NO
Is voltage detected on
52C coil?
YES
Replace 52C.
NO
YES
1
(From next page)
YES
Is indoor return air thermistor normal?
Is thermostat stopped?
NO
NO
Defective inverter
(See page 933.)
YES
NO
Note(1) Set 7 SEG indicator changeover
swich (SW4) to 0.
YES
Is voltage detected
between U,V,W on
power transistor?
YES
Diagnose errors on
LED's on inverter
PCB.
NO
YES
Defective compressor
NO
Defective inverter
Notes (1) Expansion valve of the indoor unit may be closed or the indoor fan may be stopped. Stop the compressor no sooner than it has started. Neglecting
this caution could result in compressor trouble.
(2) Method to check with the outdoor unit only is described on the next page.
930
FDC-HKX
2)
(Or pull out the connector CnA2 on the outdoor unit PCB)
NO
Does a voltage
Appear at the 52C coil
Is the 52C
turned ON?
YES
Defective 52C
NO
YES
YES
Can the compressor(1)
operate at 35Hz?
NO
1
(Continued to the previous page)
Note (1) When using this procedure, the indoor unit enters a transmission error state. In the indoor unit the expansion valve
may be closed or the fan may stop.
After the compressor is operated, stop it at once.
Otherwise, it will cause a failure to the compressor.
931
FDC-HKX
3)
NO
YES
Error on the power
supply system
Is LED1 (green)
on inverter PCB
flashing?
NO
Is DC 540V
detected at CNW on
inverter PCB?
NO
YES
YES
NO
YES
Check LED2 (red) error
contents.
(See page 934)
(iii) When the cooling (heating) effect is felt insufficient. (Check also the refrigeration cycle for the refrigerant
quantity, etc. in addition to the following.)
1)
applied.
Check the indoor controller output to the expansion valve with the following procedures.
Orange~Gray
Red~Gray
Yellow~Gray
Black~Gray
above.
Notes (1) 5V is maintained for 8 seconds after the power on, then it drops momentarily and recovers 5V for approx. 7
seconds.
(2) When measured with a digital multi-tester, voltages of approx. 6~3V are output one after another.
932
FDC-HKX
2)
NO
YES
Is LED1 (green)
on inverter PCB
flashing?
Is DC 540V
detected at CNW on
inverter PCB?
NO
YES1
YES
NO
Capacitor is defective.
Replace.
NO
Reactor is defective.
Replace.
NO
Resistor R1 is defective.
Replace.
NO
NO
NO
YES
YES
Does inverter
LED2 (red) light or
flash?
Is DC 540V
detected between
(+)~(-)?
NO2
NO
3
Is capacitor
normal?
Replacement
YES
YES
Compressor check
4
Is there continuity
on reactor?
YES
5
Is resistance
detected on resistor
R1?
YES
Is diode module
normal?
YES
Check 52C.
YES
7
Is there continuity
on noise filer?
933
If good
52C
7-segment
indicator
~
~
~
CN11
Detail of communication
It is normal if 5V or abnormal
if 0V
It is normal 5V or abnormal if OV
6 Inverter overheat
7 Current cut
12V
V (Analog tester)
0V
3 Transmission to inverter
1 Common
Connector
30
30
30
Tester probe
(Black)
LD1 LD2
Green Red
CNR
CNL
19 20 21 22 23 24 25
1 2 3 7 8 9 13 14 15
Inverter PCB
the compressor. The values vary depending on the kinds of measuring instrument.
U
CM
CnW
Tester probe
(Red)
Mark
DC540V
* LED1 (Green)
1
2
3
4
5
6
7
Capacitor check
R1
FDC140
FDC224
FDC280
1
2
3
4
5
6
7
Noise filter
5
Continuity
6
~
If tester probes are inverted,
the connection becomes
open.
+
~
Tester probe
LED1 LED2
Red Green
Control PCB
Transformer
L3
L2
L1
TB
CNA2 CNA1
CNI1
934
CNI2
FDC-HKX