Beruflich Dokumente
Kultur Dokumente
Web Site
EIRE
0818 717100
www.samsung.com/ie/support
U.K
www.samsung.com/uk/support
LED TV
user manual
www.samsung.com/register
[UH6400-XU]BN68-05815A-02ENG.indb 1
BN68-05815A-02
2014-04-01
12:57:22
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable
operation of this apparatus, and to protect it from overheating, these slots and openings must never be blocked or covered.
-- Do not cover this apparatus in a confined space, such as a bookcase or built-in cabinet, unless proper ventilation is
provided.
-- Do not place this apparatus near or over a radiator or heat resistor, or where it is exposed to direct sunlight.
-- Do not place a vessel containing water (vases etc.) on this apparatus, as this can result in a risk of fire or electric shock.
Do not expose this apparatus to rain or place it near water (near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool etc.). If this apparatus accidentally gets wet, unplug it and contact an authorised dealer
immediately. Make sure to pull out the power cord from the outlet before cleaning.
This apparatus use batteries. In your community there might be regulations that require you to dispose of these batteries
properly under environmental considerations. Please contact your local authorities for disposal or recycling information.
Do not overload wall outlets, extension cords or adaptors beyond their capacity, since this can result in fire or electric shock.
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plug end, adaptors and the point where they exit from the appliance.
To protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time, unplug
it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and
power line surges.
Before connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor
corresponds to the local electrical supply.
Never insert anything metallic into the open parts of this apparatus. Doing so may create a danger of electric shock.
To avoid electric shock, never touch the inside of this apparatus. Only a qualified technician should open this apparatus.
Make sure to plug the power cord in until it is firmly inserted. When removing the power cord, make sure to hold the power
plug when pulling the plug from the outlet. Do not touch the power cord with wet hands.
If this apparatus does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it
immediately and contact an authorised dealer or service centre.
Be sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an extended
period of time (especially when children, elderly or disabled people will be left alone in the house).
-- Accumulated dust can cause an electric shock, an electric leakage or a fire by causing the power cord to generate sparks
and heat or the insulation to deteriorate.
Be sure to contact an authorised service centre, when installing your set in a location with heavy dust, high or low
temperatures, high humidity, chemical substances and where it operates for 24 hours such as the airport, the train station
etc. Failure to do so may cause serious damage to your set.
Use only a properly grounded plug and receptacle.
-- An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug
shall be readily operable.
Do not allow children to hang onto the product.
Store the accessories (battery, etc.) in a location safely out of the reach of children.
Do not install the product in an unstable location such as a shaky self, a slanted floor or a location exposed to vibration.
Do not drop or impart any shock to the product. If the product is damaged, disconnect the power cord and contact a service
centre.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such
as wax, benzene, alcohol, thinners, insecticide, aerial freshener, lubricant or detergent. This may damage the appearance or
erase the printing on the product.
Apparatus shall not be exposed to dripping or splashing.
Do not dispose of batteries in a fire.
Do not short circuit, disassemble or overheat the batteries.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
WARNING - TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS
PRODUCT AT ALL TIMES.
English - 2
This TV features Smart Hub, a multi-purpose entertainment and family centre. With Smart
Hub, users can surf the web, download applications, and stay in touch with family and friends
through social networking services. In addition, you can enjoy photo, video, and music files
stored on external storage devices.
Press the button to launch Smart Hub. Choose a service using the displayed panels.
Games: You can view all game apps provided by Smart Hub and download and play
a desired game. In addition, you can manage games that you have downloaded or
purchased with your Samsung Account.
SAMSUNG APPS: Download and install applications such as Web Browser.
FILMS AND TV SHOWS: Purchase and watch movies and series without a separate external
MULTIMEDIA: Play photo, video and music files from all compatible devices.
Anynet+ (HDMI-CEC)
This allows you to control all connected Samsung devices that support Anynet+ with your
Samsung TVs remote control.
e-Manual
Provides a detailed, on-screen user manual built into your TV. (page 28)
* The figures and illustrations in this User Manual are provided for reference only and may
differ from the actual product appearance. The product design and specifications may change
without notice. CIS languages (Russian, Ukrainian, Kazakhs) are not available for this product,
since this is manufactured for customers in the EU region.
English - 3
Contents
01 What's in the Box?
02 Assembling the TV
7
Mounting the TV on the Wall Using the Wall Mount Kit (Optional)
English - 4
English - 5
Regulatory Guide
Power Cord
User Manual
CI Card Adapter
IR Extender Cable
Cable Holder
English - 6
Don't Touch
This Screen!
02Assembling the TV
Attaching the TV to the Stand
X7 (M4 X L12): 32
X8 (M4 X L12): 40~ 55
X8 (M4 X L10): 60~ 65
Make sure you have all the accessories shown, and that you assemble the stand following the
provided assembly instructions.
English - 7
Inches
VESA Spec.
(A * B)
32 ~ 40
200 X 200
LED-TV
48 ~ 75
Standard
Screw
Quantity
M8
400 X 400
Do not install your Wall Mount Kit while your TV is turned on. It may result in
personal injury due to electric shock.
English - 8
10 cm
10 cm
10 cm
10 cm
10 cm
Other Cautions
-- The actual appearance of the TV may differ from the images in this manual, depending on
the model.
-- Be careful when you touch the TV. Some parts can be somewhat hot.
English - 9
put the screws into the clamps, and then fasten the
screws into the TV again.
-- Screws may not be supplied with the product. In
this case, please purchase screws of the following
specifications.
-- Screw Specifications: For a 32 ~ 75 inches: M8
wall
4. Verify that all connections are properly secured. Periodically check connections for any
sign of damage. If you have any doubt about the security of your connections, contact a
professional installer.
English - 10
English - 11
You can connect various external devices using the connectors located at the back of the
product. Check the connectors and then refer to the Quick Guide for more instructions on
supported external devices.
English - 12
Connecting to a Network
Connecting the TV to a network gives you access to online services such as the Smart Hub, as
well as software updates.
-- The shape of the rear panel differs among the models.
TV Rear Panel
External Modem
(ADSL / VDSL / Cable TV)
Modem Cable
(Not Supplied)
LAN Cable
(Not Supplied)
English - 13
TV Rear Panel
External Modem
(ADSL / VDSL / Cable TV)
Modem Cable
(Not Supplied)
IP Router with a
DHCP Server
LAN Cable
(Not Supplied)
LAN Cable
(Not Supplied)
TV Rear Panel
English - 14
-- Please locate the two holes at the back of the TV next to the COMMON INTERFACE port.
2. Connect the CI CARD Adapter to the COMMON INTERFACE port on the product 2.
3. Insert the CI or CI+ CARD.
We recommend that you attach the CI Card adapter and insert the CI card (viewing
card) before you mount the TV on the wall because it may be difficult and
dangerous to do this when it is on the wall.
English - 15
NOTE
-- You must obtain a CI or CI+ CARD from a local cable service provider.
-- When removing the CI or CI+ CARD, carefully pull it out as dropping the CI or CI+ CARD
may damage it.
-- Insert the CI or CI+ CARD in the direction marked on the card.
-- The location of the COMMON INTERFACE slot may differ depending on the model.
-- A CI or CI+ CARD is not supported in some countries and regions, therefore, check with
your authorised dealer.
-- If you have any problems, please contact a service provider.
-- Insert the CI or CI+ CARD that supports the current aerial settings. The screen will be
distorted or will not be visible.
English - 16
comes loose.
2. Insert 2 AAA alkaline batteries, making sure to align the positive and negative polarities
correctly.
3. Place the battery cover on the remote control and insert the cover into the remote control.
4. Slide the battery cover in the order shown so that the cover is completely attached to the
remote control.
1. Gently pull on the battery cover's notch and then remove the cover completely once it
comes loose.
2. Insert 2 AA alkaline batteries, making sure to align the positive and negative polarities
correctly.
3. Place the battery cover on the remote control and insert the top part of the cover into the
remote control.
4. Press the catches on both sides of the battery cover in the order shown so that the cover is
English - 17
Remote Control
Learn where the function buttons are on your remote, such as: SOURCE, MUTE, Y, < P
>, MENU, TOOLS, E, INFO, CH LIST, RETURN, GUIDE and EXIT.
-- This remote control has Braille points on the Power, Channel, and Volume buttons and can be
used by visually impaired persons.
-- Your TV also comes with a Samsung Smart Control. For information about the Samsung
Smart Control, refer to the page 19.
Displays programme
information on the TV screen.
Exits the menu.
English - 18
: Turns the
sound on/off.
AD: Press and hold
this button to bring
up the Accessibility
Shortcuts panel.
Select the options
to turn them on or
off.
channel broadcasting
schedule.
CH.LIST: Press and hold to
launch the channel list.
the screen.
English - 19
Turning on the TV
Turn on the TV using the P button on the remote control or TV panel.
-- The product colour and shape may vary depending on the model.
-- The TVs Controller, a small joystick-like button at the right back of the TV, lets you control
the TV without the remote control.
Function menu
R
P
TV Controller
English - 20
Initial setup
The initial setup dialogue box appears when the TV is first activated. Follow the on-screen
instructions to finish the initial setup process such as selecting the menu language, scanning
channels, connecting to the network, and more. During each step, either make a choice
or skip the step. You can manually perform this process at a later time in the System > Setup
menu.
-- If you connect any external device to HDMI1 before starting initial setup, the source of your
live TV signal is set to STB. After finishing with this process, you will not be able to scan all
channels and stores them in the TVs memory.
-- If you want to connect aerial cable to your TV, select Aerial. In this case, you will be able to
scan all channels and stores them in the TVs memory.
postcode and select your Freeview, Freesat or external satellite television provider from the
displayed list.
4. Set-top Box Control Test: This test is to check if your TV remote is able to control your Set-top
Box. This step only occurs if Set-top box was selected in step 1.
Password Change
System > Change PIN
password is 0-0-0-0.
2. Enter a new password and then enter it again to confirm it. The password change is
complete.
-- If you forgot your PIN code, press the buttons in the following sequence to reset the PIN to
0-0-0-0:
For the Standard Remote Control: In Standby mode: MUTE 8 2 4 POWER (On)
For the Samsung Smart Control: When the TV turns on: MUTE Volume up RETURN
Volume down RETURN Volume up RETURN
English - 21
05 Selecting Connected
Devices
You can select a connected external device using the SOURCE button.
For example, to switch to a gaming console connected to the second HDMI connector,
press SOURCE. From the Source list, select HDMI2 to change the input signal to HDMI mode.
Connector names may vary depending on the model.
-- For some compatible devices connected via SCART or HDMI sockets, the TV may
automatically select the correct source when this device is accessed. For this to work, the
HDMI Anynet+ system must be switched on (System > Anynet+ (HDMI-CEC)). Anynet+ will
also automatically power off compatible HDMI devices when the TV is switched off.
The following options are available in the Source screen:
Additional functions
Select a port connected to an external device, and press and hold the Enter button. The
following functions are available:
-- Available options for each connector may vary.
Edit Name
Rename devices connected to the TV for easier identification of external sources.
For example, you can designate a computer connected to the TV via an HDMI-DVI cable as
DVI PC.
Alternatively, simply designate a computer connected to the TV via an HDMI cable as PC.
You can also designate an AV device connected to the TV via an HDMI-DVI cable as DVI
Devices.
Information
View detailed information about the connected devices.
Anynet+ (HDMI-CEC)
Displays a list of Anynet+ (HDMI-CEC)-compliant devices that are connected to the TV.
-- This option is only available when Anynet+ (HDMI-CEC) is On.
English - 22
English - 23
If the Samsung Smart Control stops operating or works abnormally, replace the batteries as
this may be due to insufficient battery power.
If the problem persists, follow the directions below:
1. Press both the RETURN button and the GUIDE button simultaneously for more than 3
seconds.
-- You must place the Samsung Smart Control approximately 30cm ~ 40cm away from
the TV and ensure it is pointing towards the remote control receiver.
2. Connection image is displayed on the screen. And then, Samsung Smart Control is
connecting to TV automatically.
English - 24
English - 25
English - 26
10 cm
Source screen.
2. Select
Universal remote setup from the top of the screen. This initiates the universal
English - 27
3. Select an item from the list. This opens the e-Manual on the corresponding page.
English - 28
2. Press and hold the Enter button. The Options menu appears.
3. From the Options menu on the screen, select Update Apps. A popup window appears.
English - 29
08 Troubleshooting and
Maintenance
Troubleshooting
If you have any questions about the TV, first refer to the Troubleshooting list below. If none
of these troubleshooting tips apply, please visit www.samsung.com and click on Support, or
contact the call centre listed on the back cover of this manual.
Issues
Make sure the AC power cord is securely plugged into the wall
outlet and the TV.
Make sure the wall outlet is working.
Try pressing the P button on the TV to make sure the problem is
not the remote. If the TV turns on, refer to the Remote control
does not work item below.
Check the cable connections. Remove and reconnect all cables
connected to the TV and external devices.
Set the video outputs of your external devices (Cable/Sat Box,
DVD, Blu-ray etc) to match the TV's input connections. For
example, if the output of an external device is HDMI, it should
be connected to an HDMI input on the TV.
Make sure your connected devices are powered on.
Be sure to select the correct input source.
Reboot the connected device by unplugging it, and then
reconnecting the devices power cable.
Replace the remote control batteries. Make sure the batteries
are installed with their polarities (+/) in the correct direction.
Clean the sensors transmission window on the remote.
Try pointing the remote directly at the TV from 1.5 ~ 1.8 m
away.
Programme the Cable/Set remote control to operate the TV.
Refer to the Cable/Set-Top-Box user manual for the SAMSUNG
TV code.
There is no picture/
video.
-- This TFT LED panel uses a panel consisting of sub pixels which require sophisticated
technology to produce. There may, however be a few bright or dark pixels. These pixels will
have no impact on the performance of the product.
-- To keep your TV running optimally upgrade to the latest firmware on the Samsung website
via the USB device USB (Samsung.com > Support > Downloads).
-- Some of the pictures and functions above are available for specific models only.
English - 30
The Eco Sensor measures the light in the room and optimises the brightness of the TV
automatically to reduce power consumption. This causes the TV to brighten and dim
automatically. To turn this function off, go to System > Eco Solution > Eco Sensor.
Do not block the sensor with any material. This may decrease the picture brightness.
1. Eco Sensor: This power-saving feature automatically adjusts the screen brightness of the TV
2. To enable or disable the Eco Sensor, go to System > Eco Solution > Eco Sensor and select On or
Off.
3. Please note: If the screen is too dark while watching TV in a dark environment, this may be
English - 31
Diagnose your TV
on your TV and
go to the Support
section.
3. Select Remote
Management and
Provide the Pin# to
the agent.
Do not spray water directly onto the product. Clean the product with a soft damp cloth
Any liquid that enters the product may result using a small amount of water. Do not use a
in product failure, fire, or electric shock.
flammable liquid (e.g. benzene, thinners) or
a cleaning agent.
English - 32
1920 x 1080
UE40H6400
32 inches
40 inches
5.5 kg
6.5 kg
8.2 kg
9.4 kg
UE48H6400
UE50H6400
48 inches
50 inches
11.9 kg
13.5 kg
13.2 kg
14.8 kg
English - 33
Model Name
Screen Size (Diagonal)
Dimensions (W x H x D)
Body
With stand
Weight
Without Stand
With Stand
UE55H6400
UE65H6400
55 inches
65 inches
16.6 kg
18.2 kg
26.1 kg
28.7 kg
Model Name
UE75H6400
75 inches
1687.0 x 970.0 x 70.9 mm
1687.0 x 1051.1 x 350.3 mm
Weight
Without Stand
With Stand
33.1 kg
35.0 kg
-- The design and specifications are subject to change without prior notice.
-- For information about the power supply, and about power consumption, refer to the label
attached to the product.
-- Typical power consumption is measured according to IEC 62087 Ed.2
Standby mode
To decrease power consumption, unplug the power cord when the TV will not be used for a
long time.
English - 34
Licences
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
Hereby, Samsung Electronics, declares that this TV is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
The official Declaration of Conformity may be found at http://www.samsung.com, go to
Support > Search Product Support and enter the model name.
This equipment may only be used indoors.
This equipment may be operated in all EU countries.
English - 35
-- WARNINGS: Image retention, commonly known as screen burn-in, can occur on most
types of television if the same image is displayed continuously. The most common causes
of image retention are logos that remain stationary on the TV screen. These logos are
common on many programmes received via a Set-top Box. To reduce this risk, avoid
displaying still images for long durations and lower the brightness or contrast settings
to decrease the intensity of the picture. Extended viewing of movies and programmes in
aspect ratios that are different from the aspect ratio of the TV may cause image retention.
Always try to avoid black borders at the top or bottom by using the zoom function. This
will help eliminate the black borders and fit the picture to the entire area of the screen.
Using a video game console may cause image retention and is not recommended. When
using a PC input, avoid displaying still images for long durations and reduce the brightness
or contrast settings to decrease the intensity of the picture.
-- IMPORTANT: Image retention issues are not covered by your Samsung warranty.
English - 36
Warranty Card
United Kingdom
This Samsung product is warranted for a period of twelve (12) months from the original date of purchase, against defective materials
and workmanship. In the event that warranty service is required, you should return the product to the retailer from whom it was
purchased. However, Samsung Authorised Dealers and Authorised Service Centres in other EC Countries will comply with the warranty
on the terms issued to purchasers in the country concerned. In case of difficulty, details of our Authorised Service Centres are available
from:
Samsung Electronics U.K. Ltd.
Customer Care Centre
PO Box 479
GATESHEAD NE9 9BJ
United Kingdom
Tel: 0330 SAMSUNG (7267864) / Fax: 0330 7260001 (UK & Northern Ireland)
Tel: 0818 717100 / Fax: +44 117 915 6736 (EIRE Only)
Web: www.samsung.com
WARRANTY CONDITIONS
1. The warranty is only valid if, when warranty service is required, the warranty card is fully and properly completed and is presented
with the original invoice or sales slip or confirmation, and the serial number on the product has not been defaced.
2. Samsungs obligations are limited to the repair or, at its discretion, replacement of the product or the defective part.
3. Warranty repairs must be carried out by Authorised Samsung Dealers or Authorised Service Centres. No re-imbursement will be
made for repairs carried out by non Samsung Dealers and, any such repair work and damage to the products caused by such repair
work will not be covered by this warranty.
4. This product is not considered to be defective in materials nor workmanship by reason that it requires adaptation in order to
conform to national or local technical or safety standards in force in any country other than the one for which the product was
originally designed and manufactured.
5. This warranty covers none of the following:
a) Periodic check ups, maintenance and repair or replacement of parts due to normal wear and tear.
b) Cost relating to transport, removal or installation of the product.
c) Misuse, including the failure to use this product for its normal purposes or incorrect installation.
d) Damage caused by Lightning, Water, Fire, Acts of God, War, Public Disturbances, incorrect mains voltage, improper ventilation
or any other cause beyond the control of Samsung.
e) Spillage of food or liquid or use of any other hazardous substances, which may effect the product.
f) Performance due to differences in broadcasting method between countries
6. This warranty is valid for any person who legally acquired possession of the product during the warranty period.
7. The consumers statutory rights in any applicable national legislation whether against the retailer arising from the purchase contract
or otherwise are not affected by this warranty. Unless there is national legislation to the contrary, the rights under this warranty are the
consumers sole rights and Samsung, its subsidiaries and distributors shall not be liable for indirect or consequential loss or any damage
to records, compact discs, videos or audio taper or any other related equipment or material.
8. Some products may differ from these guidelines. Please check with your dealer or the local Samsung web-site.
WARNING
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE LETTER E OR
BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.